ADDER SYSTEM CABLE L

Transcription

1 17

2 Introduction CALE LADDE The ICMS cable ladder system consists of a wide range of aluminum and Steel cable ladders, Fittings and accessories. Ladder Trays are available in two models: Tubular rungs mechanically swaged to side rails. C-Profile rungs arc welded to side rails in two options Outside flange construction (shown in the catalogue) Inside flange construction (Upon request) It is the perfect solution for a wide variety of installations where corrosion-resistance, high loading capacity with long spans and quick and easy installation is needed. The advantages of ZETA LADDE are appreciated particularly in demanding conditions or complex installations, for example in industrial plants, chemical and petrochemical plants, in tunnel and bridge constructions, water treatment works, outdoors and in close proximity to the sea. elated Standards: NEMA VE-1 S EN 61537:2007 Straight Ladder Ordering Way : Example: ** Model NEMA Class Load Depth ZST 12C AL ung Spacing Width Length Material/Finish. ZST 8A 12-A 3 (76 mm) 06 (152 mm) 06 (152 mm) 10 (3.0 mtr) PG: Pre galvanized Steel ZSC 12 4 (102 mm) 09 (229 mm) 09 (229 mm) 12 (3.7 mtr) HG: Hot Dip Galvanized 12C 5 (127 mm) 12 (305 mm) 12 (305 mm) 20 (6.0 mtr) AL: Aluminum 16A 6 (152 mm) 18 (457 mm) 18 (457 mm) 24 (7.3 mtr) S4: Stainless Steel (610 mm) S6: Stainless Steel C 30 (762 mm) CA: Corten-A Steel 20A 36 (914 mm) HP: Hot Dip Galvanized 20 & Epoxy Powder Coated Example Explanation: 20C *HDG To S EN 1461 *For other finishing consult factory Cable Ladder straight. Tubular swaged rugs type. NEMA class 12:C. Load depth 76mm (3 ). ung spacing 229mm (9 ). Inside width 457mm (18 ). Length 6.0m (20 ). Material: Aluminum 18 **Applicable for the NEMA Cable ladder only

3 Straight ladder Model ZST: Tubular ungs Ladder Model ZSC: C-Profile ungs Ladder Cross Section Flange Width Flange Width Load Depth ungs Construction: ungs Attached to side rails by mechanical Swaging process. O.D. 1 ungs Construction: Load Depth ungs Attached to side rails by Arc Welding. 1 1/8 1 Hole Configuration 1/ 2 75mm (3 ) 102mm (4 ) Lo Side Height 108mm (41/4 ) 133mm (51/4 ) 75mm (3 ) 102mm (4 ) 108mm (41/4 ) 133mm (51/4 ) 127mm (5 ) 152mm (6 ) Load Depth Side He eight 159mm (61/4 ) 184mm (71/4 ) 127mm (5 ) 152mm (6 ) 159mm (61/4 ) 184mm (71/4 ) 19

4 Load Data Table Aluminium Cable Ladder Aluminum Ladder Model No. Span: 6 ft. Span: 8 ft. Span: 10 ft. Span: 12 ft. Span: 16 ft. Span: 20 ft. Span: 24 ft. Tubular ung ZST C-Profile ung ZSC Load Def. Load Def. Load Def. Load Def. Load Def. Load Def. Load Def. (lb/ft) (in) (lb/ft) (in) (lb/ft) (in) (lb/ft) (in) (lb/ft) (in) (lb/ft) (in) (lb/ft) (in) ZST 12A 3 ZSC 12A ZST 12 3 ZSC ZST 12C 3 ZSC 12C ZST 16A 3 ZSC 16A ZST 16 3 ZSC ZST 16C 3 ZSC 16C ZST 20A 3 ZSC 20A ZST 20 3 ZSC ZST 20C 3 ZSC 20C ZST 12A 4 ZSC 12A ZST 12 4 ZSC ZST 12C 4 ZSC 12C ZST 16A 4 ZSC 16A ZST 16 4 ZSC ZST 16C 4 ZSC 16C ZST 20A 4 ZSC 20A ZST 20 4 ZSC ZST 20C 4 ZSC 20C ZST 12A 5 ZSC 12A ZST 12 5 ZSC ZST 12C 5 ZSC 12C ZST 16A 5 ZSC 16A ZST 16 5 ZSC ZST 16C 5 ZSC 16C ZST 20A 5 ZSC 20A ZST 20 5 ZSC ZST 20C 5 ZSC 20C ZST 20C+ 5 ZSC 20C ZST 12A 6 ZSC 12A ZST 12 6 ZSC ZST 12C 6 ZSC 12C ZST 16A 6 ZSC 16A ZST 16 6 ZSC ZST 16C 6 ZSC 16C ZST 20A 6 ZSC 20A ZST 20 6 ZSC ZST 20C 6 ZSC 20C ZST 20C+ 6 ZSC 20C Data above based on simple beam tests as per NEMA VE-1 ungs Load capacity 200 lbs (0.89 KN) concentrated load applied at center of the rung with safety factor: 1.5 Deflection is reduced to approx. 50% when cable ladders used in continuous spans. Load: Allowable Uniform in Lbs/ft. to convert to Kg/ m. multiply by 1.48 Data in table based on 1.5 safety factor,to change to 2 multiply load by 0.75

5 Load Data Table Steel & SS Ladder Model No. Tubular ung ZST C-Profile ung ZSC Span: Load (lb/ft) 6 ft. Def. (in) Span: Load (lb/ft) Steel & SS Cable Ladder 8 ft. Def. (in) Span: Load (lb/ft) 10 ft. Def. (in) Span: Load (lb/ft) ZST 12A 3 ZSC 12A ZST 12 3 ZSC ZST 12C 3 ZSC 12C ft. Def. (in) Span: Load (lb/ft) ZST 16A 3 ZSC 16A ZST 16 3 ZSC ZST 16C 3 ZSC 16C ZST 20A 3 ZSC 20A ZST 20 3 ZSC ZST 20C 3 ZSC 20C ZST 12A 4 ZSC 12A ZST 12 4 ZSC ZST 12C 4 ZSC 12C ZST 16A 4 ZSC 16A ZST 16 4 ZSC ZST 16C 4 ZSC 16C ZST 20A 4 ZSC 20A ZST 20 4 ZSC ZST 20C 4 ZSC 20C ZST 12A 5 ZSC 12A ZST 12 5 ZSC ZST 12C 5 ZSC 12C ZST 16A 5 ZSC 16A ZST 16 5 ZSC ZST 16C 5 ZSC 16C ZST 20A 5 ZSC 20A ZST 20 5 ZSC ZST 20C 5 ZSC 20C ZST 20C+ 5 ZSC 20C ZST 12A 6 ZSC 12A ZST 12 6 ZSC ZST 12C 6 ZSC 12C ZST 16A 6 ZSC 16A ZST 16 6 ZSC ZST 16C 6 ZSC 16C ZST 20A 6 ZSC 20A ZST 20 6 ZSC ZST 20C 6 ZSC 20C ZST 20C+ 6 ZSC 20C ft. Def. (in) Span: Load (lb/ft) 20 ft. Def. (in) Span: Load (lb/ft) 24 ft. Def. (in) Design cross-sectional area as per NEC shows the minimum area of both side rails required for cable tray to be used as Equipment Grounding Conductor (EGC) for specific short circuit current rating. 21

6 Selection Table Aluminum Ladder Model No. Tubular ung ZST C-Profile ung ZSC NEMA VE-1 Classification Aluminium Cable Ladder NEMA VE-1 (Load/Span) Nominal Load Depth in (mm) Overall Side ail Height in (mm) Flange Width in (mm) ZST 12A 3 ZSC 12A 3 8A -12A 50 lb/ft@12> span 13/16»(21mm) 0.60 ZST 12 3 ZSC lb/ft@12> span 13/16»(21mm) 0.60 ZST 12C 3 ZSC 12C 3 12C 100 lb/ft@12> span 13/16»(21mm) 1.00 ZST 16A 3 ZSC 16A 3 16A 50 lb/ft@16> span 3» 4 1/4» 13/16»(21mm) 1.00 ZST 16 3 ZSC lb/ft@16> span (76mm) (108mm) 1 1/4»(32mm) 1.50 ZST 16C 3 ZSC 16C 3 16C 100 lb/ft@16> span 1 1/4»(32mm) 1.50 ZST 20A 3 ZSC 20A 3 20A 50 lb/ft@20> span 1 1/4»(32mm) 1.50 ZST 20 3 ZSC lb/ft@20> span 1 1/2»(38mm) 2.00 ZST 20C 3 ZSC 20C 3 20C 100 lb/ft@20> span 1 1/2»(38mm) 2.00 ZST 12A 4 ZSC 12A 4 8A -12A 50 lb/ft@12> span 13/16»(21mm) 0.60 ZST 12 4 ZSC lb/ft@12> span 13/16»(21mm) 0.60 ZST 12C 4 ZSC 12C 4 12C 100 lb/ft@12> span 13/16»(21mm) 1.00 ZST 16A 4 ZSC 16A 4 16A 50 lb/ft@16> span 4» 5 1/4» 1 1/4»(32mm) 1.50 ZST 16 4 ZSC lb/ft@16> span (102mm) (133mm) 1 1/4»(32mm) 1.50 ZST 16C 4 ZSC 16C 4 16C 100 lb/ft@16> span 1 1/4»(32mm) 2.00 ZST 20A 4 ZSC 20A 4 20A 50 lb/ft@20> span 1 1/4»(32mm) 1.50 ZST 20 4 ZSC lb/ft@20> span 1 1/4»(32mm) 2.00 ZST 20C 4 ZSC 20C 4 20C 100 lb/ft@20> span 1 1/2»(38mm) 2.00 ZST 12A 5 ZSC 12A 5 8A -12A 50 lb/ft@12> span 13/16»(21mm) 1.00 ZST 12 5 ZSC lb/ft@12> span 13/16»(21mm) 1.00 ZST 12C 5 ZSC 12C 5 12C 100 lb/ft@12> span 13/16»(21mm) 1.00 ZST 16A 5 ZSC 16A 5 16A 50 lb/ft@16> span 5» 6 1/4» 1 1/4»(32mm) 1.00 ZST 16 5 ZSC lb/ft@16> span (127mm) (159mm) 1 1/4»(32mm) 1.00 ZST 16C 5 ZSC 16C 5 16C 100 lb/ft@16> span 1 1/4»(32mm) 2.00 ZST 20A 5 ZSC 20A 5 20A 50 lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20 5 ZSC lb/ft@20> span 1 1/4»(32mm) 1.50 ZST 20C 5 ZSC 20C 5 20C 100 lb/ft@20> span 1 1/2»(38mm) 2.00 ZST 20C+ 5 ZSC 20C+ 5 20C+ 100 lb/ft@24> span 2» (50.8mm) 2.00 ZST 12A 6 ZSC 12A 6 8A -12A 50 lb/ft@12> span 13/16»(21mm) 1.00 ZST 12 6 ZSC lb/ft@12> span 13/16»(21mm) 1.00 ZST 12C 6 ZSC 12C 6 12C 100 lb/ft@12> span 13/16»(21mm) 1.00 ZST 16A 6 ZSC 16A 6 16A 50 lb/ft@16> span 6» 7 1/4» 1 1/4»(32mm) 2.00 ZST 16 6 ZSC lb/ft@16> span (152mm) (184mm) 1 1/4»(32mm) 2.00 ZST 16C 6 ZSC 16C 6 16C 100 lb/ft@16> span 1 1/4»(32mm) 2.00 ZST 20A 6 ZSC 20A 6 20A 50 lb/ft@20> span 1 1/4»(32mm) 2.00 ZST 20 6 ZSC lb/ft@20> span 1 1/2»(38mm) 1.50 ZST 20C 6 ZSC 20C 6 20C 100 lb/ft@20> span 1 1/2»(38mm) 2.00 ZST 20C+ 5 ZSC 20C+ 6 20C+ 100 lb/ft@24> span 2» (50.8mm) 2.00 Design Cross-Sec. Area (sq.in) Design cross-sectional area as per NEC shows the minimum area of both side rails required for cable tray to be used as Equipment Grounding Conductor (EGC) for specific short circuit current rating. 22

7 Selection Table Steel Ladder Model No. Tubular ung ZST C-Profile ung ZSC NEMA VE-1 Classification Steel & SS Cable Ladder NEMA VE-1 (Load/Span) Nominal Load Depth in (mm) Overall Side ail Height in (mm) Flange Width in (mm) Design Cross-Sec. Area (sq.in) ZST 12A 3 ZSC 12A 3 8A -12A 50 lb/ft@12> span 13/16»(21mm) 0.40 ZST 12 3 ZSC lb/ft@12> span 13/16»(21mm) 0.40 ZST 12C 3 ZSC 12C 3 12C 100 lb/ft@12> span 13/16»(21mm) 0.70 ZST 16A 3 ZSC 16A 3 16A 50 lb/ft@16> span 3» 4 1/4» 1 1/4»(32mm) 0.40 ZST 16 3 ZSC lb/ft@16> span (76mm) (108mm) 1 1/4»(32mm) 0.70 ZST 16C 3 ZSC 16C 3 16C 100 lb/ft@16> span 1 1/4»(32mm) 1.00 ZST 20A 3 ZSC 20A 3 20A 50 lb/ft@20> span 1 1/4»(32mm) 0.70 ZST 20 3 ZSC lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20C 3 ZSC 20C 3 20C 100 lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 12A 4 ZSC 12A 4 8A -12A 50 lb/ft@12> span 13/16»(21mm) 0.40 ZST 12 4 ZSC lb/ft@12> span 13/16»(21mm) 0.40 ZST 12C 4 ZSC 12C 4 12C 100 lb/ft@12> span 13/16»(21mm) 0.40 ZST 16A 4 ZSC 16A 4 16A 50 lb/ft@16> span 4» 5 1/4» 1 1/4»(32mm) 0.70 ZST 16 4 ZSC lb/ft@16> span (102mm) (133mm) 1 1/4»(32mm) 0.70 ZST 16C 4 ZSC 16C 4 16C 100 lb/ft@16> span 1 1/4»(32mm) 0.70 ZST 20A 4 ZSC 20A 4 20A 50 lb/ft@20> span 1 1/4»(32mm) 0.70 ZST 20 4 ZSC lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20C 4 ZSC 20C 4 20C 100 lb/ft@20> span 1 1/4»(32mm) 1.50 ZST 12A 5 ZSC 12A 5 8A -12A 50 lb/ft@12> span 13/16»(21mm) 0.70 ZST 12 5 ZSC lb/ft@12> span 13/16»(21mm) 0.70 ZST 12C 5 ZSC 12C 5 12C 100 lb/ft@12> span 13/16»(21mm) 0.70 ZST 16A 5 ZSC 16A 5 16A 50 lb/ft@16> span 5» 6 1/4» 1 1/4»(32mm) 0.70 ZST 16 5 ZSC lb/ft@16> span (127mm) (159mm) 1 1/4»(32mm) 1.00 ZST 16C 5 ZSC 16C 5 16C 100 lb/ft@16> span 1 1/4»(32mm) 1.00 ZST 20A 5 ZSC 20A 5 20A 50 lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20 5 ZSC lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20C 5 ZSC 20C 5 20C 100 lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20C+ 5 ZSC 20C+ 5 20C+ 100 lb/ft@24> span 2» (50.8mm) 1.50 ZST 12A 6 ZSC 12A 6 8A -12A 50 lb/ft@12> span 13/16»(21mm) 0.70 ZST 12 6 ZSC lb/ft@12> span 13/16»(21mm) 0.70 ZST 12C 6 ZSC 12C 6 12C 100 lb/ft@12> span 13/16»(21mm) 0.70 ZST 16A 6 ZSC 16A 6 16A 50 lb/ft@16> span 6» 7 1/4» 1 1/4»(32mm) 1.00 ZST 16 6 ZSC lb/ft@16> span (152mm) (184mm) 1 1/4»(32mm) 1.00 ZST 16C 6 ZSC 16C 6 16C 100 lb/ft@16> span 1 1/4»(32mm) 0.70 ZST 20A 6 ZSC 20A 6 20A 50 lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20 6 ZSC lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20C 6 ZSC 20C 6 20C 100 lb/ft@20> span 1 1/4»(32mm) 1.00 ZST 20C+ 6 ZSC 20C+ 6 20C+ 100 lb/ft@24> span 1 3/4»(44mm) 1.50 Design cross-sectional area as per NEC shows the minimum area of both side rails required for cable tray to be used as Equipment Grounding Conductor (EGC) for specific short circuit current rating. 23

8 Fittings For a completely integrated system, the ZETA LADDE fittings provide: electrical continuity, continuous support, positive radius control, protection against physical damage, ease of installation...engineered performance and factory-controlled quality of components. Fittings have a max. rung spacing of 9 in. o.c. measured at the center line of the fitting. Fitting flanges are designed to maintain surface continuity inside the tray system and avoid exposed sharp edges. Fittings are designed with 3 (76mm) tangent for splicing integrity. Ladder Fittings Ordering Way : Example: HT T 4 AL Fitting Type adius Width Model Load Depth Material/Finish. H90: 90Deg.Horizontal Elbow 305 mm (12 ) 152 mm (06 ) T: Tubular ungs Swaged 76 mm (3 ) PG: Pre galvanized Steel H60: 60Deg.Horizontal Elbow H45: 45Deg.Horizontal Elbow H30: 30Deg.Horizontal Elbow HT: Horizontal Tee HC: Horizontal Cross VI90: 90Deg.Vertical Inside Elbow 610 mm (24 ) 914 mm (36 ) 229 mm (09 ) 305 mm (12 ) 457 mm (18 ) 610 mm (24 ) 762 mm (30 ) 914 mm (36 ) C: C-Profile ungs Welded 102 mm (4 ) 127 mm (5 ) 152 mm (6 ) HG: Hot Dip Galvanized AL: Aluminum S4: Stainless Steel 304 S6: Stainless Steel 316 HP: Hot Dip Galvanized & Epoxy Powder Coated VI60: 60Deg.Vertical Inside Elbow *For other finishing consult factory VI45: 45Deg.Vertical Inside Elbow VI30: 30Deg.Vertical Inside Elbow VO90: 90Deg.Vertical Outside Elbow VO60: 60Deg.Vertical Outside Elbow VO45: 45Deg.Vertical Outside Elbow VO30: 30Deg.Vertical Outside Elbow VT: Vertical Tee VS: Vertical Support fitting HYL: Horizontal- Y Left HY: Horizontal- Y ight S: educer straight : educer ight Hand L: educer Left Hand Above Example: 24 Fitting, Horizontal Tee, Tubular ungs Type 3, Load Depth 1/4 4, Side rail height 24, adius18, Wide, Material Aluminum.

9 Fittings H45 45 Deg Horizontal Elbow Fitting adius Width Part No in Width (mm) in (mm) Model no - Prefix in (mm) H30 06 (152mm) H prefix 10 5/8 (270) 09 (229mm) H prefix 11 5/8 (295) H prefix 12 3/4 (324) 18 (457mm) H prefix 14 7/8 (378) H prefix 17 (432) 30 (762mm) H prefix 19 1/8 (486) H prefix 21 1/4 (540) 06 (152mm) H prefix 19 1/8 (486) 09 (229mm) H prefix 20 1/8 (511) H prefix 21 1/4 (540) 18 (457mm) H prefix 23 3/8 (594) H prefix 25 1/2 (648) 30 (762mm) H prefix 27 5/8 (702) H prefix 29 3/4 (756) 06 (152mm) H prefix 27 5/8 (702) 09 (229mm) H prefix 28 5/8 (727) H prefix 29 3/4 (756) 18 (457mm) H prefix 31 7/8 (810) H prefix 34 (864) 30 (762mm) H prefix 36 1/8 (918) H prefix 38 1/4 (972) Fitting adius Width Part No in Width (mm) in (mm) Model no - Prefix in (mm) 30 Deg Horizontal Elbow 06 (152mm) H prefix 7 1/2 (191) 09 (229mm) H prefix 8 1/4 (210) H prefix 9 (229) 18 (457mm) H prefix 10 1/2 (267) H prefix 12 (305) 30 (762mm) H prefix 13 1/2 (343) H prefix 15 (381) 06 (152mm) H prefix 13 1/2 (343) 09 (229mm) H prefix 14 1/4 (362) H prefix 15 (381) 18 (457mm) H prefix 16 1/2 (419) H prefix 18 (457) 30 (762mm) H prefix 19 1/2 (495) H prefix 21 (533) 06 (152mm) H prefix 19 1/2 (495) 09 (229mm) H prefix 20 1/4 (514) H prefix 21 (533) 18 (457mm) H prefix 22 1/2 (572) H prefix 24 (610) 30 (762mm) H prefix 25 1/2 (648) H prefix 27 (686) 45 For Making 45 Deg. turns on the same plan. W For Making 30 Deg. turns on the same plan. 30 W 25

10 Fittings H90 90 Deg Horizontal Elbow Fitting adius Width Part No in Width (mm) in (mm) Model no - Prefix in (mm) 06 (152mm) H prefix 18 (457) For Making 90 Deg. turns on the same plan. 09 (229mm) H prefix 21 (533) H prefix 24 (610) 18 (457mm) H prefix 30 (762) H prefix 36 (914) 30 (762mm) H prefix 42 (1067) H prefix 48 (1219) 06 (152mm) H prefix 30 (762) 09 (229mm) H prefix 33 (838) H prefix 36 (914) 18 (457mm) H prefix 42 (1067) H prefix 48 (1219) 30 (762mm) H prefix 54 (1372) H prefix 60 (1524) W 06 (152mm) H prefix 42 (1067) 09 (229mm) H prefix 45 (1143) H prefix 48 (1219) 18 (457mm) H prefix 54 (1372) H prefix 60 (1524) 30 (762mm) H prefix 66 (1676) H prefix 72 (1829) H60 60 Deg Horizontal Elbow Fitting adius Width Part No in Width (mm) in (mm) Model no - Prefix in (mm) 06 (152mm) H prefix 13 (330) For Making 60 Deg. turns on the same plan. 09 (229mm) H prefix 14 1/4 (362) H prefix 15 5/8 (379) 18 (457mm) H prefix 18 1/4 (464) H prefix 20 3/4 (527) 30 (762mm) H prefix 23 1/4 (591) H prefix 26 (660) 06 (152mm) H prefix 23 3/8 (594) 09 (229mm) H prefix 24 3/4 (629) H prefix 26 (660) 18 (457mm) H prefix 28 5/8 (727) H prefix 31 1/4 (794) 30 (762mm) H prefix 33 3/4 (857) H prefix 36 3/8 (924) 06 (152mm) H prefix 33 3/4 (857) 09 (229mm) H prefix 35 1/8 (892) H prefix 36 3/8 (924) 18 (457mm) H prefix 39 (991) 60 W H prefix 41 5/8 (1057) 30 (762mm) H prefix 44 1/8 (1121) 26 H prefix 46 3/4 (1187)

11 Fittings HT Horizontal Tee Fitting adius Width Part No A in Width (mm) in (mm) Model no - Prefix in (mm) in (mm) HC 06 (152mm) HT prefix 18 (457) 24 (610) 09 (229mm) HT prefix 21 (533) 30 (762) HT prefix 24 (610) 36 (914) 18 (457mm) HT prefix 30 (762) 48 (1219) HT prefix 36 (914) 20 (1524) 30 (762mm) HT prefix 42 (1067) 72 (1829) HT prefix 48 (1219) 84 (2134) 06 (152mm) HT prefix 30 (762) 36 (914) 09 (229mm) HT prefix 33 (838) 42 (1067) HT prefix 36 (914) 48 (1219) 18 (457mm) HT prefix 42 (1067) 60 (1524) HT prefix 48 (1219) 72 (1829) 30 (762mm) HT prefix 54 (1372) 84 (2134) HT prefix 60 (1524) 96 (2438) 06 (152mm) HT prefix 42 (1067) 48 (1219) 09 (229mm) HT prefix 45 (1143) 54 (1372) HT prefix 48 (1219) 60 (1524) 18 (457mm) HT prefix 54 (1372) 72 (1829) HT prefix 60 (1524) 84 (2134) 30 (762mm) HT prefix 66 (1676) 96 (2438) HT prefix 72 (1829) 108 (2743) Fitting adius Width Part No in Width (mm) in (mm) Model no - Prefix in (mm) Horizontal Cross 06 (152mm) HC prefix 24 (610) 09 (229mm) HC prefix 30 (762) HC prefix 36 (914) 18 (457mm) HC prefix 48 (1219) HC prefix 60 (1524) 30 (762mm) HC prefix 72 (1829) HC prefix 84 (2134) 06 (152mm) HC prefix 36 (914) 09 (229mm) HC prefix 42 (1067) HC prefix 48 (1219) 18 (457mm) HC prefix 60 (1524) HC prefix 72 (1829) 30 (762mm) HC prefix 84 (2134) HC prefix 96 (2438) 06 (152mm) HC prefix 48 (1219) 09 (229mm) HC prefix 54 (1372) HC prefix 60 (1524) 18 (457mm) HC prefix 72 (1829) HC prefix 84 (2134) 30 (762mm) HC prefix 96 (2438) HC prefix 108 (2743) For Making right angle turns on the same plan. For branch to tray with narrower width than main tray, use reducers or consult factory. A For Making right angle turns on the same plan. For branch to tray with narrower width than main tray, use reducers or consult factory. W W W W 27

12 Fittings VO45 45 Deg Vertical Outside Elbow Width ( W ) For 45 Deg. External corners or directional changes on a vertical plane. adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) VO4 12W3 - prefix 10 (254) VO30 4 (102mm) VO4 12W4 - prefix 10 3/8 (264) 5 (127mm) VO4 12W5 - prefix 10 6/8 (273) 6 (152mm) VO4 12W6 - prefix /8 (283) 3 (76mm) VO4 24W3 - prefix /8 (470) 4 (102mm) VO4 24W4 - prefix /8 (479) 5 (127mm) VO4 24W5 - prefix /8 (489) 6 (152mm) VO4 24W6 - prefix /8 (610) 3 (76mm) VO4 36W3 - prefix (838) 4 (102mm) VO4 36W4 - prefix 27 3/8 (695) 5 (127mm) VO4 36W5 - prefix 27 5/8 (702) 6 (152mm) VO4 36W6 - prefix 28 (711) 30 Deg Vertical Outside Elbow LD For 30 Deg. External corners or directional changes on a vertical plane. Width ( W ) adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) VO3 12W3 - prefix 7 1/8 (181) 4 (102mm) VO3 12W4 - prefix 7 3/8 (187) 5 (127mm) VO3 12W5 - prefix 7 5/8 (194) 6 (152mm) VO3 12W6 - prefix /8 (200) 3 (76mm) VO3 24W3 - prefix /8 (333) 4 (102mm) VO3 24W4 - prefix /8 (340) 5 (127mm) VO3 24W5 - prefix /8 (346) 6 (152mm) VO3 24W6 - prefix /8 (352) LD 30 3 (76mm) VO3 36W3 - prefix /8 (486) 4 (102mm) VO3 36W4 - prefix 19 3/8 (492) 5 (127mm) VO3 36W5 - prefix 19 5/8 (498) 28 6 (152mm) VO3 36W6 - prefix 19 7/8 (505)

13 Fittings VO90 90 Deg Vertical Outside Elbow Width ( W ) For 90 Deg. External corners or directional changes on a vertical plane. adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) VO9 12W3 - prefix 16 2/8 (413) 4 (102mm) VO9 12W4 - prefix 17 2/8 (438) 5 (127mm) VO9 12W5 - prefix 18 2/8 (464) 6 (152mm) VO9 12W6 - prefix 19 2/8 (489) 3 (76mm) VO9 24W3 - prefix 06, /8 (718) 4 (102mm) VO9 24W4 - prefix 12, /8 (743) 5 (127mm) VO9 24W5 - prefix 24, /8 (768) 6 (152mm) VO9 24W6 - prefix 31 2/8 (794) LD 3 (76mm) VO9 36W3 - prefix 40 2/8 (1022) VO60 4 (102mm) VO9 36W4 - prefix 41 2/8 (1048) 5 (127mm) VO9 36W5 - prefix 42 2/8 (1073) 6 (152mm) VO9 36W6 - prefix 43 2/8 (1099) 60 Deg Vertical Outside Elbow Width ( W ) For 60 Deg. External corners or directional changes on a vertical plane. adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) VO6 12W3 - prefix 12 2/8 (311) 4 (102mm) VO6 12W4 - prefix 12 5/8 (321) 5 (127mm) VO6 12W5 - prefix 13 1/8 (333) 6 (152mm) VO6 12W6 - prefix 13 4/8 (343) 3 (76mm) VO6 24W3 - prefix 06, /8 (575) 4 (102mm) VO6 24W4 - prefix 12, /8 (587) 5 (127mm) VO6 24W5 - prefix 24, /8 (597) 6 (152mm) VO6 24W6 - prefix 24 (610) LD 60 3 (76mm) VO6 36W3 - prefix 33 (838) 4 (102mm) VO6 36W4 - prefix 33 4/8 (851) 5 (127mm) VO6 36W5 - prefix 33 7/8 (860) 6 (152mm) VO6 36W6 - prefix 34 3/8 (873) 29

14 Fittings V Deg Vertical Inside Elbow Width ( W ) For 45 Deg. Internal corners or directional changes on a vertical plane. adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) V14 12W3 - prefix 10 (254) 4 (102mm) V14 12W4 - prefix 10 3/8 (264) 5 (127mm) V14 12W5 - prefix 10 6/8 (273) 6 (152mm) V14 12W6 - prefix 11 1/8 (283) 3 (76mm) V14 24W3 - prefix 06, /8 (470) 4 (102mm) V14 24W4 - prefix 12, /8 (479) 5 (127mm) V14 24W5 - prefix 24, /8 (489) 6 (152mm) V14 24W6 - prefix 19 4/8 (610) 45 VI30 3 (76mm) V14 36W3 - prefix 27 (838) 4 (102mm) V14 36W4 - prefix 27 3/8 (695) 5 (127mm) V14 36W5 - prefix 27 5/8 (702) 6 (152mm) V14 36W6 - prefix 28 (711) 30 Deg Vertical Inside Elbow LD For 30 Deg. Internal corners or directional changes on a vertical plane. Width ( W ) adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) V13 12W3 - prefix 7 1/8 (181) 4 (102mm) V13 12W4 - prefix 7 3/8 (187) 5 (127mm) V13 12W5 - prefix 7 5/8 (194) 6 (152mm) V13 12W6 - prefix 7 7/8 (200) 3 (76mm) V13 24W3 - prefix 06, /8 (333) 4 (102mm) V13 24W4 - prefix 12, /8 (340) 5 (127mm) V13 24W5 - prefix 24, /8 (346) 6 (152mm) V13 24W6 - prefix 13 7/8 (352) 3 (76mm) V13 36W3 - prefix 19 1/8 (486) 4 (102mm) V13 36W4 - prefix 19 3/8 (492) 5 (127mm) V13 36W5 - prefix 19 5/8 (498) 30 LD 30 6 (152mm) V13 36W6 - prefix 19 7/8 (505)

15 Fittings VI90 90 Deg Vertical Inside Elbow For 90 Deg. Internal corners or directional changes on a vertical plane. adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) V19 12W3 - prefix 16 2/8 (413) 4 (102mm) V19 12W4 - prefix 17 2/8 (438) 5 (127mm) V19 12W5 - prefix 18 2/8 (464) 6 (152mm) V19 12W6 - prefix 19 2/8 (489) 3 (76mm) V19 24W3 - prefix 06, /8 (718) 4 (102mm) V19 24W4 - prefix 12, /8 (743) 5 (127mm) V19 24W5 - prefix 24, /8 (768) 6 (152mm) V19 24W6 - prefix 31 2/8 (794) 3 (76mm) V19 36W3 - prefix 40 2/8 (1022) 4 (102mm) V19 36W4 - prefix 41 2/8 (1048) 5 (127mm) V19 36W5 - prefix 42 2/8 (1073) 6 (152mm) V19 36W6 - prefix 43 2/8 (1099) VI60 60 Deg Vertical Inside Elbow Width ( W ) For 60 Deg. Internal corners or directional changes on a vertical plane. adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) 3 (76mm) V16 12W3 - prefix 12 2/8 (311) 4 (102mm) V16 12W4 - prefix 12 5/8 (321) 5 (127mm) V16 12W5 - prefix 13 1/8 (333) 6 (152mm) V16 12W6 - prefix 13 4/8 (343) 3 (76mm) V16 24W3 - prefix 06, /8 (575) 4 (102mm) V16 24W4 - prefix 12, /8 (587) 5 (127mm) V16 24W5 - prefix 24, /8 (597) 6 (152mm) V16 24W6 - prefix 24 (610) 3 (76mm) V16 36W3 - prefix 33 (838) 60 4 (102mm) V16 36W4 - prefix 33 4/8 (851) 5 (127mm) V16 36W5 - prefix 33 7/8 (860) 6 (152mm) V16 36W6 - prefix 34 3/8 (873) 31

16 Fittings VT Vertical Tee Fitting adius Width Part No A in Width (mm) in (mm) Model no - Prefix in (mm) in (mm) 06 (152mm) VT prefix 24 (610) 18 (457) 09 (229mm) VT prefix 30 (762) 21 (533) VT prefix 36 (914) 24 (610) 18 (457mm) VT prefix 48 (1219) 30 (762) VT prefix 60 (1524) 36 (914) 30 (762mm) VT prefix 72 (1829) 42 (1067) VT prefix 84 (2134) 48 (1219) 06 (152mm) VT prefix 36 (914) 30 (762) 09 (229mm) VT prefix 42 (1067) 33 (838) VT prefix 48 (1219) 36 (914) 18 (457mm) VT prefix 60 (1524) 42 (1067) VT prefix 72 (1829) 48 (1219) 30 (762mm) VT prefix 84 (2134) 54 (1372) VT prefix 96 (2438) 60 (1524) 06 (152mm) VT prefix 48 (1219) 42 (1067) 09 (229mm) VT prefix 54 (1372) 45 (1143) VT prefix 60 (1524) 48 (1219) 18 (457mm) VT prefix 72 (1829) 54 (1372) VT prefix 84 (2134) 60 (1524) 30 (762mm) VT prefix 96 (2438) 66 (1676) VT prefix 108 (2743) 72 (1829) VS Vertical Support Fitting For Making right angle turns on the vertical plan. For branch to tray with narrower width than main tray, use reducers or consult factory. LD A Width ( W ) For 90 Deg. External corners or directional changes on a vertical plane. adius ( ) Load Depth (LD) Part No Width in Width (mm) in (mm) Model no - Prefix ( W ) in (mm) Width ( W ) 3 (76mm) VS 12W3 - prefix 16 2/8 (413) 4 (102mm) VS 12W4 - prefix 17 2/8 (438) 5 (127mm) VS 12W5 - prefix 18 2/8 (464) 6 (152mm) VS 12W6 - prefix 19 2/8 (489) 3 (76mm) VS 24W3 - prefix 06, /8 (718) 4 (102mm) VS 24W4 - prefix 12, /8 (743) 5 (127mm) VS 24W5 - prefix 24, /8 (768) 6 (152mm) VS 24W6 - prefix 31 2/8 (794) 3 (76mm) VS 36W3 - prefix 40 2/8 (1022) LD A A 4 (102mm) VS 36W4 - prefix 41 2/8 (1048) 5 (127mm) VS 36W5 - prefix 42 2/8 (1073) 32 6 (152mm) VS 36W6 - prefix 43 2/8 (1099)

17 Fittings HYL&HY Horizontal -Y- (Left & ight) For Making 45 Deg. angle turns on the same plan. For branch to tray with narrower width than main tray, use reducers or consult factory. Width ( W ) Type Width Width Part No A in (mm) Model no - Prefix in (mm) in (mm) 06 (152mm) HYL 06 - prefix 22 (552) 16 (413) 09 (229mm) HYL 09 - prefix 26 (660) 21 (543) Left Hand HYL 12 - prefix 30 (768) 27 (673) 18 (457mm) HYL 18 - prefix 39 (984) 37 (933) HYL 24 - prefix 47 (1200) 47 (1194) 30 (762mm) HYL 30 - prefix 56 (1416) 57 (1454) HYL 36 - prefix 64 (1632) 68 (1715) A 06 (152mm) HY 06 - prefix 22 (552) 16 (413) 09 (229mm) HY 09 - prefix 26 (660) 21 (543) HY 12 - prefix 30 (768) 27 (673) 45.0 ight Hand 18 (457mm) HY 18 - prefix 39 (984) 37 (933) HY 24 - prefix 47 (1200) 47 (1194) 71/4 30 (762mm) HY 30 - prefix 56 (1413) 57 (1454) AH HY 36 - prefix 64 (1632) 68 (1715) Adjustable Horizontal Elbow For changing the direction of a cable tray system at angles other than those provided by fixed elbows. Providing angular adjustment in a range 30 to 90. For angles less than 30 deg, Consult Factory. Width Width ( W ) Load Depth (LD) in (mm) Model no - Prefix in (mm) 06 (152mm) AH 06 - prefix 22 (552) 09 (229mm) AH 09 - prefix 26 (660) AH 12 - prefix 30 (768) 18 (457mm) AH 18 - prefix 39 (984) AH 24 - prefix 47 (1200) 30 (762mm) AH 30 - prefix 56 (1416) AH 36 - prefix 64 (1632) Width ( W ) 33

18 Fittings educers S Straight educer ight Hand educer L Left Hand educer For gradually reducing the size of tray both sides. For gradually reducing the size of tray from right side. For gradually reducing the size of tray from left side. W1 W2 W1 W2 W1 W (305 mm) 12 (305 mm) 12 (305 mm) S: Straight educer : ight Hand educer L: Left Hand educer Width ( W1) Width ( W2 )V Part No Part No Part No in Width(mm) in (mm) Model no - Prefix Model no - Prefix Model no - Prefix 06 (152mm) S prefix prefix L prefix 09 (229mm) S prefix prefix L prefix S prefix prefix L prefix 18 (457mm) S prefix prefix L prefix S prefix prefix L prefix 30 (762mm) S prefix prefix L prefix 06 (152mm) S prefix prefix L prefix 09 (229mm) S prefix prefix L prefix 30 (762mm) S prefix prefix L prefix 18 (457mm) S prefix prefix L prefix S prefix prefix L prefix 06 (152mm) S prefix prefix L prefix 09 (229mm) S prefix prefix L prefix S prefix prefix L prefix 18 (457mm) S prefix prefix L prefix 06 (152mm) S prefix prefix L prefix 18 (457mm) 09 (229mm) S prefix prefix L prefix S prefix prefix L prefix 06 (152mm) S prefix prefix L prefix 09 (229mm) S prefix prefix L prefix 09 (229mm) 06 (152mm) S prefix prefix L prefix

19 Connectors USC Universal Splice Connector EPC Expansion Plate Connector Supplied in Pairs and have hole pattern which match the tray system. Hardware to be ordered separately. For field installation drill 13/32 hole. Tighten with enough torque approx.(22 ft/lbs). Expansion plate provides one inch expansion or contraction of cable tray as per NEMA VE-1 Supplied in Pairs, Hardware to be ordered separately. Tighten lock nut just enough to allow movement along the slot. onding Jumper required, To be ordered separately (76 mm) USC3 - M/F 3 (76 mm) EPC3 - M/F 4 (102 mm) USC4 - M/F 4 (102 mm) EPC4 - M/F 5 (127 mm) USC5 - M/F 5 (127 mm) EPC5 - M/F 6 (152 mm) USC6 - M/F 6 (152 mm) EPC6 - M/F VAC Vertical Adjustable Connector HAC Horizontal Adjustable Connector equired to provide change in elevation where standard vertical fittings do not apply. Supplied in Pairs,Hardware to be ordered separately. onding Jumper required, To be ordered separately. equired to provide change direction in horizontal plan where standard horizontal fittings do not apply. Supplied in Pairs,Hardware to be ordered separately. onding Jumper required, To be ordered separately. 3 (76 mm) VAC3 - M/F 4 (102 mm) VAC4 - M/F 5 (127 mm) VAC5 - M/F 3 (76 mm) HAC3 - M/F 4 (102 mm) HAC4 - M/F 5 (127 mm) HAC5 - M/F (305MM) 12 (305MM) 6 (152 mm) VAC6 - M/F 6 (152 mm) HAC6 - M/F ACC 90 Deg Angle Connector SDC Step Down Connector equired to connect cable trays for 90 Deg. Direction in limited radius area or to connect to panel or box. Supplied in Pairs. Hardware to be ordered separately equired to connect cable trays of different side rail Height. Supplied in Pairs. Hardware to be ordered separately LD1 3 (76 mm) USC3 - M/F 3 (76 mm) EPC3 - M/F 4 (102 mm) USC4 - M/F 4 (102 mm) EPC4 - M/F 5 (127 mm) USC5 - M/F 5 (127 mm) EPC5 - M/F LD2 6 (152 mm) USC6 - M/F 3 6 (152 mm) EPC6 - M/F 35

20 Accessories PC ranch Pivot Connector EC lind End Plate equired to form branch from cable tray run at any point. Supplied in Pairs,Hardware to be ordered seperately. onding Jumper required, To be ordered seperately. equired to form closure for dead end of cable tray. Hardware to be ordered separately. 3 (76 mm) PC3 - M/F 4 (102 mm) PC4 - M/F 5 (127 mm) PC5 - M/F 6 (152 mm) PC6 - M/F 3 (76 mm) EC3-W-M/F 4 (102 mm) EC4-W-M/F 5 (127 mm) EC5-W-M/F 6 (152 mm) EC6-W-M/F On order state : On order state : W : Denotes Cable Tray Width PC educing Plate Connector OC Offset educing Connector equired to join cable trays with different widths Supplied in Pairs,Hardware to be ordered separately. equired for offset reduction (left hand or right hand) of defferent width cable trays. Supplied in Pairs,Hardware to be ordered separately. 3 (76 mm) PC3-W-M/F 4 (102 mm) PC4-W-M/F 5 (127 mm) PC5-W-M/F 3 (76 mm) OC3-W-M/F 4 (102 mm) OC4-W-M/F 5 (127 mm) OC5-W-M/F Left Hand eduction 6 (152 mm) PC6-W-M/F 6 (152 mm) OC6-W-M/F On order state : W : Denotes Width eduction On order state : W : Denotes Width eduction ight Hand eduction TC Tray To ox Connector DOP Drop Out Plate equired to fix the end of cable tray distribution box. Hardware to be ordered separately. equired to exit cables from cable tray on round smooth piece to prevent damage of cable insulation. end radius is 4 (102 mm). Can be fixed on any rung along the tray. 3 (76 mm) TC3-W-M/F 4 (102 mm) TC4-W-M/F 5 (127 mm) TC5-W-M/F 6 (152 mm) TC6-W-M/F Catalogue No DOP-W-MIF 36 On order state : W : Denotes Cable Tray Width On order state : W : Denotes Cable Tray Width

21 Accessories SS arrier Strip Straight Width Load Depth (LD) in (mm) 3 (76mm) 4 (102mm) 5 (127mm) 6 (152mm) Part No SS3-M/F SS4-M/F SS5-M/F SS6-M/F LD SHF arrier Strip Horizontal Fitting Load Depth (LD) in (mm) 3 (76mm) 4 (102mm) 5 (127mm) 6 (152mm) Part No SHF3-M/F SHF4-M/F SHF5-M/F SHF6-M/F LD SVF adius ( ) in Width (mm) Load Depth (LD) in (mm) arrier Strip Vertical Fitting Part No 3 (76mm) SVF-312-M/F 4 (102mm) SVF-412-M/F 5 (127mm) SVF-512-M/F 6 (152mm) SVF-612-M/F 3 (76mm) SVF-324-M/F 4 (102mm) SVF-424-M/F 5 (127mm) SVF-524-M/F 6 (152mm) SVF-624-M/F 3 (76mm) SVF-336-M/F 4 (102mm) SVF-436-M/F 5 (127mm) SVF-536-M/F 6 (152mm) SVF-636-M/F SSC arrier Strip Clamp Assembly Load Depth (LD) in (mm) 3 (76mm) 4 (102mm) 5 (127mm) 6 (152mm) Part No SSC3-M/F SSC4-M/F SSC5-M/F SSC6-M/F 37

22 Ladder Accessories CHS Connector Hardware HDC Hold Down Clamp EGC Expansion Guide ibbed neck screw with Phillips slot. Size: 3/8 Dia. Nut with serrated face,no washer required. For use with all type of ladders Supplied in Pairs. Hardware, 3/8, to be ordered separately For use with all type of ladders Supplied in Pairs. Hardware, 3/8, to be ordered separately 2" 1 ½ " Item Catalogue No 7/16 Dia. Screw + Nut CHS-M/F Catalogue No Catalogue No On order state : GS : Electro galvanized HG: Hot dip Galvanized SS6: Stainless Steel 316 SS4: Stainless Steel 304 HDC-M/F On order state : EGC-M/F On order state : IDC Internal Hold Down VHC Vertical Hold Clamp IHC I-eam Hold Clamp For use mainly with through type tray and also for holding ladder from inside. Supplied in Pairs. Hardware, 3/8, to be ordered separately For use with Vertical installation of cable ladder. Supplied in Pairs. Hardware For Tray attachment 3/8, and 1/2 support hardware to be ordered separately For use on I-eam structure without drillings Supplied in Pairs. Hardware Included emove upper hardware to use as guide clamp 3 (76 mm) IDC3 - M/F 4 (102 mm) IDC4 - M/F 5 (127 mm) IDC5 - M/F Catalogue No VHC-M/F IHC-M/F 6 (152 mm) IDC6 - M/F J onding Jumper GWC Ground Wire Clip AGC AL.Ground Clamp For use to maintain electrical continuity to ground, to be used with expansion and adjustable connectors. For use to hold to tray side rail one or two bare copper or aluminum coductors Supplied in pieces. Hardware For Tray attachment 3/8 to be ordered separately For use to hold to tray side rail additional grounding coductors Conductor size: no. 6 to 250 MCM. Hardware included. Material is aluminum extruded. JI Type Size & AMP Catalogue No. 38 JS JI 600A. JS A. JS-16 1/0 (800 A) JI - 8 4/0 (1600 A) JI - 16 Cond. Size Catalogue No no. 1 to 2/0 GWC - 1 3/0 to 4/0 GWC - 2 Cond. Size no. 6 to 250 MCM Catalogue No AGC

23 Straight Covers A wide variety of covers which can be used horizontal and vertical runs to provide protection for cables installed in cable trays against environmental effects, sunlight and dirt. All covers are designed and fabricated to meet indoor and outdoor applications. Straight covers supplied are 10 and 12 ft. long. All standard cover fittings are flat solid type. Material : Finishes : (H) Hot rolled Steel sheet : to ASTM A 36 (HDG): Hot Dip Galvanized To ASTM A123(S EN1461) (PG) Pregalvanized Steel: to ASTM A-653 G90 (ZP): Zinc Plating To ASTM 633. (AL) Aluminum : AA H14 (EP): Epoxy Painted. (SS) Stainless Steel : to ASTM A240 (PC): Electrostatic Industrial Powder Coating. (Type 304 & 316) SFT Solid Flat Cover SFG Solid Flanged Cover LFT Louvered Flat Cover LFG Louvered Flanged Cover PFT Peaked Flat Cover PFG Peaked Flanged Cover Straight Covers Ordering Way : FIN SFT AL Ladder Type Name Class Width Length Material/Finish. FIN : Flange Inside FOT : Flange Outside SFT SFG LFT LFG PFT PFG 152 mm (06 ) 229 mm (09 ) 305 mm (12 ) 457 mm (18 ) 610 mm (24 ) 762 mm (30 ) 914 mm (36 ) 3.0 mtr (10 ) 3.7 mtr (12 ) PG: Pre galvanized Steel HG: Hot Dip Galvanized AL: Aluminum S4: Stainless Steel 304 S6: Stainless Steel 316 CA: Corten-A Steel HP: Hot Dip Galvanized & Powder Coated 39

24 Ladder Cover Clamps Quantity of Standard Cover Clamps equired: Straight Section 60 or pcs. Horizontal/Vertical ends...4 pcs. Crosses...8 pcs. Material : (H) Hot rolled Steel sheet : to ASTM A 36 (PG) Pregalvanized Steel: to ASTM A-653 G90 (AL) Aluminum : AA H14 (SS) Stainless Steel : to ASTM A240 (Type 304 & 316) Straight Section 120 or pcs. Tees...6 pcs. Finishes : (HDG): Hot Dip Galvanized To ASTM A123(S EN1461) (ZP): Zinc Plating To ASTM 633. (EP): Epoxy Painted. (PC): Electrostatic Industrial Powder Coating. FSC Fixing screws FCC Cover Clamp Screws, self-drilling and lapping. provide economical cover hold-down for trays with inturned flanges. ecommended installation:8 screws for each 12 foot section. Zinc plated Steel. For indoor Installation Only. Cov DCC Catalogue No FSC-M/F Double Connector Clamp ecommended for outdoor service Insert Tray Width Catalogue No WCC FCC-M/F Side ail Wraparound Cover Clamp ecommended for outdoor service Insert Tray Width 3 (76 mm) DCC3 - M/F 4 (102 mm) DCC4 - M/F 5 (127 mm) DCC5 - M/F 6 (152 mm) DCC6 - M/F Insert tray width 3 (76 mm) WCC3 - M/F 4 (102 mm) WCC4 - M/F 5 (127 mm) WCC5 - M/F 6 (152 mm) WCC6 - M/F CC aised Cover Clamp WPC Wraparound Peaked Cover Clamp Specify gap of 1, 2, 3 or 4. ecommended for outdoor service Insert Tray Width Catalogue No CC-M/F 3 (76 mm) WPC3 - M/F 4 (102 mm) WPC4 - M/F 5 (127 mm) WPC5 - M/F 6 (152 mm) WPC6 - M/F 40