PORTABLE CONCRETE SAWS

Transcription

1 Core Cut Saws Whatever It Takes PORTABLE CONCRETE SAWS Light Weight and Reliable Pg. 3

2 CC1000 GREEN CONCRETE SAW The ultra light saw that cuts decorative and green concrete joints Center cut design - Better tracking into an existing cut and easy to keep the cut straight Quick, easy & light weight (90 lbs.) Power transmission to blade drive is via 2 molded notch 3VX premium belts - for better cutting performance and longer belt life. Portable Concrete Saws 1/8 inch steel frame Cutting depth up to 2-1/4" with 8 inch blade Front and rear pointers Upcut design for a cleaner cut Cyclone air cleaner for increased engine longevity 1" arbor with greaseable bearings Adjustable blade alignment Dust diverter keeps saw line visable CC1000 Green Concrete Saw Model No. Engine Type P/N Cat. No. Blade Capacity Uncrated Wt.** CC1055H 5.5 HP Honda " 90 lbs. CC1025E 2.5 HP Electric 1PH - 110V/230V " 90 ** Add 30 lbs. for crated weight. Pg. 4 CC1000 Specifications Maximum Depth of Cut: 2-1/4" Blade Shaft RPM: 6,100 Blade Shaft Diameter: 1" Arbor Size: 1" Diameter Front Wheels: 3" x 2" x 3/4" Rear Wheels: 5" x 2" x 3/4" Heavy Duty Orange Blades for Green Concrete GCS100H Soft Bond GCS200H Medium Bond GCS300H Hard Bond SIZE Cat. No. Cat. No. Cat. No. 8" X.100 X " X.125 X " X.250 X CC1000 Dimensions A Saw Height 34-1/2" B Min Length, Pointer Up 26-1/2" C Max Length, Pointer Down 56" D Pointer Extension 18" E Frame Width 10" F Frame Length 23-1/2" G Saw Width 14-1/2" H Front Axle Center Length 6-1/2" I Rear Axle Center Length 7" J Wheel Base Length 11" Blade Shaft Max Height 4-7/8"

3 CC1200 CONCRETE SAW Our Most Economical Walk Behind Concrete Saw Heavy Duty Design Sturdy handles with no slack. Doesn t rattle like other adjustable handles. Slip-on Blade Guard Depth indicator 6-5/8" maximum cutting depth CC1200 CC1200 Push Push Saws Saws With With Hand Wheel Screw Feed Feed Raise/Lower System System Model No. Engine Type Part No. Cat. No. Blade Capacity Uncrated Wt.** CC1209RS-14 9 HP Robin-Subaru " 205 lbs. CC1209RS-18 9 HP Robin-Subaru " 205 CC1209HS-14 9 HP Honda " 210 CC1213HS HP Honda " 210 CC1213HS HP Honda " 210 CC1200 Specifications Maximum Depth of Cut with 14" Blade: 4-5/8" Maximum Depth of Cut with 18" Blade: 6-5/8" Blade Shaft RPM: 2,600 Blade Shaft Diameter: 1-1/4" Arbor Size: 1" Diameter with Single Drive Pin CC1200 Options Description Part No. Cat. No. 5 Gal. Water Tank Kit Extra Blade Guard 14" Extra Blade Guard 18" ** Add 40 lbs. for crated weight. CC1200 Dimensions A Saw Height 38" B Min length Pointer Up, Handle Down 31" C Max length Pointer Down, Handle Up 62" D Handle Extension 11" E Frame Width 13-1/2" F Frame Length 24" G Saw Width 22" H Front Axle Center Length 9-1/2" I Rear Axle Center Length 17" J Wheel Base Length 13" Blade Shaft Max Height 10-1/2" Choice of Robin-Subaru (9 HP) or Honda (9 or 13 HP) engine 18" Maximum Blade Capacity Left or right hand sawing Portable Concrete Saws Pg. 5

4 CC1300XL CONCRETE SAW The Portable Concrete Saw Built Extra Tough Extra sturdy handles adjustable to 4 positions for precise control. Doesn t rattle like other adjustable handles. CC1309HSXL with 13 HP Honda engine Portable Concrete Saws Available as an optional 10 HP electric saw with 20" blade capacity (on an extended frame) Available with Honda gas engine or with optional 5 HP electric motor (1 or 3 phase) Left or right hand sawing Through rear axle for added strength 6-5/8" maximum cutting depth with 18" blade guard Solid, sealed self aligning blade shaft ball bearings Pg. 6

5 CC1300XL SPECIFICATIONS Easy turning and quick acting handwheel raise and lower making handling even easier. Smooth Power Delivery to Blade Shaft Power transmission to blade drive is via 3 molded notch 3VX premium belts - not 2, like some of our competitors, resulting in better cutting performance and longer belt life. Multi Spray Blade Coolant System Blade coolant is delivered from an innovative dual multi-spray water tube system which gets coolant to both sides of the blade from the arbor to the top of the blade. CC1305E1XL Electric Saw CC1300XL CC1300-XL Push Push Saws Saws With With Hand Hand Wheel Wheel Screw Feed Raise And Lower System Model No. Engine Type P/N-14" Model Cat No. 14" P/N-18" Model Cat. No. 18" Uncrated Wt.** CC1309HS-XL 9 HP Honda lbs. CC1313HS-XL 13 HP Honda CC1305E1-XL 5 HP Lincoln - 1 PH Electric CC1305E3-XL 5 HP Lincoln - 3 PH Electric HP - 3 PH 460V Electric P/N. - 20" Gd. Cat. No. 20" Gd. CC1310E3-20-XL with switchbox and 20" Guard ** Add 40 lbs. for crated weight. Portable Concrete Saws CC1300XL Options Description P/N Cat. No. Water Tank Kit* (5 gallon) Extra Blade Guard 14" Extra Blade Guard 18" Catalytic Muffler 13 HP Honda Extended Blade Shaft Kit for up to 1" spacing *For dust suppression when dry cutting only Water tank kit not available on electric saw models. CC1300XL Specifications Maximum Depth of Cut with 14" Blade: 4-5/8" Maximum Depth of Cut with 18" Blade: 6-5/8" Maximum Depth of Cut with 20" Blade: 7-5/8" Blade Shaft RPM: 2,600 Blade Shaft Diameter: 1-1/4" Arbor Size: 1" Diameter with Single Drive Pin CC1300XL Dimensions A Saw Height 40" B Min length Pointer Up, Handle Down 31-1/4" C Max length Pointer Down, Handle Up 60" D Handle Extension 13-1/2" E Frame Width 12-3/4" F Frame Length 23-5/8" G Saw Width 22-3/4" H Front Axle Center Length 7-1/2" I Rear Axle Center Length 16-3/4" J Wheel Base Length 12-5/8" Blade Shaft Max Height 10-1/2" Diamond Products Customer Service (800) Pg. 7

6 BLADE SHAFT RPMS CC1000 Blade Size Blade RPM 8" 6,100 CC1200 and CC1300XL Blade Size Blade RPM 14" and 18" 2,600 Concrete Saws Pg. 8 CC1800 Blade Size Blade RPM 14" and 20" 2,600 CC2500 Gas Models Blade Size Blade RPM 14" 2,625 20" 2,625 26" 2,025 Diesel/Hydraulic Models 14" 2,650 20" 2,650 26" 1,900 Electric Models 14" 2,625 20" 2,625 26" 2,275 CC3500 Gas Models (CC3535) Blade Size Blade RPM 14" 3,000 20" 2,500 26" 1,900 30" 1,650 Electric Models (CC3530E & CC3520E) Blade Size Blade RPM 14" 3,050 20" 2,350 26" 1,800 30" 1,550 CC3700 Gas Models Blade Size Blade RPM 14" 2,900 20" 2,450 26" 1,950 30" 1,650 36" 1,400 Diesel Models 14" 3,000 20" 2,475 26" 1,900 30" 1,650 36" 1,400 Electric 25/30 HP Models 14" 3,050 20" 2,350 26" 1,800 30" 1,550 36" 1,375 Electric 40 HP Models 20" 2,450 26" 2,000 30" 1,700 36" 1,400 CC4000D Gas Multi Speed Models Blade Size Blade RPM 14" 2,875 20" 2,400 26" 2,000 30" 1,675 Gas Single Speed Models Blade Size Blade RPM 14" 3,000 20" 2,300 26" 1,925 30" 1,700 Electric Dual Speed Models Blade Size Blade RPM 14" 2,875 20" 2,325 26" 2,050 30" 1,675 CC6500 Gas Models Blade Size Blade RPM 14" 2,900 20" 2,450 26" 1,950 30" 1,575 36" 1,425 42" 1,050 48" 960 Electric Models 20" 2,450 26" 2,000 30" 1,700 36" 1,400 42/48" 1,075 CC6560XLS Blade Size Blade RPM 14" 2,900 20" 2,400 26" 2,150 30" 1,800 36" 1,500 CC7100 Blade Size Blade RPM 14" 2,900 20" 2,425 26" 1,950 30" 1,600 36" 1,325 42" 1,050 CC7200 Diesel and Gas Models Blade Size Blade RPM 26" 1,925 30" 1,500 36" 1,025 42" 1,025 48" " 775 Electric Models Blade Size Blade RPM 26" 1,600 30" 1,600 36" 1,050 42" 1,050 48" " 750 CC8000 Blade Size Blade RPM 14" 3,000 20" 2,450 26" 1,950 30" 1,650 36" 1,400 42" 1,050 48" " 775 CC120 Blade Size Blade RPM 36" 1,400 42" 1,050 48" " " " " 500 Diamond Products Customer Service (800)

7 Medium Concrete Saws Whatever It Takes MEDIUM CONCRETE SAWS Medium Saws with Large Productivity Pg. 9

8 CC1800 SERIES CONCRETE SAW Large Saw Features in a Portable Saw Screw feed raise and lower mechanism Medium Concrete Saws Handle adjusts to saw operators height Left or right hand sawing Available with push or hydrostatic transmission choices Variety of power options in gasoline, electric or hydraulic up to 20 HP Self aligning blade shaft bearings Available with choice of 14" or 20" blade guard 7-5/8" cutting depth with 20" guard Pg. 10 Blade drive is via 4 belts on 16 HP models and up. 14 HP models and below have 3 belts Available with a 7.5 or 10 HP electric motor

9 CC1800 SPECIFICATIONS CC1800 Control Panel (remote throttle, choke and ignition switch are only available on 20 HP models) CC1800 PUSH Saws Model No. Engine Type P/N - 14" Model Cat. No. - 14" P/N - 20" Model Cat. No. - 20" Uncrated Wt.** CC1875E1-P 7.5 HP Baldor - 1 PH - 230V Electric lbs. CC1810E3-P 10 HP Baldor - 3 PH Electric * CC1813H-P 13 HP Honda CC1816BV-P 16 HP Briggs Vanguard CC1818HY-P 18 HP Danfoss Hydraulic * Specify 230V or 460V. 575V motors available on request. 50 cycle motors also available. + Specify available input flow (GPM). 25 PSI maximum. * Specify 230V or 460V. 575V or 50 cycle motors available on request. Electric start + Specify available input flow (GPM) 25 PSI maximum. Includes remote cyclone air cleaner CC1800 Specifications Maximum Depth of Cut With 14" Blade: 4-5/8" Maximum Depth of Cut With 20" Blade: 7-5/8" Blade Shaft RPM: 2600 Blade Shaft Diameter: 1-1/4" Arbor Diameter: 1" with single drive pin Blade Shaft Drive: 3 belt through 13 HP, 4 belt 16 HP and up Blade Mounting: Right or left Blade Raise and Lower: Precision screw feed Front Wheel Dimensions: 5" x 1-1/2" x 3/4" Rear Wheel Dimensions: 6" x 1-1/2" x 5/8" Handle Bars: Adjustable height Transmission: Eaton Model 6 or push Drive Speed: 0-80 feet per minute Fuel Capacity: 2 gallons Electric Start: Standard on 20 HP models Low Oil Alert: Standard Tach/Hour Meter: Standard on 20 HP models ** Add 40 lbs. for crated weight. CC1800 SELF-PROPELLED Saws Model No. Engine Type P/N - 14" Model Cat. No. - 14" P/N - 20" Model Cat. No. - 20" Uncrated Wt.** CC1875E1-S 7.5 HP Baldor- 1 PH- 230V Electric lbs. CC1810E3-S 10 HP Baldor - 3 PH Electric * CC1813H-S 13 HP Honda CC1816BV-S 16 HP Briggs Vanguard CC1818HY-S 18 HP Danfoss Hydraulic CC1820H-S 20 HP Honda ** Add 40 lbs. for crated weight. Medium Concrete Saws CC1800 Options Description P/N Cat. No. Electric Water Pump (Electric start only) Water Tank Kit * (5 gallon) Frame Lift Frame Lift for CC1813H Saw Only Tach/Hour Meter (displays engine RPM) Weight Kit ** (26 pounds) Extra Blade Guard 14" Extra Blade Guard 20" Catalytic Muffler for 13 HP Honda Catalytic Muffler for 20 HP Honda Extended Blade Shaft Kit for up to 1" spacing * For dust suppression when dry cutting only. Frame Lift must also be ordered to allow use of water tank kit on all saw models under 20HP. (Not available on electric saw models). Standard on all 20 HP model saws. ** Standard on all saws with 20" blade capacity and all saws over 15 HP. Standard on all electric saw models CC1800 Dimensions A Saw Height with Handlebar 37-1/2" B Min Length Pointer Up 36" C Max Length Pointer Down 72" D Saw Height w/o Handlebar 33-3/4" E Frame Width 16" F Frame Length 30-5/8" G Saw Width 22-3/8" H Front Axle Center Length 12" I Rear Axle Center Length 12" J Wheel Base Length 15-7/8" Blade Shaft Max Height 11-1/2" Pg. 11

10 CC2500 SERIES CONCRETE SAW Delivers the Power of a Large Saw with the Compactness and Economy of a Small One! Economical screw feed raise and lower mechanism standard or with optional power raise/lower assembly Variety of gas, diesel, electric or hydraulic engine options up to 27 horsepower Medium Concrete Saws Positive gear drive to rear axle via Eaton hydrostatic transmission Now offered with hydraulic raise/lower on all models Maximum cutting depth 10-3/8" with 26" guard 2 position tilt handle bars Choice of 14", 20" or 26" slip-on blade guards Large 5-Gallon fuel capacity for longer sawing between refills Pg. 12 Rigid high strength 3/16" steel box frame with heavy bar reinforcement 1-1/2" diameter bladeshaft with bearings that are greasable from the top of the frame

11 CC2500 SPECIFICATIONS CC2500 Control Panel (shown with optional raise/lower control button) Cutting Depth Chart Blade Diameter 14" 20" 26" Cutting Depth 4-3/8" 7-3/8" 10-3/8" CC2500 Saws Model No. Engine Type P/N Cat. No. Blade Capacity Uncrated Wt.* CC2515E HP Leeson Electric ** " 700 lbs. CC2515E HP Leeson Electric ** " 710 CC2515E HP Leeson Electric ** " 720 CC2520H HP Honda " 600 CC2520H HP Honda " 610 CC2520H HP Honda " 620 CC2524H HP Honda " 590 CC2524H HP Honda " 600 CC2524H HP Honda " 600 CC2525HY HP Hydraulic " 600 CC2525HY HP Hydraulic " 600 CC2525HY HP Hydraulic " 600 CC2527KC HP Kohler Command " 600 CC2527KC HP Kohler Command " 610 CC2527KC HP Kohler Command " 620 ** Specify 230V or 460V. 575V motors available upon request. 50 cycle motors also available (includes motor switch box). Includes remote cyclone air cleaner. Requires PSI maximum input flow. CC2500 Specifications Maximum Depth of Cut: 10-3/8" Blade Shaft Diameter: 1-1/2" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning pillow block ball Blade Shaft Drive: 4 belt through 25 HP, 5 belt for 27 HP Blade Mounting: Right or left Blade Raise and Lower: Precision ACME screw feed standard, power raise/lower assembly optional Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on Front Wheel Dimensions: 6" x 2" x 1" Rear Wheel Dimensions: 8" x 2" x1 " Handle Bars: Tilt Transmission: Eaton Model 6 Drive Speed: feet per minute Fuel Capacity: 5 gallons Electric Start: Standard Tach/Hour Meter: Standard Low Oil Alert: Standard Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Frame Lift: Standard *add 70 pounds for crated weight. Medium Concrete Saws CC2500 Options Description Part No. Cat. No. Water Safety Switch * Water Pump (electric) * Spot Light * Electric Raise/Lower Assy. for Gas/Diesel Saw Electric Raise/Lower Assy. for Electric Saw ** Electric Raise/Lower Assy. for Hydraulic Saw ** Hydraulic Raise/Lower Assy. for Gas/Diesel Saw Hydraulic Raise/Lower Assy. for Electric Saw ** Hydraulic Raise/Lower Assy. for Hydraulic Saw ** Extended Blade Shaft Kit for spacing blades 3/4" to 1-1/2" Extended Blade Shaft Kit for spacing blades 1-1/2" to 2-1/4" Catalytic Muffler for 20 HP Honda Engine Extra Slip-On Blade Guards: 14" Capacity " Capacity " Capacity * Not available on electric saw models (CC2515E) or hydraulic saw models (CC2525HY) without Power Raise/Lower Assembly. ** Includes battery and alternator. CC2500 Dimensions A Saw Height 47-1/2" B Min Length Pointer Up, Handle In 47-1/2" C Max Length Pointer Down, Handle Out 107-1/2" D Handle Extension 24" E Frame Width 20" F Frame Length 38" G Saw Width 26-1/2" H Front Axle Center Length 15-1/2" I Rear Axle Center Length 17-3/4" J Wheel Base Length 20" Blade Shaft Max Height 14-1/2" Crated Saw Dimensions: 52" L x 34" W x 55" H Pg. 13

12 Whatever It Takes LARGE CONCRETE SAWS Efficient and Powerful. Pg. 14

13 LARGE SAW STANDARD FEATURES CORE CUT's one hand sawing control has raise/lower buttons conveniently located on forward/reverse speed control lever. Drive speed is infinitely adjustable up to 200 FPM forward or reverse. CORE CUT super reinforced large saw frames have the highest torsional strength in the industry giving you the best life and performance you can get from your diamond blades. These closed box frames decrease buildup of slurry and debris on engine and drive components. Engine weight is positioned over the blade for superior balance and maneuverability and improved straight line sawing. Hydrostatic Transmissions We use ultra high strength steel for our turned, ground and polished blade shaft, giving better blade balance and reduced blade vibration. Our quick release blade flanges allow the saw to be backed away from the cut if the blade is jammed or pinched in the cut. Dual flanges allow left or right hand sawing. We use only the best self-aligning, heavy duty, double concave roller bearings instead of inexpensive ball bearings for our blade shafts for greatly extended bearing life. Our four stage dry air cleaner gives your engine the best possible protection to ensure long service life. It has an inner filter to safeguard your engine in the event your outer filter is torn or damaged. Our handle bars can be repositioned for extra leverage when sawing with larger diameter blades or for easier maneuverability when positioning saw. Sundstrand transmission Eaton transmission CC3500 saw comes standard with Sundstrand- Sauer transmission which have direct chain drive to rear axle. CC3700, CC6500 and CC6560XLS are available with a Sundstrand- Sauer or Eaton transmission. CC4000D comes standard with a Peerless differential and Eaton transmission. CC7100 and CC7200 are available only with the Eaton transmission. Eaton transmissions have an increased pitch gear tooth for longer gear life and gear drive to rear axle. Standard CORE CUT control panel features include ammeter, hour meter, oil pressure gauge*, adjustable cutting depth indicator, throttle, choke, ignition switch and emergency stop button. These and other optional controls/switches are highly visible and accessible at console height. Vernier throttle control allows fast or fine speed adjustment with friction lock to maintain setting. Depth stop control limits depth of cut to any pre-selected setting. Operating and safety instructions are clearly marked on long life Lexan decals. *For 65 HP Wisconsin engine only Diamond Products Customer Service (800) Pg. 15

14 LARGE SAW OPTIONS Our Oil Cooler runs your 65 HP engine oil through an oil radiator which is chilled with blade water prior to cooling the blade. The result is a cooler, smoother running engine with higher output horsepower during hot weather. Oil cooler kit * Fram PH8A replacement filter * For Wisconsin 65 HP engines only Add a Spotlight for late afternoon or night sawing. Spotlight Kit CORE CUT large saws are available with optional Magnetic Spot Light. The easy to install magnetic spot light provides added visibility for late afternoon or night sawing. 42" - 48" Conversion Kit (for use on CC6500 Saws only) Kit converts CC6500 model concrete saw into either a high production 42" or 48" blade capacity saw. Can cut on both sides. Includes Blade Guard. Gas Electric 42" Blade Capacity Conversion Kit " Blade Capacity Conversion Kit Get free wheeling capability for your Sundstrand propelled saws with our Free Wheeling Clutch. Not necessary with Eaton transmissions. Free Wheeling Clutch (CC3500) (CC3700, CC6500 and CC6560XLS) Magnetic Spot Light Diamond Products Customer Service (800) Our Lowering Speed Metering Valve lets you make quick adjustments to your saws lowering speed to suit operator needs. Lowering Speed Metering Valve Water Safety Switch automatically shuts off engine when water flow is not sufficient to protect blade. Water Safety Switch (gas saws) Water Safety Switch (diesel saws) Pg. 16

15 LARGE SAW OPTIONS Blade Guards Optional slip-on and bolt-on blade guards ranging from 14" all the way to 54" are available with our large concrete saws. Rectangular Tapered Size/Blade Guard Type Width Mount Style Mount Style* 14" Capacity Slip-on Blade Guard 3-3/8" " Capacity Slip-on Blade Guard 3-3/8" " Capacity Slip-on Blade Guard 3-3/8" " Capacity Slip-on Blade Guard 3-3/8" " Capacity Bolt-on Blade Guard 3-3/8" " Capacity Bolt-on Blade Guard 3" " Capacity Bolt-on Blade Guard 3" " Capacity Bolt-on Blade Guard 3" * Tapered Mount Style for CC6560XLS only. Rectangular Mount Style Blade Guard Tapered Mount Style Blade Guard Rectangular Mount Style Tapered Mount Style All of our large saws have heavy-duty, hinged slip-on guards, for easy and fast access to your blades. Our multi-spray water system insures maximum water coverage of various blade sizes and reduces risk of blade damage due to clogged water tubes. Separate left and right side water control valves at console height allow easy sawing on either side of saw. Our Shaft Tachometer gives you an accurate readout of your saws blade shaft RPM. No more guessing if you have the correct speed for the size blades you are running. Shaft Tachometer (Shaft tachometer is standard on CC4000D, CC6560XL/XLJ, CC7100, CC7200 & CC8000) Large Saw Parking Brake (available on CC3500, CC3700, CC6500, CC6500XLS, CC7100 and CC7200) Electric Diaphragm Water Pump maintains constant water pressure. Electric Diaphragm Water Pump Pg. 17

16 CC3500 SERIES CONCRETE SAW 35 HP Service Saw Utilizes many of the same heavy-duty components we use on our bigger saws Fits through a 30" door! Choice of 14" through 30" blade guards Ideal for municipalities and rental stores Strongest frame on the market Maximum cutting depth 12-3/8" with 30" guard Available with a 20 HP or 30 HP electric motor. Features Wisconsin 35 HP gasoline engine Pg. 18 CORE CUT large saws feature convenient one hand saw control.

17 CC3500 SPECIFICATIONS CC3500 Control Panel (shown with optional shaft tachometer and lowering speed metering valve) Cutting Depth Chart Blade Diameter 14" 20" 26" 30" Cutting Depth 4-3/8" 7-3/8" 10-3/8" 12-3/8" CC3500 Saws Model No. Engine Type Part No. Cat. No. Blade Capacity Uncrated Wt.* CC HP Wisconsin " 1,090 lbs. CC HP Wisconsin " 1,100 CC HP Wisconsin " 1,110 CC HP Wisconsin " 1,120 CC3530E HP Lincoln Electric (460v) " 1,035 CC3530E HP Lincoln Electric (460v) " 1,045 CC3530E HP Lincoln Electric (460v) " 1,055 CC3530E HP Lincoln Electric (460v) " 1,065 CC3520E HP Baldor Electric * " 1,005 CC3520E HP Baldor Electric * " 1,015 CC3520E HP Baldor Electric * " 1,025 CC3520E HP Baldor Electric * " 1,035 * Specify 230V or 460V. 575V or 50 cycle motors available on request. Includes motor starter switchbox. Quick-release bladeshaft/flange, slip-on blade guards and double concave roller bearings are standard on all CC3500 saws. CC3500 Specifications Maximum Depth of Cut: 12-3/8" Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 6 belt Blade Mounting: Right or left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on Front Wheel Dimensions: 6" x 2" x 1" Rear Wheel Dimensions: 8" x 2-1/2" x 1-1/4" Handle Bars: Tilt Transmission: Sundstrand-Sauer Drive Speed: feet per minute Air Filter: 4 stage Fuel Capacity: 6 gallons Electric Start: Standard High Temperature Shut-Off: Standard Hour Meter: Standard Tachometer: Optional Amp Meter: Standard Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Frame Lift: Standard Telescoping Front Pointer: Standard * add 70 pounds for crated weight CC3500 Options Description P/N Cat. No. Free Wheeling Clutch * Water Safety Switch Water Pump (electric) Parking Brake Spot Light Magnetic Spot Light Vertical Muffler Shaft Tachometer Lowering Speed Metering Valve Soft Start Controller Add On ** Extended Blade Shaft Kit for spacing blades 3/4" to 1-1/2" Extended Blade Shaft Kit for spacing blades 1-1/2" to 2-1/4" Extra Slip-On Blade Guards: 14" Capacity " Capacity " Capacity " Capacity * Standard on all electric saw models. ** For electric saws-factory installed CC3500 Dimensions A Saw Height 47-1/4" B Min Length Pointer Up, Handle In 55-1/2" C Max Length Pointer Down, Handle Out 112" D Handle Extension 24" E Frame Width 23-3/8" F Frame Length 39-1/2" G Saw Width 29-7/8" H Front Axle Center Length 18-1/2" I Rear Axle Center Length 20-3/4" J Wheel Base Length 18-1/4" K Blade Shaft Max Height 16-1/2" Crated Saw Dimensions: 52" long x 34" wide x 54-1/2" high Pg. 19

18 Forward-positioned motor for more weight at the blade (and less on the operator) CC3700 SERIES CONCRETE SAW GAS and DIESEL MODELS The Most Compact 65 HP Saw on the Market - Fits Through a 30" Door! One hand sawing control Features powerful 65 HP Wisconsin gasoline engine (also available with 30 HP Deutz Diesel engine) Choice of 14" through 36" blade guards Has a frame designed for the higher torque of a large horsepower engine but more compact than the CC6500 Core Cut large saws have the best bearings, blade flanges and blade shafts in the business. Choice of Sundstrand or Eaton Transmission Maximum cutting depth 14-3/4" with 36" guard Pg. 20

19 CC3700 GAS and DIESEL SAW SPECIFICATIONS CC3700 Control Panel Cutting Depth Chart Blade Diameter 14" 20" 26" 30" 36" Cutting Depth 4-5/8" 7-5/8" 10-5/8" 11-3/4" 14-3/4" CC3700 Specifications Maximum Depth of Cut: 14-3/4" Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 6 or 8 Belt Blade Mounting: Right or left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on through 30", Bolt-on 36" Front Wheel Dimensions: 8" x 3" x 1" Rear Wheel Dimensions: 10" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Sundstrand-Sauer or Eaton Model 10 Drive Speed: feet per minute Air Filter: 4 stage Fuel Capacity: 6 gallons Electric Start: Standard High Temperature Shut-Off: Standard Hour Meter: Standard Tachometer: Optional Amp Meter: Standard Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Frame Lift: Standard Quick Release Rear Wheels: Standard Telescoping Front Pointer: Standard CC3700 Saws - Gas and Diesel Powered Models Model Engine Part No. Cat. No Part No. Cat. No. Blade Uncrated No. Type Sundstrand Sundstrand Eaton Eaton Capacity Wt. * CC HP Wisconsin " 1,320 lbs. CC HP Wisconsin " 1,330 CC HP Wisconsin " 1,340 CC HP Wisconsin " 1,350 CC HP Wisconsin " 1,360 CC HP Deutz Diesel " 1,320 CC HP Deutz Diesel " 1,330 CC HP Deutz Diesel " 1,340 CC HP Deutz Diesel " 1,350 CC HP Deutz Diesel " 1,360 Quick-release bladeshaft/flange, slip-on blade guards, quick-release rear wheels, double concave roller bearings are standard on CC3700 models. * Add 80 pounds for crated weight. CC3700 Options Description P/N Cat. No. Free Wheeling Clutch* Water Safety Switch Water Pump (electric) Parking Brake Spot Light Magnetic Spot Light Vertical Muffler (65 HP) Shaft Tachometer Lowering Speed Metering Valve Oil Cooler for 65HP Wisconsin Engine Soft Start Controller Add On ** Extended Blade Shaft Kit for spacing blades 3/4" to 1-1/2" Extended Blade Shaft Kit for spacing blades 1-1/2" to 2-1/4" * Standard on all electric saws. ** Factory installed. Extra Slip-On Blade Guards P/N Cat. No. 14" Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity CC3700 Dimensions A Saw Height 49" B Min Length Pointer Up, Handle In 59" C Max Length Pointer Down, Handle Out 116" D Handle Extension 24" E Frame Width 25-3/4" F Frame Length 46" G Saw Width* 32-1/4" H Front Axle Center Length 19-7/8" I Rear Axle Center Length 22-5/8" J Wheel Base Length 21-3/8" K Blade Shaft Max Height 19-1/2" * Saw width is reduced by removing blade guard and outer flange to permit entry through a 30" opening. Crated Saw Dimensions: 60" long x 36" wide x 56" high Pg. 21

20 CC3700 SERIES ELECTRIC SAW The Powerful, Multi-Application Electric Saw Largest dual voltage electric saw on the market Available with Optional Soft Start Electronic Overload Protection with External Reset Button Splashproof Control Box with Amp Meter Choice of Sundstrand or Eaton Transmissions Available with a 25, 30 or 40 HP electric motor Pg. 22 Core Cut large electric saws feature a large electric Controller/Starter and a large, 2" emergency stop button within easy reach of the operator. Available with Soft-Start option to reduce start-up power surge and allow the use of a smaller generator or other power source. 40 HP model is the most powerful electric saw on the smallest frame in the industry

21 CC3700 ELECTRIC SAW SPECIFICATIONS CC3700E Control Panel Cutting Depth Chart Blade Diameter 14" 20" 26" 30" 36" Cutting Depth 4-5/8" 7-5/8" 10-5/8" 11-3/4" 14-3/4" ** Specify 230V or 460V. 575V available on request. Includes motor starter switchbox. Quick-release bladeshaft/flange, slip-on blade guards, quick-release rear wheels, double concave roller bearings are standard on CC3700 models. 575V available on request. CC3700 Specifications Maximum Depth of Cut: 14-3/4" Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 6 or 8 Belt Blade Mounting: Right or left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on though 30", Bolt-on 36" Front Wheel Dimensions: 8" x 3" x 1" Rear Wheel Dimensions: 10" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Sundstrand-Sauer or Eaton Model 10 Drive Speed: feet per minute Electric Starter Box: Standard Hour Meter: Standard Amp Meter: Standard Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Frame Lift: Standard Quick Release Rear Wheels: Standard Free Wheeling Clutch: Standard Telescoping Front Pointer: Standard CC3700 Saws - Electric Models Model Engine Part No. Cat. No. Part No. Cat. No. Blade Uncrated No. Type Sundstrand Sundstrand Eaton Eaton Capacity Wt. * CC3740E HP Lincoln Electric (460V) " 1355 lbs. CC3740E HP Lincoln Electric (460V) " 1365 CC3740E HP Lincoln Electric (460V) " 1375 CC3740E HP Lincoln Electric (460V) " 1385 CC3730E HP Lincoln Electric (460V) " 1270 CC3730E HP Lincoln Electric (460V) CC3730E HP Lincoln Electric (460V) " 1290 CC3730E HP Lincoln Electric (460V) " 1300 CC3730E HP Lincoln Electric (460V) " 1310 CC3725E HP Leeson Electric** " 1305 CC3725E HP Leeson Electric** " 1315 CC3725E HP Leeson Electric** " 1325 CC3725E HP Leeson Electric** " 1335 CC3725E HP Leeson Electric** " 1345 *add 80 pounds for crated weight. Extra Slip-On Blade Guards P/N Cat. No. 14" Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity CC3700 Options - Electric Saws Description P/N Cat. No. Water Pump (electric) Spot Light Magnetic Spot Light Lowering Speed Metering Valve Soft Start Controller Add On* Extended Blade Shaft Kit for spacing blades 3/4" to 1-1/2" Extended Blade Shaft Kit for spacing blades 1-1/2" to 2-1/4" * Factory installed CC3700 Dimensions A Saw Height 49" B Min Length Pointer Up, Handle In 59" C Max Length Pointer Down, Handle Out 116" D Handle Extension 24" E Frame Width 25-3/4" F Frame Length 46" G Saw Width* 32-1/4" H Front Axle Center Length 19-7/8" I Rear Axle Center Length 22-5/8" J Wheel Base Length 21-3/8" K Blade Shaft Max Height 16-1/2" * Saw width is reduced by removing blade guard and outer flange to permit entry through a 30" opening. Crated Saw Dimensions: 60" long x 36" wide x 56" high Pg. 23

22 CC4000D SERIES CONCRETE SAW with Differential Drive and Optional Multi-Speed Blade System Adjust blade speeds quickly and easily Revolutionary easy access blade drive system allows you to quickly adjust blade speeds Choice of 35 HP Wisconsin gas engines or 30 HP Lincoln electric motors Maximum cutting depth 12-3/8" with a 30" guard Choice of 14", 20", 26" and 30" blade guards Available with single or multi-speed blade drive Fits through a 30" door Differential drive system allows for easy maneuverability. No heavy lifting to turn saw. Pg. 24 Easy accessible pulleys located in the front of the saw for quick saw speed adjustment CC4000D Advantages Easy to turn and maneuver thanks to the differential drive system. No heavy lifting to turn saw. Hydrostatic transmission with differential is totally enclosed. No exposed chains or gears. Differential lock provides positive drive to both rear wheels for maximum traction. All CC4000D saws come standard with quick-release bladeshaft/flange, slip-on blade guards, quick-release 10" rear wheels, double concave roller bearings, telescoping front pointer and 3 position handle bars. Bladeshaft tachometer standard. Free wheel neutral on hydrostatic transmission for manual maneuvering. 4 stage air cleaner with maintenance indicator for maximum engine protection.

23 CC4000D SPECIFICATIONS CC4000D Saws Engine Part Cat. Blade Blade Uncrated Model Type No. No. Cap. Speeds Wt.* CC4035DM HP Wisconsin (multi-speed drive) " 14" thru 30" 1,090 CC4035DM HP Wisconsin (multi-speed drive) " 14" thru 30" 1,100 CC4035DM HP Wisconsin (multi-speed drive) " 14" thru 30" 1,110 CC4035DM HP Wisconsin (multi-speed drive) " 14" thru 30" 1,120 CC4035D HP Wisconsin (single speed drive) " 14" 1,090 CC4035D HP Wisconsin (single speed drive) " 20" 1,100 CC4035D HP Wisconsin (single speed drive) " 26" 1,110 CC4035D HP Wisconsin (single speed drive) " 30" 1,120 CC4030EDM HP Lincoln Electric 460V (dual speed drive) " 14" and 26" 1,090 CC4030EDM HP Lincoln Electric 460V (dual speed drive) " 20" and 30" 1,100 CC4030EDM HP Lincoln Electric 460V (dual speed drive) " 14" and 26" 1,110 CC4030EDM HP Lincoln Electric 460V (dual speed drive) " 20" and 30" 1,120 All CC4000D saws come standard with quick-release bladeshaft/flange, slip-on blade guards, * Add 70 pounds for crated weight shaft tachometer, quick-release rear wheels and double concave roller bearings. 575V available upon request. CC4000D Control Panel Cutting Depth Chart Blade Diameter 14" 20" 26" 30" Cutting Depth 4-3/8" 7-3/8" 10-3/8" 12-3/8" CC4000D Specifications Maximum Depth of Cut: 12-3/8" Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 6 belt for model CC4000D Blade Shaft Drive: 8 belt for model CC4000DM Blade Mounting: Right or left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on Front Wheel Dimensions: 6" x 2" x 1" Rear Wheel Dimensions: 10" x 3" x 1" Handle Bars: 3 Position Transmission: Eaton Model 7 Drive Speed: feet per minute Air Filter: 4 stage Fuel Capacity: 6 gallons Electric Start: Standard High Temperature Shut-Off: Standard Hour Meter: Standard Tachometer: Standard Amp Meter or Volt Meter: Standard Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Frame Lift: Standard Quick Release Rear Wheels: Standard Telescoping Front Pointer: Standard CC4000D Options Description P/N Cat. No. Water Safety Switch Water Pump (electric) Spot Light Magnetic Spot Light Vertical Muffler Lowering Speed Metering Valve Soft Start Controller Add On* Extended Blade Shaft Kit for spacing blades 3/4" to 1-1/2" Extended Blade Shaft Kit for spacing blades 1-1/2" to 2-1/4" Extra Slip-On Blade Guards: 14" Capacity " Capacity " Capacity " Capacity * Factory installed CC4000D Dimensions A Saw Height 44-1/2" B Min Length Pointer Up, Handle In 47" C Max Length Pointer Down, Handle Out 100" D Handle Extension 20" E Frame Width 24" F Frame Length 36-1/2" G Saw Width* 31" H Front Axle Center Length 19" I Rear Axle Center Length 21" J Wheel Base Length 17" Blade Shaft Max Height 16-1/2" * Saw width is reduced by removing blade guard. Crated Saw Dimensions: 52" L x 34" W x 51" H Pg. 25

24 CC6500 SERIES CONCRETE SAW 65 HP Production Concrete Saw The most options and choices for the contractor in the industry (build it your way) Forward positioned motor One hand sawing control Fits through a 36" door Strongest frame in the industry Choice of 14" through 48" blade guards Core Cut frames are the best in the business, which improves your blade cutting speed and life. Shown with optional Spot Light Kit and Wisconsin Oil Cooler Kit Maximum cutting depth 14-3/4" with 36" guard (19-3/4" with optional 48" conversion kit) Pg. 26

25 CC6500 Control Panel Cutting Depth Chart Blade Diameter 14" 20" 26" 30" 36" 42" 48" Cutting Depth 4-5/8" 7-5/8" 10-5/8" 11-3/4" 14-3/4" 16-3/4" 19-3/4" * Free wheeling clutch standard on all electric saws. 575V available on request. Includes motor starter switchbox. Add 100 lbs. for crated wt. + For use with Sundstrand-Sauer transmission only. Standard on all electric saw models. For electric saws-factory installed. CC6500 SPECIFICATIONS CC6500 Specifications Maximum Depth of Cut: 14-3/4" (19-3/4" with optional 48" conversion kit) Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 8 or 10 belt Blade Mounting: Right or left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on through 30", Bolt-on 36" and up Front Wheel Dimensions: 8" x 3" x 1" Rear Wheel Dimensions: 10" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Sundstrand-Sauer or Eaton Model 10 Drive Speed: feet per minute Air Filter: 4 stage Fuel Capacity: 9 gallons Electric Start: Standard High Temperature Shut-Off: Standard Low Oil Alert: Pressure gauge Hour Meter: Standard Tachometer: Optional Amp Meter: Standard Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard CC6500 Saws Model No. Engine Type Sundstrand Sundstrand Eaton Eaton Blade Uncrated P/N Cat. No. P/N Cat. No. Capacity Wt. CC HP Wisconsin " 1420 lbs. CC HP Wisconsin " 1430 CC HP Wisconsin " 1440 CC HP Wisconsin " 1455 CC HP Wisconsin " 1465 CC6540E HP Lincoln Electric (460V)* " 1415 CC6540E HP Lincoln Electric (460V)* " 1425 CC6540E HP Lincoln Electric (460V)* " 1440 CC6540E HP Lincoln Electric (460V)* " 1450 CC6500 Options Description P/N Cat. No. 42" Blade Capacity Conversion Kit for Gas Saw " Blade Capacity Conversion Kit for Gas Saw " Blade Capacity Conversion Kit for Electric Saw " Blade Capacity Conversion Kit for Electric Saw Free Wheeling Clutch Water Safety Switch Water Pump (electric) Spot Light Magnetic Spot Light Vertical Muffler Oil Cooler for 65 HP Wisconsin engine Shaft Tachometer Lowering Speed Metering Valve Soft Start Controller Add On Parking Brake Extended Blade Shaft Kit for spacing blades 3/4" to 1-1/2" Extended Blade Shaft Kit for spacing blades 1-1/2" to 2-1/4" Extra Blade Guards: 14" Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity " Capacity " Capacity All CC6500 saws come standard with quick-release bladeshaft/ flange, slip-on blade guards, bladehaft tachometer, quick-release rear wheels and double concave roller bearings. CC6500 Dimensions A Saw Height 52-5/8" B Min Length Pointer Up, Handle In 62-1/2" C Max Length Pointer Down, Handle Out 124" D Handle Extension 24" E Frame Width 27-5/8" F Frame Length 49-1/2" G Saw Width 36" H Front Axle Center Length 21-3/4" I Rear Axle Center Length 24-1/2" J Wheel Base Length 23-7/8" K Blade Shaft Max Height 19-1/2" Crated Saw Dimensions: 65" long x 40" wide x 60" high Pg. 27

26 CC6560XLS 61 HP TURBO DIESEL SAW Many innovations and improvements make this fuel efficient, fast cutting and reliable 61 HP saw even better 61 HP turbo charged diesel engine (Uses half the fuel of a gas saw) Less rear end weight for easy maneuverability and reduced operator fatigue Choice of 14" through 36" blade guards Strongest frame on the market Fits through a 36" door Pg. 28 Maximum cutting depth 14-3/4" with 36" guard Quieter horizontal muffler with durable attachment Enclosed and hardened gears/chains for longer service life of transmission Reinforced and stiffened base frame for reduced warping Zero side load PTO (no side load or thrust load on the engine) Greater cutting depth for 26" blade guard model New 14" set-up with 2800 rpm blade speed Choice of 3.6" or 4.0" engine sheaves for either low speed or longer belt life Conventional 10 v-belt direct drive system CC6560XLS Saw Improvements - A Great Saw Just Got Better! Easy to replace banded belts Improved depth indicator and depth stop Hardened gears on wheel drive Reliable rotary tensioner for transmission belt Enclosed end drive that protects gear and chain Quick oil drain valve Hardened skid plates Reinforced upright, pump attachment and battery support

27 CC6560XLS SPECIFICATIONS CC6560XLS Control Panel Cutting Depth Chart Blade Diameter 14" 20" 26" 30" 36" Cutting Depth 4-5/8" 7-5/8" 10-5/8" 11-3/4" 14-3/4" CC6560XLS Saws CC6560XLS Specifications Maximum Depth of Cut: 14-3/4" Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 10 belt Blade Mounting: Right or left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on through 30", Bolt-on 36" Front Wheel Dimensions: 8" x 3" x 1" Rear Wheel Dimensions: 10" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Sundstrand-Sauer or Eaton Model 10 Drive Speed: feet per minute Air Filter: 4 stage Fuel Capacity: 9 gallons Electric Start: Standard High Temperature Shut-Off: Gauge and Warning Light Low Oil Alert: Warning Light Hour Meter: Standard Tachometer: Standard Amp Meter: Warning Light Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Frame Lift: Standard Quick Release Rear Wheels: Standard Model Engine Eaton Eaton Sundstrand Sundstrand Blade Uncrated No. Type Part No. Cat. No. Part No. Cat. No. Capacity Wt. * CC6560XLS HP Deutz Turbo Diesel " 1,420 lbs. CC6560XLS HP Deutz Turbo Diesel " 1,430 CC6560XLS HP Deutz Turbo Diesel " 1,440 CC6560XLS HP Deutz Turbo Diesel " 1,455 CC6560XLS HP Deutz Turbo Diesel " 1,455 All CC6560XLS saws come standard with quick-release bladeshaft/flange, slip-on blade guards, bladeshaft tachometer, quick-release rear wheels and double concave roller bearings. * Add 100 pounds for crated weight. CC6560XLS Options DESCRIPTION P/N Cat. No. Free Wheeling Clutch * Water Safety Switch Water Pump (electric) Spot Light Lowering Speed Metering Valve Parking Brake Glow Plug Blade Stacking Kit ** (up to 1-1/2" width) Blade Spacing Kit ** (up to 2" width) Blade Spacing Kit ** (up to 4" width) Side Plunge Kit ** (up to 6" width) 1-3/4" arbor Extra Blade Guards: 14" Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity (bolt-on) * For use with Sundstrand-Sauer transmission only. ** For 20" maximum blade capacity. CC6560XLS Dimensions A Saw Height 63" B Min Length Pointer Up, Handle In 60" C Max Length Pointer Down, Handle Out 124" D Handle Extension 24" E Frame Width (rear) 27-5/8" F Frame Width (front) 31-1/4" G Frame Length 49-1/2" H Saw Width * 37-1/8" I Front Axle Center Length 21-3/4" J Rear Axle Center Length 24-1/2" K Wheel Base Length 23-7/8" L Blade Shaft Max Height 19-1/2" * Saw width is reduced by removing blade guard to permit entry through a 36" opening. Crated Saw Dimensions: 64" long x 44" wide x 69" high Pg. 29

28 CC7100 SERIES CONCRETE SAW Turbo Charged Diesel Production Concrete Saw Longer life, lower maintenance engine than 65 HP gasoline engine Features Deutz 78 HP turbo charged diesel engine Forward-positioned motor for more weight at blade and less on the operator Better fuel economy and much higher sawing rates than a normal 65 HP gasoline engine Choice of 14" through 42" blade guards Excellent for bridge deck and parapet sawing Comes standard with shaft tachometer Extra heavy-duty reinforced single piece frame, designed specifically for the Deutz engine 16-3/4" maximum cutting depth with a 42" guard Pg. 30

29 CC7100 SPECIFICATIONS CC7100 Control Panel Cutting Depth Chart Blade Diameter 14" 20" 26" 30" 36" 42" Cutting Depth 4-5/8" 7-5/8" 10-5/8" 11-3/4" 14-3/4" 16-3/4" CC7100 Specifications Maximum Depth of Cut: 16-3/4" Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 10 Belt Blade Mounting: Right or left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on through 30" guard, bolt on 36" and 42" Front Wheel Dimensions: 8" x 3" x 1" Rear Wheel Dimensions: 10" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Eaton Model 10 Drive Speed: feet per minute Air Filter: 4 stage Fuel Capacity: 9 gallons Electric Start: Standard High Temperature Shut-Off: Gauge and warning light alerts operator Low Oil Alert: Warning light alerts operator Hour Meter: Standard Tachometer: Standard Amp Meter: Warning light alerts operator Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Frame Lift: Standard Quick Release Rear Wheels: Standard Telescoping Front Pointer: Standard CC7100 Saws Model No. Engine Type Part No. Cat. No. Blade Capacity Uncrated Wt.* CC HP Deutz Diesel " 1790 lbs. CC HP Deutz Diesel " 1800 CC HP Deutz Diesel " 1810 CC HP Deutz Diesel " 1820 CC HP Deutz Diesel " 1830 CC HP Deutz Diesel " 1850 * add 125 pounds for crated weight. CC7100 Options Description P/N Cat. No. Water Safety Switch Water Pump (electric) Spot Light Magnetic Spot Light Lowering Speed Metering Valve Extended Blade Shaft Kit for spacing blades 3/4" to 1-1/2" Extended Blade Shaft Kit for spacing blades 1-1/2" to 2-1/4" Parking Brake Extra Blade Guards: 14" Capacity (slip on) " Capacity (slip on) " Capacity (slip on) " Capacity (slip on) " Capacity " Capacity CC7100 Dimensions A Saw Height 63" B Min Length Pointer Up, Handle In 61" C Max Length Pointer Down, Handle Out 126" D Handle Extension 24" E Frame Width (Rear) 27-5/8" F Frame Width (Front) 37" G Frame Length 51" H Saw Width 43-1/4" I Front Axle Center Length 31" J Rear Axle Center Length 24-1/2" K Wheel Base Length 23-7/8" L Blade Shaft Max Height 22-1/2" Crated Saw Dimensions: 64" long x 44" wide x 70" high Pg. 31

30 CC7200 SERIES CONCRETE SAW Turbo Charged Diesel Deep-Cut Saw Features Deutz 78 HP turbo charged diesel engine Also available with 65HP gasoline engine 22-3/4" cutting depth with 54" guard Jackshaft design for high torque, lower RPM requirements for deep sawing with large diameter blades Forward-positioned motor for more weight at blade and less on the operator Choice of 26" through 54" blade guards Comes standard with shaft tachometer Optional 50 HP Baldor is the most powerful electric saw in the industry Extra heavy-duty reinforced single piece frame designed for deep sawing Pg. 32

31 CC7200 SPECIFICATIONS CC7200 Control Panel Cutting Depth Chart Blade Diameter 26" 30" 36" 42" 48" 54" Cutting Depth 9-3/4" 11-3/4" 14-3/4" 16-3/4" 19-3/4" 22-3/4" CC7200 Specifications Maximum Depth of Cut: 22-3/4" Blade Shaft Diameter: 1-3/4" Arbor Diameter: 1" with Single Drive Pin Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: 16 Belt Jackshaft, 10 Belt Engine Blade Mounting: Right or Left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on through 30" guard, Bolt-on 36" and up Front Wheel Dimensions: 8" x 3" x 1" Rear Wheel Dimensions: 10" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Eaton Model 10 Drive Speed: feet per minute Air Filter: 4 stage Fuel Capacity: 9 gallons Electric Start: Standard High Temperature Shut-Off: Gauge and warning light alerts operator Low Oil Alert: Warning light alerts operator Hour Meter: Standard Tachometer: Standard Amp Meter: Warning light alerts operator Cutting Depth Indicator: Standard Quick Disconnect Blade Flanges: Standard Quick Release Rear Wheels: Standard CC7200 Saws Model No. Engine Type P/N Cat. No. Blade Capacity Uncrated Wt.* CC HP Deutz Diesel " 2100 lbs. CC HP Deutz Diesel " 2110 CC HP Deutz Diesel " 2120 CC HP Deutz Diesel " 2140 CC HP Deutz Diesel " 2160 CC HP Deutz Diesel " 2175 CC HP Wisconsin " 1735 CC HP Wisconsin " 1745 CC HP Wisconsin " 1755 CC HP Wisconsin " 1775 CC HP Wisconsin " 1795 CC HP Wisconsin " 1810 CC7250E HP Baldor Electric (460V) " 1735 CC7250E HP Baldor Electric (460V) " 1745 CC7250E HP Baldor Electric (460V) " 1755 CC7250E HP Baldor Electric (460V) " 1775 CC7250E HP Baldor Electric (460V) " 1795 CC7250E HP Baldor Electric (460V) " 1810 * add 150 pounds for crated weight. CC7200 Options Description Part No. Cat. No. Water Safety Switch (diesel saw) Water Safety Switch (gas and electric saw) Water Pump (electric) Spot Light Magnetic Spot Light Vertical Muffler ** Oil Cooler for 65HP Wisconsin Lowering Speed Metering Valve Soft Start Controller Add-On Parking Brake Extra Blade Guards: 26" Capacity (slip on) " Capacity (slip on) " Capacity " Capacity " Capacity " Capacity ** Standard on CC7272, Optional for CC7265 For electric saws only - factory installed. CC7200 Dimensions A Saw Height 63" B Min Length Pointer Up, Handle In 70" C Max Length Pointer Down, Handle Out 135" D Handle Extension 24" E Frame Width (Rear) 27-5/8" F Frame Width (Front) 37" G Frame Length 60" H Saw Width 43-1/4" I Front Axle Center Length 31" J Rear Axle Center Length 24-1/2" K Wheel Base Length 25-3/8" L Blade Shaft Max Height 28-1/2" Crated Saw Dimensions: 80" long x 44" wide x 70" high Pg. 33

32 CC7878 EZ RIDER JOINT CUTTING SAW Fast Maneuverability and Easy Operation Makes The EZ Rider The Best Saw In the Joint! Fast Maneuvering and Easy Operation Features for High Productivity Many easy operation and strong handling features for less operator errors More reliable and easy to use thanks to precise belt tensioning and stronger shaft and bearings Many Ergonomical Features for Less Operator Fatigue 20-inch maximum blade capacity Pg. 34 CC7878 EZ Rider Joint Cutting Saw Features and Advantages Fast driving speed with precise and stable steering Perfect blade visibility Two independent water adjustments for joint cleaning Extra wide 5" wheels that are adjustable Adjustable seat and steering Vibration isolated seat and foot rest 3 Lights Adjustable lowering speed Folding pointer for storage on the saw Patented linear belt tensioner for precise alignment of 2" blade shaft Large double row tapered roller bearing on the blade shaft Enclosed belt drive for longer belt and pulley life Automatic engine overheat and low oil shut off Remote grease zerks for easy greasing Easy belt removal thanks to inboard bearing support Zero maintenance front wheels

33 CC7878 EZ RIDER SAW SPECIFICATIONS CC7878 EZ Control Panel Cutting Depth Chart Blade Diameter 14" 20" Cutting Depth 4" 7" CC7878 EZ Rider Saw Options Description Part No. Cat.No. Extra Blade Guards: 14" Capacity * " Capacity * Saw comes standard with 14" blade guard CC7878 EZ Rider Dimensions Saw Height 72" Frame Length 80" Saw Width 57" Frame Width 26-1/2" Front Axle Center Length 39-7/8" Wheel Base Length 48" CC7878 EZ Rider Saw Specifications CC7878 EZ Rider Saw with 14" Blade Guard Part No Catalog No Motor: Deutz 78 HP turbo cxharged diesel, air cooled with electronic shutdown Air Filtration: Duel element with rotating vane pre-cleaner Fuel Tank Capacity: 20 gallons with sending unit for gauge Hydraulic system: Hydrostatic wheel drive with seat actuated shutdown Steering Hydraulically controlled rotary actuator Hydraulic Tank Capacity: 10 gallon tank with suction and return filters Max. Blade Capacity: 20" Max. Cutting Depth: 7" with a 20" blade Blade Shaft Diameter; 2" Blade Shaft Bearings: Roller bearing pillow blocks Blade Drive Belts: (10) 3V Belts (2 sets of 5) Blade Raise/Lower Mechanism: Electric over hydraulic system - 12 VDC Frame: 2" x 4" x.188 wall tubing Wheels (2 front, 1 rear): 14" diameter wheels x 5 wide tires Wheel Bearings, Front: Sealed front bearings to eliminate greasing Travel Speed - Forward/Reverse: feet per minute by hydraulically driven rear wheel Depth Stop: Dual Side Tachometer; Standard Fuel Gauge: Standard Hour Meter: Standard Water Safety Switch: Standard Lifting Bale: Standard Weight: 1,950 lbs. CC9085 Centerline Saw Designed to cut perfectly straight centerline joints, the new CC HP Turbo Diesel reduces blade wear and saves you on labor costs 85 HP turbocharged 4-cylinder diesel engine 16" blade capacity Weather-proof enclosure 40 gallon fuel tank 5" maximum cutting depth Smooth and quiet operation Fine speed control with adjustable flow control Runs two blades in line at the same time Pivoting platform permits individual depth setting for each blade Rear axle assembly has a pivoting adjustment for sawing on banked curves CC9085 CC9085 Centerline Saw Specifications Part No Catalog No ENGINE 85 HP Isuzu turbocharged liquid cooled diesel Fuel Capacity: 40 gallons BLADE DRIVE Blade Capacity: 16" Maximum Depth of Cut: 5" Variable Speed rpm upcutting or downcutting Dual Valve Water Conrol (one for each blade) Quick Change Blade Guard with 4 water coolant distribution tubes. PROPULSION Travel speed and direction controlled by console mounted toggle switch and rotary travel speed dial. Drive Speed: feet per minute HYDRAULICS Twin 30 GPM hydrostatic pumps drive two separate piston blade motors 30 gallon hydraulic resovoir with sight gauge RAISE/LOWER 12 volt DC power unit connects to hydraulic cylinders to raise and lower the cutting head Pg. 35

34 CC8000 RIDER CONCRETE SAW Patented Design That Delivers Maximum Flexibility Hydraulic-driven blade shaft delivers an infinitely variable RPM with no horsepower loss for 14" to 54" blade diameters Arm-mounted blade raises and lowers easily (while engine and operator remain level) Excellent multi application platform 78 HP Deutz Diesel standard with isolators to reduce vibration 22-3/4" maximum cutting depth with 54" guard Zero Turn Radius with New Power Steering Arm can be rotated to enter cut at up to a 10-degree angle Less operator fatigue with low maintenance and easy serviceability Accommodates 14" through 54" Blade No belts to tighten or replace Converts from a downcut to an upcut saw in less than a minute (great for joint widening or rehab) Pg. 36

35 CC8000 RIDER SAW SPECIFICATIONS CC8000 Rider Saw Control Panel Hydraulic Steering for Precise Turning CC8000 Specifications Maximum Depth of Cut: 22-3/4" Blade Guard Capacity: 54" Blade Shaft Diameter: 2-1/2" Arbor Diameter: 1" with single drive pin Blade Shaft Bearings: Precision ball Blade Shaft Drive: Hydraulic motor Blade Mounting: Right Blade Raise and Lower: Hydraulic pump, solenoid valve controlled Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Slip-on through 30", Bolt-on 36" and up Front Wheel Dimensions: 10" x 4" x 1-1/4" Rear Wheel Dimensions: 12" x 6-1/2" x 1" Transmission: Variable displacement hydraulic pump and motor Drive System: Direct/hydraulic Air Filter: 4 stage Fuel Capacity: 9 gallons Electric Start: Standard High Temperature Shut-Off: Gauge/Light Low Oil Alert: Warning Light Hour Meter: Standard Tachometer: Standard Amp Meter: Warning light Adjustable Depth Stop: Standard Blade Shaft Wrench: Standard Quick Disconnect Blade Flanges: Standard Hydraulic Oil Capacity: 17 gallons Telescoping Front Pointer: Standard Cutting Depth Chart Blade Diameter 14" 20" 26" 30" 36" 42" 48" 54" Cutting Depth 3-3/4" 6-3/4" 9-3/4" 11-3/4" 14-3/4" 16-3/4" 19-3/4" 22-3/4" CC8000 Saws Model No. Engine Type P/N Cat. No. Blade Capacity Uncrated Wt.* CC HP Deutz Diesel " 2,620 lbs. CC HP Deutz Diesel " 2,630 CC HP Deutz Diesel " 2,640 CC HP Deutz Diesel " 2,650 CC HP Deutz Diesel " 2,670 CC HP Deutz Diesel " 2,680 CC HP Deutz Diesel " 2,690 CC HP Deutz Diesel " 2,700 CC8072-C30 Curb Cutting Rider Saw " 2,900 * Add 250 pounds for crated weight CC8000 Rider Saw Options Description Part No. Cat. No. Water Pump Kit Catalytic Converter Muffler Dust Collection System Extra Blade Guards: 14" Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity (slip-on) " Capacity " Capacity " Capacity " Capacity CC8000 Dimensions A Saw Height 67-3/4" B Min Length Pointer Up 82" C Max Length Pointer Down 129-1/4" D Frame Width 45" E Frame Length 58" F Saw Width 64-5/8" G Front Axle Center Length 39-7/8" Wheel Base Length 47-1/2" Blade Shaft Max Height 31-5/8" Pg. 37

36 CC8000 CURB CUTTING RIDER SAWS CC8000 Curb Cutting Rider Saw Hydraulically powered curb cutting system attaches onto any existing or new Core Cut CC8000 Rider Saw. 78 HP Deutz diesel motor. Dual hydraulic controls within easy reach of operator. Pitch angle varies over 135 degrees. Blade can be adjusted to a variety of angles. 36" blade capacity with hydraulic controlled raise/lower and plunge/retract operation. Can be converted to a conventional rider saw. Water tank and digital level included. Curb Cutter 2000 High Production Saw Precision ride-on, single operator machine that can cut a 16 foot driveway opening in one hour. Choice of 80 HP or 100 HP John Deere engine. Cuts driveway and ramp openings in all types of existing curbs. Flush cuts parapet and barrier walls, garage door openings and can perform articulated cutting. Precise diamond cutting means there s no damage to adjacent curb structure or roadway. Robust but compact design means the Curb Cutter 2000 easily fits on an existing flatbed trailer - unlike other curb cutters which require a dedicated truck. ❶ Flush Cut Once the location of the new driveway/sidewalk is determined, the Curb Cutter 2000 cuts a flush cut along the bottom of the monolithically poured curb. Driveway/sidewalk With the CC8000 Curb Cutting Rider Saw the blade can be adjusted to various angles ❷ Angle Cut After the flush cut is completed, angle cuts are made. ❸ Corners ground Roadway Sidewalk Ramp Once the cuts are finished, the debris is broken away and removed leaving a completed driveway/sidewalk opening with no damage to remaining curb structure or pavement. Pg. 38

37 CURB CUTTING RIDER SAW SPECIFICATIONS CC8000 Curb Cutting Rider Saw CC8000 Curb Cutting System CC8072-C30 Curb Cutting Rider Saw Part No complete with curb cutter attachment Cat. No Curb Cutter Attachment Part No without hydraulic motor - keyed shaft Cat. No Curb Cutter Attachment Part No without hydraulic motor - spline shaft Cat. No Curb Cutter Attachment Part No with hydraulic motor - keyed shaft Cat. No Curb Cutter Attachment Part No with hydraulic motor - spline shaft Cat. No Curb Cutter Conversion Kit for Part No Rider Saw with spline shaft Cat. No Curb Cutter Conversion Kit for Part No Rider Saw with keyed shaft Cat. No Curb Cutter Mounting Service Part No (mounting attachment to rider saw) Cat. No Saw Ht. with Curb Cutter System 72" Overall Saw Frame Width 65" Overall Saw Frame Length 113" Front Axle Center Length 39-7/8" Wheel Base Length 47-1/2" Blade Shaft Max Height 31-5/8" CC8000 Curb Cutter Width 28-1/4" CC8000 Curb Cutter System Length 26" Maximum Blade Diameter 30" Maximum Plunge 12" Curb Cutter 2000 Curb Cutter 2000 Saws Model No. Engine Type Part No. Cat. No. Blade Cap. Wt. Curb Cutter HP John Deere CS " Flush Cut 5,800 lbs Curb Cutter HP John Deere CS " Flush Cut 5,800 Curb Cutter 2000 Options Description Part No. Catalog No. Hydraulic Grinder CS-2000-HG Curb Saw Trailer CS-2000-T Curb Cutter 2000 Specifications ENGINE John Deere water cooled engine with electronic safety shut down system Fuel Tank Capacity: 28 Gallons Drive Speed: feet HYDRAULICS: 75 gallon hydraulic oil tank capacity Blade pump 60 GPM Pressure Flow Comp. Closed loop ground drive pump with piggy back gear pump for cylinder functions 5 bank control valve 10 micron hydraulic filters High efficiency hydraulic heat exchanger Hydraulic flow meter and pressure gauge BLADE Maximum Blade Diameter: 36" Flush Cut Maximum Plunge: 15" Maximum Vertical: 10" Maximum Right to Left Angle: 15 degrees Maximum Reverse Angle with 20" blade: 5 degrees Arbor Diameter: 1" Blade Tilt: degrees CONTROL PANEL: Tachometer, Engine Temperature, Hour Meter, Volt Meter, Starter Switch, Oil Pressure Gauge, Murphy Switches and Strobe Light Switch FEATURES: Mechanical Parking Brake, 6" Diameter Solid Rubber Wheels, Water Tank Standard and Safety Strobe Light OPTIONS Stanley Pole Grinder Working Lights DIMENSIONS Saw Length: 130" Saw Height: 87" Saw Width: 62" Pg. 39

38 120 HP SLAB SAW 120 HP of Cutting Power Packed in a Compact Frame Powerful V6 4.3L industrial engine Features a break-away sheave on the jackshaft. If the saw slams, it shifts the clutch to free-wheeling mode - saving damage to belts and polychain and reducing downtime. Maximum cutting depth of 15 4 pin collars, standard 1" arbor blade shaft Pg. 40 Blade shaft RPM 1850 Outboard bearing support Mechanical governor CC120-SS Control Panel CC-120-SS Slab Saw Specifications Part Number: CC-120-SS Catalog Number: Uncrated Wt. * 2,150 lbs. Blade Shaft Diameter: 2" Maximum Depth of Cut: 14-3/4" Arbor Diameter: 1" - with 4 drive pin collars Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: Five 5 V Belts Jackshaft Poly Chain to Blade Shaft Blade Mounting: Right or Left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachments: Bolt-on 24", 30" or 36" Front Wheel Dimensions: 10" x 3" x 1" Rear Wheel Dimensions: 12" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Sundstrand Drive Speed: feet per minute Air Filter: 2 stage Fuel Capacity: 9 gallons Electric Start: Standard Gauges: Tachometer, Oil Pressure, Water Temperature, Vacuum, Volts and Hour Meter Light Bar: Optional * Add 125 pounds for crated weight. Cutting Depth Chart Blade Diameter 24" 30" 36" Cutting Depth 7-5/8" 11-3/4" 14-3/4" CC-120 Dimensions Saw Height 53" Min Length Pointer Up, Handle In 62" Max Length Pointer Down, Handle Out 124" Handle Extension 24" Frame Width 30" Frame Length 50" Saw Width 36" Front Axle Center Length 21-3/4" Rear Axle Center Length 24-1/2" Wheel Base Length 23-7/8" Aluminum radiator with mechanical fan Standard 36" blade guard

39 CC120 DEEP CUT SLAB SAW The Very Powerful V-6 Saw That Cuts Up to 26 Inches Deep Powerful V6 4.3L GM industrial engine Large sheave torque acceleration Aluminum radiator with mechanical fan Standard 54" blade guards Maximum Cutting depth of 31-3/4" Outboard bearing support Mechanical governor Blade shaft RPM 833 Hydrostatic transmission/ chain drive CC120 Deep Cut Slab Saw Specifications Part Number: CC-DC-SS Catalog Number: Weight: 2,550 lbs. Blade Shaft Diameter: 2-1/2" CC-DC-SS Deep Cut Slab Saw Maximum Depth of Cut: 22-3/4" Arbor Diameter: 1" (no drive pin hole) Blade Shaft Bearings: Self-aligning double concave roller Blade Shaft Drive: Five 5 V Belts Jackshaft Poly Chain to Blade Shaft Blade Mounting: Right or Left Blade Raise and Lower: Electro-hydraulic pump Blade Coolant: Dual multi-spray tubes Blade Guard Attachment: Bolt-on Front Wheel Dimensions: 10" x 3" x 1" Rear Wheel Dimensions: 12" x 3" x 1-1/4" Handle Bars: Tilt Transmission: Sundstrand Drive Speed: feet per minute Air Filter: 2 stage Fuel Capacity: 9 gallons Electric Start: Standard Gauges: Tachometer, Oil Pressure, Water Temperature, Vacuum, Volts and Hour Meter * Add 125 pounds for crated weight. Optional Blade Guards, Accessories Blade Guard Size: Part No. Cat. No. 60" Capacity CC-60-BG-F " Capacity CC-66-BG-F Hydraulic Bogie Wheel Kit CC-DC-BK Cutting Depth Chart 6 bolt blade collars with safety hub Remote greasing of blade shaft and jack shaft bearings Blade Diameter 36" 42" 48" 54" 60" 66" Cutting Depth 11-3/4" 14-3/4" 16-3/4" 19-3/4" 22-3/4" 25-3/4 CC-120 Dimensions Saw Height 53" Min Length Pointer Up, Handle In 62" Max Length Pointer Down, Handle Out 144" Handle Extension 24" Frame Width 30" Frame Length 50" Saw Width 36" Front Axle Center Length 21-3/4" Rear Axle Center Length 24-1/2" Wheel Base Length 23-7/8" Pg. 41

40 COMPLETE PREWIRED ELECTRIC SAWS CORE CUT Small Electric Saws CC1000, CC1300, CC1800 and CC2500 Series Saws 2.5, 5, 7.5, 10 or 15 horsepower Single or three phase Splash proof, non-corrosive control box with amp meter Controls within safe reach of operator yet out of the way Bolt on control box cover for easy access Thermal overload protection for motor Amp meter to protect against motor overload Core Cut CC1300XL Electric Saw Electric Saws Core Cut electric saws are the best kept secret in the industry, featuring power options from 2.5 HP through 50 HP and state-of-the-art user friendly control boxes designed with specifications to match whatever motor you choose, making these electric saws the easiest to operate and service. All you need to do when you select a Core Cut electric saw is add your power cord and go! Why go with electric power over diesel or gasoline? Very quiet. High power output vs size. Can operate at any angle. Low vibration - smooth running. Longer blade life. No heat or exhaust generated at the operator. Lower energy costs vs fuel. Lower motor maintenance. Lower motor replacement cost. No governor drop. Only OSHA approved power source for confined areas. Can be used wet or dry with no additional maintenance. Motors can be repaired/rewound at about 1/4 the cost of a gas engine rebuild. Pg. 42 CORE CUT Large Electric Saws: CC3500, CC3700, CC4000D, CC6500 & CC7200 Series 20 HP, 25 HP, 30 HP, 40 HP, 50 HP 230 volt or 460 volt (575 volt available on request) Complete control/starter box - no switchgear to buy Splash proof control box with amp meter mounted on rubber isolators to minimize vibration of electrical components Controls within safe reach of operator yet out of the way Large 2" emergency stop button in easy reach of operator Hinged control box cover for easy access Control box has main on/off switch that prevents box from being opened with power on - reducing the chances of accidental operator contact with live internal components State-of-the-art electronic overload protection device for motor instead of thermal overload - won t be affected by external environmental temperatures - prevents nuisance circuit tripping Easy voltage changeover without the need to replace any control/starter components for 20 HP and 25 HP motors Battery charger is integral part of controller/starter - eliminates need for external belt-driven alternator that reduces power from motor and can easily be damaged by slurry or other contaminates Available with Soft-Start option - reduces start up power surge allowing the use of a smaller generator or other power source