Slurry tanker

Transcription

1 Slurry tanker

2 Gti 4500 Complete range from to litres Gti 6500 Gti Design and manufacture 100% Jeantil Spot welded girders Hot-dip galvanisation DESP tank calculation

3 Expertise and design 100% JEANTIL Strong innovative construction - Tank resting on 2 girders stud welded throughout its length - Continuous welded girders - Edge to edge welded ferrules - Optimised tank weight for transport of liquid only - Wheels flush fitted into the tank Quality of manufacture - Manufacture 100% JEANTIL - Continuous mechanically welded unit inside and outside - Conformity to the DESP 97/23 CE (1) - Automatic welding of ferrules - Continuous quality control Complete emptying of all products - Drop frame spot welded rear - Pneumatic interior mixer - Smooth tank floor with natural slope - Mountain emptying - Top rear outlet with sump Better filling - Large volume filling security - optimisation of suction Ø - Submerged pumping turbine with vent Multi-purpose use - Mountain emptying - Interior paint protection for transport of specific products - Tank exterior protection paint - Tank partitioned clean water for pressure washing Safety of use - Interior baffle partitions - Overpressure safety devices - 2nd filling security - Self-cleaning detritus chamber Simplified cleaning - Hot-dip galvanised tank - Rear door Ø900 or side Ø600 - Smooth tank floor for no retention - Baffle partition with through access (1) DESP : Pressurised Equipment Directive > 0,5b Double filling security Pneumatic interior mixer Rear door Ø900 Weight transfer partition Protection paint Range Gti 4500 to Mountain emptying on a downwards slope Range to Interior baffle partition Side door Ø600 Range to Volume to treat <5000 m3/year Volume to treat >5000 m3/year Distance from fosse to field >2.5 km Pumping by manual valve Pumping with reception cone Direct pumping into the fosse Spreading with nozzle on bare ground Spreading on crops Injection of slurry Possible ++ Favourable +++ Very favourable 3

4 Single axle Bogie Tandem Complete range of slurry tankers 1, 2 and 3 axles Tridem Hydraulic suspension Following axle Hydraulic suspension Steering axle Brakes range independent chassis i range integral chassis Performances and behavious Single axle Bogie suspension Tandem suspension Tridem suspension Hydraulic suspension Normal Reversed Normal Reversed Normal Reversed 2 3 axles Transport Spreading Clearance Handling (1) +++ (1) +++ (1) +++ (1) ++ (1) ++ (1) +++ (1) Maintenance and long life Possible ++ Favourable +++ Very favourable (1) With following or drive axles

5 Performance and maximum comfort in all conditions Better stability - Possible fitting of large Ø wheels - Drop frame bogie, tandem and tridem axle - Wheels flush fitted into the tank - Hydraulic suspension Respect for soils - 1, 2 or 3 axles - Low pressure tyre up to 800 mm wide - Optimised dead weight thanks to independent chassis - Remote inflation to adjust the tyre pressure at work and on the road Robust, reliable design - Tubular chassis - Chassis tank connection by brackets on - Oversized running gear - Drawbar pin 500 mm greased bushing - Drawbar main section in HLE steel - Ring welded or bolted on the draw bar - Bolted axles Handling - Following axle on bogie, tandem, tridem - Steering axle on bogie, tandem, tridem - 2 following axles on tridem - 2 steering axles on tridem Optimised need for power - Weight transfer partition on the front of the tanker - Drop frame axle - Weight transfer on hydraulic suspension - Possible fitting of large Ø wheels Comfort of use - Spring draw bar suspension - Adjustable drawbar height - Hydraulic or mechanical stand - Pneumatic braking proportional to the load Compliant for road use - Protected double lighting - side lights - DREAL France approval 25 km/h and 40 km/h Double lamp protected lighting Proportional braking 40 km/h Mechanical stand Hydraulic stand Welded ring Bolted ring Ø50 Bolted ring coupling ball Ø 80 Gti 4500 Gti 5500 Gti 6500 Gti 8500 Gti Integral chassis Single axle Flush fitting Fixed drawbar Spring drawbar Welded ring Bolted ring Ø50 Ring coupling ball K80 Authorisation 25km/h Independent chassis Single axle Bogie Tandem Tridem Hydraulic suspension Following axle Steering axle 2 following axles on tridem 2 steering axles on tridem Flush fitting Spring drawbar Welded ring Bolted ring Ø50 Ring coupling ball K80 Authorisation 25km/h Authorisation 40km/h standard option (1) Tandem or Tridem according to PTAC with pneumatic braking proportional to the load 5

6 Side valve Coupling system Complete range of loading solutions Central arm Underground pit Geo-membrane pit Upper loading hoist Virgule arm Turbo arm Outside pit Well Lagoon Pumping accelerator Filling cone Hydraulic top opening Manual valve Ø150 Manual valve Ø200 Central arm Ø150 Central arm Ø200 Virgule arm Ø200 Turbo arm Ø200 Gti range range Type of slurry Slurry < 5% Dry Matter Slurry 5 to 10% DM Slurry 10 to 15% DM (1) +++(1) +++(1) Type of pit Lagoon Geo-membrane pit Underground pit Outside pit Well Altitude > 600m (1) +++(1) +++(1) Pumping Pumping on reception cone solution Pumping direct pit Pumping accelerator Pumping turbine up to 6 m3 /min Pumping turbine up to 10 m3 /min Pumping without compressor Option + Possible ++ Favourable +++ Very favourable (1) With pumping accelerator and security 6

7 Performance and multiple use adapted to the needs of each user Optimised pumping time - Pumping rate up to 13 m3/mn - Large rate pumping accelerator - Pumping with or without low pressure - Pumping arm Ø Slurry mixing and grinding with the Turbo Mix Better filling rate - Large volume raised pumping security - 2nd security with large volume detritus chamber - Pumping without low pressure with slurry/foam return circuit towards the pit - Slurry preparation with the Turbo Mix Pumping turbine 10m3/min Pump accelerator 6m 3 /min Innovative loading solutions adapted to livestock farms - Filling cone Ø200 and vent Ø150 - Hydraulic top opening Ø600 - Pumping accelerator - Pumping arm Ø200 Filling without compressor Pump flow rate according to configuration Multi-purpose pumping systems - Pumping direct or on cone with Virgule and Turbo arm - Pumping by side valve Ø150 or Reception cone with remote control opening Comfort of use - Semi-automatic system for coupling the pumping hose - Sequential control of the central arm - Electrical control for Virgule and Turbo arm - Reception cone with remote control opening Reliability and very long life - Galvanisation of all parts in contact with the slurry Turbo mixer - Mixing and grinding by Ø700 screw thread cutters and 1 counter-cutter - 5.5m model for pit up to 2.5 m in depth - 7m model for pit up to 3.5 m in depth Compressor DL200 + Turbine 10 m 3 /min Compressor + accelerator + arm Ø 200mm Compressor + arm or valve Ø 200mm With hydraulic flow rate of 80 to 120 l/min at 200b for Turbine Pumping turbine 10 m 3 /min + arm Ø 200mm Pumping turbine 6 m 3 /min + arm Ø 200mm Compressor + arm or valve Ø 150mm Turbo Mix 5.50m Ø700 paddle propeller 7

8 Exact nozzle Complete range of spreading solutions Exact Té bi-nozzles RE 248 Nozzle Té bi-nozzles Spade ramp RB 303 RP Disc injector Nozzle ramp EDV EDS 48-8 Tine injector Hanging ramp EDD

9 Performance and multiple use adapted to the needs of each user Optimised work rate - Spreading up to 30 m in one run - Emptying rate uo to 9 m3/mn - Outlet Ø150 or Emptying accelerator on top outlet Ø150 Respect for environmental constraints - Automatic spreading control in m3/ ha - Large width slurry injection on bare earth and meadow - Slurry deposit in line using hanging ramp - Reduction of smells - Maximum use of slurry fertilising elements - Output curve for each device to adjust its dose Economies at all levels - Use of slurry instead of mineral fertiliser on cereals - Reduction of nitrogen losses with injector and ramps - Work rate > than 100 m3 spread per hour - Spreading and injection in just one run Quality of spreading - Ramp and injector with variation of transversal distribution <10% with grinder distributor - Automatic adjustment of dose spread with flowmeter - Output curve for each device to adjust its dose Multi-purpose use - Pre-equipment to receive spreading tools on - Work possible on all types of cropping patterns (see table) - Dose of 5 to 100 m3/ha possible according to tools - Working width from 2.5 to 30 m Comfort of use - Automatic dose adjustment device with flowmeter - Output curves for simple adjustment of the dose Very long life - Galvanisation of spreading tools Desired dose m 3 /h Exact nozzle output curve Desired dose m 3 /h Flow rate curve Nozzle Exact Ø 150mm Pressure 1b, valve opening 100%, fertiliser pig slurry Spade ramp output curve RE248 Nozzle Forward speed km/h Nozzle ramp Spade ramp Nozzle working width = 10 m Flow rate curves given as an indication : Do the calculation again for each change of parameter (see method on the user s manual) Flow rate curve RE m 8 spades Pressure 1b, valve opening 100%, fertiliser pig slurry Forward speed km/h Flow rate curves given as an indication : Do the calculation again for each change of parameter (see method on the user s manual) Hanging ramps Square tined injector Inductive flowmeter flush fitted in the tank Dosimat grinder-distributor Exacut grinder-distributor Vibro tine injector 1 row disc injector 2 row disc injector Gti range range Bare ground Prepared land Stubble Grassland Cereals TP soil stabilisation +++ Pig slurry (2) Straw slury (2) ++ (2) ++ (2) ++ (2) ++ (2) ++ (2) Thick slurry (rabbits) (2) Poultry slurry (2) +++ (2) +++(2) +++(2) +++(2) +++(2) Liquid mud bio-gas (2) digestat Reduction in ammonia (2) nitrogen losses Spreading regularity (1-2) +++ (2) +++(1-2) +++(1-2) +++(1-2) +++(1-2) Work rate (2) Sensitivity to the (2) wind Reduced smells + ++ (2) Possible ++ Favourable +++ Very favourable (1) With Dosimat grinder- distributor (2) With Exacut grinder - distributor Nozzle EZ Outlet Ø45 Nozzle EZ Outlet Ø60 Nozzle EZ Outlet Ø70 Nozzle EZ Outlet Ø80 RE 248 Standard Feed Ø150 RE 248 Dosimat rotor étoile Feed Ø150 RE 248 Feed Ø200 répartiteur standard RE 248 Feed Ø200 Exacut GD 9

10 Slurry tanker integral chassis 1 axle Gti 4500, 5500, 6500, 8500, Gti 8500 inset pumping arm Gti 6500 spreading Gti 8500 inset 10

11 The multi-purpose, economical and easy to handle slurry tanker Complete emptying of all products - Smooth tank floor for no retention - Spot-welded rear drop frame Ø150 or Pneumatic interior mixer Ø80 - Mountain emptying - SE hydraulic bronze rear valve - Industrial valve DE Ø150 or 200 for slurry with straw Multi-purpose use and performance - Low centre of gravity with integral chassis - Wheels flush fitted up to Ø Pre-equipment front outlet Ø150 - Manual valve pumping Ø150 or Central pumping arm Ø150 or Spreading with nozzle or té bi-nozzles - Drawbar ring welded or bolted - security and large volume detritus chamber Simplified cleaning - Entirely galvanised monobloc unit - Rear door Ø900 - Smooth tank floor for no retention Safety of use - Sealed pressure safety valve - Baffle partition according to model - Higher safety of ball valve filling - Front detritus chamber - security and large volume detritus chamber - Pressure and low pressure control manometer Quality of manufacture - Tube girders integral to the tank - Continuous mechanically welded unit inside and outside - Conformity to the DESP 97/23 CE - Automatic welding of ferrules - Continuous quality control Comfort of use - 1 or 2 level warning lights according to model - Column level warning light - Mechanical or hydraulic stand Compliant for road use - Double lamps protected lighting - Approved braking Rear door Ø900 and industrial valve Bronze valve as standard Fixed drawbar security Double safety filling as standard Level indicators Column level indicators Baffle Spring drawbar Compressor oil can Characteristics in basic version Gti 4500 Gti 5500 Gti 6500 Gti 8500 Gti Tank volume (lt) * PTAC (kg) ** Empty weight (kg) Tank Ø (mm) Baffle Level indicators Front valve piquage G G G G G Basic wheels 15x22,5 15x22,5 15x22,5 15x22,5 16x22,5 Standard version dimensions Tank length Overall length Overall width Overall height (*) Loss of volume with flush fitting (**) The actual on-road load corresponds to a basic material and reduces according to options 11

12 Slurry tankers Independent tank and chassis 1,2 or 3 Axles 10500, 11500, 12500, 14000, 15500, 18500, 20500, flush fitted

13 The benchmark for performance and multi-purpose use Complete emptying of all products - Drop frame rear outlet Ø150 or Top outlet with stone sorter - Pneumatic mixer Ø80 - Mountain emptying - SE hydraulic bronze rear valve - Industrial valve DE Ø150 or 200 for slurry with straw Better filling - Large capacity high security - Large volume front detritus chamber - Accelerator on pumping arm - Turbine on pumping arm with air vent Strong innovative construction - Independent galvanised tubular chassis - Tank bolted onto the chassis - Rear door Ø900 or side Ø600 - Chassis pre-equipment for lifting - Drawbar pin 500 mm greased bushing - Bolted ring as of Multi-purpose use - Flush fitted wheels up to Ø Direct pumping Ø150 or Central, virgule or turbo pumping arm - Spreading with nozzle or té bi-nozzles Comfort of use - Electrical controls and automatic management of spreading - Column level indicators - Hydraulic stand - Sequential controls on arm and ramps Safety of use - 2 sealed pressure safety valves - Baffle partitions - Higher safety of ball valve filling - Large volume front detritus chamber - Control manometer - Large volume stone trap Quality of manufacture - Bolted tank-chassis connection - Continuous mechanically welded unit inside and outside - Conformity to the DESP 97/23 CE (1) - Automatic welding of ferrules Compliant for road use - Approved hydraulic braking - Pneumatic or mixed pneumatic-hydraulic braking - Double lamps protected lighting - Flashing beacon support base (1) DESR : Equipment Under Pressure Directive > 0,5b injector with tines Double filling security Industrial valve Characteristics in basic version Lifting pre-equipment Stone sorter under tank Hydraulic stand Bogie Side door Bronze valve as standard Compressor oil can Tank volume (lt) * Total admissible weight (kg) ** Empty weight (kg) Tank Ø (mm) Tank thickness (mm) Baffle Level indicators Column Column Column Column Column Column Column Column Column Front valve holes D and G D and G D and G D and G D and G D and G D and G D and G D and G Base wheels 18x22,5 15x22,5 30,5R32 16x22,5 18x22,5 18x22,5 18x22,5 560/60R22,5 560/60R22,5 Standard version dimensions Tank length Overall length Overall width Overall height (*) Loss of volume with flush fitting (**) The actual on-road load corresponds to a basic material and reduces according to options 13

14 Continuous reliability and performance Compressor with to l/mn and pumping security MEC vane compressor - Nominal rate to l/min - Adjustable drip forced lubrication - Air cooling rpm drive - Kevlar pallets twice as resistant (option) - Pallet wear inspection plug STAR vane compressor - Recommended for intensive use - nominal rate to l/min - Kevlar pallets twice as resistant - Automatic lubrication for better distribution - Low pressure security - Pallet wear inspection plug WPT vane compressor - Adapted to extreme conditions - Nominal rate and l/min - Kevlar pallets twice as resistant - Automatic lubrication for better distribution - Liquid cooling with circulation pump - Electro-ventilator with temperature sensor - Low pressure security - Pallet wear inspection plug DL200 lobe compressor - Adapted to extreme conditions - Maximum work rate - Reduction of maintenance cost - Nominal rate l/min - 2 rotors 3 lobes - Without lubrication - Cooling by air injection - Suction filter with strainer - Overheating alarm - High silent air intake MEC compressor STAR compressor Compressor WPT720 Forced lubrication Pressure and low pressure security Radiator WPT Compressor DL 200 Lobe diagram DL200 Nominal rate l/min Hose Ø Gti 4500 Gti 5500 Gti 6500 Gti 8500 Gti MEC 5000 LF MEC 6500 LF MEC 8000 LF (1) (1) (1) ST 60 LA (1) (1) ST 72 LA ST 84 LA WPT 600 DR WPT 720 DR DL Standard Option (1) Possible with Security 14

15 Performances and multiple use Hydraulic generator Performance - Output from 75 to 130l/min at 180b - Gain in power - Electrical controls Multi-purpose use - Autonomous machine - Accelerator and grinder drive and machine hydraulic functions - 2 pump generator for independent compressor drive Hydraulic generator Safety of use - No oil mixture - Oil filtering - Radiator for intensive use Hydraulic radiator Hydraulic compressor drive Oil tank Combined pumping generator : pump / compressor Multi-purpose use - Pumping with the compressor - Spreading with compressor or centrifugal pump - Fitting of different compressors possible - High pressure 200b cleaner pump instead of centrifuge pump Performance - Centrifugal pump 6500 l/min at 6b when emptying - Spreading range 40 to 60 m with spreading jet Comfort of use - Rotation and hydraulic oscillation of the jet - Output adjustment valve Compressor accessories - High air intake and oil collector MEC ST - WPT - Oil can and support supplied with each machine Spreading jet Compressor oil can Garda group 6500 Compressor MEC MEC 5000LF MEC 6500LF MEC 8000LF ST 60 ST 72 ST 84 WPT 600DR WPT 720DR Pto 540 rpm Pto 1000 rpm Kevlar vanes Lubrication forced forced forced auto auto auto auto auto without Cooling Air Air Air Air Air Air Liquid Liquid Air injection Hydraulic generator 1000 rpm 2 pump generator 1000 rpm Hydraulic compressor drive GARDA generator 6500l/mn - compressor High air intake and oil collector Freewheel on transmission Homokinetic transmission Friction limiter transmission 1000rpm 15 Standard DL 200 Option

16 Central pumping arm Ø150 or Ø200 and reception cone, sequential controls central arm Ø200 accelerator central arm Ø200 accelerator Gti 8500 central arm Ø150 16

17 Simplicity and work rate at the service of comfort of use Optimised work rate - Arm section Ø150 or Pumping accelerator - Reduced setting up time - No more hose handling Innovation and multi-purpose use - Sequential control of all functions - Ø200 arm locking right and left - Reception cone with remote control closure for external pit - Hydraulic vent for arm low pressure Simplicity of use - Sequential control by 1 DE - Rapid reversal for pumping to the right or left - Cone stand on machine Safety in transport - Mechanical locking with hydraulic opening on Ø200 arm - Controlled safety valve on arm jack Ø150 and 200 Quality construction - Arm entirely galvanised - Pre-equipment on range Upkeep and reliability - Arm entirely galvanised - Swivel joint with grease nipple - Industrial valve stainless steel blade - Fixed air vent on tank central arm Industrial valve and rotating joint Ø200 arm transport locking Sequential bloc Ø200 arm hydraulic lock Cone support stand Remote control reception cone Central arm Ø150 Central arm Ø200 Right pumping Left pumping Reception cone Ø150 Reception cone Ø200 Hoses Ø150 (1 flexible + 1 rigid) Hoses Ø200 (1 flexible + 1 rigid) Reception cone remote control closure Ø150 Reception cone remote control closure Ø200 Transport locking Pumping accelerator Standard Option 17

18 Plunging pump arm Virgule Ø200 right or left, hydraulic locking arm Virgule Ø200 accelerator arm Virgule Ø200 accelerator arm Virgule Ø200 left 18

19 Performance and multiple use to optimise your work Work rate - Direct pumping into the pits - Ø200 suction tube - Optimised arm opening/closing time - Pumping accelerator not submerged - Submerged filling turbine 10 m3/min Multi-purpose use - Pumping on reception cone with adapter - Independent control of each function - Pumping with or without compressor - Industrial valve for straw slurry Comfort of use - Dual articulation - Independent control of each function - Compressor inversion by electrical jack - In cab electrical control - Valve opening coupled with air vent Safety in transport - Mechanical locking with hydraulic opening - Safety valve controlled on the jack Quality construction - Attachment of the arm on the chassis - Bearing on primary articulation - Arm isolated from the tank by bellows Upkeep and reliability - Arm entirely galvanised - Swivel joint with grease nipple - Industrial valve stainless steel blade Visibility of work Pumping on cone Transport locking Bearing Arm virgule Ø200 left Arm isolated from the tank Arm virgule Ø200 right Right pumping Left pumping A: pumping depth according to machine Up to 3.0 m Up to 3.0 m B : side offset 3.0 m 3.0 m C : chassis height 0,8 à 1m 0,8 à 1m Pumping on reception cone Ø150 Pumping on reception cone Ø 200 Pumping on remote control cone Ø150 Pumping on remote control cone Ø200 Transport locking Pumping accelerator Pumping turbine and vent Standard Option 19

20 Upper pumping arm Turbomax Ø200, rotation up to Turbo arm Turbo arm clearance 20

21 One single arm to adapt to all situations Work rate - Direct pumping into the pits - Suction hose Ø200 - Rapidity and precision of arm with motorised rotation - Pumping accelerator not submerged - Filling up to 13 m3/min in combination Multi-purpose use - Pumping to right or left - Rotation up to 320 depending on equipment - Turbomax longer Turret - Pumping into all types of pits - Pumping on reception cone with adapter - Emptying possible by the turret - Swivelling pumping arm end Comfort of use - Arm with only two articulations - Rotation by geared motor and ring - Independent control of each function - Compressor inversion by electrical jack - In cab electrical control - Lift/drop damper by nitrogen ball - Access ladder - Vent coupled with industrial valve Safety in transport - Pumping arm support right and left - Slurry collection tank with emptying valve - Column level warning light protection Quality construction - Turret guide tube inside the tank - Wide range turning joint - Ertalon guide ring inside tank - Monobloc turret Upkeep and reliability - Arm entirely galvanised - Industrial valve stainless steel blade - Ringed articulations with grease nipple Long turret Rotation by geared motor Drip tank Swivel joint Turret pumping to the right as standard Turret pumping to the left as standard A : maximum pumping depth according to machine B : side offset C : clearance height under arm Pumping on reception cone Ø150 Pumping on reception cone Ø 200 Pumping on remote control cone Ø150 Pumping on remote control cone Ø200 Turbomax long turret and motorised rotation Pumping accelerator Pumping turbine and vent Arm support Arm guide in the tank Turbo arm Ø200 3m20 to 4m 3m10 2m80 21

22 Nozzles - Té bi-nozzles: Conical nozzle, Ground level nozzle, Exact nozzle, EZ precision nozzle Exact Té bi-nozzle Ground level nozzle EZ precision Té bi-nozzle 22

23 The simplicity and efficiency of table spreading Conical nozzle - Economical spreading - Working width 12m with 1 nozzle - Working width 16m with two nozzles - Jet height up to 4m - Spreading quality sensitive to wind - Output of 1.5 to 2.3 m3 per nozzle Ground level nozzle - Multiple use and performance with all types of slurry - working width 10m with 1 nozzle - working width 15m with two nozzles - Jet height 1.5 m - output of 1.75 to 2.7 m3 per nozzle Exact nozzle - Multiple use and performance with all types of slurry - working width 10m with 1 nozzle - working width 15m with two nozzles - Jet reversed to limit drift - Interchangeable rubber end piece - output of 1.2 to 5 m3 per nozzle EZ precision nozzle - Precision and multi-purpose use - Working width 12m with 1 nozzle - Working width 16m with two nozzles - Jet height 1.5 m - Distribution plate high spreading precision - Interchangeable rubber end piece - output of 1.3 to 2.7 m3 per nozzle Adjust the dose per hectare - Output curve to adjust its speed supplied with the user s manual - 1 curve for each type of nozzle - Optimised work rate - Respect for the environment Conical nozzle Exact nozzle Desired dose m 3 /h Ground level nozzle EZ precision nozzle Flow rate curve Nozzle Exact Ø 150mm Pressure 1b, valve opening 100%, fertiliser pig slurry Forward speed km/h Nozzle working width = 10 m Flow rate curves given as an indication : Do the calculation again for each change of parameter (see method on the user s manual) Nozzle EZ Outlet Ø45 Nozzle EZ Outlet Ø60 Nozzle EZ Outlet Ø70 Nozzle EZ Outlet Ø80 Exact nozzle output curve Desired dose m 3 /h Flow rate curve Té bi-nozzle Exact Ø 150mm Pressure 1b, valve opening 100%, fertiliser pig slurry Forward speed km/h Nozzle working width = 15 m Flow rate curves given as an indication : Do the calculation again for each change of parameter (see method on the user s manual) Nozzle EZ Outlet Ø45 Nozzle EZ Outlet Ø60 Nozzle EZ Outlet Ø70 Nozzle EZ Outlet Ø80 Exact Té bi-nozzle output curve 23

24 Work rate and precision in inputs in all products up to 24 m wide Spade spreading ramps RE124, RE126, RE128, RE155, RE186, RE189, RE217, RE248 Work rate - Emptying rate up to 9 m3/min - Feed Ø150 up to 6 spades - High feed Ø200 advised as from 7 spades - Emptying accelerator on top outlet Ø150 - Ø60 hoses - Output curve for each model Quality of work - Transversal distribution of quality over 15 m3/ha - Dosimat grinder- distributor Ø60 horizontal cutting axis - Exacut Ø60 grinder- distributor 2 horizontal cutting axes - Adjustment of spade angle - Adjustment of spade height in relation to the ground - Micrometric dosing valve on cylindrical distributor - Electrical setting on rear valve - Regulation of the spreading pressure - DPA with flowmeter for Ø150 Quality construction - Fixed ramp frame on chassis - Hydraulic lifting for setting working height - Hydraulic slope corrector - Stone trap on rear outlet - Stone trap on Exacut Reliability and long life - Unit entirely galvanised - Galvanised distributor with lid Safety - Ramp end retractable according to model - Mechanical transport locking with hydraulic control - End spades retractable RE 248 Emptying rate RE 128 Setting spreading pressure Ramp locking RE 124 RE 126 RE 128 RE 155 RE 186 RE 189 RE 217 RE 248 Working width (m) Number of spades Maximum dose at 6 km/h Flow spreader with micrometric dosage valve Dosimat grinder and flow spreader Exacut grinder and flow spreader Slope corrector Feed Ø150 Feed Ø200 (1) (1) (1) (1) Standard Option (1) Fitting advised for maximum output 24

25 Simplicity and precision of spreading very large width Spreading ramps with EZ precision nozzles: RB212, RB242, RB283, RB303 Work rate - Working width up to 30 m - Emptying rate up to 7.5 m3/min - Rear outlet Ø150 up to 24 m - Rear outlet Ø200 from 21 to 30 m Quality of work - Transversal distribution of quality over 15 m3/ha - EZ precision nozzles - Adjustable nozzle plate - Reduced number of runs - Setting the spreading pressure RB m Quality construction - Tube chassis for slurry transport - Slope corrector - Feed cut-off nozzle by nozzle - Ramp 21 m can extend to 24 m Reliability and long life - Unit entirely galvanised - Monobloc arm Safety- - Mechanical transport locking with hydraulic control - Stone trap on outlet RB m Emptying rate Ramp locking Setting spreading pressure Desired dose m 3 /h Flow rate curve RB303 Flow rate curve RB303 30m 3 nozzles alim.ø200, Pressure 1b, valve opening 100%, fertiliser pig slurry RB 283 Nozzle Outlet Ø50 RB 283 Nozzle Outlet Ø60 RB 283 Nozzle Outlet Ø70 Forward speed km/h Flow rate curves given as an indication : Do the calculation again for each change of parameter (see method on the user s manual) RB 212 RB 242 RB 283 RB 303 Working width Number of nozzles Maximum dose at 6 km/h Slope corrector Feed Ø150 Feed Ø200 (1) (1) Cut off nozzle by nozzle Standard Option (1) Fitting advised for maximum output 25

26 Precision spreading and work rate in all products Hanging spreading ramps: RP12-40, RP12-48, RP16-48, RP18-48 Work rate - Emptying rate up to 8m3 /min - Feed Ø150 or Emptying accelerator on top outlet Ø or 48 outlets Ø40-1 or 2 grinder distributors Quality of work - Quality transversal distribution from 10 m3/hectare - Reduced smells - DPA with inductive flowmeter - Grinder distributor with 2 vertical cutting axes (Exacut) - Work possible on all types of crops - Hydraulic anti-drip system - Each hose guided to the soil by 2 spring rods - Constant space between hoses - Setting the spreading pressure Quality construction x 60 section ramp arm - Hydraulic slope corrector - Doubled ramp frame - Sequential control arm opening and anti-drip - Set of stands for winter storage Reliability and long life - Unit entirely galvanised - Anti-drip rotation on ertalon ring - Hoses protected in the ramp chassis Safety - Retractable ramp end - Mechanical transport locking with hydraulic control - Stone trap on outlet and on grinder RP Anti-drip jack Setting spreading pressure RP Traffic signs RP RP Security for ends Ramp locking RP RP Working width (m) Number of outlets Ø Maximum dose at 6km/h (Ø150) Exacut grinder and flow spreader Option 2 Exacut 30s Slope corrector Feed Ø150 Feed Ø200 Standard Option 26

27 Optimised mechanisation costs and reduced fertiliser input Injector with square tines or vibroflex: EDC33-11, EDC33-13, EDV 39-13, EDV45-15, EDV51-17, EDV57-19 Work rate - Emptying rate up to 5m3 /min - Feed Ø150 - Up to 5.7 m of working width - Power of 8-10CV needed per metre Quality of work - Quality transversal distribution at 10m3/ha - Better distribution with 3 cm interrow - Automatic control of the dose spread - Elimination of smells and nitrogen losses - Distributor and micrometric dosage valve as standard - Double effect lifting with nitrogen balls to follow the terrain - Depth control by gauge wheels or rollers - Depth gauge at front of tank - Dosimat Ø60 grinder distributor - Exacut Ø60 grinder distributor Quality construction - Tube chassis 100 x 100 x 8 - Galvanised chassis - hydraulic folding - Slurry injector bit integral to the tine - Tines spread over 2 rows - Large clearance under chassis - Inter-row of 80 cm front and rear Reliability and long life - Square tines 25 mm for deep work - Vibroflex tines for surface work Safety - Transport traffic signs - System for automatic reversal of rotation if there is a blockage EDV Injector with vibroflex tines + roller Micrometric dosage valve EDV tine work Square tine 35 EDC EDC EDV EDV EDV EDV EDV Working width (m) 3,3 3,3 3,9 4,5 5,1 5,7 6,5 Number of tines Inter row (m) 0,3 0,25 0,3 0,3 0,3 0,3 0,5 Square tines 35 Vibroflex tines Metallic gauge wheels Bar roller Ø500 Flow spreader with micrometric dosage valve Dosimat grinder and flow spreader (1) (1) (1) (1) Exacut grinder and flow spreader (1) (1) (1) (1) Standard Option (1) Fitting advised for good distribution 27

28 Injector with oblique disks Ø630 mixed or special for grassland EDS24-4, EDS36-6, EDS48-8, EDS60-10, EDD33-11, EDD39-13, EDD45-15, EDD51-17, EDD57-19 EDD Work EDS 48-8 Work Soil cross-section after injection 28

29 The limits of disc injection pushed to the extreme Work rate - Emptying rate up to 5m3 /min - Feed Ø150 - Work up to 6m wide - Power of 5-6CV needed per metre - Non-stop security per element - Large clearance under chassis Quality of work - Side distribution of slurry up to 15 cm - Swivel drawbar for follow-through in a bend - Work depth from 6 to 10 cm - Quality transversal distribution from 10m3 /ha - 30 cm inter-row special for grassland - 60 cm inter-row for mixed grassland and stubble - No slurry run-off on slopes - Automatic control of the dose spread - Elimination of smells and nitrogen losses - Standard distributor and micrometric dosage valve - Dosimat grinder- distributor Ø60 horizontal cutting axis - Exacut Ø60 grinder- distributor 2 horizontal cutting axes - Setting the spreading pressure - Output curve to adjust its dose Quality construction - Tube chassis 100 x 100 x 8 - Hydraulic folding - 1 or 2 rows of discs - Double effect lifting with nitrogen balls to follow the terrain - Floating position on lifting - Depth control by 2 or 4 gauge wheels - Soil depth indicator at front of tank Reliability and long life - Galvanised chassis - Ring axles with grease points - Disc hubs 2 conical bearings - Rubbing parts on down tube made of anti-wear steel - Galvanised distributor with lid Safety - Transport traffic signs - System for automatic reversal of rotation if there is a blockage - Non-stop security per element Soil after injection Crop profile Traffic signs Soil depth indicator Setting spreading pressure EDS output curve Desired dose m 3 /h Flow rate curve 1 row Disc Injectors Alim.Ø150, Pressure 1b, valve opening 100%, fertiliser pig slurry Micrometric dosage valve Forward speed km/h EDS 24-4 EDS 36-6 EDS 48-8 Hydraulic folding EDS EDD EDD EDD EDD Working width (m) 2,4 3,6 4,8 6 3,3 3,9 4,5 5,1 5,7 Number of disc Inter row (m) 0,6 0,6 0,6 0,6 0,3 0,3 0,3 0,3 0,3 Hydraulic folding Metallic gauge wheels Distributor with micrometric dosage valve Dosimat grinder distributor (1) (1) (1) (1) (1) Exacut grinder distributor (1) (1) (1) (1) (1) Swivel drawbar (follow-through in a bend) Standard Option (1) Fitting advised for good distribution EDS 24 4 EDS 36 6 EDS 48 8 EDS Maximum values : Flow rate reduction possible with pressure and valve opening Flow rate curves given as an indication : Do the calculation again for each change of parameter (see method on the user s manual) EDD

30 DPAE with inductive flowmeter Ø150 Precision of inputs - Automatic management of dose / ha spread - Variation < 5% in relation to the programmed dose - Output regulation independent of pressure in the tank and type of slurry - Instantaneous flow control by inductive flowmeter - Speed sensor on tanker wheel - Grinder-distributor speed sensor - Compressor speed sensor - Very good longitudinal distribution Innovation - Compatible with precision farming - Coupling possible with GPS guide bar - Automatic cut-off of rear valve or sections by GPS Driving comfort - Instant display of the dose / ha spread - 2 instructions only to record :working width and desired dose per hectare - Low / high speed alarm - Grinder distributor blockage alarm - Simple intuitive use of the box - Use in manual for nozzle spreading Traceability - 10 customer files can be recorded (Name, M3 spread, Time, Distance, Surface) - Data can be exported in excel or html format - Printer in cab - Automatic cut-off of rear valve or sections by GPS Reliability and long life - Unit galvanised and integrated into the tank - Flowmeter Ø150 protected in the tank - Manual control of the selected valve - Flowmeter in non-corrosive materials Flowmeter integrated into the tank SMART Control control box Simple control box Inductive flowmeter Flowmeter operation Meter N Name Volume [m 3 ] Surface [ha] : Distance [km] Duration 1 Customer 1 153,5 5,15 12, Customer 2 439,24 17,56 53, Customer Customer Customer Customer Customer Customer Customer Customer Compteur total Volume [m 3 ] Surface [ha] : Duration 12823,5 427,53 248,23 Meter data exported 30

31 How to choose your controls on a slurry tanker As standard: control of the spreading valve and of the reversing of the compressor direct from the tractor. Table of needs: Description of hydraulic functions Required flow rate Direct tractor coupling Jack functions l/min Electro-hydraulic distributor Engine functions up to 130l / min Bronze rear valve Single effect jack SE 20 l/min 1 1 X Rear industrial valve Double effect jack DE 20 l/min 1 1 X Front central arm Ø 150 or 200 VIRGULE arm Ø200 Compressor inversion Arm Valve + vent Electric compressor inversion Valve + vent Arm articulation Plunger articulation Electric compressor inversion DE 20 l/min 1 1 X DE 20 l/min X 3 X Valve + vent Turbo arm Ø200 Arm rotation DE 20 l/min X 4 X Arm lifting/lowering Plunger articulation Pumping accelerator Engine SE 70 l/min 1 X 1 Pumping turbine 6 m3/min Engine SE 70 l/min 1 X 1 Pumping turbine 10 m3/min Engine SE 120 l/min X X 1 Grinder-Distributor (Dosimat/Exacut) 2 stroke engine DE 60 l/min 1 X 1 Upper loading cone Valve + vent DE 20 l/min 1 1 X Hydraulic opening Ø600 Jacks DE 20 l/min 1 1 X Mountain emptying Bronze valve DE 20 l/min 1 1 X Lifting Jacks DE 20 l/min 1 1 X Spade ramp Folding + locking DE 20 l/min 1 1 X Nozzle ramp Folding + locking DE 20 l/min 1 1 X Hanging ramp (Do not forget engine function for Exacut) Folding + locking DE 20 l/min 1 1 X Ramp drift corrector Oscillation jack DE 20 l/min 1 1 X Injector folding body Folding DE 20 l/min 1 1 X Spreading jet Rotation (engine) Oscillation DE 20 l/min 2 2 X Following axle Locking jacks SE ou DE 20 l/min 1 X X Total * DE = Double Effect Function SE = Single Effect Function X = Impossible * = prévoir 1 SE supplémentaire sur le tracteur si distributeur électro-hydraulique 2 distribution blocks with electric controls: - from 2 to 6 hydraulic cylinder functions with a maximum oil flow rate of 45 l/m - from 2 to 11 hydraulic cylinder functions with a maximum oil flow rate of 45 l/m plus 1 or 2 engine functions with a maximum oil flow rate of 130 l/m 2 electric controls boxes are available BASIC or SMART: The BASIC control box allows to control the totality of the tanker from the tractor cab. Available from 2 to 13 electrohydraulic functions including 2 high flow functions The SMART controls include a DPA system as well as a display with informations of time, surface, total volume, volume per hectare, and kilometres driven. The SMART controls features all the BASIC control functions BASIC control box SMART control box 31

32 Accessories Loading cone - Valve Ø200 for load - Valve Ø150 for air vent - Hydraulic simultaneous control - Access ladder Top opening Ø600 - Hydraulic opening / closing - Drop frame loading height - Access ladder High emptying arm - Hydraulic rotation Hydraulic valve Ø150 or Drip tank Dosimat - Grinder 1 horizontal cutting side - Regular distribution of slurry - Air suction shutter to stop pulsations - Special rotor for injector - Special rotor for spade ramp - Outlets Ø60 - Feed Ø150 on LV9 - Feed Ø150 or 200 on LV13-LV24 - System for automatic reversal of rotation if there is a blockage (option) Exacut - Grinder 2 vertical cutting sides - Suitable for slurry with straw or feathers - Air suction shutter to stop pulsations - Regular distribution of slurry - Feed Ø150 or Special counter blades for injector - Special counter blades for ramp - Outlets Ø40 (hanging) or Ø60 (injectors-spade ramps) - Integral stone trap - System for automatic reversal of rotation if there is a blockage (option) Loading cone Top opening Ø600 Top opening Ø600 High emptying arm Drip tank Dosimat Exacut outlets Ø60 Exacut outlets Ø40 Hydraulic connection rear 32

33 Accessories Semi-automatic manual coupling - Handle with easy grab coupling - Ø150 or 200 Suction strainer - Avoids sucking up foreign bodies - Advised with ramp and injector - Ø150 or 200 Direct spreading bend - Spreading at the nozzle without uncoupling the injector - Bend Ø150 with angle adjustment Semi-automatic coupling Suction strainer Stone sorter under tank - Large volume 14l - Plug Ø200 or drain valve Stone sorter on rear outlet - Drain plug Ø150 pneumatic interior mixer - Ø80 for MEC8000 and ST60 - Ø100 for ST72 and more - High performance mixing of slurry - Slurry homogenised during spreading - Tank walls swept by expulsion of compressor air Stone trap on rear outlet Direct spreading bend Stone sorter under tank Weight transfer partition - Keeps weight at the front of the tank until spreading ends - Automatic starting system Galvanised mudguard - 1, 2 or 3 axles - Integral hose support base Pneumatic interior mixer Hose support under chassis - For tanker flush fitting axle Weight transfer partition Hose support under chassis Galvanised mudguards 33

34 Accessories Working headlight support base- Dual lighting - Top of tank or on injector as option Side lights - 4 lights front and rear Bull bars - Galvanised (for Export) Meter - Compressor rotation time - Kilometric Waterproof tool box x 400 x 500 polypropylene - 2 handles with key locking Hand-washing can - 30l with pump for soap Cleaning kit - 5 m of hose Ø60 - Connection on valve Ø150 - Cleaning tube with 1/4 turn valve High pressure jet washing equipment - Wide choice of equipment available - Equipment on Gti and ranges - Partitioned tank clean water / slurrymud - Hydraulic winder for hose Ø60 or Ø80 - HP hose winder - Flexible cleaning cable - GardaJet High Pressure unit 136l/mn- 200b mechanical drive - Remote control 1 to 10 functions (valve, winder, etc) Support base for working headlights Remote control Side marker lights front Bull bars Time meter 10 remote control functions Side marker lights rear Kilometric meter Toolbox Hand-washing can Cleaning kit Dual lighting Design of power jet washing machine Hydraulic winder 34

35 Wheel characteristics XY1 AR01 TR Cargo Twin Radial 421 ELS XS large Dimensions Make Profile N of plys load index TYRE CARACTERISTICS Diameter in mm Width in mm Load per wheel in kg 40km/h Inflation pressure in Bars 15x22,5 Retrad XY ,0 16x22,5 Retrad XY ,0 18x22,5 Retrad XY ,0 18R22,5 Mitas new AR F ,0 550/60x22.5 Mitas TR ,8 550/60x22.5 Alliance A ,0 560/60x22.5 Trelleborg A ,6 560/60R22.5 Alliance 380 radial 161 E ,0 560/60R22.5 Michelin Cargo radial 161 D ,0 580/65R22.5 Trelleborg Twin radial radial 159 D ,2 600/50x22.5 Trelleborg A ,6 600/55R22.5 Alliance 380 radial 162 E ,0 600/55X26,5 Trelleborg A ,4 600/55 R26.5 Trelleborg Twin Radial radial 165 D ,0 600/55R26.5 Michelin Cargo radial 165 D ,0 650/55R26,5 Alliance 380 radial 167 E ,0 24R20.5 Michelin XS large radial 176 F ,0 650/65R26.5 Nokian ELS radial 174 D ,0 650/65R26.5 Alliance 380 radial 174 D ,0 680/55R26.5 Trelleborg Twin radial radial 165 D ,2 600/60x30.5 Trelleborg A ,1 600/60R30.5 Michelin Cargo radial 169 D ,0 710/45x26.5 Trelleborg A ,1 710/50R26.5 Michelin Cargo radial 170 D ,0 710/50R26.5 Alliance 390 radial 172 D ,0 650/65R30.5 Trelleborg Twin Radial radial 176 D ,0 650/65R30.5 Michelin Cargo radial 176 D ,0 750/60x30.5 Trelleborg 404 radial 178 A ,6 750/60R30.5 Trelleborg Twin Radial radial 181 D ,0 650/60R34 Nokian ELS radial 175D ,0 710/55R34 Nokian ELS radial 177D ,0 800/45x30.5 Trelleborg 404 radial 178 A ,1 30,5LR32 Alliance 390 radial 181B ,0 18,4/15x34 Alliance ,0 21,3R24 Dnieproshina tracteur radial ,8 23,1X26 Alliance ,8 620/75R26,5 Alliance 375 radial 166 A ,8 28,1R26 Dnieproshina tracteur radial 157 A ,8 24,5X32 Alliance A ,0 30,5R32 Dnieproshina tracteur radial 161 A ,8 30,5LR32 Alliance A 360 radial 178 A ,7 35

36 Gti 4500 Gti 5500 Approval DREAL 25 km/h Approval DREAL40 km/h Tank Flush fitting axle Rear door Ø 900 mm Side door Ø 600 mm instead of rear Spring drawbar Mudguards High volume pumping safety Column level indicator Ø 110 mm Lifting pre-equipment and central pumping arm Pumping Side front valve Ø 150 mm or Ø 200 mm Semi-automatic hooking system Central pumping arm Ø 150 mm with reception cone Central pumping arm Ø 200 mm with reception cone Front upturned pumping arm Ø 200 mm Pumping arm TURBOMAX Ø 200 mm Pump accelerator on pumping arm Ø 200 mm Submerged pumping turbine 6m3/mn + vent Submerged pumping turbine 10m3/mn + vent Upper filling cone Ø 200 mm + Ø 150 mm Hydraulic upper filling hatch Ø 600 mm Receiving cone (Ø 150 mm or Ø 200 mm) Receiving cone closing with remote control (Ø 150 mm or Ø 200 mm) Suction strainer Bend 45 (Ø 150 mm or Ø 200 mm) Bend 90 (Ø 150 mm or Ø 200 mm) Galvanised pumping tube 3m (Ø 150 mm or Ø 200 mm) Flexible pumping tube 3m (Ø 150 mm or Ø 200 mm) Hose support under chassis Compressor MEC 5000lt/mn MEC 6500lt/mn MEC 8000lt/mn STAR lt/mn Kevlar vanes STAR lt/mn Kevlar vanes STAR lt/mn Kevlar vanes WPT lt/mn Liquid cooling WPT lt/mn Liquid cooling DL lt/mn lobe compressor Compressor group + Thrust pump unit with cannon High air intake and oil recuperator Drive shaft - with flywheel Drive shaft - friction torque limiter Drive shaft - with wide-angle joint Hydraulic compressor drive Spreading Industrial rear valve Ø150 or Ø200 Ground level nozzle Exact nozzle EZ precision nozzle Té bi-ground level nozzle Hydraulic hitch Rear high outlet Ø 150 or 200 mm with stone remover under the tank Stone remover (alone) with emptying plug Stone remover on rear outlet Ø 150 mm with cap Spreading booms with spades 12 to 24 m Nozzles booms 21 and 24 m Nozzles booms 28 m Nozzles booms 30 m Hanging booms 12 m Hanging booms 16 m Hanging booms 18 m Tines injectors up to 5,70 m Disc injectors up to 6 m Grinder-ditributor Dosimat Grinder-ditributor Exacut DPAE (electronic flow rate proportional to speed) with inductive flow metre Printer for DPAE Controls Electric controls up to 10 functions Electric controls grinder-ditributor Option load sensing distributor (LS) On board hydraulic pump 75lt/mn Autonomous on board hydraulic pump 140lt/mn + 75lt/mn Hydraulic cooling system (intensive use) Accessories Mechanical stand Hydraulic stand Bolted ring coupling ball K80 3 ton Time meter Side marker lights Rear support base for working headlights Cleaning kit 5m Ø60 Compressor oil can 5L with support Waterproof toolbox Hand-washing can 30l Standard Option Gti 6500 Gti 8500 Gti Tridem Tridem Photos not contractual Except for typographical errors the technical characteristics are given as an indication and not as a commitment, the Jeantil Company reserving the right to make all modifications, improvements and developments to them. The 1 st complete solution Livestock Transport Spreading SCM JEANTIL Z.I. des Charmilles SAINT AIGNAN SUR ROË Tél: Fax: Site Website: scm@jeantil.com