WHISPERWAVE Panels, Baffles, Ceiling Clouds and Awnings Installation Instructions

Size: px

Start display at page:

Download "WHISPERWAVE Panels, Baffles, Ceiling Clouds and Awnings Installation Instructions"

Laurence Howard
6 years ago
Views:

Panels, Baffles, Ceiling Clouds and Awnings Corkscrews WHISPERWAVE clouds are

press down firmly and turn the corkscrew clockwise until the top of the coil is

1 Panels, Baffles, Ceiling Clouds and Awnings Corkscrews WHISPERWAVE clouds are usually shipped with four short stainless steel corkscrews for hanger wire suspension. Vertical Suspended Baffle Applications Place at suspension points where necessary, press down firmly and turn the corkscrew clockwise until the top of the coil is completely seated along the top of the baffle. Depending on overall panel lengths, 2 or 3 long corkscrews are usually shipped for vertically suspended WHISPERWAVE applications. [ 1 ]

Horizontal Suspended S-Shaped Cloud Applications To find the approximate distances away from the sides to install the corkscrew hangers, multiply the width and length by 0.20.

PLAN VIEW Each square = 1' 0" + = Suspension points 48" 1) Between 9" to 12" in from sides (48" width) 2) Between 18" to 24" in from front and back (96" length) 96" 3) Keep wires plumb ELEVATION VIEW

2 Horizontal Suspended S-Shaped Cloud Applications To find the approximate distances away from the sides to install the corkscrew hangers, multiply the width and length by Four points are usually all that is necessary to suspend ceiling clouds in place. Keep corkscrews, hanger wires and anchors overtop in exact alignment, true and plumb. PLAN VIEW Each square = 1' 0" + = Suspension points 48" 1) Between 9" to 12" in from sides (48" width) 2) Between 18" to 24" in from front and back (96" length) 96" 3) Keep wires plumb ELEVATION VIEW R " 57.5" 19.25" 9.5" 29" 9.5" 9.5" 4.75" 48" 29" 24" 14.5" 9.5" 4.75" 96" 4' x 8' S-Shaped Clouds Set the corkscrew hangers 9-1/2" away from the sides and 19-1/4" in the front and back of the cloud. 2' x 4' S-Shaped Clouds Set the corkscrew hangers 4-3/4" away from the sides and 9-1/2" in the front and back of the cloud. 48" [ 2 ]

WHISPERWAVE clouds multiply the width and

20 to determine approximate distances to set

3 Corkscrews with Light-gauge Hanger Wire Suspension Applications For custom convex WHISPERWAVE clouds multiply the width and length by 0.20 to determine approximate distances to set corkscrew hangers away from the sides, front and back. Miscellaneous Suspension Accessories Please consult pinta acoustic for technical assistance to suit your specific project requirements. [ 3 ]

T-slot, Main Runner Suspended Front-to-Back Cloud Pairs T-slot, Main

ganged suspension applications using standard 15/16" main runners.

4 T-slot, Main Runner Suspended Front-to-Back Cloud Pairs T-slot, Main Runner Suspended Side-by-Side Cloud Pairs Custom flat WHISPERWAVE clouds. Custom s-shape WHISPERWAVE clouds. T-slot, Main Runner Detail Setup T-slot, Main Runner Suspension Suspension options with WHISPERWAVE clouds. WHISPERWAVE clouds can be custom produced with factorycut T-slots for ganged suspension applications using standard 15/16" main runners. Slide the main runners through the T-slots into position as required. Please consult pinta acoustic for technical assistance to suit your specific project requirements. [ 4 ]

15/16" Main Runners Cut the main runners back to suit cloud. Taper the ends and back-cut the bottom flange corners to help slide through t-slots easily.

5 15/16" Main Runners Cut the main runners back to suit cloud. Taper the ends and back-cut the bottom flange corners to help slide through t-slots easily. T-slot, Main Runner Suspension Cut the main runners back approximately 3" to 4" from the sides and inset hanger wires plumb to cantilever and balance the cloud correctly. Keep wires as invisible from view as possible. T-slot, Main Runner Suspension The t-slot, main runner installation method allows carpenters to quickly join s-shape WHISPERWAVE clouds side by side on the bench before being suspended together for faster installation times. Please consult pinta acoustic for technical assistance to suit your specific project requirements. [ 5 ]

WHISPERWAVE Ribbon Wall Panel Direct-Apply Installations Using acoustic Adhesive Substrates must be clean,

Cut the tube end to produce a 1/4"-diameter bead of adhesive. Apply beads of adhesive as shown.

Hold the panel in position for 5 seconds.

exposure to the air. Then press the panel back into position.

continuous panel rows, use white hot-melt glue between ends to ensure the seams remain tight.

6 WHISPERWAVE Ribbon Wall Panel Direct-Apply Installations Using acoustic Adhesive Substrates must be clean, dust- and oil-free. Prep surfaces to ensure the best bond. Cut the tube end to produce a 1/4"-diameter bead of adhesive. Apply beads of adhesive as shown. Gently slide the panel into position side to side and up and down. Press onto the substrate. Hold the panel in position for 5 seconds. If necessary, remove panels from the surface for about one minute to allow the adhesive to become tacky with exposure to the air. Then press the panel back into position. Perforated base (adhesive required) Stick pins, optional (not by pinta acoustic) 2" 2" When creating continuous panel rows, use white hot-melt glue between ends to ensure the seams remain tight. Hot-melt glue accessories not provided by pinta acoustic. Please consult pinta acoustic for technical assistance to help plan your specific project requirements th Avenue North, Suite 400 n Minneapolis, MN n Toll-Free 2014 pinta elements GmbH. All rights reserved. 09/14 pinta acoustic, inc. is a company of pinta elements GmbH.

2004 SERVICE MANUAL Six Six Sport Avenue Stanford, Valencia, California fax

2004 SERVICE MANUAL Six Six Sport 28209 Avenue Stanford, Valencia, California 91355 661 257-4411 fax 661 294-4179 www.answerproducts.com Table of Contents Description Page Introduction 3 Front Suspension