INSTALLATION MANUAL COUPLED SHADE PRODUCT OVERVIEW. 1. Idle End Shade

Transcription

1 INSTALLATION MANUAL COUPLED SHADE PRODUCT OVERVIEW 1. Idle End Shade Intermediate Bracket 3. Drive End Shade 4. Clutch 5. Stop Bead (attached in field) 6. Stainless Steel Bead Chain 1 7. Chain Connector 8. Chain Guide Heat-Sealed Hem Pocket 10. 4" Fascia 11. 4" Fascia Clip " Fascia Bracket Cover 13. 4" Fascia Brackets 10 11

2 STANDARD BRACKET 4" FASCIA BRACKET Install brackets JAMB MOUNT JAMB MOUNT 1. Use a minimum of 2 fasteners suitable for the mounting surface per bracket. 2. Mount control, intermediate, and idle brackets. NOTE: The open end of each bracket faces downward, as shown in the drawing. TOP MOUNT TOP MOUNT WALL MOUNT WALL MOUNT INTERMEDIATE BRACKET NOTE: If using a wall mount bracket as an intermediate bracket in this case, the wall mount bracket will need to be shimmed out. TOP MOUNT WALL MOUNT

3 INTERMEDIATE BRACKET COMPONENTS 1. Drive Shade Link System Housing 3. Locking Tab 4. Link J Bracket 5. Bearing 6. Ring 7. Drive Pin 8. Grip Wheel 9. Intermediate/Idle Shade 10. Infinite Adjuster SHADE PREPARATION Bearing Link System Housing 1. Insert bearing onto the drive pin. (see Figure 1.) Drive Pin 2. Insert the drive pin, bearing end first, into the drive shade Drive Shade link system housing. (See.) Figure 1 Ring Note: Ring must be on the side of the bearing closer to Ring Infinite Adjuster the idle shade. Incorrect ring placement will cause shade control issues. Drive Pin Intermediate/Idle Shade Figure 3 3. Insert the drive pin into the intermediate or idle shade. (See Figure 3.) Note: for larger shades, two people may be required for installation

4 SHADE INSTALLATION Bearing 1. Align and hook the clutch into the drive end bracket. (See Figure 1.) Clutch Figure 1 Bridge Link J Bracket 2. Mount bearing onto the link J-bracket. (See.) 3. Compress idle end plug on the inside section of the bracket. Slide the idle end up the bracket ramp into the center hole (See Figure 3.) 4. Check that idle pin and clutch hooks are fully seated in each bracket. (See Figures 4a and 4b.) Figure 3 Figure 4a 5. Insert the locking tab onto the link J-bracket to hold the drive in the bracket. (See Figures 5a and 5b.) Figure 4b Link J Bracket Locking Tab Figure 5a (top mount) Figure 5b (wall mount)

5 FASCIA CLIP INSTALLATION Flange Angled Tab 1. Insert the 4" fascia clip through the bottom slot on the face of the bracket. (See Figure 1.) 2. Press firmly on the clip until the bracket is seated behind the angled tab. (See.) Figure 1

6 HEM BAR ADJUSTMENT Octagonal Grip Wheel Infinite Adjuster 1. Align shade height by using the octagonal grip wheel on the infinite adjuster. 2. Start with the shade adjacent to the drive end shade and work towards idle end shade. Figure 1 3. Hold drive end shade with one hand and turn the octagonal grip wheel until the shade heights are aligned. Figure 3

7 FASCIA INSTALLATION Figure 1 1. Hook the fascia to the top of the bracket. (See Figure 1.) 2. Gently press at the bottom until the fascia fully snaps onto the bracket. Note: Fascia brackets may have to be lowered if head is not level. 3. Attach fascia bracket cover. Prepare bracket by cleaning debris and dust. Remove adhesive backing from bracket cover and attach to bracket. (See.)

8 CHAIN GUIDE INSTALLATION IMPORTANT: Chain guide must be installed for proper shade operation. 1. Unwrap control chain loop and determine a mounting location for the guide on the wall or jamb. 2. With the control chain loop under minimal tension, compress the guide and install screw. WARNING: The chain guide reduces the hazards of strangulation and entanglement of young children by limiting access to the control chain. SET UPPER/LOWER LIMITS Stop Bead Stainless Steel Bead Chain 1. Roll shade to lower limit position. 2. Attach stop bead next to the clutch on the front of the chain of a regular roll shade or the back of the chain of a reverse roll shade. 3. Raise the shade to its upper limit position, and attach the stop bead next to the clutch on the back of the chain of a regular roll shade or the front of the chain of a reverse roll shade. OPERATION Pull chain in front to raise shade; pull chain in back to lower shade. The opposite is true for reverse roll.

9 MAINTENANCE Lightly vacuum panels with a soft brush attachment or wipe with a duster. Do not use liquid cleaning solutions. Shades may also be gently wiped with a clean damp cloth. Allow the shade to dry completely before raising. Do NOT completely immerse.