Spikes-Spider Hub Installation
|
|
- Christopher Anderson
- 6 years ago
- Views:
Transcription
1 Spikes-Spider Hub Installation The instructions that are provided with the Spikes Spiders are pretty good. I've created this page for two reasons: to show those that are thinking of buying a set exactly what it looks like to install them, and to show Saturn Vue owners exactly which pieces are used for the installation since the provided instructions are more generic in nature. These instructions are for installing the Spikes-Spider wheel hubs on '06 and '07 FWD Vues with 17 inch wheels and the OEM Bridgestone Duellers (235/65/17). The installation takes about 20 miutes: 1. Ensure that you have the right size Sport chains and Adapter Kit.
2 2. Remove the center hub cover from the two front wheels: Turn the plastic nuts on the hub cover counter clockwise. You can use a socket or the jack handle wrench that comes with the vehicle. I chose to use a socket and was pleasantly surprised to see that I can finger loosen the plastic nuts without using a wrench. The plastic nuts do not separate from the hub, you simply need to turn them about 3 or four turns counter clockwise.
3 Once all five nuts are loose wiggle the cover a little and it should simply fall off in your hand. Save the center cover for the day you remove the Spikes-Spider Hub. You won't need it any more for this installation. 3. Retrieve the Spikes-Spider Adapter (Hub) Kit hardware from the Spikes-Spider box: This is the small Spikes Spider Adapter box that rests inside the larger shipping box.
4 You will find the locking hubs, covers, bolts, spacers, fix clips, and instructions. 4. Install the fix clips on the lug nuts: The fix clips come in pairs for each lug nut
5 The slotted fix clip slides over the lug nut. It should sit firmly against the outer threads on the lug nuts but do NOT slide them over the outer threads. Slide the smooth cover over the fix clip. Do the same for all five lug nuts on the wheel.
6 5. Determine the correct spacer and bolt combination to use for the mounting hardware: The instructions explain how to determine which spacers and bolts to use. You will use a card and tab that is part of the instructions. If you have an '06 or '07 Vue with the OEM Bridgestone Dueller tires, take my word for it that you need the short spacer, the long bolt, and the nylon washer for each lug. If you are using other wheels, tires, or another vehicle you will simply need to follow the instructions on the card. 6. Secure the Fix Clips on the lug nuts. Use the short spacers to fasten the Fix Clips to the lug nuts.
7 Insert the short spacer threads into the Fix Clip covers and finger tighten them on all five lug nuts. Don't worry about finger tightening them too tight, these will take a lot of torque before they are ready to go. After all the spacers are finger tight, use the supplied socket tool and torque lever to tighten the spacers on the Fix Clips.
8 The torque lever is designed so that when the opposite ends of the loop touch each other you have the right amount of torque on the spacer. Do NOT continue to tighten the spacer with more force. By the way, at this point I would highly recommend grabbing a cloth and wiping down the wheels if you haven't already done so. I waited until I had the hub installed to get all the dust off that you see in these pictures and ended up with some nice cuts across the back of my hand from the hub plate. Oh well, no big deal... I've yet to do an accessory task without putting blood and sweat into it. 7. Attach the long bolts and nylon spacers to the Hub Plate: Insert the long bolts through the slots adjacent to the number 5. The top slot will have 3, 4, and 5 stamped around it. The rest of the slots you want to use will have just the number 5 stamped by it. (The number 5 represents the number of lugs on the wheel. The number 4 slots would be for four lug wheels, the number 3 for three lug wheels.
9 Slide the nylon spacers onto the threaded part of the bolt that is sticking out the back side of the plate. This will hold the bolts on the plate for the next step. 8. Attach the hub plate to the spacers on the Fix Clips: Starting at the top with the 3, 4, 5 slot, screw the bolt into the topmost spacer. Only screw it in enough for it to stay in place. The looser you leave it the easier it will be to get the rest of the bolts started. Once all 5 bolts are started, tighten them all down with the same supplied socket and torque lever tool.
10 To finish off the job install the black Hub Cover onto the hub plate by centering it, twisting it until you feel it slide into the locking mechanism and then twisting it in place. Voila! Finished and ready to head out on the road. I recommend hanging on to all the spare bolts and spacers that came with the kit. You never know when you might have another vehicle to which you want to attach the Spike-Spiders. I put all the extra hardware and the torque tool into a ZipLoc baggie and put it with the orignal wheel center covers in the blue box that used to containd the Spike-Spiders attachment kit. I'll be ready for the spring when it's time to remove the attachments.
J&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions
J&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions The below installation instructions work for the following products: J&M Mustang Adjustable Panhard Rod (05-09) Please read through
More informationHow to Change Front Brake Pads on a Toyota Corolla
How to Change Front Brake Pads on a Toyota Corolla Link to this article on (All other links in this document are disabled) Follow this picture guide to change the front brake pads on a 2003-2008 Toyota
More informationThis is an aluminum-case PowerGlide Transmission out of a 1966 Chevelle.
Removal Procedures ***Take a picture of the transmission and note the lever positions (Transmission Arm Lever points up and Kickdown Lever point down)*** This is an aluminum-case PowerGlide Transmission
More informationSteeda Bumpsteer Kit (94-04) - Installation Instructions
Steeda Bumpsteer Kit (94-04) - Installation Instructions The below installation instructions work for the following products: Steeda Bumpsteer Kit (94-04) Please read through the instructions carefully
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationSTEP #1: Remove the wheels from the truck. There are (6) 21mm lug nuts holding each wheel on... Remember Lefty Loosy, Righty Tighty.
- CustomTacos.com Page 1 of 36 How-To: Toytec Lift Install Read all of these install instructions prior to installing Toytec's suspension lift. I cannot be held responsible for any damages or personal
More informationThis guide will explain how to remove the old springs from the car and replace them with lowering springs.
fubar Guide: Fitting lowering springs to the Mk2 Clio The method described below worked for me. I am not saying it is the only method to complete the task. I will not accept any responsibility for damage
More informationLoD Offroad. Jeep JK Rear Bumper with Tire Carrier Installation Instructions
LoD Offroad Jeep JK Rear Bumper with Tire Carrier Installation Instructions Please read through the instructions before beginning any part of the installation process. Packaging List: 1-Rear Bumper 1-Tire
More informationReplacement Front Outer Tie Rod End (85-93 All)
Replacement Front Outer Tie Rod End (85-93 All) Materials in the box: One outer tie rod end, castle nut, cotter pin, nut, and grease fitting. Tools Needed: Jack and Jack Stands Pry bar (you may or may
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationInstallation Guide for Rough Country 2.5 inch Lift Kit w/o Shocks (07-15 Wrangler JK) Item # J10212
Installation Guide for Rough Country 2.5 inch Lift Kit w/o Shocks (07-15 Wrangler JK) Item # J10212 Installation Time: 3 Hours Tools Required: Jack (2 helps, but not needed) Jack stands(2 3-ton, 2 2-ton)
More informationLoD Offroad. Jeep JK Door Linked Rear Bumper with Tire Carrier Installation Instructions
LoD Offroad Jeep JK Door Linked Rear Bumper with Tire Carrier Installation Instructions Please read through the instructions before beginning any part of the installation process. Packaging List: 1-Rear
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationRS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.
RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR 2007-2016 JEEP WRANGLER ALL MODELS. Rear Bumper Installation Instructions 1) Remove factory rear bumper, (this includes all tow hitch
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationBEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationBy AM Customer: Dean Smith, Aug. 8, 2014.
Ford Racing Bullitt Axle-Back Exhaust (05-09 GT, GT500) By AM Customer: Dean Smith, Aug. 8, 2014. Tools for the Job: 13mm Wrench 13mm Socket 15mm Socket 15mm Deep Socket Ratchet(s) [I used a bigger one
More information2. With the rear door open remove pull-style clip from the passenger side just below the door latch.
LoD Offroad FJ Cruiser Rear Bumper with Tire Carrier Installation Instructions 1. Begin with removing factory spare from the rear door. 2. With the rear door open remove pull-style clip from the passenger
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More information2001 V70 T5 ETM Removal and Cleaning Directions
2001 V70 T5 ETM Removal and Cleaning Directions Howard Cheng howardc64@gmail.com 10/24/05 Version 1.4 Read this before you start I performed this ETM cleaning because I had gotten 2 reduced performance
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More information2001 BMW X5 4.4i. Fuel Filter Replacement
P P 2001 BMW X5 4.4i Fuel Filter Replacement Symptoms for Replacement: OBDII code P0171, Lean Bank1, which could be a bad or dirty MAF sensor Sluggish engine performance including hesitation with Wide
More informationNEW BRAKE INSTALLATION. Let us show you how a
Tech Article From Newsletter 17.2-2nd Quarter of 2011 NEW BRAKE INSTALLATION Let us show you how a Big Brake Install is easier than you think!! So, you have a 572 (or a hot 383) in your shoebox... you
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More informationReplace front brake pads and discs * (Ford Galaxy )
Replace front brake pads and discs * (Ford Galaxy 2006-2015) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if you're
More informationTOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation
TOYOTA TUNDRA 2007- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-34070 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake
More informationThe H-MAC Heavy Metal Articulating Chassis Construction Guide
The H-MAC Heavy Metal Articulating Chassis Construction Guide The Heavy Metal Chassis is constructed with two identical drive modules built using 10 mechanical sub-assemblies. The drive modules are integrated
More informationPerfect Park 7000 Installation & Unloading Instructions Operating Manual
Perfect Park 7000 Installation & Unloading Instructions Operating Manual 1) Always file a claim with the truck line if the lift has been damaged! (If you don t originally notice the damage, but find some
More informationRear Parking Brake Cable (93 Cobra)
Rear Parking Brake Cable (93 Cobra) Materials in the box: Brake Cable Tools Needed: One jack and four jack stands. One socket wrench with a 12mm, 13mm ( ½ inch, 12 point DEEP WALL DO NOT FORGET THIS) and
More informationFlexJet - Flex Cable Replacement
P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationIn summary, the procedures includes removal of the belly pans, draining of the engine block, draining of the radiator, coolant mixing and refilling.
COOLANT DRAIN AND CHANGE PROCEDURE Recently, there was a request for a picture guide for draining/changing coolant (Robot808 and James-man) and since I was going to do this operation on Idaho (88), I took
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationNote: Replace the washer and the spacer above the turgo or the shaft adapter with the spacer above the washer as shown in the following pictures.
BEARINGS, SERVICE & ASSEMBLY IMPORTANT Bearing maintenance is important. You should replace bearings ONCE PER YEAR or as soon as you notice any looseness from wear. If they are too loose, severe damage
More informationHow to replace your Turbo Actuator Step by Step
How to replace your Turbo Actuator Step by Step Special thanks to other forum members who have previously dealt with this problem! Old By Chirpz New Your Turbo is a lot tougher than the electric actuator
More informationThanks for Ordering The Kawasaki KLX Adjustable Lowering Kit From
www.scootworks.com Thanks for Ordering The Kawasaki KLX Adjustable Lowering Kit From READ THIS BEFORE UNPACKING YOUR KIT! This instruction booklet contains detailed steps for installing the rear suspension
More informationRZR 900 spring/shock installation
RZR 900 spring/shock installation Thank you for purchasing the Shock Therapy Dual Rate Spring Kit for your RZR 900. Your item list: 2 Front upper coil springs, 2 Front lower coil springs, 2 Rear upper
More informationFord AOD-4R70W-AODE Cable Operated Shifter Installation Instructions
Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable
More informationVolvo 1800 Dash Pad Replacement
Volvo 1800 Dash Pad Replacement (courtesy of John Garden State Chapter Volvo Club America) Reupholstering the dash Well it has been some time since I have been online in the forum. Winter is a quite time
More informationThis is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the
This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the box and assemble it. If you have not assembled a bicycle
More informationSwitchback Carrier Rack System
Switchback Carrier Rack System Installation Instructions 1 Rocky Mountain Westy Ph. (970)310-3441 Introduction Thank you for purchasing the Rocky Mountain Westy Switchback Carrier Rack System. We pride
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationMustang Steeda Tri-Ax Shifter Installation Guide
Mustang Steeda Tri-Ax Shifter Installation Guide The below installation instructions work for the following products: Mustang Short-Throw Shifters and Mustang Handles This "all questions answered" guide
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More informationJ&M Mustang Rear Lower Control Arms (2005+) - Installation Instructions
J&M Mustang Rear Lower Control Arms (2005+) - Installation Instructions The below installation instructions work for the following products: J&M Mustang Rear Lower Control Arms (2005+) Please read through
More informationRebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL
Rebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL Disclaimer: I have benefited greatly from others who have taken the time to post auto repair videos/tutorials online. To try and return the
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationM52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit
Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure
More information4x4 actuator "Cable Froze" 1988 s S-10 Forum
Page 3 of 17 Converting a vacuum actuator to a locking cable system on a 1995 Chevy S10 Blazer 4x4 Many call this a posi-lock system. I spent a total of only $25.50 USD on this project. Other comparable
More informationWARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil.
WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. Things needed for assembly. -2 tubes of blue loc-tite. I don
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationBBK Electric Mustang Fuel Pump Kit - (86-97 V8) - Installation Instructions
BBK Electric Mustang Fuel Pump Kit - (86-97 V8) - Installation Instructions The below installation instructions work for the following products: BBK Electric Mustang Fuel Pump Kit - 190 LPH (86-97 V8)
More informationEZ-Glide Wheels Installation Patent Pending Revised 8/23/2011
EZ-Glide Wheels Installation Patent Pending Revised 8/23/2011 Questions: Lakeside Quilt Co. Jack Boersma Toll Free (888) 361-4806 www.lovetoquilt.com Cell (406) 270-4715 sales@lovetoquilt.com Toll Free
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationInstallation Instructions Borla Stinger S-Type Cat-Back Exhaust (05-09 GT)
Installation Instructions Borla Stinger S-Type Cat-Back Exhaust (05-09 GT) Overview: This installation guide will cover installation of the Borla Stinger S-Type Catback Exhaust for all Mustang GTs from
More informationFox 2.0 Adjustable Coilovers (Par# ) Installation on a 2013 F-150 (2WD)
Fox 2.0 Adjustable Coilovers (Par# 983-02-052-2) Installation on a 2013 F-150 (2WD) This guide is for the install of the Fox 2.0 adjustable leveling struts on a 2013 F-150 2WD, these are being installed
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationE46 FUEL FILTER CHANGE Pics from CI
1 of 10 5/3/2010 1:48 PM E46 FUEL FILTER CHANGE Pics from 2001 330CI Bellows Expansion Joints Metal Bellows Expansion Joints in Every Style from Flexicraft www.flexicraft.com/metal_bellows Ask a BMW Mechanic
More informationRaingear Mustang Windshield Wiper System Installation Instructions E F A
Raingear 1965-1966 Mustang Windshield Wiper System Installation Instructions J I H J G E F A D K 2 speed switch B C L Intermittent switch Please try our way first. This system is designed to fit in your
More information2017 Current Ford Raptor ADD Pro Rear Bumper Installation Instructions
2017 Current Ford Raptor ADD Pro Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We
More information1. Single-speed bicycle (SSB) lower fork legs... Page 3 2. Multi-speed bicycle (MSB) lower fork legs... Page 4
TM owner s instruction manual the ULTIMATE SURFBOARD RACK I. Messages & Warnings...Page 2 II. FORK BASE UNIT COMPONENTS...Page 2 III. SELECTING PROPER LEG TYPE...Page 2 IV. LEG LENGTH ADJUSTMENT & FORK
More informationMaximum Motorsports Camber Caster Plates (05-10):
Maximum Motorsports Camber Caster Plates (05-10): Tools Required: Lug Wrench 21mm Deep Socket 18mm Deep Socket 15mm Deep Socket 17mm Socket 13mm Socket 10mm Socket Torque Wrench (requires 166lb-ft capacity
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationEibach Pro-System-Plus
Eibach Pro-System-Plus Tools : - Floor Jack - 3 Jack Stands (4 preferred) - 2 wheel stoppers - Car wrench set - Fire torch - Bolt thread locker (use on every bolt you tight) Disclaimer: This guide is not
More informationRekluse Motor Sports. The z-start Clutch LTR 450. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.
Rekluse Motor Sports The z-start Clutch LTR 450 Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS166 LTR 450 191-266 Manual Revision: 032306 Rekluse Motor Sports, inc. 110
More informationWritten By: David Hodson
2008-Present Scion xb Oil Change Second generation Scion xb oil change. Written By: David Hodson ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Change the oil in your 2008 or newer Scion xb
More informationJaguar Update. Adjustable Reaction Plate
Jaguar Update Adjustable Reaction Plate Home January 7, 2008 I recently installed an adjustable reaction plate from CoolCat Express Corp. I've included some notes from that experience. I'm not affiliated
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More informationSUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm. Acrobat Printable Version
SUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm Introduction Acrobat Printable Version I'd like to thank Ben Davis for providing the pictures for this procedure. Ben took the time to take
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationComfort Tri-Rider Assembly Guide
1. Carefully remove all the components and packaged hardware from the shipping boxes. 2. Remove all protective materials from the fork, front frame and rear frame sections. 3. Read this assembly manual
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationRekluse Motor Sports. The e-axle KTM. Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.
Rekluse Motor Sports The e-axle 2003 2007 KTM Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.000 RMS 2733 195-2733C Manual Revision: 032207 Rekluse Motor Sports, Inc. 110 E. 43
More information2013 RT / 2014RT / 2015 RT - Shock Spring Adjuster Installation Instructions
2013 RT / 2014RT / 2015 RT - Shock Spring Adjuster Installation Instructions Billet Aluminum Adjusters (2) Shock Spring Compressors (Optional) Spanner Wrench (1) BajaRon Decals Not Shown (4) Adjuster Scuff
More informationwhat you need to do is hit the taper housing as hard as you can with your hammers AT THE SAME TIME and at a slight angle, what will happen is you
first things first, get the car on axle stands and the wheels off. Open the bonnet to let more light through to the area in which you'll be working. The following guide shows the passenger side being done
More informationRetrofit Steering Column
Retrofit Steering Column INSTALLATION INSTRUCTIONS for 1965 Ford Falcon FOR PART NUMBER S: 1170906010, 1170906020, 1170906051, 1130906010, 1130906020, 1130906051 S INCE 1986 www.ididitinc.com 610 S. Maumee
More informationSteeda Lower Control Arms ( )
Steeda Lower Control Arms (2005-2012) NOTE: The following installation was performed on a 2007 Mustang GT/California Special. The control arms were previously sold in a blue color, but now they are sold
More information20 Rigid Industries LED Light Bar Installation into a 2002 Ford Super Duty
20 Rigid Industries LED Light Bar Installation into a 2002 Ford Super Duty This write-up is how I installed the Rigid Industries 20" E-Series LED Light Bar into the grill area behind the license plate
More informationupper and lower ball joints ( I went with Moog from rockauto.com): two K80026 and two K8607T
Parts required: two 5C3Z*4A322*AA = hub / steering knuckle o-ring two AC3Z*1S175*A = updated axle shaft "dust seal" two 5C3Z*3254*A = steering knuckle / axle shaft seal upper and lower ball joints ( I
More informationType 2 Push-Through 37 Ton Log Splitter. Assembly Manual
Type 2 Push-Through 37 Ton Log Splitter Assembly Manual Refer to this manual for the following models: RS37PT-LF09PC-16-1 RS37PT-LF09EC-16-1 RS37PT-LF09EC-16-2 RS37PT-LF13EC-22-1 RS37PT-LF13EC-22-2 RS37PT-LF15EC-22-1
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT Thank you for choosing the Motor Trike GL1500 Rake Kit. We ask that you read the directions before you start and follow them very closely.
More informationWHEN TO GREASE WARNING: NOTE:
The Bearing Lube system provides an easy way to fill axle hubs and repack bearings with grease to ensure proper bearing lubrication. To locate the grease (zerc) fitting, simply remove the rubber plug in
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationEnclosure Drawer #8 (2) Mounting Brackets. # / (L&R) Front Mounting Brackets # / (L&R) Rear Mounting Brackets
INSTALLATION INSTRUCTIONS Part # 188 Ford Escape Hybrid Rear Cargo Drawer Mounting Kit (This kit is designed to mount on the rear cargo drawer sold separately) Please read and fill out the enclosed warranty
More information2007 Current Jeep Wrangler JK Stealth Fighter Rear Bumper With Tire Gate Installation Instructions
2007 Current Jeep Wrangler JK Stealth Fighter Rear Bumper With Tire Gate Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set
More informationReplacing MK4 Golf/Jetta radiator mounts in-car
Replacing MK4 Golf/Jetta radiator mounts in-car This is a guide to replacing the radiator mounts in a MK4 Golf/Jetta. This involves moving the core support to the service position which allows you to do
More informationBrake Caliper Rebuild - Part Numbers & Tips Per Jim Millet, 3/15/2005
Per Jim Millet, 3/15/2005 Not too difficult a job. Rears are easier than fronts to access. You ll need the following gasket sets: Front caliper gasket set, P/N 34 11 1 157 037, MSRP $13.58 Rear caliper
More informationJL SHIELD TIRE CARRIER INSTALLATION INSTRUCTIONS
JL SHIELD TIRE CARRIER INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/4 Wrench 3/4 Socket 9/16 Wrench or Socket 1 1/2 Socket 1 1/8 Wrench 13mm Socket Torque Wrench for 1 1/2 Socket HARDWARE 2-1/2 X 2 Hex Bolt
More informationHPFP DIY. Warning: The injector fuel lines, the rail, and the HPFP are pressurized long after you turn off the car, I recommend
HPFP DIY Warning: The injector fuel lines, the rail, and the HPFP are pressurized long after you turn off the car, I recommend disconnecting the battery and letting the car sit over night before performing
More information2800 VIBRO-TILL FIELD CULTIVATOR ASSEMBLY INSTRUCTIONS Series. Kongskilde
2800 VIBRO-TILL FIELD CULTIVATOR Kongskilde 2800 Series *Model may not be exactly as shown. Kongskilde reserves the right to make changes to product designs and specifications without notice or obligation
More informationConverting a Series Land Rover to front wheel disc brakes using the kit made by Torrel Industries Ltd,
Converting a Series Land Rover to front wheel disc brakes using the kit made by Torrel Industries Ltd, Torrel Industries ltd Series Land Rover front brake conversion kit: Difficulty - Low Except for one
More information2014 Current Chevy/GMC 1500 HoneyBadger Rear Bumper Installation Instructions
2014 Current Chevy/GMC 1500 HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationC3 Syncro Drive Proclimb 1100 Installation Instructions
Revision 4 Nov 8-2013 201A Old Town Road, Sicamous, BC. V0E 2V4 Ph 250-833 3538 Fax 888-716 5903 www.c3powersports.com Thank you for purchasing a ProClimb M, ProCross F & XF SyncroDrive Note: This modification
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationHub Stands -- VERSION 5.0
Hub Stands -- VERSION 5.0 Thanks for choosing our Alignment Hub Stands for your chassis setup needs. We hope you'll find them as handy, accurate, and easy to use as we do! Each stand has a max capacity
More informationAmTryke Adult Recumbent Model HP1000 #50-HC-1000
AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More information