Honeycomb Shades Skylight

Transcription

1 STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Skylight Motivia Motorization

2 Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at or visit for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be a painless as possible. Table of Contents Step 1 - Getting Started....3 Overview - Motorization Honeycomb Skylight....4 Step 2 - Brackets & Battery Pack Placement....5 Step 3 - Installing the Brackets....6 Step 4 - Installing the Battery Pack....7 Step 5 - Installing the Top Rail....8 Step 6 - Installing the Bottom Rail...9 Step 7 - Installing the Tracks Step 8 - Operating the Shade Step 9 - Adjusting the Limits Step 10 - Leveling the Shade Troubleshooting Removing the Shade Managing the Wires Advanced Programming Care & Cleaning Customer Service Hours Monday Friday: 6am 7pm PT Saturday Sunday: 7am 4pm PT Safety Warranty...Back Cover smithandnoble.com 1 smithandnoble.com

3 Step 1 Parts & Tools Overview Getting Started Motorized Honeycomb Skylight First, make sure you have all the parts and tools required to install your shades. ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16 drill bit. Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. Additional fasteners other than those sent with your shade may be required. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. SCREWS MOUNTING BRACKETS BATTERY WAND CLIPS WALL MOUNT BATTERY PACK CLIPS PENCIL (NOT INCLUDED) LEVEL (NOT INCLUDED) PENCIL & SCREWDRIVER (NOT INCLUDED) POWER DRILL & LEVEL (NOT INCLUDED) 3 smithandnoble.com

4 Step 2 Brackets & Battery Pack Placement Step 3 Installing the Brackets Determine Placement of Brackets and Battery Pack Make sure that the battery wire will be able to reach the motor. 3" Shades are shipped with the required number of brackets for proper installation. End brackets should be located approximately 3" from either end. There is a minimum of 2 3 4" needed from the back of the bracket to the front of the window opening. MIN. OF FROM BACK OF BRACKET TO FRONT OF WINDOW OPENING MOUNTING BRACKETS BATTERY PACK MOUNTING BRACKETS Depending on the width of the shade, additional brackets may be necessary, evenly spaced between the two end brackets. Using the mounting bracket as a template, measure to the edge of the bracket and mark the hole locations with a pencil for drilling. When mounting brackets, make sure they are in line with each other. 5 smithandnoble.com

5 Step 4 Installing Battery Pack Step 5 Installing the Top Rail Battery Pack - Attach the battery pack BATTERY PACK CLIPS Start with the top rail/fabric assembly. clips in the desired location, with the The top rail is the rail with the motor in screws provided. it. Before mounting the headrail, make Press the battery pack into the clips. Note: Be sure that the battery wire will reach the motor plug at the position that you are installing it. A sure that the receiver wire is out of the headrail. For optimal performance position the receiver wire so that it is facing into the room. Position the motor wire so that it comes out the back side of the shade. BATTERY PACK Be sure the motor wire is not pinched by the bracket. Position the rail with the front lip (A) resting on the hooks of all the brackets. Push the rail firmly up and toward the window until the groove on the rail snaps into place, (B) as shown. Attaching the Power Source BATTERY PACK BATTERY WIRE B Plug the battery wand wire in the motor wire MOTOR WIRE 7 smithandnoble.com

6 Step 6 Installing the Bottom Rail Step 7 Installing the Tracks Select the desired channel with the "Channel" key. The channel indicator light will illuminate the channel that is on. If all 5 lights are lit, the remote will control all 5 channels at once. UP STOP CHANNEL INDICATOR LIGHTS Place the track against the front of the top and bottom rails. Attach the track with the screws provided. Space the screws no more than 12" apart. Press the "Down" key to lower the shade. DOWN CHANNEL CHANNEL + FRONT OF TRACK OVERLAPS FRONT OF RAILS Follow the same procedure for the other track. Make sure that the 2 tracks are parallel to each other. B 4" A ATTACHMENT SCREWS Position the rail with the front lip (A) resting on the hooks of all the brackets. Push the rail firmly down and toward the window until the groove on the rail snaps into place, (B) as shown. 12" 12" 12" 9 smithandnoble.com

7 Step 8 Operating the Shade Step 9 Adjusting the Limits Set the Limits on Primary Remote 1. Select the desired channel with the "Channel" key. The channel indicator light will illuminate the channel that is on. If all 5 lights are lit, the remote will control all 5 channels at once Channel Indicator Lights Up The lower and upper limits have been set at the factory. If you need to make adjustments to the limits, follow the instructions on page Tapping the "Up" or "Down" keys for less than 2 seconds will move the shade in short steps. Holding the "Up" or "Down" keys down for more than 2 seconds before releasing, will operate the shade in the faster standard speed. Stop Down Channel + Channel C L Limit Confirm Use the "channel" key to select the channel for the shade that needs to be adjusted. Then follow the directions on page 9. If only adjusting one shade on a channel, unplug the other shades. 3. Press the "Up" or "Down" keys to raise or lower the shade. BACK OF REMOTE 4. Press the "Stop" key to stop the shade anywhere along the travel. 11 smithandnoble.com

8 Step 9 Adjusting the Limits Step 9 Adjusting the Limits Setting the Lower Limits Setting the Upper Limits OPERATION RESULT 1 Hold "limit" key for 6 seconds The motor begins to jog OPERATION RESULT 1 Press "Up" key on the remote transmitter The motor will go up continuously 2 Release the key after 2 jogs The motor is ready for limit setting 2 When the motor is close to the endpoint of the upper limit, press "Stop" key on remote The motor stops running 3 Press "Down" key The motor will go down continuously 3 Press either the "Up" or "Down" key The motor runs step by step to adjust upper limit accurately. 4 When the motor is close to the endpoint of the lower limit, press "Stop" key on the remote. The motor stops running 4 Confirm the setting by pressing the "Confirm" key on the remote The motor jogs and the setting is completed. 5 Press either the "Up" or "Down" key The motor runs step by step to adjust lower limit accurately. 6 Confirm the setting by pressing the "Confirm" key on the remote. The motor jogs and the setting is completed. 13 smithandnoble.com

9 Step 10 Leveling the Shade Troubleshooting ADJUSTMENT SCREWS If the rail is uneven at the top, raise the low side with the outer adjustment screw. Level the Moving Rail Motorized Skylight Shades use a system that allows easy leveling of the moving rail. It is designed to make slight adjustments (Less than 1") to level the moving rails of your shade. It is not designed to make length adjustments. Use a flat head screwdriver or a coin (a quarter works the best) to turn the adjustment screw to raise or lower that side of the bottom rail. The adjustment screw is on the top of the moving rail. One quarter turn of the screw will move the moving rail up or down approximately 1 4". Over-turning the adjustment screw (more than 1" of adjustment) can cause the cord to tangle or wedge inside the rail. The screw should turn easily - Do Not Force. PROBLEM SOLUTION 1 The motor does not work and the shade is stuck in the closed position Carefully pull down on the moving rail enough to allow access. Follow solution below. If this required, limits will need to be reset. See Setting Limits on Pg The motor does not work 1. Check that the power source and motor are connected properly. 2. If using a battery pack - confirm that the batteries are fresh. 3 The motor continues to run in one direction 4 The motor stops working or works intermittently 5 The indicator light on the remote does not shine or the remotecontrolling range becomes shorter. The limit setting was unsuccessful and needs to be reset. If using a battery pack, replace the batteries in the pack with 8 fresh AA alkaline batteries. Replace the battery in the remote (CR2032 Lithium) ADJUSTMENT SCREWS If the stack is uneven at the bottom, lower the high side with the inner adjustment screw. ADJUSTMENT SCREWS 15 smithandnoble.com

10 Removing the Shade Optional To remove a shade, insert a flat blade screwdriver between the rail and the bottom back of the bracket (tab which extends out slightly from each bracket). Managing Wires Use the included cable ties to bundle any excess wires. Gently pry the screwdriver to release the bracket from the headrail. Take care not to damage the painted finish of the headrail. As you release the brackets, support the headrail to keep it from falling. Insert screwdriver and gently pry 17 smithandnoble.com

11 Advanced Programming Advanced Programming Replace Original Remote or Add Additional Remote Remove/Link a Shade from One Remote/Channel to Another 1. Remove the shade from the window (if needed). Press the "Setting" key on the motor until the shade jogs once. Release A. Unlink the motor from the remote Note: This step also erases the lower and upper limits. the button immediately after the first jog - this should be no more than 3 seconds. 2. Repeat the following steps for all shades that will be controlled by a single channel. 3. Select the channel that you want to program using the "Channel" selector key. Settings button (Black) Remove from window (when needed), to access the settings button. 1. Remove the shade from the window. Press and hold the "Setting" key for 8 seconds. The motor will make a series of jogs. 2. Release the "Settings" key. The original remote or channels have been unlinked. 4. Press and hold the "Confirm" key until the shade(s) jog once Channel Display B. Link the motor to the new remote or channel. 5. Repeat steps 1-4 to program the rest of the channels on a multi-channel remote. Up 1. Follow the steps for replacing the remote to the left. 6. To set the ALL function on the multichannel remote, activate the setting keys (step 1) on all shades. Scroll through the channels until all the indicator lights are lit. Stop Down Channel + Channel C L Limit Confirm 2. Set the lower and upper limits by following the instructions on Pg. 12. Please note: You will not be able to adjust the lower or upper limits with the secondary remote. If the original remote was lost and the limits need to be reset, follow the instructions in the next section. 19 smithandnoble.com

12 Care & Cleaning Safety Care & Cleaning Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all that is required to keep your blinds looking fresh and neat. Most stains can be blotted with a damp sponge and mild detergent. Before using anything stronger than mild detergent and lukewarm water, test an unobtrusive corner of the shade. If you have any questions, call us at , we would be glad to help. Safety First. Style Second To None. Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tie-down devices and built-in cord stops. To protect young children and pets, there s no better way to eliminate risk than to use one of our cordless products. Child Safety 21 smithandnoble.com

13 Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at and we ll arrange for a repair or replacement ASAP. SN_LL_SM_2017_ Smith & Noble Home, Inc. All Rights Reserved SN 2042