St. Clair County Road Commission. For 66,000 GVW Plow Truck Page 1 of 27 Item Descriptions Compliance

Transcription

1 Page 1 of 27 NOTICE IS HEREBY GIVEN THAT SEALED PROPOSALS ARE SOUGHT AND REQUESTED FOR THE FOLLOWING: BID NAME: BID OPENING: THREE (3) WESTERN STAR TANDEM-AXLE PLOW TRUCKS WITH WING JUNE 10, :00 PM. LOCAL PREVAILING TIME. CONTACT PERSON: PLACE OF OPENING: Deborah Martin Administrative Assistant for Operations St. Clair County Road Commission 21 Airport Drive St. Clair, MI PHONE: Vendors must submit their Bid in a sealed envelope. Please print the following on the face of the envelope - Name and address of the bidder - Bid Name THREE (3) WESTERN STAR TANDEM-AXLE PLOW TRUCKS WITH WING PROVISIONS 1. You are urged to mail your bid in early. Late bids will not be accepted and will be returned unopened to the vendor 2. Proposals must be submitted on the forms provided by the St. Clair County Road Commission. Forms are to be filled out in their entirety. When a bid does not meet specification, a reason for the deviation must be given. 3. The submission of this bid certifies that the bidder has read, is familiar with, and will comply with any and all segments of these specifications as described below. 4. Bids that do not have all the applicable lines filled in on the bid sheet may be disqualified as a non-responsive bid. We will not assume that the product meets specification when lines are left blank. If it is necessary to bid alternate equipment or to take exceptions to the specifications as set forth, this must be so stated in your bid. For each item, please place an X in the appropriate box (Yes No ) to signify whether or not you are in complete compliance with the specification. Failure to follow the format or answer the specification may cause your bid to be disqualified. If you need extra space to describe your product, please feel free to attach extra sheets. When doing this, be sure your description references the appropriate question number. Any exceptions to the specifications, lines marked No, must be fully explained in the comment section and will only be considered if advantageous to the St. Clair County Road Commission 5. The bidder must submit with their bid, detailed specifications and necessary information (product literature) on the item(s) bid. 6. The bid will be awarded to the vendor that supplies the bid items that is in the best interest of the St. Clair County Road Commission

2 Page 2 of The Board of County Road Commissioners of St. Clair County reserves the right to reject any or all bids, waive any irregularities, or to make the award in part or its entirety. 8. This equipment is to be delivered FOB to St. Clair County Road Commission, 21 Airport Drive, St. Clair, MI Regulations 1. All products must meet all applicable Local, State, and Federal regulations.... Yes No 10. Warranty Standard limited warranty will be required of the manufacturer of the products that shall be: 1. All items shall be guaranteed for a minimum period of one (1) year against defective parts and workmanship... Yes No 2. All defective parts and labor are the obligation of the vendor during this period... Yes No 3. Copy of warranty should accompany bid documents... Yes No If defects occur during this time, the defective product shall be replaced or corrected by the contractor without cost to the County except where it shall be clearly shown that the defect is due to misuse and not to faulty manufacture or installation. 11. Guarantee 1. The bidder guarantees that the item(s) offered is standard new product... Yes No 12. Fair employment practices The Contractor agrees that he will not discriminate against any employee or applicant for employment, to be employed in the performance of this Contract with respect to his hire, tenure, terms, conditions or privileges of employment or any matter directly or indirectly related to employment because of his age, except when based on a bona fide occupation qualification or because of his race, color, religion, national origin or ancestry (Act No. 251 P.A. 1955, as amended). 13. Payment Before payment of the final estimate or payment of any retainage, the Road Commission will ascertain that the work has been performed in accordance with the plans and specifications or with such modifications thereof as may have been approved. Payment cannot be processed by the Road Commission until all contract items have been delivered in satisfactory condition with an invoice referring to the Purchase Order Number and mailed to / billed to the address indicated on the Purchase Order. If agreed specifications are not met, the St. Clair County Road Commission reserves the right to hold payment until concerns are addressed and final agreement is settled. 14. Notice The ST. CLAIR COUNTY ROAD COMMISSION in accordance with Title VI of the Civil Rights Acts of 1964, , 42 U.S.C. 2000d-222d-4, the Civil Rights Act of 1987, P.L , and Title 49, Code of Federal Regulations, Department of Transportation, subtitle A, Office of the Secretary, Part 21, Nondiscrimination in federally assisted programs of the Department of Transportation issued pursuant to such Act, hereby notifies all bidders that it will affirmatively insure that in any contract entered into pursuant to this advertisement, Disadvantaged Business Enterprise firms will be afforded full opportunity to submit bids in response to this invitation and will not be discriminated against on the grounds of Race, Color Sex, Age, National Origin, or Handicap in consideration for an award.

3 Page 3 of 27 SECTION I - GENERAL SPECIFICATIONS FOR THREE (3) 66,000 GVW TANDEM-AXLE PLOW TRUCK 1. GENERAL SPECIFICATIONS: It is intended that this unit be used as a highway maintenance truck, equipped with an underbody blade, front mounted snowplow, right hand and/or left hand wing and a dump body with a minimum capacity of 11 cubic yards. The battery box, toolbox, air tanks and any other items attached to the truck chassis are required to maintain a 24-inch ground clearance. BIDDER SHALL PROVIDE ALL CHASSIS DIMENSIONS WITH BID PROPOSAL 1. Chassis / Cab shall be configured for front plow, wing plow, under belly plow / end dump body... Yes No 2. Ground clearance shall be 24 inches on any attachments, air tanks, battery box, etc.... Yes No 3. Truck shall have Calc. Start / Grade Ability: 30.20% / 55 MPH... Yes No 4. Chassis configuration shall be 6x4.... Yes No 5. Truck shall be 66,000 Gross Vehicle Weight Rating... Yes No 6. Cab configuration shall be Standard cab with minimum 130 inch BBC... Yes No 7. CT measurement shall be 138 inches... Yes No 8. Truck frame length BOC to be 196 inches... Yes No 9. Equipment width to be 102 inches... Yes No 10. Gear Ratio shall be Yes No 11. Engine torque to be maximized at RPM... Yes No 12. WARRANTIES: Refer to Section Yes No 2. FRAME 1. Frame shall have single rails rated for 120,000-PSI minimum... Yes No 2. Frame shall be minimum 2,500,000 RBM rating... Yes No inch integral (Not bolted) front frame extension shall be provided with.250-inch insert and shall be designed for attaching a front plow assembly that weighs approximately 4,000 lbs... Yes No 4. Frame rail shall overhang to accommodate body equipment... Yes No 5. Heavy Duty Front AND rear tow hooks shall be provided, (rear hooks to be shipped loose)... Yes No 3. ENGINE 1. Engine shall meet all current EPA / CARB Emission certifications with SCR Technology... Yes No 2. Engine must provide minimum 430 HP (13 liter)... Yes No Note: Both Factory and Engine manufacturers Dyno-sheets to be provided 3. Engine must provide minimum 1650 Lb/Ft torque... Yes No 4. Maximum Engine RPM to be 2, Yes No 5. Engine shall be equipped with dual element, high capacity air filters.... Yes No 6. Air filter to be setup with inside / outside air intake... Yes No 7. Engine must be equipped with Extended Life Coolant capable of 40 degrees F... Yes No

4 Page 4 of Effects for front LIVE PTO must be provided with 1350 adapter flange.... Yes No 9. Engine shall have Horton Drivemaster, two-speed, air-tethered, on / off fan drive... Yes No 10. ENGINE SHALL BE EQUIPPED WITH A FUEL PRIMER... Yes No 11. Engine shall utilize Gates Bluestripe coolant hoses with constant tension clamps... Yes No 12. Engine oil pan to be powder-coated for added protection... Yes No 13. Air Compressor shall have 15.9 CFM with 130-psi governor... Yes No 14. Detroit Diesel Virtual Technician with Five Year Contract... Yes No 4. EXHAUST SYSTEM 1. Exhaust shall be stationary, single vertical, exit on extreme outboard R/H side... Yes No 2. Exhaust system shall maintain 24 ground clearance... Yes No 3. Exhaust system shall maintain 3 clearance from cab, frame... Yes No 5. TRANSMISSION 1. Transmission shall be VHP 13 speed Eaton UltraShift PLUS Automated Transmission.... Yes No 2. Transmission shall be programmed for snow plow use... Yes No 3. Transmission to be setup with auxiliary speed sensor port for dedicated Ground-Speed... Yes No 4. Transmission 5 year warranty to be included in cost of the bid... Yes No 6. BRAKES (GENERAL) 1. Brake system to be ABS design... Yes No 2. Air tanks to be mounted inside frame rails... Yes No 3. Brake system shall utilize BW AD-IP air dryer with heater.... Yes No 4. Brake Air system shall utilize BW DV-2 Automatic drain with heater... Yes No 5. Brakes shall have non-asbestos linings... Yes No 6. Brake drums shall be cast iron design... Yes No 7. Haldex automatic slack adjusters shall be provided.... Yes No

5 Page 5 of FRONT BRAKES 1. Brake shoe size shall be minimum of 16.5 X 6... Yes No 2. Brake system shall utilize Long Stroke front brake chambers... Yes No 8. REAR BRAKES 1. Brake shoe size shall be minimum of 16.5 X 7... Yes No 2. Brake system shall utilize Long Stroke axle spring parking brake chambers... Yes No 3. Brake system shall have cam brake auxiliary support brackets... Yes No 4. Brakes shall be forward and high mounted on rearmost axle with auxiliary support brackets... Yes No 9. FRONT AXLES AND SUSPENSION 1. Front axles shall be 20,000 lbs capacity... Yes No 2. Front suspension shall be 23,000 lb. Taper-leaf design... Yes No 3. Axle to be Meritor MFS A... Yes No 4. Front oil seals shall be of the wet design... Yes No 10. REAR AXLES 1. Axle suspension shall be tandem axles with 46,000 lbs capacity.... Yes No 2. Axles to be Meritor RT P... Yes No 3. Driver s controlled differential lock traction system with four wheel lock capability... Yes No 4. There shall be in-cab, air operated switches for power divider and cross axle lock functions... Yes No 5. Airliner rear 46,000#... Yes No 6. Airliner high position ride height... Yes No inch axle spacing... Yes No 8. Dual air rear suspension leveling valves... Yes No 9. Transverse control rods... Yes No 10. Rear shock absorbers two axles (tandem)... Yes No 11. Main driveline to be 1810 HD Dana Spicer with half round yokes... Yes No 12. Intermediate driveline to be 1710 Dana Spicer with full round yokes... Yes No 13. Rear oil seals shall be of the wet design... Yes No 14. Rear axle housings to utilize 75W-90W synthetic lubricant and be labeled as such... Yes No 15. There shall be internal lube pump and spin on filter for front differential... Yes No

6 Page 6 of WHEELS AND TIRES 1. Front wheels shall be 22.5 X 12.25, 10 hub pilot, 5-hand steel disc type... Yes No 2. Rear wheels shall be 22.5 X 8.25, 10 hub pilot, 2-hand steel disc type.... Yes No 3. Front tires shall be Michelin XZU-S R ply... Yes No 4. Rear tires shall be Michelin XDE M/S 11R ply... Yes No 5. Front and rear brake dust shields to be installed... Yes No 6. Nylon wheel guards shall be provided... Yes No 7. Wheels shall be Powder-coated White... Yes No 12. FRONT END 1. Fenders / Hood shall tilt forward as one piece... Yes No 2. Painted stationary grille trimmed to clear Husting 34 front plow hitch... Yes No 3. Inside / Outside air intake system.... Yes No 4. Side air intake with engine compartment inlet for warm air blend... Yes No 5. Fenders shall be equipped with 2 wide extensions to cover tire width... Yes No 6. Bug screen to be installed behind the grill... Yes No 7. Omit front bumper... Yes No 13. CAB EXTERIOR 1. Cab configuration shall be Standard cab with minimum 130 inch BBC... Yes. No 2. Cab to be insulated with deluxe sound suppression cab insulation... Yes No 3. Windshield, rear window, door glass, and wing windows to be tinted glass... Yes No 4. Mirror heads and C-loop shall be stainless steel... Yes No 5. Heated, motorized mirrors shall be provided... Yes No 6. LH / RH 8-inch convex shall be mounted under primary mirrors... Yes No 7. Right hand down-view mirror shall be provided... Yes No 8. Cab steps shall be powder coated and offset with non-slip grip surface.... Yes No 9. Cab exterior grab handles shall be provided for both RH and LH doors... Yes No 10. Air horn to be single-trumpet, mounted under the hood with snow cover... Yes No 11. Single electric horn to be provided... Yes No 14. ELECTRICAL SYSTEM 1. Battery system shall provide minimum 3,000 (CCA) cold cranking amps... Yes No 2. Batteries shall be mounted in the cab... Yes No 3. Batteries jump-start studs shall be provided at the battery box... Yes No

7 Page 7 of Batteries shall have factory installed disconnect switch provided at the driver s seat area... Yes No 5. Alternator shall be a 145 amp alternator... Yes No 6. Electrical system shall utilize Manual Reset Circuit Breakers.... Yes No 7. Ten factory-installed, 20 amp, dash switches with chassis mounted electrical connectors for body integration, use TBD... Yes No 8. Plow light wiring harness shall be provided (8THJ).... Yes No 9. Taillight wiring harness to be provided.... Yes No 10. Factory installed, SAE J560 trailer wiring harness shall be provided.... Yes No 11. Headlights shall be halogen daytime running light system (DTRL).... Yes No 12. Taillights and backup lights shall be 4 round LED style lights.... Yes No 13. Front marker lights shall be provided and be LED style lights.... Yes No 14. High visibility fender mounted turn signals must be provided... Yes No 15. Small, aerodynamic, LED clearance marker lights shall be utilized.... Yes No 16. Back up alarm with 102 dba shall be activated whenever the vehicle is in reverse gear.... Yes No 17. Provide harness and electric brake controller... Yes No 18. Body builder water-tight junction box containing all lighting hookups for the rear of the truck shall be provided... Yes No 19. Truck to have pre-trip exterior light check feature... Yes No 20. Wiring system shall not be a multiplex system... Yes No 15. CAB INTERIOR 1. Interior trim to be Grey Vinyl with PDM floor mat and factory floor-mats provided... Yes No 2. Driver and passenger's seats shall be high back with integral headrests... Yes No 3. Driver's seat shall be air ride support with adjustable lumbar support and armrests on both sides... Yes No 4. Dash mounted 12V auxiliary outlet to be provided... Yes No 5. Air conditioning system shall be provided... Yes No 6. Cab shall have heater / defroster (including side windows) with main HVAC switch... Yes No 7. Radio with AM/FM/WB with bluetooth, 2 cab speakers shall be provided.... Yes No 8. Wiring harness for two-way radio to be installed (8REA)... Yes No 9. Fresh air filter for cab shall be provided.... Yes No 10. Power windows shall be provided... Yes No 11. Steering wheel to be tilt column... Yes No 12. Safety kit to include: 5 lb Fire Extinguisher, Triangles, flare kit - shipped loose, not mounted... Yes No 13. Orange seat belts shall be provided... Yes No 16. INSTRUMENTATION / DASH 1. Gauge warning systems shall include: Low coolant level... Yes No Body Raise Light/Beeper (60AJK)... Yes No 2. Gauges provided in gauge cluster shall include:

8 Page 8 of 27 Water Temperature.... Yes No Oil Pressure.... Yes No Tachometer.... Yes No Speedometer.... Yes No Fuel Level.... Yes No Voltage.... Yes No Air restriction gauge for air cleaner.... Yes No Air pressure gauges (Air 1 Air 2).... Yes No 3. Low windshield washer fluid indicator shall be provided.... Yes No 17. TRAILER CONNECTIONS 1. Air connections to end of frame with glad hands for truck... Yes No 2. Wiring to electrical connection end of frame... Yes No 3. Trailer hand control brake valve... Yes No 4. BW tractor protection valve... Yes No 5. 2 valve parking brake system with warning indicator... Yes No 18. PAINT 1. Body to be painted Dupont Imron N0 662HN (Schoolbus Yellow) Premium paint with urethane clearcoat finish... Yes No 19. WARRANTIES 1. Truck shall come with a Category II On-highway minimum 1 year unlimited warranty... Yes No 2. Warranty to include extended / roadside service warranty for 1 year unlimited, $500 per incident... Yes No 3. Engine Warranty period shall be five (5) years or 200,000 miles with Zero ($0.00) Deductible... Yes No 4. Transmission warranty shall be five (5) years or 200,000 miles... Yes No 5. Differential Warranty shall be minimum three (3) years, 300,000 miles... Yes No 6. Body rust through Warranty shall be five (5) years, 500,000 miles... Yes No 7. Frame rail warranty provided shall be five (5) years or 500,000 miles... Yes No 8. Bidder shall include detailed warranty information with the bid proposal... Yes No 9. All warranties shall begin on the St. Clair County Road Commission In-Service Date of the truck... Yes No 10. Winning bidder will supply pickup and delivery service for all warranty issues... Yes No Category II On-highway Truck warranty period. Standard year(s) Extended warranty years Cost $ Extended / roadside service warranty. Standard year(s) Extended warranty years Cost $ Engine Warranty period. Standard year(s) Extended warranty years Cost $ Transmission warranty period.. Standard year(s) Extended warranty years Cost $ Differential Warranty period.. Standard year(s) Extended warranty years Cost $ Body rust through Warranty period.. Standard year(s) Extended warranty years Cost $

9 Page 9 of 27 Frame rail warranty period. Standard year(s) Extended warranty years Cost $ Air Compressor... Standard year(s) Extended warranty years Cost $ Other Standard year(s) Extended warranty years Cost $ 20. MISCELLANEOUS 1. One Complete set of ALL required filters; spare belts shall be delivered PER UNIT.... Yes No 2. Dealer to provide detailed factory build sheet (BOM) PER UNIT... Yes No 3. Manuals 2 Parts books, 1 Service Manual, 1 Operator Manual PER UNIT... Yes No 4. Included in the above described manuals shall be Engine, Chassis, Transmission, Differentials, Electrical... Yes No 5. Diagnostic interface connector to be 6-pin, SAE J1587/1708 located below dash... Yes No 6. Engine diagnostic, transmission diagnostic, operator training shall be provided at the SCCRC Facility... Yes No 7. All Diagnostic Software and ISIS for Engine and Truck... Yes No

10 Page 10 of 27 SECTION II - BODY INTEGRATION - GENERAL SPECIFICATIONS FOR 66,000 GVW SYSTEM This specification shall describe conventional dump body with a cross-memberless understructure. Bidders must submit with their bid literature and complete specifications on the unit they propose to furnish. The body and hoist must be part of a standard product line, as described in published company literature. This is to ensure engineering integrity and parts availability. 1. BOX DIMENSIONS (CONVENTIONAL DUMP BOX) 1. Capacity to be cu yards... Yes No 2. Inside length of 14 feet... Yes No 3. Inside body width to be 84 inches... Yes No 4. Side height of 34 inches... Yes No 5. Tailgate height of 42 inches... Yes No 6. Headsheet height of 42 inches... Yes No 7. MAXIMUM EQUIPMENT HEIGHT INCLUDING LIGHTING NOT TO EXCEED 132 INCHES.... Yes No 2. SIDES & HEADSHEET ALL WELDING IS TO BE CONTINUOUS, FOR STRENGTH AND CORROSION RESISTANCE. SKIP WELDING IS NOT ACCEPTABLE. THIS INCLUDES THE MOUNTING OF THE HEADSHEET TO THE BODY. ALL ATTACHMENTS THAT ARE WELDED TO THE BOX MUST BE WELDED WITH STAINLESS WIRE, WELD SPATTER REMOVED 1. All hardware above the floor with exception of tailgate hardware shall be 201 or 304 stainless steel... Yes No 2. Sides & Headsheet to be 201 or 304 stainless steel... Yes No 3. Floor to side radius to be 6 radius... Yes No 4. Boxed top rail with a reverse bend... Yes No 5. 3 wide sideboard pockets, front and rear with intermediate brace, approximately 6 tall, 201 or 304 stainless steel... Yes No 6. Front/rear full depth corner pillars; front 8 ½ wide with 4 radius; rear 18 wide, both sloped to shed dirt, 201 or 304 SS... Yes No 7. Cab Shield to be minimum 22 inch x 84 inch, 3/ or 304 stainless steel construction... Yes No 8. Horizontal portion shall have a minimum 5 degree slope... Yes No 9. Sideboards to be 3 inch wide oak plank, painted black... Yes No 10. At the rear of the dump body, over the tires, shall be a fold-down ladder... Yes No 11. Inside the rear of the body shall be grip-strut steps spaced at 1/3 and 2/3 up from the floor... Yes No 3. FLOOR 1. Floor shall be one-piece, minimum 1/4 inch, 304 stainless steel... Yes No fabricated trapezoidal longitudinal to have1/4 A1011 inner wall, 7 ga. A1011 outer wall... Yes No 3. Floor shall be a fabricated cross-member less design... Yes No

11 Page 11 of TAILGATE: ALL welding is to be continuous, for strength and corrosion resistance. Skip welding is not acceptable. 1. Material shall be 201 or 304 stainless steel... Yes No 2. Material thickness shall be minimum 7 gauge tailgate sheet... Yes No 3. Nine panel double acting tailgate... Yes No 4. Top brace shall be inverted V, all horizontal braces shall be sloped to shed dirt... Yes No 5. 1 ½ thick 201 or 304 stainless steel upper hinge... Yes No 6. 1 ¼ diameter 201 or 304 stainless steel upper and lower tailgate pins... Yes No 7. Four 3/8 thick 201 or 304 stainless steel chain slot brackets... Yes No 8. Double ear lower tailgate latch sockets 201 or 304 stainless steel... Yes No 9. Rear pillar cap assembly 3/8 thick 201 or 304 stainless steel... Yes No 10. Tailgate lift loop 201 or 304 stainless steel... Yes No 11. 3/8 Hi Test galvanized chain sufficient length to allow tailgate to lay flat... Yes No 12. All tailgate linkage including upper pins shall have grease-able zerks... Yes No 13. Body shall have a 5 year manufacturers warranty, first 3 years at 100%, last two years at 50%... Yes No 5. HOIST 1. Hoist system to be a dual cylinder dual support arm hoist design with a 1,500-psi relief pressure... Yes No 2. Double acting, 6 inch nominal diameter with minimum 32 ½ inch stroke cylinders... Yes No 3. Cylinder s piston rod to be Chrome to prevent weathering and increase the life of cylinder s packing... Yes No 4. Hoist to include a remote line grease kit for ease of greasing... Yes No 5. Hoist must supply a minimum 50-degree dump angle... Yes No 6. Hoist to have a minimum NTEA Class 90 rating with a lifting capacity of no less than 28.4 ton with a 14-foot body... Yes No 7. Rear hinge blocks will be supplied with grease zerks for direct lubrication... Yes No 8. Body raised warning light shall utilize factory warning in the dash... Yes No 9. The body shall be equipped with approved body props... Yes No 10. Hoist shall have a 5 year manufacturers warranty, first 3 years at 100%, last two years at 50%... Yes No SECTION III - ATTACHMENTS / LIGHTING SYSTEM / TANKS / WIRING 1. PLOW HITCH 1. Truck hitch shall be Husting 34 inch quick hitch... Yes No 2. Thrust arms braced to truck frame... Yes No inch structural channel front bumper finished, primered, and painted Gloss Black... Yes No 4. Front bumper ends to be angled to provide clearance for 12 foot swing blade and protect truck fenders... Yes No 5. The open area between bumper and fender shall house a tool box to hold the tow chain and be mounted on Driver s side... Yes No NOTE: Box to be mounted to backside of bumper on Driver s side

12 Page 12 of Bumper and hitch assembly to be bolted to truck frame, not welded, to assist in servicing pump... Yes No 7. Cylinder shall be a minimum 3 inch x 10 inch double acting lift cylinder... Yes No 8. Provide Stainless Steel poppet style quick couplers for snow plow reversing... Yes No 9. Couplers to be mounted horizontally on D/S hitch or frame, facing towards the D/S side of the truck... Yes No 10. All quick couplers shall be Parker BH-4-60, BH-4-61, BH-6-60, BH Yes No 11. Hitch to be 12 inches off the ground... Yes No 12. Rubber bumpers mounted on top of hitch to protect hood when tilted open... Yes No 13. Cushion relief valve to be installed for plow angling... Yes No 2. H-D UNDERBODY SCRAPER 1. Underbody to be Monroe MS3512 or equivalent... Yes No 2. Moldboard to be 20 inch high x 1 inch thick x 12 long, heat-treated carbon steel... Yes No 3. Cutting edge to be two (2) section 3/4 inch x 8 inch x 72 inch... Yes No 4. Moldboard cushioned by two (2) heavy duty, totally enclosed compression springs... Yes No 5. The hanger board manufactured from ½ formed plate, reinforced with ½ x 7.7 flat plate and ¾ x 2 bar on edge... Yes No 6. Hanger board hinge line to be 96 linear inches minimum, with solid hinge shaft of 2 1/2 inch O.D. carbon steel, with minimum three (3) hinge to moldboard anchor points... Yes No 7. Hanger board circle clamps to have total bearing surface of 102 sq. inches, and include replaceable 3/8 inch poly wear-pads Yes No 8. Spring shock assemblies to be mounted horizontally on the scraper by 3/4 inch reinforced steel trunnion brackets, with down pressure relief valve. DOWN PRESSURE TO BE SET AT 500 #... Yes No 9. Actuating cylinders contain inch socatri rods with poly pack seals... Yes No 10. Trunnion bearings to be 2-3/4 inch O.D. x 2 inch carbon steel... Yes No 11. Circle to be 1 inch thick solid steel 1-piece non-slotted design... Yes No 12. Circle to be equipped with ¾ hardened bushing for center bolt that is piloted into the hanger board... Yes No 13. Reversing circle to pivot with a five-inch (5 inch) center pin... Yes No 14. Circle pivot point reinforced by 6-1/2 inch O.D. x 1-1/2 inch thick bushing... Yes No 15. Circle to be mounted with 3/4 inch -thick formed steel chassis mounting brackets... Yes No 16. Reversing cylinders (2) to be Minimum 4 inch bore double acting with minimum 2 inch socatri rods... Yes No 17. Reversing cylinders to be equipped with crossover relief valve. (No exceptions)... Yes No 18. Reversing cylinders attached both to hanger board and circle by 3/4 inch replaceable bolts; 3/4 inch ID replaceable grease bushings, and fully welded 3 inch bosses... Yes No 19. Reversing mechanism to be adjustable up to 45 degrees left and right... Yes No 20. Reversing mechanism cylinders shall attach to circle through 2 inch diameter pins, front & rear... Yes No 21. Reversing mechanism Angle cylinders protected by cushion valve... Yes No 22. Reversing cylinders to contain replaceable polyurethane rod seals, and head gland retainers of cold drawn steel to prevent damage during removal... Yes No 23. All moving parts equipped with grease line extension hoses and grease line manifolds... Yes No 24. Replaceable moldboard carbide curb shoes both ends... Yes No 25. The scraper shall have wire mesh welded on top of the D/S full top to bottom of blade... Yes No 26. Prior to assembly the scraper mounting components and scraper moldboard will be shot blasted, washed and prepped prior to powder coating... Yes No

13 Page 13 of Scraper mounting components and scraper moldboard will be powder coated black... Yes No 28. The scraper shall have both ends painted Orange including the wire mesh on the D/S... Yes No INSTALLATION NOTE: THE MOUNTING OF THE CIRCLE PLATE TO THE FRAME SUPPORTS SHALL BE DONE UTILIZING THE FOLLOWING CRITERIA: There will be ZERO clearance between the mounting plates and the Circle plate The bolts used for mounting shall be installed with the nut on the outside in plain view The bolts shall have a minimum of ½-inch of threads showing after the nuts are torqued to specifications per size All nuts shall be Grade 8, and tack welded to the bolt to prevent vibrating off Circle to be mounted level to ground front-to-rear from bottom of circle to ground Prior to installation, unit to be pre-loaded with weight to simulate weight of box, cylinders, hydraulic system, etc 3. RIGHT WING PLOW MONROE OR EQUIVAQLENT WING PLOW WITH REVERSE CURVED STEEL CUTTING EDGE WITH TWO CAST IRON MOLDBOARD SHOES 1. Wing shall be designed to mount behind the underbody blade and shall have moldboard length of 113 inches at the top and 108 inches at the bottom... Yes No 2. Moldboard height shall measure 33 inboard and 33 outboard with cutting edge... Yes No 3. Moldboard shall be 3/16 A36 steel... Yes No 4. Top of moldboard shall be formed into a 2-3/4 X 1 channel for additional strength... Yes No 5. Bottom angle shall be 4 X 4 X ¾ and reinforced between the cutting edge holes with ten (10) 3 X 3 X ½ gussets... Yes No 6. There shall be six (6) ½ moldboard reinforcement ribs tapered from 4 at the bottom to 2-1/2 at the top... Yes No 7. There shall be two (2) horizontal reinforcement angles between the discharge end last two ribs... Yes No 8. Bottom 4 X 3 X ½ reinforcement angle shall have seven (7) evenly spaced 5/8 holes for push arm adjustment... Yes No 9. Top 4 X 4 X ½ reinforcement angle shall have seven (7) evenly spaced 5/8 holes for push arm adjustment... Yes No 10. Pivot pin shall be constructed of 1-1/2 steel... Yes No 11. Front attachment pivot plate will be ½ steel, completely boxed and supported with ½ and 3/16 plate... Yes No 12. Pivot tube for the 1-1/2 pivot bolt shall have a minimum.625 wall and be welded 100% to the inside of the ½ plate and outside of the moldboard... Yes No 13. A ½ safety stop eyelet shall be on the front of the moldboard and a ½ centered lift loop... Yes No 14. All seams and joints shall be 100% continuous welded... Yes No 15. Reverse curved steel cutting edge with no moldboard shoe shall be bolted on with the cutting edge... Yes No 16. One (1) 4 and One ( 1 ) 5 cutting edge shall be installed on the toe end and the heel... Yes No 17. Bottom of cutting edge shall be cut at approximately 10 degrees to match attack angle of moldboard... Yes No 18. A ½ X 4 X 6 cross tube passing thru two (2) mounting plates of 36 tall X 12 wide X 1/3 for mounting the wing to the frame of the truck... Yes No 19. The cross tube shall pass behind the underbody blade Circle... Yes No 20. Pin for banjo plate shall be 1-1/2 diameter... Yes No 21. Banjo plate/hinge for moldboard shall be fabricated of ¾ material, reinforced with ½ bar and have two (2) thick reinforced ears for the hinge pin... Yes No 22. The bolt for retaining the moldboard shall be 1-1/2 6 X 7 G8 HHCS Zinc plated with castle nut and cotter pin... Yes No 23. The wing post shall be a parallelogram design to allow the toe of the wing moldboard to float freely over rough roads and

14 Page 14 of 27 road shoulders, thus reducing potential damage to the wing and cab chassis... Yes No 24. The wing post shall be a trailing link style with 12 of lift and designed to allow the moldboard to float up to a minimum of 8-12 when in the plowing position... Yes No 25. The post front structure shall be no more than 24 high and 14 wide... Yes No 26. The post weldment shall be manufactured with ¾ inside mounting plate and a matching ½ outer plate... Yes No 27. A 3/8 Ex-Ten 50 front base plate will set the width of the post, support the inner lower hinge brackets and the bottom cylinder mounts... Yes No 28. Internal reinforcement with a.500 HSLA radius plate shall be welded to both side plates and the front base plate... Yes No 29. The post weldment will serve as the anchor for three trailing link assemblies... Yes No 30. The upper and lower link arms shall be ¾ radius bar with a 1 ¾ machined hole on end... Yes No 31. The upper arm assembly will be reinforced with a 2 ½ schedule 80 pipe at the front anchor... Yes No 32. The lower arm assembly will be reinforced with a 2 ½ schedule 80 pipe at the front anchor and.500 HSLA x plate to the rear... Yes No 33. The lift/float link will be ½ bar with a radius at the anchor end, reinforced with a 2 ½ schedule 80 pipe... Yes No 34. The rear of the lift link will be 1 plate reinforced with 5/8 bar and will include two 5/8 upper cylinder mounts... Yes No 35. The rear lift weldment shall have an outer 1 and inner ½ bar with radius ends and machined 1 ¾ holes... Yes No 36. Bars shall be spaced and supported with two 2 ½ schedule pipes and two ½ x 4 triangular gussets... Yes No 37. The hinge shall consist of three 1 thick radius ears that have machined holes, spaced evenly and reinforced with two ¼ x 2 x 2 angles... Yes No 38. All 1 ¾ machined holes will have Rc 50 hardened bushings... Yes No 39. Hinge pins shall be 1 ½ OD, case hardened to Rx Yes No 40. Hinge pins shall be retained with machine bushings and ¼ roll pins... Yes No 41. There shall be grease zerks on all pivots... Yes No 42. Lift cylinder shall be a 3 ID x 5 stroke with a nitrated rod... Yes No 43. Hydraulic port(s) shall be ORB... Yes No 44. Cylinder shall be attached within the post with 1 stress proof pins, machine washers and roll pins... Yes No 45. Prior to assembly, the post will be shot blasted, washed and prepped prior to powder coating black... Yes No 46. The rod end shall have an offset cross tube mount to eliminate side load on the cylinder... Yes No 47. Slide cylinder shall have ¾ - 16 ORB ports and poly-pac seals... Yes No 48. Lifting action for the heel end of the wing shall be accomplished via a single 3 ID X 15 stroke, 2 rod, ¾ - 16 ORB ports, poly-pac seals, double acting hydraulic cylinder... Yes No 49. Heel cylinder shall be attached to the upper rear push arm slide assembly... Yes No 50. Wing shall be operated by hydraulic lift; no cables or chains shall be accepted... Yes No 51. Rear wing mount shall be fabricated from 5 X 7 X 3/8 mild steel tubing, and shall attach between the drive axles... Yes No 52. The tubing shall include a ½ mounting plate that attaches at the trunnion and shall include tubular gussets... Yes No 53. Rear channel push arm/cylinder mounting plate shall include two (2) ½ plates, flame cut with three (3) offset mounting holes to mount the rear push arms and the heel lift cylinder... Yes No 54. The rear upper push arm shall be equipped with an external slide assembly to allow for mechanical float and attachment of the heel lift cylinder... Yes No 55. Rear push arms and heel lift cylinder shall be attached with 1-1/4 stress proof pins for quick attach and detach... Yes No 56. There shall be two (2) rear wing heavy duty, 2-1/2 schedule 80, adjustable, spring cushioned lift arms including safety shear pins, 6 long fully extended... Yes No 57. All fabricated components shall be shot blasted and washed prior to powder coating... Yes No 58. Mounting components shall be powder coated black... Yes No

15 Page 15 of All welding on the moldboard shall be 100% continuous... Yes No 60. Mounting hardware shall include schedule 80 pipe bracing, two (2) pipe balls, a flame cut ¾ support plate, Grade 8 nuts, bolts and washers necessary for a complete installation... Yes No 61. A sequencing valve shall be supplied with the wings... Yes No 62. Sequencing valve shall be adjustable for both the up sequencing of the wing and the down sequencing of the wing... Yes No 63. Lock valves built into the sequencing valve to prevent both the toe and heel cylinder from drifting when in the stored position... Yes No 64. The sequencing valve shall allow wing to hydraulically drift up when in the plowing position... Yes No 65. Sequencing valve shall be equipped with an adjustable metering valve to control the speed at which the blade drops when going from the stored position to the plow position... Yes No 66. Wing assembly shall be furnished with proximity switch to operate a Wing Down light... Yes No 67. A rear facing LED for wing location shall be controlled by an Operator On/ Off switch.... Yes No 68. A work light will be mounted in front of the wing assembly... Yes No 69. Controls for wing shall be incorporated in the electronic joystick... Yes No 70. All hydraulic fittings/ hoses & shuttle for interconnect of the system... Yes No 71. Manuals for Operation/ Parts & Service... Yes No 72. Prior to assembly, the wing post, all wing mounting components and the moldboard will be shot blasted, washed and prepped prior to powder coating... Yes No 73. Wing post and mounting components to be powder coated black. Wing moldboard to be powder coated orange... Yes No 74. All truck frame to wing fittings need to be quick disconnect fittings... Yes No 4. FUEL TANK 1. Fuel tank to be constructed to meet Federal Motor Vehicle Safety Regulations , Yes No 2. Tank to be 100 usable gallons, shape to be determined by space provided behind the cab... Yes No 3. Fuel and hydraulic tank are to be integrally designed and mounted behind the cab on the drivers side... Yes No 4. Mounting of the combination tank shall include mounting brackets with rubber bushings... Yes No 5. Heavy-duty, 7 gauge steel tank construction... Yes No 6. Fuel tank must be labeled Diesel Fuel, Hydraulic tank must be labeled Hydraulic Oil... Yes No 7. Fuel tank shall meet the following requirements:... Yes No Tank shall be FWHA tested and certified... Yes No Fuel tank shall have raised filler neck with screw-on cap... Yes No Fuel pick up and return ports must be located on top of tank... Yes No Fuel tank shall have solid-state electronic sending unit for fuel gauge with no moving parts... Yes No Fuel gauge will sense fuel level within 2 inch of tank bottom... Yes No Drain plug to be installed... Yes No 8. Combination tank to be powder coat painted to match cab... Yes No

16 Page 16 of SNOW PLOW AND AUXILLARY LIGHTS: 1. Truck Lite brand TL80800 auxiliary snowplow head lights to be mounted on hood of cab... Yes No 2. Snowplow lights mounted with a rubber-mounting pad to reduce vibration and provide adequate support... Yes No 3. Brackets must be fabricated from aluminum and be ¼ thick stock... Yes No 4. Height from ground to bottom of plow light to be 80 Inches and adjustable up or down... Yes No 5. Snowplow lights to be wired into factory harness to factory switch on dash... Yes No 6. Plow lights to be wired to operate either snow plow lights or normal truck head lights... Yes No 7. One rubber housed sealed beam light shall be mounted behind the driver s side to illuminate the salt spread pattern, protected with steel guard, wired to factory switch on dash... Yes No 8. One rubber housed sealed beam light shall be mounted behind the passenger side to illuminate the underbody blade and wired to the factory auxiliary switch on dash... Yes No 9. Wires to lights must be enclosed in loom and any connections made sealed with shrink tube... Yes No 10. Ground wire for lights must be routed to fire wall and connect to a protected independent ground point for reliable operation... Yes No 6. REAR SAFETY LIGHTING SYSTEM 1. Sound-Off brand LED flashing lights to be used... Yes No 2. LED flashers, Stop/turn/tail lights shall be flush mounted in a 201 or 304 SS, wedge-shaped protective box... Yes No 3. Wedge boxes shall be solid welded to the outside the rear corner posts of the dump body... Yes No 4. There shall be a Three (3) LED lighting system consisting of: Top Oval Amber LED flasher - (Sound-Off EOVREBZA)... Yes No Middle Oval Red LED STT - (Sound-Off ECVO62STT)... Yes No Bottom Oval Amber LED flasher - (Sound-Off EOVREBZA)... Yes No Oval Backup light - (Sound-Off ECVO62B2W) to be high mounted in inside corner posts... Yes No 5. Rear LED flashers only to have an integrated circuit to interrupt/shutoff the strobes when the brake or backup lights are activated... Yes No 6. All LED flashers to operate from a single factory mounted switch on the dash... Yes No 7. OVERHEAD STROBES 1. Four Sound-Off Predator (EP2SSMDBAC) flush mounted LED flashers mounted on sides and front of cab shield Yes... No 2. LED flashers shall have stainless steel ¼ rod - brush guards mounted over them to prevent damage... Yes No 3. Weather-pack wiring connectors to be utilized... Yes No

17 Page 17 of WIRING NOTE: ABSOLUTELY NO SCOTCH LOCKS, CRIMPED CONNECTORS OR EQUIVALENT WILL BE ACCEPTED ANYWHERE IN THE WIRING SYSTEM. 1. Shall meet or exceed Federal Motor Vehicle Safety Regulation Yes No 2. Main harness ground wire running through the shall be 10 gauge wire... Yes No 3. All other attachments with grounds shall have separate grounds of 14 gauge wire... Yes No 4. Wiring harnesses shall be of water-tight, multi-conductor, quick change, plug-in type for corrosion resistance... Yes No 5. All harness shall be rubber wrapped cable, splices to be soldered and seal-type shrink-tubing used... Yes No 6. The wiring harness will be clamped at all ends of the wiring harness, outside of the cab, shall end in a sealed junction box... Yes No 7. Junction boxes shall be sealed from elements and be placed as to be easily accessible... Yes No 8. The harness will branch off from the junction box and run to the taillights, marker lights, backup beeper and lights... Yes No 9. Where the loom runs into any kind of box, it will have a sealed connector... Yes No 10. Where the loom ends at the marker lights and backup beeper, it will have the ends sealed with silicone... Yes No 11. The wiring harness will be clamped to the frame with insulated support clamps spaced no further apart than 18 inches... Yes No 12. All exposed terminals and electrical connections will be generously coated with truck light electrical grease... Yes No 13. All wiring to be placed as not to overload any one circuit... Yes No 14. All wiring and solenoids shall be covered or protected so that chains, tools etc. won t short out components... Yes No 9. TRAILER HITCH 1. Model PH45, 45 ton capacity Pintle hitch, with safety chain eyes... Yes No 2. Mount to minimum 3/4 inch thick steel plate, reinforce plate to truck frame, 24 inch from ground to center of hitch... Yes No 3. Two (2) four-inch LED red STT lights to be mounted on rear plate (Sound-Off ECVR44STT)... Yes No 4. Two (2) four-inch LED white backup lights to be mounted on rear hitch plate (Sound-Off ECVR43B2W)... Yes No 5. Backup lights shall be mounted below the red STT taillights... Yes No 6. Back up alarm 112 dba shall be activated whenever the vehicle is in reverse gear.... Yes No 7. License plate bracket and light to be mounted high center of hitch plate... Yes No 10. TARP SYSTEM (ELECTRIC TARP) 1. Tarp system shall be a Roll Rite heavy duty fully automatic electric tarp system... Yes No 2. Shall include a wind deflector, end plates and a Super Duty gear motor... Yes No 3. Shall include an external mount, four spring pivot set... Yes No 4. System shall have an aluminum tarp and tension bow set with 30 degree elbows in tarp and tension bows... Yes No 5. Tarp shall be a Super Tough mesh tarp. Location of tarp and controls shall be approved by the County prior to mounting... Yes No 6. Tarp is to be mounted to the rear of the cab-shield and inset as to not be above the sides of the shield... Yes No _

18 Page 18 of RETROFLECTIVE SHEETING SPECIFICATIONS All dump trucks shall have 3 inch retro-flective sheeting applied to its surfaces as follows: 1. Shall meet 49CFR specifications... Yes No 2. Sides of dump truck body shall have a horizontal strip of sheeting, originating and terminating as close to the front and rear ends as practicable... Yes No 3. The strip will be started with the white section towards the front of the truck and shall be continuous where possible... Yes No 4. The edge of the red sheeting cannot be located any closer than 3 inches to an amber lamp... Yes No 5. The edge of the white sheeting cannot be located any closer than 3 inches to a red lamp... Yes No 6. There shall be 2-1/2 inch front and rear reflectors on each of the body: (1) Amber on front sides of body, (Sound-Off ECVML252R)... Yes No (1) Red on rear sides of body (Sound-Off ECVML252Y)... Yes No 12. PAINT 1. All metal surfaces are to be high-pressure cleaned with a phosphate solution to remove slag, splatter, oxide, and oil residue... Yes No 2. Non-stainless steel parts to be painted high solids, polyurethane Gloss Black... Yes No 13. MISCELLANEOUS 1. Rear tow hooks to be installed... Yes No 2. Dealer supplied fire extinguisher; flare kit and triangles to be mounted in the cab... Yes No 3. Extinguisher to be mounted by driver s seat on door side... Yes No 4. A jumper wire is to be installed on the cab marker light switch... Yes No NOTE: WITH TRUCK OFF AND DISCONNECT ON, CAB MARKER LIGHTS TO REMAIN ON 5. Electric brake controller to be installed... Yes No 6. Truck to be detailed, interior to be cleaned of all grease, fingerprints, wire cuttings, caulking, left over mess... Yes No SECTION IV - SPECIFICATIONS FOR A TAILGATE SALT SPREADER This specification shall describe a Direct Drive 201 or 304 Stainless Steel tailgate material spreader capable of spreading free flowing granular materials. This unit shall consist of a 201 or 304 stainless steel body, spinner disc, power drive, and all components necessary to make a complete operating unit. Bidders must submit with their proposal complete specifications on the unit they propose to furnish. Spreader mounts on rear of dump body below regular dump box tailgate in a manner to allow use of dump with spreader attached. Tailgate may be hinged at top or at the bottom

19 Page 19 of GENERAL SPECIFICATIONS - Hydraulic power and components such as pump, tank, control valve, hoses, couplers, etc. are not included in this specification. They are to be provided with a central hydraulic system Spreader to be Monroe MS966-OW-DD or equivalent tailgate spreader 1. System shall be set up to run as a CLOSED LOOP operation... Yes No 2. Auger motor to have 60 pulses per revolution... Yes No 3. The auger shall be driven by a direct drive motor with coupler... Yes No 4. This under-tailgate spreader shall be of the bottom opening design... Yes No 5. The discharge port shall be located on the extreme left end of trough... Yes No 6. Single 6 inch heavy-duty auger shall consist of 3/8 inch flighting that is welded to a schedule 40 (ASTM) pipe... Yes No 7. This auger shall have continuous flighting to the discharge port for more uniform dump body emptying and shall be supported by 1-1/4 inch steel shaft ends... Yes No 8. The entire unit will rigidly mount to the sides of the dump body and below the floor level of the dump box with single pin (per side) quick detachable hardware made of 201 or 304 Stainless Steel... Yes No 9. This mounting shall allow the dumping of materials without interference from the spreader... Yes No 10. This hinged bottom shall be held in place by two heavy-duty cam locks with a lift handle for convenient one man operation... Yes No 11. The 10-gauge 201 or 304 stainless steel cover/back plate will be a one piece hinged integral part of the unit that may be raised when spreading and lowered when dumping... Yes No 12. The trough assembly is 7 gauge steel with ¼ one-piece gusseted endplates... Yes No 13. The trough has a 3 X2 rectangular tube rear member that shall be 96 in overall length... Yes No 14. The ¼ endplates shall extend 33 above the trough... Yes No 15. The spinner assembly is to be a self-leveling type assembly, with easy one-man mount and dismount... Yes No 16. An 18 ploy spinner disc with molded fins shall be provided with the spinner assembly... Yes No 17. A spinner shield shall be provided to prevent material from striking the truck... Yes No 18. All quick couplers shall be Parker Stainless Steel BH-4-60, BH-4-61, BH-6-60, BH Yes No 19. No stainless steel is to be painted... Yes No 20. The remaining carbon steel parts, bearings and motors, etc. are to be cleaned, primed and painted gray... Yes No SECTION V - SPECIFICATIONS FOR HYDRAULIC SYSTEM It is the intent of this specification to describe the minimum requirements for a frame mounted hydraulic system to operate a double acting hoist, spreader system, power angled front plow and underbody scraper. 1. HYDRAULIC SYSTEM 1. Pump shall be mounted to a 6 inch structural channel cross member that shall be bolted, not welded, to the truck front frame extension, for easy serviceability... Yes No 2. All hydraulic hoses with JIC fittings shall be used. Black iron pipe and elbows are not acceptable... Yes No 3. All high-pressure lines shall use o-ring type fittings, pipe thread not acceptable... Yes No 4. All hoses and control cables shall be securely fastened with rubber-coated steel clamps every 24 inches... Yes No 5. All hoses and control cables shall be protected with rubber grommets wherever they pass through sharp edges... Yes No 6. All hoses shall be covered to prevent rub wear and abrasion... Yes No 7. The hydraulic pump shall be a U.S. manufactured axial piston pressure and flow compensated load-sensing type... Yes No

20 Page 20 of The pump shall be cast iron construction and rated to 6.00 cubic inches per revolution at maximum stroke which will deliver engine rpm... Yes No 9. The pump shall have a 2 inch suction line and 3/4 inch case drain line plumbed directly back to the reservoir... Yes No 10. The pump shall be rated for 3000 PSI maximum and 2500 PSI continuous... Yes No 11. The pump shall have a 1-1/4 inch keyed drive shaft and SAE type C mounting flange... Yes No 12. A field replaceable shaft seal housing will provide service without removal of the pump... Yes No 13. The pump shall be a Hydro-Gear FASD45L piston pump or prior approved equal... Yes No 14. Hydraulic system shall be flushed out with a filtration system prior to running the hydraulic fluid through the pump... Yes No 2. SHUT DOWN SYSTEM 1. The valve shall be capable of stopping oil flow to the hydraulic system when actuated... Yes No 2. A single normally open, two position, two way, poppet style solenoid valve... Yes No 3. The valve shall be mounted directly to the hydraulic pump discharge port... Yes No 4. The valve assembly must also incorporate a high pressure relief valve to protect the system from over pressurizing during system shut down... Yes No 5. This solenoid valve shall be wired to a float type level indicator that is mounted from the top of the reservoir... Yes No 6. The system shall be designed so that when the float contacts close, the solenoid valve stops pump flow and an enunciator in the cab on a control panel alerts the driver... Yes No 7. The control panel will also incorporate an override switch wired to de-energize the shut down system to facilitate diagnostics and equipment storage... Yes No 3. MOUNTING 1. The hydraulic pump shall be mounted with shaft centerline parallel to the engine crankshaft centerline... Yes No 2. The driveline shall be Spicer 1310 series assembled with proper angle and phasing for optimum operation... Yes No 3. The shaft centerline shall not create not more than a three-degree angle on the driveline... Yes No 4. The pump mounting shall be incorporated with a bracket fabricated to mount in the extended frame rails of the truck... Yes No 5. The flange bolts, other mounting, fasting, tightening bolts shall be Grade 8 bolts, lock-tited and torqued to specifications... Yes No 4. DRIVELINE 1. The hydraulic pump shall be driven directly off the engine crankshaft via a splined driveline to allow for movement... Yes No 2. The driveline shall include grease fittings on both u-joints... Yes No 3. Driveline shall be a Spicer model 1310 series... Yes No