BATHROOM 1 _ 2018 TECHNICAL MANUAL

Transcription

1 BATHROOM 1 _ 2018 TECHNICAL MANUAL

2

3 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. MELAMINE-COATE Melamine coated with high quality resin CARCASSES CUSTOMISE COLOURS ARE NOT FEASIBLE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) 0.3

4 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. LASERMAT Nanotechnological matt soft touch FENIX NTM surface - Edge in polypropylene, applied with Laser technique * The colour Alaska white Lasermat 177, in some light conditions, tends to reveal the red pigment inside the colour formulation, causing chromatic changes. This characteristic cannot be considered cause for a compliant. FRONT PANELS PANELS TOPS BACK PANELS ** The colour Kos white Lasermat 183 is recommended for matches with white Corian 173 / white Silcover 003 / Arctic white Ecolak 510. The external decorative surface is obtained starting from thermosetting last generation resins that, thanks to the use of nanotechnology (NTM), make the surface extraordinary from a mechanical, aesthetic and functional point of view. CUSTOMISE COLOURS ARE NOT FEASIBLE The internal structural layer is obtained through the thermo-lamination of kraft papers, soaked in thermosetting resin. 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black 0.4

5 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. SILCOVER Matt lacquered, fine textured * The colour white Silcover 003 is recommended for matches with white Corian 173 / Kos white Lasermat 183 / Arctic white Ecolak 510 / white Polyester 003. FRONT PANELS PANELS BACK PANELS ** The extra charge has to be applied to the price of cabinets, SILCOVER category. Please consider a 4 weeks time increase for supply of goods. Fluorescent or metalized colours are not feasible. Attention! ice increases start from a minimum value of 200,00 (net dealer value, VAT excl.). Custom colour requests with price increases of lesser amounts are considered equal to the minimum charge. ice increase for CUSTOMISE COLOURS ** +10% RAL or NCS colours +18% AS PER SAMPLE colours 003 White * 129 Magnolia 119 Grey 024 Pebble grey 131 Sand 025 Ècru 023 Mud 134 Graphite-grey 118 Black 0.5

6 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. ECOLAK Water-based matt Soft touch lacquer * The colour Arctic white Ecolak 510 is recommended for matches with white Corian 173 / Kos white Lasermat 183 / white Silcover 003 / white Polyester 003. FRONT PANELS PANELS BACK PANELS CUSTOMISE COLOURS ARE NOT FEASIBLE 510 Arctic white * 129 Magnolia 513 Cloud colour 024 Pebble grey 512 Oat colour 025 Ècru 023 Mud 515 Basalt grey 517 Charcoal 027 Black 0.6

7 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. VENEER WOO * Finished with water-based paint. ** Finished with acrylic-based paint. FRONT PANELS PANELS BACK PANELS Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials (Abonos Oak excluded). ABONOS OAK: fossil oak wood found in river basins, result of thousands of years of underwater conservation ( BC), which gives the wood several properties including hardness and giving it distinct light to dark colour tones, unique grains that enhance the wood rarity and the special design. Attention! oors and panels have vertical grain, except for specific cases indicated on relative product pages. SPECIAL OR CUSTOMISE SPECIES ARE NOT FEASIBLE ice range > WOO 049 Oak ** 033 Ash-grey oak * 076 Grey-graphite oak ** 331 Larch wood, Aspen white * 332 Larch wood, Orion black * Black Eco-wood ** ice range > WOO SELECTION 048 Core walnut * 093 Canaletto walnut U.S. ** 101 Smoked oak * NEW ice range > WOO EXCLUSIVE 077 Abonos oak * 0.7

8 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. POLYESTER Polyester hi gloss lacquer * The colour white Polyester 003 is recommended for matches with white Corian 173 / Kos white Lasermat 183 / white Silcover 003 / Arctic white Ecolak 510. FRONT PANELS PANELS ** The extra charge has to be applied to the price of cabinets, POLYESTER category. Please consider a 4 weeks time increase for supply of goods. Fluorescent or metalized colours are not feasible. CUSTOMISE COLOURS ARE NOT FEASIBLE 003 White * 129 Magnolia 005 Grey RAL Pebble grey 063 Sand 106 Sahara 004 Grey 007 ark green 027 Black 001 Andalusian red 0.8

9 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. METALS Metal-effect lacquer Attention! Metals is a special finishing which reproduces the typical effect of metallic surfaces, rendered through a very precise and technical sequence of production cycles. The characteristic metallic effect of the surface is given by the alternation of manual and mechanical processes, by the quality of the chromium particles-enriched acrylic paints and by the complex drying procedure. The various shades of colour (halos caused by the spread of the paint chromium particles) and the succession of multi-directional brushing of the surface make each piece a unique and exclusive one. The above mentioned characteristics shall not be considered cause of complaint. FRONT PANELS PANELS CUSTOMISE COLOURS ARE NOT FEASIBLE 934 Aluminium 194 Magnesium 192 Titanium 191 Lead ALUMINIUM Anodised aluminium sheet * Brushed finish. FRONT PANELS PANELS FRONT PANELS (ON FRAME AMX) ** Micro-sandblasted finish. CUSTOMISE COLOURS ARE NOT FEASIBLE 382 Steel * 381 ark ** 0.9

10 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. WOO 3 Veneer wood, slats effect, alternating thickness 20 /23 mm * Finished with water-based paint. ** Finished with acrylic-based paint. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials. 3 Attention! oors and panels have vertical grain, except for specific cases indicated on relative product pages. FRONT PANELS PANELS SPECIAL OR CUSTOMISE SPECIES ARE NOT FEASIBLE 048 Core walnut * Black eco-wood ** 0.10

11 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. SOLI WOO Solid wood layers, with support made of strip wood * Front panels and panels: finished with vegetable oils. / Tops: finished with water-based paints. ** Finished with special painting cycles, that don t change the old aspect of the wood. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials. Attention! oors and panels have vertical grain, except for specific cases indicated on relative product pages. The solid Canaletto LIGHT walnut with sawn effect may have parts with lighter grain alternating the dark one. The old grey pinewood 057 consists of pinewood solid boards recycled from renovation of old houses, barns and huts. The characteristic grey tone of this material is obtained by specific painting cycles, which give the typical old aspect to this wood. Possible cracks and deformations have to be considered characteristic part of the product. Since these pieces are very unique, they have the typical appeal of imperfect things and they clearly display sign of times and bad weather; therefore they show deformations and wrinkles strength. Tops obtained with old wooden boards offer a clear example of the wood vitality and instability. For this reasons each piece in solid wood has to be considered unique and different from all the other ones. The above mentioned characteristics shall not be considered cause of complaint. FRONT PANELS PANELS TOPS SPECIAL OR CUSTOMISE SPECIES ARE NOT FEASIBLE 058 Canaletto LIGHT walnut sawn-effect * Available, upon request, without sawn effect (same price). 057 Old grey pinewood ** 050 Natural oak (with knots) Exclusive finish feasible ONLY for FLYER tops and drawer units. SOLI WOO 3 Slats, alternating thickness 20 / 23 mm - Solid wood layers, with support made of strip wood FRONT PANELS PANELS * Finished with natural vegetable oil-based waxes. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials. 3 Attention! oors and panels have vertical grain, except for specific cases indicated on relative product pages. The solid Canaletto LIGHT walnut with sawn effect may have parts with lighter grain alternating the dark one. For this reasons each piece in solid wood has to be considered unique and different from all the other ones. The above mentioned characteristics shall not be considered cause of complaint. SPECIAL OR CUSTOMISE SPECIES ARE NOT FEASIBLE 058 Canaletto LIGHT walnut sawn-effect * 0.11

12 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. GLASS Tempered glass FROSTE Attention! Please consider that glasses with same colours but different thickness (e.g.: door 4 mm / top 12 mm) have always different tones. Colour of possible replacements or completions, may not match exactly the original one. FRONT PANELS TOPS BACK PANELS FRONT PANELS (ON FRAME AMX) CUSTOMISE COLOURS ARE NOT FEASIBLE 818 Frosted painted Extralight White 816 Frosted painted Extralight ove grey 817 Frosted painted Extralight Coffee GLASS Tempered glass SANE TOPS WITH MOULE WASHBASIN Attention! Please consider that glasses with same colours but different thickness (e.g.: door 4 mm / top 12 mm) have always different tones. Colour of possible replacements or completions, may not match exactly the original one. CUSTOMISE COLOURS ARE NOT FEASIBLE 818 Sanded painted Extralight White 816 Sanded painted Extralight ove grey 817 Sanded painted Extralight Coffee 0.12

13 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. CRISTALPLANT Aluminium tri-hydrate with polyester / acrylic resins and pigments TOPS WASHBASINS BATHTUBS CUSTOMISE COLOURS ARE NOT FEASIBLE - White CORIAN Aluminium tri-hydrate with acrylic resins and pigments FRONT PANELS PANELS TOPS WASHBASINS BATHTUBS CUSTOMISE COLOURS ARE NOT FEASIBLE 173 White 0.13

14 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. CERAMILUX Natural mineral charges with polyester resin, covered by a polyester acrylate film WASHBASINS BATHTUBS CUSTOMISE COLOURS ARE NOT FEASIBLE - Matt white - Polished white PAPERSTONE % eco-friendly matt material, made of recycled paper, resins not derived from petroleum and natural colours CONTENITORI UEC Certifications: FSC - NSF - Rainforest Alliance - U.S. Green Building Council. CUSTOMISE COLOURS ARE NOT FEASIBLE 080 Black 0.14

15 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. STONE - MARBLE - GRANITE Natural material extracted from quarry. Matt finish * The front panels (on frame AMX) are feasible ONLY in Carrara white marble, Cardoso stone, absolute black Zimbabwe granite, Quartzite Silver, Emperador ark marble, Black Cosmic granite, marble Grey Stone, Quartzite Calacatta. TOPS BACK PANELS WASHBASINS BATHTUBS FRONT PANELS (ON FRAME AMX) * CUSTOMISE COLOURS ARE NOT FEASIBLE ice range > STONE A 240 Marble White Carrara 250 Stone Serena ice range > STONE B 200 Stone Cardoso 245 Stone Matraia 199 Granite Black absolute Zimbabwe ice range > STONE C 257 Quartzite Silver ice range > STONE 254 Granite Black Cosmic 261 Marble Emperador ark NEW ice range > STONE E 259 Quartzite Calacatta 260 Marble Grey Stone 0.15

16 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. COMPOSITE SILESTONE Compound made up of natural quartz, polymers and pigments. Matt finish TOPS BACK PANELS WASHBASINS CUSTOMISE COLOURS ARE NOT FEASIBLE ice range > STONE C 432 Expo grey 433 Concrete grey 435 Tebas black ice range > STONE 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope grey-brown 440 oradus black 0.16

17 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. COMPOSITE EKTON Very compact surface composed of quartz, materials used to produce glass and ceramic, treated with Sinterized Particle Technology and ultra-compaction process. TOPS BACK PANELS CUSTOMISE COLOURS ARE NOT FEASIBLE ice range > STONE 455 Edora beige 452 Kadum brown 453 Sirius black ice range > STONE E 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 0.17

18 C o l o u r s - W o o d s p e c i e s 1) For a correct evaluation of finishes and colours it is necessary to use physical samples. The wood, solid wood, stone, marble and granite samples are purely indicative: these materials may present some natural and unavoidable changes in tone and grain compared to the original samples. 2) ifferent materials and finishes when compared, even if produced with the same colour (e.g. white) may present some unavoidable tone differences. 3) All finished parts may change tone and colour with time, due to light effect and to the natural aging process and to any factor which may be present into the environment: therefore possible replacements may have some differences if compared to the original finishes. These issues shall not be considered cause of complaint. E CASTELLI METALS Exclusive-appearance metal sheet obtained with special chemical and / or mechanical treatments Attention! *oors and panels are vertically striped, except for specific cases indicated on relative product pages. FRONT PANELS (ON FRAME AMX) CUSTOMISE COLOURS ARE NOT FEASIBLE ice range > E CASTELLI A 353 élabré iron B 354 Striped Maistral stainless steel 7022 * NEW NEW ice range > E CASTELLI B 355 élabré brass 356 Striped delabrè brass * 351 élabré copper NEW NEW NEW 352 Orbitale délabré cop NEW 0.18

19 P r i c e r a n g e FURNITURE Some cabinets, for technical reasons, may have restrictions and/or price relationships different from what indicated on this chart. FURNITURE PRICE RANGE TYPE OF MATERIAL COLOURS / SPECIES PRICE LASERMAT Nanotechnological matt soft touch FENIX NTM surface - Edge in polypropylene, applied with Laser technique LASERMAT colour range SILCOVER Matt lacquered, fine texture SILCOVER colour range ECOLAK Water-based, soft touch matt lacquered ECOLAK colour range WOO Veneer wood Oak / Ash-grey oak / Grey-graphite oak / Larch wood, Aspen white / Larch wood, Orion black / Black Eco-wood POLYESTER Polyester hi gloss lacquer POLYESTER colour range WOO SELECTION Veneer wood Core walnut / Canaletto walnut U.S. / Smoked oak METALS Metal-effect lacquer Aluminium / Magnesium / Titanium / Lead WOO 3 Veneer wood, planks effect Core walnut / Black eco-wood CORIAN Corian White GLASS Tempered glass (on frame AMX) Frosted painted Extralight White / ove grey / Coffee SOLI WOO Solid wood (even surface) Canaletto LIGHT walnut sawn-effect / Old grey pinewood SOLI WOO 3 Solid wood (planks, alternating thickness 20 / 23 mm) Canaletto LIGHT walnut sawn-effect WOO EXCLUSIVE Veneer wood Abonos oak ALUMINIUM Anodised aluminium (on frame AMX) Steel / ark E CASTELLI A Metal sheet (on frame AMX) élabré iron B / Striped Maistral stainless steel 7022 E CASTELLI B Metal sheet (on frame AMX) élabré brass / Striped delabrè brass / élabré copper / Orbitale délabré cop STONE A Marble, stone, granite (on frame AMX) Marble White Carrara STONE B Stone Cardoso / Granite Black absolute Zimbabwe STONE C Quartzite Silver STONE Marble, stone, granite (su cornice AMX) Granite Black Cosmic / Marble Emperador ark STONE E Marble Grey Stone / Quartzite Calacatta

20 P r i c e r a n g e TOPS Some worktops, for technical reasons, may have restrictions and/or price relationships different from what indicated on this chart. TOPS PRICE RANGE TYPE OF MATERIAL COLOURS / SPECIES PRICE LASERMAT Nanotechnological matt soft touch FENIX NTM surface - Edge in polypropylene, applied with Laser technique LASERMAT colour range CRISTALPLANT Cristalplant White GLASS Glass tempered Frosted painted Extralight White / ove grey / Coffee Sanded painted Extralight White / ove grey / Coffee CORIAN Corian White STONE A Marble, stone, granite, composite Marble White Carrara / Stone Serena STONE B Marble, stone, granite, composite Stone Cardoso / Stone Matraia / Granite Black absolute Zimbabwe STONE C Marble, stone, granite, composite Quartzite Silver Silestone Expo grey / Silestone Concrete grey / Silestone Tebas black STONE Marble, stone, granite, composite Granite Black Cosmic / Marble Emperador ark Silestone Zeus white / Silestone Lagoon white / Silestone Yukon white / Silestone Kensho grey / Silestone Unsui brown / Silestone Merope grey-brown / Silestone oradus black ekton Edora beige / ekton Kadum brown / ekton Sirius black STONE E Marble, stone, granite, composite Marble Grey Stone / Quartzite Calacatta ekton Zenith white / ekton Irok beige / ekton Strato grey / ekton Ventus grey / ekton Korus grey / ekton Galema brown / ekton Galema brown SOLI WOO Solid wood Canaletto LIGHT walnut sawn-effect / Old grey pinewood

21 G e n e r a l t e c h n i c a l i n f o r m a t i o n CARCASSES / HARWARE MELAMINE-COATE CARCASSES (A) ogramma STANAR - SIMPLE - XILA BATH - SOHO - B14 - FREE ZONE It s made of 19 mm thick wood particle board panels, waterproof (class V - In compliance with EN317 standards), with low formaldehyde emission (class E1 - In compliance with EN717+EN 120 / CARB P2 standards), treated with high performance melamine resin. Front and back edges in ABS, same colour. Back panel made of 3,5 mm thick MF Medium ensity fibres board, treated with high performance melamine resin, in same finish as carcass. Each carcass is fitted with a soft close system (Blumotion): the device is integrated in the hinge on hinged doors and in the glide on drawers. In some specific cases, the Blumotion device is installed on the carcass (instead of hinge/glide). Side panels are connected in the back through longitudinal beams in black anodised aluminium. All drillings holes for shelving are filled with galvanised metal bushes. Hardware, when used, is made of anti-oxidation treated nickel-plated metal. The nominal carcass width has a ± 1 mm allowance. Shelves brackets in stainless steel, equipped with a special blocking device (C / ). ATTENTION! - To avoid any breakage, please move the shelves using ONLY the screwdriver. O NOT use the cordless drill or other tools. COLOURS / SPECIES: 130 Silk white (C) Grey-graphite oak () / 606 Elm wood. A C B FINISHE SIE PANELS (B) ogramma STANAR - SIMPLE The visible side panels of all compositions of PROGRAMMA STANAR and SIMPLE ARE FINISHE, WITHOUT AN EXTRA CHARGE (please note that front panels in Corian have finished side panels in white Ecolak and front panels in Wood 3 have finished side panels in wood veneer - without 3 effect). The finished side panel includes the finishing of the frontal vertical edge too (Lasermat excluded - the edge remains in melamine). ATTENTION!!! - The finished side panel IS NOT FEASIBLE in SOLI WOO and 3 SOLI WOO: for these finishes please order the end panels separately. FINISHE CARCASSES I FIUMI ST E SILCOVER: MF medium density fibres, 19 mm thick, matt fine textured lacquered (E). LEGNO: MF medium density fibres, 19 mm thick, veneered with 0,6 mm thick wood veneer; 1 mm thick wood edge. 45 front and upper edges. MELAMINE-COATE CARCASSES TREVES F G It s made of 14 mm thick wood particle board panels, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. The panels are assembled using the 45 folding technique. Back panels are made of MF medium density panels - 3,5 mm thick - melamine-coated in thermo-treated larch finish. Exclusive hinge esign Boffi in black anodised aluminium (G). 180 opening. Visible external part, integrated in door thickness (14 mm). Hinge settings are the traditional ones. Finish WHITE + THERMO-TREATE LARCH WOO: external part and edges in white melamine, internal part and shelves in melamine thermo-treated larch (F). 0.21

22 G e n e r a l t e c h n i c a l i n f o r m a t i o n CARCASSES / HARWARE FINISHE CARCASSES PIANURA H I oduced with MF medium density fibres, 19 / 22 mm thick, matt lacquered Silcover or veneered with wood sheet. (H). Totally concealed adjustable hinge in printed die cast alloy, 180 opening. Covered by black plastic (I). HARWARE FOR SUSPENE BASE UNITS FOR WASHBASINS (L) In stainless steel. Exclusive technology providing increased load capacity and several adjustments. Max. capacity per each piece: 120 kg. epth adjustment: 19 mm. Height adjustment: 22 mm. L HARWARE FOR SUSPENE TALL UNITS (M) In reinforced polyamide resin. Internal adjustment devices are galvanised chromium plated steel and die cast aluminium. Please drill the wall as indicated (N). M N 30 min

23 G e n e r a l t e c h n i c a l i n f o r m a t i o n CARCASSES / HARWARE HINGES 1,2mm thick hinges made of moulded steel sheet, black onyx finish, with special spring breaking device, adjustment in height, depth and width. Opening angle 95 (P). The hinge board is a die cast alloy safely attached to the side panel. Every hinge has a Blumotion soft close system (excluded those cases where a special installation is required). P LEGRABOX RAWERS (Q) ogramma STANAR - SIMPLE - XILA BATH - FREE ZONE - SOHO - B14 - I FIUMI ST - WOO IN (with front panels assembled WITHOUT FINGER JOINT TECHNIQUE ) - B15 - QUATWO - PIANURA. Q R Side and back panels in matt black painted steel. Soft closing device. Bottom panel made of 16 mm. thick wood particle board, melamine-coated. All internal drawers (R) are provided with melamine-coated front panel, same finish as carcass (***). Customised width is available with extra charge: in those cases drawer will always be provided with melamine-coated back panel, instead of the metal one. Customised depth is not available. Glides are in galvanized steel and run on stabilized carriages. Total extraction. Capacity: 40 kg. Compatible internal accessories: OMESTICI - ONA. *** RAWERS IN WOO (S) WOO IN (with front panels assembled WITH FINGER JOINT TECHNIQUE ) S T rawer front panel, bottom, side and back panels made of 16 mm thick multi-layer wood structure, veneered with very thick sheets, edges in wood. Front panels and sides assembled with finger joint technique (T). Push opening system TIP-ON. Soft closing device. Glides are in galvanized steel and run on stabilized carriages. Total extraction. Capacity: 40 kg. Customised sizes are not feasible. Compatible internal accessories: OMESTICI - ONA. RAWER ACCESSORIES OMESTICI (U) Accessories in black-dyed ash wood. Compatible with LEGRABOX and WOO-IN drawers. U V ONA (V) Accessories in plastic, matt grey finish. Compatible with LEGRABOX and WOO-IN drawers. 0.23

24 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. PROGRAMMA STANAR - SIMPLE - FREE ZONE LASERMAT - Nanotechnological matt Soft Touch FENIX NTM surface 3 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2). 2. Covered with nanotechnological decorative paper (NTM). 3. Polypropylene edge applied with laser technique (edge seam hard to be perceived) Because of technical reasons, all panels with width shorter than 60 mm will be provided with 1 edge in ABS (3 edges in polypropylene). Colours: LASERMAT range. 23 type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE SILCOVER - Matt lacquered, fine textured R= 2 mm 1. MF medium density fibres board. 2. First coat of isolating paint imer. 3. ouble layers of polyester plastering. 4. Bottom layer of polyester. 5. Bi-components solvent fine textured paint Silcover Colours: SILCOVER range. 23 type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE ECOLAK - Matt Soft Touch lacquer R= 2 mm 1. MF medium density fibres board. 2. First coat of isolating paint imer. 3. ouble layers of polyester plastering. 4. Bottom layer of polyester. 5. Coat of isolating paint imer for corners and edges. 6. Water-based matt bi-components paint, double layers: the two coats are cross-applied Colours: ECOLAK range. 23 type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE WOO Veneer wood 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2) or in MF medium density fibres board. 2. Wood veneer 0,6 mm thick, painted in 2 steps with acrylic or water based matt paints (bottom layer + finish layer). Vertical grain. 3. Wood edge 1 mm thick. R= R= 1 2 Species: WOO range. 23 type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE 0.24

25 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. PROGRAMMA STANAR - SIMPLE - FREE ZONE POLYESTER - Polyester hi gloss lacquer R= 2 mm 1. MF medium density fibres board. 2. Three Polyester resin layers (each 320 gr/m2) sanded, smoothed and polished. Colours: POLYESTER range type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE WOO SELECTION - Veneer wood 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2) or in MF medium density fibres board. 2. Wood veneer 0,6 mm thick, painted in 2 steps with acrylic or water based matt paints (bottom layer + finish layer). Vertical grain. 3. Wood edge 1 mm thick. R= R= 1 2 Species: WOO SELECTION range. 23 type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE METALS - Metal-effect lacquer R= 2 mm 1. MF medium density fibres board. 2. Mixture of acrylic paints with metal particles. Applied with 4/5 distinct mechanical and manual processes. Colours: METALS range. 2 1 HANLE: compatible ONLY with external handles. 23 type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE CORIAN 1 1. Inner and outer face, edges made of white Corian, thickness 4 mm. 2. MF medium density fibres panel with honeycomb structure. 1 Colours: White type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE 0.25

26 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. PROGRAMMA STANAR - SIMPLE - FREE ZONE WOO 3 - Wood veneer slats effect 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 /CARB P2) or in MF medium density fibres board. 2. Wood veneer 0,6 mm thick, painted in 2 steps with acrylic or water based matt paints (bottom layer + finish layer). Vertical grain. 3. Wood edge 1 mm thick ATTENTION! - Boffi 3 door has been designed to create a specific three dimensions effect: therefore thicknesses and widths vary on purpose in a specific untidy way. - Possible small cracks on upper and lower edge may not be used as a cause for a complaint, because they are an integral part of the product itself and are due to the use of end-grain (cut perpendicularly) wood which gives a natural aspect to the door. These characteristics shall not be considered cause of complaint. Species: Core walnut / Black Ecowood type BM 2 HANLE: compatible ONLY with 3 and X3 handles, with a price increase (see page 0.34). Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE WOO EXCLUSIVE Veneer wood 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 /CARB P2) or in MF medium density fibres board. 2. Wood veneer 0,6 mm thick, painted in 2 steps with acrylic or water based matt paints (bottom layer + finish layer). Vertical grain. 3. Wood edge 1 mm thick. R= R= 1 2 Species: Abonos oak. 23 type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE SOLI WOO (thickness 23 mm) - Solid wood layers 1. Brushed solid wood layer, treated with 2 steps of natural oil or oil-based paints and vegetal waxes. Vertical grain. Horizontal sawn-effect (only on species clearly indicated) ATTENTION! - Possible small cracks on upper and lower edge may not be used as a cause for a complaint, because they are an integral part of the product itself and are due to the use of end-grain (cut perpendicularly) wood which gives a natural aspect to the door. These characteristics shall not be considered cause of complaint HANLE: compatible ONLY with external handles or with X3L handle, with a price increase (see page 0.34). Species: Canaletto LIGHT walnut sawn-effect / Old grey pinewood Abete antico Altre essenze grigio type AH Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE SOLI WOO 3 (alternating thickness 20 / 23 mm) - Solid wood vertical slats 1. Slat of solid brushed wood, treated with 2 steps of colourless natural oil. Vertical grain. Horizontal sawn effect. ATTENTION! - Boffi 3 door has been designed to create a specific three dimensions effect: therefore thicknesses and widths of solid wood vary on purpose in a specific untidy way. Upper doors (wall units) and lower doors (base units) may present slats mis-alignments. - Solid wood, with time, may present, very naturally, small cracks not pertaining to the product s quality. These characteristics shall not be considered cause of complaint. Species: Canaletto LIGHT walnut sawn-effect. type BM HANLE: compatible ONLY with X3 handle, with a price increase (see page 0.34). Feasible for: PROGRAMMA STANAR - SIMPLE - FREE ZONE 0.26

27 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS NEW 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. FREE ZONE GLASS 1. Structure made of polystyrene (multi-layer wood only on doors for electrical appliances and other specific cases). 2. Frame AMX in black anodised aluminium profile. 3. Rear covering in FENIX NTM (nanotech material). 4. Tempered glass, bevelled on inner and outer edges. Colours: Glass > Extra-light frosted painted White / ove grey / Coffee. Framework > black type TE GLAS Feasible for: FREE ZONE ALUMINIUM 1. Structure made of polystyrene (multi-layer wood only on doors for electrical appliances and other specific cases). 2. Frame AMX in black anodised aluminium profile. 3. Rear covering in FENIX NTM (nanotech material). 4. Anodised aluminium sheet Colours: Aluminium > Steel / ark. Framework > black type TE ALLUMINIO Feasible for: FREE ZONE E CASTELLI A / B - METAL 1. Structure made of polystyrene (multi-layer wood only on doors for electrical appliances and other specific cases). 2. Frame AMX in black anodised aluminium profile. 3. Rear covering in FENIX NTM (nanotech material). 4. Treated metal sheet Colours: e Castelli metal: élabré iron B, striped Maistral stainless steel 7022, élabré brass, striped élabré brass, élabré copper, orbitale élabré copper. Framework > black ,5 4 type TE E CASTELLI A / B Feasible for: FREE ZONE STONE A / B / C / / E - STONE / MARBLE / GRANITE 1. Structure made of polystyrene (multi-layer wood only on doors for electrical appliances and other specific cases). 2. Frame AMX in black anodised aluminium profile. 3. Rear covering in FENIX NTM (nanotech material). 4. Stone / marble / granite sheet, matt finish, waterproof treated Typologies: Carrara white marble / Cardoso stone / Absolute black Zimbabwe granite / Quartzite Silver / Emperador ark marble / granito Black Cosmic / Marble Grey Stone / Quartzite Calacatta. Framework > black type TE STONE - MARBLE - GRANITE Feasible for: FREE ZONE 0.27

28 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. XILA BATH - B14 SILCOVER - Matt lacquered, fine textured 1. MF medium density fibres board. 2. First coat of isolating paint imer. 3. ouble layers of polyester plastering. 4. Bottom layer of polyester. 5. Bi-components solvent fine textured paint Silcover Colours: SILCOVER range. ECOLAK - Matt Soft Touch lacquer 1. MF medium density fibres board. 2. First coat of isolating paint imer. 3. ouble layers of polyester plastering. 4. Bottom layer of polyester. 5. Coat of isolating paint imer for corners and edges. 6. Water-based matt bi-components paint, double layers: the two coats are cross-applied. Colours: ECOLAK range. 23 type BN SILCOVER - ECOLAK POLYESTER - METALS Feasible for: XILA BATH - B14 POLYESTER - Polyester hi gloss lacquer 1. MF medium density fibres board. 2. Three Polyester resin layers (each 320 gr/m2) sanded, smoothed and polished. Colours: POLYESTER range. METALS - Metal-effect lacquer 1. MF medium density fibres board. 2. Mixture of acrylic paints with metal particles. Applied with 4/5 distinct mechanical and manual processes. Colours: METALS range. WOO / WOO SELECTION / WOO EXCLUSIVE - Veneer wood 1. Wood veneer 0,6 mm thick (first choice on both faces) painted in 2 steps with acrylic or water based paints (bottom layer + finish layer). Vertical grain. 2. Wood edge thickness 0,6 mm. 3. Panel made of MF medium density fibres board Species Wood: WOO range. Species Wood Selection: WOO SELECTION range. Species Wood Exclusive: Abonos Oak. 23 type BN WOO WOO SELECTION WOO EXCLUSIVE CORIAN 1. Inner and outer face made of white Corian panel thickness 4 mm. 2. Angled edge 30 made of solid Corian thickness 19 mm. 3. Honeycomb panel with solid pinewood frame. Colours: White type BN CORIAN 0.28

29 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. XILA BATH - B14 SOLI WOO (thickness 23 mm) - Solid wood layers 1. Brushed solid wood layer (th. about 8 mm), treated with 2 steps of natural oil or oil-based paints and vegetal waxes. Vertical grain. Horizontal sawn-effect (only on species clearly indicated). ATTENTION! - Possible small cracks on upper and lower edge may not be used as a cause for a complaint, because they are an integral part of the product itself and are due to the use of end-grain (cut perpendicularly) wood which gives a natural aspect to the door. These characteristics shall not be considered cause of complaint Species: Canaletto LIGHT walnut sawn-effect / Old grey pinewood. type BN SOLI WOO Feasible for: XILA BATH - B14 STONE A / B / C / / E - STONE / MARBLE / GRANITE (thickness 23 mm) 1. Lightened wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2). Lateral and lower edges in ABS. 2. Treated with high performance melamine resin. 3. Stone / marble / granite sheet, matt finish, waterproof treated. 4. Upper profile in aluminium, black or white painted Typologies: Carrara white marble / Cardoso stone / Absolute black Zimbabwe granite / Emperador ark marble / Quartzite Silver / Marble Grey Stone / Quartzite Calacatta. Support typologies: Grey-graphite oak with black edge / Silk white with white edge / Elm wood with elm wood edge type CV STONE - MARBLE - GRANITE Feasible for: XILA BATH SOHO GLASS 1. Wood particle board panel, 16 mm thick, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2). 2. Treated with high performance melamine resin. 3. ABS edge thickness 1 mm. 4. EXTRA-LIGHT frosted glass, varnished, tempered, thickness 5 mm. Bevelled on inner and outer edges. ATTENTION! Please consider that glasses with same colours but different thickness (ex: door 5 mm / top 12 mm) have always different tones. Colour of possible replacements or completions, may not match exactly the original one Colours: Glass > Extra-light frosted painted White / ove grey / Coffee. Support > Black. type AV Feasible for: SOHO ALUMINIUM 1. Wood particle board panel, 16 mm thick, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2). 2. Treated with high performance melamine resin. 3. ABS edge thickness 1 mm mm. thick anodised aluminium sheet, STEEL (brushed finish) or ARK (micro-sandblasted finish). Colours: Aluminium > Steel / ark. Support > Black type AV 0.29

30 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. I FIUMI ST SILCOVER - Matt lacquered, fine textured 1. MF medium density fibres board. 2. First coat of isolating paint imer. 3. ouble layers of polyester plastering. 4. Bottom layer of polyester. 5. Bi-components solvent fine textured paint Silcover Colours: SILCOVER range. 23 Feasible for: I FIUMI ST WOO / WOO SELECTION - Veneer wood 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2) or in MF medium density fibres board. 2. Wood veneer 0,6 mm thick, painted in 2 steps with acrylic or water based paints (bottom layer + finish layer). Vertical grain. 3. Wood edge 1 mm thick Species Wood: ONLY oak / Grey-graphite oak / Ash-grey oak. Species: WOO SELECTION range

31 G e n e r a l t e c h n i c a l i n f o r m a t i o n OORS / FRONT PANELS 1) The thicknesses indicated in the following technical sections are nominal and may slightly differ from the true measurement: this fact is due to the inevitable tolerances of the materials and technical construction of the door/front panels. WOO-IN LASERMAT - Nanotechnological matt Soft Touch FENIX NTM surface 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2). 2. Covered with nanotechnological decorative paper (NTM). 3. Polypropylene edge applied with laser technique (edge seam hard to be perceived). Because of technical reasons, all panels with width shorter than 60 mm will be provided with 1 edge in ABS (3 edges in polypropylene). Colours: LASERMAT range NEW Feasible for: WOO IN (with front panels assembled WITHOUT FINGER JOINT TECHNIQUE ) WOO / WOO SELECTION / WOO EXCLUSIVE - Veneer wood 3 1. Wood particle board panel, waterproof (class V), with low formaldehyde emission (class E1 / CARB P2) or in MF medium density fibres board. 2. Wood veneer 0,6 mm thick, painted in 2 steps with acrylic or water based matt paints (bottom layer + finish layer). Vertical grain. 3. Wood edge 1 mm thick Species Wood: ONLY oak / Grey-graphite oak / Ash-grey oak. Species: Wood SELECTION range. Species Wood Exclusive: Abonos Oak. 16 WOO SELECTION / WOO EXCLUSIVE Veneer wood assembled with finger joint technique Panel in multi-layered wood. 2. Veneered with very thick sheets, painted in 2 steps with acrylic or matt water based paints (bottom layer + finish layer). Horizontal grain. 3. Wood edge. 4. End strip in wood, assembled with finger joint technique Species Wood Selection: ONLY Oak with knots (available only for Wood-in) / Canaletto walnut U.S. Species Wood Exclusive: Abonos oak Feasible for: WOO IN (with front panels assembled WITH FINGER JOINT TECHNIQUE ) 0.31

32 G e n e r a l t e c h n i c a l i n f o r m a t i o n STANAR HANLES No extra charge. 1) Please always specify on the order handles position: without info Boffi will consider standard position. 2) When using wide external handles on hinged door, please always check possible opening interferences. 3) With drawers, heavy-duty drawers and pull out, handles position is always centred on the door panel. SERIES AN IMENSIONS STANAR POSITIONING MATERIAL AN COMPATIBILITY HANLE Horizontal centred Moulded aluminium, painted or chrome finished. 40 Sizes: 235 mm. Colours: chrome white polished black polished Compatible cabinets: ogramma STANAR. 40 = 224 = 30 T LINE a horizontal centred Extruded aluminium, stainless steel satin finish. 40 Sizes: mm. 220 / 370 / 520 / 820 / /224/381/531/ b horizontal left or right 40 Compatible cabinets: ogramma STANAR

33 G e n e r a l t e c h n i c a l i n f o r m a t i o n HANLES WITH EXTRA CHARGE Please add the price increase cod. JZMW01 to each door or front panel, see page ) Please always specify on the order handles position: without info Boffi will consider standard position. 2) When using wide external handles on hinged door, please always check possible opening interferences. 3) With drawers, heavy-duty drawers and pull out, handles position is always centred on the door panel. SERIES AN IMENSIONS STANAR POSITIONING MATERIAL AN COMPATIBILITY ZONE Horizontal or vertical centred Totally in stainless steel. The black version is treated with PV coating technology. Touch latch opening with spring. 40 Sizes: 200 mm. = = Colours: Stainless steel - black PV NEW Compatible cabinets: ogramma STANAR. Compatible finishes: Lasermat - Silcover - Ecolak - Wood - Wood Selection - Polyester - Metals - Corian - Wood Exclusive - Solid wood ( old grey pinewood excluded). X12 Horizontal or vertical right left - centred 60 Obtained with a special cut out on door thickness. Handle s inner part is painted to match door finish (for polyester> hi gloss / for wood> painted to match door species). Sizes: 120 mm. Compatible cabinets: ogramma STANAR. Compatible finishes: Silcover - Ecolak - Wood - Wood Selection - Polyester - Corian - Wood Exclusive. UNIVERSAL Horizontal centred Obtained with a special cut out on door thickness. 23 SILCOVER ECOLAK POLYESTER CORIAN Handle s inner part is obtained with the following techniques: SILCOVER - ECOLAK > painted door finish. POLYESTER > painted hi gloss to match door colour. CORIAN > solid Corian, white. WOO - WOO SELECTION - WOO EXCLUSIVE > Back panel in wood to match door finish; other handle inner surfaces painted to match door wood species. 30 Sizes: front width -120 mm. 25 Compatible cabinets: ogramma STANAR. 23 Compatible finishes: Silcover - Ecolak - Wood - Wood Selection - Polyester - Corian - Wood Exclusive. WOO WOO SELECTION WOO EXCLUSIVE APRILE Horizontal centred Extruded anodised aluminium, painted or brushed steel Sizes: mm. Handle 360 mm wide cannot be used on doors shorter than 450 mm. / Colours: matt white - matt black - stainless steel. / Compatible cabinets: ogramma STANAR. Compatible finishes: Lasermat - Silcover - Ecolak - Wood - Wood Selection - Polyester - Corian - Wood Exclusive Solid wood. 0.33

34 G e n e r a l t e c h n i c a l i n f o r m a t i o n HANLES WITH EXTRA CHARGE Please add the price increase cod. JZMW01 to each door or front panel, see page ) Please always specify on the order handles position: without info Boffi will consider standard position. 2) When using wide external handles on hinged door, please always check possible opening interferences. 3) With drawers, heavy-duty drawers and pull out, handles position is always centred on the door panel. SERIES AN IMENSIONS STANAR POSITIONING MATERIAL AN COMPATIBILITY 3 25 Handle horizontal ONLY. Made with special cut-out on wider slat (146 mm). Not available with tall unit single door. Compatible finishes: only Wood 3. Compatible cabinets: ogramma STANAR 23 / 20 Left hinged door rawers Pull-out doors Right hinged door 146 X = 146 = X 146 istance X changes always according to direction and width required. No symmetry granted between right and left handles. X3 Handle horizontal ONLY. Made with special cut-out on wider slat (146 mm) Compatible finishes: only Wood 3 and Solid Wood 3. Compatible cabinets: ogramma STANAR 23 / 20 Left hinged door rawers Pull-out doors Right hinged door 146 X = 146 = X 146 istance X changes always according to direction and width required. No symmetry granted between right and left handles. X3L Handle ONLY horizontal. Obtained with a special cut out on door thickness Compatible finishes: only Solid Wood. Not feasible on doors in old grey pinewood. Compatible cabinets: ogramma STANAR 23 Horizontal left Horizontal centred Horizontal right = 146 =

35 = G e n e r a l t e c h n i c a l i n f o r m a t i o n HANLES WITH EXTRA CHARGE Please add the price increase cod. JZMW01 to each door or front panel, see page ) Please always specify on the order handles position: without info Boffi will consider standard position. 2) When using wide external handles on hinged door, please always check possible opening interferences. 3) With drawers, heavy-duty drawers and pull out, handles position is always centred on the door panel. SERIES AN IMENSIONS STANAR POSITIONING MATERIAL AN COMPATIBILITY UEMILAOTTO = 180 / 364 = Position A - Horizontal centred - Width 364 mm only for Silcover, Ecolak, white Polyester, Corian finishes. Obtained with a special cut out on door thickness. Not compatible with tall unit single door. Sizes: mm. 180 / 364 Compatible cabinets: ogramma STANAR. 180 Compatible finishes: SILCOVER / ECOLAK: - Width 180 mm, positions A - B. - Width 364 mm, position A. Position B Horizontal left or right - Only handle W. 180 mm. - Only on hinged door. 180 POLYESTER: Available ONLY in colour white cod.003. It is made with a special solid piece of Corian inserted into the door thickness and then cut out. Therefore the cut out part is always white Corian and different from all the rest of the door (polyester). - Width 180 mm, positions A - B. - Width 364 mm, only position A. WOO / WOO SELECTION / WOO EXCLUSIVE: 180 mm wide available ONLY in Grey-graphite oak, Ash-grey oak, Black Ecowood, Core walnut, Canaletto walnut U.S., smoked oak, Abonos oak. - Width 180 mm, positions A - B. - Width 364 mm, NOT FEASIBLE. CORIAN : - Width 180 mm, positions A - B. - Width 364 mm, only position A. ATTENTION! Not feasible in the finishes or species not indicated here above. YAR / 316 / 466 / 766 / 1066 Horizontal centred = 40 Extruded aluminium. Colours: Stainless steel / matt black / 406 / 556 / 856 / Sizes: mm. NEW 224 / 381/ 531 / 831 / 1131 Horizontal left or right 40 27,5 Examples NOT compatible with hinged door Compatible cabinets: ogramma STANAR. Compatible finishes: Lasermat / Silcover / Ecolak / Wood / Wood Selection / Metals / Polyester / Corian / Solid wood / Wood Exclusive. ATTENTION!!! Compatible ONLY with pull-out or hinged doors (except for the cases here indicated). 0.35

36 G e n e r a l t e c h n i c a l i n f o r m a t i o n CHART FOR HANLES COMPATIBILITY Lasermat Silcover Ecolak Legno Legno Selection Metals Poliestere Corian Legno 3 Legno Exclusive Legno massello Legno massello 3 Handle O O O O O O O O O O T Line O O O O O O O O O O Zone O O O O O O O O O O X12 O O O O O O O Universal O O O O O O O Aprile O O O O O O O O O 3 O X3 O O X3L O 3 uemilaotto O O O 1 O O 2 O Yard O O O O O O O O O O 1 = Only ash-grey oak, grey-graphite oak and black Ecowood. 2 = Only on polyester white 003 (internal part of handle in Corian ). 3 = NOT feasible on doors in old grey pinewood

37 G e n e r a l t e c h n i c a l i n f o r m a t i o n TOPS PROGRAMMA STANAR - SIMPLE - SOHO - FREE ZONE - WOO-IN A - LASERMAT with edge welded with laser technique / Thickness: 20 mm Structure made of wood particle board panel with low formaldehyde emission (class E1), waterproof (class V), plated with nanotechnological paper FENIX NTM. yed edge in polypropylene, welded with laser technique (edge seam hard to be perceived). A Colours: LASERMAT Boffi range. Max. length: 3200 mm. Compatible cabinets: ogramma STANAR - SIMPLE.- FREE ZONE. Attention! Compatible ONLY with TOP-MOUNTE washbasins and BUILT-IN washbasins. B - Glass / Thickness: 12 mm Extra-light tempered glass, painted and frosted. Edges bevelled and satin. B Colours: White - ove-grey - Coffee Max. length: 3650 mm. Compatible cabinets: ogramma STANAR - SIMPLE - SOHO - WOO-IN. Attention! The WOO-IN top is optional: the cabinet with Boffi TOP-MOUNTE washbasins can be installed without any top. C - Glass with integrated moulded washbasin / Thickness: 12 mm Extralight tempered glass, painted and sanded, with 700 x 310 mm moulded integrated washbasin. Edges bevelled and satin. The Extralight glass used on these tops is sandblasted and not frosted. This working process can change the tone of the same colour in frosted version, this shall not be considered cause of complaint. C Colours: White - ove-grey - Coffee Max. L. with central washbasin: 2085 mm. Max. L. with lateral washbasin: 2985 mm (see pages / 16.19). Compatible cabinets: ogramma STANAR - SIMPLE - SOHO. - Cristalplant / Thickness: 15 mm Solid surface made of natural mineral charges (ATH, aluminium tri-hydrate) and low percentage of polyester and pure acrylic polymers. Inert, hypoallergenic and non-toxic. % recyclable, waterproof (class 1), UV-resistant, a compact, nonporous, hygienic and pleasant to touch material. Colours: White. Max. length: 2900 mm. Compatible cabinets: ogramma STANAR - SIMPLE - SOHO - FREE ZONE - WOO-IN. Attention! The WOO-IN top is optional: the cabinet with Boffi TOP-MOUNTE washbasins can be installed without any top. E - Corian / Thickness: 20 mm Non-porous, compact solid surface made of acrylic resin (1/3: polymethylmethacrylate or PMMA) and natural mineral charges (aluminium tri-hydrate (ATH), a by-product of Bauxite process for aluminium extraction). Structure in compounded aluminium. E Colours: White. Max. length: 3650 mm. Compatible cabinets: ogramma STANAR - SIMPLE - FREE ZONE. 0.37

38 G e n e r a l t e c h n i c a l i n f o r m a t i o n TOPS PROGRAMMA STANAR - SIMPLE - SOHO - FREE ZONE - WOO-IN F - Marble - Stone - Granite / Thickness: 20 mm Square-edged top in matt finish, anti-stain and waterproof treated. Solid marble, stone or granite. Option available, with extra charge (see CUSTOMISE SOLUTIONS- PRICE INCREASES- MAINTENANCE chapter), polished finish and, for absolute black Zimbabwe granite only, flamed brushed finish. F Typologies: Carrara white marble - Serena stone - Matraia stone - Cardoso stone - absolute black Zimbabwe granite - quartzite Silver - Black Cosmic granite - Emperador ark marble - Grey Stone marble - quartzite Calacatta. Max. length 2500 mm: Serena stone - Cardoso stone. Max. length 2600 mm: Grey Stone marble. Max. length 2800 mm: Matraia stone - Emperador ark marble. Max. length 2900 mm: quartzite Calacatta. Max. length 3050 mm: Carrara white marble - absolute black Zimbabwe granite - Black Cosmic granite - quartzite Silver. Compatible cabinets: ogramma STANAR - SIMPLE - SOHO - FREE ZONE - WOO-IN. Attention! The WOO-IN top is optional: the cabinet with Boffi TOP-MOUNTE washbasins can be installed without any top. G - Composite Silestone / Thickness: 20 mm Square-edged top in matt finish, with bacteriostatic protection. Composite stone composed of 94% natural quartz and 6% polymer and colouring pigments. Extraordinarily hard and resistant. G Colours: SILESTONE Boffi range. Max. length: 3230 mm (For Yukon white, Kensho grey and Merope grey-brown: 3040 mm). Compatible cabinets: ogramma STANAR - SIMPLE - SOHO - FREE ZONE - WOO-IN. Attention! The WOO-IN top is optional: the cabinet with Boffi TOP-MOUNTE washbasins can be installed without any top. H - Composite ekton / Thickness: 20 mm Square-edged top in matt finish. Material composed of sophisticated blend of raw materials used to produce the very latest in glass and porcelain as well as the highest quality quartz work surfaces. ekton employs exclusive Sinterized Particle Technology, a high tech process which represents an accelerated version of the metamorphic change that natural stone undergoes when subjected to high temperatures and pressure. Electronic microscopy allows us to fully appreciate the material zero porosity and chemical resistance, a consequence of the sinterization and ultra-compaction process exclusive to this material. H Colours: EKTON Boffi range. Max. length: 3200 mm (for Zenith white: 3140 mm). Compatible cabinets: ogramma STANAR - SIMPLE - SOHO - FREE ZONE - WOO-IN. Attention! The WOO-IN top is optional: the cabinet with Boffi TOP-MOUNTE washbasins can be installed without any top. J - Solid wood / Thickness: 23 mm Structure made of panels in poplar multi-layer wood. Surfaces and edges covered by solid wood layers, 5 mm thick, assembled used a 45 folding technique. Finished with matt transparent water-based paints. J Species: LIGHT Canaletto walnut, sawn-effect / Old grey pinewood Max. length: 3000 mm ( old grey pinewood: 2800 mm) Compatible cabinets: ogramma STANAR - SIMPLE - FREE ZONE. NEW 0.38

39 G e n e r a l t e c h n i c a l i n f o r m a t i o n TOPS XILA BATH I - Cristalplant / Thickness: mm Top composed by a 50 mm tall front in same finish as top and 15 mm thick horizontal surface. Solid surface made of natural mineral charges (aluminium tri-hydrate, ATH) and low percentage of polyester and pure acrylic polymers. Inert, hypoallergenic and non-toxic. % recyclable, waterproof (class 1), UV-resistant, a compact, non-porous, hygienic and pleasant to touch material. I Colours: White. Max. length: 2900 mm. L - Marble - Stone - Granite / Thickness: mm Top composed by a 50 mm tall front in same finish as top and 20 mm thick horizontal surface. Solid marble, stone or granite in matt finish, anti-stain and waterproof treated. Option available, with extra charge (see CUSTOMISE SOLUTIONS- PRICE INCREASES- MAINTENANCE chapter), polished finish and, for absolute black Zimbabwe granite only, flamed brushed finish. L M N Typologies: Carrara white marble - Serena stone - Matraia stone - Cardoso stone - absolute black Zimbabwe granite - quartzite Silver - Black Cosmic granite - Emperador ark marble - Grey Stone marble - quartzite Calacatta. Max. length 2500 mm: Serena stone - Cardoso stone. Max. length 2600 mm: Grey Stone marble. Max. length 2800 mm: Matraia stone - Emperador ark marble. Max. length 2900 mm: quartzite Calacatta. Max. length 3050 mm: Carrara white marble - absolute black Zimbabwe granite - Black Cosmic granite - quartzite Silver. M - Composite Silestone / Thickness: 12+50, mm Top composed by a 50 mm tall front in same finish as top and 12/20 mm thick horizontal surface. Matt finish, with bacteriostatic protection. Composite stone composed of 94% natural quartz and 6% polymer and colouring pigments. Extraordinarily hard and resistant Colours: SILESTONE Boffi range. Max. length: 3230 mm (for Yukon white, Kensho grey and Merope grey-brown: 3040 mm). N - Composite ekton / Thickness: 12+50, mm Top composed by a 50 mm tall front in same finish as top and 12/20 mm thick horizontal surface. Matt finish. Material composed of sophisticated blend of raw materials used to produce the very latest in glass and porcelain as well as the highest quality quartz work surfaces. ekton employs exclusive Sinterized Particle Technology, a high tech process which represents an accelerated version of the metamorphic change that natural stone undergoes when subjected to high temperatures and pressure. Electronic microscopy allows us to fully appreciate the material zero porosity and chemical resistance, a consequence of the sinterization and ultra-compaction process exclusive to this material. Colours: EKTON Boffi range. Max. length: 3200 mm (for Zenith white: 3140 mm). 0.39

40 G e n e r a l t e c h n i c a l i n f o r m a t i o n TOPS B14 O - Cristalplant / Thickness: 50 mm The top consists of 15 mm thick sheets with bevelled edges. The lateral bevelled edges should be ordered separately, according to the project. Solid surface made of natural mineral charges (aluminium tri-hydrate, ATH) and low percentage of polyester and pure acrylic polymers. Inert, hypoallergenic and non-toxic. % recyclable, waterproof (class 1), UV-resistant, a compact, non-porous, hygienic and pleasant to touch material. O Colours: White. Max. length: 2900 mm. P - Marble - Stone - Granite / Thickness: 50 mm Top in matt finish, anti-stain and waterproof treated, with bevelled edges. The lateral bevelled edges should be ordered separately, according to the project. The top consists of 20 mm thick sheets and structure In thermosetting polymer polyurethane foam (light, stable over time, waterproof and resistant to thermal shock). Option available - on request -, with extra charge (see chapter CUSTOMISE SOLUTIONS - PRICE INCREASES - MAINTENANCE), polish finish on marble and granite tops and, only for tops in Absolute black Zimbabwe granite, flamed brushed finish. P Q R Typologies: Carrara white marble - Serena stone - Matraia stone - Cardoso stone - absolute black Zimbabwe granite - quartzite Silver - Black Cosmic granite - Emperador ark marble - Grey Stone marble - quartzite Calacatta. Max. length 2500 mm: Serena stone - Cardoso stone. Max. length 2600 mm: Grey Stone marble. Max. length 2800 mm: Matraia stone - Emperador ark marble. Max. length 2900 mm: quartzite Calacatta. Max. length 3050 mm: Carrara white marble - absolute black Zimbabwe granite - Black Cosmic granite - quartzite Silver. Q - Composite Silestone / Thickness: 50 mm Top in matt finish, with bacteriostatic protection, with bevelled edges. The lateral bevelled edges should be ordered separately, according to the project. The top consists of 20 mm thick sheets and structure in thermosetting polymer polyurethane foam (light, stable over time, waterproof and resistant to thermal shock). Material composed of 94% natural quartz and 6% polymer and colouring pigments. Extraordinarily hard and resilient. Colours: SILESTONE Boffi range. Max. length: 3230 mm (for Yukon white, Kensho grey and Merope grey-brown: 3040 mm). R - Composite ekton / Thickness: 50 mm Top in matt finish, with bevelled edges. The lateral bevelled edges should be ordered separately, according to the project. Material composed of sophisticated blend of raw materials used to produce the very latest in glass and porcelain as well as the highest quality quartz work surfaces. ekton employs exclusive Sinterized Particle Technology, a high tech process which represents an accelerated version of the metamorphic change that natural stone undergoes when subjected to high temperatures and pressure. Electronic microscopy allows us to fully appreciate the material zero porosity and chemical resistance, a consequence of the sinterization and ultra-compaction process exclusive to this material. Colours: EKTON Boffi range. Max. length: 3200 mm (for Zenith white: 3140 mm). 0.40

41 G e n e r a l t e c h n i c a l i n f o r m a t i o n TOPS I FIUMI ST S - Cristalplant / Thickness: 20 mm Top with 45 lower bevelled edges on 3 sides perfectly matched with upper 45 edges of I FIUMI ST cabinets. Therefore, the cabinet edges cover the top thickness. Solid surface made of natural mineral charges (aluminium tri-hydrate, ATH) and low percentage of polyester and pure acrylic polymers. Inert, hypoallergenic and non-toxic. % recyclable, waterproof (class 1), UV-resistant, a compact, non-porous, hygienic and pleasant to touch material. S Colours: White. Max. length: 2300 mm. T - Corian / Thickness: 20 mm Top with 45 lower bevelled edges on 3 sides perfectly matched with upper 45 edges of I FIUMI ST cabinets. Therefore, the cabinet edges cover the top thickness. Non-porous, compact solid surface made of acrylic resin (1/3: polymethylmethacrylate or PMMA) and natural mineral charges (aluminium tri-hydrate ATH, a by-product of Bauxite process for aluminium extraction). T Colours: White. Max. length: 3000 mm. U - Marble - Stone - Granite / Thickness: 20 mm Top in matt finish, anti-stain and waterproof treated, with 45 lower bevelled edges on 3 sides perfectly matched with upper 45 edges of I FIUMI ST cabinets. Therefore, the cabinet edges cover the top thickness. Solid marble, stone or granite. Option available - on request -, with extra charge (see chapter CUSTOMISE SOLUTIONS - PRICE INCREASES - MAINTENANCE), polish finish on marble and granite tops and, only for tops in Absolute black Zimbabwe granite, flamed brushed finish. U V W Typologies: Carrara white marble - Serena stone - Matraia stone - Cardoso stone - absolute black Zimbabwe granite - quartzite Silver - Black Cosmic granite - Emperador ark marble - Grey Stone marble - quartzite Calacatta. Max. length 2500 mm: Serena stone - Cardoso stone. Max. length 2600 mm: Grey Stone marble. Max. length 2800 mm: Matraia stone - Emperador ark marble. Max. length 2900 mm: quartzite Calacatta. Max. length 3050 mm: Carrara white marble - absolute black Zimbabwe granite - Black Cosmic granite - quartzite Silver. V - Composite Silestone / Thickness: 20 mm Top in matt finish, with bacteriostatic protection, with 45 lower bevelled edges on 3 sides perfectly matched with upper 45 edges of I FIUMI ST cabinets. Therefore, the cabinet edges cover the top thickness. Solid composite. Material composed of 94% natural quartz and 6% polymer and colouring pigments. Extraordinarily hard and resilient. Colours: SILESTONE Boffi range. Max. length: 3230 mm (for Yukon white, Kensho grey and Merope grey-brown: 3040 mm). W - Composite ekton / Thickness: 20 mm Top in matt finish, with 45 lower bevelled edges on 3 sides perfectly matched with upper 45 edges of I FIUMI ST cabinets. So the cabinet edges cover the top thickness. Solid composite material composed of sophisticated blend of raw materials used to produce the very latest in glass and porcelain as well as the highest quality quartz work surfaces. ekton employs exclusive Sinterized Particle Technology, a high tech process which represents an accelerated version of the metamorphic change that natural stone undergoes when subjected to high temperatures and pressure. Electronic microscopy allows us to fully appreciate the material zero porosity and chemical resistance, a consequence of the sinterization and ultra-compaction process exclusive to this material. Colours: EKTON Boffi range. Max. length: 3200 mm (for Zenith white: 3140 mm). 0.41

42 G e n e r a l t e c h n i c a l i n f o r m a t i o n TOPS WOO-IN FOR GAREN WASHBASIN X - Marble - Stone - Granite / Thickness: 10 mm * Square-edged top in matt finish, anti-stain and waterproof treated. Solid marble, stone or granite. * = Because of technical reasons, the tops for double washbasin are 20 mm thick. X ATTENZIONE!!! - Il piano WOO-IN è opzionale: è possibile allestire il mobile con lavabi SOPRAPIANO da appoggio della gamma Boffi senza l utilizzo del piano. Typologies: Carrara white marble - Cardoso stone - absolute black Zimbabwe granite - quartzite Silver -Emperador ark marble - Grey Stone marble - quartzite Calacatta. Fixed sizes: CUSTOMISATIONS NOT AVAILABLE (see TOPS chapter). Y - Corian, arranged for Garden washbasin installation / Thickness: 12 mm Square-edged top arranged for Garden washbasin installation. Non-porous, compact solid surface made of acrylic resin (1/3: polymethylmethacrylate or PMMA) and natural mineral charges (aluminium tri-hydrate ATH, a by-product of Bauxite process for aluminium extraction). Y ATTENZIONE!!! - Il piano WOO-IN è opzionale: è possibile allestire il mobile con lavabi SOPRAPIANO da appoggio della gamma Boffi senza l utilizzo del piano. Colours: White. Fixed sizes: CUSTOMISATIONS NOT AVAILABLE (see TOPS chapter). 0.42

43 G e n e r a l t e c h n i c a l i n f o r m a t i o n SUSPENE TOPS PIANURA Cristalplant - Corian - Composite SILESTONE - Composite EKTON / Thickness: 70 mm Shelf system for washbasin with back-splash and integrated light. They can be adjacent to back-splash (total depth: 565 mm, back-splash included) or detached from back-splash and provided with LE light behind the countertop (total depth: 595 mm, back-splash included). Top: thickness 70 mm. Back-splash: thickness 65 mm, h. 500 mm, with LE light on the upper part. Upper and side panels in matt white. Please see other technical details on page Cristalplant colours: White. Max. length: 2800 mm. Corian colours: White, ONLY with SABBIA 6 or SABBIA 7 washbasins. Max. length: 3000 mm. Composite typologies: Silestone range - ekton range. Max. length: 2500 mm. FLYER Cristalplant - Corian - Solid wood - Marble, stone, granite, composite / Thickness: mm Suspended top, thickness mm and depth 500 / 600mm, to be fitted with supporting brackets (to be ordered separately). These tops can be fitted with lower covering panel too. Please see other technical details on page Cristalplant colours: White. Max. length: 2700 mm. Corian colours: White, ONLY with SABBIA 6 or SABBIA 7 washbasins. Max. length: 3000 mm. Solid Wood species: natural oak (with knots) / Canaletto LIGHT walnut sawn-effect / old grey pinewood. Max. length: 3000 mm (old grey pinewood: 2800 mm). Marble, stone, granite typologies: Stone / Marble / Granite range. Composite typologies: Silestone range - ekton range. Max. length 2500 mm: Serena stone - Cardoso stone. Max. length 2600 mm: Grey Stone marble. Max. length 2800 mm: Matraia stone - Emperador ark marble. Max. length 2900 mm: quartzite Calacatta. Max. length 3050 mm: Carrara white marble - absolute black Zimbabwe granite - Black Cosmic granite - quartzite Silver. Max. length 3200 mm: EKTON composite (for Zenith white: 3140 mm) Max. length 3230 mm: SILESTONE composite (for Yukon white, Kensho grey and Merope grey-brown: 3040 mm). 0.43

44 G e n e r a l t e c h n i c a l i n f o r m a t i o n MAINTENANCE - USE SPECIFIC PROUCTS - HINTS Boffi suggests the use of the Boffi Clean Set (cod. AVBL029) and of the specific cleaning products indicated on the price list (see page 17.10). As a general advice, if Clean Set Boffi is not available, please do not use products that might scratch, such as abrasive powders and chemicals, solvents or strong acids. Please do not forget that steam and humidity must be considered risk factors for material durability: we recommend wiping always very well all surfaces after cleaning. Any oil stains must be cleaned away immediately. Recommended cleaning agents Harmful cleaning agents ecautions and advice MELAMINE-COATE SURFACES Clean with dry cloth and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. For in-depth cleaning, add a degreaser detergent to water, as Casa 9 Strong Floor egreaser by Nuncas. If these specific products are not available, please use a moist cloth for daily cleaning and a neutral detergent for in-depth cleaning. ry well with soft or microfiber cloth. Abrasive products and products containing chlorine. Attention: o not clean edges using products containing thinners or acetone. SURFACES IN LASERMAT Clean with dry cloth and Multipurpose cleaner by Nuncas, or the specific detergent included in the cleaning kit for Lasermat (cod. AVBL025). For in-depth cleaning, add a degreaser detergent to water, as Casa 9 Strong Floor egreaser by Nuncas. If these specific products are not available, please use a moist cloth for daily cleaning and a neutral detergent for in-depth cleaning. ry well with soft or microfiber cloth. Abrasive detergents, alkaline or products containing chlorine or turpentine. ust spray and furniture wax as these could change the matt finish. Lasermat is highly scratch, steam, water, stain, impact and abrasion resistant. o not wipe with strongly abrasive products. SURFACES IN SILCOVER AN ECOLAK Clean with dry cloth and the Casa 9, Multipurpose cleaner by Nuncas. For in-depth cleaning, add a neutral detergent to water, as Winto Parquet by Nuncas. ry well with soft or microfiber cloth. If these specific products are not available, please use a dry cloth for daily cleaning and a generic window cleaning agent, insisting in case of possible stains. Abrasive detergents and creams. ust spray and furniture wax as these could change the matt finish. When cleaning a new bathroom you may find colour residue on the cloth. This is normal and due to particles of paint that in the drying process rise to the surface. Please remove these particles cleaning the surface with a sponge and a neutral detergent as Winto Parquet by Nuncas. SURFACES IN POLYESTER Clean with dry cloth and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. For indepth cleaning add a neutral detergent to water, as Winto Parquet by Nuncas. ry well with soft or microfiber cloth. If these specific products are not available, please use a dry cloth for daily cleaning and a generic window cleaning agent, insisting in case of possible stains. Abrasive detergents and creams. ust spray and furniture wax as these could stain and leave haloes on surface. If the polyester should dull it is possible to buff the surface with car polish applied using a soft, non-abrasive cloth. 0.44

45 G e n e r a l t e c h n i c a l i n f o r m a t i o n MAINTENANCE - USE SPECIFIC PROUCTS - HINTS Recommended cleaning agents Harmful cleaning agents ecautions and advice SURFACES LACQUERE IN METALS Clean with dry cloth and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. For indepth cleaning, add a neutral detergent to water, as Winto Parquet by Nuncas. ry well with soft or microfibre cloth. If these specific products are not available, please use a dry cloth for daily cleaning and a generic window cleaning agent, insisting in case of possible stains. Abrasive detergents and creams. ust spray and furniture wax as these could stain and leave haloes on surface. Use extreme caution not to scratch the surface. o not use abrasive products. SURFACES IN WOO/ WOO SELECTION / WOO EXCLUSIVE (VENEER) Clean with dry cloth and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. For in-depth cleaning, add a neutral detergent to water, as Winto Parquet by Nuncas. ry well with soft cloth. If these specific products are not available, please use a moist cloth for daily cleaning and a neutral detergent for in-depth cleaning. oducts containing acetone, chlorine or diluents, powders or abrasive products. Strong alkaline detergents. Paints used for wooden surfaces are hydro repellent and anti-yellowing. Avoid scratching and exposure to high temperatures. Remember that wood is a natural product and as such is sensitive to heat and humidity. o not apply furniture waxes. SURFACES IN SOLI WOO (TOPS EXCLUE) Clean with moist cloth. For in-depth cleaning use vegetable soap. ry well with soft cloth. oducts containing acetone, chlorine or diluents, powders or abrasive products. Strong alkaline detergents. Remove immediately any stains for avoiding their permeation. It s recommended to use periodically the specific cleaning / maintenance kit (cod. AVBL023 / AVBL024). TOPS IN SOLI WOO Clean with dry cloth and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. For in-depth cleaning, add a neutral detergent to water, as Winto Parquet by Nuncas. ry well with soft cloth. If these specific products are not available, please use a moist cloth for daily cleaning and a neutral detergent for in-depth cleaning. oducts containing acetone, chlorine or diluents, powders or abrasive products. Strong alkaline detergents. Remove immediately any stains for avoiding their permeation. SURFACES IN MARBLE, GRANITE OR STONE (sandblasted finish matter) Clean daily with a sponge and water+detergent C1.07 AY (cod. AVBL027) or Winto Marmo by Nuncas. For persistent stains use only the detergent (without water). In case of polished finish, it s possible to use Bel Marmo by Nuncas, to protect and maintain the surface brightness. On the surfaces, use periodically the kit of oleo-proofing and waterproof treatment (cod. AVBL028), following the instructions. Metal scrubs, sponges or abrasive products or bleach. In general, avoid all acidic cleaners. In case of fingerprints on matt polished surface, please clean with lukewarm water and dry well. o not use oil-based products or liquid wax or cleaners for other surface typologies. Pls. note: Marble and stone are porous materials, therefore stains penetrate quickly and must be removed immediately; they are particularly sensitive to oil, lemon, vinegar, tea and coffee. 0.45

46 G e n e r a l t e c h n i c a l i n f o r m a t i o n MAINTENANCE - USE SPECIFIC PROUCTS - HINTS Recommended cleaning agents Harmful cleaning agents ecautions and advice SURFACES IN SILESTONE For removing dust and fingerprints, clean with dry cloth and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. To remove grease use Casa 9 Strong egreaser emium by Nuncas with a moist sponge and rinse well. For removing limestone and soap deposits please use Wannet Blu by Nuncas. If these specific products are not available, please use a moist cloth for daily cleaning and a neutral detergent or descaler for in-depth cleaning. Acid or strong alkaline products. etergents containing bleach. Please gently remove stains of materials that harden while drying (i.e. rubber, grease, nail varnish, paints, etc.), with a plastic scraper, after using some lukewarm water. SURFACES IN EKTON For removing dust and fingerprints, clean with dry cloth and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. To remove grease use Casa 9 Strong egreaser emium by Nuncas with a moist sponge and rinse well. For removing limestone and soap deposits please use Wannet Blu by Nuncas. If these specific products are not available, please use a moist cloth for daily cleaning and a neutral detergent or descaler for in-depth cleaning. Acid or strong alkaline products. etergents containing bleach. Please gently remove stains of materials that harden while drying (i.e. rubber, grease, nail varnish, paints, etc.), with a plastic scraper, after using some lukewarm water. SURFACES IN GLASS AN ALUMINIUM For removing dust and fingerprints, clean the aluminium and glass parts with dry cloth and Glasnet by Nuncas. If this specific product is not available, please use a common window cleaning agent, rinsing and drying very well. Scrubs, abrasive detergents and creams. etergents containing acids. Use cotton rags or synthetic cloth intended for cleaning glass in order to avoid leaving fluff on the frosted and pressed glass surfaces. SURFACES IN CRISTALPLANT Clean with dry cloth and a cleaning window agent as Glasnet by Nuncas. For in-depth cleaning, use Brax Cleaner Cream by Nuncas, rinse and dry well. For limestone stains please use Wannet Blu by Nuncas. If these specifi c products are not available, please use a moist cloth and dry well. For persistent stains, consult the maintenance advice supplied with the product. Strong alkaline detergents such as concentrated degreasers. Scrubs and abrasive sponges. For removing persistent stains, please use an abrasive sponge, as Scotch Brite, with gel or abrasive detergents, rinsing well the surface. Please consult the maintenance advice supplied with the product too. SURFACES IN CORIAN Clean with dry cloth and a cleaning window agent as Glasnet by Nuncas. For in-depth cleaning, use Brax Cleaner Cream by Nuncas, rinse and dry well. For limestone stains please use Wannet Blu by Nuncas. If these specific products are not available, please use a moist cloth and dry well. For persistent stains, consult the maintenance advice supplied with the product. Strong alkaline detergents such as concentrated degreasers. Scrubs and abrasive sponges. In case of coloured stains such as wine, coffee or vegetables like aubergines and carrots, please clean the surface with bleach diluted with water (1 part bleach to 2 parts water) - leaving it for some seconds - then rinse well. 0.46

47 G e n e r a l t e c h n i c a l i n f o r m a t i o n MAINTENANCE - USE SPECIFIC PROUCTS - HINTS Recommended cleaning agents Harmful cleaning agents ecautions and advice SURFACES IN PAPERSTONE Clean with moist cloth and warm water and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. If this specific product is not available please use delicate detergent and not abrasive or bleach diluted with water (1 part bleach, 10 parts water). Abrasive detergents or containing bleach. Use extreme caution not to scratch the surface. o not use abrasive products. o not place hot objects on the surfaces. SURFACES IN E CASTELLI METAL Clean with cotton moist cloth and water or specific delicate detergent for painted surfaces. Scrubs and abrasive sponges, solvents, generic or aggressive detergents. In case of stagnant water, please dry well the surface. TAPS, ACCESSORIES AN PARTS IN CHROMIUM-PLATE FINISH Clean with moist cloth and warm water and multipurpose cream (Boffi Clean Set) or the Casa 9, Multipurpose cleaner by Nuncas. If these specific products are not available, please use water and a neutral detergent. Scrubs, detergents and abrasive creams. In general avoid all acidic detergents. Use cotton rags or synthetic cloth to avoid leaving fluff on surfaces. For removing limestone and soap deposits please use Wannet Blu by Nuncas. TAPS, ACCESSORIES AN FINISHE PARTS IN STAINLESS STEEL For removing dust and fingerprints, clean with dry cloth and the Stainless Steel Polish Cleaner by Nuncas. If this specific product is not available, please use a moist cloth and dry with soft cloth or chamois leather, or use a multipurpose cleaner and rinse well. For persistent stains use warm vinegar. Always clean in a motion parallel to the polish markings. To remove limestone and dirt from aerator filters, please remove the aerator and keep it soaking in white vinegar for some hours. Then please wash with water and soap and finally rinse well. Scrubs, abrasive sponges. oducts containing ammonia or hydrochloric acid as these could stain the surface. Use extreme caution not to scratch the surface; do not use sharp objects to remove the protective polythene film. Please remove shortly stains of food weak acids (lemon, tomatoes etc.). Please use Steel otective Cream by Nuncas to remove limestone, ferrous stains and small scratches. TAPS, ACCESSORIES AN FIN- ISHE PARTS IN PV Clean daily with soft cloth and water and neutral detergent. For in-depth cleaning and persistent dirt, please use soft cloth with warm water and vinegar. Rinse well and dray with microfiber cloth. Scrubs, abrasive detergents and creams, abrasive sponges, bleach, ammonia, hydrochloric acid, hydrofluoric acid and derivatives, and all detergents containing acids. Remove immediately any residues left on the surface, especially fluorine-containing toothpastes. HANLES IN ALUMINIUM AN PAINTE ZAMA For removing dust and fingerprints, clean with dry cloth and the Stainless Steel Polish Cleaner by Nuncas. If this specific product is not available, please use a moist cloth and dry with soft cloth or chamois leather, or use a multipurpose cleaner and rinse well. Always clean in a motion parallel to the polish markings. Scrubs, abrasive detergents and creams. etergents containing acids. Avoid scratching as all handles are treated with anti-oxidation paints. CERAMIC WASHBASINS AN SANITARY FIXTURES Clean with a dry cloth and the Glasnet by Nuncas. If this specific product is not available, please use common detergents for sanitary fixtures. Scrubs, abrasive detergents and creams. etergents containing acids. For removing limestone and soap deposits please use Wannet Blu by Nuncas. 0.47

48 G e n e r a l t e c h n i c a l i n f o r m a t i o n MAINTENANCE - USE SPECIFIC PROUCTS - HINTS Recommended cleaning agents Harmful cleaning agents ecautions and advice CERAMILUX - POLISHE For removing most kinds of stains, such as lime or dirt marks, simply clean using a moist cloth or a non-abrasive sponge and multipurpose cream (Boffi Clean Set) or a gel detergent. o not clean with abrasive detergents, abrasive sponges, scrapers, acetone, trichlorethylene, solvents, strong acids (muriatic acid, etc.), or bases (caustic soda, etc.), drain cleaner. Certain substances, e.g. ink, cosmetics or dyes may release colouring agents on the surface, which are therefore to be avoided. o not use the surface as a cutting board. Although Ceramilux is heat-resistant, do not place any burning-hot object, lit cigarettes or pour any boiling fluid on its surface. CERAMILUX - MATT For removing most kinds of stains, such as lime or dirt marks, is recommended to use an abrasive sponge like Scotch Brite with multipurpose cream (Boffi Clean Set) or Brax Cleaner Cream by Nuncas. Finally rinse well. If these specific products are not available, please use soap and water or common detergents (cream or gel), also lightly abrasive. o not clean with abrasive sponges, scrapers, acetone, trichlorethylene, solvents, strong acids (muriatic acid, etc.) or bases (caustic soda, etc.), drain cleaner. o not use scrapers. Certain substances, e.g. ink, cosmetics or dyes may release colouring agents on the surface, which are therefore to be avoided. o not use the surface as a cutting board. Although Ceramilux is heat-resistant, do not place any burning-hot object, lit cigarettes or pour any boiling fluid on its surface. 0.48

49 P r o g r a m m a S T A N A R TECHNICAL FEATURES Suspended, modular base/tall units. The handle use is compulsory. 1 Tops The square-edged tops can be fitted with top-mounted, built-in, under-mounted or moulded flush-mounted washbasins. THICKNESS: mm. EPTH: 500 mm Carcasses It s made of 19 mm thick wood particle board panels, waterproof (class V), with low formaldehyde emission (class E1/CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. SIE PANEL HEIGHT: mm (both compatible with built-in / under-mounted / moulded flush-mounted Boffi washbasins). SIE PANEL EPTH: 470 mm. EPTH INCLUING OOR: 495 mm. MOULE WITH: mm. Finished side panel The visible side panels of all compositions are finished, without an extra charge (please note that front panels in Corian have finished side panels in white Ecolak and front panels in Wood 3 have finished side panels in wood veneer - without 3 effect). The finished side panel includes the finishing of the frontal vertical edge too (Lasermat excluded).the finished side panel IS NOT FEASIBLE in SOLI WOO and 3 SOLI WOO: for these finishes please order the end panels separately. rawers LEGRABOX series with side and back panels in varnished matt black metal. Bottom in black melamine. Front of internal drawers in melamine, same finish as carcass. oors and fronts Finished, thickness 23 mm, with compulsory handle. Handles Each front should have an handle, to be chosen from the range, considering the addition or not of the price increase. 1.3

50 P r o g r a m m a S T A N A R FEASIBLE FINISHES - CABINETS CARCASSES MELAMINE-COATE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) FRONT PANELS FINISH LASERMAT COLOURS / SPECIES 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black SILCOVER White 129 Magnolia 119 Grey 024 Pebble grey 131 Sand 025 Ècru 023 Mud 134 Graphite-grey 118 Black ECOLAK 510 Arctic white 129 Magnolia 513 Cloud colour 024 Pebble grey 512 Oat colour 025 Ècru 023 Mud 515 Basalt grey 517 Charcoal 027 Black WOO 049 Oak 033 Ash-grey oak 076 Grey-graphite oak 331 Larch wood, Aspen white 332 Larch wood, Orion black Black Ecowood POLYESTER 003 White 129 Magnolia 005 Grey RAL Pebble grey 063 Sand 106 Sahara 004 Grey 007 ark green 001 Andalusian red 027 Black METALS 934 Aluminium 194 Magnesium 192 Titanium 191 Lead WOO SELECTION 048 Core walnut 093 Canaletto walnut U.S. 101 Smoked oak CORIAN 173 White WOO Core walnut Black ecowood SOLI WOO 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood SOLI WOO Canaletto LIGHT walnut sawn-effect WOO EXCLUSIVE 077 Abonos oak 1.4

51 P r o g r a m m a S T A N A R FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGIES TOP- MOUNTE BUILT-IN UNER-MOUNTE moulded FLUSH-MOUNTE TOPS FINISH COLOURS / SPECIES WASHBASINS GLASS SANE PAINT- E EXTRALIGHT H 12 mm 818 White 816 ove grey 817 Coffee GLASS FROSTE PAINT- E EXTRALIGHT H 12 mm 818 White 816 ove grey 817 Coffee 1 CRISTALPLANT H 15 mm - White LASERMAT H 20 mm 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black CORIAN H 20 mm 173 White STONE - MARBLE - GRANITE H 20 mm A 240 Marble White Carrara 250 Stone Serena A 200 Stone Cardoso B 245 Stone Matraia B B Granite Quartzite Black absolute Silver Zimbabwe C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E COMPOSITE SILESTONE H 20 mm 432 Expo grey C C 433 Concrete grey 435 Tebas black C 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON H 20 mm E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown SOLI WOO H 23 mm 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood 1.5

52 P r o g r a m m a S T A N A R HANLES Please see the GENERAL TECHNICAL INFORMATION - HANLES section for the choice of the handle size, finish and positioning. STANAR HANLES - No extra charge 1 T LINE Compatible finishes: LASERMAT SILCOVER ECOLAK WOO WOO SELECTION METALS POLYESTER CORIAN WOO 3 WOO EXCLUSIVE SOLI WOO SOLI WOO 3 HANLE Compatible finishes: LASERMAT SILCOVER ECOLAK WOO WOO SELECTION METALS POLYESTER CORIAN WOO 3 WOO EXCLUSIVE SOLI WOO SOLI WOO 3 HANLES WITH PRICE INCREASE - Please add the price increase cod. JZMW01 to each door or front panel ZONE APRILE X12 UNIVERSAL UEMILAOTTO 3 Compatible finishes: Compatible finishes: Compatible finishes: Compatible finishes: Compatible finishes: Compatible finishes: LASERMAT SILCOVER ECOLAK WOO WOO SELECTION METALS POLYESTER CORIAN WOO EXCLUSIVE SOLI WOO SILCOVER ECOLAK WOO WOO SELECTION METALS POLYESTER CORIAN WOO EXCLUSIVE SOLI WOO SILCOVER ECOLAK WOO WOO SELECTION POLYESTER CORIAN WOO EXCLUSIVE SILCOVER ECOLAK WOO WOO SELECTION POLYESTER CORIAN WOO EXCLUSIVE SILCOVER ECOLAK WOO * WOO SELECTION ** POLYESTER *** CORIAN WOO EXCLUSIVE * Only Ash-grey oak, Grey-graphite oak, Black Eco-wood. WOO 3 * * Only Core walnut, Black eco-wood. ** Only Core walnut, Canaletto walnut U.S., Smoked oak. *** White only (internal part of handle in Corian ). X3 X3L YAR Compatible finishes: Compatible finishes: Compatible finishes: WOO 3 SOLI WOO 3 SOLI WOO LASERMAT SILCOVER ECOLAK WOO WOO SELECTION METALS POLYESTER CORIAN WOO EXCLUSIVE SOLI WOO 1.6

53 P r o g r a m m a S T A N A R Technical chart Modules 1 X a a min.288 max Position of water drain - a dimension min.155 max.235 min.288 max.385 = = = = min.155 max.235 min.155 max.235 min.288 max.385 = = = = = = = = = Visible finished side panel = Water drain = Cold water feeder = Warm water feeder X = 280 mm. when top-mounted washbasins are used. 360 mm. when under-mounted und built-in washbasins are used. 1.7

54 P r o g r a m m a S T A N A R TECHNICAL ETAILS Base units for washbasin / / / cassetto opzionale optional drawer tiroir optionnel optionale Schublade cajón opcional Base units and tall units = = etail of fronts H 470 mm = =

55 P r o g r a m m a S T A N A R COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UNER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 SIEL 2 WRCAB01 Sabbia 1 (Solo su / Only on Cristalplant ) WRSBAB01 Sabbia 2 (Solo su / Only on Cristalplant ) WRSBAB02 Kupa (Solo su / Only on Cristalplant ) W2KPAJ001 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WAPTAB02 1 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. Composizione (Composition) 1A Composizione (Composition) 2A Composizione (Composition) 3A Composizione (Composition) 4A Composizione (Composition) 5A Composizione (Composition) 6A Composizione (Composition) 7A Composizione (Composition) 8A Composizione (Composition) 9A Composizione (Composition) 10A Composizione (Composition) 11A Composizione (Composition) 12A Composizione (Composition) 13A Composizione (Composition) 14A Composizione (Composition) 15A Composizione (Composition) 16A Composizione (Composition) 17A Composizione (Composition) 18A Composizione (Composition) 19A Composizione (Composition) 20A Composizione (Composition) 1B Composizione (Composition) 2B Composizione (Composition) 3B Composizione (Composition) 4B Composizione (Composition) 5B Composizione (Composition) 6B Composizione (Composition) 7B Composizione (Composition) 8B Composizione (Composition) 9B Composizione (Composition) 10B Composizione (Composition) 11B Composizione (Composition) 12B Composizione (Composition) 13B Composizione (Composition) 14B Composizione (Composition) 15B 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 55,8 78,2 62,4 72,0 82,8 64,5 231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 1.14

56 P r o g r a m m a S T A N A R COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UNER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 Sidel 2 WRCAB01 Sabbia 1 (Solo su / Only on Cristalplant ) WRSBAB01 Sabbia 2 (Solo su / Only on Cristalplant ) WRSBAB02 Kupa (Solo su / Only on Cristalplant ) W2KPAJ001 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WAPTAB02 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. 1 Composizione (Composition) 16B Composizione (Composition) 17B Composizione (Composition) 18B Composizione (Composition) 19B Composizione (Composition) 20B Composizione (Composition) 21B Composizione (Composition) 22B Composizione (Composition) 23B Composizione (Composition) 24B Composizione (Composition) 25B Composizione (Composition) 26B Composizione (Composition) 27B Composizione (Composition) 28B Composizione (Composition) 29B Composizione (Composition) 30B Composizione (Composition) 31B Composizione (Composition) 32B Composizione (Composition) 33B Composizione (Composition) 34B Composizione (Composition) 35B Composizione (Composition) 36B Composizione (Composition) 37B Composizione (Composition) 38B Composizione (Composition) 39B Composizione (Composition) 40B Composizione (Composition) 41B Composizione (Composition) 42B Composizione (Composition) 43B Composizione (Composition) 44B Composizione (Composition) 45B 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 55,8 78,2 62,4 72,0 82,8 64,5 231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 1.15

57 P r o g r a m m a S I M P L E TECHNICAL FEATURES Suspended, modular base/tall units with push opening system TIP-ON. Units with handle are not feasible. 2 Tops The square-edged tops can be fitted with top-mounted, built-in, under-mounted or moulded flush-mounted washbasins. THICKNESS: mm. EPTH: 500 mm Carcasses It s made of 19 mm thick wood particle board panels, waterproof (class V), with low formaldehyde emission (class E1/CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. SIE PANEL HEIGHT: mm (both compatible with built-in / under-mounted / moulded flush-mounted Boffi washbasins). SIE PANEL EPTH: 470 mm. EPTH INCLUING OOR: 495 mm. MOULE WITH: mm. Finished side panel The visible side panels of all compositions are finished, without an extra charge (please note that front panels in Corian have finished side panels in white Ecolak and front panels in Wood 3 have finished side panels in wood veneer - without 3 effect). The finished side panel includes the finishing of the frontal vertical edge too (Lasermat excluded).the finished side panel IS NOT FEASIBLE in SOLI WOO and 3 SOLI WOO: for these finishes please order the end panels separately. TIP-ON rawers LEGRABOX series with side and back panels in varnished matt black metal. Bottom in black melamine. Front of internal drawers in melamine, same finish as carcass. oors and fronts Thickness 23 mm, with push opening system TIP-ON. 2.3

58 P r o g r a m m a S I M P L E FEASIBLE FINISHES - CABINETS CARCASSES MELAMINE-COATE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) FRONT PANELS FINISH LASERMAT COLOURS / SPECIES 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black SILCOVER 003 White 129 Magnolia 119 Grey 024 Pebble grey 131 Sand 025 Ècru 023 Mud 134 Graphite-grey 118 Black 2 ECOLAK 510 Arctic white 129 Magnolia 513 Cloud colour 024 Pebble grey 512 Oat colour 025 Ècru 023 Mud 515 Basalt grey 517 Charcoal 027 Black WOO 049 Oak 033 Ash-grey oak 076 Grey-graphite oak 331 Larch wood, Aspen white 332 Larch wood, Orion black Black Ecowood POLYESTER 003 White 129 Magnolia 005 Grey RAL Pebble grey 063 Sand 106 Sahara 004 Grey 007 ark green 001 Andalusian red 027 Black METALS 934 Aluminium 194 Magnesium 192 Titanium 191 Lead WOO SELECTION 048 Core walnut 093 Canaletto walnut U.S. 101 Smoked oak CORIAN 173 White WOO Core walnut Black ecowood SOLI WOO 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood SOLI WOO Canaletto LIGHT walnut sawn-effect WOO EXCLUSIVE 077 Abonos oak 2.4

59 P r o g r a m m a S I M P L E FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGIES TOP- MOUNTE BUILT-IN UN- ER-MOUNT- E moulded FLUSH-MOUNTE TOPS FINISH COLOURS / SPECIES WASHBASINS GLASS SANE PAINT- E EXTRALIGHT H 12 mm 818 White 816 ove grey 817 Coffee GLASS FROSTE PAINT- E EXTRALIGHT H 12 mm 818 White 816 ove grey 817 Coffee CRISTALPLANT H 15 mm 2 - White LASERMAT H 20 mm 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black CORIAN H 20 mm 173 White STONE - MARBLE - GRANITE H 20 mm A 240 Marble White Carrara 250 Stone Serena A 200 Stone Cardoso B 245 Stone Matraia B B Granite Quartzite Black absolute Silver Zimbabwe C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E COMPOSITE SILESTONE H 20 mm 432 Expo grey C C 433 Concrete grey 435 Tebas black C 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON H 20 mm E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown SOLI WOO No Match! 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood 2.5

60 P r o g r a m m a S I M P L E Technical chart Modules X min.155 max.235 min.288 max min.288 max.385 = = = = min.155 max.235 min.155 max.235 min.288 max a a Position of water drain - a dimension = = = = = = = = = Visible finished side panel = Water drain = Cold water feeder = Warm water feeder X = 280 mm. when top-mounted washbasins are used. 360 mm. when under-mounted und built-in washbasins are used. 2.6

61 P r o g r a m m a S I M P L E TECHNICAL ETAILS Base units for washbasin / / / cassetto opzionale optional drawer tiroir optionnel optionale Schublade cajón opcional Base units and tall units = = etail of fronts H 470 mm = =

62 P r o g r a m m a S I M P L E COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UNER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 SIEL 2 WRCAB01 Sabbia 1 (Solo su / Only on Cristalplant ) WRSBAB01 Sabbia 2 (Solo su / Only on Cristalplant ) WRSBAB02 Kupa (Solo su / Only on Cristalplant ) W2KPAJ001 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WAPTAB02 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. 2 Composizione (Composition) 1A Composizione (Composition) 2A Composizione (Composition) 3A Composizione (Composition) 4A Composizione (Composition) 5A Composizione (Composition) 6A Composizione (Composition) 7A Composizione (Composition) 8A Composizione (Composition) 9A Composizione (Composition) 10A Composizione (Composition) 11A Composizione (Composition) 12A Composizione (Composition) 13A Composizione (Composition) 14A Composizione (Composition) 15A Composizione (Composition) 16A Composizione (Composition) 17A Composizione (Composition) 18A Composizione (Composition) 19A Composizione (Composition) 20A Composizione (Composition) 1B Composizione (Composition) 2B Composizione (Composition) 3B Composizione (Composition) 4B Composizione (Composition) 5B Composizione (Composition) 6B Composizione (Composition) 7B Composizione (Composition) 8B Composizione (Composition) 9B Composizione (Composition) 10B Composizione (Composition) 11B Composizione (Composition) 12B Composizione (Composition) 13B Composizione (Composition) 14B Composizione (Composition) 15B 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 55,8 78,2 62,4 72,0 82,8 64,5 231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 2.14

63 P r o g r a m m a S I M P L E COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UN- ER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 Sidel 2 WRCAB01 Sabbia 1 (Solo su / Only on Cristalplant ) WRSBAB01 Sabbia 2 (Solo su / Only on Cristalplant ) WRSBAB02 Kupa (Solo su / Only on Cristalplant ) W2KPAJ001 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WAPTAB02 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. Composizione (Composition) 16B Composizione (Composition) 17B Composizione (Composition) 18B Composizione (Composition) 19B Composizione (Composition) 20B Composizione (Composition) 21B Composizione (Composition) 22B Composizione (Composition) 23B Composizione (Composition) 24B Composizione (Composition) 25B Composizione (Composition) 26B Composizione (Composition) 27B Composizione (Composition) 28B Composizione (Composition) 29B Composizione (Composition) 30B Composizione (Composition) 31B Composizione (Composition) 32B Composizione (Composition) 33B Composizione (Composition) 34B Composizione (Composition) 35B Composizione (Composition) 36B Composizione (Composition) 37B Composizione (Composition) 38B Composizione (Composition) 39B Composizione (Composition) 40B Composizione (Composition) 41B Composizione (Composition) 42B Composizione (Composition) 43B Composizione (Composition) 44B Composizione (Composition) 45B 2 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 55,8 78,2 62,4 72,0 82,8 64,5 231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 2.15

64 X I L A B A T H TECHNICAL FEATURES Suspended, modular base units without handle. The tops have a specific recessed finished band on the bottom, which create an handle-rail effect. This detail in combination with the bevelled edge of the doors will offer the grip needed to open the door fronts. 3 Tops The square-edged tops, with finished lower front, can be fitted with top-mounted, built-in, under-mounted or moulded flush-mounted washbasins. THICKNESS: mm (+ lower band H 50 mm) EPTH: 500 mm COMPATIBLE WASHBASINS: top-mounted, built-in, under-mounted and moulded flushmounted (moulded flush-mounted washbasins in Cristalplant on tops in Cristalplant only - moulded flush-mounted washbasins in Corian on tops in Corian only - built-in under-mounted NOT compatible with tops in Lasermat). FINISHES for 12 mm thick tops (+ lower front H 50 mm): Silestone - ekton composite. FINISHES for 15 mm thick tops (+ lower front H 50 mm): Cristalplant. FINISHES for 20 mm thick tops (+ lower front H 50 mm): Corian, stone-marble-granitecomposite (Corian compatible only with top-mounted washbasins in Ceramilux or moulded flush-mounted in Corian ). Carcasses It s made of 19 mm thick wood particle board panels, waterproof (class V), with low formaldehyde emission (class E1/CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. SIE PANEL HEIGHT: mm (both compatible with built-in / under-mounted / moulded flush-mounted Boffi washbasins). HEIGHT INCLUING OOR: mm. SIE PANEL EPTH: 470 mm. EPTH INCLUING OOR: 495 mm. MOULE WITH: mm. rawers LEGRABOX series with side and back panels in varnished matt black metal. Bottom in black melamine. Front of internal drawers in melamine, same finish as carcass. oors and fronts Finished, thickness 23 mm, with upper bevelled edge (on doors in stone / marble / granite the upper profile is in painted aluminium, black or white). 3.3

65 X I L A B A T H FEASIBLE FINISHES - CABINETS CARCASSES MELAMINE-COATE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) FRONT PANELS FINISH SILCOVER COLOURS / SPECIES 003 White 129 Magnolia 119 Grey 024 Pebble grey 131 Sand 025 Ècru 023 Mud 134 Graphite-grey 118 Black ECOLAK 510 Arctic white 129 Magnolia 513 Cloud colour 024 Pebble grey 512 Oat colour 025 Ècru 023 Mud 515 Basalt grey 517 Charcoal 027 Black WOO Oak 033 Ash-grey oak 076 Grey-graphite oak 331 Larch wood, Aspen white 332 Larch wood, Orion black Black Ecowood POLYESTER 003 White 129 Magnolia 005 Grey RAL Pebble grey 063 Sand 106 Sahara 004 Grey 007 ark green 001 Andalusian red 027 Black METALS 934 Aluminium 194 Magnesium 192 Titanium 191 Lead WOO SELECTION 048 Core walnut 093 Canaletto walnut U.S. 101 Smoked oak CORIAN 173 White SOLI WOO 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood WOO EXCLUSIVE 077 Abonos oak STONE - MARBLE - GRANITE A B B C E E 240 Marble White Carrara 200 Stone Cardoso Granite Quartzite Black absolute Silver Zimbabwe 261 Marble Emperador ark 260 Marble Grey Stone 259 Quartzite Calacatta 3.4

66 X I L A B A T H FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGIES 439 Merope greybrown TOP- MOUNTE BUILT-IN UN- ER-MOUNT- E moulded FLUSH-MOUNTE TOPS FINISH COLOURS / SPECIES WASHBASINS CRISTALPLANT H mm - White CORIAN H mm 173 White STONE - MARBLE - GRANITE H mm A 240 Marble White Carrara 250 Stone Serena A 200 Stone Cardoso B 245 Stone Matraia B B Granite Quartzite Black absolute Silver Zimbabwe C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E 3 COMPOSITE SILESTONE H mm 432 Expo grey C C 433 Concrete grey 435 Tebas black C 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 440 oradus black COMPOSITE SILESTONE H mm COMPOSITE EKTON H mm 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white E 456 Irok beige E 451 Strato grey E 457 Ventus grey E 458 Korus grey E E 459 Galema brown COMPOSITE EKTON H mm 3.5

67 X I L A B A T H Technical chart Modules 3 X a a X min.155 max min.288 max.385 = = = = min.288 max.385 min.155 max.235 min.288 max Position of water drain - a dimension min.155 max.235 = = = = = = = = = Visible finished side panel = Water drain = Cold water feeder = Warm water feeder X = 280 mm. when top-mounted washbasins are used. 360 mm. when under-mounted und built-in washbasins are used. 3.6

68 X I L A B A T H COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UN- ER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 Sidel 2 WRCAB01 Sabbia 1 (Solo su / Only on Cristalplant ) WRSBAB01 Sabbia 2 (Solo su / Only on Cristalplant ) WRSBAB02 Kupa (Solo su / Only on Cristalplant ) W2KPAJ001 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WAPTAB02 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. 3 Composizione (Composition) 1A Composizione (Composition) 2A Composizione (Composition) 3A Composizione (Composition) 4A Composizione (Composition) 5A Composizione (Composition) 6A Composizione (Composition) 7A Composizione (Composition) 8A Composizione (Composition) 9A Composizione (Composition) 10A Composizione (Composition) 1B Composizione (Composition) 2B Composizione (Composition) 3B Composizione (Composition) 4B Composizione (Composition) 5B Composizione (Composition) 6B Composizione (Composition) 7B Composizione (Composition) 8B Composizione (Composition) 9B Composizione (Composition) 10B 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 55,8 78,2 62,4 72,0 82,8 64,5 231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 3.14

69 S O H O TECHNICAL FEATURES Suspended, modular base units, fitted with push opening system TIP-ON. Cabinets with handle are not available. Finished end panels, 5 mm thick (glass finish) or 3 mm thick (aluminium finish). 4 Tops The square-edged tops can be fitted with top-mounted, built-in, under-mounted or moulded flush-mounted washbasins. THICKNESS: mm EPTH: 480 mm Carcasses It s made of 19 mm thick wood particle board panels, waterproof (class V), with low formaldehyde emission (class E1/CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. SIE PANEL HEIGHT: mm (both compatible with built-in / under-mounted / moulded flush-mounted Boffi washbasins). SIE PANEL EPTH: 470 mm. EPTH INCLUING OOR: 475 mm. MOULE WITH: mm. rawers TIP-ON LEGRABOX series with side and back panels in varnished matt black metal. Bottom in black melamine. Front of internal drawers in melamine, same finish as carcass. oors and fronts Finished, thickness 5 mm (glass) or 3 mm (aluminium), with push opening system TIP-ON. Support made of 16 mm thick wood particle board panels, black, waterproof (class V), with low formaldehyde emission (class E1/CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. 4.3

70 S O H O FEASIBLE FINISHES - CABINETS CARCASSES MELAMINE-COATE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) FRONT PANELS FINISH GLASS FROSTE PAINTE EXTRALIGHT COLOURS / SPECIES 818 White 816 ove grey 817 Coffee ALUMINIUM 382 Steel 381 ark 4 S O H O FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGIES TOP- MOUNTE BUILT-IN UNER-MOUNTE moulded FLUSH-MOUNTE TOPS FINISH COLOURS / SPECIES WASHBASINS GLASS SANE PAINT- E EXTRALIGHT H 12 mm 818 White 816 ove grey 817 Coffee GLASS FROSTE PAINT- E EXTRALIGHT H 12 mm 818 White 816 ove grey 817 Coffee CRISTALPLANT H 15 mm - White STONE - MARBLE - GRANITE H 20 mm A 240 Marble White Carrara 250 Stone Serena A 200 Stone Cardoso B 245 Stone Matraia B B Granite Quartzite Black absolute Silver Zimbabwe C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E COMPOSITE SILESTONE H 20 mm 432 Expo grey C C 433 Concrete grey 435 Tebas black C 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON H 20 mm E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 4.4

71 S O H O Technical chart Modules X a a min.155 max Position of water drain - a dimension min.288 max.385 = = = = min.155 max.235 min.288 max.385 = = = = = end panel in glass = Water drain = Cold water feeder = Warm water feeder X = 280 mm. when top-mounted washbasins are used. 360 mm. when under-mounted und built-in washbasins are used. 4.5

72 S O H O COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UN- ER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Complete compositions: WASHBASIN CUT-OUT price is included. Compositions designed by Customer: A THE WASHBASIN CUT- OUT (see Customised Solutions chapter). Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 A45 Compact WRAQAE02 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 Sidel 2 WRCAB01 Sabbia 1 (Solo su / Only on Cristalplant ) WRSBAB01 Sabbia 2 (Solo su / Only on Cristalplant ) WRSBAB02 Kupa (Solo su / Only on Cristalplant ) W2KPAJ001 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WAPTAB02 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. 4 Composizione (Composition) 1A / 1B Composizione (Composition) 2A / 2B Composizione (Composition) 3A / 3B Composizione (Composition) 4A / 4B Composizione (Composition) 5A / 5B Composizione (Composition) 6A / 6B Composizione (Composition) 7A / 7B Composizione (Composition) 8A / 8B Composizione (Composition) 9A / 9B Composizione (Composition) 10A / 10B Composizione (Composition) 11A / 11B Composizione (Composition) 12A / 12B Composizione (Composition) 13A / 13B Composizione (Composition) 14A / 14B Composizione (Composition) 15A / 15B Composizione (Composition) 16A / 16B Composizione (Composition) 17A / 17B Composizione (Composition) 18A / 18B Composizione (Composition) 19A / 19B Composizione (Composition) 20A / 20B Composizione (Composition) 21A / 21B Composizione (Composition) 22A / 22B Composizione (Composition) 23A / 23B Composizione (Composition) 24A / 24B Composizione (Composition) 25A / 25B Composizione (Composition) 26A / 26B Composizione (Composition) 27A / 27B Composizione (Composition) 28A / 28B Composizione (Composition) 29A / 29B Composizione (Composition) 30A / 30B Composizione (Composition) 31A / 31B Composizione (Composition) 32A / 32B Composizione (Composition) 33A / 33B Composizione (Composition) 34A / 34B Composizione (Composition) 35A / 35B 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 86,2 74,3 55,8 78,2 62,4 72,0 82,8 64,5 231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 4.10

73 B 1 4 TECHNICAL FEATURES Suspended, modular base units, available for central and end use. The units haven t an handle and are equipped with under top handle-rail. The door opening is allowed by the upper bevelled-edge door matched with the handle-rail and the bevelled-edge top. 5 Tops The tops have visible bevelled edges, on one or more sides, according to the project. THICKNESS: 50 mm EPTH: 505 mm Under top handle-rail In painted aluminium, placed between top and door, along all bevelled-edge top sides. FINISHES: white - black. Carcasses It s made of 19 mm thick wood particle board panels, waterproof (class V), with low formaldehyde emission (class E1/CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. SIE PANEL HEIGHT: mm (both compatible with built-in / under-mounted / moulded flush-mounted Boffi washbasins). SIE PANEL EPTH: 470 mm. EPTH INCLUING OOR: 495 mm. MOULE WITH: mm. rawers LEGRABOX series with side and back panels in varnished matt black metal. Bottom in black melamine. Front of internal drawers in melamine, same finish as carcass. oors and fronts Finished, thickness 23 mm, with upper bevelled edge (door type BN). On end base units and end panels the vertical lateral edges are bevelled too. 5.3

74 B 1 4 FEASIBLE FINISHES - CABINETS CARCASSES MELAMINE-COATE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) FRONT PANELS FINISH SILCOVER COLOURS / SPECIES 003 White 129 Magnolia 119 Grey 024 Pebble grey 131 Sand 025 Ècru 023 Mud 134 Graphite-grey 118 Black ECOLAK 510 Arctic white 129 Magnolia 513 Cloud colour 024 Pebble grey 512 Oat colour 025 Ècru 023 Mud 515 Basalt grey 517 Charcoal 027 Black WOO 049 Oak 033 Ash-grey oak 076 Grey-graphite oak 331 Larch wood, Aspen white 332 Larch wood, Orion black Black Ecowood POLYESTER White 129 Magnolia 005 Grey RAL Pebble grey 063 Sand 106 Sahara 004 Grey 007 ark green 001 Andalusian red 027 Black METALS 934 Aluminium 194 Magnesium 192 Titanium 191 Lead WOO SELECTION 048 Core walnut 093 Canaletto walnut U.S. 101 Smoked oak CORIAN 173 White SOLI WOO 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood WOO EXCLUSIVE 077 Abonos oak 5.4

75 B 1 4 FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGIES 439 Merope greybrown TOP- MOUNTE BUILT-IN UNER-MOUNTE moulded FLUSH-MOUNTE TOPS FINISH COLOURS / SPECIES WASHBASINS CRISTALPLANT H 50 mm - White STONE - MARBLE - GRANITE H 50 mm A 240 Marble White Carrara 250 Stone Serena A 200 Stone Cardoso B 245 Stone Matraia B B Granite Quartzite Black absolute Silver Zimbabwe C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E COMPOSITE SILESTONE H 50 mm 432 Expo grey C C 433 Concrete grey 435 Tebas black C 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 440 oradus black COMPOSITE EKTON H 50 mm E E E E E E Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 5.5

76 B 1 4 Technical chart Modules a a min.288 max.385 min.155 max.235 min.288 max.385 Position of water drain - a dimension = = = = min.155 max.235 min.155 max.235 min.288 max.385 = = = = = = = = = Visible finished side panel = Water drain = Cold water feeder = Warm water feeder 5.6

77 B 1 4 TECHNICAL ETAILS FRONTALI BASI USO TERMINALE OORS FOR EN-USE BASE UNITS PORTES E BASES À EMPLOI TERMINAL TÜREN FÜR ENSTÜCK UNTERSCHRÄNKE PUERTAS POR MUEBLES BAJOS CON USO FINAL S

78 B 1 4 TECHNICAL ETAILS ,5 4 H. 300 / Standard base unit H. 300/635 mm. 2. end base unit with shelf, right door X. 3. end panel left SX, th. 23 mm. with bevelled edge. 4. Aluminium handle-rail, white or black painted In case of base unit with shelf and end hinged door, the door hinge has to be positioned always on the side opposite to the bevelled one Section of the top with aluminium handle-rail Worktop 505 mm deep. 2. Aluminium handle-rail (white or black) 3. Base unit in 19 mm. thick melamine-coated mm. thick finished door ,5 The under top aluminium handle-rail is thought to be placed on the upper perimeter of composition base units and consists of a longitudinal bar, whose length is the sum of the base units +3 mm.; and of two bars W. 471,5 mm. The bars are appropriately bevelled, so as to guarantee a complete continuity of the handle-rail on the composition perimeter. The top width is always the sum of the base units +35 mm. for each side with bevelled edge. The depth is always 505 mm The top must be compulsorily purchased by Boffi as it characterizes composition function and image. In case of orders without top a price increase - fixed amount for each linear top metre - is applied, see page

79 B 1 4 COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UN- ER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 Sidel 2 WRCAB01 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WAPTAB02 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout 5 Composizione (Composition) 1A Composizione (Composition) 2A Composizione (Composition) 3A Composizione (Composition) 4A Composizione (Composition) 5A Composizione (Composition) 6A Composizione (Composition) 7A Composizione (Composition) 8A Composizione (Composition) 9A Composizione (Composition) 10A Composizione (Composition) 11A Composizione (Composition) 12A Composizione (Composition) 13A Composizione (Composition) 14A Composizione (Composition) 15A Composizione (Composition) 16A Composizione (Composition) 17A Composizione (Composition) 18A Composizione (Composition) 1B Composizione (Composition) 2B Composizione (Composition) 3B Composizione (Composition) 4B Composizione (Composition) 5B Composizione (Composition) 6B Composizione (Composition) 7B Composizione (Composition) 8B Composizione (Composition) 9B Composizione (Composition) 10B Composizione (Composition) 11B Composizione (Composition) 12B Composizione (Composition) 13B Composizione (Composition) 14B Composizione (Composition) 15B Composizione (Composition) 16B Composizione (Composition) 17B Composizione (Composition) 18B 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 55,8 78,2 62,4231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 5.16

80 I F I U M I S T TECHNICAL FEATURES Suspended, modular base units without handle. The 45 angled sections of front and end panels houses the top, which has 45 edges on 3 sides (the cabinet edges cover the top thickness). The drawer can be opened through the lower side of the front. Base units can be suspended or floor-mounted. Cabinets with handle are not available. 6 Tops Tops have 45 edges on 3 sides, to match upper edges of front and end panels in finish, in order to make the top thickness not visible. THICKNESS: 20 mm EPTH: 531 mm COMPATIBLE WASHBASINS: top-mounted, built-in, under-mounted and moulded flush-mounted. Carcasses Made of in the same finish as front panels. SILCOVER: MF medium density fibres, 19 mm thick, matt fine textured lacquered. WOO: made of 19 mm thick MF medium density fibres board, veneered with 0,6 mm thick wood veneer; 1 mm thick wood edge. SIE PANEL HEIGHT: 400 mm (compatible with top-mounted, built-in, under-mounted and moulded flush-mounted washbasins). SIE PANEL EPTH: 530 mm. EPTH INCLUING OOR: 530 mm. MOULE WITH: mm. rawers LEGRABOX series with side and back panels in varnished matt black metal. Bottom in black melamine. Front of internal drawers in same finish as carcass. oors and fronts Thickness 19 mm in MF medium density wood particle panels, matt lacquered, fine textured (SILCOVER) or veneered with 0,6 mm thick wood veneer, with 1 mm thick wood edge (WOO). 45 edges on all sides. The drawer can be opened through the lower side of the front. 6.3

81 I F I U M I S T FEASIBLE FINISHES - CABINETS FRONT PANELS AN CARCASS FINISH SILCOVER COLOURS / SPECIES 003 White 129 Magnolia 119 Grey 024 Pebble grey 131 Sand 025 Ècru 023 Mud 134 Graphite-grey 118 Black WOO 049 Oak 033 Ash-grey oak 076 Grey-graphite oak WOO SELECTION 048 Core walnut 093 Canaletto walnut U.S. 101 Smoked oak 6 I F I U M I S T FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGIES Black Ecowood TOP- MOUNTE BUILT-IN UNER-MOUNTE moulded FLUSH-MOUNTE TOPS FINISH COLOURS / SPECIES WASHBASINS CRISTALPLANT H 20 mm - White CORIAN H 20 mm 173 White STONE - MARBLE - GRANITE H 20 mm A 240 Marble White Carrara 250 Stone Serena A 200 Stone Cardoso B 245 Stone Matraia B B Granite Quartzite Black absolute Silver Zimbabwe C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E COMPOSITE SILESTONE H 20 mm 432 Expo grey C C 433 Concrete grey 435 Tebas black C 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON H 20 mm E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 6.4

82 I F I U M I S T Technical chart BASE UNITS FOR WASHBASIN MONOBLOC UNIT FOR WASHBASIN 420 a a X 19 X min.110 max X = 350 mm. when top-mounted washbasins are used. 480 mm. when built-in and under-mounted washbasins are used. (middle height to washbasin upper part = 900 mm) X X min.310 max.440 = Water drain = Cold water feeder = Warm water feeder = = = = Position of water drain - a dimension BASE UNITS WITH HEAVY-UTY RAWER AN INTERNAL RAWER OPEN-FACE BASE UNITS WITH RAWER Composition example 6.5

83 F R E E Z O N E TECHNICAL FEATURES Suspended, modular units without handle. The doors are gripped (and opened) through the specific handle-rail, mounted on the upper part of the cabinet. Three different door opening methods: HINGE / PULL-OUT / COPLANAR SLIING. 7 Tops The square-edged tops can be fitted with top-mounted, built-in, under-mounted or moulded flush-mounted washbasins. THICKNESS: mm EPTH: 500 mm Carcasses It s made of 19 mm thick wood particle board panels, waterproof (class V), with low formaldehyde emission (class E1/CARB P2), treated with high performance melamine resin. Front and back edges in ABS, same colour. SIE PANEL HEIGHT: mm (both compatible with built-in / under-mounted / moulded flush-mounted Boffi washbasins). SIE PANEL EPTH: 470 mm. EPTH INCLUING OOR: 495 mm. HINGE/PULL-OUT MOULE WITH: mm. COLPANAR SLIING MOULE WITH: mm. Handle-rail (compulsory) In painted aluminium. Colour: white / black. Covering for handle-rail (OPTIONAL) Finished. The thickness changes accordingly to finish. To be glued or glued to the aluminium handle rail. THICKNESS: max 20 mm rawers LEGRABOX series with side and back panels in varnished matt black metal. Bottom in black melamine. Front of internal drawers in same finish as carcass. oors and fronts (All finishes excluded: GLASS / ALUMINIUM / E CASTELLI A-B / STONE A-B-C--E) Finished, thickness 23 mm. oors and fronts GLASS / ALUMINIUM / E CASTELLI A-B / STONE A-B-C--E Finished front panel mounted on AMX frame in black anodised aluminium. Thickness mm (nominal). 7.3

84 F R E E Z O N E FEASIBLE FINISHES - CABINETS CARCASSES MELA- MINE-COATE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) FRONT PANELS FINISH LASERMAT COLOURS / SPECIES 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black SILCOVER 003 White 129 Magnolia 119 Grey 024 Pebble grey 131 Sand 025 Ècru 023 Mud 134 Graphite-grey 118 Black ECOLAK 510 Arctic white 129 Magnolia 513 Cloud colour 024 Pebble grey 512 Oat colour 025 Ècru 023 Mud 515 Basalt grey 517 Charcoal 027 Black WOO 049 Oak 033 Ash-grey oak 076 Grey-graphite oak 331 Larch wood, Aspen white 332 Larch wood, Orion black Black Ecowood 7 POLYESTER 003 White 129 Magnolia 005 Grey RAL Pebble grey 063 Sand 106 Sahara 004 Grey 007 ark green 001 Andalusian red 027 Black METALS 934 Aluminium 194 Magnesium 192 Titanium 191 Lead WOO SELECTION 048 Core walnut 093 Canaletto walnut U.S. 101 Smoked oak CORIAN 173 White WOO Core walnut Black ecowood GLASS 818 Frosted painted Extralight White 816 Frosted painted Extralight ove grey 817 Frosted painted Extralight Coffee SOLI WOO 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood SOLI WOO Canaletto LIGHT walnut sawn-effect 7.4

85 F R E E Z O N E FEASIBLE FINISHES - CABINETS CARCASSES MELA- MINE-COATE 130 Silk white 608 Grey-graphite oak (openpore effect) 606 Elm wood (open-pore effect) FRONT PANELS FINISH WOO EXCLUSIVE COLOURS / SPECIES 077 Abonos oak ALUMINIUM 382 Steel 381 ark E CASTELLI METALS A A B B B B 353 élabré iron B 354 Striped Maistral stainless steel élabré brass 356 Striped delabrè brass 351 élabré copper 352 Orbitale délabré cop STONE - MARBLE - GRANITE A B B C E E 240 Marble White Carrara 200 Stone Cardoso Granite Quartzite Black absolute Silver Zimbabwe 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone 259 Quartzite Calacatta 7 7.5

86 F R E E Z O N E FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGY TOP- MOUNTE BUILT-IN UNER-MOUNTE moulded FLUSH-MOUNTE TOPS FINISH CRISTALPLANT H 15 mm COLOURS / SPECIES - White LASERMAT H 20 mm 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black CORIAN H 20 mm 173 White 7 STONE - MARBLE - GRANITE H 20 mm COMPOSITE SILESTONE H 20 mm A 240 Marble White Carrara 432 Expo grey C 250 Stone Serena A C 433 Concrete grey 200 Stone Cardoso 435 Tebas black B C 245 Stone Matraia 431 Zeus white B B Granite Quartzite Black absolute Silver Zimbabwe 437 Lagoon white 436 Yukon white C 261 Marble Emperador ark 438 Kensho grey 254 Granite Black Cosmic 434 Unsui brown 260 Marble Grey Stone E 439 Merope greybrown 259 Quartzite Calacatta E 440 oradus black COMPOSITE EKTON H 20 mm 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white E 456 Irok beige E 451 Strato grey E 457 Ventus grey E 458 Korus grey E E 459 Galema brown SOLI WOO H 23 mm 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood 7.6

87 F R E E Z O N E Technical chart Base unit modules with pull-out fronts and hinged doors X a a = = min.155 max.235 min.288 max.385 = = min.288 max.385 min.155 max.235 min.288 max X Position of water drain - a dimension min.155 max.235 = = = = = = = = = Visible finished side panel = Water drain = Cold water feeder = Warm water feeder X = 280 mm. when top-mounted washbasins are used. 360 mm. when under-mounted und built-in washbasins are used. 7.7

88 F R E E Z O N E Technical chart Base unit modules with coplanar doors 470 X a a a X Position of water drain - a dimension min.155 max.235 min.288 max.385 = = = = = Visible finished side panel = Water drain = Cold water feeder = Warm water feeder X = 280 mm. when top-mounted washbasins are used. 360 mm. when under-mounted und built-in washbasins are used. 7.8

89 F R E E Z O N E TECHNICAL ETAILS BASE UNITS FWITH PULL-OUT FRONTS Base units 500 Base unit for washbasin with shaped drawer Base unit for washbasin with single front and double drawer (1 shaped) SECTION A-A' SECTION B-B' A B A B SECTION C-C' 1200 SECTION -' 500 C C BASE UNITS WITH HINGE OORS Base units Base unit for washbasin with hinged door / / / cassetto opzionale optional drawer tiroir optionnel optionale Schublade cajón opcional 7.9

90 F R E E Z O N E TECHNICAL ETAILS BASE UNITS WITH COPLANAR SLIING OORS Base units SECTION A-A' 1200 SECTION B-B' 500 A B A B C C E F SECTION C-C' SECTION -' SECTION E-E' SECTION E-E' E F HANLE-RAIL * For technical reasons the thickness of the handle rail covering (optional) varies according to the FINISH. The maximum thickness is 20 mm, to allow for the opening of the door front. 7.10

91 F R E E Z O N E COMPOSITIONS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins BUILT-IN washbasins - UN- ER-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Universal piccolo (small) WRUNAB03 Universal grande (big) WRUNAB02 Sidel 2 WRCAB01 Sabbia 1 (Solo su / Only on Cristalplant ) WRSBAB01 Sabbia 2 (Solo su / Only on Cristalplant ) WRSBAB02 Kupa (Solo su / Only on Cristalplant ) W2KPAJ001 Pietra piccolo (small) WAPTAB01 Pietra grande (big) WAPTAB02 Sabbia BTM WRSBAF01 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. 7 Composizione (Composition) 1A Composizione (Composition) 2A Composizione (Composition) 3A Composizione (Composition) 4A Composizione (Composition) 5A Composizione (Composition) 6A Composizione (Composition) 7A Composizione (Composition) 8A Composizione (Composition) 9A Composizione (Composition) 10A Composizione (Composition) 1B Composizione (Composition) 2B Composizione (Composition) 3B Composizione (Composition) 4B Composizione (Composition) 5B Composizione (Composition) 6B Composizione (Composition) 7B Composizione (Composition) 8B Composizione (Composition) 9B Composizione (Composition) 10B Composizione (Composition) 1C Composizione (Composition) 2C Composizione (Composition) 3C Composizione (Composition) 4C Composizione (Composition) 5C 219,3223,5 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 55,8 78,2 62,4 72,0 82,8 64,5 231,5235,8 70,0 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 7.22

92 W O O - I N TECHNICAL FEATURES Type A: front panels assembled "WITHOUT FINGER JOINT TECHNIQUE", with LEGRABOX drawers. Finished suspended monobloc base units, with drawers and open-faced compartments. rawers with finished front panels, push opening system TIP-ON. Cabinets with handle are not available. 8 Top (optional) The monobloc WOO-IN base units can be equipped with top-mounted washbasins installed directly on them. Alternatively is possible to use the OPTIONAL square-edged top with reduced depth 480 mm. 2 top typologies are available: 1) Fixed sized top for GAREN washbasin, available in 10/12/20 mm thickness (including the specific cut-outs for GAREN washbasin). Please see TOPS chapter, WOO-IN section for GAREN washbasin. 2) Top, per linear metre, for top-mounted washbasins, available in 12/15/20 mm thickness. Please see TOPS chapter, SOHO - WOO-IN section. THICKNESS: mm. EPTH: 480 mm Carcasses Available in the following finishes: LASERMAT: made of wood particle board panel with low formaldehyde emission (class E1 / CARB P2), waterproof (class V), plated withnanotechnological paper (FENIX NTM ). Edge in polypropylene, welded with laser technique. WOO / WOO SELECTION / WOO EXCLUSIVE: wood particle board panel, waterproof (class V), with low formaldehyde emission (classe1 / CARB P2) or in MF medium density fibres board, veneered with 0,6 mm. thick veneer wood. HEIGHT: 490 mm. EPTH: 500 mm WITH: mm. rawers TIP-ON LEGRABOX series with side and back panels in varnished matt black metal. Bottom and front (of internal drawers) in black melamine. Without handle, with push opening system TIP-ON. rawer front panels in LASERMAT / WOO / WOO SELECTION / WOO EXCLUSIVE (horizontal grain). 8.3

93 W O O - I N TECHNICAL FEATURES Type B: front panels assembled "WITH FINGER JOINT TECHNIQUE", with WOO drawers. Suspended monobloc base units totally in wood, with drawers and open-faced compartments. Exclusive drawers assembled with finger joint technique and push opening system TIP-ON. Cabinets with handle are not available. 8 Top (optional) The monobloc WOO-IN base units can be equipped with top-mounted washbasins installed directly on them. Alternatively is possible to use the OPTIONAL square-edged top with reduced depth 480 mm. 2 top typologies are available: 1) Fixed sized top for GAREN washbasin, available in 10/12/20 mm thickness (including the specific cut-outs for GAREN washbasin). Please see TOPS chapter, WOO-IN section for GAREN washbasin. 2) Top, per linear metre, for top-mounted washbasins, available in 12/15/20 mm thickness. Please see TOPS chapter, SOHO - WOO-IN section. THICKNESS: mm. EPTH: 480 mm Carcasses Totally made of 22 mm thick multi-layer wood panels, veneered with very thick wood veneer, with wood edge. Visible perimeter edge. HEIGHT: 490 mm. EPTH: 500 mm WITH: mm. rawers TIP-ON rawers made of 16 mm thick multi-layer wood structure, veneered with very thick sheets,edges in wood. Push opening system TIP-ON. rawer front panels with horizontal grain. Front panels and sides assembled with finger joint technique. 8.4

94 W O O - I N FEASIBLE FINISHES - CABINETS WITH FRONT PANELS ASSEMBLE WITHOUT FINGER JOINT TECHNIQUE (Type A) WASHBASIN TYPOLOGIES LEGRABOX drawers, black coloured. The top-mounted washbasins of the Boffi range can be mounted on the monobloc units (without top). TOP- MOUNTE FRONT PANELS AN CARCASS FINISH COLOURS / SPECIES WASHBASINS LASERMAT 177 Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black WOO 049 Oak 033 Ash-grey oak 076 Grey-graphite oak 331 Larch wood, Aspen white 332 Larch wood, Orion black Black Ecowood WOO SELECTION 048 Core walnut 093 Canaletto walnut U.S. 101 Smoked oak WOO EXCLUSIVE 077 Abonos oak 8 W O O - I N FEASIBLE FINISHES - CABINETS WITH FRONT PANELS ASSEMBLE WITH FINGER JOINT TECHNIQUE (Type B) WASHBASIN TYPOLOGIES WOO drawers assembled with finger joint technique. The top-mounted washbasins of the Boffi range can be mounted on the monobloc units (without top). TOP- MOUNTE FRONT PANELS AN CARCASS FINISH COLOURS / SPECIES WASHBASINS WOO ASSEMBLE WITH FINGER JOINT TECHNIQUE * 092 Oak with knots WOO ASSEMBLE WITH FINGER JOINT TECHNIQUE 093 Canaletto walnut U.S. WOO ASSEMBLE WITH FINGER JOINT TECHNIQUE 077 Abonos oak * ATTENTION!!! - Exclusive species for WOO-IN only. 8.5

95 W O O - I N FEASIBLE FINISHES - TOPS FOR GAREN WASHBASIN WASHBASIN TYPOLOGIES The top-mounted washbasins of the Boffi range can be mounted on the monobloc units (without top). ATTENTION!!! - OPTIONAL top, arranged for GAREN washbasin only. TOP-MOUNTE GAREN TOPS FINISH COLOURS / SPECIES WASHBASINS STONE - MARBLE - GRANITE H 10 mm CORIAN H 12 mm * A 240 Marble White Carrara 173 White 200 Stone Cardoso B 257 Quartzite Silver C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E * Because of technical reasons, the top in Stone / Marble / Granite with double washbasin is 20 mm thick and not 10 mm. 8 W O O - I N FEASIBLE FINISHES - TOPS WASHBASIN TYPOLOGIES The top-mounted washbasins of the Boffi range can be mounted on the monobloc units (without top). ATTENZIONE!!! - OPTIONAL top. TOP- MOUNTE TOPS FINISH COLOURS / SPECIES WASHBASINS GLASS FROSTE PAINT- E EXTRALIGHT H 12 mm 818 White 816 ove grey 817 Coffee CRISTALPLANT H 15 mm - White STONE - MARBLE - GRANITE H 20 mm A 240 Marble White Carrara 250 Stone Serena A 200 Stone Cardoso B 245 Stone Matraia B B Granite Quartzite Black absolute Silver Zimbabwe C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E COMPOSITE SILESTONE H 20 mm 432 Expo grey C C 433 Concrete grey 435 Tebas black C 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON H 20 mm 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white E 456 Irok beige E 451 Strato grey E 457 Ventus grey E 458 Korus grey E E 459 Galema brown 8.6

96 W O O - I N TECHNICAL ETAILS Position of water drain 490 X a X a X a min.155 max Position of water drain - a dimension = = = Visible finished side panel = Water drain = Cold water feeder = Warm water feeder X = 280 mm. when top-mounted washbasins are used. 360 mm. when under-mounted und built-in washbasins are used. 8.7

97 W O O - I N Technical chart CABINETS WITH FRONT PANELS ASSEMBLE WITHOUT FINGER JOINT TECHNIQUE (Type A) L 905 mm 861 BWANZ090WS L 1188 mm BWAMQ120WS L 1205 mm 1161 BWAMS120WS BWAMT120WS BWANZ120WS L 1488 mm BWAMU150WS BWAMT150WS L 1788 mm BWAMQ180WS BWAMT180WS BWAMT180WS BWAMU180WS BWAMR180WS CABINETS WITH FRONT PANELS ASSEMBLE WITH FINGER JOINT TECHNIQUE (Type B) L 905 mm 861 BWANZ090WS L 1188 mm BWAMQ120W L 1205 mm 1161 BWAMS120W BWAMT120W BWANZ120W L 1488 mm BWAMU150W BWAMT150W L 1788 mm BWAMQ180W BWAMS180W BWAMT180W BWAMU180W BWAMR180W 8.8

98 W O O - I N TECHNICAL ETAILS - CABINETS WITH FRONT PANELS ASSEMBLE WITHOUT FINGER JOINT TECHNIQUE (Type A) 8 - Monobloc base unit for washbasin with 4 drawers (1 shaped upper drawer) BWAMQ180WS S SECTION E-E' SECTION F-F' E F 490 G G 8 E F rawers compatible with OMESTICI / ONA accessories: please use P 372 mm deep accessories. H H SECTION G-G' SECTION H-H' 8.9

99 W O O - I N TECHNICAL ETAILS - CABINETS WITH FRONT PANELS ASSEMBLE WITH FINGER JOINT TECHNIQUE (Type B) 8 - Monobloc base unit for washbasin with 4 drawers (1 shaped upper drawer) BWAMQ180W S SECTION A-A' SECTION B-B' A B C C A B SECTION C-C' rawers compatible with OMESTICI / ONA accessories: please use P 372 mm deep accessories SECTION -' 8.10

100 8 W O O - I N MONOBLOC BASE UNITS 8.11

101 W O O - I N MONOBLOC BASE UNITS - COMPATIBLE WASHBASINS TOP-MOUNTE washbasins Please choose ONLY compatible washbasins. The washbasin position is centred according to the middle part of the under-washbasin unit. If the taps are mounted on the top, please add the tap cut-outs. The indicated compatibility is referred to spouts with or without integrated mixer. Garden WBGAAE01 Gobi 1 WRGBAE01 Gobi 2 WRGBAE02 Sabbia 3 WRSBAC01 Fisher Island WRAFAE01 Iceland WRICAE01 Cathino 3 WXCHAE02 - WXCHAE04 Cathino 1 WXCHAE01 - WXCHAE03 Adda Corian WNAAE01 A45 Compact WRAQAE02 A45 / A45 STONE WRAQAE01 - WMAQAE01 Lotus WRLSAE01 Compatible with wall-mounted spout / top-mounted spout positioned behind or laterally Compatible with wall-mounted spout or top-mounted spout positioned laterally Compatible with wall-mounted spout Compatible with wall-mounted spout or top-mounted spout positioned behind. 8 Base (Base unit) n. 1 Base (Base unit) n. 2 Base (Base unit) n. 3 Base (Base unit) n. 4 Base (Base unit) n. 5 Base (Base unit) n. 6 Base (Base unit) n. 7 Base (Base unit) n. 8 Base (Base unit) n. 9 Base (Base unit) n. 10 Base (Base unit) n. 11 Base (Base unit) n. 12 * 70,1 117,2 84,2 54,4 87,1 52,4 43,9 142,1 86,2 98,0 74,3 * The price of the GAREN washbasin changes according to the finish of the internal bottom cover: please see "Washbasins" chapter. 8.12

102 U E C TECHNICAL FEATURES Modular system composed of open-faced units and washbasin elements. The system doesn t require a top, because each element is totally finished. Open-faced unit Totally made of white Corian or black PaperStone. HEIGHT: 300 mm. EPTH: 438 mm. WITH, EN USE: mm. WITH, MILE USE: mm. Washbasin element Totally made of white Corian, without overflow. HEIGHT: 300 mm. EPTH: 450 mm. WITH, EN USE: 600 mm. WITH, MILE USE: 688 mm

103 U E C TECHNICAL ETAILS PAPERSTONE : black, thickness 10 mm. CORIAN : white, thickness 11 mm / / Any tap holes are feasible ONLY in the positions indicated min 310 max 370 = = Water drain Cold water feeder Warm water feeder 9.4

104 U P P E R TECHNICAL FEATURES Modular system composed of open-faced units, which can be mounted on wall (also suspended) or on top. If the Upper units are mounted on the top, a specific finished basement is supplied. ATTENTION!! - NOT COMPATIBLE WITH B14 COMPOSITIONS. UNIT FINISHES SILCOVER: complete range. ECOLAK: complete range. WOO: Oak, grey graphite oak, Ash grey oak, Black Ecowood ONLY. WOO SELECTION: complete range. LEGNO EXCLUSIVE: Abonos Oak ONLY. PAPERSTONE : black. BASEMENT FINISHES (between top and units) 10 LASERMAT: complete range. PAPERSTONE : black. CRISTALPLANT : white. CORIAN : white. STONE, MARBLE, GRANITE, COMPOSITE: complete range 10.3

105 U P P E R Technical chart OPEN-FACE UNITS OPEN-FACE UNITS WITH COMPARTMENT FOR SOCKETS

106 U P P E R NOTE TO ESIGNER CALCULATION OF THE UNIT HEIGHT, LATERAL USE LATERAL USE WITH BASE UNITS H1 H2 H H3 400 LEGEN: H1 = base unit height H2 = top thickness H3 = 20 mm (thickness of Upper basement) H = Upper unit height, LATERAL USE = H1 + H2 + H HEIGHTS H1: ogramma STANAR / ogramma SIMPLE / SOHO / FREE ZONE = 300 / 470 mm XILA BATH = 350 / 520 mm (unit + front panel) FIUMI ST = 420 mm WOO-IN = 490 mm UEC = 300 mm 10.5

107 U P P E R NOTE TO ESIGNER CALCULATION OF THE UNIT AN FINISHE BASEMENT LENGTH SINGLE USE L L1 L2 LP L = L2 + LP L1 = L - 40 EN USE WITH FINISHE SIE PANEL L L1 L2 L = L2 L1 = L - 20 EN USE WITH PANEL L 20 L1 L2 LP L = L2 + LP L1 = L - 20 LEGEN: L = unit length L1 = basement length L2 = base unit length LP = panel thickness 10.6

108 M o n o b l o c u n i t s B15 - (esign Norbert Wangen ) 50 Silcover Ecolak Wood Polyester / Metals / Wood Selection Corian Wood Exclusive / Solid wood Washbasin top and one side panel in marble. Base unit for washbasin with finished side panel and finished drawer front panels. On the order please specify the handle-rail colour: white or black. LEGRABOX drawers, compatible with P 372 mm deep OMESTICI / ONA accessories. Washbasin without overflow, with chromium-plated siphon and waste drain and marble plug. Please order separately the tap holes, if necessary. rawn=right (), mirrored=left (S) White Carrara marble WMNWMB03 S- Black Marquinia marble WMNWMB04 S- Silcover Ecolak Wood Polyester / Metals / Wood Selection Wood Exclusive / Solid wood 11 B15C - (esign Norbert Wangen ) Washbasin top and one side panel in Cristalplant. Base unit for washbasin with finished side panel and finished drawer front panels. AVAILABLE VERSION WITH SIE PANEL POSITIONE ON RIGHT ONLY. On the order please specify the handle-rail colour: white or black. LEGRABOX drawers, compatible with P 372 mm deep OMESTICI / ONA accessories. Washbasin without overflow, with chromium-plated siphon, white waste drain and plug. Please order separately the tap holes, if necessary ,5 67, WRNWMB

109 M o n o b l o c u n i t s Silcover QUATWO - (esign Jeffrey Bernett ) Y / /360 Base unit for washbasin in Silcover, colours of Boffi range. Top in white Cristalplant, visible thickness: 5 mm (total thickness: 15 mm). Integrated washbasin: Universal small WRUNAB03. LEGRABOX drawers. Opening of the lateral drawer: grabbing the lower part of the drawer front panel. Opening of the under-washbasin drawer: push opening system TIP-ON. Please order separately the tap holes, if necessary. Y = 900 mm (suggested). rawn=right (), mirrored=left (S). Compatible siphon (to be ordered separately): ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. Compatible waste drain (to be ordered separately): ANBN001 chromium-plated / ANHG001 + ANR002 stainless steel WRQTMB01 S

110 C o m p l e m e n t a r y f u r n i t u r e ogramma TREVES TECHNICAL FEATURES (esign Piero Lissoni ) Open-faced wall units, with door or frame door + mirror. Push opening system TIP-ON. Carcasses oduced with 14 mm thick wood particle boards, waterproof (class V), with low formaldehyde emission (class E1), treated with high performance melamine resin. Assembled using the 45 folding technique. FINISHES: external part and frontal trim in matt white, internal part and shelves in thermo-treated larch wood, textured finish. oors Made of 14 mm thick woody ultra light panel, with push opening system TIP-ON. FINISHES: Silcover. Frame doors In aluminium, th. 14 mm, with mirrored glass. Push opening system TIP-ON. FINISHES: black anodised aluminium

111 C o m p l e m e n t a r y f u r n i t u r e ogramma TREVES Technical chart (esign Piero Lissoni ) OPEN-FACE (Horizontal assembly too) WITH OOR WITH FRAME OOR + MIRROR 12.4

112 C o m p l e m e n t a r y f u r n i t u r e ogramma TREVES (esign Piero Lissoni ) Open-faced wall unit - L 300 mm Horizontal or vertical assembly possible. Melamine-coated shelves. CUSTOMISATIONS ARE NOT AVAILABLE PKIBK030N PBIBK030N PRIBK030N PKKBK030N PBKBK030N PRKBK030N Wall unit with hinged door - L 300 mm oor in Silcover. Without handle, with push opening system TIP-ON. uring assembly it s possible to choose right or left opening. Melamine-coated shelves. CUSTOMISATIONS ARE NOT AVAILABLE PKJCR030N PBJCR030N PRJCR030N PKLCR030N PBLCR030N PRLCR030N Wall unit with frame door - L 300 mm Frame door in black anodised aluminium with mirror. Without handle, with push opening system TIP-ON. uring assembly it s possible to choose right or left opening. Melamine-coated shelves. CUSTOMISATIONS ARE NOT AVAILABLE PKJCT030N PBJCT030N PRJCT030N PKLCT030N PBLCT030N PRLCT030N 12.5

113 C o m p l e m e n t a r y f u r n i t u r e GLASS Technical chart (esign Piero Lissoni ) A B How to position dowels (Wall hole Ø 10 mm.) A B L H

114 C o m p l e m e n t a r y f u r n i t u r e GLASS (esign Piero Lissoni ) Open-faced wall units in transparent tempered glass. Back panel in painted glass: white, grey, black, red, mirror. Open-faced wall unit - 1 compartment CUSTOMISATIONS ARE NOT AVAILABLE. On the order please specify the back panel colour: white, grey, black, red, mirror PLCMA040N Open-faced wall unit - 2 compartments CUSTOMISATIONS ARE NOT AVAILABLE. On the order please specify the back panel colour: white, grey, black, red, mirror PLCMA080N Open-faced wall unit - 2 compartments CUSTOMISATIONS ARE NOT AVAILABLE. On the order please specify the back panel colour: white, grey, black, red, mirror PPCMA020N Open-faced wall unit - 4 compartments CUSTOMISATIONS ARE NOT AVAILABLE. On the order please specify the back panel colour: white, grey, black, red, mirror PECMA020N 12.7

115 C o m p l e m e n t a r y f u r n i t u r e GLASS (esign Piero Lissoni ) Open-faced wall units in transparent tempered glass. Back panel in painted glass: white, grey, black, red, mirror. Open-faced wall unit - 6 compartments CUSTOMISATIONS ARE NOT AVAILABLE. On the order please specify the back panel colour: white, grey, black, red, mirror PJCMA020N

116 C o m p l e m e n t a r y f u r n i t u r e FLYER units (esign C.R.S. Boffi ) External parts of carcass are in finish. 16 mm thick door with push opening system TIP-ON. Silcover Wood Wood Selection Silcover, front in solid wood Suspended base unit with drawer + internal drawer 8 8 Melamine-coated internal part of carcass. LEGRABOX drawers. rawers compatible with OMESTICI / ONA accessories: please use P 372 mm deep accessories. CUSTOMISATIONS ARE NOT AVAILABLE. Wood / Wood Selection / Solid wood: horizontal grain. Internal drawer front panel in black melamine. ABONOS OAK: upon request the cabinet can be finished in Silcover with front panel in Abonos Oak solid wood. To price this option please consider the cost of the drawer unit in Silcover with front panel in solid wood +30% BNCPU060FL BNCPU090FL BNCPZ060FL BNCPZ090FL

117 C o m p l e m e n t a r y f u r n i t u r e PIANURA units (esign Monica Armani ) Finished units with 70 mm thick door, with push opening system TIP-ON SILCOVER: all range colours. WOO: Oak, grey graphite oak, Ash grey oak ONLY. WOO SELECTION: Core walnut ONLY, Canaletto walnut U.S. and smoked Oak. LEGNO EXCLUSIVE: Abonos Oak. Silcover Wood Wood Selection Wood Exclusive Suspended tall unit with shelves and hinged door oor with mirror on internal side. 6 shelves in black anodised aluminium, fitted with black anti-slip mat. CUSTOMISATIONS ARE NOT AVAILABLE CBBS035S S- 135,4 191,3 219,0 Suspended base unit with drawer + internal drawer LEGRABOX drawers. rawers compatible with OMESTICI / ONA accessories: please use P 372 mm deep accessories. CUSTOMISATIONS ARE NOT AVAILABLE BPBPQ070S 94,8 183,2 209,7 Additional internal shelf For PIANURA tall unit. Black anodised aluminium, fitted with black anti-slip mat ACCE

118 C o m p l e m e n t a r y f u r n i t u r e OTHELLO (esign Nendo ) Wall unit 3 compartments in white Corian, 6 mm thick. 2 doors with two sides, 4 mm thick mirror (A) / white Corian (B). 180 opening. CUSTOMISATIONS ARE NOT AVAILABLE. A B A A B B B A PKMK090N

119 C o m p l e m e n t a r y f u r n i t u r e ZONE wall units Compulsory handle. Mirror finish: the handle is integrated in the aluminium frame. The socket cut-out under the wall unit has to be ordered separately (please see Customised solutions chapter). Lasermat / Silcover Ecolak Wood Polyester / Metals / Wood Selection Mirror Wood Exclusive Wall unit - H 600 mm 2 melamine-coated shelves. 230 L PBMMB120N PBMMB150N PBMMB180N PBMMB210N PBMMB240N Wall unit - H 900 mm 1 fixed shelf + 2 melamine-coated shelves. 230 L PRMMB120N PRMMB150N PRMMB180N PRMMB210N PRMMB240N Wall unit - H 1200 mm 1 fixed shelf + 2 melamine-coated shelves. 230 L PJMMB120N PJMMB150N PJMMB180N PJMMB210N PJMMB240N 12.12

120 A c c e s s o r i e s f o r c a b i n e t s INTERNAL RAWERS LEGRABOX internal drawer. - H 105 mm. Compatible ONLY with ogramma STANAR, SIMPLE tall units with hinged doors. Bottom and back side in black melamine. Lateral sides in black metal. Melamine-coated front panel in same finish as carcass. For L P 345 mm tall unit AAX041 For L P 345 mm tall unit AAX042 For L P 345 mm tall unit AAX043 LEGRABOX internal drawer. - H 105 mm. Compatible ONLY with ogramma STANAR, SIMPLE, FREE ZONE, B14 base units with hinged doors. Bottom and back side in black melamine. Lateral sides in black metal. Melamine-coated front panel in same finish as carcass. Compatible internal accessories: P 372 mm (L 300 drawer excluded). For L P 495 mm base unit AAX021 For L P 495 mm base unit AAX022 For L P 495 mm base unit AAX023 LEGRABOX internal drawer. - H 105 mm. For compartment of under-washbasin base unit. Compatible ONLY with ogramma STANAR, SIMPLE and FREE ZONE base units for washbasin with hinged doors. Bottom and back side in black melamine. Lateral sides in black metal with upper small bar. Melamine-coated front panel in same finish as carcass. Please order one drawer each compartment. 13 For L 261 mm compartment (L 900 mm base unit) AAX061 For L 411 mm compartment (L 1200 mm base unit) AAX062 LEGRABOX internal drawer. - H 190 mm. For compartment of under-washbasin base unit. Compatible ONLY with B14 under-washbasin base units with hinged doors. Bottom and back side in black melamine. Lateral sides in black metal with upper small bar. Melamine-coated front panel in same finish as carcass. Please order one drawer each compartment. For L 261 mm compartment (L 900 mm base unit) AAX026 For L 411 mm compartment (L 1200 mm base unit) AAX

121 A c c e s s o r i e s f o r c a b i n e t s COVERING PLATES - VARIOUS ACCESSORIES Covering plate. Aluminium. To be ordered when the siphon connection cut-out on the unit is not used AVMT

122 A c c e s s o r i e s f o r c a b i n e t s FOR INTERNAL SPACE OF RAWERS - OMESTICI series Accessories in black-dyed ash wood, for LEGRABOX / WOO-IN drawers (not compatible with aluminium drawers). For base units P 475 / 495 / 500 / 530 / 594. IMPORTANT : the OMESTICI accessories are laid inside the drawer. Each drawer can accommodate accessory compositions to obtain the maximum width L, indicated in the Technical chart of inside useful sizes. L Technical chart of inside useful sizes LEGRABOX drawers/heavy-duty drawers (internal too). L=366 L=516 L=816 L= L=366 L=516 L=816 L= L=520 L=820 L=1120 L=520 L=820 L= Technical chart of inside useful sizes WOO-IN drawers

123 A c c e s s o r i e s f o r c a b i n e t s FOR INTERNAL SPACE OF RAWERS - OMESTICI series Accessories in black-dyed ash wood, for LEGRABOX / WOO-IN drawers (not compatible with aluminium drawers). For base units P 475 / 495 / 500 / 530 / 594. OMESTICI - ivider. * For drawer of L 450/600 mm base units. * = internal compartment compatible with accessories A-B-C AAHI005 OMESTICI - ivider with compartment for eye liner. For drawer of L 450/600 mm base units AAHJ007 OMESTICI - ivider with compartment for nail varnishes. For drawer of L 450/600 mm base units AAHJ008 OMESTICI - ividers with compartments. For drawer of L 450/600 mm base units AAHK003 OMESTICI - ivider. * * * For drawer of L 900/1200 mm base units. Not compatible with drawer of under-washbasin base units. * = internal compartment compatible with accessories A-B-C AAHI

124 A c c e s s o r i e s f o r c a b i n e t s FOR INTERNAL SPACE OF RAWERS - OMESTICI series Accessories in black-dyed ash wood, for LEGRABOX / WOO-IN drawers (not compatible with aluminium drawers). For base units P 475 / 495 / 500 / 530 / 594. OMESTICI - Equipped divider. For drawer of L 900/1200 mm base units. Not compatible with drawer of under-washbasin base units AAHJ009 OMESTICI - A - Box with cover. To be laid inside AAHL001 OMESTICI - B - Box with cover. To be laid inside heavy-duty drawers only AAHL OMESTICI - C - Box with cover and internal division. To be laid inside heavy-duty drawers only AAHL003 OMESTICI - - Holder for hairdryer. To be laid inside heavy-duty drawers only AAHM

125 A c c e s s o r i e s f o r c a b i n e t s FOR INTERNAL SPACE OF RAWERS - OMESTICI series Accessories in black-dyed ash wood, for LEGRABOX / WOO-IN drawers (not compatible with aluminium drawers). For base units P 475 / 495 / 500 / 530 / 594. OMESTICI - F - Box with Kleenex tissue-holder. To be laid inside AAHM002 OMESTICI - G - Box for medicines. To be laid inside AAHL

126 A c c e s s o r i e s f o r c a b i n e t s FOR INTERNAL SPACE OF RAWERS - ONA series Accessories in plastic, matt finish, for LEGRABOX / WOO-IN drawers (not compatible with aluminium drawers). For base units P 475 / 495 / 500 / 530 / 594. Colour: grey. IMPORTANT : the ONA accessories are laid inside the drawer. Each drawer can accommodate accessory compositions to obtain the maximum width L, indicated in the Technical chart of inside useful sizes. Technical chart of inside useful sizes LEGRABOX drawers/heavy-duty drawers (internal too). L=366 L=516 L=816 L= L=366 L=516 L=816 L= L=520 L=820 L=1120 L=520 L=820 L= Technical chart of inside useful sizes WOO-IN drawers

127 A c c e s s o r i e s f o r c a b i n e t s FOR INTERNAL SPACE OF RAWERS - ONA series Accessories in plastic, matt finish, for LEGRABOX / WOO-IN drawers (not compatible with aluminium drawers). For base units P 475 / 495 / 500 / 530 / 594. Colour: grey. ONA - Accessories set - A. It includes: tray with 3 removable small boxes with lid + grid that can be equipped with cosmetic holder + Kleenex tissue holder. H max 90 mm L L = min 412 mm / max 482 mm AAHS003 ONA - Accessories set - B. It includes: tray with 3 removable small boxes with lid + grid that can be equipped with cosmetic holder. H max 69 mm L L = min 288 mm / max 378 mm AAHS004 ONA - Side storage tray - C. It includes: 3 removable small boxes with lid AAHU002 ONA - Side storage tray -. 2 compartments AAHU

128 P a n e l s ice per square metre. The price of surfaces smaller than 0,1 m², is fixed and it s the same as the price of 0,1 m² surface (EXCEPT MELAMINE-COATE PANELS: minimum 0,5 m²). Melamine MELAMINE-COATE panel. max 1200 H min 50 mm, max 1200 mm. L min 50 mm, max 2780 mm (Elm wood 2730 mm). Order minimal surface for single panel: 0,5 m². max ice per square metre SBAXNN15 FINISHE panel. H min 50 mm, max 1200 mm. L min 50 mm, max 3000 mm. max 1200 max ice per square metre SBAYNT03 14 Panel in CORIAN. H min 50 mm, max 1200 mm. L min 50 mm, max 3000 mm. max 1200 Corian Lasermat Silcover Ecolak Metals / Polyester max ice per square metre SAARNN

129 P a n e l s ice per square metre. The price of surfaces smaller than 0,1 m², is fixed and it s the same as the price of 0,1 m² surface (EXCEPT MELAMINE-COATE PANELS: minimum 0,5 m²). Wood Wood Selection Panel in veneer WOO. H min 50 mm, max 2900 mm. L min 50 mm, max 1200 mm. max ice per square metre SBACBA03 Panel in veneer WOO 3. Plank-effect, alternating thickness 20 and 23 mm. H min 50 mm, max 2750 mm. L min 50 mm, max 1260 mm. max 2750 Wood 3 max 2900 Wood Exclusive max ice per square metre SBACBC04 14 Panel in SOLI WOO (23 mm thick). H min 50 mm, max 2420 mm. L min 50 mm, max 1260 mm. max 2420 Solid wood max For surfaces from 0,1 a 0,3 m² - ice per square metre SBAFBA04 For surfaces from 0,3 a 0,6 m² - ice per square metre SBAFBA05 For surfaces more than 0,6 m² - ice per square metre SBAFBA

130 P a n e l s ice per square metre. The price of surfaces smaller than 0,1 m², is fixed and it s the same as the price of 0,1 m² surface (EXCEPT MELAMINE-COATE PANELS: minimum 0,5 m²). Solid wood 3 Panel in SOLI WOO 3 (20 / 23 mm thick). Planks, alternating thickness 20 and 23 mm. H min 50 mm, max 2420 mm. L min 50 mm, max 1260 mm. max 2420 max For surfaces from 0,1 a 0,3 m² - ice per square metre SBAFBA07 For surfaces from 0,3 a 0,6 m² - ice per square metre SBAFBA08 For surfaces more than 0,6 m² - ice per square metre SBAFBA

131 B a c k p a n e l s ice per square metre. The price of surfaces smaller than 0,1 m², is fixed and it s the same as the price of 0,1 m² surface. Wood Wood Selection Back panel in veneer WOO. Vertical grain. Arranged for wall fixing. H min 181 mm, max 2900 mm. L min 300 mm, max 1200 mm ice per square metre SIACBA03 Glass Wood Exclusive Back panel in GLASS. Aluminium frame, stainless steel, white or black finish. H min 180 mm, max 1200 mm. L min 300 mm, max 2400 mm , ice per square metre SIBHNN02 14 Stone A Stone B Stone C Stone Stone E Back panel in STONE, MARBLE, GRANITE, COMPOSITE. H Please see the price categories and dimensional limits on THE GENERAL TECHNICAL PART (INFO). Polished finish is available upon request, with a price increase. See chapter CUSTOMISE SOLUTIONS. H min 180 mm. L min 350 mm. L 20 ice per square metre SPBENN

132 B a c k - s p l a s h e s ice per linear metre. Cristalplant Back-splash in CRISTALPLANT. H min 50 mm, max 180 mm. L min 50 mm, max 2900 mm ice per linear metre SOBXNN01 Back-splash in CORIAN. H min 50 mm, max 180 mm. L min 50 mm, max 3650 mm ice per linear metre SOARNN02 14 Stone A Stone B Stone C Stone Stone E Corian 19 Back-splash in STONE, MARBLE, GRANITE, COMPOSITE. H H min 50 mm, max 180 mm. L min 350 mm. L 19 ice per linear metre SOBENN

133 S h e l v e s ice per linear metre. Each shelf should be equipped with the specific supporting hardware cod. AMFE004 / AMFE005. Please check always the feasibility of shelves that exceed the size limits indicated in the price list. Costs and delivery times are evaluated and communicated each time, in relation to individual case. Lasermat Silcover Ecolak Wood Polyester / Metals / Wood Selection 14 Corian Wood Exclusive / Solid wood Shelf IN SAME FINISH AS OORS / TOPS / 60 Lasermat Legno massello Solid wood L max 2700 mm. LASERMAT > Laser welded edge. H 60 mm: made of honeycomb board (Solid wood excluded). H 60 mm: not available for back panels. The old solid pinewood can be, over time, altered (cracks and possible retractions of the same slats due to temperature and humidity change), result of possible wood natural change caused by time. The above mentioned characteristics shall not be considered cause of complaint. 40 Altre finiture Other finishing 60 Altre finiture Other finishing Thickness: 40 mm ice per linear metre MAETB5 ice per linear metre MAEVB5 ice per linear metre MAEZB5 ice per linear metre MAEBB5 Thickness: 60 mm ice per linear metre MAFTB5 ice per linear metre MAFVB5 ice per linear metre MAFZB5 ice per linear metre MAFBB5 Shelf in CORIAN. Made of honeycomb board. L max 3650 mm. H 60 mm: not available for back panels. ice per linear metre MRETB5 ice per linear metre MREVB5 ice per linear metre MREZB5 ice per linear metre MREBB5 ice per linear metre MRFTB5 ice per linear metre MRFVB5 ice per linear metre MRFZB5 ice per linear metre MRFBB5 14.8

134 S h e l v e s Accessories Pair of concealed pins for shelf support Ø 12 mm. Cut-out included AMFE004 Pair of concealed pins for shelf support Ø 14 mm. To be used on wood walls. Cut-out included AMFE

135 S u s p e n d e d t o p s PIANURA (esign Monica Armani ) TECHNICAL FEATURES / Technical chart Wall-mounted shelf system for washbasin with back-splash and integrated light. All shelf systems have a specific wall fixing structure. Top and back-splash are always in the same finish. Tops: 70 mm thick. They can be adjacent to back-splash (total depth: 565 mm, back-splash included) or detached from back-splash and provided with LE light behind the countertop (total depth: 595 mm, back-splash included). Please add the specific holes for washbasin and tap integration. Finish: Stone C / / E (only Silestone or ekton composite) and white Cristalplant (washbasin and tap are to be ordered separately). / white Corian (SAB- BIA 6-7 moulded flush-mounted washbasin included, tap to be ordered separately). Back-splash: 65 mm thick, h. 500 mm, provided with LE light on upper part. Upper cover panel and side panels in matt white. Please add the specific hole for possible taps. Finish: Stone C / / E (only Silestone or ekton composite), white Cristalplant, white Corian. ESIGN INSTRUCTIONS: Please see the compatibility chart for the choice of washbasin (for tops in Cristalplant or Stone C / / E) and tap. Washbasin, tap, warm/cold water feeders and cables are to be installed referring to Pianura technical sheet. The use of taps by customer should before checked and authorized by Boffi and is allowed only for recessed types ontops together with Boffi spouts cod. RINS23/24/25/26/27/28/29/30 (tap on top /spout on back-splash). On the order please always specify the hole diameter. Adjacent top etached top with light COMPATIBILITY WASHBASINS/TAPS Washbasin, tap, warm/cold water feeders and cables are to be installed referring to Pianura technical sheet. WASHBASINS TAPS 15 MINIMAL ECPLISE a b LIQUI WINGS PIPE GAREN a b a b a b TOP-MOUNTE WRAFE01 - Fisher Island WRICAE01 - Iceland WXCHAE01/3 - Cathino 1 Ceramilux WXCHAE02/4 - Cathino 3 Ceramilux WRGBAE01 - Gobi 1 WRGBAE02 - Gobi 2 WRSBAC01 - Sabbia 3 MINIMAL mixer tap cod. REM08 ECLIPSE mixer tap cod. RERX05/15 O O O O Mixer tap cod. RESL10 Spout RINS27/28 O O O Mixer tap cod. RHNS05/06 Spout RINS23/24/25/26 O O PIPE mixer cod. REFP01 Spout RINS23/25/29/30 O O O Spout RINS23/25/29/30 O Mixer with spout cod. RHNS01/02 O GAREN mixer tap cod. REGN01 O UNER-MOUNT- E, MOULE FLUSH-MOUNT- E WRUNAB03 - Universal, small WRUNAB02 - Universal, big WRCAB01 - Sidel 2 ZTRBK01 - Sabbia 6 ZTRBK02 - Sabbia 7 a = mounted on top b = mounted on back-splash 15.3

136 S u s p e n d e d t o p s PIANURA (esign Monica Armani ) ATTENTION!!! - Stone C / / E categories are feasible in Silestone or ekton composite ONLY. Tops with width below the minimum specified are not feasible. Stone C Stone Stone E Top adjacent to back-splash in COMPOSITE - P 565 mm With under-mounted UNIVERSAL SMALL washbasin, L = min 850 mm. With under-mounted UNIVERSAL BIG washbasin, L = min 1 mm. The extension for hoses connection kit, cod. RRNS05/06, is suggested in case of compositions with top-mounted taps. 500 L 565 L from 700 to 0 mm - Unit price URAS01 L from 1 to 1500 mm. - Unit price URAS02 L from 1501 to 2000 mm - Unit price URAS03 L from 2001 to 2500 mm - Unit price URAS04 Top detached from back-splash in COMPOSITE - P 595 mm Rear LE light. With under-mounted UNIVERSAL SMALL washbasin, L = min 850 mm. With under-mounted UNIVERSAL BIG washbasin, L = min 1 mm. The extension for hoses connection kit, cod. RRNS05/06, is suggested in case of compositions with top-mounted taps L 595 L from 700 to 0 mm - Unit price URS01 L from 1 to 1500 mm. - Unit price URS02 L from 1501 to 2000 mm - Unit price URS03 L from 2001 to 2500 mm - Unit price URS

137 S u s p e n d e d t o p s PIANURA (esign Monica Armani ) Tops with width below the minimum specified are not feasible. Top adjacent to back-splash in CRISTALPLANT - P 565 mm With under-mounted UNIVERSAL SMALL washbasin, L = min 850 mm. With under-mounted UNIVERSAL BIG washbasin, L = min 1 mm. The extension for hoses connection kit, cod. RRNS05/06, is suggested in case of compositions with top-mounted taps. Not compatible with moulded flush-mounted washbasins. Cristalplant 500 L 565 L from 700 to 0 mm - Unit price URAC01 L from 1 to 1500 mm. - Unit price URAC02 L from 1501 to 2000 mm - Unit price URAC03 L from 2001 to 2500 mm - Unit price URAC04 L from 2501 to 2800 mm - Unit price URAC05 Top detached from back-splash in CRISTALPLANT - P 595 mm Rear LE light. With under-mounted UNIVERSAL SMALL washbasin, L = min 850 mm. With under-mounted UNIVERSAL BIG washbasin, L = min 1 mm. The extension for hoses connection kit, cod. RRNS05/06, is suggested in case of compositions with top-mounted taps. Not compatible with moulded flush-mounted washbasins L 595 L from 700 to 0 mm - Unit price URC01 L from 1 to 1500 mm. - Unit price URC02 L from 1501 to 2000 mm - Unit price URC03 L from 2001 to 2500 mm - Unit price URC04 L from 2501 to 2800 mm - Unit price URC

138 S u s p e n d e d t o p s PIANURA (esign Monica Armani ) Tops with width below the minimum specified are not feasible. Corian Top adjacent to back-splash, with Sabbia washbasin in CORIAN - P 565 mm Moulded flush-mounted thermoformed washbasin in white Corian, without overflow, with white waste drain and universal chromium-plated siphon. Please order separately the possible second washbasin. L = min 1700 mm when 2 Sabbia 6 washbasins are used. L = min 2000 mm when 2 Sabbia 7 washbasins are used. The extension for hoses connection kit, cod. RRNS05/06, is suggested in case of compositions with top-mounted taps. 500 L 565 Sabbia 6 - L from 850 to 0 mm - Unit price URAA01 Sabbia 6 - L from 1 to 1500 mm - Unit price URAA02 Sabbia 7 - L from 1 to 1500 mm - Unit price URAB02 Sabbia 6 - L from 1501 to 2000 mm - Unit price URAA03 Sabbia 7 - L from 1501 to 2000 mm - Unit price URAB03 Sabbia 6 - L from 2001 to 2500 mm - Unit price URAA04 Sabbia 7 - L from 2001 to 2500 mm - Unit price URAB04 Sabbia 6 - L from 2501 to 3000 mm - Unit price URAA05 Sabbia 7 - L from 2501 to 3000 mm - Unit price URAB05 15 Top detached from back-splash, with Sabbia washbasin in CORIAN - P 595 mm Rear LE light. Moulded flush-mounted thermoformed washbasin in white Corian, without overflow, with white waste drain and universal chromium-plated siphon. Please order separately the possible second washbasin. L = min 1700 mm when 2 Sabbia 6 washbasins are used. L = min 2000 mm when 2 Sabbia 7 washbasins are used. The extension for hoses connection kit, cod. RRNS05/06, is suggested in case of compositions with top-mounted taps. 500 L 595 Sabbia 6 - L from 850 to 0 mm - Unit price URA01 Sabbia 6 - L from 1 to 1500 mm - Unit price URA02 Sabbia 7 - L from 1 to 1500 mm - Unit price URB02 Sabbia 6 - L from 1501 to 2000 mm - Unit price URA03 Sabbia 7 - L from 1501 to 2000 mm - Unit price URB03 Sabbia 6 - L from 2001 to 2500 mm - Unit price URA04 Sabbia 7 - L from 2001 to 2500 mm - Unit price URB04 Sabbia 6 - L from 2501 to 3000 mm - Unit price URA05 Sabbia 7 - L from 2501 to 3000 mm - Unit price URB

139 S u s p e n d e d t o p s PIANURA (esign Monica Armani ) Specific customised solutions Please refer to PIANURA TECHNICAL SHEET for the selection of electrical devices and their positioning. Please see the standard cut-outs (washbasin or tap holes) on chapter Customised Solutions. Electronic control unit For LE lights + any sockets and/or power buttons. The electronic control unit is required ONLY when sockets and/or power buttons are positioned on Pianura back-splash (not to be ordered in case of remote light button and blacksplash without sockets). Voltage V - 50 Hz ZZACF27 Voltage V - 60 Hz ZZACF26 Hole on back-splash including single socket with cover (IP 44) A B C E F G A - Germany - Austria - Holland (VE) ZFACF10 B - France - Belgium - Poland ZFACF11 C - Sockets for Switzerland (10A) ZFACF12 - UK ZFACF14 E - Italy (10A / 16A) ZFACF15 F - US ZFACF16 G - Australia ZFACF17 Hole on back-splash including light button (IP 44) To be used as an alternative to possible remote control supplied by the customer ZFACG01 Hole for recessed tap, on back-splash. Compatible with WINGS taps art. RHNS01 / RHNS02. Cristalplant - Corian ZNB09 Stone - Marble - Granite - Composite ZNB

140 S u s p e n d e d t o p s FLYER (esign C.R.S. Boffi ) TECHNICAL FEATURES Suspended top, which can be fitted with washbasin and tap. TOPS CRISTALPLANT : support made of 12 mm thick wood particle boards panels, white, waterproof (class V), with low formaldehyde emission (class E1), treated with high performance melamine resin. Edges in ABS, same colour. Outer structure in 15 mm thick Cristalplant. Optional lower covering panel in white melamine. Colour: white. Compatibility: top-mounted - built-in - moulded flush-mounted Cristalplant - under-mounted washbasins. CORIAN : support made of 12 mm thick wood particle boards panels, white, waterproof (class V), with low formaldehyde emission (class E1), treated with high performance melamine resin. Edges in ABS, same colour. Outer structure in 12 mm thick Corian. Optional lower covering panel in white melamine. Colour: white. Compatibility: feasible ONLY with moulded flush-mounted washbasin mod. SABBIA 6 / 7. SOLI WOO: support made of 15 mm thick strip-wood panels (20 mm for old grey pinewood). Outer structure (visible vertical, lower and upper surfaces) made of 5 mm thick solid wood panels, 45 mitred and assembled. Optional lower covering panel made of solid wood panels, treated with water-based matt paints, with oil effect. Species: natural oak (with knots) - LIGHT Canaletto walnut "sawn effect" - Old grey pinewood. Compatibility: top-mounted and built-in top-mounted washbasins. 15 STONE, MARBLE, GRANITE, COMPOSITE: support in thermosetting polymer polyurethane foam (light, stable over time, waterproof and resistant to thermal shock), plated - on the lower part - with 10+2 mm thick white ABS. Outer structure made of 20 mm solid stone-marble-granite-composite panels, 45 mitred and assembled. Optional lower covering panel in white or black melamine. Finishes: stone-marble-granite-composites (complete range). Compatibility: top-mounted - built-in - under-mounted washbasins. Please add the specific holes for washbasin and tap integration. THICKNESS: mm. EPTH: 500 mm. (upon request, without an extra charge, it can be reduced up to 450 mm, except for Corian ) / 600 mm. SUPPORTING BRACKETS Made of steel, painted with epoxy powders. For external fixing. Please order them separately, in the quantity indicated. Colour: matt white. 15.8

141 S u s p e n d e d t o p s FLYER (esign C.R.S. Boffi ) ice per linear metre. The lower covering panel is feasible only when the washbasins are top-mounted. The price of tops with width below the standard minimum is the same as the price for the minimum top width. FLYER - Suspended top in CRISTALPLANT. Compatible with top-mounted, built-in or under-mounted washbasins. NOT compatible with moulded flush-mounted washbasins mod. SABBIA 1, SABBIA 2, KUPA. Min. W. 850 mm. Max W mm. The depth can be reduced to 450 mm, upon request and without a price increase. Versions: without lower covering panel / with white melamine lower covering panel. Please order the brackets separately. L 500/600 P 500 mm Without lower covering panel. - ice per linear metre TQAGCJ1 With lower covering panel. - ice per linear metre TQAGCJ2 P 600 mm Without lower covering panel. - ice per linear metre TQAPHJ1 With lower covering panel. - ice per linear metre TQAPHJ2 FLYER - Suspended top in CRISTALPLANT, with Kupa washbasin. L Moulded flush-mounted KUPA washbasin in Cristalplant. Min. W. 850 mm. Max W mm. Without lower covering panel. Please order the brackets separately. Please order separately the possible second washbasin (cod. WZKPAJ001). L = min 2000 mm when 2 washbasins are used P 500 mm ice per linear metre TQAGCKP FLYER - Suspended top in CORIAN, with Sabbia washbasin. L Min. W. 850 mm. Max W mm. SABBIA 6 or SABBIA 7 moulded flush-mounted washbasin in Corian. Without lower covering panel. Please order the brackets separately. Please order separately the possible second washbasin (cod. ZTRBK01 - ZTRBK02). L = min 1700 mm when 2 Sabbia 6 washbasins are used. L = min 2000 mm when 2 Sabbia 7 washbasins are used. 15 P 500 mm With Sabbia 6. - ice per linear metre TRAGCS6 With Sabbia 7 - ice per linear metre TRAGCS7 FLYER - Suspended top in SOLI WOO L Compatible with top-mounted and built-in washbasins. Min. W. 850 mm. Max. width: 3000 mm (old grey pinewood: 2800 mm). The depth can be reduced to 450 mm, upon request and without a price increase. Versions: without lower covering panel / with lower covering panel in solid wood, same species of top. Please order the brackets separately. ABONOS OAK: upon request it's feasible in Abonos Oak solid wood, with a +50% price increase. 500/600 P 500 mm Without lower covering panel. - ice per linear metre TTJGCJ1 With lower covering panel. - ice per linear metre TTJGCJ2 P 600 mm Without lower covering panel. - ice per linear metre TTJPHJ1 With lower covering panel. - ice per linear metre TTJPHJ2 15.9

142 S u s p e n d e d t o p s FLYER (esign C.R.S. Boffi ) Unit price. The lower covering panel is feasible only when the washbasins are top-mounted. The price of tops with width below the standard minimum is the same as the price for the minimum top width. Stone A Stone B Stone C Stone Stone E FLYER - Suspended top in STONE, MARBLE, GRANITE, COMPOSITE. L Compatible with top-mounted, built-in and under-mounted washbasins. Min. W. 850 mm. Max. width: see THE GENERAL TECHNICAL PART (INFO). Please see the section PRICE RANGES (INFO) for the price categories. The depth can be reduced to 450 mm, upon request and without a price increase. Versions: without lower covering panel / with lower white or black melamine covering panel (on the order please specify the desired colour). Please order the brackets separately. 500/600 P 500 mm L from 900 to 1500 mm - Without lower covering panel. - Unit price TMRGCJ3 L from 1501 to 2000 mm - Without lower covering panel. - Unit price TMRGCJ4 L from 2001 to 2500 mm - Without lower covering panel. - Unit price TMRGCJ5 L from 2501 to 3000 mm - Without lower covering panel. - Unit price TMRGCJ6 L from 900 to 1500 mm - With lower covering panel. - Unit price TMRGCJ7 L from 1501 to 2000 mm - With lower covering panel. - Unit price TMRGCJ8 L from 2001 to 2500 mm - With lower covering panel. - Unit price TMRGCJ9 L from 2501 to 3000 mm - With lower covering panel. - Unit price TMRGCK0 P 600 mm L from 900 to 1500 mm - Without lower covering panel. - Unit price TMRPHJ3 L from 1501 to 2000 mm - Without lower covering panel. - Unit price TMRPHJ4 L from 2001 to 2500 mm - Without lower covering panel. - Unit price TMRPHJ5 L from 2501 to 3000 mm - Without lower covering panel. - Unit price TMRPHJ6 L from 900 to 1500 mm - With lower covering panel. - Unit price TMRPHJ7 L from 1501 to 2000 mm - With lower covering panel. - Unit price TMRPHJ8 L from 2001 to 2500 mm - With lower covering panel. - Unit price TMRPHJ9 L from 2501 to 3000 mm - With lower covering panel. - Unit price TMRPHK0 15 Supporting bracket, external fixing. Steel, matt white painted / 470 RIM07 FINO A ESAURIMENTO SCORTE L 700 mm / 0 mm > 2 brackets L 1 mm / 1500 mm > 3 brackets L 1501 mm / 2000 mm > 4 brackets L 2001 mm / 2500 mm > 5 brackets L 2501 mm / 3000 mm > 6 brackets For top P 500 mm ATY006 For top P 600 mm ATY

143 T o p s NOTE TO ESIGNER COMPATIBILITY TOPS > WASHBASINS This chapter indicates, with specific symbols, the compatibility between washbasin and tops. To select a washbasin please refer to the compatibility with top chapter. Symbols of washbasin typologies. TOP-MOUNTE BUILT-IN UNER-MOUNTE moulded FLUSH-MOUNTE CUT-OUTS FOR WASHBASINS RIM04 / RIM10 FINO A ESAURIMENTO SCORTE 1 - TOP IN CRISTALPLANT + UNER-MOUNTE WASHBASIN IN CRISTALPLANT O NOT add the cut-out for washbasin. The price includes the washbasin and the gluing process. 2 - TOP IN CRISTALPLANT or CORIAN + MOULE FLUSH-MOUNTE WASHBASIN IN CRISTALPLANT or CORIAN. O NOT add the cut-out for washbasin. The price includes the washbasin moulding process cost. 3 - TOP IN GLASS + UNER-MOUNTE WASHBASIN Please add always the cut-out for under-mounted washbasin cod. ZNBA10 and the under top washbasin gluing cod. ZNB OTHER COMBINATIONS TOP + WASHBASIN For any other combination of top and washbasins listed in the price list (except for the WOO-IN tops for GAREN washbasin, which are supplied with cut-out), please add the cut-out for top-mounted washbasin cod. ZNBA09 or the cut-out for under-mounted washbasin cod. ZNBA10 (see chapter Customised Solutions - ice Increases - Maintenance). 5 - OTHER CUSTOMISE SOLUTIONS Other specific customised solutions shall be added to the top (i.e. the tap hole cod. ZNB01) accordingly to the design of the composition. 16.3

144 T o p s PROGRAMMA STANAR - SIMPLE - FREE ZONE ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in CRISTALPLANT - Thickness: 15 mm 15 Width: min. 600 mm, max mm. IMPORTANT! : The cut-out and gluing costs of UNER-MOUNTE WASHBASINS in Cristalplant is included in the washbasin price. Please order the specific top cod. TQABJS1 when moulded flush-mounted washbasins are used. ice per linear metre TQABJA5 Unit prices White Top in CRISTALPLANT for moulded flush-mounted washbasin - Thickness: 15 mm 15 Width: min. 600 mm, max mm. To be used ONLY with SABBIA 1, SABBIA 2 and KUPA washbasins (moulding process is included: IT'S NOT necessary to add the cut-out for washbasin and/or price for gluing). 16 ice per linear metre TQABJS1 Unit prices White Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

145 T o p s PROGRAMMA STANAR - SIMPLE - FREE ZONE ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in LASERMAT - Thickness: 20 mm 20 Width: min. 600 mm, max mm. To be used ONLY with TOP-MOUNTE and BUILT-IN washbasins. Customised angles or pillar cut-outs are NOT feasible. Please add any cut-out for TOP-MOUNTE washbasin cod. ZNBA09 and/or holes for tap. ice per linear metre TLSCJA5 Unit prices Alaska white 183 Kos white 178 Malè white 179 Luxor beige 180 Ottawa beaver 181 Londra grey 184 Efeso grey 185 Bromo grey 182 Ingo black Top in CORIAN - Thickness: 20 mm Width: min. 0 mm, max mm. To be used ONLY with TOP-MOUNTE and BUILT-IN washbasins. Please add any cut-out for TOP-MOUNTE washbasin cod. ZNBA09 and/or holes for tap ice per linear metre TRACJA5 Unit prices White Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

146 T o p s PROGRAMMA STANAR - SIMPLE - FREE ZONE ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Stone A Stone B Stone C Stone Stone E Top in STONE, MARBLE, GRANITE, COMPOSITE - Thickness: 20 mm 20 Width: min. 600 mm. Max. width: see THE GENERAL TECHNICAL PART (INFO). Please see the letter written in the finish picture for the price categories. Please add any cut-out for washbasin and/or holes for tap. ice per linear metre TMRCJA5 Unit prices STONE - MARBLE - GRANITE A A B B B C E E 240 Marble White Carrara 250 Stone Serena 200 Stone Cardoso 245 Stone Matraia Granite Quartzite Black absolute Silver Zimbabwe 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone 259 Quartzite Calacatta COMPOSITE SILESTONE C C C 432 Expo grey 433 Concrete grey 435 Tebas black 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 16 Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

147 T o p s PROGRAMMA STANAR - SIMPLE - FREE ZONE ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in SOLI WOO - Thickness: 23 mm 23 Width: min. 600 mm, max mm (Old grey pinewood: 2800 mm). To be used ONLY with TOP-MOUNTE and BUILT-IN washbasins. Please add any cut-out for TOP-MOUNTE washbasin cod. ZNBA09 and/or holes for tap. NEW ice per linear metre TTJA5 Unit prices SOLI WOO 058 Canaletto LIGHT walnut sawn-effect 057 Old grey pinewood 16 Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

148 T o p s PROGRAMMA STANAR - SIMPLE ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in GLASS - Thickness: 12 mm 12 Width: min. 600 mm, max mm. Please add any cut-out for washbasin and/or holes for tap. In case of use of UNER-MOUNTE washbasins please add always the price for gluing cod. ZNB07. ice per linear metre TGAAVA5 Unit prices GLASS FROSTE PAINTE EXTRALIGHT 818 White 816 ove grey 817 Coffee T o p s PROGRAMMA STANAR - SIMPLE ice per linear metre Tops with width below the minimum specified are not feasible. Top in GLASS, with moulded flush-mounted washbasin - Thickness: 12 mm max Extralight glass, painted sanded > the Extralight glass used on these tops is sandblasted and not frosted. This working process can change the tone of the same colour in frosted version, this can not be consider cause for a complaint. Width: min. 900 mm, max mm. Washbasin without overflow, with waste drain cod. ANBN002 chromium-plated (free-flow waste), with plug covered by glass. Compatible siphon: ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. Compositions with 2 washbasins are feasible ONLY using two tops pull together. Please add any holes for tap. Any small difference or imperfection from a sample is to be considered characteristic of the artisanal processing, that make each piece unique. 16 Central washbasin TGAAZG5 136,8 Top in GLASS, with moulded flush-mounted washbasin - Thickness: Extralight glass, painted sanded > the Extralight glass used on these tops is sandblasted and 12 mm not frosted. This working process can change the tone of the same colour in frosted version, this can not be consider cause for a complaint. Width: min. 900 mm, max mm. ouble washbasin not available. max 2985 Washbasin without overflow, with waste drain cod. ANBN002 chromium-plated (free-flow waste), with plug covered by glass. max 2985 Compatible siphon: ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. 310 max rawn=left (S), mirrored=right (). Compositions with 2 washbasins are feasible ONLY using two tops pull together.any small 10 difference or imperfection from a sample is to be considered characteristic of the artisanal processing, that make each piece unique. min 450 max 600 Lateral washbasin TGAAZG6 S- 136,8 GLASS SANE PAINTE EXTRALIGHT 818 White 816 ove grey 817 Coffee Main CUSTOMISE SOLUTIONS: Tap hole > ZNB

149 T o p s XILA BATH ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in CRISTALPLANT - Thickness: mm 15 Width: min. 600 mm, max mm. IMPORTANT! : The cut-out and gluing costs of UNER-MOUNTE WASHBASINS in Cristalplant is included in the washbasin price. Please order the specific top cod. TQABJXF when moulded flush-mounted washbasins are used. 50 ice per linear metre TQABJXB - White Top in CRISTALPLANT for moulded flush-mounted washbasin - Thickness: mm 15 Width: min. 600 mm, max mm. To be used ONLY with SABBIA 1, SABBIA 2 and KUPA washbasins (moulding process is included: IT'S NOT necessary to add the cut-out for washbasin and/or price for gluing). Under-top front panel H 50 mm included ice per linear metre TQABJXF - White Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

150 T o p s XILA BATH ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. 50 Stone A Stone B Stone C Stone Stone E Top in STONE, MARBLE, GRANITE, COMPOSITE - Thickness: mm 20 Width: min. 600 mm. Max. width: see THE GENERAL TECHNICAL PART (INFO). Please see the letter written in the finish picture for the price categories. Feasible in all range options of MARBLE, STONE, GRANITE, SILESTONE and EKTON. Under-top front panel H 50 mm included. ice per linear metre TMRCJXB STONE - MARBLE - GRANITE A A B B B C E E 240 Marble White Carrara 250 Stone Serena 200 Stone Cardoso 245 Stone Matraia Granite Quartzite Black absolute Silver Zimbabwe 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone 259 Quartzite Calacatta COMPOSITE SILESTONE C C C 432 Expo grey 433 Concrete grey 435 Tebas black 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 16 Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

151 T o p s XILA BATH ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width Stone A Stone B Stone C Stone Stone E Top in COMPOSITE - Thickness: mm Top in CORIAN - Thickness: mm Width: min. 600 mm. Max. width: see THE GENERAL TECHNICAL PART (INFO). Please see the section PRICE RANGES (INFO) for the price categories. Feasible in all range options of SILESTONE or EKTON. Under-top front panel H 50 mm included. ice per linear metre TMRAVXB COMPOSITE SILESTONE 432 Expo grey C C 433 Concrete grey COMPOSITE EKTON 455 Edora beige 452 Kadum brown 435 Tebas black 453 Sirius black C 431 Zeus white 454 Zenith white E 437 Lagoon white 456 Irok beige E 436 Yukon white 451 Strato grey E 438 Kensho grey 457 Ventus grey E Width: min. 0 mm, max mm. To be used ONLY with TOP-MOUNTE washbasins. 434 Unsui brown 458 Korus grey E 439 Merope greybrown E 459 Galema brown 440 oradus black 16 ice per linear metre TRACJXB 173 White Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

152 T o p s B14 ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in CRISTALPLANT - Thickness: 50 mm Width: min. 600 mm, max mm. Frontal bevelled edge. IMPORTANT! : The cut-out and gluing costs of UNER-MOUNTE WASHBASINS in Cristalplant is included in the washbasin price. 505 ice per linear metre TQAJAW1 - White edge Please consider to add a customisation/cut-out on each side. Alternately it s possible to have a 35 edge, according to design requirements. Cristalplant - Unit price ZTLHP01 S- 35 sloping edge Please consider to add a customisation/cut-out on each side. Alternately it s possible to have a 90 edge, according to design requirements. Cristalplant - Unit price ZTLHP02 S- Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

153 T o p s B14 ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Stone A Stone B Stone C Stone Stone E Top in STONE, MARBLE, GRANITE, COMPOSITE - Thickness: 50 mm Width: min. 600 mm. Max. width: see THE GENERAL TECHNICAL PART (INFO). Please see the letter written in the finish picture for the price categories. Please add any cut-out for washbasin and/or holes for tap. 505 ice per linear metre TMRJAW1 STONE - MARBLE - GRANITE A A B B B C E E 240 Marble White Carrara 250 Stone Serena 200 Stone Cardoso 245 Stone Matraia Granite Quartzite Black absolute Silver Zimbabwe 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone 259 Quartzite Calacatta COMPOSITE SILESTONE C C C 432 Expo grey 433 Concrete grey 435 Tebas black 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 90 edge Please consider to add a customisation/cut-out on each side. Alternately it s possible to have a 35 edge, according to design requirements. 16 Stone, marble, granite, composite - Unit price ZPMHP03 S- 35 sloping edge Please consider to add a customisation/cut-out on each side. Alternately it s possible to have a 90 edge, according to design requirements. Stone, marble, granite, composite - Unit price ZPMHP04 S- Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

154 T o p s I FIUMI ST ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in CRISTALPLANT - Thickness: 20 mm 20 Width: min. 600 mm, max mm. 45 edges on 3 sides. IMPORTANT! : The cut-out and gluing costs of UNER-MOUNTE WASHBASINS in Cristalplant is included in the washbasin price. ice per linear metre TQAPEC7 - White Top in CORIAN for moulded flush-mounted washbasin - Thickness: 20 mm 20 Width: min. 600 mm, max mm. 45 edges on 3 sides. Please order separately any SABBIA 6 or SABBIA 7 washbasin (the moulding process is included in the price: it's not necessary to add any washbasin cut-out and/or gluing process). 16 To be used only with SABBIA 6 and SABBIA 7 washbasins (thermoformed) - ice per linear metre TRAPEC7 173 White Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

155 T o p s I FIUMI ST ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Stone A Stone B Stone C Stone Stone E Top in STONE, MARBLE, GRANITE, COMPOSITE - Thickness: 20 mm 20 Width: min. 600 mm. Max. width: see THE GENERAL TECHNICAL PART (INFO). Please see the letter written in the finish picture for the price categories. Please add any cut-out for washbasin and/or holes for tap. ice per linear metre TMRPEC7 STONE - MARBLE - GRANITE A A B B B C E E 240 Marble White Carrara 250 Stone Serena 200 Stone Cardoso 245 Stone Matraia Granite Quartzite Black absolute Silver Zimbabwe 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone 259 Quartzite Calacatta COMPOSITE SILESTONE C C C 432 Expo grey 433 Concrete grey 435 Tebas black 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON E E E E E E 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white 456 Irok beige 451 Strato grey 457 Ventus grey 458 Korus grey 459 Galema brown 16 Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

156 T o p s SOHO - WOO-IN ice per linear metre When used on WOO-IN cabinets, it is compatible ONLY with TOP-MOUNTE washbasins: please add a double cut-out for washbasin - cod. ZNBA09 - on top and on cabinet. The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in CRISTALPLANT - Thickness: 15 mm 15 Width: min. 600 mm, max mm. IMPORTANT! : The cut-out and gluing costs of UNER-MOUNTE WASHBASINS in Cristalplant is included in the washbasin price. Please order the specific top cod. TQABFS1 when flush-mounted washbasins are used. ice per linear metre TQABFA5 Unit prices White Top in GLASS - Thickness: 12 mm 12 Width: min. 600 mm, max mm. Please add any cut-out for washbasin and/or holes for tap. In case of use of UNER-MOUNTE washbasins please add always the price for gluing cod. ZNB ice per linear metre TGAAXA5 Unit prices GLASS FROSTE PAINTE EXTRALIGHT 818 White 816 ove grey 817 Coffee Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

157 T o p s SOHO - WOO-IN ice per linear metre When used on WOO-IN cabinets, it is compatible ONLY with TOP-MOUNTE washbasins: please add a double cut-out for washbasin - cod. ZNBA09 - on top and on cabinet. The price of tops with widths below the standard minimum is the same as price for the minimum top width. Stone A Stone B Stone C Stone Stone E Top in STONE, MARBLE, GRANITE, COMPOSITE - Thickness: 20 mm 20 Width: min. 600 mm. Max. width: see THE GENERAL TECHNICAL PART (INFO). Please see the letter written in the finish picture for the price categories. Please add any cut-out for washbasin and/or holes for tap. ice per linear metre TMRCFA5 Unit prices STONE - MARBLE - GRANITE A A B B B C E E 240 Marble White Carrara 250 Stone Serena 200 Stone Cardoso 245 Stone Matraia Granite Quartzite Black absolute Silver Zimbabwe 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone 259 Quartzite Calacatta COMPOSITE SILESTONE C C C 432 Expo grey 433 Concrete grey 435 Tebas black 431 Zeus white 437 Lagoon white 436 Yukon white 438 Kensho grey 434 Unsui brown 439 Merope greybrown 440 oradus black COMPOSITE EKTON 455 Edora beige 452 Kadum brown 453 Sirius black 454 Zenith white E 456 Irok beige E 451 Strato grey E 457 Ventus grey E 458 Korus grey E E 459 Galema brown 16 Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

158 T o p s SOHO ice per linear metre The price of tops with widths below the standard minimum is the same as price for the minimum top width. Top in CRISTALPLANT for moulded flush-mounted washbasin - Thickness: 15 mm 15 Width: min. 600 mm, max mm. To be used only with SABBIA 1 and SABBIA 2 washbasins (moulding process is included: IT'S NOT necessary to add the cut-out for washbasin and/or price for gluing). ice per linear metre TQABFS1 Unit prices White 16 Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Cut-out for UNER-MOUNTE washbasin > ZNBA10 Tap hole > ZNB

159 T o p s SOHO ice per linear metre Tops with width below the minimum specified are not feasible. Top in GLASS, with moulded flush-mounted washbasin - Thickness: 12 mm max Extralight glass, painted sanded > the Extralight glass used on these tops is sandblasted and not frosted. This working process can change the tone of the same colour in frosted version, this can not be consider cause for a complaint. Width: min. 900 mm, max mm. Washbasin without overflow, with waste drain cod. ANBN002 chromium-plated (free-flow waste), with plug covered by glass. Compatible siphon: ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. Compositions with 2 washbasins are feasible ONLY using two tops pull together. Please add any holes for tap. Any small difference or imperfection from a sample is to be considered characteristic of the artisanal processing, that make each piece unique. Central washbasin - ice per linear metre TGAAYG5 Top in GLASS, with moulded flush-mounted washbasin - Thickness: 12 mm max max 150 min 455 max 605 max Extralight glass, painted sanded > the Extralight glass used on these tops is sandblasted and not frosted. This working process can change the tone of the same colour in frosted version, this can not be consider cause for a complaint. Width: min. 900 mm, max mm. ouble washbasin not available. Washbasin without overflow, with waste drain cod. ANBN002 chromium-plated (free-flow waste), with plug covered by glass. Compatible siphon: ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. rawn=left (S), mirrored=right (). Compositions with 2 washbasins are feasible ONLY using two tops pull together.please add any holes for tap. Please add any holes for tap. Any small difference or imperfection from a sample is to be considered characteristic of the artisanal processing, that make each piece unique. 16 Lateral washbasin - ice per linear metre TGAAYG6 S- GLASS SANE PAINTE EXTRALIGHT 818 White 816 ove grey 817 Coffee Main CUSTOMISE SOLUTIONS: Tap hole > ZNB

160 T o p s WOO-IN for GAREN washbasin Unit price. If other Boffi top-mounted washbasins are used, please order SOHO / WOO-IN cod. TQABFA5 / TMRCFA5 / TGAAXA5 tops. CUSTOMISATIONS ARE NOT FEASIBLE. The internal bottom cover of the GAREN washbasin in STONE, MARBLE, GRANITE finish is cut-out from the same sheet of the top, to guarantee a continuous grain. Stone A: available ONLY in white CARRARA marble. Stone B: available ONLY in Cardoso stone. Stone C: available ONLY in QUARTZITE SILVER. Stone : available ONLY in Black Cosmic granite / Emperador ark marble. Stone E: available ONLY in GREY STONE marble / Quartzite Calacatta. Stone A Stone B Stone C Stone Stone E Corian Top for washbasin GAREN - L 905 mm. = = Compatible cabinets: please see the compatibility technical chart. Arranged for GAREN washbasin, to be ordered separately. The price includes the cut-out for washbasin. Please consider to add a cut-out for top-mounted washbasin on cabinet, cod. ZNBA09. Tap holes are not feasible on tops in STONE, MARBLE, GRANITE: please order wall-mounted taps. STONE, MARBLE, GRANITE - Unit price TMRAY01 CORIAN - Unit price TRAAX01 STONE - MARBLE - GRANITE A 240 Marble White Carrara 200 Stone Cardoso B 257 Quartzite Silver C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E GAREN CORIAN GAREN 173 White COMPATIBILITIES WITH MONOBLOC BASE UNITS BWANZ090WS BWAMT120WS BWAMU150WS BWAMT150WS BWANZ090W BWAMT120W BWAMU150W BWAMT150W BWAMQ180WS BWAMQ180W BWAMS180WS BWAMS180W Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Tap hole > ZNB

161 T o p s WOO-IN for GAREN washbasin Unit price. If other Boffi top-mounted washbasins are used, please order SOHO / WOO-IN cod. TQABFA5 / TMRCFA5 / TGAAXA5 tops. CUSTOMISATIONS ARE NOT FEASIBLE. The internal bottom cover of the GAREN washbasin in STONE, MARBLE, GRANITE finish is cut-out from the same sheet of the top, to guarantee a continuous grain. Stone A: available ONLY in white CARRARA marble. Stone B: available ONLY in Cardoso stone. Stone C: available ONLY in QUARTZITE SILVER. Stone : available ONLY in Black Cosmic granite / Emperador ark marble. Stone E: available ONLY in GREY STONE marble / Quartzite Calacatta. Stone A Stone B Stone C Stone Stone E Corian Top for washbasin GAREN - L 1205 mm. 480 = 1205 = Compatible cabinets: please see the compatibility technical chart. Arranged for GAREN washbasin, to be ordered separately. The price includes the cut-out for washbasin. Please consider to add a cut-out for top-mounted washbasin on cabinet, cod. ZNBA09. Tap holes are not feasible on tops in STONE, MARBLE, GRANITE: please order wall-mounted taps. STONE, MARBLE, GRANITE - Unit price TMRAY02 CORIAN - Unit price TRAAX02 STONE - MARBLE - GRANITE A 240 Marble White Carrara 200 Stone Cardoso B 257 Quartzite Silver C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E GAREN CORIAN GAREN 173 White COMPATIBILITIES WITH MONOBLOC BASE UNITS BWANZ120WS BWANZ120W Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Tap hole > ZNB

162 T o p s WOO-IN for GAREN washbasin Unit price. If other Boffi top-mounted washbasins are used, please order SOHO / WOO-IN cod. TQABFA5 / TMRCFA5 / TGAAXA5 tops. CUSTOMISATIONS ARE NOT FEASIBLE. The internal bottom cover of the GAREN washbasin in STONE, MARBLE, GRANITE finish is cut-out from the same sheet of the top, to guarantee a continuous grain. Stone A: available ONLY in white CARRARA marble. Stone B: available ONLY in Cardoso stone. Stone C: available ONLY in QUARTZITE SILVER. Stone : available ONLY in Black Cosmic granite / Emperador ark marble. Stone E: available ONLY in GREY STONE marble / Quartzite Calacatta. Stone A Stone B Stone C Stone Stone E Corian Top for washbasin GAREN - L 1205 mm. 452, Compatible cabinets: please see the compatibility technical chart. Arranged for GAREN washbasin, to be ordered separately. The price includes the cut-out for washbasin. Reversible top, left (S) right (). Please consider to add a cut-out for top-mounted washbasin on cabinet, cod. ZNBA09. Tap holes are not feasible on tops in STONE, MARBLE, GRANITE: please order wall-mounted taps. STONE, MARBLE, GRANITE - Unit price TMRAY03 CORIAN - Unit price TRAAX03 STONE - MARBLE - GRANITE A 240 Marble White Carrara 200 Stone Cardoso B 257 Quartzite Silver C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E GAREN CORIAN GAREN 173 White COMPATIBILITIES WITH MONOBLOC BASE UNITS 16 BWAMU150WS BWAMT150WS BWAMQ180WS BWAMS180WS BWAMU150W BWAMT150W BWAMQ180W BWAMS180W Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Tap hole > ZNB

163 T o p s WOO-IN for GAREN washbasin Unit price. If other Boffi top-mounted washbasins are used, please order SOHO / WOO-IN cod. TQABFA5 / TMRCFA5 / TGAAXA5 tops. CUSTOMISATIONS ARE NOT FEASIBLE. The internal bottom cover of the GAREN washbasin in STONE, MARBLE, GRANITE finish is cut-out from the same sheet of the top, to guarantee a continuous grain. Stone A: available ONLY in white CARRARA marble. Stone B: available ONLY in Cardoso stone. Stone C: available ONLY in QUARTZITE SILVER. Stone : available ONLY in Black Cosmic granite / Emperador ark marble. Stone E: available ONLY in GREY STONE marble / Quartzite Calacatta. Stone A Stone B Stone C Stone Stone E Corian Top for washbasin GAREN - L 1355 mm ,5 480 Compatible cabinets: please see the compatibility technical chart. Arranged for GAREN washbasin, to be ordered separately. The price includes the cut-out for washbasin. Reversible top, left (S) right (). Please consider to add a cut-out for top-mounted washbasin on cabinet, cod. ZNBA09. Tap holes are not feasible on tops in STONE, MARBLE, GRANITE: please order wall-mounted taps. STONE, MARBLE, GRANITE - Unit price TMRAY04 CORIAN - Unit price TRAAX04 STONE - MARBLE - GRANITE A 240 Marble White Carrara 200 Stone Cardoso B 257 Quartzite Silver C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E GAREN CORIAN GAREN 173 White COMPATIBILITIES WITH MONOBLOC BASE UNITS BWAMT180WS BWAMT180W BWAMU180WS BWAMU180W Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Tap hole > ZNB

164 T o p s WOO-IN for GAREN washbasin Unit price. If other Boffi top-mounted washbasins are used, please order SOHO / WOO-IN cod. TQABFA5 / TMRCFA5 / TGAAXA5 tops. CUSTOMISATIONS ARE NOT FEASIBLE. The internal bottom cover of the GAREN washbasin in STONE, MARBLE, GRANITE finish is cut-out from the same sheet of the top, to guarantee a continuous grain. Stone A: available ONLY in white CARRARA marble. Stone B: available ONLY in Cardoso stone. Stone C: available ONLY in QUARTZITE SILVER. Stone : available ONLY in Black Cosmic granite / Emperador ark marble. Stone E: available ONLY in GREY STONE marble / Quartzite Calacatta. Stone A Stone B Stone C Stone Stone E Corian Top for double washbasin GAREN - L 1788 mm. 452, ,5 480 Compatible cabinets: please see the compatibility technical chart. Arranged for 2 GAREN washbasins, to be ordered separately. The price includes the cut-out for washbasin. Please consider to add a cut-out for top-mounted washbasin on cabinet, cod. ZNBA09. Because of technical reasons, the top in STONE, MARBLE, GRANITE with double washbasin is 20 mm thick and not 10 mm. Tap holes are not feasible on tops in STONE, MARBLE, GRANITE: please order wall-mounted taps. STONE, MARBLE, GRANITE - Unit price TMRAY05 CORIAN - Unit price TRAAX05 STONE - MARBLE - GRANITE A 240 Marble White Carrara 200 Stone Cardoso B 257 Quartzite Silver C 261 Marble Emperador ark 254 Granite Black Cosmic 260 Marble Grey Stone E 259 Quartzite Calacatta E GAREN CORIAN GAREN 173 White COMPATIBILITIES WITH MONOBLOC BASE UNITS BWAMR180WS BWAMR180W Main CUSTOMISE SOLUTIONS: Cut-out for TOP-MOUNTE / built-in washbasin > ZNBA09 Tap hole > ZNB

165 C u s t o m i s e d s o l u t i o n s TOPS / SHELVES Cut-out for TOP-MOUNTE / built-in washbasin. For washbasins design Boffi. On the order please specify the washbasin to be installed. In case of washbasins by Client the order must include the technical drawings for any necessary cut-out. To be ordered in case of washbasins mounted on WOO-IN units too. Lasermat - Wood - Cristalplant - Corian - Solid wood ZNBA09 Stone - Marble - Granite - Composite ZNBA09 Glass ZNBA09 Cut-out for UNER-MOUNTE washbasin. Only for washbasins design Boffi. When under-mounted washbasin in Cristalplant is installed on top in Cristalplant, the cut-out is included. The washbasin gluing is included when tops are in Stone, Marble, Granite and Composite. On the order please specify the compatible washbasin to be installed. Stone - Marble - Granite - Composite - Glass ZNBA10 Tap hole. Please add this code for each tap hole. All finishes ZNB01 Hole for WINGS taps. Compatible with WINGS taps cod. RHNS05 / RHNS06. Hole NOT possible on tops in old grey pinewood. 17 Lasermat - Wood - Cristalplant - Corian - Solid wood ZNB08 Stone - Marble - Granite - Composite ZNB08 Under top washbasin gluing. To be used always for under-mounted washbasins matched with glass tops. Glass ZNB

166 C u s t o m i s e d s o l u t i o n s TOPS / SHELVES 1 customised angle. All finishes, Lasermat and Glass excluded ZNB02 Pillar cut-out. On glass tops: radius min. 7 mm. All finishes, Lasermat excluded ZNB03 Cut-out for spotlight on shelf / wall unit. 250 All finishes ZNBE01 Cut-out on back panel for client s switch. 17 All finishes ZNBF01 Milling of shelves / back panels. For joining of shelves and back panels with wood support. Please add this code for each element to be milled. Silcover - Ecolak - Wood - Wood Selection - Polyester - Metals - Solid wood ZNBV

167 C u s t o m i s e d s o l u t i o n s TOPS / SHELVES ice increase for top/shelf or back panel in accordance to client s template. Please send the template All finishes, Lasermat excluded ZNBV02 Polishing of top. % increase on top price. Marble - Granite ZNB05 Flamed and brushed finishing. ice per square meter. Zimbabwe extra black granite ZNB

168 C u s t o m i s e d s o l u t i o n s CABINETS Width, height or depth reduction of cabinet. Unit price - valid also in case of reduction of more than 1 dimension (i.e.: width + depth). Cabinets with shelves ZNBG01 Cabinets with drawers ZNBG02 Width reduction of FREE ZONE cabinets with coplanar door (special rail). ice includes the customised special rail and 2 cabinet reductions code ZNBG01 (these reductions are not charged). Reduction not possible on cabinets L 1200 mm ZBAEA02 Cabinet with dimensions bigger than the standard ones You must absolutely follow the rules. For 1 size increase please consider 1 price increase/customised solution, for 2 or 3 size increases please consider 2 price increases/customised solutions. RRM02 FINO A ESAURIMENTO SCORTE Cabinets with shelves ZNBG05 Cabinets with drawers ZNBG06 Pillar cut-out. 17 Cabinets with shelves ZNBG03 Cut-out on base unit side panel. For washbasin positioning. All finishes ZNBG

169 C u s t o m i s e d s o l u t i o n s CABINETS isassembling of cabinet. Percentage to be added to standard price ZNBG07 Continuous drilling for shelf supports on unit side panels. To be added on each unit ZNBG08 Cabinet supplied without finished parts. Please take Silcover finish price -30% ZNBG09 esign and drawing of a customised cabinet. not referable to any customisation code.? ZNBG10 17 Cut-out for socket. ice includes the cut-out and the socket itself. In the order please specify the socket type (A-B-C--E-F-G-H). A B C E F G H A - Germany - Austria - Holland (VE) ZNBZ01 B - France - Belgium - Poland ZNBZ02 C - Switzerland (10A) ZNBZ03 - enmark ZNBZ04 E - UK ZNBZ05 F - Italy (10A/16A) ZNBZ06 G - USA ZNBZ07 H - Australia ZNBZ

170 P r i c e i n c r e a s e s HANLES WITH PRICE INCREASE Handles with price increase. Unit price per single handle. Valid for all handles with price increase, in all compatible finishes. Please see the sizes and correct positioning under the technical features (in the general part). UNIVERSAL - Compatible finishes: Silcover - Ecolak - Wood - Wood Selection - Polyester - Corian - Wood Exclusive. UEMILAOTTO - Sizes: mm / Compatible finishes: Silcover - Ecolak - Wood (ONLY L 180 mm grey-graphite oak, ash-grey oak and black Eco-wood) - Wood Selection (ONLY L 180 mm core walnut, Canaletto walnut U.S., smoked Oak) - Polyester (only white 003) - Corian - Wood Exclusive (ONLY L 180 mm). 3 - Compatible finishes: Wood 3 (ONLY Core Walnut, Black eco-wood). X12, X36 - Compatible finishes: Silcover - Ecolak - Wood - Wood Selection - Polyester - Corian - Wood Exclusive JZMW01 X3L - Compatible finishes: Solid wood. X3 - Compatible finishes: Wood 3 - Solid wood 3. ZONE - Compatible finishes: all. APRILE - imensions: mm / Compatible finishes: Silcover - Ecolak - Wood - Wood Selection - Polyester - Corian - Wood Exclusive. 17 YAR - Sizes: mm / Compatible finishes: all. 17.8

171 P r i c e i n c r e a s e s CUSTOMISE FINISHES Please consider a 4 weeks time increase for products preparation. When the colour is as sample please calculate the preparation timing referring to the date of acceptance of sample made by Boffi and sent to the customer. ATTENTION! ice increases start from a minimum value of 200,00 (net dealer value, VAT excl.). Custom colour requests with price increases of lesser amounts are considered equal to the minimum charge. SILCOVER % price increase for special colour. The price increase is applied to the price of cabinets in SILCOVER. Fluorescent or metalized colours excluded.? RAL or NCS colour JZAJ03 Colour AS SAMPLE JZAJ04 P r i c e i n c r e a s e s VARIOUS Shipping in wooden crate. ice expressed in EURO, net dealer value, tax excluded. For compositions with net dealer value till EUROS. For compositions with value higher than EUROS please add a price increase each 00 EU- ROS or portion. Example: for a composition of EUROS please consider 3 price increases /for a composition of EUROS please consider 2 price increases JZA

172 M a i n t e n a n c e MATERIALS FOR CLEANING AN MAINTENANCE Clean Set. Package with cleaning products. It includes: Boffi microfibre cloth, gr multipurpose cream. 3 pieces per package AVBL029 Boffi micro-fibre cloth. Antibacterial. 10 pieces per package AVBL017 Stainless Steel Polish Cleaner. In-depth cleaner for stainless steel, aluminium and chromium-plated surfaces. 500 ml bottle. 3 pieces per package AVBL030 Brax cleaner cream. Cleaner for ceramics, resins or composite materials 500 ml bottle pieces per package AVBL020 Casa9 Multipurpose cleaner. Cleaner for any shiny or matt surface. 750 ml bottle. 3 pieces per package AVBL

173 M a i n t e n a n c e MATERIALS FOR CLEANING AN MAINTENANCE Cleaning/maintenance kit for doors and panels in solid wood, oil finish. A B Kit A includes: TRENA 50 ml neutral cleaner + BIVOS 50 ml oil wax + cotton cloth+ abrasive cleaning disc. Kit B includes: REINIGER 250 ml cleaner + PFLEGEÖL 250 ml oil wax. A - For Canaletto walnut sawn-effect AVBL031 B - For LIGHT Canaletto walnut sawn-effect AVBL032 Cleaning kit for surfaces in Lasermat. It includes: ml spray cleaner + sponge + microfibre cloth AVBL033 C1.07 AY - Cleaner for surfaces in stone, marble, granite, composite. 500 ml bottle pieces per package AVBL

174 M a i n t e n a n c e MATERIALS FOR CLEANING AN MAINTENANCE Lacquers and paints - touch-up. 40 ml bottle of water-based touch-up, with small brush. The packages heavier than ml cannot be shipped by air. Silcover White AVAB262 Magnolia AVAB261 Cream AVAB261 Grey AVAB267 Pebble grey AVAB260 Sand AVAB268 Ecrù AVAB260 Mud AVAB260 Greene-brown AVAB260 graphite grey AVAB265 Blue AVAB261 Moka AVAB266 Black AVAB263 Ecolak Arctic white AVAB262 Magnolia AVAB260 Cream AVAB260 Pebble grey AVAB260 Oat colour AVAB268 Ecrù AVAB260 Mud AVAB260 Cloud colour AVAB267 Iron AVAB260 Red AVAB260 Greene-brown AVAB260 Blue AVAB260 Very dark brown AVAB260 Basalt grey AVAB265 Black AVAB263 Charcoal AVAB260 Lacquers and paints - touch-up. ml. bottle of nitro touch-up. The packages heavier than ml cannot be shipped by air. 17 Polyester Any colour of Boffi Polyester range AVAB231 Lacquers and paints - 1 Kg. tin lacquer + catalyst, 1 kg. The packages heavier than ml cannot be shipped by air. Silcover Colour to be chosen from Boffi Silcover range AVAB232 Polyester Colour to be chosen from Boffi Polyester range AVAB

175 M a i n t e n a n c e MATERIALS FOR CLEANING AN MAINTENANCE Welding and repair kit for parts in Corian. White ATMT003 CT Ecology System - water-repellent treatment kit. For marble, stone and terracotta. 0,5 lt AVBL

176 M i r r o r s WK6 - (esign Piero Lissoni) Customised mirror. A 200 min max. ice per square meter. 23 mm thick aluminium frame. Available versions: naturally anodised, matt white or matt black painted. Horizontal or vertical assembly possible. H min 200 mm / max 1200 mm. Min. possible size: 0,60 m² - For smaller mirrors the price has to be considered as that of the minimum size. A = vertical supporting piece. To L 900 mm: no pieces necessary / from L 901 to 1500 mm: 1 piece / from L 1501 to 3000 mm: 2 pieces. 200 min. 900 max. 910 min max min max. L from 200 to 900 mm OMAR11 L from 910 to 1500 mm OMAR12 L from 1510 to 3000 mm OMAR13 WK6 - (esign Piero Lissoni) Fixed-sized mirror. 23 mm thick aluminium frame. Available versions: naturally anodised, matt white or matt black painted. Horizontal or vertical assembly possible OMAR OMAR OMAR OMAR OMAR08 WK6 - (esign Piero Lissoni) Mirror with single LE bar. 190 H mm thick aluminium frame. Available versions: naturally anodised, matt white or matt black painted. Lighting: LE. Max. power: 18 W per linear metre. Colour temperature: 2700 K. Switch: on wall please arrange cable - centred positioned, and relative remote control. Voltage: V Hz (Europe/USA). It cannot be rotated. L Europe/USA version OMAL02 Europe/USA version OMAL03 Europe/USA version OMAL04 Europe/USA version OMAL05 18 WK6 - (esign Piero Lissoni) Mirror with double LE bar H 23 mm thick aluminium frame. Available versions: naturally anodised, matt white or matt black painted. Lighting: LE. Max. power: 18 W per linear metre. Colour temperature: 2700 K. Switch: dimmerable button with position LE. Voltage: V Hz (Europe/USA). It cannot be rotated. L Europe/USA version OMA01 Europe/USA version OMA02 Europe/USA version OMA03 Europe/USA version OMA04 Europe/USA version OMA

177 M i r r o r s WK6 - (esign Piero Lissoni) Mirror with LE bar + 2 BOCCIA lamps L H 23 mm thick aluminium frame. Available versions: naturally anodised, matt white or matt black painted. Bar light: LE - 18 W per linear metre. Colour temperature: 2700 K. BOCCIA light: LE Acrich 2 dimmerable 12 W (each). Colour temperature: 2700 K. LE switch: dimmerable button with position LE. Switch of BOCCIA: dimmerable button. rawn=left (S), mirrored=right (). It cannot be rotated. 230 V - 50 Hz, Europe OMA06 S- 110 V - 60 Hz, USA OMA11 S- 230 V - 50 Hz, Europe OMA07 S- 110 V - 60 Hz, USA OMA12 S- 230 V - 50 Hz, Europe OMA08 S- 110 V - 60 Hz, USA OMA13 S- 230 V - 50 Hz, Europe OMA09 S- 110 V - 60 Hz, USA OMA14 S- 230 V - 50 Hz, Europe OMA10 S- 110 V - 60 Hz, USA OMA15 S- SQUARE - (esign C.R.S. Boffi) Mirrored cabinet, single door Cabinet in anodised aluminium. Not recessed version: side panels in mirror finish. Recessed version: side panels in aluminium. Reversible door. Customisations are not feasible. H Not recessed version OSAC05 Recessed version OSAC06 Not recessed version OSAC07 Recessed version OSAC08 18 SQUARE - (esign C.R.S. Boffi) Mirrored cabinet, 2 doors. L 160 Cabinet in anodised aluminium. 2 internal shelves. Not recessed version: side panels in mirror finish. Recessed version: side panels in aluminium. Customisations are not feasible. 500 Not recessed version OSAC01 Recessed version OSAC02 Not recessed version OSAC03 Recessed version OSAC

178 M i r r o r s INEX - (esign Felicia Ferrone ) ouble-sided mirror. Ø Cylinder-shaped structure in satin stainless steel. Mirrors mounted on rotating support. Side 1: plane mirror ø 200 mm. Side 2: 2 x magnifying mirror ø 200 mm. Customisations are not feasible OIAB01 KAJA - (esign Peter Jamieson ) Mirror Very thick transparent plexiglas. Support in AISI 304 stainless steel. The reflected image may be slightly deformed or double Customisations are not feasible OJAQ01 VENEZIANA - (esign Piero Lissoni ) Customised mirror, type A ,5 ice per square meter. 160 mm. frame in bevelled mirror. Frame in black anodised aluminium. Horizontal or vertical assembly possible. L min 800 mm, max 1200 mm. H min 800 mm, max 1200 mm. A Min 0,64 m² - max 0,9 m² OVMC01 Min 0,91 m² - max 1,2 m² OVMC02 Min 1,21 m² - max 1,44 m² OVMC03 VENEZIANA - (esign Piero Lissoni ) Customised mirror, type B. B ,5 ice per square meter. 200 mm. frame in bevelled mirror. Frame in black anodised aluminium. Horizontal or vertical assembly possible. L min 1210 mm, max 2000 mm. H min 1210 mm, max 2400 mm Min 1,46 m² - max 1,82 m² OVMC04 Min 1,83 m² - max 2,28 m² OVMC05 Min 2,29 m² - max 2,70 m² OVMC06 Min 2,71 m² - max 3,09 m² OVMC07 Min 3,10 m² - max 3,40 m² OVMC08 Min 3,41 m² - max 3,80 m² OVMC09 Min 3,81 m² - max 4,20 m² OVMC10 Min 4,21 m² - max 4,80 m² OVMC

179 M i r r o r s LOTUS - (esign Naoto Fukasawa ) Back illuminated mirror. 57 Lighting: LE. Absorption: OKAT07 = 12 W / OKAT08 = 20 W / OKAT10 = 20 W / OKAT09 = 40 W. Switch: please arrange the remote control. Colour temperature: 2700 K. Voltage: V Hz (Europe/USA). Ø ,5 Europe/USA version OKAT07 Europe/USA version OKAT08 Europe/USA version OKAT10 Europe/USA version OKAT09 LOTUS - (esign Naoto Fukasawa ) Mirror without lighting. 25 Melamine-coated rear support. Ø , OKAS OKAS OKAS OKAS

180 M i r r o r s Silcover Wood Wood Selection Wood Exclusive SP14 - (esign neunzig design ) Back illuminated mirror + finished frame, th. 12 mm OQAL SILCOVER: all range colours WOO: Oak, grey graphite oak, Ash grey oak ONLY. WOO SELECTION: Core walnut ONLY. WOO EXCLUSIVE: Abonos oak. Lighting: LE, low consumption. Absorption: 1200x900 = 80 W / 1800x900 = 120 W / 900x1200 = 80 W. Switch: please arrange the remote control. Colour temperature: 2700 K. Voltage: V Hz (Europe/USA). 87 OQAL OQAL02 Europe/USA version OQAL01 Europe/USA version OQAL02 Europe/USA version OQAL03 SP14 - (esign neunzig design ) Back illuminated mirror + finished frame, th. 12 mm SILCOVER: all range colours. WOO: Oak, grey graphite oak, Ash grey oak ONLY. WOO SELECTION: Core walnut ONLY. WOO EXCLUSIVE: Abonos oak. Lighting: LE, low consumption. Absorption: 150 W. Switch: please arrange the remote control. Colour temperature: 2700 K. Voltage: V Hz (Europe/USA) Europe/USA version OQAL

181 M i r r o r s LELINE - (esign C.R.S. Boffi ). Customised horizontal mirror WITH SHELF, with single LE bar. 31 H 31 mm. thick aluminium frame. Available versions: naturally anodised, matt white or matt black painted. Lighting: LE. Voltage: 230 V - 50 Hz, Europe / 110 V - 60 Hz, USA. Max. power: 10 W per linear metre. Colour temperature: 2700 K. Switch: please arrange the remote control. Removable shelf, to be applied during the assembly. L ice per linear metre (for L size) - L min 900 mm / max 1800 mm - H min 500 mm / max 700 mm OLBA001 ice per linear metre (for L size) - L min 900 mm / max 1800 mm - H min 701 mm / max 900 mm OLBA002 LELINE - (esign C.R.S. Boffi ). Customised reversible mirror, with single LE bar. 31 H Lamp can be installed on top side and can rotate 90 (counter-clockwise or not). 31 mm. thick aluminium frame. Available versions: naturally anodised, matt white or matt black painted. Lighting: LE. Voltage: 230 V - 50 Hz, Europe / 110 V - 60 Hz, USA. Max. power: 10 W per linear metre. Colour temperature: 2700 K. Switch: please arrange the remote control. L 18 ice per linear metre (for L size) - L min 900 mm / max 3000 mm - H min 400 mm / max 650 mm OLBB001 ice per linear metre (for L size) - L min 900 mm / max 3000 mm - H min 651 mm / max 1200 mm OLBB

182 M i r r o r s SOLSTICE - (esign Piero Lissoni ) Oval mirror. 0 Rear support in black painted MF. Customisations are NOT feasible. uring the installation it can be rotated and fixed in the wished position NEW OSBV01 SOLSTICE - (esign Piero Lissoni ) Oval mirror. 600 Rear support in black painted MF. Customisations are NOT feasible. uring the installation it can be rotated and fixed in the wished position. SOLSTICE - (esign Piero Lissoni ) Oval mirror. 600 Rear support in black painted MF. Customisations are NOT feasible. uring the installation it can be rotated and fixed in the wished position NEW OSBV02 NEW OSBV

183 M i r r o r s SOLSTICE - (esign Piero Lissoni ) Triangular mirror. Rear support in black painted MF. Customisations are NOT feasible. uring the installation it can be rotated and fixed in the wished position NEW OSBG01 SOLSTICE - (esign Piero Lissoni ) Round mirror. Rear support in black painted MF. Customisations are NOT feasible. Ø0 18 NEW OSBT

184 M i r r o r s MERCURY - (esign Claesson - Koivisto - Rune ) Mirror. 25 mm thick stratified glass. Stainless steel frame. Customisations are not feasible AVAILABLE UNTIL STOCK LASTS OYAQ01 MERCURY - (esign Claesson - Koivisto - Rune ) Mirror. 25 mm thick stratified glass. Stainless steel frame. Customisations are not feasible AVAILABLE UNTIL STOCK LASTS OYAT01 STAGE - (esign Piero Lissoni ) Back illuminated mirror + frontal lamps T5 back lights, low consumption. Touch twilight switch. Globalux incandescent frontal lights, E27 (Europe) - E26 (US), max 60 W. Sensor touch switch and dimmer. S = lamps on left side, = lamps on right side. IP 21 AVAILABLE UNTIL STOCK LASTS 230 V - 50 Hz, Europe OGAL01 S- 110 V - 60 Hz, USA OGAL02 S- 230 V - 50 Hz, Europe OGAL03 S- 110 V - 60 Hz, USA OGAL04 S- 18 STAGE - (esign Piero Lissoni ) Back illuminated mirror + frontal lamps T5 back lights, low consumption. Touch twilight switch. Globalux incandescent frontal lights, E27 (Europe) - E26 (US), max 60 W. Sensor touch switch and dimmer. S = lamps on left side, = lamps on right side. IP 21 AVAILABLE UNTIL STOCK LASTS 230 V - 50 Hz, Europe OGAL05 S- 110 V - 60 Hz, USA OGAL06 S- 230 V - 50 Hz, Europe OGAL07 S- 110 V - 60 Hz, USA OGAL08 S

185 A c c e s s o r i e s RL 11 (esign Ludovica and Roberto Palomba ) Accessories in enamelled white polished ceramic. RL 11 - Soap holder. RL 11 - Soap holder Polished white, top-mounted..... KERSA01 Polished white, wall-mounted..... KERSA02 RL 11 - Toothbrush holder. RL 11 - Towel holder Polished white, top-mounted..... Polished white, wall-mounted.... KERSP01 KERSP02 Polished white, wall-mounted. L Polished white, wall-mounted. L KERSV01 KERSV02 RL 11 - Toilet roll holder. RL 11 - Toilet brush holder Polished white, wall-mounted..... KERRT01 Polished white, top-mounted..... Polished white, wall-mounted KERSC01 KERSC

186 A c c e s s o r i e s RL 11 (esign Ludovica and Roberto Palomba ) Accessories in enamelled white polished ceramic. RL 11 - Shelf. RL 11 - Clothes hook Polished white, wall-mounted..... KERME01 Polished white, wall-mounted..... KERBT01 RL 11 - Storage tray Polished white, top-mounted..... KERGG

187 A c c e s s o r i e s MINIMAL (esign Giulio Gianturco ) Accessories in AISI 304 stainless steel, satin finish. MINIMAL - Soap holder. MINIMAL - Soap holder Satin stainless steel, top-mounted.... KIMSA01 Satin stainless steel, wall-mounted.... KIMSA02 MINIMAL - Glass for toothbrush holder. MINIMAL - Toilet roll holder White ceramic insert. Ø70 Satin stainless steel, floor-mounted or wall-mounted. KIMSP01 Satin stainless steel, wall-mounted.... KIMRT01 MINIMAL - Towel holder. 80 MINIMAL - Toilet brush holder Ø 70 White ceramic insert. Satin stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L KIMSV01 KIMSV02 KIMSV03 Satin stainless steel, floor-mounted or wall-mounted. KIMSC

188 A c c e s s o r i e s MINIMAL (esign Giulio Gianturco ) Accessories in AISI 304 stainless steel, satin finish. MINIMAL - Extendable magnifying mirror. MINIMAL - Bathrobe hook. Ø min. 150 max. 650 With aluminium frame. One side is a regular mirror, and the reverse side provides 2X magnification. Extends min. 150 mm, max 650 mm from the wall. 2 piece package. Satin stainless steel, wall-mounted.... KIMSE01 Satin stainless steel, wall-mounted.... KIMBT01 MINIMAL - Single bathrobe hook. MINIMAL - Multiple bathrobe hook Ø piece package. Wall-foldable. Satin stainless steel, wall-mounted.... KIMBT02 Satin stainless steel, wall-mounted.... KIMBT03 MINIMAL - Holder for spare toilet roll. MINIMAL - Newspaper holder Ø30 40 AVAILABLE UNTIL STOCK LASTS Satin stainless steel, wall-mounted.... KIMBT04 Satin stainless steel, wall-mounted.... KIMRV

189 A c c e s s o r i e s MINIMAL (esign Giulio Gianturco ) Accessories in AISI 304 stainless steel, satin finish. MINIMAL - Towel rack. MINIMAL - Free-standing towel holder Shelf in solid grey graphite oak. Satin stainless steel, wall-mounted.... KIMSV04 Satin stainless steel, top-mounted.... KIMSV06 MINIMAL - Vertical towel rail. MINIMAL - Free-standing towel holder Satin stainless steel, wall-mounted.... KIMSV05 Satin stainless steel, top-mounted.... KIMSV08 MINIMAL - Laundry-sack. MINIMAL - Soap dispenser Optional accessory for towel holder code KIMSV White ERLIN. Ø60 Fabric.... KIMPB01 Satin stainless steel, top-mounted.... KIMS

190 A c c e s s o r i e s MINIMAL (esign Giulio Gianturco ) Accessories in AISI 304 stainless steel, satin finish. MINIMAL - Foldable clothes-drier FOR 4 coat hangers Coat hangers excluded. Satin stainless steel..... KIMS

191 A c c e s s o r i e s TWIG (esign Keiji Takeuchi ) Accessories in Iroko solid wood, white Cristalplant and stainless steel treated with PV coating technology or painted. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. TWIG - Soap holder. TWIG - Tray Made of white Cristalplant. Anti-slip bottom made of EPM rubber. Made of white Cristalplant. Anti-slip bottom made of EPM rubber. White..... KPWSA01 White..... KPWVA01 TWIG - Toothbrush holder. TWIG - Soap holder Made of white Cristalplant. Anti-slip bottom made of EPM rubber. Soap dish in white Cristalplant. Support in Iroko solid wood. White..... KPWSP01 White + Iroko, wall-mounted..... KPWSA02 TWIG - Shelf. TWIG - Towel holder Shelf in white Cristalplant. Support in Iroko solid wood. Rod for towel in solid Iroko wood. Supports in stainless steel, treated with grey PV technology. White + Iroko, wall-mounted..... KPWME01 19,3 Grey PV + Iroko wood, wall-mounted - L 300 mm. Grey PV + Iroko wood, wall-mounted - L 400 mm.. Grey PV + Iroko wood, wall-mounted - L 600 mm.. KLWSV01 KLWSV02 KLWSV

192 A c c e s s o r i e s TWIG (esign Keiji Takeuchi ) Accessories in Iroko solid wood, white Cristalplant and stainless steel treated with PV coating technology or painted. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. TWIG - Free standing towel holder. TWIG - Toilet brush holder Rods in solid Iroko wood.base in stainless steel treated with grey PV technology Anti-slip bottom made of EPM rubber. 275 Body in stainless steel, matt white painted. Handle in solid Iroko wood. 85 Grey PV + Iroko wood..... KLWSV05 White + Iroko, floor- or wall-mounted.... KVWSC01 TWIG - Toilet roll holder. TWIG - Toilet roll holder with towel holder Support in stainless steel, treated with grey PV technology. Rod in solid Iroko wood. Support in stainless steel, treated with grey PV technology. Rod in solid Iroko wood. Grey PV + Iroko wood..... KLWRT01 Grey PV + Iroko wood..... KLWSV04 TWIG - Clothes hook. TWIG - Coat hanger Made of Iroko solid wood. Made of Iroko solid wood. Hook in leather. Iroko wood..... KLWBT01 Iroko wood..... KLWGR

193 A c c e s s o r i e s TWIG (esign Keiji Takeuchi ) Accessories in Iroko solid wood, white Cristalplant and stainless steel treated with PV coating technology or painted. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. TWIG - Small table Top in white Cristalplant. Leg in solid Iroko wood. Base in stainless steel treated with grey PV technology White + Iroko + grey PV..... KPWAV

194 A c c e s s o r i e s BLAE (esign Gianluigi Landoni ) Accessories in AISI 304 stainless steel, th. 4 mm - Polished / satin / grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. BLAE - Soap holder. BLAE - Soap holder ish in teak wood. ish in teak wood. Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBSA01 KIBSA03 KIBSA05 Polished stainless steel, top-mounted..... Satin stainless steel, top-mounted..... Grey PV, top-mounted.... KIBSA02 KIBSA04 KIBSA06 BLAE - Toothbrush holder. BLAE - Glass for toothbrush holder. 94 Ø Glass in pyrex glass. Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBSP01 KIBSP02 KIBSP03 Pyrex glass, top-mounted..... KOBSP01 BLAE - Towel holder. BLAE - Towel holder L 19 Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBSV05 KIBSV12 KIBSV17 Polished stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L Grey PV, wall-mounted. L Polished stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L Grey PV, wall-mounted. L KIBSV04 KIBSV11 KIBSV15 KIBSV03 KIBSV10 KIBSV

195 A c c e s s o r i e s BLAE (esign Gianluigi Landoni ) Accessories in AISI 304 stainless steel, th. 4 mm - Polished / satin / grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. BLAE - Towel holder. BLAE - Toilet roll holder L 24 Polished stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L Grey PV, wall-mounted. L Polished stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L Grey PV, wall-mounted. L KIBSV02 KIBSV09 KIBSV18 KIBSV01 KIBSV08 KIBSV19 Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBSV06 KIBSV13 KIBRT01 BLAE - Clothes hook BLAE - Clothes hook Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBBT01 KIBBT03 KIBBT05 Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBBT02 KIBBT04 KIBBT06 BLAE - Shower shelf. BLAE - Shelf L 19 Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBME01 KIBME05 KIBME09 Polished stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L Grey PV, wall-mounted. L Polished stainless steel, wall-mounted. L Satin stainless steel, wall-mounted. L Grey PV, wall-mounted. L KIBME02 KIBME06 KIBME10 KIBME03 KIBME07 KIBME

196 A c c e s s o r i e s BLAE (esign Gianluigi Landoni ) Accessories in AISI 304 stainless steel, th. 4 mm - Polished / satin / grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. BLAE - Corner shower shelf. BLAE - Toilet brush holder Ø Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... Grey PV, wall-mounted.... KIBME04 KIBME08 KIBME12 Polished stainless steel, floor-mounted or wall-mounted. KIBSC01 Satin stainless steel, floor-mounted or wall-mounted..... KIBSC02 Grey PV, wall-mounted.... KIBSC03 BLAE - Towel rack. BLAE - Soap dish in teak wood. 274 P Small version: it can be used as spare part for cod. KIBSA Big version: it can be used with cod. KIBME Polished stainless steel, wall-mounted.... Satin stainless steel, wall-mounted..... KIBSV07 KIBSV14 Small, top-mounted.... Big, top-mounted..... KABAP01 KABAP02 BLAE - Waste bin. BLAE - Tissue box holder Ø153 Swing lid. Polished stainless steel, top-mounted..... Satin stainless steel, top-mounted..... KIBRF01 KIBRF02 Polished stainless steel, top-mounted..... Satin stainless steel, top-mounted..... KIBKL01 KIBKL

197 A c c e s s o r i e s BLAE (esign Gianluigi Landoni ) Accessories in AISI 304 stainless steel, th. 4 mm - Polished / satin / grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. BLAE - Makeup pads holder. 200 Ø64 Polished stainless steel, top-mounted..... Satin stainless steel, top-mounted..... KIBMU01 KIBMU

198 A c c e s s o r i e s PIPE (esign Marcel Wanders ) Accessories in AISI 304 stainless steel. PIPE - Toilet roll holder. PIPE - Towel holder. 36,5 Ø Ø16 Ø88 Ø119 etails in red. etails in red. Satin stainless steel + red.... KIPRT01 Satin stainless steel + red.... KIPSV01 PIPE - Clothes hook. 41,5 Ø16 Ø69 etails in red. Satin stainless steel + red.... KIPBT

199 A c c e s s o r i e s SHORTCUT (esign Nendo ) Accessories in AISI 304 stainless steel, matt white finish, diameter 10 mm. Varnished with epoxy powder. SHORTCUT - Towel holder. SHORTCUT - Towel holder White, L White, L KESSV01 KESSV02 White..... KESSV

200 A c c e s s o r i e s SKYLINE (esign neunzig design ) Accessories in white Corian. The single configurations cannot be changed. Wall-mounted cabinet with 2 compartments. Wall-mounted cabinet with 3 compartments White..... KNYBX02 White..... KNYBX01 Floor-mounted basement with 3 compartments White..... KNYBY

201 A c c e s s o r i e s IKO (esign Kensaku Oshiro ) Accessories in AISI 304 satin stainless steel rod, diameter 12 mm. Base in Serena stone. IKO - Tall free-standing towel holder. IKO - Short free-standing towel holder ø120 ø120 Stainless steel, floor-mounted.... KIISV01 Stainless steel, floor-mounted.... KIISV02 IKO - Free-standing toilet roll holder. 210 ø ø120 Stainless steel, floor-mounted.... KIIRT

202 W a s h b a s i n s TOP-MOUNTE Top-mounted. Please consider to add a cut-out on top (top-mounted washbasin), cod. ZNBA09. A45 - (esign Victor Vasilev ) Washbasin in Cristalplant, without overflow Optional drain-hole covering shelf, to be ordered separately. SUSPENE version available too: please order separately the supporting brackets. Compatible siphon (to be ordered separately): ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. Certifications: USA - Canada. 900 White WRAQAE01 A45 STONE - (esign Victor Vasilev ) Washbasin in marble, without overflow Optional drain-hole covering shelf, to be ordered separately. SUSPENE version available too: please order separately the supporting brackets. Compatible siphon (to be ordered separately): ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. The stone parts are treated with water- and oil-repellent products. 900 White Carrara marble WMAQAE01 A45 COMPACT - (esign Victor Vasilev ) Washbasin in Cristalplant, without overflow. 125 SUSPENE version available too: please order separately the supporting brackets. Compatible siphon (to be ordered separately): ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. Certifications: USA - Canada White WRAQAE02 A45 - (esign Victor Vasilev ) rain-hole covering shelf. Available versions: Cristalplant / solid Canaletto walnut. White Cristalplant WRAQAV01 Solid wood WLAQAV01 A45 - (esign Victor Vasilev ) Pair of supporting brackets. Painted metal. Only for wall assembly. For the A45 STONE washbasin please order the specific brackets. 20 NEW A AVBF004 A45 STONE AVBF

203 W a s h b a s i n s TOP-MOUNTE Top-mounted. Please consider to add a cut-out on top (top-mounted washbasin), cod. ZNBA09. CANALE Washbasin in Cristalplant, with overflow. L Basin position: reversible / imensions: L P H. Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. Certifications: USA - Canada. White, L from 1200 to 1600 mm WRCNAE01 White, L from 1601 to 2000 mm WRCNAE02 White, L from 2001 to 2400 mm WRCNAE03 CATHINO 1 CERAMILUX - (esign Piero Lissoni ) Washbasin in Ceramilux, without overflow. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. Certifications: USA - Canada Glossy-white WXCHAE01 Matt white WXCHAE03 CATHINO 3 CERAMILUX - (esign Piero Lissoni ) Washbasin in Ceramilux, without overflow. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. Certifications: USA - Canada Glossy-white WXCHAE02 Matt white WXCHAE04 20 FISHER ISLAN - (esign Piero Lissoni ) Washbasin in Cristalplant, without overflow Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Certifications: USA - Canada. 138 Matt white WRAFAE01 White + Soft Touch grey WSAFAE

204 W a s h b a s i n s TOP-MOUNTE Top-mounted. Please consider to add a cut-out on top (top-mounted washbasin), cod. ZNBA09. ICELAN - (esign Piero Lissoni ) Washbasin in Cristalplant, without overflow. 430 Available versions: totally white / white + Soft touch grey. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada White WRICAE01 White + Soft Touch grey WSICAE01 SABBIA 3 - (esign Naoto Fukasawa ) Washbasin in Cristalplant, without overflow Available versions: totally white / white + Soft touch grey. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada. GAREN - (esign Piero Lissoni ) Washbasin in stainless steel, without overflow To be completed with drain-hole covering shelf cod. WMGAAV01 / WNGAAV01. AISI 304 stainless steel sheet, grey PV finish. PV: Physical vapour eposition. When used on WOO-IN tops for GAREN washbasin please add only the top-mounted cut-out cod. ZNBA09 for cabinet. The top includes already the washbasin cut-out. Compatible siphon (to be ordered separately): ANBM002 chromium-plated / ANBM006 stainless steel / ANBM016 grey PV. Compatible waste drain (to be ordered separately): ANHG001 stainless steel. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Grey PV WBGAAE01 Stone A Stone B Stone C Stone Stone E Corian 500 White WRSBAC01 White + Soft Touch grey WSSBAC01 GAREN - (esign Piero Lissoni ) rain-hole covering shelf. Versions: stone, marble, granite / Corian. The internal bottom cover of the GAREN washbasin in STONE, MARBLE, GRANITE finish is cut-out from the same sheet of the top, to guarantee a continuous grain (ONLY when it s ordered together with WOO-IN top for Garden washbasin). Stone A: available ONLY in white CARRARA marble. Stone B: available ONLY in Cardoso stone. Stone C: available ONLY in QUARTZITE SILVER. Stone : available ONLY in Emperador ark marble / Black Cosmic granite. Stone E: available ONLY in GREY STONE marble / Quartzite Calacatta. 20 Stone - Marble - Granite WMGAAV01 White Corian WNGAAV

205 W a s h b a s i n s TOP-MOUNTE Top-mounted. Please consider to add a cut-out on top (top-mounted washbasin), cod. ZNBA09. LOTUS - (esign Naoto Fukasawa ) Washbasin in Cristalplant, without overflow. Ø A top-mounted mirror (max thickness: 25 mm) can be positioned on the rear part of FLYER suspended tops ONLY. SUSPENE version available too: please order separately the supporting structure WILSSS01. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 chromium-plated / ANHR004 stainless steel. Certifications: USA - Canada. Ø 520 White Cristalplant WRLSAE01 LOTUS - (esign Naoto Fukasawa ) Supporting structure for washbasin. 15 AISI 304 stainless steel sheet. Only for wall assembly Stainless steel WILSSS01 L10 - (esign Norbert Wangen ) Washbasin in solid marble, without overflow Satin finish. Rear space in case of tap hole necessity. SUSPENE version available too: please order separately the supporting structure. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. The stone parts are treated with water- and oil-repellent products. 700 Statuary white WMLAE01 Marquinia black WMLAE02 20 L10 - (esign Norbert Wangen ) Supporting structure. Only for wall assembly. Totally concealed (in the washbasin thickness). Satin stainless steel WILSS

206 W a s h b a s i n s TOP-MOUNTE Top-mounted. Please consider to add a cut-out on top (top-mounted washbasin), cod. ZNBA09. AA - (esign Claudio Silvestrin ) Washbasin in Corian, with overflow. Ø 500 Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. 170 White WNAAE01 GOBI 1 - (esign Marcel Wanders ) Washbasin in Cristalplant, with overflow Available versions: totally white / white + Soft touch grey. SUSPENE version available too: please order separately the supporting structure. Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada. White WRGBAE01 White + Soft Touch grey WSGBAE01 GOBI 2 - (esign Marcel Wanders ) Washbasin in Cristalplant, with overflow Available versions: totally white / white + Soft touch grey. SUSPENE version available too: please order separately the supporting structure. Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada AVAILABLE UNTIL STOCK LASTS White WRGBAE02 White + Soft Touch grey WSGBAE02 GOBI - (esign Marcel Wanders ) Supporting structure. 115 L Only for wall assembly. With hole for single-hole tap. A cover for tap hole is provided (in case of wall-mounted tap) AVAILABLE UNTIL STOCK LASTS Satin stainless steel, for GOBI WIGBSS01 Satin stainless steel, for GOBI WIGBSS

207 W a s h b a s i n s TOP-MOUNTE Top-mounted. Please consider to add a cut-out on top (top-mounted washbasin), cod. ZNBA09. AIGE - (esign Claudio Silvestrin ) Washbasin in solid stone, without overflow The stone parts are treated with water- and oil-repellent products. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. 170 Serena stone WMAGAF04 PIAVE - (esign Claudio Silvestrin ) Washbasin in solid stone, without overflow. Ø Ø 460 To be used with FLYER suspended tops, P. 600 mm. The stone parts are treated with water- and oil-repellent products. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. Ø Serena stone WMPVA

208 W a s h b a s i n s BUILT-IN Built-in. Please consider to add a cut-out on top (top-mounted washbasin), cod. ZNBA09. SABBIA BTM Washbasin in Cristalplant, without overflow NEW Finished visible perimeter edge H 12 mm. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Certifications: USA - Canada. 615 White WRSBAF

209 W a s h b a s i n s UNER-MOUNTE Under-mounted. Please consider to add an under top cut-out (under-mounted washbasin), cod. ZNBA10. The washbasin cut-out and gluing is included when tops are in CRISTALPLANT. For tops in STONE, MARBLE, GRANITE, COMPOSITE please consider to add under top cut-out (gluing supplied by the Customer), cod. ZNBA10 For tops in GLASS please consider to add the under top cut-out cod. ZNBA10 and the price for gluing cod. ZNB07. UNIVERSAL small Washbasin in Cristalplant, with overflow Compatible with tops in Cristalplant, stone, marble, granite, composite, glass. Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. The washbasin cut-out and gluing is included when tops are in Cristalplant. Certifications: USA - Canada White WRUNAB03 UNIVERSAL big Washbasin in Cristalplant, with overflow The washbasin cut-out and gluing is included when tops are in Cristalplant. Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. Compatible with tops in Cristalplant, stone, marble, granite, composite, glass. Certifications: USA - Canada. 753 White WRUNAB02 SIEL 2 - (esign Piero Lissoni ) Washbasin in Cristalplant, with overflow The washbasin cut-out and gluing is included when tops are in Cristalplant. Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. Certifications: USA - Canada. 555 Ø AVAILABLE UNTIL STOCK LASTS White WRCAB01 Stone A Stone B Stone C Stone Stone E 20 PIETRA Washbasin in stone, marble, granite, composite. = 282 = / 700 = = Compatible ONLY with tops in stone, marble, granite or composite. Compatible with FLYER and PIANURA suspended tops too: please note that the external visible sides are in stainless steel. Without overflow, waste free flow. With plug covered in the same finish as washbasin. NOT FEASIBLE in EKTON. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR004 stainless steel. The stone parts are treated with water- and oil-repellent products / 780 Small WAPTAB01 Big WAPTAB

210 W a s h b a s i n s MOULE FLUSH-MOUNTE Moulded washbasins, recessed at the same level of the top. O NOT add the cut-out for washbasin: the price includes the washbasin and the moulding process. KUPA - (Victor Vasilev ). Moulded flush-mounted washbasin in Cristalplant, without overflow Compatible ONLY with 15 mm thick tops in Cristalplant or mm thick XILA BATH tops. The price includes the washbasin or the moulding process. O NOT add the washbasin cut-out. Compatible siphon (to be ordered separately): ANBM002 chromium-plated / ANBM006 stainless steel. Cover for strainer waste in Cristalplant included. Certifications: USA - Canada. 700 White WZKPAJ001 SABBIA 1 - (esign Naoto Fukasawa ) Moulded flush-mounted washbasin in Cristalplant, without overflow Compatible ONLY with 15 mm thick tops in Cristalplant. The price includes the washbasin and the moulding process. O NOT add the washbasin cut-out. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Certifications: USA - Canada. 480 White WRSBAB01 SABBIA 2 - (esign Naoto Fukasawa ) Moulded flush-mounted washbasin in Cristalplant, without overflow Compatible ONLY with 15 mm thick tops in Cristalplant. The price includes the washbasin and the moulding process. O NOT add the washbasin cut-out. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Certifications: USA - Canada. 600 White WRSBAB02 SABBIA 6 - (esign Naoto Fukasawa ) Moulded flush-mounted washbasin in Corian, without overflow Compatible ONLY with PIANURA, FLYER and I FIUMI ST tops in Corian. The price includes the washbasin and the moulding process. O NOT add the washbasin cut-out. Set of compatible waste drain + siphon (to be ordered separately): ANHR005 white+chromium-plated / ANHR006 white+stainless steel. 480 White ZTRBK01 SABBIA 7 - (esign Naoto Fukasawa ) Moulded flush-mounted washbasin in Corian, without overflow Compatible ONLY with PIANURA, FLYER and I FIUMI ST tops in Corian. The price includes the washbasin and the moulding process. O NOT add the washbasin cut-out. Set of compatible waste drain + siphon (to be ordered separately): ANHR005 white+chromium-plated / ANHR006 white+stainless steel. When used on PIANURA with chromium-plated siphon kit cod. ANHR005 is necessary to order separately the chromium-plated extension cod. ANHI White ZTRBK

211 W a s h b a s i n s SUSPENE Wall-mounted. For the suspended versions of washbasins GOBI 1 (WRGBAE01) - GOBI 2 (WRGBAE02) - L10 (WMLAE01/2) - A45 (WRAQAE01) - LOTUS(WRLSAE01) please see the TOP-MOUNTE washbasins (please order the washbasin and separately the supporting structures). CANALE Monobloc washbasin in Cristalplant, with overflow. L Basin dimensions: L P H mm. Versions: basin on left (S) or on right (). Set of compatible waste drain + siphon (to be ordered separately): ANHH001 chromium-plated / ANHR001 stainless steel. Optional tap holes, to be ordered separately. Certifications: USA - Canada. White, L from 1200 to 1600 mm WRCNA01 S- White, L from 1601 to 2000 mm WRCNA02 S- White, L from 2001 to 2400 mm WRCNA03 S- PHW CERAMILUX - (esign Piero Lissoni ). Washbasin in Ceramilux, without overflow. 160 Ø Optional tap hole (to be ordered separately). Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. Certifications: USA - Canada. 450 Ø 400 Ø Ø35 Glossy-white WXPHAA01 Matt white WXPHAA03 20 PHW - (esign Piero Lissoni) Washbasin in Corian, without overflow. 80 Ø 400 rain-hole covering insert in Corian and stainless steel supporting bracket. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel Ø Ø White, without rear space - for tap positioning - and tap hole WNPHAA01 White, with rear space - for tap positioning - and 1 tap hole WNPHAA

212 W a s h b a s i n s WITH COLUMN Wall-mounted or free-standing washbasins. PHC - (esign Piero Lissoni ) Washbasin in Corian, without overflow. 374 Wall-mounted. rain-hole covering insert in Corian. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel White, wall-mounted WNPHAG01 PHC - (esign Piero Lissoni ) Washbasin in Cristalplant, without overflow. 374 Wall-mounted. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Available versions: white / white + Soft touch grey. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada. 900 NEW 400 White, wall-mounted WRPHAG01 White + Soft Touch grey, wall-mounted WSPHAG01 PHC - (esign Piero Lissoni ) Washbasin in Cristalplant, without overflow free-standing. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Available versions: white / white + Soft touch grey. Soft Touch: coating made of anthracite grey paint. With set of floor-fixed connecting pipes. Certifications: USA - Canada. 20 NEW 400 White, free-standing WRPHAG02 White + Soft Touch grey, free-standing WSPHAG

213 W a s h b a s i n s WITH COLUMN Wall-mounted or free-standing washbasins. Stone A Stone PH STONE - (esign Piero Lissoni ) Washbasin in stone, without overflow Wall-mounted. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. With plug covered in the same finish as washbasin. The stone parts are treated with water- and oil-repellent products. Stone A: available ONLY in white Carrara marble / Serena stone. Stone : available ONLY in Emperador ark marble. Weight without water: 155 kg. 400 NEW Wall-mounted WMPHAG01 PH STONE - (esign Piero Lissoni ) Washbasin in stone, without overflow free-standing. Set of compatible waste drain + siphon (to be ordered separately): ANHH002 chromium-plated / ANHR002 stainless steel. With plug covered in the same finish as washbasin. The stone parts are treated with water- and oil-repellent products. With set of floor-fixed connecting pipes. Stone A: available ONLY in white Carrara marble / Serena stone. Stone : available ONLY in Emperador ark marble. Weight without water: 155 kg. 400 NEW Free-standing WMPHAG

214 W a s h b a s i n s WITH COLUMN Wall-mounted or free-standing washbasins. SABBIA 4 - (esign Naoto Fukasawa ) Washbasin in Cristalplant, without overflow Wall-mounted. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Available versions: white / white + Soft touch grey. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada. SABBIA 4 SABBIA 5 - (esign Naoto Fukasawa ) Washbasin in Cristalplant, without overflow. free-standing. With set of floor-fixed connecting pipes. Available versions: white / white + Soft touch grey. Set of compatible waste drain + siphon (to be ordered separately): ANHR003 white+chromium-plated / ANHR004 white+stainless steel. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada White, wall-mounted WRSBAG02 White + Soft Touch grey, wall-mounted WSSBAG SABBIA White, free-standing WRSBAG01 White + Soft Touch grey, free-standing WSSBAG

215 B a t h t u b s TEVERE - (esign Claudio Silvestrin ) Monobloc bathtub. Ø In white thermoformed Corian. Boxed in wooden crate. Equipped with stainless steel waste drain, siphon and overflow. Weight without water: 300 kg - Water capacity: 600 ltr. 550 Ø 1 White QAVISP01 TERRA - (esign Naoto Fukasawa ) Monobloc bathtub A - B In white Cristalplant. Boxed in wooden crate. Equipped with chromium-plated waste drain, siphon and overflow. Water supply from bathtub edge. Weight without water: 210 kg - Water capacity: 400 ltr. Available without tap hole arrangement / or with tap hole and stainless steel tap (including mixer and hand-shower with its mixer). Certifications: USA - Canada. B A 1700 White. Without tap hole arrangement QARISR01 White. With lateral hole and tap, A side position QARISR04 White. With lateral hole and tap, B side position QARISR05 ICELAN - (esign Piero Lissoni ) Monobloc bathtub In white Cristalplant. Boxed in wooden crate. Equipped with chromium-plated waste drain, siphon and overflow. Weight without water: 160 kg - Water capacity: 380 ltr. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada. 480 White QAIISR01 White + Soft Touch grey QAIISS01 SABBIA - (esign Naoto Fukasawa ) Monobloc bathtub In white Cristalplant. Boxed in wooden crate. Equipped with chromium-plated waste drain, siphon and overflow. Weight without water: 163 kg - Water capacity: 310 ltr. Certifications: USA - Canada White QAYISR

216 B a t h t u b s FISHER ISLAN - (esign Piero Lissoni + C.R.S. Boffi ) Monobloc bathtub White Ceramilux, matt. Crated in a wooden case. Equipped with chromium-plated waste drain, siphon and overflow. Weight without water: 98 kg - Water capacity: 290 ltr. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada. 475 White QAFISX02 White + Soft Touch grey QAFISS01 Stone A Stone FISHER ISLAN STONE - (esign Piero Lissoni + C.R.S. Boffi ) Monobloc bathtub Stone A: available ONLY in white Carrara marble / Serena stone. Stone : available ONLY in Emperador ark marble. In solid natural stone. Boxed in wooden crate. Weight without water: 400 kg - Water capacity: 290 ltr. Please order separately the waste-drain with overflow in the finish wished: ANBN011 chromium-plated, ANBN012 stainless steel, ANBN013 PV. NEW QAFISM01 21 Headrest for bathtub Made of white silicone rubber. Compatible with all Boffi bathtubs, SABBIA and FISHER ISLAN excluded. It adjusts to the bathtub shape. To be placed and fixed with adhesive tape positioned on the lower part ANMT

217 B a t h t u b s GOBI SMALL SIZE - (esign Marcel Wanders ) Monobloc bathtub In white Cristalplant. Boxed in wooden crate. Equipped with chromium-plated waste drain, siphon and overflow. Weight without water: 170 kg - Water capacity: 305 ltr. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada AVAILABLE UNTIL STOCK LASTS White QAGISR02 White + Soft Touch grey QAGISS

218 B a t h t u b s I FIUMI series (esign Claudio Silvestrin ) PO (Stone) Monobloc bathtub / 2 In solid natural stone. Boxed in wooden crate. Equipped with stainless steel waste drain, siphon and overflow. Weight without water: ca. 800 kg (QAPISM04) - ca. 900 kg (QAPISM05). Water capacity: 320 ltr SERENA stone QAPISM04 SERENA stone QAPISM05 PO (Corian ) Monobloc bathtub In thermoformed Corian. Boxed in wooden crate. Equipped with stainless steel waste drain, siphon and overflow. Weight without water: 150 kg. Water capacity: 320 ltr White QAPISP

219 B a t h t u b s SWIM C series (esign Piero Lissoni ) Technical features / typologies. Bathtub in Cristalplant with double backrest slope. Water capacity: 325 ltr. Versions: BUILT-IN - FREE-STANING WITH PANELS - PENINSULA WITH PANELS - CORNER WITH PANELS - NICHE WITH PANELS - WITH OPEN-FACE COM- PARTMENTS. BUILT-IN: upper/under-mounted installation, for walling and panelling supplied by the customer. Available in 4 sizes or customised. FREE-STANING WITH PANELS: free-standing installation, with fixed panels in Cristalplant glued on 4 sides. Available in 4 sizes or customised. PENINSULA WITH PANELS: peninsula installation, with longer side against the wall and fixed panels in Cristalplant glued on other 3 sides. Available in 4 sizes or customised. CORNER WITH PANELS: for corner installation, with fixed panels in Cristalplant glued on 2 sides. Available in 4 sizes or customised. NICHE WITH PANELS: for niche installation, with fixed panel in Cristalplant glued on 1 side. Available in 4 sizes or customised. WITH OPEN-FACE COMPARTMENTS: for free-standing, peninsula, corner or niche installation. The sides without compartments have a glued fixed panel in Cristalplant. The sides with compartments are in finish. Available in 4 versions, in accordance to the number of sides with open-faced compartments. The peninsula, niche and corner bathtubs can be installed free-standing too, thanks to the use of finished panels fixed on sides without compartments. Open-faced compartments available in: Wood - Selection Wood - Ecolak - Wood Exclusive. Certifications: USA - Canada

220 B a t h t u b s SWIM C series (esign Piero Lissoni ) BUILT-IN bathtub. BUILT-IN bathtub. - Technical chart P1 P3 P2 P P1 P3 P2 P X 21 Y min 790 / max 1250 X1 min 1750 / max 2050 P1 P2 P3 P X2 Y1 690 Y2 min 50 / max 280 min 50 / max Customised. 425 min 50 / max 200 min 50 / max 200 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. The customised bathtub must have on the order the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted. 21.8

221 B a t h t u b s SWIM C series (esign Piero Lissoni ) BUILT-IN bathtub. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Upper/under-mounted installation, walling and panelling supplied by the customer. BUILT-IN bathtub White QAWSSR White QAWSSR White QAWSSR White QAWSSR04 Y1 500 X 1650 Y 690 Y2 X1 Feasible sizes: X = min 1750 mm, max 2050 mm / Y = min 790 mm, max 1250 mm. X1 and X2 = min 50 mm, max 200 mm. / Y1 and Y2 = min 50 mm, max 280 mm. In the order please ALWAYS specify the right X, Y, X1, X2, Y1, Y2 dimensions. The X1, X2, Y1 and Y2 sizes can be different from each other, considering always the min. and max. allowed dimensions. With deck-mounted tap, Y1 or Y2 min. mm. 21 X2 White, CUSTOMISE SIZE QAWSSR

222 B a t h t u b s SWIM C series (esign Piero Lissoni ) FREE-STANING bathtub WITH PANELS. FREE-STANING bathtub WITH PANELS. - Technical chart P1 P3 P2 P P1 P3 P2 P X 21 Y min 830 / max 1250 X1 min 1790 / max 2050 P1 P2 P3 P X2 Y1 690 Y2 min 70 / max 280 min 70 / max Customised. 425 min 70 / max 200 min 70 / max 200 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. The customised bathtub must have on the order the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted

223 B a t h t u b s SWIM C series (esign Piero Lissoni ) FREE-STANING bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 4 sides. FREE-STANING bathtub WITH PANELS White QAWISR White QAWISR White QAWISR White QAWISR04 Y1 500 X Y Y2 X1 Feasible sizes: X = min 1790 mm, max 2050 mm / Y = min 830 mm, max 1250 mm. X1 and X2 = min 70 mm, max 200 mm. / Y1 and Y2 = min 70 mm, max 280 mm. In the order please ALWAYS specify the right X, Y, X1, X2, Y1, Y2 dimensions. The X1, X2, Y1 and Y2 sizes can be different from each other, considering always the min. and max. allowed dimensions. With deck-mounted tap, Y1 or Y2 min. mm. 21 X2 White, CUSTOMISE SIZE QAWISR

224 B a t h t u b s SWIM C series (esign Piero Lissoni ) PENINSULA bathtub WITH PANELS. PENINSULA bathtub WITH PANELS. - Technical chart P1 P3 P2 P P1 P3 P2 P X 21 Y min 790 / max 1250 X1 min 1750 / max 2050 P1 P2 P3 P X2 Y1 690 Y2 min 50 / max 280 min 50 / max Customised. 425 min 50 / max 200 min 50 / max 200 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. The customised bathtub must have on the order the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted

225 B a t h t u b s SWIM C series (esign Piero Lissoni ) PENINSULA bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 3 sides. The longer side with overflow is always against the wall. PENINSULA bathtub WITH PANELS White QAWPER White QAWPER White QAWPER White QAWPER04 Y1 500 X Y Y2 X1 Feasible sizes: X = min 1750 mm, max 2050 mm / Y = min 790 mm, max 1250 mm. X1 and X2 = min 50 mm, max 200 mm. / Y1 and Y2 = min 50 mm, max 280 mm. In the order please ALWAYS specify the right X, Y, X1, X2, Y1, Y2 dimensions. The X1, X2, Y1 and Y2 sizes can be different from each other, considering always the min. and max. allowed dimensions. With deck-mounted tap, Y1 or Y2 min. mm. 21 X2 White, CUSTOMISE SIZE QAWPER

226 B a t h t u b s SWIM C series (esign Piero Lissoni ) CORNER bathtub WITH PANELS. CORNER bathtub WITH PANELS. - Technical chart P1 P3 P2 P4 P1 P3 P2 P P1 P3 P2 P4 P1 P3 P2 P Customised. X X 21 Y min 790 / max 1250 X1 min 1750 / max 2050 P1 P2 P3 P X2 Y1 690 Y2 min 50 / max 280 min 50 / max 280 Y1 690 Y2 min 50 / max 280 min 50 / max 280 X2 min 1750 / max 2050 P1 P2 P3 P X1 Y min 790 / max min 50 / max 200 min 50 / max 200 min 50 / max 200 min 50 / max 200 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. The customised bathtub must have on the order the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted

227 B a t h t u b s SWIM C series (esign Piero Lissoni ) CORNER bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 2 sides. The longer side with overflow is always against the wall. CORNER bathtub WITH PANELS. 790 rawn=right () S White QAWANR01 S- 880 rawn=right () S White QAWANR02 S rawn=right (). 500 S White QAWANR03 S rawn=right (). 500 S White QAWANR04 S- Y1 500 X Y Y2 X2 S Feasible sizes: X = min 1750 mm, max 2050 mm / Y = min 790 mm, max 1250 mm. X1 and X2 = min 50 mm, max 200 mm. / Y1 and Y2 = min 50 mm, max 280 mm. In the order please ALWAYS specify the right X, Y, X1, X2, Y1, Y2 dimensions. The X1, X2, Y1 and Y2 sizes can be different from each other, considering always the min. and max. allowed dimensions. With deck-mounted tap, Y1 or Y2 min. mm. rawn=right (). 21 X1 White, CUSTOMISE SIZE QAWANR05 S

228 B a t h t u b s SWIM C series (esign Piero Lissoni ) NICHE bathtub WITH PANELS. NICHE bathtub WITH PANELS. - Technical chart P1 P3 P2 P P1 P3 P2 P X 21 Y min 790 / max 1250 X1 min 1750 / max 2050 P1 P2 P3 P X2 Y1 690 Y2 min 50 / max 280 min 50 / max Customised. 425 min 50 / max 200 min 50 / max 200 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. The customised bathtub must have on the order the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted

229 B a t h t u b s SWIM C series (esign Piero Lissoni ) NICHE bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 1 side. The longer side with overflow is always against the wall. NICHE bathtub WITH PANELS White QAWICR White QAWICR White QAWICR White QAWICR04 X Y1 Y 690 Y2 X2 Feasible sizes: X = min 1750 mm, max 2050 mm / Y = min 790 mm, max 1250 mm. X1 and X2 = min 50 mm, max 200 mm. / Y1 and Y2 = min 50 mm, max 280 mm. In the order please ALWAYS specify the right X, Y, X1, X2, Y1, Y2 dimensions. The X1, X2, Y1 and Y2 sizes can be different from each other, considering always the min. and max. allowed dimensions. With deck-mounted tap, Y1 or Y2 min. mm White, CUSTOMISE SIZE QAWICR05 X

230 B a t h t u b s SWIM C series (esign Piero Lissoni ) Bathtub WITH OPEN-FACE COMPARTMENTS. Bathtub WITH OPEN-FACE COMPARTMENTS. - Technical chart P2 P P2 P P2 P P2 P P4 P3 280 P2 P IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. The NICHE, PENINSULA AN CORNER bathtubs can be installed free-standing too, thanks to the use of panels in white Cristalplant, positioned on sides without open-faced compartments

231 B a t h t u b s SWIM C series (esign Piero Lissoni ) Bathtub WITH OPEN-FACE COMPARTMENTS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on all sides without open-faced compartments. The (S) and () codes indicate the exact position of the removable panel, that allows the inspection of the possible deck-mounted tap. The compartment with the removable panel for inspection is less deep than the adjacent open-face compartments. Ecolak Wood Wood Selection Wood Exclusive Bathtub WITH OPEN-FACE COMPARTMENTS open-faced compartment + 3 fixed panels. In case of bathtub with deck-mounted tap: when tap is positioned on P1 please order bathtub code QAWGNF01, when it s on P2 please order bathtub code QAWGNF01 S. 500 NICHE/FREE-STANING installation, white + finished compartments QAWGNF01 S open-faced compartments + 2 fixed panels. In case of bathtub with deck-mounted tap: when tap is positioned on P1 please order bathtub code QAWGAF01, when it s on P2 please order bathtub code QAWGAF01 S. 500 CORNER/FREE-STANING-LEFT, white + finished compartments QAWGAF01 S open-faced compartments + 2 fixed panels. In case of bathtub with deck-mounted tap: when tap is positioned on P1 please order bathtub code QAWGAF02, when it s on P2 please order bathtub code QAWGAF02 S. 500 CORNER/FREE-STANING-RIGHT, white + finished compartments QAWGAF02 S open-faced compartments + 1 fixed panel. In case of bathtub with deck-mounted tap: when tap is positioned on P1 please order bathtub code QAWGPF01, when it s on P2 please order bathtub code QAWGPF01 S. 500 PENINSULA/FREE-STANING installation, white + finished compartments QAWGPF01 S- 4 open-faced compartments Free-standing installation, white + finished compartments QAWGIF01 S

232 B a t h t u b s ARK (esign Naoto Fukasawa ) Technical features / typologies. Customised bathtub in Cristalplant with double backrest slope. imensions: L = mm / P = mm / H = 460 mm. Versions: BUILT-IN - FREE-STANING WITH PANELS - PENINSULA WITH PANELS - CORNER WITH PANELS - NICHE WITH PANELS. BUILT-IN: upper/under-mounted installation, for walling and panelling supplied by the customer. FREE-STANING WITH PANELS: free-standing installation, with fixed panels in Cristalplant glued on 4 sides. PENINSULA WITH PANELS: peninsula installation, with longer side against the wall and fixed panels in Cristalplant glued on other 3 sides. CORNER WITH PANELS: for corner installation, with fixed panels in Cristalplant glued on 2 sides. NICHE WITH PANELS: for niche installation, with fixed panel in Cristalplant glued on 1 side. Soft Touch: coating made of anthracite grey paint. Certifications: USA - Canada

233 B a t h t u b s ARK (esign Naoto Fukasawa ) Customised BUILT-IN bathtub. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Upper/under-mounted installation, walling and panelling supplied by the customer. Customised BUILT-IN bathtub. - Technical chart. X min 1690 / max 1910 Y2 max 80 P1 P2 Y min 720 / max X1 P P4 X2 Y1 max 110 max 110 max 110 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. On the order please indicate the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted. Customised BUILT-IN bathtub. Y2 720 Y Weight without water: 140 kg - Water capacity: 225 ltr. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Upper/under-mounted installation, walling and panelling supplied by the customer. X Y1 X White QAKSSR01 X

234 B a t h t u b s ARK (esign Naoto Fukasawa ) Customised FREE-STANING bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 4 sides. Customised FREE-STANING bathtub WITH PANELS. - Technical chart. X min 1690 / max 1910 Y2 max 80 P1 P2 Y min 720 / max X1 P P4 X2 Y1 max 110 max 110 max 110 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. On the order please indicate the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted. Customised FREE-STANING bathtub WITH PANELS. X Y2 720 Y Y1 Available versions: totally white / white with panels in Soft touch grey. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 4 sides. Weight without water: 212 kg - Water capacity: 225 ltr. X White QAKISR01 White + Soft Touch grey QAKISS01 X

235 B a t h t u b s ARK (esign Naoto Fukasawa ) Customised PENINSULA bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 3 sides. Customised PENINSULA bathtub WITH PANELS. - Technical chart. X min 1690 / max 1910 Y2 max 80 P1 P2 Y min 720 / max X1 P P4 X2 Y1 max 110 max 110 max 110 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. On the order please indicate the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted. Customised PENINSULA bathtub WITH PANELS. X Y1 720 Y Y2 Available versions: totally white / white with panels in Soft touch grey. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 3 sides. The longer side with overflow is always against the wall.weight without water: 188 kg - Water capacity: 225 ltr. X White QAKPER01 White + Soft Touch grey QAKPES01 X

236 B a t h t u b s ARK (esign Naoto Fukasawa ) Customised CORNER bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 2 sides. Customised CORNER bathtub WITH PANELS. - Technical chart. X min 1690 / max 1910 Y2 max 80 Y2 max 80 X min 1690 / max 1910 P1 P2 P1 P2 Y min 720 / max 910 Y min 720 / max 910 P3 P4 Y1 max 110 Y1 max 110 P3 P4 X X2 X X2 max 110 max 110 max 110 max IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. On the order please indicate the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted. Customised CORNER bathtub WITH PANELS. X Y1 720 Y Y2 Available versions: totally white / white with panels in Soft touch grey. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 2 sides. The longer side with overflow is always against the wall. Weight without water: 176 kg - Water capacity: 225 ltr. rawn=right (), mirrored=left (S). X1 460 X S White QAKANR01 S- White + Soft Touch grey QAKANS01 S

237 B a t h t u b s ARK (esign Naoto Fukasawa ) Customised NICHE bathtub WITH PANELS. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 1 side. Customised NICHE bathtub WITH PANELS. - Technical chart. X min 1690 / max 1910 Y2 Y min 720 / max 910 max 80 P1 P P3 P4 Y1 max 110 X1 max X2 max 110 IMPORTANT : P1, P2, P3 and P4 indicate the possible deck-mounted tap positioning: please add the specific customised solution in the order. The P1 and P2 positions refer to bathtub side with overflow, the P3 and P4 to the opposite side. On the order please indicate the X, Y, X1, X2, Y1 and Y2 dimensions. Orders without dimensions are not accepted. Customised NICHE bathtub WITH PANELS. X Y1 720 Y Y2 Available versions: totally white / white with panels in Soft touch grey. Cristalplant, with adjustment feet, chromium-plated waste drain and siphon. Covering panels on 1 side. The longer side with overflow is always against the wall. Weight without water: 164 kg - Water capacity: 225 ltr. X White QAKICR01 White + Soft Touch grey QAKICS01 X

238 B a t h t u b s Holes for deck-mounted tap set for bathtub. ARK / SWIM C - Hole for deck-mounted tap. Only for taps, listed as compatible. The compatible taps without spout should be integrated with a spout, to be chosen according to the design situation. Water supply from overflow is not possible. Min. bathtub edge: mm. (70 mm. on side with overflow for ARK bathtub). Position P1. - For LIQUI RGSL Position P2. - For LIQUI RGSL Position P3. - For LIQUI RGSL Position P4. - For LIQUI RGSL Position P1. - For LIQUI RESL Position P2. - For LIQUI RESL Position P3. - For LIQUI RESL Position P4. - For LIQUI RESL Position P1. - For CUT RECT10 / RECT Position P2. - For CUT RECT10 / RECT Position P3. - For CUT RECT10 / RECT Position P4. - For CUT RECT10 / RECT Position P1. - For MINIMAL RGM09 or w1 RGFA Position P2. - For MINIMAL RGM09 or w1 RGFA Position P3. - For MINIMAL RGM09 or w1 RGFA Position P4. - For MINIMAL RGM09 or w1 RGFA Position P1. - For MINIMAL RGM10 or w1 RGFA Position P2. - For MINIMAL RGM10 or w1 RGFA Position P3. - For MINIMAL RGM10 or w1 RGFA Position P4. - For MINIMAL RGM10 or w1 RGFA Position P1. - For WINGS RGNS01 / RGNS Position P2. - For WINGS RGNS01 / RGNS Position P3. - For WINGS RGNS01 / RGNS Position P4. - For WINGS RGNS01 / RGNS Position P1. - For WINGS RGNS03 / RGNS Position P2. - For WINGS RGNS03 / RGNS Position P3. - For WINGS RGNS03 / RGNS Position P4. - For WINGS RGNS03 / RGNS Position P1. - For ECLIPSE RGRX Position P2. - For ECLIPSE RGRX Position P3. - For ECLIPSE RGRX Position P4. - For ECLIPSE RGRX Position P1. - For ECLIPSE RGRX Position P2. - For ECLIPSE RGRX Position P3. - For ECLIPSE RGRX Position P4. - For ECLIPSE RGRX Position P1. - For GAREN RGGN05 / PIPE RGFP Position P2. - For GAREN RGGN05 / PIPE RGFP Position P3. - For GAREN RGGN05 / PIPE RGFP Position P4. - For GAREN RGGN05 / PIPE RGFP Position P1. - For GAREN RGGN06 / PIPE RGFP Position P2. - For GAREN RGGN06 / PIPE RGFP Position P3. - For GAREN RGGN06 / PIPE RGFP Position P4. - For GAREN RGGN06 / PIPE RGFP ZVLAC01 ZVLAC02 ZVLAC03 ZVLAC04 ZVLAC05 ZVLAC06 ZVLAC07 ZVLAC08 ZVLAC09 ZVLAC10 ZVLAC11 ZVLAC12 ZVLAC13 ZVLAC14 ZVLAC15 ZVLAC16 ZVLAC17 ZVLAC18 ZVLAC19 ZVLAC20 ZVLAC21 ZVLAC22 ZVLAC23 ZVLAC24 ZVLAC25 ZVLAC26 ZVLAC27 ZVLAC28 ZVLAC29 ZVLAC30 ZVLAC31 ZVLAC32 ZVLAC33 ZVLAC34 ZVLAC35 ZVLAC36 ZVLAC37 ZVLAC38 ZVLAC39 ZVLAC40 ZVLAC41 ZVLAC42 ZVLAC43 ZVLAC

239 S a n i t a r y f i x t u r e s XY (esign Piero Lissoni ) White ceramic, glossy or matt. Suspended bidet with single hole for tap. 275 Ø Weight: 23 kg. Compatible waste drain: ANBN001 chromium-plated / ANHG001 + ANR002 stainless steel Ø Glossy-white QSYBSC01 Matt white QSYBSB01 Suspended toilet bowl Weight: 23 kg. Toilet seat excluded. 180 Ø Ø Glossy-white QSYVSC01 Matt white QSYVSB01 Toilet seat. Thermosetting resin. Hinge with soft-closing mechanism. Glossy-white (resin) AVHA003 Matt white (resin) AVHA004 Brackets. For suspended bidet or toilet bowl AVBF

240 S a n i t a r y f i x t u r e s SAO2 by Galassia White polished ceramic. Floor-mounted bidet with single hole for tap. 330 Ø Weight: 27,5 kg. Compatible waste drain: ANBN001 chromium-plated / ANHG001 + ANR002 stainless steel. Ø C F Glossy-white QSSBTC01 Floor-mounted toilet bowl Floor/wall drainage. Weight: 27,1 kg. Toilet seat excluded Glossy-white QSSVTC01 Suspended bidet with single hole for tap. Ø Weight: 18 kg. Compatible waste drain: ANBN001 chromium-plated / ANHG001 + ANR002 stainless steel Ø C F S Glossy-white QSSBSC01 Suspended toilet bowl Weight: 22,7 kg. Toilet seat excluded Glossy-white QSSVSC

241 S a n i t a r y f i x t u r e s SAO2 by Galassia White polished ceramic. Monobloc toilet bowl Floor/wall drainage. WC weight: 34 kg. Cistern equipped with double-flow drainage mechanism. Toilet seat excluded F Glossy-white. Floor-mounted toilet bowl for cistern QSSVTC02 Glossy-white. Cistern AVHB001 Toilet seat. Thermosetting resin. Hinge with soft-closing mechanism. Glossy-white (resin) AVHA001 Brackets. For suspended bidet or toilet bowl AVBF

242 S a n i t a r y f i x t u r e s XES by Galassia White polished ceramic. Floor-mounted bidet with single hole for tap. 250 Ø Ø C F Weight: 23 kg. Compatible waste drain: ANBN001 chromium-plated / ANHG001 + ANR002 stainless steel. 110 S Glossy-white QSXBTC01 Floor-mounted toilet bowl Floor/wall drainage. Weight: 26 kg. Toilet seat excluded. Ø Glossy-white QSXVTC01 Suspended bidet with single hole for tap. 250 Weight: 17 kg. Compatible waste drain: ANBN001 chromium-plated / ANHG001 + ANR002 stainless steel Ø Ø C S F Glossy-white QSXBSC01 Suspended toilet bowl Weight: 22 kg. Toilet seat excluded Ø Glossy-white QSXVSC

243 S a n i t a r y f i x t u r e s XES by Galassia White polished ceramic. Monobloc toilet bowl Floor/wall drainage. Cistern equipped with double-flow drainage mechanism. Toilet seat excluded F Glossy-white. Floor-mounted toilet bowl for cistern QSXVTC02 Glossy-white. Cistern AVHB003 Toilet seat. Thermosetting resin. Hinge with soft-closing mechanism. Glossy-white (resin) AVHA002 Brackets. For suspended bidet or toilet bowl AVBF

244 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Typologies (esign Monica Armani )

245 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE 18 - Shower trays NEW In matt white Corian. Waste trap included (free-flow), with cover in white Corian. The shower tray can be installed flush with the floor. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE SHOWER OORS. FOR CUSTOMERS SHOWER TRAYS THE CUT-OUT IS BY CUSTOMER. THE CUSTOMISE SOLUTIONS FOR OOR INSTALLATION ARE INCLUE AT NO CHARGE FOR ALL ORERS CONCERNING TAPE 18 SHOWER TRAY + RELATIVE SHOWER BOX. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. FIX-SIZE shower tray Unit price = = A = B = L L = = P P A - rain laterally positioned QTMFP QTMFP QTMFP QTMFP QTMFP QTMFP QTMFP QTMFP QTMFP QTMFP10 B - Center drain QTMGP QTMGP QTMGP QTMGP QTMGP QTMGP QTMGP QTMGP QTMGP QTMGP

246 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE 18 - Shower trays NEW In matt white Corian. Waste trap included (free-flow), with cover in white Corian. The shower tray can be installed flush with the floor. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE SHOWER OORS. FOR CUSTOMERS SHOWER TRAYS THE CUT-OUT IS BY CUSTOMER. THE CUSTOMISE SOLUTIONS FOR OOR INSTALLATION ARE INCLUE AT NO CHARGE FOR ALL ORERS CONCERNING TAPE 18 SHOWER TRAY + RELATIVE SHOWER BOX. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. CUSTOMISE shower tray - L 800 mm / P mm P min. 800 mm, max mm = = 50 A B = 800 = 50 P = A - rain laterally positioned ice per linear metre QTMCP01 B - Center drain ice per linear metre QTMP01 CUSTOMISE shower tray - L 900 mm / P mm P min. 900 mm, max mm = = 50 A B = 900 = 50 P = A - rain laterally positioned ice per linear metre QTMCP02 B - Center drain ice per linear metre QTMP

247 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE SHOWER OORS. FOR CUSTOMERS SHOWER TRAYS THE CUT-OUT IS BY CUSTOMER. THE CUSTOMISE SOLUTIONS FOR OOR INSTALLATION ARE INCLUE AT NO CHARGE FOR ALL ORERS CONCERNING TAPE 18 SHOWER TRAY + RELATIVE SHOWER BOX. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 1 - CORNER shower box WITH OOR - L 800 mm Versions: fixed dimensions / customised P side. Entrance from side L = 800 mm. H = 2 S P + 51 P L = 800 P 625 For TAPE 18 tray: 800 x 800 mm QBT1808F S- 800 x 0 mm QBT1810F S- 800 x 1200 mm QBT1812F S- 800 x 1400 mm QBT1814F S- 800 x 1600 mm QBT1816F S- 625 For customised tray: 800 x min 750 mm, max 0 mm QBT1810V S- 800 x min 1 mm, max 1200 mm QBT1812V S- 800 x min 1201 mm, max 1400 mm QBT1814V S- 800 x min 1401 mm, max 1600 mm QBT1816V S- TYPE 1 - CORNER shower box WITH OOR - L 900 mm Versions: fixed dimensions / customised P side. Entrance from side L = 900 mm H = 2 S P + 51 P L = 900 P 725 For TAPE 18 tray: 900 x min 800 mm, max 999 mm QBT1909F S- 900 x min 1201 mm, max 1400 mm QBT1910F S- 900 x min 1400 mm, max 1600 mm QBT1912F S- 900 x min 1401 mm, max 1600 mm QBT1914F S x min 750 mm, max 0 mm QBT1916F S- 725 For customised tray: 900 x min 750 mm, max 0 mm QBT1910V S- 900 x min 1 mm, max 1200 mm QBT1912V S- 900 x min 1201 mm, max 1400 mm QBT1914V S- 900 x min 1401 mm, max 1600 mm QBT1916V S- 23.6

248 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 2 - CORNER shower box WITHOUT OOR - L 800 mm I - reversibile ENG - reversible F - rèversible - reversibel E - reversible Versions: fixed dimensions / customised P side. Entrance from side L = 800 mm. H = 2 P + 51 P + 51 L = 800 P For TAPE 18 tray: 800 x 1400 mm QBT2814F 800 x 1600 mm QBT2816F For customised tray: 800 x min 1400 mm, max 1600 mm QBT2816V TYPE 2 - CORNER shower box WITHOUT OOR - L 900 mm I - reversibile ENG - reversible F - rèversible - reversibel E - reversible Versions: fixed dimensions / customised P side. Entrance from side L = 900 mm H = 2 P + 51 P + 51 L = 900 P For TAPE 18 tray: 900 x min 1401 mm, max 1600 mm QBT2914F 900 x min 750 mm, max 0 mm QBT2916F For customised tray: 900 x min 1400 mm, max 1600 mm QBT2916V

249 * * S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 3 - CORNER shower box WITHOUT OOR - P 800 mm * I - reversibile ENG - reversible F - rèversible - reversibel E - reversible Fixed dimensions. Entrance from side L = 1600 mm, the other shorter side is fixed P = 800 mm. Entrance side: W. 970 mm glass + entrance W. 630 mm. * = Steel beam necessary ONLY for shower box with side L > 1399 mm. To be ordered separately (see below). H = 2 * L = P = 800 For TAPE 18 tray: 800 x 1600 mm QBT3816F TYPE 3 - CORNER shower box WITHOUT OOR - P 900 mm * I - reversibile ENG - reversible F - rèversible - reversibel E - reversible Fixed dimensions. Entrance from side L = 1600 mm, the other shorter side is fixed P = 900 mm. Entrance side: W. 970 mm glass + entrance W. 630 mm. * = Steel beam necessary ONLY for shower box with side L > 1399 mm. To be ordered separately (see below). H = 2 * L = P = 900 For TAPE 18 tray: 900 x min 750 mm, max 0 mm QBT3916F CUSTOMISE SOLUTIONS AN ACCESSORIES. ZNBC01 = price increase to be added only when the fixed side P is customised. Customised fixed side (P) - Min. 750 mm / max mm ZNBC01 * Extensible steel beam - Min. 750 mm / max mm ZNBC

250 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE SHOWER OORS. FOR CUSTOMERS SHOWER TRAYS THE CUT-OUT IS BY CUSTOMER. THE CUSTOMISE SOLUTIONS FOR OOR INSTALLATION ARE INCLUE AT NO CHARGE FOR ALL ORERS CONCERNING TAPE 18 SHOWER TRAY + RELATIVE SHOWER BOX. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 4 - CORNER shower box WITH OOR - L mm Fixed dimensions. Entrance from side L = mm, the other shorter side is fixed P = 800 / 900 mm. Entrance side: door L1 = 800 mm + variable fixed glass aligned with door. * = Steel beam necessary ONLY for shower box with side L > 1399 mm. To be ordered separately (see below). * L1 * * S H = 2 P + 51 P + 51 L P L1 L1 For TAPE 18 tray: 800 x 0 mm QBT4810F S- 800 x 1200 mm QBT4812F S- 800 x 1400 mm QBT4814F S- 800 x 1600 mm QBT4816F S- L L 900 x min 1201 mm, max 1400 mm QBT4910F S- 900 x min 1400 mm, max 1600 mm QBT4912F S- 900 x min 1401 mm, max 1600 mm QBT4914F S- 900 x min 750 mm, max 0 mm QBT4916F S- CUSTOMISE SOLUTIONS AN ACCESSORIES. ZNBC01 = price increase to be added only when the fixed side P is customised. 23 Customised fixed side (P) - Min. 750 mm / max mm ZNBC01 * Extensible steel beam - Min. 750 mm / max mm ZNBC

251 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE SHOWER OORS. FOR CUSTOMERS SHOWER TRAYS THE CUT-OUT IS BY CUSTOMER. THE CUSTOMISE SOLUTIONS FOR OOR INSTALLATION ARE INCLUE AT NO CHARGE FOR ALL ORERS CONCERNING TAPE 18 SHOWER TRAY + RELATIVE SHOWER BOX. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 4 - CORNER shower box WITH OOR - L mm L : customised side. Entrance from side L = mm, the other shorter side is fixed P = 800 / 900 mm. Entrance side: door L1 = 800 mm + variable fixed glass aligned with door. * = Steel beam necessary ONLY for shower box with side L > 1399 mm. To be ordered separately (see below). * L1 * * S H = 2 P + 51 P + 51 L P L1 L1 For customised tray: 800 x min 0 mm, max 1200 mm QBT4812V S- 800 x min 1201 mm, max 1400 mm QBT4814V S- 800 x min 1401 mm, max 1600 mm QBT4816V S- L L 900 x min 0 mm, max 1200 mm QBT4912V S- 900 x min 1201 mm, max 1400 mm QBT4914V S- 900 x min 1401 mm, max 1600 mm QBT4916V S- 23 CUSTOMISE SOLUTIONS AN ACCESSORIES. ZNBC01 = price increase to be added only when the fixed side P is customised. Customised fixed side (P) - Min. 750 mm / max mm ZNBC01 * Extensible steel beam - Min. 750 mm / max mm ZNBC

252 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE SHOWER OORS. FOR CUSTOMERS SHOWER TRAYS THE CUT-OUT IS BY CUSTOMER. THE CUSTOMISE SOLUTIONS FOR OOR INSTALLATION ARE INCLUE AT NO CHARGE FOR ALL ORERS CONCERNING TAPE 18 SHOWER TRAY + RELATIVE SHOWER BOX. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 4 - CORNER shower box WITH OOR - L mm L : customised side. Entrance from side L = mm, the other shorter side is fixed P = 800 / 900 mm. Entrance side: variable door L1 = mm, without fixed glass aligned with door. S H = 2 P + 51 P + 51 L P For customised tray: 800 x min 800 mm, max 999 mm QBT4809V S- L L 900 x min 800 mm, max 999 mm QBT4909V S- CUSTOMISE SOLUTIONS AN ACCESSORIES. ZNBC01 = price increase to be added only when the fixed side P is customised. 23 Customised fixed side (P) - Min. 750 mm / max mm ZNBC

253 * S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE OORS. FOR CUSTOMERS SHOWER TRAYS THE CUT OUT IS BY CUSTOMER. THE CUSTOMISE SOLUTIONS FOR OOR INSTALLATION, IN THE POSITION INICATE ON TECHNICAL IAGRAM OF TYPE 5 TAPE, ARE INCLUE AT NO CHARGE FOR ALL ORERS CONCERNING TAPE SHOWER TRAY + RELATIVE SHOWER BOX. PLEASE SPECIFY ON THE ORER IF YOU WOUL LIKE TO RECEIVE THE TAPE SHOWER TRAY WITHOUT THE CUT-OUT. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 5 - Shower door for NICHE SOLUTIONS Customised. L min. 750 mm, max. 999 mm. H = 2 S L L L L from 750 to 999 mm QBT5009V S- TYPE 6 - Shower door for NICHE SOLUTIONS, WITH FIXE GLASS ALIGNE WITH OOR Customised. L min. 0 mm, max mm. L 800 mm door + variable fixed glass aligned with door. * = Steel beam necessary ONLY for shower box with side L > 1399 mm. To be ordered separately (see below). * 800 H = 2 S * L L L L L L from 0 to 1200 mm QBT6012V S- L from 1201 to 1400 mm QBT6014V S- L from 1401 to 1600 mm QBT6016V S- CUSTOMISE SOLUTIONS AN ACCESSORIES. 23 * Extensible steel beam - Min. 750 mm / max mm ZNBC

254 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Shower box (esign Monica Armani ) Nominal dimensions: please see the effective dimensions on technical diagram. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam in satin stainless steel. If the shower tray is built into the wall, even only partially, cannot be used with Tape shower box. The above shall not be subject to claims. In these cases please add the customised solution for door installation at customer s charge. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 7 - Shower glass for NICHE SOLUTIONS I - reversibile ENG - reversible F - rèversible - reversibel E - reversible Fixed dimensions. Glass L 0 mm. Fixing beam P 800 / 900 mm. P H = P P For TAPE 18 tray: 800 x 1600 mm QBT7816F S x min 750 mm, max 0 mm QBT7916F S

255 * * S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Customised shower box (esign Monica Armani ) Corner CUSTOMISE compositions, to be used and installed on customer s shower tray or TAPE 18 shower tray built into the wall or positioned under wall covering. Please order separately the door and the fixed side. As an alternative to the door is possible to order the customised fixing beam. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam, hinges and knobs in satin stainless steel. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE OORS, TO BE ARRANGE BY CUSTOMER. For height reductions, if necessary, please add the price increase on door and fixed side, cod. ZNBC06. TAPE - CUSTOMISE shower door L min. 750 mm / L max. 999 mm. On the order please specify the effective L measurement, paying attention to the shower tray parts built into the wall or under wall covering (L = A - SP). L = dimension of the installed shower tray. B - Scarico centrale SP = recessed part of the shower tray. Please order separately the CUSTOMISE fixed side to complete the shower box. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass 2 L L = A - SP SP S SP A L L A L from 750 to 999 mm QBTAV01 S- TAPE - CUSTOMISE shower door, with fixed glass aligned with door * L min. 0 mm / L max mm. On the order please specify the effective L measurement, paying attention to the shower tray parts built into the wall or under wall covering (L = A - SP). L = dimension of the installed shower tray. B - Scarico centrale SP = recessed part of the shower tray. Please order separately the CUSTOMISE fixed side to complete the shower box. * = Steel beam necessary ONLY for shower box with side L > 1399 mm. To be ordered separately (see below). L * S SP L = A - SP SP * A L 23 L from 0 to 1200 mm QBTBV01 S- L from 1201 to 1400 mm QBTBV02 S- L from 1401 to 1600 mm QBTBV03 S- * Extensible steel beam - Min. 750 mm / max mm ZNBC08 L A 23.14

256 A S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Customised shower box (esign Monica Armani ) Corner CUSTOMISE compositions, to be used and installed on customer s shower tray or TAPE 18 shower tray built into the wall or positioned under wall covering. Please order separately the door and the fixed side. As an alternative to the door is possible to order the customised fixing beam. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). Shaped fixing beam, hinges and knobs in satin stainless steel. A SPECIFIC CUT-OUT ON THE SHOWER TRAY IS NECESSARY FOR THE INSTALLATION OF TAPE OORS, TO BE ARRANGE BY CUSTOMER. For height reductions, if necessary, please add the price increase on door and fixed side, cod. ZNBC06. TAPE - CUSTOMISE fixed side 2 I - reversibile ENG - reversible F - rèversible - reversibel E - reversible L min. 750 mm / L max mm. REVERSIBLE: the fixed side can be mounted closed to wall, positioned on right or left side. On the order please specify the effective L measurement, paying attention to the shower tray parts built into the wall or under wall covering (L = A - SP). L = dimension of the installed shower tray. B - Scarico centrale SP = recessed part of the shower tray. Please order separately the CUSTOMISE door to complete the shower box. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass L L = A - SP SP L = A - SP SP SP L A L L A L from 750 to 999 mm QBTCV01 L from 0 to 1200 mm QBTCV02 L from 1201 to 1400 mm QBTCV03 L from 1401 to 1600 mm QBTCV04 TAPE - CUSTOMISE fixing beam L min. 750 mm / L max. 999 mm. On the order please specify the effective L measurement, paying attention to the shower tray parts built into the wall or under wall covering (L = A - SP). L = dimension of the installed shower tray. B - Scarico centrale SP = recessed part of the shower tray. Please order separately the CUSTOMISE fixed side to complete the shower box. 2 L L = A - SP SP SP L A 23 L A AVBX0MC 23.15

257 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Customised solutions (esign Monica Armani ) RRM02 FINO A ESAURIMENTO SCORTE % increase on shower box or door price. < ZNBC06 Height bigger than standard Available ONLY for shower boxes and niche glass panels WITHOUT OOR, TYPE % increase on shower box or niche glass. H max.: 2700 mm. > 2 max ZNBC

258 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 1 - Corner shower box with door L 800 mm. FIXE IMENSIONS. P H 75 H P +11 P L (800) L -14 L L P ( ) P P ,

259 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 1 - Corner shower box with door L 900 mm. FIXE IMENSIONS. P H 75 H P +11 P L (900) L -14 L L P ( ) P P ,

260 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 1 - Corner shower box with door L 800 mm. CUSTOMISE P SIE. P H 75 H P +11 P L (800) L -14 L L P (750* 1600) P -10 P ,

261 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 1 - Corner shower box with door L 900 mm. CUSTOMISE P SIE. P H 75 H P +11 P L (900) L -14 L L P (750* 1600) P -10 P ,

262 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 2 - Corner shower box without door L 800 / 900 mm. FIXE IMENSIONS. P H H P +11 P +51 L ( ) L -14 L L -10 P ( ) P P ,

263 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 2 - Corner shower box without door L 800 / 900 mm. CUSTOMISE P SIE. P H H P +11 P +51 L ( ) L -14 L L -10 P ( ) P -10 P ,

264 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 3 - Corner shower box with glass, without door P 800 / 900 mm. FIXE IMENSIONS P H -20 H 50 L -14 P ( ) P -14 P +11 P P L -10 L (1600) L 3,

265 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 4 - Corner shower box with door L mm. FIXE IMENSIONS P H H L -14 P ( ) P -14 P +11 P P L1 (800) 50 L ( ) L -10 L 625 3,

266 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 4 - Corner shower box with door L mm. CUSTOMISE L SIE P H H L -14 P ( ) P -14 P +11 P P L1 (800) 50 L (0 1600) L -10 L 625 3,

267 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 4 - Corner shower box with door L mm. CUSTOMISE L SIE. 172 P H H L -14 P ( ) P +11 P P L -10 L ( ) L ,

268 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 4 - Corner shower box with door L mm. CUSTOMISE L SIE. 710 P H H L -14 P ( ) P +11 P P L ( ) L L 705 3,

269 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 5 - CUSTOMISE shower door for niche solutions, L mm P H H P P +11 P P L ( ) L

270 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 5 - CUSTOMISE shower door for niche solutions, L mm P H H P P +11 P P L ( ) L

271 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 6 - CUSTOMISE shower door for niche solutions, with fixed glass aligned with door, L mm P H H P P +11 P P L (0 1600) L ,

272 S h o w e r t r a y s a n d s h o w e r b o x e s TAPE - Technical diagram (esign Monica Armani ) TYPE 7 - Shower glass for niche solutions. FIXE IMENSIONS H H P ( ) P -14 P P ,

273 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Typologies (esign Piero Lissoni + C.R.S. Boffi )

274 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Customised shower box (esign Piero Lissoni + C.R.S. Boffi ) Compatible with TAPE 18 or client's shower tray. IMPORTANT!!! - Please specify in the order the dimensions of the installed shower tray (for the boxes type 1/2/3/4) or the distance from a wall to the other (for the shower door type 5). Complaints due to measuring indicated before the shower tray installation will not be accepted. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). ofiles and handle in anodised aluminium, available in black or stainless steel finishes. FIXE HEIGHT 2 mm: customised heights are NOT feasible. Any customised dimensions require the feasibility approval by Boffi. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 1 - CORNER shower box, the door slides towards the glass fixed panel. - L = min 1200 / max 1400 mm. Sliding door + fixed side. P = min 750 / max 0 mm. Entrance width = 540 mm. H = 2 S P L BLACK profiles QBSANE01 S- STAINLESS STEEL profiles QBSANI01 S TYPE 1 - CORNER shower box, the door slides towards the glass fixed panel. - L = min 1401 / max 1800 mm. Sliding door + fixed side. P = min 750 / max 0 mm. Entrance width = 640 mm. H = 2 S L P BLACK profiles QBSANE02 S- STAINLESS STEEL profiles QBSANI02 S

275 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Customised shower box (esign Piero Lissoni + C.R.S. Boffi ) Compatible with TAPE 18 or client's shower tray. IMPORTANT!!! - Please specify in the order the dimensions of the installed shower tray (for the boxes type 1/2/3/4) or the distance from a wall to the other (for the shower door type 5). Complaints due to measuring indicated before the shower tray installation will not be accepted. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). ofiles and handle in anodised aluminium, available in black or stainless steel finishes. FIXE HEIGHT 2 mm: customised heights are NOT feasible. Any customised dimensions require the feasibility approval by Boffi. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 1 - CORNER shower box, the door slides towards the wall. - L = min 1200 / max 1400 mm. Sliding door + fixed side. P = min 750 / max 0 mm. Entrance width = 540 mm. H = 2 S P L BLACK profiles QBSANE03 S- STAINLESS STEEL profiles QBSANI03 S TYPE 1 - CORNER shower box, the door slides towards the wall. - L = min 1401 / max 1800 mm. Sliding door + fixed side. P = min 750 / max 0 mm. Entrance width = 640 mm. H = 2 S L P BLACK profiles QBSANE04 S- STAINLESS STEEL profiles QBSANI04 S

276 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Customised shower box (esign Piero Lissoni + C.R.S. Boffi ) Compatible with TAPE 18 or client's shower tray. IMPORTANT!!! - Please specify in the order the dimensions of the installed shower tray (for the boxes type 1/2/3/4) or the distance from a wall to the other (for the shower door type 5). Complaints due to measuring indicated before the shower tray installation will not be accepted. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). ofiles and handle in anodised aluminium, available in black or stainless steel finishes. FIXE HEIGHT 2 mm: customised heights are NOT feasible. Any customised dimensions require the feasibility approval by Boffi. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 3 - PENINSULA shower box. - L = min 1200 / max 1400 mm. Sliding door + 2 fixed sides. P = min 750 / max 0 mm. Entrance width = 540 mm. H = 2 S P L BLACK profiles QBSPEE01 S- STAINLESS STEEL profiles QBSPEI01 S TYPE 3 - PENINSULA shower box. - L = min 1401 / max 1800 mm. Sliding door + 2 fixed sides. P = min 750 / max 0 mm. Entrance width = 640 mm. H = 2 S L P BLACK profiles QBSPEE02 S- STAINLESS STEEL profiles QBSPEI02 S

277 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Customised shower box (esign Piero Lissoni + C.R.S. Boffi ) Compatible with TAPE 18 or client's shower tray. IMPORTANT!!! - Please specify in the order the dimensions of the installed shower tray (for the boxes type 1/2/3/4) or the distance from a wall to the other (for the shower door type 5). Complaints due to measuring indicated before the shower tray installation will not be accepted. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). ofiles and handle in anodised aluminium, available in black or stainless steel finishes. FIXE HEIGHT 2 mm: customised heights are NOT feasible. Any customised dimensions require the feasibility approval by Boffi. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 4 - Shower door for ASYMMETRICAL PENINSULA solution. - L = min 1200 / max 1400 mm. Please order separately the 2 fixed sides for asymmetric peninsula composition (cod. QBSPLE01 / QBSPLI01). Entrance width = 540 mm.! S H = 2 L BLACK profiles QBSPFE01 S- STAINLESS STEEL profiles QBSPFI01 S- TYPE 4 - Shower door for ASYMMETRICAL PENINSULA solution. - L = min 1401 / max 1800 mm. Please order separately the 2 fixed sides for asymmetric peninsula composition. Entrance width = 640 mm.! S H = 2 L BLACK profiles QBSPFE02 S- STAINLESS STEEL profiles QBSPFI02 S

278 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Customised shower box (esign Piero Lissoni + C.R.S. Boffi ) Compatible with TAPE 18 or client's shower tray. IMPORTANT!!! - Please specify in the order the dimensions of the installed shower tray (for the boxes type 1/2/3/4) or the distance from a wall to the other (for the shower door type 5). Complaints due to measuring indicated before the shower tray installation will not be accepted. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). ofiles and handle in anodised aluminium, available in black or stainless steel finishes. FIXE HEIGHT 2 mm: customised heights are NOT feasible. Any customised dimensions require the feasibility approval by Boffi. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 4 - Fixed side for ASYMMETRICAL PENINSULA solution. - P = min 300 / max 0 mm. Please order the 2 fixed sides (1 and 2) indicating the 2 different depths P1 and P2. Unit price, per each fixed side. Please order separately the door for asymmetric peninsula composition.! 2 1 S S P1 P1 P2 P2 BLACK profiles QBSPLE01 S- STAINLESS STEEL profiles QBSPLI01 S- TYPE 5 - Shower door for NICHE SOLUTIONS. - L = min 1200 / max 1400 mm. Q3 Entrance width = 540 mm. Before placing the order, carefully check the width (L) at three different height (Q1 - Q2 - Q3): if the maximal difference among the dimensions is 5 mm please use the shortest one for your order. If the difference is > 5mm please forward your drawings to Boffi for a feasibility check and approval. Q2 H = 2 Q1 S L BLACK profiles QBSICE01 S- STAINLESS STEEL profiles QBSICI01 S

279 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Customised shower box (esign Piero Lissoni + C.R.S. Boffi ) Compatible with TAPE 18 or client's shower tray. IMPORTANT!!! - Please specify in the order the dimensions of the installed shower tray (for the boxes type 1/2/3/4) or the distance from a wall to the other (for the shower door type 5). Complaints due to measuring indicated before the shower tray installation will not be accepted. 8 mm. thick tempered glass. Crystal clear treatment (anti-drop treatment). ofiles and handle in anodised aluminium, available in black or stainless steel finishes. FIXE HEIGHT 2 mm: customised heights are NOT feasible. Any customised dimensions require the feasibility approval by Boffi. Transparent glass Extralight transparent glass Transparent smoky grey glass Frosted Extralight glass Frosted ribbed Extralight glass / Strip matè Extralight glass TYPE 5 - Shower door for NICHE SOLUTIONS. - L = min 1401 / max 1800 mm. Q3 Entrance width = 640 mm. Before placing the order, carefully check the width (L) at three different height (Q1 - Q2 - Q3): if the maximal difference among the dimensions is 5 mm please use the shortest one for your order. If the difference is > 5mm please forward your drawings to Boffi for a feasibility check and approval. Q2 H = 2 Q1 S L BLACK profiles QBSICE02 S- STAINLESS STEEL profiles QBSICI02 S

280 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Technical chart (esign Piero Lissoni + C.R.S. Boffi ) TYPE 1 - CORNER shower box, the door slides towards the glass fixed panel. Customised. L - 6 P - 5,5 2 5, P P - 5, ,5 6 L L ,5 5,

281 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Technical chart (esign Piero Lissoni + C.R.S. Boffi ) TYPE 1 - CORNER shower box, the door slides towards the wall. Customised. L - 6 P -5,5 2 5, P P -5, ,5 6 L L ,5 23 5,

282 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Technical chart (esign Piero Lissoni + C.R.S. Boffi ) TYPE 3 - PENINSULA shower box. Customised. rawn=right (), mirrored=left (S). L -12 P -5,5 2 5, ,5 P P -5, , L L , ,

283 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Technical chart (esign Piero Lissoni + C.R.S. Boffi ) TYPE 4 - ASYMMETRICAL PENINSULA shower box. Customised. rawn=right (), mirrored=left (S). L - 12 P2-5,5 2 5, ,5 P P - 5,5 P2 P2-5,5 5, L L 5, , ,

284 S h o w e r t r a y s a n d s h o w e r b o x e s SLIING - Technical chart (esign Piero Lissoni + C.R.S. Boffi ) TYPE 5 - Shower door for NICHE SOLUTIONS. Customised. L Q3 = 2 Q2 = Q1 300 L , ,5 23 IMPORTANT! : Before placing the order, carefully check the width (L) at three different height (Q1 - Q2 - Q3): if the maximal difference among the dimensions is 5 mm please use the shortest one for your order. If the difference is > 5mm please forward your drawings to Boffi for a feasibility check and approval

285 T a p s ECLIPSE (esign Studiocharlie ) Taps in AISI 304 stainless steel - Finish: satin or grey PV. The round upper surface of mixers, taps and diverters is made of polished stainless steel, both for taps in satin stainless steel and grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Short mixer tap for washbasin. Tall mixer tap for washbasin Ø Ø Ø Ø50 Cartridge for single lever mixers. Flow rate: 4,5 l/min. Cartridge for single lever mixers. Flow rate: 4,5 l/min. Satin stainless steel..... Grey PV..... RERX01 RERX11 Satin stainless steel..... Grey PV..... RERX02 RERX12 Freestanding floor-mounted mixer tap for washbasin. Mixer tap for bidet Ø18 Ø Ø50 12 Ø Cartridge for single lever mixers. Flow rate: 4,5 l/min. Cartridge for single lever mixers. Flow rate: 4,5 l/min. Satin stainless steel..... Grey PV..... RERX03 RERX13 Satin stainless steel..... Grey PV..... RERX04 RERX14 Top-mounted mixer tap for washbasin. Wall-mounted, built-in washbasin mixer tap. Ø80 Ø60 Ø60 Compatible with all top- or wall-mounted spouts. Cartridge for single lever mixers. Cartridge for single lever mixers. Please order the spout (compulsory) separately. Compatible with all wall-mounted spouts. The spout must be ALWAYS installed on the left side of the mixer, as shown in the drawing. Satin stainless steel..... Grey PV..... RERX05 RERX15 Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RERX06E RERX16E RERX06I

286 T a p s ECLIPSE (esign Studiocharlie ) Taps in AISI 304 stainless steel - Finish: satin or grey PV. The round upper surface of mixers, taps and diverters is made of polished stainless steel, both for taps in satin stainless steel and grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Top-mounted tap pair for washbasin. Wall-mounted, built-in tap pair for washbasin. Ø Ø60 Ø80 Ø60 Ø60 Compatible with all top- or wall-mounted spouts. 1/2 ceramic screw disks, 90 opening. Please order the spout (compulsory) separately. Compatible with all wall-mounted spouts. The spout must be ALWAYS installed as shown in the drawing. 1/2 ceramic screw disks, 90 opening. Satin stainless steel..... Grey PV..... RGRX01 RGRX06 Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RGRX02E RGRX07E RGRX02I Wall-mounted, built-in washbasin/shower mixer tap. Wall-mounted spout for washbasin. Ø80 Ø Ø60 Ø21 50 Cartridge for single lever mixers. Compatible with all top- or wall-mounted spouts. Compatible with all wall-mounted shower heads or hand-showers. The customer can choose to install the mixer with or without the supplied washer Ø 80 mm. 1/2 connection. Flow rate: 4,5 l/min. Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RERX10E RERX20E RERX10I Satin stainless steel, P 160 mm..... Grey PV, P 160 mm..... Satin stainless steel, P 230 mm..... Grey PV, P 230 mm..... RIRX01 RIRX07 RIRX02 RIRX08 Top-mounted spout for washbasin. Top-mounted spout for washbasin Ø Ø21 Ø Ø60 3/8 connection. Flow rate: 4,5 l/min. 3/8 connection. Flow rate: 4,5 l/min. 24 Satin stainless steel, H 170 mm.... Grey PV, H 170 mm.... RIRX03 RIRX09 Satin stainless steel, H 280 mm.... Grey PV, H 280 mm.... RIRX04 RIRX

287 T a p s ECLIPSE (esign Studiocharlie ) Taps in AISI 304 stainless steel - Finish: satin or grey PV. The round upper surface of mixers, taps and diverters is made of polished stainless steel, both for taps in satin stainless steel and grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Freestanding floor-mounted spout for washbasin. Freestanding floor-mounted spout for bathtub Ø21 Ø21 Ø90 Ø90 Flow rate: 4,5 l/min. The grey PV version is made in 2 pieces. Flow rate: 24,0 l/min. Satin stainless steel, H 1057 mm.... Grey PV, H 1057 mm.... RIRX05 RIRX11 Satin stainless steel, H 752 mm.... Grey PV, H 752 mm.... RIRX06 RIRX12 Wall-mounted, built-in tap set for shower/bathtub. Wall-mounted, built-in tap set for shower/bathtub. Ø80 Ø80 Ø80 Ø60 Ø80 Ø60 Ø60 Ø60 Single lever mixer tap with cartridge, 2-way diverter and hand-shower. Bathtub use: water supply to overflow. The customer can choose to install the single elements with or without the supplied washer Ø 80 mm. Single lever mixer tap with cartridge, 3-way diverter and hand-shower. The customer can choose to install the single elements with or without the supplied washer Ø 80 mm. Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RERX07E RERX17E RERX07I Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RERX08E RERX18E RERX08I Wall-mounted, built-in thermostatic tap set for shower. Wall-mounted, built-in thermostatic tap set for shower. Ø80 Ø80 Ø80 Ø60 Ø80 Ø60 Ø60 Ø60 Thermostatic mixer, 2-way diverter, hand-shower. The customer can choose to install the single elements with or without the supplied washer Ø 80 mm. Thermostatic mixer, 3-way diverter, hand-shower. The customer can choose to install the single elements with or without the supplied washer Ø 80 mm. Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RHRX01E RHRX05E RHRX01I Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RHRX02E RHRX06E RHRX02I

288 T a p s ECLIPSE (esign Studiocharlie ) Taps in AISI 304 stainless steel - Finish: satin or grey PV. The round upper surface of mixers, taps and diverters is made of polished stainless steel, both for taps in satin stainless steel and grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Built-in deck-mounted tap set for bathtub. Built-in deck-mounted tap set for bathtub. Without spout. Ø Ø Ø60 Ø60 Ø60 Ø60 Ø42 Ø60 Ø42 Cold/warm taps, spout, hand-shower with its mixer. 1/2 ceramic screw disks, 90 opening. Cold/warm taps, hand-shower with its mixer. 1/2 ceramic screw disks, 90 opening. Satin stainless steel..... Grey PV..... RGRX03 RGRX08 Satin stainless steel..... Grey PV..... RGRX04 RGRX09 Wall-mounted, built-in tap set for bathtub. Freestanding floor-mounted bathtub tap set Ø120 Single lever mixer tap with cartridge, spout, diverter and hand-shower. The customer can choose to install the single elements (spout excluded) with or without the supplied washer Ø 80 mm. Single lever mixer tap with cartridge, spout, hand-shower with its mixer. Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RGRX05E RGRX10E RGRX05I Satin stainless steel..... Grey PV..... RERX09 RERX19 Thermostatic mixer. Wall-mounted hand shower. Ø Ø60 Ø60 Compatible with all wall-mounted shower heads or hand-showers. With 1500 mm long hose and water connection. 24 Satin stainless steel, external part..... Grey PV, external part..... Recessed part..... RHRX03E RHRX07E RHRX03I Satin stainless steel..... Grey PV..... RJRX01 RJRX

289 T a p s ECLIPSE (esign Studiocharlie ) Taps in AISI 304 stainless steel - Finish: satin or grey PV. The round upper surface of mixers, taps and diverters is made of polished stainless steel, both for taps in satin stainless steel and grey PV finish. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Wall-mounted shower head. 72 Ø 250 With adjustable mechanism. iameter: 250 mm. Satin stainless steel..... Grey PV..... RRRX01 RRRX

290 T a p s GAREN (esign Piero Lissoni ) Taps in AISI 304 stainless steel - Finish: grey PV. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Top-mounted mixer tap for washbasin. Wall-mounted, built-in washbasin mixer tap Ø 60 * Ø 60 Compatible with all top- or wall-mounted spouts. ogressive ceramic cartridge, 90 opening. Please order the spout (compulsory) separately. Compatible with all wall-mounted spouts. The spout must be ALWAYS installed on the left side of the mixer, as shown in the drawing. * = the Ø 80 mm washer is included. ogressive ceramic cartridge, 90 opening. Grey PV..... REGN01 Grey PV, external part..... Recessed part..... REGN02E REGN02I Freestanding floor-mounted mixer tap for washbasin. Top-mounted tap pair for washbasin Ø 60 ogressive ceramic cartridge, 90 opening. Flow rate: 4,5 l/min. Compatible with all top- or wall-mounted spouts. 1/2 ceramic screw disks, 90 opening. Grey PV..... REGN03 Grey PV..... RGGN01 Wall-mounted, built-in tap pair for washbasin. * 60 Wall-mounted, built-in mixer tap for washbasin / bidet / shower. Ø * Ø * 148 Please order the spout (compulsory) separately. Compatible with all wall-mounted spouts. The spout must be ALWAYS installed as shown in the drawing. * = the Ø 80 mm washer is included. 1/2 ceramic screw disks, 90 opening. Compatible with all top- or wall-mounted spouts. Compatible with all wall-mounted shower heads and hand-showers. * = the Ø 80 mm washer is included. ogressive ceramic cartridge, 90 opening. 24 Grey PV, external part..... Recessed part..... RGGN02E RGGN02I Grey PV, external part..... Recessed part..... REGN04E REGN04I 24.8

291 T a p s GAREN (esign Piero Lissoni ) Taps in AISI 304 stainless steel - Finish: grey PV. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Wall-mounted, built-in thermostatic mixer tap Ø80 Ø60 Wall-mounted, built-in tap set for shower/bathtub. * * * Ø Ø Mixer tap with 90 progressive cartridge, 2-way diverter and hand-shower. Bathtub use: water supply to overflow. * = the Ø 80 mm washer is included. Grey PV, external part..... Recessed part..... REGN06E RHRX03I Grey PV, external part..... Recessed part..... RGGN03E RGGN03I Wall-mounted, built-in tap set for shower. * * * 60 Ø Ø 60 Wall-mounted, built-in thermostatic tap set for shower. * * Ø Ø 60 Ø Mixer tap with 90 progressive cartridge, 3-way diverter and hand-shower. * = the Ø 80 mm washer is included. Thermostatic mixer, 2-way diverter, hand-shower. * = the Ø 80 mm washer is included. Grey PV, external part..... Recessed part..... RGGN04E RGGN04I Grey PV, external part..... Recessed part..... RHGN02E RHGN02I Wall-mounted, built-in thermostatic tap set for shower. * * Ø Ø 60 Ø 60 Wall-mounted, built-in tap set for bathtub. * * * * 60 Ø Ø Thermostatic mixer, 3-way diverter, hand-shower. * = the Ø 80 mm washer is included. Mixer tap with 90 progressive cartridge, spout, diverter and hand-shower. * = the Ø 80 mm washer is included. Grey PV, external part..... Recessed part..... RHGN03E RHGN03I Grey PV, external part..... Recessed part..... RGGN07E RGGN07I

292 T a p s GAREN (esign Piero Lissoni ) Taps in AISI 304 stainless steel - Finish: grey PV. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Built-in deck-mounted tap set for bathtub. Built-in deck-mounted tap set for bathtub. Without spout Ø Ø 60 Cold/warm taps, spout, hand-shower with its mixer. 1/2 ceramic screw disks, 90 opening. Cold/warm taps, hand-shower with its mixer. 1/2 ceramic screw disks, 90 opening. Grey PV..... RGGN05 Grey PV..... RGGN06 Freestanding floor-mounted bathtub tap set. 220 Wall-mounted spout for washbasin/bidet. Ø Ø * Cold/warm taps, spout, diverter, hand-shower. 1/2 ceramic screw disks, 90 opening. * = the Ø 80 mm washer is included. Flow rate: 4,5 l/min. Grey PV..... RGGN08 Grey PV, P 128 mm..... RIGN01 Wall-mounted spout for washbasin. Ø 60 Top-mounted spout for washbasin. 118 * Ø * = the Ø 80 mm washer is included. Flow rate: 4,5 l/min. Flow rate: 4,5 l/min. 24 Grey PV, P 230 mm..... RIGN02 Grey PV, H 133 mm.... RIGN

293 T a p s GAREN (esign Piero Lissoni ) Taps in AISI 304 stainless steel - Finish: grey PV. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. Top-mounted spout for washbasin. Wall-mounted hand shower Ø * Ø 60 Flow rate: 4,5 l/min. With 1500 mm long hose and water connection. * = the Ø 80 mm washer is included. Grey PV, H 264 mm.... RIGN04 Grey PV..... RJGN01 Shower head. Shower arm Anti-limestone membrane in silicone. Compatible with RRGN02 - RRGN03. Flow rate: RFGN01 18,0 l/min - RFGN02 24,0 l/min. 1/2 connection. With swivel ball. Grey PV, ø Grey PV, ø RFGN01 RFGN02 Grey PV..... RRGN02 Ceiling connection for shower head. Wall-mounted toilet shower. Ø Ø Ø Ø 22 1/2 connection. With swivel ball. 1/2 connection. With 1200 mm long hose and water connection. The nozzle for converting into hand shower is included. Grey PV..... RRGN03 Grey PV..... RRGN

294 T a p s PIPE (esign Marcel Wanders ) Taps in AISI 304 stainless steel - Finish: satin with red handle. Top-mounted mixer tap for washbasin. Top-mounted tap pair for washbasin. 36 Ø 70 Ø Compatible with all top- or wall-mounted spouts. ogressive ceramic cartridge, 90 opening. Compatible with all top- or wall-mounted spouts. 1/2 ceramic screw disks, 90 opening. Satin stainless steel + red.... REFP03 Satin stainless steel + red.... RGFP01 Wall-mounted, built-in mixer tap for washbasin / bidet / shower. * 39 Wall-mounted mixer tap for washbasin / shower. Ø90 70 Ø 70 Ø83 Compatible with all top- or wall-mounted spouts. Compatible with all wall-mounted shower heads or hand-showers. * = the Ø 80 mm washer is included. ogressive ceramic cartridge, 90 opening. 1/2 connection. Compatible with all top- or wall-mounted spouts. Cartridge for single lever mixers. Flow rate: 16,0 l/min. Satin stainless steel + red. External part..... Recessed part..... REFP04E REGN04I Satin stainless steel + red.... REFP02 Wall-mounted, built-in washbasin mixer tap. * 39 Wall-mounted, built-in tap pair for washbasin. * 39 Ø 70 * Ø 70 Please order the spout (compulsory) separately. Compatible with all wall-mounted spouts. The spout must be ALWAYS installed on the left side of the mixer, as shown in the drawing. * = the Ø 80 mm washer is included. ogressive ceramic cartridge, 90 opening. Please order the spout (compulsory) separately. Compatible with all wall-mounted spouts. The spout must be ALWAYS installed as shown in the drawing. * = the Ø 80 mm washer is included.1/2 ceramic screw disks, 90 opening. Satin stainless steel + red. External part Recessed part..... REFP06E REGN02I Satin stainless steel + red. External part..... Recessed part..... RGFP02E RGGN02I 24.12

295 T a p s PIPE (esign Marcel Wanders ) Taps in AISI 304 stainless steel - Finish: satin with red handle. Top-mounted mixer tap for washbasin. Ø70 Freestanding floor-mounted mixer tap for washbasin Ø50 0 3/8 connection. Compatible with all top- or wall-mounted spouts. With hose. Flow rate: 10,0 l/min. Cartridge for single lever mixers. ogressive ceramic cartridge, 90 opening. Flow rate: 4,5 l/min. Satin stainless steel + red.... REFP01 Satin stainless steel + red.... REFP05 Top-mounted spout for washbasin/bathtub. Spout for bidet Ø Ø Flow rate: washbasin use 4,5 l/min - bathtub use 26,0 l/min. Lockable swivel aerator. Flow rate: 8,6 l/min. Satin stainless steel, H 220 mm.... Satin stainless steel, H 290 mm..... RIFP01 RIFP02 Satin stainless steel..... RIFP07 Wall-mounted spout for washbasin/bathtub. Freestanding floor-mounted spout * Ø 25 Ø Flow rate: washbasin use 4,5 l/min - bathtub use 26,0 l/min. * = supplied Ø 80 mm washer. Flow rate: RIFP05 4,5 l/min - RIFP06 26,0 l/min. Satin stainless steel, P 150 mm..... Satin stainless steel, P 220 mm..... RIFP03 RIFP04 Satin stainless steel, for washbasin - H 1070 mm... Satin stainless steel, for bathtub - H 770 mm RIFP05 RIFP

296 T a p s PIPE (esign Marcel Wanders ) Taps in AISI 304 stainless steel - Finish: satin with red handle. Wall-mounted, built-in thermostatic mixer tap Ø80 Ø60 Wall-mounted, built-in tap set for shower/bathtub. * * * 39 Ø Mixer tap with 90 progressive cartridge, 2-way diverter and hand-shower. Bathtub use: water supply to overflow. * = the Ø 80 mm washer is included. Satin stainless steel, external part..... Recessed part..... REFP07E RHRX03I Satin stainless steel + red. External part..... Recessed part..... RGFP03E RGGN03I Wall-mounted, built-in tap set for shower. * * * 39 Ø 70 Wall-mounted, built-in thermostatic tap set for shower Ø 80 * * Ø Single lever mixer tap with 90 progressive cartridge, 3-way diverter and handshower. * = the Ø 80 mm washer is included. Thermostatic mixer, 2-way diverter, hand-shower. * = the Ø 80 mm washer is included. Satin stainless steel + red. External part..... Recessed part..... RGFP04E RGGN04I Satin stainless steel + red. External part..... Recessed part..... RHFP02E RHGN02I Wall-mounted, built-in thermostatic tap set for shower. Freestanding floor-mounted bathtub tap set. * * Ø Ø Ø Thermostatic mixer, 3-way diverter, hand-shower. * = the Ø 80 mm washer is included. Cold/warm taps, spout, diverter, hand-shower. 1/2 ceramic screw disks, 90 opening. 24 Satin stainless steel + red. External part..... Recessed part..... RHFP03E RHGN03I Satin stainless steel + red.... RGFP

297 T a p s PIPE (esign Marcel Wanders ) Taps in AISI 304 stainless steel - Finish: satin with red handle. Built-in deck-mounted tap set for bathtub. Built-in deck-mounted tap set for bathtub. Without spout Ø Ø 70 Cold/warm taps, spout, hand-shower with its mixer. 1/2 ceramic screw disks, 90 opening. Cold/warm taps, hand-shower with its mixer. 1/2 ceramic screw disks, 90 opening. Satin stainless steel + red.... RGFP06 Satin stainless steel + red.... RGFP07 Wall-mounted, built-in tap set for bathtub. * * * * 39 Ø 70 Wall-mounted spout for shower. 400 Ø Mixer tap with 90 progressive cartridge, spout, diverter and hand-shower. * = the Ø 80 mm washer is included. 1/2 connection. ovided with supporting part. Flow rate: 16,0 l/min. Satin stainless steel + red. External part..... Recessed part..... RGFP08E RGGN07I Satin stainless steel..... RFFP01 Freestanding floor-mounted spout for shower. Freestanding floor-mounted spout with mixer for shower Ø90 Ø /2 connection. ovided with fixing flange and drain well. Flow rate: 16,0 l/min. 1/2 connections. ogressive ceramic cartridge, 90 opening. ovided with fixing flange and drain well. Flow rate: 14,0 l/min. Satin stainless steel..... RFFP02 Satin stainless steel + red.... RFFP

298 T a p s PIPE (esign Marcel Wanders ) Taps in AISI 304 stainless steel - Finish: satin with red handle. Wall-mounted hand shower. 90 Ø * With 1500 mm long hose and water connection. * = the Ø 80 mm washer is included. Satin stainless steel..... RJFP

299 T a p s UNI (esign C.R.S. Boffi) Taps in AISI 304 stainless steel - Finish: satin. Mixer tap for washbasin. 120 Mixer tap for bidet Ø50 65 Ø50 55 Flow rate: 5,7 l/min. Flow rate: 5,7 l/min. Satin stainless steel..... REFU01 Satin stainless steel..... REFU02 Tall mixer tap for washbasin. Free standing floor-mounted mixer tap for washbasin Ø50 Ø Flow rate: 5,7 l/min. Flow rate: 5,7 l/min. Satin stainless steel..... REFU03 Satin stainless steel..... REFU

300 T a p s UNI (esign C.R.S. Boffi) Taps in AISI 304 stainless steel - Finish: satin. Ceiling-fixed shower head. Wall-mounted shower head RFGZ03: rain option with max flow rate of 20 l/min. RFGZ02: rain option with max flow rate of 20 l/min. Aerator for massage with free flow rate. It requires 2 dedicated ways. RFGZ01: rain option with max flow rate of 20 l/min. Waterfall massage option with free flow rate. It requires 2 dedicated ways. The drawing and the picture are referred to the shower head cod. RFGZ01. RFGZ04: rain option with max flow rate of 14 l/min. Satin stainless steel, rain option.... RFGZ03 Satin stainless steel, rain + aerator for massage options.. RFGZ02 Satin stainless steel, rain + waterfall options.... RFGZ01 Satin stainless steel, recessed part..... Satin stainless steel, rain option, external part.... RRGZ01 RFGZ04 Wall-mounted shower head RFGZ05: waterfall option with free flow rate, min 14l/min. Satin stainless steel, recessed part..... Satin stainless steel, waterfall option, external part. RRGZ01 RFGZ

301 T a p s MINIMAL (esign Giulio Gianturco ) Taps in AISI 304 stainless steel - Finish: satin. Mixer tap for washbasin and bidet. Wall-mounted, built-in tap pair Ø Ø /190/270 Flow rate: 8,4 l/min. Please order the spout or the shower head separately. Compatible with all top- or wall-mounted spouts. Compatible with all wall-mounted shower heads or hand-showers. Ceramic screw disks, 90 opening. Flow rate: 16,0 l/min. REM07: UNTIL STOCK LASTS Satin stainless steel, spout H 125 mm.... Satin stainless steel, spout H 275 mm..... Satin stainless steel, spout H 355 mm..... REM02 REM01 REM07 Recessed part..... Satin stainless steel, external part..... RGM08I RGM08E Top-mounted mixer tap for washbasin. Wall-mounted mixer tap for washbasin / shower. Ø ,5 Compatible with all top- or wall-mounted spouts. 3/8 connection. With hoses. Flow rate: 12,0 l/min. Flow rate: 16,0 l/min. Satin stainless steel..... REM08 Satin stainless steel..... REM03 Top-mounted spout for washbasin. Wall-mounted water connection Ø 55 15/165/260 Ø With 500 mm long hose, ø 3/8-1/2. Flow rate: 8,4 l/min. 1/2 connection. Compatible with RIM RIM04 / RIM10: UNTIL STOCK LASTS Satin stainless steel, H 110 mm.... Satin stainless steel, H 260 mm..... Satin stainless steel, H 355 mm..... RIM04 RIM03 RIM10 Satin stainless steel..... RRM

302 T a p s MINIMAL (esign Giulio Gianturco ) Taps in AISI 304 stainless steel - Finish: satin. Wall-mounted spout for washbasin. Top-mounted tap for washbasin. 210/250 Ø 60 Ø /2 connection. Flow rate: 8,4 l/min. Either cold or warm water supply. With 500 mm long hose. 1/2 connection. Control with milled metal ring on the spout. Flow rate: 8,4 l/min. RIM07: UNTIL STOCK LASTS AVAILABLE UNTIL STOCK LASTS Satin stainless steel, P 210 mm..... Satin stainless steel, P 250 mm..... RIM07 RIM06 Satin stainless steel..... RGM07 Wall-mounted, built-in thermostatic bath/shower mixer tap. 130 Wall-mounted, built-in bath/shower mixer tap Ø Ø 60 Optional diverter. Flow rate: 24,0 l/min. Optional diverter. Flow rate: 24,0 l/min. Recessed part..... Satin stainless steel, external part..... Satin stainless steel, diverter kit..... RHM01I RHM01E RVM01 Recessed part..... Satin stainless steel, external part..... Satin stainless steel, diverter kit..... RHM02I RHM02E RVM01 Wall-mounted spout for bathtub. eck-mounted spout for bathtub Ø 25 Ø Ø /2 connection. Flow rate: 26,0 l/min. 1/2 connection. Flow rate: 26,0 l/min. AVAILABLE UNTIL STOCK LASTS AVAILABLE UNTIL STOCK LASTS 24 Satin stainless steel, P 200 mm..... Satin stainless steel, P 300 mm..... RIM02 RIM01 Satin stainless steel..... RIM

303 T a p s MINIMAL (esign Giulio Gianturco ) Taps in AISI 304 stainless steel - Finish: satin. Freestanding floor-mounted spout for washbasin. Freestanding floor-mounted spout for bathtub Ø 80 Ø 80 1/2 connection. Flow rate: 8,4 l/min. 1/2 connection. Compatible with RHM01-02 and REM03. Flow rate: 26,0 l/min. Satin stainless steel..... RIM09 Satin stainless steel..... RIM05 Shower head. Wall connection for shower head Ø Anti-limestone membrane in silicone. RFM02: compatible with RRM RFM03: compatible with RRM Flow rate: RFM02 18,0 l/min - RFM03 24,0 l/min. With extension and water connection. 1/2 connection. With swivel ball. Satin stainless steel, ø Satin stainless steel, ø RFM02 RFM03 Satin stainless steel..... RRM01 Shower arm. Ceiling connection for shower head. Ø Ø 55 mm. RRM02 RRM Ø Ø Ø /2 connection. With swivel ball. 1/2 connection. RRM02: with extension and water connection. RRM11: ceiling connection. With swivel ball. RRM02: UNTIL STOCK LASTS Satin stainless steel..... RRM08 Satin stainless steel, with hose.... Satin stainless steel..... RRM02 RRM

304 T a p s MINIMAL (esign Giulio Gianturco ) Taps in AISI 304 stainless steel - Finish: satin. Free standing floor-mounted shower spout. Wall-mounted hand shower Ø Ø 120 1/2 connection. Flow rate: 16 l/min. 1/2 connection. Anti-limestone membrane in silicone. With 1500 mm long hose and water connection. Flow rate: 14,0 l/min. Satin stainless steel..... RFM01 Satin stainless steel..... RJM01 eck-mounted hand shower. Wall-mounted toilet shower Ø Ø /2 connection. Anti-limestone membrane in silicone mm long hose. Flow rate: 14,0 l/min. 1/2 connection. With 1200 mm long hose and water connection. The nozzle for converting into hand shower is included. AVAILABLE UNTIL STOCK LASTS Satin stainless steel..... RJM02 Satin stainless steel..... Polished stainless steel..... RRM10 RRM09 Wall-mounted, built-in 5-way diverter. Built-in deck-mounted tap set for bathtub Ø 25 Ø /2 connections. Cold/warm taps with 3/4 screw disks. Spout. Hand shower with dedicated mixer. Flow rate: 22,0 l/min. 24 Recessed part..... Satin stainless steel, external part..... RVM02I RVM02E Satin stainless steel..... RGM

305 T a p s MINIMAL (esign Giulio Gianturco ) Taps in AISI 304 stainless steel - Finish: satin. Built-in deck-mounted tap set for bathtub. Without spout. Freestanding floor-mounted bathtub tap set. Ø Ø Ø120 Cold/warm taps with 3/4 screw disks. Hand shower with dedicated mixer. Flow rate: 22,0 l/min. Consisting of: mixer, spout, hand shower and diverter. 1/2 connections. Flow rate: 18,0 l/min. Satin stainless steel..... RGM10 Satin stainless steel..... REM09 shut-off valve Ceramic screw disk. 1/2 connection. Flow rate: 26,0 l/min. Recessed part..... Satin stainless steel, external part..... RGM05I RGM05E

306 T a p s WINGS (esign Mario Tessarollo ) Taps in AISI 304 stainless steel - Finish: satin or polished. Wall-mounted, built-in tap set for washbasin / bidet. Spout for washbasin, for wall-mounted tap set Ø Spout to be ordered separately. Compatible ONLY with RINS Please add the recessed wall container for tap. In case of use on Pianura back-splash, please add the plate cod. RRNS04 (the recessed container is not necessary). POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Flow rate: 8,4 l/min. Compatible ONLY with RHNS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Satin stainless steel..... Polished stainless steel..... RHNS01 RHNS02 Satin stainless steel, P 150 mm..... Polished stainless steel, P 150 mm..... Satin stainless steel, P 220 mm..... Polished stainless steel, P 220 mm..... RINS01 RINS02 RINS03 RINS04 Spout for bidet, for wall-mounted tap set. Wall-mounted, built-in tap set for washbasin / bidet / shower Ø Flow rate: 8,4 l/min. Compatible ONLY with RHNS Compatible with all top- or wall-mounted spouts, except for RINS Please add the recessed wall container for tap. POLISHE STAINLESS STEEL: UNTIL STOCK LASTS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Satin stainless steel, P 150 mm..... Polished stainless steel, P 150 mm..... Satin stainless steel, P 220 mm..... Polished stainless steel, P 220 mm..... RINS05 RINS06 RINS07 RINS08 Satin stainless steel..... Polished stainless steel..... RHNS03 RHNS04 Top-mounted tap set for washbasin. Top-mounted spout for washbasin Ø Compatible with all top- or wall-mounted spouts, except for RINS rainage box included. Flow rate: 12,0 l/min. Without spout. Flow rate: 8,4 l/min. POLISHE STAINLESS STEEL: UNTIL STOCK LASTS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS 24 Satin stainless steel..... Polished stainless steel..... RHNS05 RHNS06 Satin stainless steel, H 150 mm.... Polished stainless steel, H 150 mm..... Satin stainless steel, H 220 mm..... Polished stainless steel, H 220 mm..... RINS09 RINS10 RINS11 RINS

307 T a p s WINGS (esign Mario Tessarollo ) Taps in AISI 304 stainless steel - Finish: satin or polished. Spout for bidet. Freestanding floor-mounted spout for washbasin Ø Ø Ø 90 Flow rate: 8,4 l/min. Flow rate: RINS ,4 l/min - RINS l/min. POLISHE STAINLESS STEEL: UNTIL STOCK LASTS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Satin stainless steel..... Polished stainless steel..... RINS13 RINS14 Satin stainless steel..... Polished stainless steel..... RINS15 RINS16 Freestanding floor-mounted spout for bathtub. Wall-mounted, built-in tap set for bathtub Ø Ø 90 Spout to be ordered separately. Compatible ONLY with RINS Please add the recessed wall container for tap. Flow rate: 24,0 l/min. POLISHE STAINLESS STEEL: UNTIL STOCK LASTS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Satin stainless steel..... Polished stainless steel..... RINS17 RINS18 Satin stainless steel..... Polished stainless steel..... RHNS07 RHNS08 Wall-mounted, built-in tap set for bathtub. Wall-mounted, built-in tap set for shower Ø 24 Ø L L Hand shower with dedicated mixer. Spout to be ordered separately. Compatible ONLY with RINS Please add the recessed wall container for tap. Flow rate: 24,0 l/min. Hand shower and diverter. Bathtub use: water supply to overflow. Please add the recessed wall container for tap. POLISHE STAINLESS STEEL: UNTIL STOCK LASTS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Satin stainless steel..... Polished stainless steel.... RHNS15 RHNS16 Satin stainless steel..... Polished stainless steel..... RHNS13 RHNS

308 T a p s WINGS (esign Mario Tessarollo ) Taps in AISI 304 stainless steel - Finish: satin or polished. Spout for bathtub, for wall-mounted tap set. Wall-mounted, built-in tap set for bathtub / shower Ø Ø L Compatible ONLY with RHNS Flow rate: please see RHNS Please add the recessed wall container for tap. Flow rate: 14,0 l/min. POLISHE STAINLESS STEEL: UNTIL STOCK LASTS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Satin stainless steel, P 150 mm..... Polished stainless steel, P 150 mm..... Satin stainless steel, P 220 mm..... Polished stainless steel, P 220 mm..... RINS19 RINS20 RINS21 RINS22 Satin stainless steel..... Polished stainless steel..... RHNS09 RHNS10 Built-in deck-mounted tap set for bathtub. Built-in deck-mounted tap set for bathtub. Without spout Hand shower with diverter. Flow rate: 24,0 l/min. Hand shower with diverter. Flow rate: 24,0 l/min. POLISHE STAINLESS STEEL: UNTIL STOCK LASTS POLISHE STAINLESS STEEL: UNTIL STOCK LASTS Satin stainless steel..... Polished stainless steel..... RGNS01 RGNS02 Satin stainless steel..... Polished stainless steel..... RGNS03 RGNS04 Wall-mounted shower head. Ceiling-fixed shower head pair Adjustable. External installation part, white matt. Flow rate: 12,0 l/min. External installation part, white matt. Flow rate: 22,0 l/min. 24 Satin stainless steel..... RFNS03 Satin stainless steel..... RFNS

309 T a p s WINGS (esign Mario Tessarollo ) Taps in AISI 304 stainless steel - Finish: satin or polished. Ceiling-fixed shower head. Wall-mounted, recessed container for tap External installation part, white matt. Flow rate: 14,0 l/min. 1/2 connections. Satin stainless steel..... RFNS02 For RHNS RRNS01 Wall-mounted, recessed container for tap. Wall-mounted, recessed container for tap /2 connections. 1/2 connections. For RHNS RRNS07 For RHNS RRNS03 Plate for tap housing, specific for Pianura back-splash To be used ONLY for tap housing on PIANURA back-splash, in place of the recessed container. With hoses. For RHNS RRNS

310 T a p s LIQUI (esign Piero Lissoni ) Taps in chromium-plated brass. 3-holes tap set for washbasin. 3-holes tap set for bidet / Cold/warm taps with spout. 1/2 ceramic screw disks, 90 opening. Cold/warm taps with spout. 1/2 ceramic screw disks, 90 opening. Chromium-plated, spout H 183 mm.... Chromium-plated, spout H 293 mm..... RGSL02 RGSL01 Chromium-plated..... RGSL03 Wall-mounted tap pair Mixer tap for washbasin Ø46 83 Washbasin use: compatible with RISL Shower use: compatible with RFSL01. Please order the spout separately. 1/2 ceramic screw disks, 90 opening. Chromium-plated..... RGSL07 Chromium-plated..... RESL12 Mixer tap for bidet. Tall mixer tap for washbasin Ø Ø46 24 Chromium-plated..... RESL13 Chromium-plated..... RESL

311 T a p s LIQUI (esign Piero Lissoni ) Taps in chromium-plated brass. Freestanding floor-mounted mixer tap for washbasin. Freestanding floor-mounted spout Ø Ø 120 1/2 connection. 99 Chromium-plated..... RESL15 Chromium-plated, for bathtub.... Chromium-plated, for washbasin..... RISL06 RISL03 Top-mounted mixer tap for washbasin. Top-mounted spout for washbasin / /297 With hoses,3/8 connection. Compatible with RISL01-02 e RISL /8 connection. Compatible with RESL10. Chromium-plated..... RESL10 Chromium-plated, H 293 mm.... Chromium-plated, H 373 mm..... RISL04 RISL05 Wall-mounted, built-in bath/shower mixer tap. Wall-mounted, built-in bath/shower mixer tap /2 connections. With diverter. 1/2 connections. Recessed part..... Chromium-plated, external part..... RESL04I RESL04E Recessed part..... Chromium-plated, external part..... RESL05I RESL05E

312 T a p s LIQUI (esign Piero Lissoni ) Taps in chromium-plated brass. Wall-mounted spout for bathtub/washbasin. Hand shower Ø 50 Ø /2 connection. 1/2 connection. Anti-limestone membrane in silicone mm long hose. Chromium-plated, P 150 mm.... Chromium-plated, P 220 mm..... RISL01 RISL02 Chromium-plated, wall-mounted.... Chromium-plated, deck-mounted..... RJSL01 RJSL02 Wall-mounted, built-in washbasin mixer tap. Wall-mounted, built-in thermostatic bath/shower mixer tap Recessed part..... Chromium-plated, external part..... RESL11I RESL11E Recessed part..... Chromium-plated, external part..... RESL06I RESL06E Wall-mounted shower head. Wall-mounted, built-in tap set for bathtub Ø Arm included. 1/2 connection. Anti-limestone membrane in silicone. Consisting of: mixer, spout, hand shower and diverter. ogressive ceramic cartridge. 24 Chromium-plated..... RFSL01 Recessed part..... Chromium-plated, external part..... RESL07I RESL07E 24.30

313 T a p s LIQUI (esign Piero Lissoni ) Taps in chromium-plated brass. Built-in deck-mounted tap set for bathtub. Without spout. Built-in deck-mounted tap set for bathtub Cold/warm taps with 3/4 screw disks. Hand shower with dedicated mixer. Cold/warm taps with 3/4 screw disks. Spout. Hand shower with dedicated mixer. Chromium-plated..... RESL09 Chromium-plated..... RGSL08 Wall-mounted, built-in 3-way diverter. 58 Wall-mounted, built-in mixer tap for washbasin/bathtub/shower. Ø ,5 1/2 connections. Round washer. Recessed part..... Chromium-plated, external part..... RVSL01I RVSL01E Recessed part..... Chromium-plated, external part..... RESL16I RESL16E Freestanding floor-mounted bathtub tap set Ø 50 Ø 120 Consisting of: mixer, spout, hand shower and diverter. Chromium-plated..... RESL

314 T a p s W1 (esign Norbert Wangen ) Taps in AISI 304 stainless steel - Finish: satin. AVAILABLE UNTIL STOCK LASTS Top-mounted tall tap set for washbasin. Top-mounted tap set for washbasin Ø 35 Ø 54 Ø 54 Swivelling spout, adjustable aerator. Flow rate: 8,4 l/min. Swivelling spout, adjustable aerator. Flow rate: 8,4 l/min. AVAILABLE UNTIL STOCK LASTS AVAILABLE UNTIL STOCK LASTS Satin stainless steel..... REFA01 Satin stainless steel..... REFA02 Tap set for bidet. Top-mounted tap pair for washbasin Ø Ø 18 Ø 54 Flow rate: 8,4 l/min. 1/2 ceramic screw disks, 90 opening. Compatible with all top- or wall-mounted spouts. Flow rate: 12,0 l/min. AVAILABLE UNTIL STOCK LASTS AVAILABLE UNTIL STOCK LASTS Satin stainless steel..... REFA03 Satin stainless steel..... RGFA02 Wall-mounted, built-in tap set for washbasin. Wall-mounted, built-in tap set Ø Ø /2 ceramic screw disks, 90 opening. Swivelling spout. Flow rate: 8,4 l/min. AVAILABLE UNTIL STOCK LASTS 3/4 ceramic screw disks, 90 opening. Washbasin / bathtub use: compatible with all top or wall-mounted spouts. Shower use: compatible with all wall-mounted shower heads or hand-showers. Flow rate: 22,0 l/min. AVAILABLE UNTIL STOCK LASTS 24 Recessed part..... Satin stainless steel, external part..... RGFA09I RGFA09E Recessed part..... Satin stainless steel, external part..... RGFA03I RGFA03E 24.32

315 T a p s W1 (esign Norbert Wangen ) Taps in AISI 304 stainless steel - Finish: satin. AVAILABLE UNTIL STOCK LASTS Top-mounted spout. Freestanding floor-mounted spout Ø Ø Ø 55 Ø 80 Adjustable aerator. Flow rate: 8,4 l/min. Flow rate: RIFA03 8,4 l/min - RIFA04 20 l/min. AVAILABLE UNTIL STOCK LASTS AVAILABLE UNTIL STOCK LASTS Satin stainless steel, H 160 mm. For washbasin.... Satin stainless steel, H 300 mm. For washbasin.... Satin stainless steel. For bidet..... RIFA02 RIFA01 RIFA05 Satin stainless steel, H 1. For washbasin.... Satin stainless steel, H 700. For bathtub..... RIFA03 RIFA04 Wall-mounted, built-in thermostatic tap set. 80 Built-in deck-mounted tap set for bathtub. Without spout Ø With 2-way diverter. Flow rate: 22,0 l/min. Cold/warm taps with 3/4 screw disks. Hand shower with dedicated mixer. Flow rate: 22,0 l/min. AVAILABLE UNTIL STOCK LASTS AVAILABLE UNTIL STOCK LASTS Recessed part..... Satin stainless steel, external part..... RHFA01I RHFA01E Satin stainless steel..... RGFA05 Built-in deck-mounted tap set for bathtub. Wall-mounted, built-in tap set for bathtub. Ø Cold/warm taps with 3/4 screw disks. Spout. Hand shower with dedicated mixer. Flow rate: 22,0 l/min. Cold/warm taps with 3/4 screw disks. Spout. Hand shower with dedicated mixer. Flow rate: 22,0 l/min. AVAILABLE UNTIL STOCK LASTS AVAILABLE UNTIL STOCK LASTS Satin stainless steel..... RGFA06 Recessed part..... Satin stainless steel, external part..... RGFA07I RGFA07E

316 T a p s W1 (esign Norbert Wangen ) Taps in AISI 304 stainless steel - Finish: satin. AVAILABLE UNTIL STOCK LASTS Wall-mounted, built-in 5-way diverter /2 connections. AVAILABLE UNTIL STOCK LASTS Recessed part..... Satin stainless steel, external part..... RVFA01I RVFA01E

317 T a p s CUT (esign Mario Tessarollo and Tiberio Cerato ) Taps in AISI 304 stainless steel - Finish: satin. Invariable water flow and adjustable temperature. Wall-mounted, built-in washbasin mixer tap. Wall-mounted, built-in mixer for bidet / / Horizontal or vertical assembly possible. Please add the recessed wall container for tap. Flow rate: 5,7 l/min.ogressive ceramic cartridge.flow rate: 5,7 l/min. Horizontal or vertical assembly possible. Please add the recessed wall container for tap. Flow rate: 5,7 l/min. ogressive ceramic cartridge. Satin stainless steel, spout P 150 mm..... Satin stainless steel, spout P 250 mm..... RECT01 RECT02 Satin stainless steel, spout P 175 mm..... Satin stainless steel, spout P 245 mm..... RECT03 RECT04 eck-mounted, built-in bathtub tap set. eck-mounted, built-in bathtub tap set. Without spout Consisting of: mixer, spout, hand shower and diverter. Flow rate: 16,0 l/min. ogressive ceramic cartridge. Consisting of: mixer, hand shower and diverter. Flow rate: 16,0 l/min. ogressive ceramic cartridge. Satin stainless steel..... RECT07 Satin stainless steel..... RECT10 Wall-mounted, built-in tap set for bathtub. Freestanding floor-mounted bathtub tap set Consisting of: mixer, spout, hand shower and diverter. Please add the recessed wall container for tap. Flow rate: 16,0 l/min. ogressive ceramic cartridge. Consisting of: mixer, spout, hand shower and diverter. Flow rate: 16,0 l/min. ogressive ceramic cartridge. Satin stainless steel..... RECT08 Satin stainless steel..... RGCT

318 T a p s CUT (esign Mario Tessarollo and Tiberio Cerato ) Taps in AISI 304 stainless steel - Finish: satin. Invariable water flow and adjustable temperature. Wall-mounted, built-in mixer tap for shower. Wall-mounted, built-in tap set for shower Please add the recessed wall container for tap. Flow rate: 16,0 l/min. ogressive ceramic cartridge. Consisting of: mixer, spout, hand shower and diverter. Please add the recessed wall container for tap. Flow rate: 16,0 l/min. ogressive ceramic cartridge. Satin stainless steel..... RECT05 Satin stainless steel..... RECT06 Shut-off valve for cold and hot water. 45 Wall-mounted, recessed container for tap / With filters and non-return valves. Flow rate: 26,0 l/min. Horizontal or vertical assembly possible. ogressive ceramic cartridge. Template in foam polystyrene for covering fitting. 1/2 connections. Satin stainless steel..... RECT09 For RECT For RECT RRCT01 RRCT02 Wall-mounted, recessed container for tap ogressive ceramic cartridge. Template in foam polystyrene for covering fitting. 1/2 connections. 24 For RECT For RECT RRCT03 RRCT

319 T a p s UNIVERSAL ITEMS Items matchable with all Boffi collections. PV = Physical Vapour eposition. Elements in PV finish may present some tone differences. These issues cannot be considered cause for a complaint. WC flush plate. WC flush plate. With flush-mounted controls. Compatible with GEBERIT flush plates, mod. Sigma, double controls and with GEBERIT UP320, UP720. Without visible fastening elements. Compatible with GEBERIT flush plates, mod. Sigma, double controls and with GEBERIT UP320, UP720. Without visible fastening elements. Satin stainless steel.... Polished stainless steel..... Grey PV RRCT11 RRCT12 RRCT15 Satin stainless steel.... Polished stainless steel..... Grey PV RRCT13 RRCT14 RRCT16 Shower riser rail. 75 Spout for washbasin, wall-mounted or mounted on Pianura back-splash Ø Ø Shower riser rail with shower head holder. Accessories in AISI 304 stainless steel - Finishes: satin / polished / grey PV. AISI 304 stainless steel / chromium-plated brass / PV grey. Compatible with REM08, RESL10, RHNS05-06, REFP01. Flow rate: 8,6 l/min. Satin stainless steel..... Polished stainless steel..... Grey PV..... Set of 3 extensions for hoses connection. RRZZ01 RRZZ02 RRRX02 Satin stainless steel, P 150 mm..... Polished stainless steel, P 150 mm..... Chromium-plated, P 150 mm..... Grey PV, P 150 mm..... Satin stainless steel, P 220 mm..... Polished stainless steel, P 220 mm..... Chromium-plated, P 220 mm..... Grey PV, P 220 mm RINS23 RINS24 RINS27 RINS29 RINS25 RINS26 RINS28 RINS30 To be used on Pianura, with detached top and to-mounted tap. Compatible with REM08, RESL10, RHNS05-06, REFP01. Satin stainless steel..... Polished stainless steel..... RRNS05 RRNS