USB Copy Unit COM ERR. Copy. RJ-45 / USB Adapter. Verify. Read LOCK YASKAWA JVOP-181. Remote Operator Extansion Cable. Communication Option Board

Transcription

1 YSKW VZ V1000 More performance & Quality in less space Current vector control High starting torque (200% / 0.5 Hz) 1:100 speed control range Double rating ND 120%/1min and HD 150%/1 min IM&PM motor control Online Tuning Low-noise Low carrier technology 10 years lifetime design Built-in filter Screw-less terminals Control Terminals with memory backup Fieldbus communications: Modbus, Profibus, CNopen, DeviceNet, LONworks, CompoNet, Ethernet, ML-II, PROFINET and EtherCT Safety embedded: EN954-1 safety cat. 3, EN6158 SIL II and EN Stop category 0 CE, UL, cul and TUV Ratings 200 V Class single-phase 0.1 to 4 kw 200 V Class three-phase 0.1 to 15 kw 400 V Class three-phase 0.2 to 15 kw System configuration Power Supply MCCB RS232 Communications cable with PC USB Copy Unit COM ERR Input C Reactor Copy Verify Read LOCK JVOP-181 RJ-45 / USB dapter USB Cable CX-Drive CX-One Filter Remote Operator Extansion Cable LCD Remote Operator 24VDC Control Board Power Supply V1000 Communication Option Board Choke Mounting ccesories Motor Braking Resistor Ground DC reactor Output C Reactor V1000 1

2 Specifications Type designation V1000 series Z: European standard specifications : Standard specs Voltage: B: Single-phase 200 VC 2: Three-phase 200 VC 4: Three-phase 400 VC VZB0P1B Version Coating specs: : Standard Enclosure, Fin, Filter: B: IP20 without top cover F: Nema 1 E: IP20 without top cover and C3 filter [ P indicates a decimal point] Max. applicable motor output 0P1: 0.1 kw ~ 015: 15 kw 200 V class Motor kw 2 Output characteristics Power supply 400 V class Motor kw 1 Output characteristics Power supply Single-phase: VZ@ B0P1 B0P2 B0P4 B0P7 B1P5 B2P2 B4P Only HD settings is available for this model 2. Based on a standard 4-pole motor for maximum applicable motor output: Heavy Duty (HD) mode with a 150% overload capacity Normal Duty (ND) mode with a 120% overload capacity Three-phase: VZ@ 20P1 20P2 20P4 20P7 21P5 22P2 24P0 25P5 27P For HD setting For ND setting Inverter capacity kv Rated output current () at HD Rated output current () at ND Max. output voltage Proportional to input voltage: V Max. output frequency 400 Hz Rated input voltage and frequency llowable voltage fluctuation llowable frequency fluctuation Single-phase V 50/60 Hz 3-phase V 50/60 Hz -15%..+10% Three-phase: VZ@ 40P2 40P4 40P7 41P5 42P2 43P0 44P0 45P5 47P For HD setting For ND setting Inverter capacity kv Rated output current () at HD Rated output current () at ND Max. output voltage V (proportional to input voltage) Max. output frequency 400 Hz Rated input voltage and frequency 3-phase VC, 50/60 Hz llowable voltage fluctuation llowable frequency fluctuation 1. Based on a standard 4-pole motor for maximum applicable motor output: Heavy Duty (HD) mode with a 150% overload capacity Normal Duty (ND) mode with a 120% overload capacity +5% -15%..+10% +5% 2 Frequency inverters

3 Specifications Common specifications Control functions Functionality Protection functions mbient conditions Model number Specifications Control methods Sine wave PWM (V/f control, sensorless current vector control) Output frequency range Hz Frequency tolerance Digital set value: ±0.01% ( ºC) nalogue set value: ±0.1% (25 ±10 ºC) Resolution of frequency set value Digital set value: 0.01 Hz (<100 Hz), 0.1 Hz (>100 Hz) nalogue set value: 1/1000 of maximum frequency Resolution of output frequency 0.01 Hz Overload capability Heavy duty use: 150% rated output current for one minute Normal duty use: 120% rated output current for one minute Frequency set value V (20 k ), m (250 ), m (250 ) Pulse train input, frequency setting value (selectable) Braking torque Short-term average deceleration torque: 150% (up 1.5 kw), 100% (for 1.5 kw), 50% (for 2.2 kw), 20% (for bigger size) (short term peak torque) Continuous regenerative torque: pprox 20% (125% with optional braking resistor, 10%ED, 10 s, braking transistor built in) V/f Characteristics Possible to program any V/f pattern Seven of the following input signals are selectable: Forward/reverse run (3-wire sequence), fault reset, external fault (NO/NC Inputs signals contact input), multi-step speed operation, Jog command, accel/decel time select, external baseblock, speed search command, UP/DOWN command, accel/decel hold command, LOCL/REMOTE selection, communication/control circuit terminal selection, emergency stop fault, emergency stop alarm, self test Following output signals are selectable (NO/NC contact output, 2 photo-coupler outputs): Fault, running, zero speed, speed Output signals agree, frequency detection (output frequency <= or => set value), during overtorque detection, minor error, during baseblock, operation mode, inverter run ready, during fault retry, during undervoltage detection, reverse running, during speed search, data output through communication. Open-loop vector control, full-range automatic torque boost, slip compensation, 17-step speed operation (max.), restart after momentary power loss, DC injection braking current at stop/start (50% of inverter rated current, 0.5 sec, or less), frequency Standard functions reference bias/gain, MEMOBUS communications (RS-485/422, max. 115K bps), fault retry, speed search, frequency upper/ lower limit setting, overtorque detection, frequency jump, accel/decel time switch, accel/decel prohibited, S-curve accel/decel, PID control, energy-saving control, constant copy. nalogue inputs 2 analogue inputs, V, m, m Braking/acceleration times s Display Optionally frequency, current or set value Error and status LED Motor overload protection Instantaneous overcurrent Overload Overvoltage Undervoltage Momentary power loss Cooling fin overheat Stall prevention level Ground fault Electronic thermal overload relay Motor coasts to a stop at approx. 250% of inverter rated current Heavy Duty: Motor coasts to a stop after 1 minute at 150% of inverter rated output current Normal Duty: Motor coasts to a stop after 1 minute at 120% of inverter rated output current Motor coasts to a stop if DC bus voltage exceed 410 V (double for 400 V class) Stops when DC bus voltage is approx. 190 V or less (double for 400 V class) (approx. 150 V or less for single-phase series) Following items are selectable: not provided (stop if power loss is 15 ms or longer), continuous operation if power loss is approx. 0.5 s or shorter, continuous operation Protected by thermistor Stall prevention during acceleration/deceleration and constant speed operation Protected by electronic circuit (operation level is approx. 250% of rated output current) Power charge indication Indicates until the main circuit voltage reaches 50 V. Degree of protection IP20, NEM1 Cooling Cooling fan is provided for 200 V, 0.75 kw (1HP) (3/single-phase) 400 V, 1.5 kw (2HP) (3-phase), others are self-cooling mbient humidity 95% RH or less (without condensation) Storage temperature -20 ºC..+60 ºC (short-term temperature during transportation) Installation Indoor (no corrosive gas, dust, etc.) Installation height Max m Vibration Up to 9.8 m/s 2 at 10 to less than 20 Hz, Up to 6.37 m/s 2 at 20 to 50 Hz V1000 3

4 Dimensions IP20 type Figure 1 Figure 2 W1 2-M4 t1 W1 4-M4 W H1 H2 H D D1 W H2 H1 H D D1 t1 Voltage class Single-phase 200 V Three-phase 200 V Three-phase 400 V Dimensions in mm Max. applicable motor output kw Inverter model VZ@ Figure W1 H1 W H D t1 H2 D1 H3 H B0P B0P B0P B0P B1P B2P B4P P P P P P P P P P P P P P P P P P P Weight kg V Option board (Communication and 24 VDC power supply) Communication option boards PS-V10S PS-V10M 24 VDC Power supply Options 4 Frequency inverters

5 Built-in filter Dimensions in mm W H H1 D1 D2 D B0P1 B0P B0P B0P B1P B2P P P P P P P0 44P Schaffner footprint filters Fig 1 Fig 2 C G I C E M I L B F H J L B F N J H K D E G K D Schaffner standard model Fig Dimensions in mm B C D E F G H I J K L M N 1000-FIV1010-SE M M FIV1020-SE M M V 1000-FIV1030-SE M M FIV1040-SE M M FIV2010-SE-V M M FIV2020-SE M M FIV2030-SE M M V 1000-FIV2060-SE-V M M FIV2080-SE-V M M FIV2100-SE-V M M FIV3005-SE M M FIV3010-SE M M V 1000-FIV3020-SE M M FIV3030-SE-V M M FIV3050-SE-V M M Weight kg V1000 5

6 Schaffner low leakage model V V V Fig Dimensions in mm B C D E F G H I J K L 1000-FIV1010-SE-LL M M FIV1020-SE-LL M M FIV1030-SE-LL M M FIV1040-SE-LL M M FIV2010-SE-LL M M FIV2020-SE-LL M M FIV2030-SE-LL M M FIV3005-SE-LL M M FIV3010-SE-LL M M FIV3020-SE-LL M M FIV3030-SE-LL M M FIV3050-SE-LL M M Weight kg Rasmi footprint filters 1x200 V 3x200 V 3x400 V Rasmi standard and low leakage model Dimensions in mm W H L X Y M 1000-FIV1010-RE@ M FIV1020-RE@ M FIV1030-RE@ M FIV1040-RE@ M FIV2010-RE@ M FIV2020-RE@ M FIV2030-RE@ M FIV2060-RE@ M FIV2080-RE@ M FIV2100-RE@ M FIV3005-RE@ M FIV3010-RE@ M FIV3020-RE@ M FIV3030-RE@ M FIV3050-RE@ M5 2.8 Weight kg Remote LCD operator (0.06) (0.48) Installation holes (2-M3 screws, depth 5 (0.19)) 90 (3.54) 78 (3.07) <1> 15 (0.59) 60 (2.36) 7.9 (0.31) minimum 50 (1.96) 44 (1.73) Unit : mm (in) 6 Frequency inverters

7 Input C Reactor Single-phase Voltage 200 V Dimensions B C D E F G H Weight kg X-RI DE X-RI DE X-RI DE X-RI DE Three-phase Voltage 200 V 400 V Dimensions B2 C2 D E F Weight kg X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE DC Reactor Voltage 200 V 400 V Dimensions Weight B C D E F G H kg X-RC DE X-RC DE X-RC DE X-RC DE 1.60 X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE 105 X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE V1000 7

8 Output C Reactor Voltage 200 V 400 V Dimensions Weight B2 C2 D E F kg X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE Chokes Description D Motor Dimensions in mm Weight diameter KW L W H X Y m kg X-FER2102-RE 21 < X-FER2515-RE 25 < X-FER5045-RE 50 < W Y X L Ø m H Ø d Resistor Dimensions X-REM00K15xxx Fig 1 Fig Type Fig. Dimensions in mm Weight L H M I T G N kg X-REM00K1400-IE X-REM00K2070-IE X-REM00K2120-IE 1 X-REM00K2200-IE X-REM00K4035-IE X-REM00K6035-IE X-REM00K9020-IE X-REM00K9017-IE Frequency inverters

9 DIN rail mounting bracket EZZ08122 EZZ08122B 35.1 DIN rail Four, M4 tap Side view (common to all the units) Four, M4 tap EZZ08122C EZZ08122D Four, M4 tap Four, M4 tap Inverter DIN rail mounting bracket 1-phase 200 VC B0P1/ B0P2/ B0P4 EZZ08122 B0P7/ B1P5 EZZ08122B B2P2 EZZ08122C B4P0 EZZ08122D 3-phase 200 VC 20P1/ 20P2 / 20P4/ 20P7 EZZ P5/ 22P2 EZZ08122B 24P0 EZZ08122C 3-phase 400 VC 40P2/ 40P4/ 40P7/ 41P5/ 42P2 EZZ08122B 44P0 EZZ08122C V1000 9

10 Heatsink attachment and Panel cut dimensions Heatsink External Mounting ttachment Mounting Panel D3 for more Fig Dia. Holes Fig 2 Fig 3 Fig 4 4-d Tap 1X200 V 3x200 V 3X400 V VZ@ Frame Panel Cutting W H W1 H1 D1 D2 D3 Fig (W2) (W3) (H2) (H3) B B0P B0P B0P B0P B1P B2P B4P P P P P P P P P P P P P P P P0 44P P P Frequency inverters

11 Installation Standard connections For 1-phase power supply use R/L1 and S/L2 DC reactor (option) Link Thermal relay Braking resistor (opt) Power Supply L1 L2 L3 Fuses Filter R/L1 S/L2 T/L B1 B2 V1000 U/T1 V/T2 W/T3 U V W M Main Switch Forward/Stop Reverse/Stop S1 S2 Shielded Cable External Fault S3 Ground Fault Reset S4 Multi-speed 1 S5 Multi-speed 2 S6 +24 V 8 m Multi-function digital inputs (default setting) 2 kw SC RP +V 1 2 C DIP switch S3 SINK SOURCE 24 V 0V Shielded ground terminal Pulse Input (max. 32kHz) nalog input power supply VDC, max. 20 m Multi-function analog input 1 0 to 10 V (20 kw) Multi-function analog input 2 0 to 10 V (20 kw) or 0/4 to 20 m (250 W) M MB MC P1 P2 PC MP M C Fault During run Multi-function relay output 250 Vac / 30 VDC (10 m to 1) (default setting) Frequency agree Photocoupler common Pulse train output (max. 32 khz) (Output frequency) nalog output 0 to +10 VDC (2m) (Output frequency) Multi-function photocoupler output 48 VDC, max. 50 m (default setting) Monitor outputs (default setting) Multi- function pulse / analog inputs (default: frequency reference) Terminal resistance (120 W, 1/2 W) R+ Safe Disable inputs H2 H1 R S+ S Memobus comm. RS-485/422 max. 115 kbps HC IG Symbols: Use twisted pair cables Use shielded twisted pair cables Indicates a main circuit terminal Indicates a control circuit terminal. V

12 Main circuit Terminal Name Function (signal level) R/L1, S/L2, T/L3 Main circuit power supply input Used to connect line power to the drive. Drives with single-phase 200 V input power use only terminals R/L1 and S/L2 (T/L3 is not connected to anything) U/T1, V/T2, W/T3 Inverter output Used to connect the motor B1, B2 Braking resistor connection vailable for connecting a braking resistor or the braking resistor unit option. +2, +1 DC reactor connection Remove the short bar between +2 and +1 when connecting DC reactor (option) +1, DC power supply input For power supply input (+1: positive electrode; : negative electrode) Grounding For grounding (grounding should conform to the local grounding code.) Control Circuit Type No. Signal name Function Signal level S1 Multi-function input selection 1 Factory setting: runs when CLOSED, stops when OPEN. Digital input signals nalog input signals Fast Stop Cmd Digital output signals S2 Multi-function input selection 2 Factory setting: runs when CLOSED, stops when OPEN. S3 Multi-function input selection 3 Factory setting: External Fault (N.O.) S4 Multi-function input selection 4 Factory setting: Fault reset S5 Multi-function input selection 5 Factory setting: Multi-step speed cmd 1 S6 Multi-function input selection 6 Factory setting: Multi-step speed cmd 2 SC Multi-function input selection Common Common for control signal RP FS FR1 FR2 Main Speed Cmd Pulse Train Input 32 khz max. Power Supply for Frequency Setting +10 V (allowable max current 20 m) Main Speed Freq Ref FC Frequency reference common 0V Voltage input or current input 0 to +10 VDC (20 k ) (resolution 1/1000) 4 to 20 m (250 ) or 0 to 20 m (250 ) Resolution: 1/500 HC Power Supply Fast Stop Cmd +24 V (max allowable current 10 m) H1 H2 M MB MC Special Digital input Special Digital input NO contact output NC Output Relay Output common Open: Fast Stop Factory setting: fault P1 Photocoupler output 1 Factory setting: During run Closed: Normal Operation P2 Photocoupler output 2 Factory setting: Frequency gree PC Photocoupler output common 0V 24 VDC, 8 m photocoupler insulation Contact capacity 250 VC, 1 or less 30 VDC, 1 or less Photocoupler output: +48 VDC, 50 m or less nalog output signals PM Pulse train Output max 33 khz M nalog monitor output Factory setting: "output frequency" 0 to +10 V output Resolution: 1/ to 10 V 2 m or less C nalog monitor common 0V Resolution: 8 bits R+ Communication input (+) RS-485/422 R Communication input ( ) S+ Communication output (+) S Communication output ( ) For MEMOBUS communication operation by RS-485 or RS-422 communication is available. RS-485/422 MEMOBUS protocol 12 Frequency inverters

13 a a: Space required differs by model: Up to 3.7 kw: minimum 30 mm 5.5 kw and above: minimum 50 mm a t least 100 mm irflow Side by Side mounting t least 100 mm Inverter heat loss Single-phase 200 V class Heat loss W HD Heat loss W ND Model VZ B0P1 B0P2 B0P4 B0P7 B1P5 B2P2 B4P0 Inverter capacity kv Rated current () at HD Rated current () at ND Fin Inside unit Total heat loss Fin Inside unit Total heat loss Cooling Method Self Cooled Fan Cooled Three-phase 200 V class Heat loss W HD Heat loss W ND Model VZ 20P1 20P2 20P4 20P7 21P5 22P2 24P0 25P5 27P Inverter capacity kv Rated current () at HD Rated current () at ND Fin Inside unit Total heat loss Fin Inside unit Total heat loss Cooling Method Self Cooled Fan Cooled Three-phase 400 V class Heat loss W HD Heat loss W ND Model VZ 40P2 40P4 40P7 41P5 42P2 43P0 44P0 45P5 47P Inverter capacity kv Rated current () at HD Rated current () at ND Fin Inside unit Total heat loss Fin Inside unit Total heat loss Cooling Method Self Cooled Fan Cooled V

14 Connections for braking resistor Thermal relay Braking resistor Power supply MCCB MC R/L1 B1 B2 S/L2 T/L3 U/T1 V/T2 Motor THRX OFF ON MC S MC THRX VZ W/T3 S Thermal relay switch for external braking resistor MC TRX FLT- S TRX FLT-B Fault contact Input C Reactor C reactor VZ Power supply MCCB U X R/L1 V Y S/L2 W Z T/L3 Max. applicable motor output kw 1 phase 200 V class 3 phase 200 V class 400 V class Max. applicablplicable Max. ap- Current Inductance Current Inductance value motor value motor output mh output kw mh kw Current value 0.4 X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE X-RI DE Inductance mh DC Reactor Power supply MCCB R/L1 VZ S/L2 T/L V class 400 V class Current value Inductance mh Max. applicable motor output kw Current value 0.2 X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE X-RC DE Max. applicable motor output kw Output C Reactor DC reactor Inductance mh 200 V class 400 V class Max. applicable Current value Inductance Max. applicable Current value Inductance motor output kw mh motor output kw mh 0.4 X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE X-RO DE Frequency inverters

15 Safety System V1000 safe stop application using OMRON G9SB safety relay unit complies to safety category 3 according EN / Stop category 0 according EN60204 Ensure V1000 and safety relay are mounted in the same cabinet to exclude cross circuit between H1 and H2 Start 1 2 T11 T12 T31 T TH S K1 K1 a K2 K2 a K2 K1 Control Circuit K1 K2 T21 T Multi-function digital inputs Power B1 B2 Supply DC reactor Braking R/L1 resistor S/L2 V1000 T/L3 S1 U/T1 V/T2 W/T3 Ground S2 S3 S4 S5 S6 +24 V 8 m MF relay output M SC DIP switch S3 SINK SOURCE 24 V MB MC MF photo-coupler output P1 0V RP +V 1 2 C H2 H1 Shielded ground terminal Pulse Input (max. 32kHz) nalog input PS VDC, max. 20 m MF nalog input 1 0 to 10 V (20 kw) MF nalog input 2 0 to 10 V (20 kw) or 0/4 to 20 m (250 W) Safe Disable inputs P2 PC MP Pulse train output M C nalog output 0 to +10 VDC (2m) Terminal resistance# (120 W, 1/2 W) R+ R- S+ S- HC RS-485/422 IG V

16 YSKW Ordering information Power Supply C MCCB RS232 Communications cable with PC Input C Reactor Filter Copy Verify Read LOCK USB Copy Unit COM ERR JVOP-181 C RJ-45 / USB dapter C Remote Operator Extansion Cable C USB Cable C LCD Remote Operator D CX-Drive CX-One C 24VDC Control Board Power Supply V1000 B Communication Option Board Choke Motor F Mounting ccesories E Braking Resistor Ground DC reactor Output C Reactor V1000 1x200 V 3x200 V 3x400 V Specifications Model Heavy Duty Normal Duty Standard Built-in filter 0.12 kw kw 0.8 VZB0P1B VZB0P1EB 0.25 kw kw 1.6 VZB0P2B VZB0P2EB 0.55 kw kw 3.5 VZB0P4B VZB0P4EB 1.1 kw kw 6.0 VZB0P7B VZB0P7EB 1.5 kw kw 9.6 VZB1P5B VZB1P5EB 2.2 kw kw 12.0 VZB2P2B VZB2P2EB 4.0 kw kw 21.0 VZB4P0B kw kw 0.8 VZ20P1B kw kw 1.6 VZ20P2B kw kw 3.5 VZ20P4B kw kw 6.0 VZ20P7B kw kw 9.6 VZ21P5B kw kw 12.0 VZ22P2B kw kw 21.0 VZ24P0B kw kw 30.0 VZ25P5F kw kw 40.0 VZ27P5F - 11 kw kw 56.0 VZ2011F - 15 kw kw 69.0 VZ2015F kw kw 1.2 VZ40P2B VZ40P2EB 0.55 kw kw 2.1 VZ40P4B VZ40P4EB 1.1 kw kw 4.1 VZ40P7B VZ40P7EB 1.5 kw kw 5.4 VZ41P5B VZ41P5EB 2.2 kw kw 6.9 VZ42P2B VZ42P2EB 3.0 kw kw 8.8 VZ43P0B VZ43P0EB 4.0 kw kw 11.1 VZ44P0B VZ44P0EB 5.5 kw kw 17.5 VZ45P5F kw kw 23.0 VZ47P5F - 11 kw kw 31.0 VZ4011F - 15 kw kw 38.0 VZ4015F - 16 Frequency inverters

17 Line filters Voltage 1-Phase 200 VC 3-Phase 200 VC 3-Phase 400 VC Inverter Model 1000-FIV Standard line filter Low leakage line filter Schaffner Rasmi Schaffner Rasmi Current () 1000-FIV Current () 1000-FIV Current () 1000-FIV Current () B0P1 / B0P2 / B0P SE RE SE-LL RE-LL 10 B0P7 / B1P SE RE SE-LL RE-LL 20 B2P SE RE SE-LL RE-LL 30 B4P SE RE SE-LL RE-LL 40 20P1 / 20P2 / 20P4 / 20P SE-V RE SE-LL RE-LL 10 21P5 / 22P SE RE SE-LL RE-LL 16 24P SE RE SE-LL RE-LL 26 25P5 / 27P SE-V RE RE-LL SE-V RE RE-LL SE-V RE RE-LL P2 / 40P SE RE SE-LL RE-LL 5 40P7 / 41P5 / 42P2 / 43P SE RE SE-LL RE-LL 10 44P SE RE SE-LL RE-LL 15 45P5 / 47P SE-V RE SE-LL RE-LL / SE-V RE SE-LL RE-LL 50 Input C reactors Inverter C Reactor Voltage Model VZ@ B0P1 / B0P2 / B0P4 X-RI DE B0P7 X-RI DE 1-Phase 200 VC B1P5 X-RI DE B2P2 X-RI DE B4P0-20P1 / 20P2 / 20P4 / 20P7 X-RI DE 3-Phase 200 VC 21P5 / 22P2 / 24P0 X-RI DE 25P5 / 27P5 X-RI DE 2011 / 2015 X-RI DE 40P2 / 40P4 / 40P7 / 41P5 X-RI DE 3-Phase 400 VC 42P2 / 43P0 / 44P0 X-RI DE 45P5 / 47P5 X-RI DE 4011 / 4015 X-RI DE DC reactors 200V 1-phase 200V 3-phase 400V 3-phase Model VZ@ DC Reactor Model VZ@ DC Reactor Model VZ@ DC Reactor B0P1 20P1 40P2 / 40P4 X-RC DE X-RC DE X-RC DE B0P2 20P2 40P7 X-RC DE B0P4 X-RC DE 20P4 X-RC DE 41P5 X-RC DE B0P7 X-RC DE 20P7 X-RC DE 42P2 X-RC DE B1P5 X-RC DE 21P5 X-RC DE 43P0 X-RC DE B2P2 X-RC DE 22P2 X-RC DE 44P0 X-RC DE B4P0-24P0 X-RC DE 45P5 X-RC DE - 25P5 X-RC DE 47P5 X-RC DE 27P5 X-RC DE 4011 X-RC DE 2011 X-RC DE 4015 X-RC DE 2015 X-RC DE - V

18 Chokes Model Diameter Description X-FER2102-RE 21 For 2.2 KW motors or below X-FER2515-RE 25 For 15 KW motors or below X-FER5045-RE 50 For 45 KW motors or below Output C reactor Inverter C Reactor Voltage Model VZ@ 200 VC 400 VC B0P1 / B0P2 / B0P4 20P1 / 20P2 / 20P4 X-RO DE B0P7 / 20P7 X-RO DE B1P5 / 21P5 X-RO DE B2P2 / 22P2 X-RO DE B4P0 / 24P0 X-RO DE 25P5 X-RO DE 27P5 X-RO DE 2011 X-RO DE 2015 X-RO DE 40P2 / 40P4 / 40P7 / 41P5 X-RO DE 42P2 X-RO DE 43P0 / 44P0 X-RO DE 45P5 X-RO DE 47P5 X-RO DE 4011 X-RO DE 4015 X-RO DE B Communication cards Type Model Description Function Used for running or stopping the inverter, setting or referencing parameters, and monitoring SI-N3/V DeviceNet option card output frequency, output current, or similar items through DeviceNet communication with the host controller. Used for running or stopping the inverter, setting or referencing parameters, and monitoring SI-P3/V PROFIBUS-DP option card output frequency, output current, or similar items through PROFIBUS-DP communication with the host controller. Used for running or stopping the inverter, setting or referencing parameters, and monitoring SI-S3/V CNopen option card output frequency, output current, or similar items through CNopen communication with the host controller. Communication option board C ccessories SI-T3/V EUOP-SI-ES3/V SI-EP3/V MECHTROLINK-II option card EtherCT option card PROFINET option card Used for running or stopping the inverter, setting or referencing parameters, and monitoring output frequency, output current, or similar items through MECHTROLINK-II communication with the host controller. Used for running or stopping the inverter, setting or referencing parameters, and monitoring output frequency, output current, or similar items through EtherCT communication with the host controller. Used for running or stopping the inverter, setting or referencing parameters, and monitoring output frequency, output current, or similar items through PROFINET communication with the host controller. Types Model Description Functions JVOP-180 LCD remote operator LCD Display operator with language support Digital operator 1000-CVOP300-EE Remote operator cable 3 meters cable for connecting remote operator JVOP-181 USB converter / USB cable USB converter unit with copy and backup function ccessories PS-V10S 24VDC control board power supply VZ-B/2/4 from 0.1 to 4 KW 24 VDC option board PS-V10M 24VDC control board power supply VZ-2/4 from 5.5 to 15 KW 1000-CVPC232-EE PC connection cable RS232 PC tool connection cable D Computer software Types Model Description Installation Software CX-Drive Computer software Configuration and monitoring software tool CX-One Computer software Configuration and monitoring software tool 18 Frequency inverters

19 E Braking unit, braking resistor unit Voltage 200 V (single-/ three-phase) 400 V (three-phase) Max. motor kw Inverter Braking resistor unit Inverter model VZ@ Inverter mounted type Connectable min. (3 %ED, 10 sec max) Braking resistance torque % 1-phase 3-phase Type X- Resist 0.12 B0P1 20P REM00K1400-IE B0P2 20P B0P4 20P REM00K1200-IE B0P7 20P B1P5 21P REM00K2070-IE B2P2 22P B4P0 24P P5 16 REM00K4035-IE P REM00K6035-IE REM00K9017-IE P P4 2 x REM00K1400-IE P P5 240 REM00K1400-IE P2 200 REM00K2200-IE P REM00K2120-IE P P REM00K4035-IE P REM00K6035-IE REM00K9020-IE ss sf Mounting accessories Types Model Description pplicable models VZ@ DIN Rail EZZ08122 EZZ08122B EZZ08122C Necessary to mount the inverter on a DIN rail B0P1/B0P2/B0P4 20P1/20P2/20P4/20P7 B0P7/B1P5 21P5/22P2 40P2/40P4/40P7/41P5/42P2 B2P2 24P0 44P0 EZZ08122D B4P0 B0P1/B0P2 20P1/20P2 B0P4 20P P7 Heatsink external mounting attachment P dditional items to mount the inverter with the heatshink out of the panel B1P5 21P5/22P2 41P5/42P2/43P0 B2P2 24P0 44P B4P B0P7 40P2/40P4 25P5/27P5 45P5/47P / V

20 LL DIMENSIONS SHOWN RE IN MILLIMETERS. To convert millimeters into inches, multiply by To convert grams into ounces, multiply by Cat. No. I68E-EN-03D In the interest of product improvement, specifications are subject to change without notice. 20 Frequency inverters