Bulkhead Connections for Series B 1326 Cables

Transcription

1 nstallation nstructions ulkhead onnections for Series ables atalog Numbers -U-, -U-L, -UT-L, -UT-, -P-, -P-L, -PT-L, -PT-, -P-, -P-L, -PT-L, -PT- bout This Publication This publication contains installation information for cables that have or connect to bulkhead connectors. This includes cables with bulkhead connectors, push-pull connectors, flying leads, and combinations of these connection types. The table lists available Series bulkhead cables and the cables they obsolete. This cable replaces -U-L-xxx -UT-L-xxx -P-L-xxx -PT-L-xxx -P-L-xxx -PT-L-xxx this cable. -U--xxx -U--xxx, -U-L-xxx, -UT--xxx -P--xxx -P--xxx, -P-L-xxx, -PT--xxx -P--xxx -P--xxx, -P-L-xxx, -PT--xxx Publication -N0-N-P - May 00

2 ulkhead onnections for Series ables eedback able Wiring wiring pinouts and diagrams are provided for the -Ux-x and -UT-x feedback cables. Refer to page for power cable information, and page for installation instructions. -Ux-x-xxx Wiring This table provides wiring information for the -Ux-x-xxx cables. Signal Wire olor auge mm (W) -U--xxx able Wiring iagram -U- xis_0_r lack 0. (0) xis_0_r White 0. (0) 0. (0) xis_0_s lack 0. (0) xis_0_s Red 0. (0) 0. (0) xis_0_s lack 0. (0) xis_0_s reen 0. (0) 0. (0) -UT-L Overall shield N/ Shell and Shell Male Pair #: lack Pair #: White Pair #: lack Pair #: Red Pair #: lack Pair #: reen ulkhead Publication -N0-N-P - May 00

3 ulkhead onnections for Series ables -UT-L-xxx able Wiring iagram Male Pair #: lack Pair #: White Pair #: lack Pair #: Red Pair #: lack Pair #: reen ulkhead -Ux-x-xxx Wiring This table provides wiring information for the -Ux-x-xxx cables. Signal Wire olor auge mm (W) -UT- Terminal Number xis_0_r lack 0. (0) xis_0_r White 0. (0) 0. (0) xis_0_s lack 0. (0) xis_0_s Red 0. (0) 0. (0) xis_0_s lack 0. (0) xis_0_s reen 0. (0) 0. (0) Overall shield N/ 0 -UT-L Publication -N0-N-P - May 00

4 ulkhead onnections for Series ables -U-L-xxx able Wiring iagram Pair #: lack Pair #: White Pair #: lack Pair #: Red Pair #: lack Pair #: reen -UT--xxx able Wiring iagram ulkhead Male Pair #: lack Pair #: White Pair #: lack Pair #: Red Pair #: lack Pair #: reen ulkhead ulkhead Power able Wiring wiring pinouts and diagrams are provided for the -Px-x and -x-x power cables. Refer to page for feedback cable information, and page for installation instructions. TTNTON The dc bus capacitors in a drive retain hazardous voltages after input power has been removed. efore beginning work on the output power cable from any drive system, measure the bus voltage at the drive to verify it has reached a safe level or wait the full time interval indicated in the warning label on the front of the drive. ailure to observe this precaution could result in severe bodily injury or loss of life. MPORTNT o not coil a power cable on itself. eat may buildup in a closely coiled power cable and result in degradation of the cable insulation. Publication -N0-N-P - May 00

5 ulkhead onnections for Series ables -P--xxx, -PT-L, -P--xxx and -PT-L Wiring This table provides wiring information for the -Px-x-xxx cables. Wire Number Signal Wire olor -Px auge mm (W) -Px auge mm (W) -Px- Male Power lack. (). (0) Power lack. (). (0) Power lack. (). (0) Power lack. (). () Power lack. (). () Power lack. (). () N reen/yellow. ().0 () rake lack. ().0 () Overall shield. (). () -P--xxx and -P--xxx able Wiring iagram -PxT-L Overall shield raid N/ N/ N/ onnected to shell Male ulkhead Wire # Wire # Wire # Wire # Wire # Wire # reen/yellow Wire# -PT-L-xxx and -PT-L-xxx able Wiring iagram Male Wire # Wire # Wire # Wire # Wire # Wire # reen/yellow Wire# Publication -N0-N-P - May 00

6 ulkhead onnections for Series ables -Px-x-xxx and -Px-x-xxx Wiring This table provides wiring information for the -Pxx-x-xxx cables. Wire Number Signal Wire olor auge mm (W) for -Px auge mm (W) for-px -PxT- and Male Power lack. (). (0) U Power lack. (). (0) V Power lack. (). (0) W rake lack. (). () T- Thermostat lack. (). () T- rake lack. (). () T- Overall shield. ().0 () P N) reen/yellow. ().0 () P Thermostat lack. (). () T- -PT--xxx and -PT--xxx able Wiring iagram -Px-L Overall shield raid N/ N/ round stud onnected to shell Male Wire # Wire # Wire # Wire # Wire # Wire # reen/yellow Wire# ulkhead -P-L-xxx and -P-L-xxx able Wiring iagram Wire # Wire # Wire # Wire # Wire # Wire # reen/yellow Wire# ulkhead Publication -N0-N-P - May 00

7 ulkhead onnections for Series ables able outs The diagrams show the cable pin locations for female or male connectors. ulkhead outs LLN-RLY LLN-RLY Male ulkhead ulkhead Push-pull Male Push-pull -P -P -S -P Push-pull outs LLN-RLY LLN-RLY Male ulkhead Push-pull P able end Radius The table and diagram depict the minimum bend radius (R) for cables. end radius is the tightest (minimum) curvature allowed without potential damage to the cable. Motor Power able atalog Number R, pprox mm (in.) () end Radius iagram -Ux-x-xxx and -Ux-x-xxx 0. (.0) -Px-x-xxx and -Px-x-xxx 0. (.) -Px-x-xxx, and -Px-x-xxx 0. (.) end Radius () end radius (R) is the specified minimum bend radius for cable assemblies. or non-flex cables, R is a one-time flex application. lex cables have a much higher R to withstand flex applications. The R for user-fabricated cables may vary. R Publication -N0-N-P - May 00

8 ulkhead onnections for Series ables nstalling Push-pull and ulkhead s The -xxxt--xxx connector has male pins at one end and female contacts on the other end. WRNN ll series cable connectors are treated with a black, highly-conductive, cobalt coating. o not scrape this coating. uidelines for onnecting ables with Push-pull and ulkhead s LLN-RLY LLN-RLY Push-pull ulkhead These guidelines apply to push-pull and bulkhead cable connections. push-pull connector can connect only to a bulkhead connector or a 0V-x motor. bulkhead connector can connect only to a push-pull connector. One connector must have male pins and the connector it mates with must have female contacts. ables designated with the L option can connect to cables or motors without this option, but the resulting connection does not provide the L option. The length of a cable run cannot exceed 0 m ( ft.). Publication -N0-N-P - May 00

9 - ulkhead onnections for Series ables nstalling ulkhead ssemblies The diagram shows the bulkhead connector. The side view shows the fastening screws for the bulkhead connector protruding from its flange, and passing through the conductive metal cabinet. The front view shows the orientation of the pins and fastening screws on the bulkhead connector Outline of the mating connector ront view onductive (metal) wall Side view Overmold, black pvc Required Tools You will need these tools to install a bulkhead connection: Phillips screwdriver rill and drill bits Mounting imensions The table provides hole dimensions for the five mounting holes. able Screw escription iameter of Mounting oles, pprox. mm (in.) istance etween enters of Mounting oles, pprox. mm (in.) iameter of, pprox. mm (in.) iameter of Opening, pprox. mm (in.) -U--xxx /0 / in.. (0.). (.0). (.) 0. (.) -Ux-x-xxx /0 / in.. (0.). (.0). (.) 0. (.) -P--xxx /0 / in.. (0.). (.). (.). (.) -Px-x-xxx /0 / in.. (0.). (.). (.). (.) -P--xxx / / in..0 (0.0). (.). (.). (.) -Px-x-xxx / / in..0 (0.0). (.). (.). (.) Publication -N0-N-P - May 00

10 0 ulkhead onnections for Series ables iameter of connector opening istance between centers of mounting holes iameter of mounting holes Wall surface MPORTNT You do not need to attach the bulkhead cables to a cabinet wall, but you do need to follow the information in uidelines for onnecting ables with Push-pull and ulkhead s on page. ulkhead connector diameter Wall's opening for diameter of connector Maximum width of cabinet wall. mm (0. in) nstalling a ulkhead through a abinet Wall The recommended connection method will result in a connector seal at the cabinet wall equivalent to an P rating. ollow these steps to prepare a cabinet wall for mounting the bulkhead connector. Publication -N0-N-P - May 00

11 ulkhead onnections for Series ables. Locate the area of the cabinet wall where you will mount the bulkhead connector. TTNTON To avoid a shock hazard, remove power to the motor controller and motor before installing or removing cables. ailure to do this can cause personal injury. The power rail must be mounted with the connectors in an upright or vertical orientation to the panel. This provides proper cooling of the modules. o not mount modules if the power rail is not within of vertical.. Mark the places where the four mounting holes and the center connector opening, a total of five holes, will be located.. rill the four mounting holes and the large center opening.. Scrape any paint from the inside surface of the cabinet wall where the bulkhead flange of the -P-L-xxx or -P-L-xxx cables will make contact. MPORTNT metal-to-metal connection is required for compliance.. Remove the viton seal from the face of the connector for -Ux-x-xxx, -Px-x-xxx, and -Px-x-xxx cables to provide clearance for the cabinet wall.. ttach the bulkhead connector through the wall, as shown. Maximum width of cabinet wall. mm (0. in.) Publication -N0-N-P - May 00

12 Rockwell utomation Support Rockwell utomation provides technical information on the Web to assist you in using its products. t you can find technical manuals, a knowledge base of Qs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools. or an additional level of technical phone support for installation, configuration, and troubleshooting, we offer Techonnect Support programs. or more information, contact your local distributor or Rockwell utomation representative, or visit nstallation ssistance f you experience a problem with a hardware module within the first hours of installation, please review the information that's contained in this manual. You can also contact a special ustomer Support number for initial help in getting your module up and running: United States Outside United States.0.. Monday riday, am pm ST Please contact your local Rockwell utomation representative for any technical support issues. New Product Satisfaction Return Rockwell tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. owever, if your product is not functioning and needs to be returned: United States Outside United States your distributor. You must provide a ustomer Support case number (see phone number above to obtain one) to your distributor in order to complete the return process. Please contact your local Rockwell utomation representative for return procedure. llen-radley, Rockwell utomation, and Techonnect are trademarks of Rockwell utomation, nc. Trademarks not belonging to Rockwell utomation are the property of their respective companies. Publication -N0-N-P - May 00 PN Supersedes Publication -. - May - opyright 00 Rockwell utomation, nc. ll rights reserved. Printed in the U.S..