PUR (A, B, C, D) INSTRUCTION FOR CONSTANT SPEED WITH WIRING DIAGRAM ROTOR SIZE

Size: px

Start display at page:

Download "PUR (A, B, C, D) INSTRUCTION FOR CONSTANT SPEED WITH WIRING DIAGRAM ROTOR SIZE"

Ethel McCarthy
5 years ago
Views:

1 UR (A, B, C, D) ISTRUCTIO FOR COSTAT SEED WITH WIRIG DIAGRA ROTOR SIZE

2 2 Instruction - Constant Speed drive COSTAT SEED DESCRITIO, COTROL UR (A, B, C, D) ROTOR SIZE DRIVE EQUIET FOR COSTAT SEED Heat recovery is regulated by means of two-position motor operation (on/off control). The electric motor with drive pulley and drive belt are included in the supply. Rotor size Electric motor (50/60 Hz) 1x( V) 3X400 V 3x230V W 0,25 A 25 W 0,12 A 25 W 0,26 A W 0,35 A 40 W 0,16 A 40 W 0,33 A W 0,6 A 180 W 1,1 A COTROL EXALE The performance of the motor alone can be checked by lifting the drive belt off the drive pulley. Always check the direction of rotation. The rotor shall rotate in such a direction that a point on the rotor surface in the extract air will move towards the purging sector. GT2 Room Rum Room Rum GT1 GT1 GT Q1 S1 Q1 S1 Fig. 1:1 Heat recovery Fig. 1:2 Cooling energy recovery Designations GT1, GT2 = Temperature sensor GX1 = Timeswitch = Drive motor GT = Differential thermostat Q1 = ain switch in the electrical equipment cubicle S1 = Control switch = Contactor = Safety isolating switch Room Rum Supplied with the thermal wheel. All other items shown outside the dotted line are required to be field supplied and wired. Fig. 1:3 urging operation S1 S1 S1 GX1

3 Instruction - Constant Speed drive 3 COSTAT SEED WIRIG DIAGRA UR (A, B, C, D) ROTOR SIZE Q1 400/230 V 50 Hz L1 L L3 E L1 L2 L3 E F1 : UVW F2 230 V K:FF GTΔ GT1 1 2 GX1 a GX1 b 0 Aut GX an S1 : :k A1 A L 1~ E Alt UVW E 3 ~ GX1 a b -H1 1 2 Fig. 2. Basic Wiring Diagram Designations F1 Fuses F2 Control circuit fuse GT1 Thermostat GT Differential thermostat GX1 Time switch, a = intermittent operation b = purging operation H1 Signal lamp K:FF Interlocks e.g. extract air fan Contactor VVX :1 Overcurrent protection :k Interlocking contact in. Used in systems with rotation monitor otor Q1 ain switch in the electric equipment cubicle S1 Control switch Safety isolating switch Supplied with the thermal wheel. All other items shown outside the dotted line are required to be field supplied and wired.

4 4 Instruction - Constant Speed drive COSTAT SEED ELECTRICAL COECTIOS UR (A, B, C, D) ROTOR SIZE Extract air Supply air Supply air Extract air WIRE THE ELECTRICAL COECTIOS TO THE ARORIATE OTOR TERIALS UR (A,B,C,D) rotor size anasonic ote! These motors cannot be operated at other voltages other than the ordered voltage, i.e a 240V/1 phase motor cannot be connected to 400V/3 phase or visa versa. Each specific voltage requires a different motor type. 3x400 V/ff = 02, 22, 62, 82 3x400V L1 L2 L3 U V W *) TK GR/C 1x230V *) 1x( V)/ff = 03, 23, 63, 83 L GR/C U1 U2 Z2 TK 3x230V 3x230 V/ff = 04, 24 L1 L2 L3 W *) Capacitor (Included in TK motor) GR/C U V For reversed rotation: switch L1 and L2. TK = Thermal contact GR/G = Ground TK = Thermal contact GR/G = Ground U2 For reversed rotation: switch L1 and L2 TK = Thermal contact GR/G = Ground *] otor cable to be field supplied and wired. ot included in the supply from FläktGroup. L Z2 Reversed rotation UR (A,B,C,D) rotor size AB The motor can be wired for any of below voltages. 3 x 400 V 3 x 230 V Y W2 U2 V2 W2 U2 V2 L1(R) L2(S) L3(T) U1 V1 W1 L1(R) L2(S) L3(T) U1 V1 W1

5 Instruction - Constant Speed drive 5 OTES

6 6 Instruction - Constant Speed drive OTES

7 Instruction - Constant Speed drive 7 OTES

8 FG_DC_9321GB_UR(A,B,C,D)_TE_ _R0 Copyright 2018 FläktGroup UR (A, B, C, D) A HISTORY OF IOVATIO AD RELIABILITY With more than a century of accumulated industry experience, FläktGroup is in a unique position to deliver energy efficient components and solutions for integrated performance, reliability and quality. With modern manufacturing technologies, precise deliveries and technical support, FläktGroup is your partner fulfilling and surpassing industry standards and certifications.» Learn more on or contact one of our offices

PUR (A, B, C, D) INSTRUCTION FOR VARIABLE SPEED WITH WIRING DIAGRAM FOR EMX P10 ROTOR SIZE

PUR (A, B, C, D) INSTRUCTION FOR VARIABLE SPEED WITH WIRING DIAGRAM FOR EMX P10 ROTOR SIZE PUR (A, B, C, D) INSTRUCTI FOR VARIABLE SPEED WITH WIRING DIAGRAM FOR EMX P10 ROTOR SIZE 030 089 2 Installation and commissioning VARIABLE SPEED DESCRIPTI, CTROL CTENTS Safety instructions/scrapping...