AG 400 relay - Gold plated, 4 contacts

Transcription

1 - Gold plated, 4 contacts Datasheet Features Instantaneous relay Plug-in design with secure locking feature for maximum ease of maintenance 4 double make / double break C/O contacts (form Z), gold plated on silver Contact life (mechanical) of 00 million cycles -40 C C operating temperature Contacts cross pollution barrier Optional weld no transfer function Benefits Description The AG 400 relay has 4 double make / double break C/O contacts (form Z). The contacts are gold plated on hard silver. This relay is used when dry circuits route to socket are not identified. The plug-in design offers secure locking feature for maximum ease of maintenance (no wires need to be disconnected or other hardware removed for relay inspection or replacement). The resistance to impact and vibration is conform to standards in force for Railway Transported Equipment. Positive mechanical keying of relay to socket is built into relay and socket during manufacture and terminal identifications are clearly marked on identification plate that is permanently attached to the relay. Proven reliable Long life cycle Easy to maintain and replace Low life cycle cost No maintenance Railway compliancy NF F Rolling stock - Instantaneous relays contacts and sockets NF F6-0/02 Fire behaviour - Railway rolling stock The AG 400 relays is pluggable in the following sockets: EA 02 A, EA 02 AF, EA 03 AF, EA 04 A, EA 04 AF, EA 0 AF, EA 2 AF. Application The AG 400 relay is designed for low level signals switching in dry circuit signal information. The relay is equipped with a contact pollution barrier in case of mixed load operation.

2 Functional and connection diagrams Timing diagram Relay pin correspondence Example: BG keying Relay pin correspondence a b c d R P O C B D A S T N E F K J H W V L M G (rear view of relay shown) X U Y Z a b c d N.B.: Transil not needed on VAC coil relays Led (V) option (respect polarity) D D2 D3 D4 Connection diagram B A C B A C B A C B2 A2 C2 B2 A2 C2 B2 A2 C2 B3 A3 C3 B3 A3 C3 B3 A3 C3 B4 D A4 C4 B4 D A4 C4 B4 D A4 C4 D2 D2 D2 D3 D3 D3 D4 D4 D4 VDC Models (no Transil protection) VDC Models (with Transil protection) VAC Models N.B.: Transil not needed on VAC coil relays. 2

3 Coil data - DC versions Keying Unom (VDC) Uoperating (VDC) () Coil resistance tol.: ± 8% at 20 C (2) Valid for closed relay. Pnom (W) Uhold (VDC) Udrop-out (VDC) R coil (Ω) () L/R (ms) (2) AG 24 6 / FL 36 2 / DG / BG / SV 0 7 / EG 2 88/ Coil data - AC versions Keying Unom (VAC) Uoperating (VAC) Pnom (VA) Uhold (VAC) Udrop-out (VAC) R coil (Ω) () L/R (ms) (2) SZ 80/ CG / () Coil resistance tol.: ± 8% at 20 C (2) Valid for closed relay. Contact data - dry circuit application (gold contacts) Contact configuration 4 C/O double break contact Contact design Stationary contacts 2 single contacts (contacts are in series) Movable contacts solid blade Contact resistance < 20 mω at A (carry only) Maximum contact ratings Operating 20 ma maximum at 72 VDC Carry only (no make and break) A maximum at VDC Minimum current ratings 0 ma at 2 VDC Contact material Stationary contacts Gold plated over hard silver Movable contacts Gold over hard silver overlay laminated to copper 3

4 Contact design Change Over double break contacts Change Over double break contacts with Weld No Transfer option Electrical characteristics Dielectric strength Insulation resistance 2000 VAC, min between contacts 2600 VAC, min between contacts, coil and frame > 000 MΩ at 00 VDC Mechanical & environmental characteristics Vibration NF F The tests are conducted in the X, Y, Z planes at frequency between 0 & 0 cycles (sinusoidal) at 2 g Shock NF F Tests are applied in both directions in the X, Y & Z planes. Then successive shocks are administered consisting of the positive component of sinusoidal with a value of 30 g, 8 ms Other vibration and shock tests can be performed on request Mechanical life > 00 x 0 6 operations Weight 300 g Temperature -40 C C Humidity 93% RH, 40 C for 4 days Salt mist % NaCl, 3 C for 4 days Protection IP40 (relay on socket) Fire & smoke Materials: Polycarbonate (cover) / polyester melamine (base) Note: These materials have been tested for fire propagation and smoke emission according standards NF F 6-0, NF F

5 Dimensions (mm) Used with locking brackets Used with wire locking spring

6 Dynamic relay selection curve No AC Current breaking capacity versus life expectancy in millions of cycles. Rate of contacts opening and closing = 200 operations per hour. Curves shown for resistive load (Power Factor = ). Curve VAC Millions of Cycles 2, 2 0, 0,2 0, 0, 2 2, Amps (for specific power contacts on customer circuitry only, not interchangeable into another socket with different customer circuitry configuration) 6

7 Dynamic relay selection curve No 2 DC Current breaking capacity versus life expectancy in millions of cycles. Rate of contacts opening and closing = 200 operations per hour. Curves shown for inductive load: L/R= 20 ms continuous current L/R= 40 ms continuous current * By connecting 2 contacts in series, DC current breaking capacity increases by 0 % Curves VDC Millions of Cycles , 0 0,2 0,2 0, Amps (for specific power contacts on customer circuitry only, not interchangeable into another socket with different customer circuitry configuration) 7

8 Dynamic relay selection curve No 3 DC Current breaking capacity versus life expectancy in millions of cycles. Rate of contacts opening and closing = 200 operations per hour. Curves shown for resistive load (L/R = 0). Continuous current. * By connecting 2 contacts in series, DC current breaking capacity increases by 0 % Curve VDC Millions of Cycles , 0 0,2 0,2 0, Amps (for specific power contacts on customer circuitry only, not interchangeable into another socket with different customer circuitry configuration) 8

9 Dynamic relay selection curve No 4 Maximum contact breaking capacity versus voltage for a given L/R. Rate of contacts opening and closing = 600 operations per hour. Curves shown for resistive load (L/R=0) and inductive loads. Continuous current. Life expectancy: 2 Millions of Cycles Curve L/R= 0ms ms 20ms 40ms 60ms 00ms Volts Amps (for specific power contacts on customer circuitry only, not interchangeable into another socket with different customer circuitry configuration) 9

10 Dynamic relay selection curve No Maximum power interruption versus load time constant (L/R) for a given voltage. Curves shown for resistive loads. I = P/V. Curve VDC L R ms A 0 2 2A A Watts (for specific power contacts on customer circuitry only, not interchangeable into another socket with different customer circuitry configuration) 0

11 Dynamic relay selection curve No 6 AC Current breaking capacity versus life expectancy in millions of cycles. Rate of contacts opening and closing = 200 operations per hour. Values shown for inductive loads - Cos Ø = 0.7 Cos Ø = 0. Curves,3 &4 2, &7 6,9 &0 8, &2 Cos Ø = 0.3 VAC Millions of Cycles 2, , 0,2 0, 0, 2 2, Amps (for specific power contacts on customer circuitry only, not interchangeable into another socket with different customer circuitry configuration)

12 Mounting possiblities / sockets EA 02 A EA 03 AF EA 04 A EA 2 AF Panel/flush mounting EA 02 A EA 02 AF EA 04 A EA 04 AF EA 2 AF Locking bracket (90843), rear connection, double Faston mm Wire locking spring (92683), rear connection, single Faston mm Locking bracket (90843), rear connection, single Faston x 0.8 mm Wire locking spring (92683), rear connection, single Faston x 0.8mm Wire locking spring (92683), rear connection, crimp contact Surface/wall mounting EA 03 AF* EA 0 AF* Wire locking spring (92683), front connection, M3 screw 6. mm ring terminals (2, mm 2 ) Wire locking spring (92683), front connection, single Faston mm * Mounting possibility on 3 mm rail EN 0022 by adding suffix D to the part number (see socket datasheet) Note: Keying of relay to socket can be specified by adding the keying letters in the part number. See all details in the related socket datasheet. 2

13 Spare parts Spare parts - order part numbers () () () () LOCKING BRACKET () () SCREW FOR BRACKET METAL STRAP (2) METAL STRAP (4) C92720 P (2) (3) P92806 WIRE LOCKING SPRING ROUND PLASTIC PLUGS HEX. PLASTIC KEYS LOCK PINS ASSY 2 SCREWS () Parts only for socket (2) Parts for relay and socket (3) Parts only for relay 3

14 Instructions Installation Install socket and connect wiring correctly according identification to terminals. Plug relay into socket. Reverse installation into socket not possible due to mechanical blocking by snap-lock. Don t reverse polarity of coil connection. Relays can be mounted (tightly) next to each other and in any attitude. Warning! Never use silicon spray near by relays Operation Before operating always apply voltage to coil to check correct operation. Long term storage may corrode the silver on the relay pins. Just by plugging the relay into the socket, the female bifurcated receivers will automatically clean the corrosion on the pins and guarantee a good connection. Do not use the relay in places with flammable gas as the arc generated from switching could ignite gasses. Maintenance Correct operation of relay can easily be checked as transparent cover gives good visibility on the moving contacts. When the relay doesn t seem to operate correct, please check presence of coil voltage. Use a multimeter. If LED is used, coil presence should be indicated. If coil voltage is present, but the relay doesn t work, a short circuit of suppression diode is possible (The coil connection was reversed). If relay doesn t work after inspection, please replace relay unit by a similar model. Send defective relay back to manufacturer. Normal wear and tear excluded. 4

15 Ordering scheme Configuration: AG AG S C V F. Relay model 2. Nominal 3. Keying 4. Coil. Weld 6. LED 7. Cover 8. Language voltage OVP no transfer ind. type (test report) This example represents a AG AG S C V F. Description: AG 400 series relay, Unom: 24 VDC, Keying AG, Transil coil protection, Weld no transfer, LED indicator, relay cover for wire locking spring, test report in English. Relay model AG & 3. Nominal voltage and keying AG FKL DG BG US SV EG 24 VDC 36 VDC 48 VDC 72 VDC 96 VDC 0 VDC 2 VDC SZ CG VAC 220 VAC 4. Coil overvoltage protection No coil protection P Avalance diode coil protection S Transil coil protection (only with 400 type). Weld no transfer option Regular double break contacts C Weld no transfer 6. LED indicator No LED V LED voltage indicator 7. Relay cover type Relay cover with lock pins F Relay cover forwire locking spring 8. Language on test report French English 2 Spanish

16 MS Relais SAS AG 400 relay-v.2 Nov 20 Tour Rosny 2, Avenue du Général de Gaulle, F Rosny-sous-Bois Cedex, FRANCE T +33 (0) , F +33 (0) E sales@msrelais.com Mors Smitt Asia Ltd. # 807, Billion Trade Centre, 3 Hung To Road Kwun Tong, Kowloon, HONG KONG SAR T , F E info@morssmitt.hk Nieaf-Smitt B.V. Vrieslantlaan 6, 326 AA Utrecht, NETHERLANDS T +3 (0) , F +3 (0) E sales@nieaf-smitt.nl Mors Smitt Technologies Inc. 420 Sackett Point Road North Haven, CT 06473, USA T + (203) , F + (888) E mstechnologies@msrelais.com Mors Smitt UK Ltd. Doulton Road, Cradley Heath West Midlands, B64 QB, UK T +44 (0) , F +44 (0) E info@morssmitt.co.uk (c) Copyright 20 All rights reserved. Nothing from this edition may be multiplied, or made public in any form or manner, either electronically, mechanically, by photocopying, recording, or in any manner, without prior written consent from Mors Smitt. This also applies to accompanying drawings and diagrams. Due to a policy of continuous development Mors Smitt reserves the right to alter the equipment specification and description outlined in this datasheet without prior notice and no part of this publication shall be deemed to be part of any contract for the equipment unless specifically referred to as an inclusion within such contract.