Nominal operating voltage Maximum operating voltage C High temp test

Transcription

1 ENGINEERING DATA SHEET SERIES 9 CONTACTOR AMP Balanced armature design Hermetically sealed, mechanical interlock Designed to the performance standards of MILPRF6106 PRINCIPLE TECHNICAL CHARACTERISTICS Contacts rated at 28 Vdc; Vac, 400Hz, 1 Ø /200 Vac, 400 Hz, 3Ø Weight Dimensions 29 lb max 6in x 380in x 270in APPLICATION NOTES: F 007 Special units available upon request CONTACT ELECTRICAL CHARACTERISTICS Contact rating per pole and load type [1] 28 Vdc Vac 400 Hz Load current in Amps /200 Vac 400 Hz, 3Ø Vac 60 Hz 440 Vac 60 Hz DELTA Resistive Inductive [4] Motor Intermediate current Load transfer [3] Featuring LEACH power and control solutions wwwesterlinecom AMERICAS 6900 Orangethorpe Ave PO Box 32 Buena Park, CA 906 Tel: (01) Fax: (01) EUROPE 2 Rue Goethe 7430 Sarralbe France Tel: (33) Fax: (33) ASIA Units /F Lakeside 1 No8 Science Park West Avenue Phase Two, Hong Kong Science Park Pak Shek Kok, Tai Po, NT Hong Kong Tel: (82) Fax: (82) Data sheets are for initial product selection and comparison Contact Esterline Power Systems prior to choosing a component Date of issue: 06/10 16 Page 1 of Export Control Regulation : EAR 99 These commodities, technology or software are exported from the United States in accordance with the Export Administration Regulations Diversion contrary to US law is prohibited

2 COIL CHARACTERISTICS (Vdc) SERIES 9 CODE Vdc Vac 60/400 Hz Suppressed Vdc [2] Nominal operating voltage Maximum operating voltage Pickup voltage + C High temp test 100 Continuous current test 104 Dropout voltage, max Coil resistance Ohms ±10% at +2 C Coil current max ma at +2 C 200 GENERAL CHARACTERISTICS Temperature range 70 C to + C Minimum operating cycles (life) at rated load,000 Minimum operating cycles (life) at 2% rated load 100,000 Dielectric strength at sea level Auxiliary contacts DC 1,2 Vrms AC 1,0 Vrms All other points DC 1,2 Vrms AC 1,800 Vrms All circuits to ground and circuit to circuit 1,0 Vrms Coil to ground DC 1,0 Vrms AC 1,2 Vrms Dielectric strength at altitude 80,000 ft Insulation resistance (at 0 Vdc) minimum Sinusoidal vibration (7010 Hz) Shock (69 ms duration) Maximum contact opening time under shock or vibration 700 Vrms 100 M Ω min G G 2 ms Operate time at nominal voltage DC 30 ms max AC 30 ms max Release time at nominal voltage DC 10 ms max AC ms max Contact bounce at nominal voltage 2 ms max [1] Weight, max 290 lb Date of issue: 06/10 Page 2 of

3 RELAY NUMBERING SYSTEM SERIES 9 LEACH PART NO DESCRIPTION MS NUMBER CONFIGURATION SCHEMATIC PDTNO, AMP, DC COIL PDTNO, AMP, DC COIL, SUPPRESSED PDTNO, AMP, DC, AC COIL PDTNO, AMP, AC COIL ZC PDTNO, AMP, DC COIL, AUX PDTNO, AMP, DC COIL, SUPPRESSED, AUX 92ZC7D PDTNO, AMP, AC COIL, AUX PDTNO, AMP, DC, AC COIL, AUX PSTNO, AMP, DC COIL PSTNO, AMP, DC COIL, SUPPRESSED PSTNO, AMP, DC COIL, AUX PSTNO, AMP, DC COIL, SUPPRESSED, AUX PSTNO, AMP, AC COIL PSTNO, AMP, AC COIL, AUX 4 7 Special models available upon request, please contact factory NOTES [1] Auxiliary contact rating: Resistive and inductive: (28 Vdc or Vac) Amp Lamp: (28 Vdc or Vac) 1 Amp Bounce at nominal voltage maximum: 004 sec max [2] Suppressed coils have back EMF suppression to 42 Vdc [3] Suitable for transfer between unsynchronized AC power at ratings indicated [4] Inductive load life is 20 percent of rated resistive load life Date of issue: 06/10 18 Page 3 of

4 CONFIGURATION SERIES 9 FIGURE 1 FIGURE MIN 1832 ±010 8 DIA MIN 1832 ±010 8 DIA ± ± MIN 297 MIN ± ±062 STUD, #1032 UNA NUT, MS3630T LOCKWASHER, MS FLATWASHER, AN960T, QTY 2 STUD, #632 UNC2A NUT, MS364926T LOCKWASHER, MS WASHER, AN9616T, QTY 2 4 PLACES STUD, #1032 UNA NUT, MS3630T LOCKWASHER, MS FLATWASHER, AN960T, QTY 2 STUD, #632 UNC2A NUT, MS364926T LOCKWASHER, MS WASHER, AN9616T, QTY WEIGHT () ZC ZC7D3001 WEIGHT () FIGURE FIGURE MIN 1832 ±010 8 DIA MIN 1832 ±010 8 DIA ± ± MIN MIN 4649± ±062 STUD, #1032 UNA NUT, MS3630T LOCKWASHER, MS FLATWASHER, AN960T, QTY 2 STUD, #632 UNC2A NUT, MS364926T LOCKWASHER, MS WASHER, AN9616T, QTY 2 2 PLACES STUD, #1032 UNA NUT, MS3630T LOCKWASHER, MS FLATWASHER, AN960T, QTY 2 STUD, #632 UNC2A NUT, MS364926T LOCKWASHER, MS WASHER, AN9616T, QTY 2 10 PLACES WEIGHT () WEIGHT () STANDARD TOLERANCE: ± 031 Date of issue: 06/10 Page 4 of

5 TERMINAL BARRIERS (OPTIONAL) SERIES 9 SCHEMATIC DIAGRAM #3 SCHEMATIC DIAGRAM #1 SCHEMATIC DIAGRAM #2 AUXILIARY SCHEMATIC DIAGRAM #4 SCHEMATIC DIAGRAM # SCHEMATIC DIAGRAM #6 AUXILIARY SCHEMATIC DIAGRAM #7 SCHEMATIC DIAGRAM #8 AUXILIARY AUXILIARY TERMINAL BARRIER (OPTIONAL) PART NUMBER: ±00 DIA 42 ±007 7 ± ± DIA C'BORE FARSIDE MATERIALS: DIALL FS80 (BLACK) 2 FOUR EACH REQUIRED Date of issue: 06/10 Page of