- PDF Free Download

Size: px

Start display at page:

Download ""

Camilla Hoover
6 years ago
Views:

10 Manufacturing quality. Delivering service. Single Conductors DESCRIPTION: Single copper conductor, tinned stranded insulated with moisture and heat resistant, chemically cross-linked polyethylene insulation (VW-1). Temperature rating 90C in wet and dry location. Switchboard Wire UL Type SIS 600 Volt Copper STANDARDS: UL 44 C(UL) US: CSA/UL Listed Flame Rated: UL 1581 Vertical Flame (VW1) (#14 and larger) ROHS Compliant Dual Rated Type XHHW-2 (#14 & larger) (UL 66 Fixture Wire for #16 AWG) Per ICEA S / NEMA WC-70 Gasoline and Oil Resistant II Sunlight Resistant Excellent crush and abrasion resistance -40 C rated Federal Spec AA Flex-Strand Catalog Number Size AWG or KCMIL Flex-Strand Stock Stranding Class B Stock Class C Stock Insulation Thickness (mils) Nominal Diameter Overall (inch) Approx. Net Wt. per 1000 ft. (lbs.) Ampacity* (30ºC Ambient) 90ºCWet/Dry SIS16KT 16 *** SIS14KTVW ** SIS12KTVW ** SIS10KTVW ** SIS8HTVW SIS6HTVW COLOR CHART Size Blue Black Brown Green Gray Orange Red White Yellow 16 X X 14 X X X X X X X X 12 X X X X X X X 10 X 8 X 6 X *Per NEC Table ** The overcurrent protection for items marked ** shall not exceed 15 amps for 14 AWG, 20 amps for 12 AWG, and 30 amps for 10 AWG per NEC footnote. ***#16 AWG is not recognized as Type SIS or XHHW-2. This conductor will carry one or more of the following listings: FFH-2, RFH-2, RFFH-2, RFHH-3 NOTE: Copper Conductor available Non-Tinned. NOTE: The data shown is approximate and subject to standard industry tolerances Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

15 Manufacturing quality. Delivering service. Available with tinned conductors. Description: Single conductor, stranded copper, insulated with heat and moisture resistant, cross-linked polyethylene insulation, (Type XHHW- 2), with an overall flame and sunlight resistant, Zero Halogen, Limited Smoke, Zero Lead jacket. EnviroPlusTM Power Cable 600 Volt Single Conductor Power Cable XHHW-2 Zero Halogen, Limited Smoke Jacket Standards: LS and CT Rated 1/0 and larger per UL1685 Conductors UL44 ICEA S /NEMA WC-70 IEEE ,000 BTU flame test 1/0 and larger Federal spec A-A UL Listed construction Temperature Rating: 90 C Wet/Dry Sunlight resistant; superior water resistance Excellent crush and abrasion resistance Zero Halogen, Limited Smoke Jacket, -40 C Single Conductors Size AWG or MCM Strand (no.) Insulation Thickness (mils) Jacket Thickness (mils) Nominal Diameter Overall (inch) Approx. Net Weight per 1000 feet (lbs.) Ampacity* 30 C Ambient 90 C Wet/Dry / / / / *Per NEC-Table The overcurrent protection for items marked with an obelisk ( ) shall not exceed 15 amps for 14 AWG, 20 amps for 12 AWG and 30 amps for 10 NOTE: The data shown is approximate and subject to standard industry tolerances Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

16 Manufacturing quality. Delivering service. Single Conductors Description: Single conductor insulated with heat and moisture resistant, cross-linked polyethylene insulation, (Type USE-2), with an overall flame and sunlight resistant, Zero Halogen, Limited Smoke, Zero Lead jacket. Tinned conductors available. EnviroPlusTM Photovoltaic Cable 1000 Volt Single Conductor Power Cable USE-2 or RHH or RHW-2 Zero Halogen, Limited Smoke Jacket Standards: UL Listed as Type PV Cable Conductors UL854 (#16 per UL 66) ICEA S /NEMA WC-70 Flame Rated: VW-1 per UL 1685 Temperature Rating: 90 C Wet/Dry Sunlight resistant; superior water resistance Excellent crush and abrasion resistance -40º C Cold Bend and Cold Impact Zero Halogen, Limited Smoke Jacket Size AWG or MCM Strand (no.) Insulation Thickness (mils) Jacket Thickness (mils) Nominal Diameter Overall (inch) Approx. Net Weight per 1000 feet (lbs.) Ampacity* 30 C Ambient 90 C Wet/Dry *Per NEC-Table The overcurrent protection for items marked with an obelisk ( ) shall not exceed 15 amps for 14 AWG, 20 amps for 12 AWG and 30 amps for 10. NOTE: The data shown is approximate and subject to standard industry tolerances Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

38 Manufacturing quality. Delivering service. ServiceDrive ASD/VFD Shielded Tray Drive Cable PVC Jacket Overall Patent Pending Description: 3 conductors, stranded, insulated with heat and moisture resistant cross-linked polyethylene, phase identified, cabled together with suitable fillers and 3 bare copper ground conductors. Cable core covered with 5-mil helical copper tape shield, and overall flame and sunlight resistant black PVC jacket. Surface printed. Jacket available in colors. Features: Suitable for use in NEC Hazardous Locations: Class I - Div 2, Class II - Div 2, and Class III, Div 1 and 2 May be used in ASD / VFD applications Standards: UL 1277 Flame Rated: IEEE 383 (70,000 BTU), ICEA T (210,000 BTU) on 1/0 and larger IEEE 1202 / CSA FT-4 Two-hour Firewall rated, (2/0 AWG and smaller) Sunlight Resistant, for CT Use; Direct Burial Oil Resistant II Jacket Code: Black and Numbered Temperature Rating: 90C Wet / Dry ICEA S / NEMA WC-70 Size AWG or MCM Strand (no.) Insulation Thickness (mils) Copper Grounding Conductor(s) (AWG) PVC Jacket Thickness (mils) Approx. Diameter Overall (inch) Approx. Net Wt. per 1000 ft. (lbs.) Ampacity* (30 C Ambient Wet/Dry) THREE CONDUCTOR # # # # # # # # , # , / # , / # , / # , / # , # , # , # , / , / , *Per NEC Table **Fillers used when required. + The overcurrent protection for items marked with an obelisk (+) shall not exceed 15 amps for 14 AWG, 20 amps for 12 AWG, and 30 amps for 10 AWG per NEC footnote. Note: The data shown is approximate and subject to standard industry tolerances. August 2007 Made in the USA Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

39 Manufacturing quality. Delivering service. ServiceDrive Plus ASD/VFD Shielded Tray Drive Cable Factory Mutual Group 1 Listed, Zero Halogen, Limited Smoke, Lead Free, Patent Pending Description: 3 conductors, stranded, insulated with heat and moisture resistant cross-linked polyethylene, phase identified, cabled together with suitable fillers and 3 bare copper ground conductors. Cable core covered with 5-mil helical copper tape shield, and overall flame and sunlight resistant black zero-halogen, limited smoke, zero lead jacket. Features: Suitable for use in NEC Hazardous Locations: Class I - Div 2, Class II - Div 2, and Class III, Div 1 and 2 May be used in ASD / VFD applications Standards: UL 1277 Flame Rated: IEEE 383 (70,000 BTU), IEEE 1202 / CSA FT-4, UL 1685 LS Factory Mutual Group 1 Listed Two-hour Firewall rated, (2/0 AWG and smaller) Sunlight Resistant, for CT Use; Direct Burial Color Code: Black and Numbered Temperature Rating: 90C Wet / Dry ICEA S / NEMA WC-70 Zero Halogen, Limited Smoke, -40C Open wiring (Exposed Runs) 4 AWG and larger Size AWG or MCM Strand (no.) Insulation Thickness (mils) Copper Grounding Conductor(s) (AWG) PVC Jacket Thickness (mils) Approx. Diameter Overall (inch) Approx. Net Wt. per 1000 ft. (lbs.) Ampacity* (30 C Ambient Wet/Dry) THREE CONDUCTOR # # # # # # # # , # , / # , / # , / # , / # , # , # , # , / , / , *Per NEC Table **Fillers used when required. ***Cables marked for open wiring / exposed runs must contain a ground wire + The overcurrent protection for items marked with an obelisk (+) shall not exceed 15 amps for 14 AWG, 20 amps for 12 AWG, and 30 amps for 10 AWG per NEC footnote. Note: The data shown is approximate and subject to standard industry tolerances. August 2007 Made in the USA Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

42 Manufacturing quality. Delivering service. Description: 3 or 4 conductors, stranded, insulated with heat & moisture resistant cross-linked polyethylene (type XHHW-2), phase identified, cabled together with suitable fillers** & green or bare ground conductor. Cable core covered with binder tape, aluminum or galvanized steel interlocked armor. Jacket upon request. Standards: UL 1569, ICEA S /NEMA WC-70 NEC Article 330 Cable Tray Rated 600 Volt, 90 C rated dry locations (Wet/Dry with Jacket) Color coding: Black and Numbered with a Green Ground 1/0 AWG and larger: Black and Numbered with a Bare Ground Size AWG or MCM Strand (no.) Insulation Thickness (mils) Insulated Copper Grounding Conductor(s) (AWG) (Green) Feeder Size MC Cable 600V / UL Type MC Galvanized Steel or Aluminum Copper XHHW-2 Applications Service Wire s Feeder Size MC cable is designed to be a cost effective replacement for conduit & wire. Suitable for service, branch & feeder circuits. Ideal for use in commercial, industrial & utility applications. This flexible cable assembly offers: labor/time savings, an increased resistance to mechanical damage, system design flexibility & the reliability of a factory assembled & tested cable system. Features Suitable for use in NEC hazardous locations: Class I, Div. 2 Class II, Div. 2 Two-hour Firewall rated, (2/0 AWG and smaller) For use in Theatres (Article 520), Motion Picture & TV Studios (Article 530) & Places of Assembly with more than 100 people Can be messenger supported (Article 330) Diameter over Armor (inch) Approx. Net Wt. per 1000 ft. (lbs.) Alum. Armor Galv. Armor Ampacity* (30 C Ambient Wet/Dry) 90 C Armor Cables TWO FOUR CONDUCTOR THREE CONDUCTOR / *** / *** / *** / *** *** *** *** *** *** *** *** / *** / *** / *** / *** *** *** *** *** *** *** *** ,250 11, *Per NEC Table **Fillers used when required. *** Bare Copper Grounds. NOTE: The data shown is approximate and subject to standard industry tolerances. NOTE: 4-Conductor ampacity assumes all four conductors are hot. If three are hot and one is a neutral, use the three conductor ampacity Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

44 Manufacturing quality. Delivering service. Description: 3 or 4 conductors, stranded, insulated with heat and moisture resistant cross-linked polyethylene (type XHHW-2), phase identified, cabled together with suitable fillers** and bare copper ground conductor(s). Cable core covered with binder tape, aluminum or galvanized steel interlocked armor, with flame and sunlight resistant black PVC jacket. Jacket available under armor and in other colors. Features: Suitable for use in NEC Hazardous locations: Class I, Div. 2 Class II, Div. 2 THREE CONDUCTOR Size AWG or MCM Strand (no.) Insulation Thickness (mils) Copper Grounding Conductor(s) (AWG) Diameter over Armor (inch) Interlocked Armor 600 Volt UL Type MC Galvanized Steel or Aluminum Copper XHHW-2 Standards: UL 1569 Flame Rated: IEEE-383 (70,000 BTU), ICEA T (210,000 BTU), IEEE 1202/CSA FT-4 Two-hour Firewall rated, (2/0 AWG and smaller) Sunlight Resistant for CT Use; Direct Burial 1, Oil Resistant II Jacket Color Code Black and Numbered / other color codes available Temperature rating at 90 C Wet/Dry ICEA S /NEMA WC-70 PVC Jacket Thickness (mils) Approx. Diameter Overall (inch) Approx. Net Wt. per 1000 ft. (lbs.) Alum. Armor Galv. Armor Ampacity* (30 C Ambient Wet/Dry) # # # # # # / # / # / # / # # # # # # # # C Armor Cables FOUR CONDUCTOR # # # # # # / # / # / # / # # # # # # # # *Per NEC Table Includes encasement in concrete. **Fillers used when required. NOTE: The data shown is approximate and subject to standard industry tolerances. NOTE: 4-Conductor ampacity assumes all four conductors are hot. If three are hot and one is a neutral, use the three conductor ampacity Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

48 Manufacturing quality. Delivering service. ServiceDrive ASD/VFD Shielded Interlocked Armor Drive Cable PVC Jacket Overall Patent Pending Description: 3 conductors, stranded, insulated with heat and moisture resistant cross-linked polyethylene, phase identified, cabled together with suitable fillers** and 3 bare copper ground conductors. Cable core covered with binder tape, 5-mil helical copper tape shield, galvanized steel interlocked armor, with flame and sunlight resistant PVC jacket overall. Jacket available in colors. Features: Suitable for use in NEC Hazardous Locations: Class I - Div 2, Class II - Div 2, and Class III, Div 1 and 2 Suitable for ASD / VFD applications Standards: UL 1569 Flame Rated: IEEE 383 (70,000 BTU), ICEA T (210,000 BTU), IEEE 1202 / CSA FT-4 Two-hour Firewall rated, (2/0 AWG and smaller) Sunlight Resistant, for CT Use; Direct Burial 1 Oil Resistant II Jacket Color Code: Black and Numbered Temperature Rating: 90C Wet / Dry ICEA S / NEMA WC-70 THREE CONDUCTOR Size AWG or MCM Strand (no.) Insulation Thickness (mils) Copper Grounding Conductor(s) (AWG) Diameter over Armor (inch) PVC Jacket Thickness (mils) Approx. Diameter Overall (inch) Approx. Net Wt. per 1000 ft. (lbs.) (Galvanized) Ampacity* (30 C Ambient Wet/Dry) # # # # # # # # # / # / # / # / # # # # / / C *Per NEC Table Includes encasement in concrete. + The overcurrent protection for items marked with an obelisk (+) shall not exceed 15 amps for 14 AWG, 20 amps for 12 AWG, and 30 amps for 10 AWG per NEC footnote. Note: For VFD / ASD applications, galvanized armor should be preferred (for magnetic noise reduction). Note: The data shown is approximate and subject to standard industry tolerances Made in the USA Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

49 Manufacturing quality. Delivering service. ServiceDrive Plus ASD/VFD Shielded Interlocked Armor Drive Cable Factory Mutual Group 1 Listed, Zero Halogen, Limited Smoke, Lead Free Patent Pending Description: 3 conductors, stranded, insulated with heat and moisture resistant cross-linked polyethylene, phase identified, cabled together with suitable fillers and 3 bare copper ground conductors. Cable core covered with binder tape, 5-mil helical copper tape shield, aluminum or galvanized steel interlocked armor, with flame and sunlight resistant zero halogen, limited smoke, zero lead jacket overall. Features: Suitable for use in NEC Hazardous Locations: Class I - Div 2, Class II - Div 2, and Class III, Div 1 and 2 Designed exclusively for ASD / VFD applications. Standards: UL 1569 Flame Rated: IEEE 383 (70,000 BTU), IEEE 1202 / CSA FT-4, UL 1685 LS Factory Mutual Group 1 listed Two-hour Firewall rated, (2/0 AWG and smaller) Sunlight Resistant, for CT Use; Direct Burial 1 Color Code: Black and Numbered Temperature Rating: 90C Wet / Dry ICEA S / NEMA WC-70 Zero Halogen, Limited Smoke Jacket, -40C THREE CONDUCTOR Size AWG or MCM Strand (no.) Insulation Thickness (mils) Copper Grounding Conductor(s) (AWG) Diameter over Armor (inch) PVC Jacket Thickness (mils) Approx. Diameter Overall (inch) Approx. Net Wt. per 1000 ft. (lbs.) Ampacity* (30 C Ambient Wet/Dry) 90 C # # # # # # # # # / # / # / # / # # # # / / *Per NEC Table Includes encasement in concrete. + The overcurrent protection for items marked with an obelisk (+) shall not exceed 15 amps for 14 AWG, 20 amps for 12 AWG, and 30 amps for 10 AWG per NEC footnote. Note: For VFD / ASD applications, galvanized armor should be preferred (for magnetic noise reduction). Note: The data shown is approximate and subject to standard industry tolerances 2007 Made in the USA Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

62 Manufacturing quality. Delivering service. Submersible Pump Cable TYPE THW-Heavy Duty FLAT BLACK JACKETED with Ground 75 C/600V Description & Features: UL listed Type THW heavy duty flat submersible pump cable is a multi-purpose cable with parallel, individually insulated, color coded conductors and an overall jacket. Construction provides flexible copper stranding insulated with Type THW (PVC) compound. A tough PVC jacket, with a non-penetrating web, is easily stripped to facilitate installation yet provide optimum flexibility, mechanical protection and crush resistance. UL listed as Type THW Submersible Pump Cable Acid, alkali, oil and grease resistant Weather, ozone and sunlight resistant jacket Abrasion and crush resistant Sequential footage marks Applications: For use within the well casing to supply power to the submersible pump Designed for use where extra mechanical protection and flexibility during installation and operation are required Construction: Conductors: Flexible stranded soft annealed copper Insulation: Thermoplastic polyvinyl chloride (PVC) Color coding: black, red, yellow, green (ground) Assembly: The insulated conductors, including the grounding conductor, are configured flat and parallel without fillers Jacket: Black thermoplastic polyvinyl chloride (PVC) applied directly over the conductors with a non-penetrating web Temperature: 75 C Voltage: 600 Volts Specifications & Standards: UL Standard 83 TWO OR THREE CONDUCTORS WITH GREEN INSULATED GROUNDING CONDUCTORS Conductor Size, AWG Dimensions (Inches) Standard Ampacity Weight Item Code Power Ground Insulation Jacket O.D. Packaging NEC (Lbs./Mft.) PMP12/2GGHD 12/2 (19 str) 12 (19 str) x & PMP10/2GGHD 10/2 (19 str) 10 (19 str) x & PMP14/3GGHD 14/3 (7 str) 14 (7 str) x & PMP12/3GGHD 12/3 (19 str) 12 (19 str) x & PMP10/3GGHD 10/3 (19 str) 10 (19 str) x & PMP8/3GGHD 8/3 (19 str) 10 (19 str) x & PMP6/3GGHD 6/3 (19 str) 8 (19 str) x & PMP4/3GGHD 4/3 (19 str) 8 (19 str) x & PMP2/3GGHD 2/3 (19 str) 6 (19 str) x & PMP1/03GGHD 1/03 (19 str) 6 (7 str) x Bulk PMP2/03GGHD 2/03 (19 str) 6 (7 str) x Bulk PMP3/03GGHD 3/03 (19 str) 4 (7 str) x Bulk PMP4/03GGHD 4/03 (19 str) 4 (7 str) x Bulk PMP250/3GGHD 250/3 (37 str) 4 (7 str) x Bulk PMP350/3GGHD 350/3 (37 str) 3 (7 str) x Bulk Pump and Irrigation Per Table of the NEC All values are nominal; all weights are exclusive of packaging. All diameters and weights are subject to normal manufacturing tolerances. * Direct Burial rated in sizes 12 through 4/0 AWG, upon request All sales are subject to Standard Terms & Conditions of Sale Phoenix, AZ Culloden, WV Houston, TX Pittsburgh, PA

TC-XHHW-2 Copper, XLPE Insulated, PVC Jacketed

TC-XHHW-2 Copper, XLPE Insulated, PVC Jacketed ER, FT4, RoHS, Dir Bur; Singles: VW-1; GR I & II; SR; RW90; RoHS; 600 V Features UL Listed as TC-ER - exposed run tray cable. Jacket is rated Sunlight Resistance,