UNSHIELDED MULTI CONDUCTOR

Size: px

Start display at page:

Download "UNSHIELDED MULTI CONDUCTOR"

Julie Powers
6 years ago
Views:

1 PLTC 300 VOLT PVC Insulation 105 C, 300 Volts UNSHIELDED MULTI CONDUCTOR For use as instrumentation cable inside or outside in control applications. Suitable for installation in trays, troughs, channels, conduit, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Stranded, tinned copper. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. OVERALL JACKET: Sunlight resistant polyvinyl chloride (PVC). 4. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable passes CSA FT 4 and UL 1581 vertical tray flame tests. 5. TEMPERATURE: 105 C 6. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Conductors IN 1000 Ft B B B B B B B B B B B Color Code for two conductor: Black and Red. Color Code for three conductor: Black, Red and White. Anixter Inc

2 PLTC 300 VOLT PVC Insulation 105 C, 300 Volts SHIELDED MULTI CONDUCTOR For use as instrumentation cable inside or outside in control applications. Suitable for installation in trays, troughs, channels, conduit, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Stranded, tinned copper. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. ASSEMBLY: Cabled with an overall aluminum mylar shield and stranded tinned copper drain wire. 4. OVERALL JACKET: Sunlight resistant polyvinyl chloride (PVC). 5. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable passes CSA FT4 and UL 1581 vertical tray flame tests. 6. TEMPERATURE: 105 C 7. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Conductors IN 1000 Ft B B B B B B B B B B B Color Code for two conductor: Black and Red. Color Code for three conductor: Black, Red and White Anixter Inc. 1999

3 PLTC 300 VOLT PVC Insulation 105 C, 300 Volts OVERALL SHIELDED SINGLE AND MULTI PAIR For use as instrumentation cable inside or outside in control applications. Suitable for installation in trays, troughs, channels, conduit, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Stranded, bare copper. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. PAIRS: Pairs are twisted with a suitable lay to reduce magnetic interference and color coded black and white. Each pair is printed numerically to ensure easy identification. 4. ASSEMBLY: The individual pairs are cabled together to form round completed assembly. Overall aluminum/polyester foil shield with stranded tinned copper drain wire. All cable assemblies include a communication wire for calibration. 5. OVERALL JACKET: Flame retardant, sunlight resistant, black PVC. A rip cord is included for jacket removal. 6. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable meets IEEE 383 and UL 1581 vertical tray flame tests. 7. TEMPERATURE: 105 C 8. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Pairs IN 1000 Ft NOTE: Other pair counts available upon request. Diameters and weights may vary between manufacturers. Anixter Inc

4 PLTC 300 VOLT Continued OVERALL SHIELDED SINGLE AND MULTI PAIR PVC Insulation 105 C, 300 Volts Conductor Size Anixter of Weight Lbs. AWG Pairs IN 1000 Ft NOTE: Other pair counts available upon request. Diameters and weights may vary between manufacturers Anixter Inc. 1999

5 PLTC 300 VOLT PVC Insulation 105 C, 300 Volts INDIVIDUALLY SHIELDED MULTI PAIR For use as instrumentation cable inside or outside in control applications. Suitable for installation in trays, troughs, channels, conduits, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Stranded, tinned copper. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. COLOR CODE: Pairs color coded black, red and numbered. 4. ASSEMBLY: Twisted pairs each with an overall aluminum mylar shield and stranded tinned copper drain wire. 5. OVERALL JACKET: Sunlight resistant chrome polyvinyl chloride (PVC) jacket. 6. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable passes CSA FT4 and UL 1581 vertical tray flame tests. 7. TEMPERATURE: 105 C 8. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Pairs IN 1000 Ft B B B B B B B B B B B B B B B NOTE: Other pair counts available upon request. Anixter Inc

6 PLTC 300 VOLT PVC Insulation 105 C, 300 Volts BELDEN OVERALL SHIELDED MULTI PAIR For use as instrumentation cable inside or outside in control applications. Suitable for installation in trays, troughs, channels, conduit, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Stranded, tinned copper. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. COLOR CODE: Pairs color coded black, red and numbered. 4. ASSEMBLY: Pairs are cabled with an overall aluminum/polyester shield and stranded tinned copper drain wire. 5. OVERALL JACKET: Sunlight resistant polyvinyl chloride (PVC). 6. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable passes CSA FT4 and UL 1581 vertical tray flame tests. 7. TEMPERATURE: 105 C 8. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Pairs IN 1000 Ft B B B B B B B B B B B B B B B B B NOTE: Other pair counts available upon request Anixter Inc. 1999

7 PVC Insulation 105 C, 300 Volts PLTC 300 VOLT INDIVIDUAL AND OVERALL SHIELDED MULTI PAIR For use as instrumentation cable inside or outside in control applications. Individually and overall shielded for greater isolation and noise reduction. Suitable for installation in trays, troughs, conduit, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Bare copper, Class B, concentric stranded. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. PAIRS: Each pair is twisted with a suitable lay to reduce magnetic interference and color coded black and white. Each pair is also printed numerically to ensure easy identification. An aluminum/polyester foil shield with stranded tinned copper drain wire is applied. 4. ASSEMBLY: The individual pairs are cabled together to form a substantially circular cross-section of the completed assembly. An aluminum/polyester foil shield with stranded tinned copper drain wire is applied overall. All cable assemblies include a communication wire for calibration and a rip cord for jacket removal. 5. OVERALL JACKET: Flame retardant, sunlight resistant, black polyvinyl chloride (PVC) jacket. 6. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable meets IEEE 383 and UL 1581 vertical tray flame tests. 7. TEMPERATURE: 105 C 8. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Pairs IN 1000 Ft NOTE: Other pair counts available upon request. Diameters and weights may vary between manufacturers. Anixter Inc

8 Continued PVC Insulation 105 C, 300 Volts PLTC 300 VOLT INDIVIDUAL AND OVERALL SHIELDED MULTI PAIR Conductor Size Anixter of Weight Lbs. AWG Pairs IN 1000 Ft NOTE: Other pair counts available upon request. Diameters and weights may vary between manufacturers Anixter Inc. 1999

9 PLTC 300 VOLT PVC Insulation 105 C, 300 Volts OVERALL SHIELDED SINGLE AND MULTI TRIAD For use as instrumentation cable inside or outside in control applications. Suitable for installation in trays, troughs, channels, conduit, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Bare copper, Class B, concentric stranded. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. TRIADS: Each triad is twisted with a suitable lay to reduce magnetic interference and color coded black, white and red. Each triad is also printed numerically to ensure easy identification. 4. ASSEMBLY: The individual triads are cabled together to form a substantially circular cross-section of the completed assembly. Overall aluminum/polyester foil shield with stranded tinned copper drain wire. All cables include a communication wire for calibration and a rip cord for jacket removal. 5. OVERALL JACKET: Flame retardant, sunlight resistant, black polyvinyl chloride (PVC). 6. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable meets IEEE 383 and UL 1581 vertical tray flame tests. 6. TEMPERATURE: 105 C 7. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Triads IN 1000 Ft NOTE: Other triad counts available upon request. Diameters and weights may vary between manufacturers. Anixter Inc

10 PVC Insulation 105 C, 300 Volts PLTC 300 VOLT INDIVIDUAL AND OVERALL SHIELDED MULTI TRIAD For use as instrumentation cable inside or outside in control applications. Suitable for installation in trays, troughs, channels, conduit, wireways and for aerial use when supported by a messenger. Suitable for Class 2 and 3 electrical circuits per NEC Article CONDUCTORS: Bare copper, Class B, concentric stranded. 2. INSULATION: 105 C polyvinyl chloride (PVC). 3. TRIADS: Each triad is twisted with a suitable lay to reduce magnetic interference and color coded black. Each triad is also printed numerically to ensure easy identification. An aluminum/polyester foil shield with stranded tinned copper drain wire is applied. 4. ASSEMBLY: The individual triads are cabled together to form a substantially circular cross-section of the completed assembly. An aluminum/polyester foil shield with stranded tinned copper drain wire is applied overall. All cable assemblies include a communication wire for calibration and a rip cord for jacket removal. 5. OVERALL JACKET: Flame retardant, sunlight resistant, black polyvinyl chloride (PVC) jacket. 6. STANDARDS: Meets Article 725 of the NEC for Type PLTC and UL 13. Finished cable meets IEEE 383 and UL 1581 vertical tray flame tests. 7. TEMPERATURE: 105 C 8. VOLTAGE: 300 Volts Conductor Size Anixter of Weight Lbs. AWG Triads IN 1000 Ft NOTE: Other triad counts available upon request. Diameters and weights may vary between manufacturers Anixter Inc. 1999

11 PLTC ISA/IEC SP-50 Twisted Pair Orange Jacket 300 Volts BELDEN DATABUS FIELDBUS Bi-directional, digital signal cable used to replace traditional high pair count 4-20ma industrial PLTC cable for fieldbus devices. 1. CONDUCTORS: Tinned, stranded copper. 2. INSULATION: Type A & B Polyethylene (PE). High speed Cellular polyethylene. 3. SHIELD: 100% aluminum/polyester. 4. OVERALL JACKET: Orange polyvinyl chloride (PVC). 5. STANDARDS: Conforms to ISA/IEC SP-50 fieldbus physical layer specification. Meets NEC Article 725 requirements for Type PLTC. Also meets UL and CSA Type CM requirements. Cond. Nominal Belden Size Imped. Capacitance O.D. Anixter Part of Type AWG Stranding Pairs ohms Speed pf/ft. IN B3076F 3076F A 18 7 x kb/s B3077F 3077F B 22 7 x kb/s B3078F 3078F High Speed 22 7 x or 2.5 Mb/s NOTE: European Profibus cable (Belden Part No. 3079F) available upon request. Anixter Inc

12 PLTC Polyolefin Insulation Shielded 600 Volts BELDEN DATATRAY TWINAX For use in most programmable logic control systems (PLCs) and distributed control systems (DCS) in industrial environments. May be installed in cable tray or conduit for a variety of data applications (RS-232, 422 & 485). 1. CONDUCTOR: Annealed, tinned copper. 2. INSULATION: Low attenuation, flame-retardant polyolefin. 3. SHIELD: 100% coverage aluminum/polyester and 55% coverage tinned copper braid. 4. OVERALL JACKET: Dark blue, sunlight resistant, polyvinyl chloride (PVC). 5. STANDARDS: Meets the UL requirements for Type PLTC cable. Meets the UL 1581 vertical tray 70,000 BTU flame test. Meets NEC Article 725 for Class 2 (CL2) circuits and Article 800 for Communications general purpose (CM). Also meets CSA Type CM requirements. Conductor Nominal Belden Size Impedance Capacitance O.D. Anixter Part of Weight Lbs. AWG Stranding Pairs ohms pf/ft. IN 1000 Ft. B3072F 3072F 18 7 x B3073F 3073F 18 7 x B3074F 3074F 18 7 x B3075F 3075F 18 7 x NOTE: Multi pairs/multi conductors available. Wet location rating and Oil Res II jacket available. Any Datatray cable may be armored upon request Anixter Inc. 1999

13 PLTC Aluminum Armor 300 Volts BELDEN INDUSTRIAL AUTOMATION Used in industrial locations requiring extra mechanical protection and system reliability for high speed electronic signalling. 1. CABLE CORE: Cable design configurations for the following PLC manufacturers: Allen Bradley, Square D: Belden Pt. # Allen Bradley: Belden Pt. # , IBM, Foxboro: Belden Pt. # Modicon: Belden Pt. # , GE Fanuc, DEC: Belden Pt. # DEC, Foxboro, Hewlett Packard: Belden Pt. # IBM: Belden Pt. # Honeywell: Belden Pt. # ARMOR: Aluminum interlocked. 3. OVERALL JACKET: Polyvinyl chloride (PVC). 4. STANDARDS: Meets UL ,000 BTU flame test. Meets CSA FT4 flame test requirements. Low acid gas outer jacket per CSA. Conductor Belden Size Inner Jacket Armor Outer Jacket Anixter Part Weight Lbs. UL and CSA AWG IN IN IN 1000 Ft. Designation BA CM BA CM BA CM A-BA CM A-BA CM A-BA CL BA CL DS-BA CL BA CL A-BA * CM BA CM BA CL A-BA CMG BA CMG BA CL BA CL2 * This product is frequently referred to as Allen Bradley armored Blue Hose. Remove 12 from Belden part number to get core part number (e.g., is armored Belden 9463). NOTE: Galvanized steel interlocked armor available upon request. Anixter Inc

14 PVC-Nylon Insulation 90 C, 600 Volts PVC-NYLON/PVC UNSHIELDED AND SHIELDED MULTI CONDUCTOR For use as instrumentation cable inside or outside in control applications and suitable for direct burial. UL Listed for installation in trays, troughs, channels, conduit and wireways in accordance with Articles 318, 340 and 501 of the NEC. TC 600 VOLT 1. CONDUCTORS: Stranded, tinned copper. 2. INSULATION: 90 C polyvinyl chloride (PVC), nylon overcoat. 3. COLOR CODE: Conductors are color coded black, red. 4. ASSEMBLY: Shielded cables are cabled with an overall aluminum/polyester shield and stranded, tinned copper drain wire. 5. OVERALL JACKET: Sunlight resistant polyvinyl chloride (PVC) jacket, suitable for outdoor use and direct burial. 6. STANDARDS: Meets requirements of UL 1277 and passes the UL 1581 vertical tray flame test. 7. TEMPERATURE: 90 C 8. VOLTAGE: 600 Volts Unshielded Conductor Size Anixter of Weight Lbs. AWG Conductors IN 1000 Ft. B B B B Shielded B B B B Anixter Inc. 1999

15 TC 600 VOLT PVC-Nylon Insulation 90 C, 600 Volts PVC-NYLON/PVC SHIELDED MULTI PAIR For use indoors or outdoors and for installation in trays, troughs, channels, ducts and direct burial. Designed for telemetering, signals, relays and communication. 1. CONDUCTORS: Bare copper, Class B stranded per ASTM B INSULATION: Polyvinyl chloride (PVC) and nylon. Pairs are color coded black and white and numbered. Triads are black, white, red and numbered. 3. SHIELDING: Shields are Aluminum/polyester. Overall drain wire is seven-strand tinned copper. Where applicable, individual drain wires are used, also of seven-strand, tinned copper construction. 4. OVERALL JACKET: Sunlight resistant polyvinyl chloride (PVC). 5. STANDARDS: Meets the requirements of UL 1277 and passes the UL 1581 vertical tray flame test. 6. TEMPERATURE: 90 C 7. VOLTAGE: 600 Volts Conductor Overall Jacket Nominal Anixter* Size of Thickness O.D. Weight Lbs. AWG Pairs Triads IN IN 1000 Ft. 2AS-1801POS AS-1801TOS AS-1802POS AS-1803POS AS-1804POS AS-1806POS AS-1808POS AS-1812POS AS-1816POS AS-1824POS AS-1836POS AS-1802SPOS AS-1803SPOS AS-1804SPOS AS-1806SPOS AS-1808SPOS AS-1812SPOS AS-1816SPOS AS-1824SPOS AS-1836SPOS *POS Pair(s) Overall Shield. TOS Triad(s) Overall Shield. SPOS Shielded Pairs with Overall Shield. NOTE: Diameters and weights may vary between manufacturers. Anixter Inc

16 TC 600 VOLT Continued PVC-NYLON/PVC SHIELDED MULTI PAIR PVC-Nylon Insulation 90 C, 600 Volts Conductor Overall Jacket Nominal Anixter* Size of Thickness O.D. Weight Lbs. AWG Pairs Triads IN IN 1000 Ft. 2AS-1601POS AS-1601TOS AS-1602POS AS-1603POS AS-1604POS AS-1606POS AS-1608POS AS-1612POS AS-1616POS AS-1624POS AS-1636POS AS-1602SPOS AS-1603SPOS AS-1604SPOS AS-1606SPOS AS-1608SPOS AS-1612SPOS AS-1616SPOS AS-1624SPOS AS-1636SPOS AS-1401POS AS-1401TOS *POS Pair(s) Overall Shield. TOS Triad(s) Overall Shield. SPOS Shielded Pairs with Overall Shield. NOTE: Diameters and weights may vary between manufacturers Anixter Inc. 1999

17 TC 600 VOLT XLP Insulation Hypalon Jacket 90 C, 600 Volt XLP/HYPALON SHIELDED MULTI PAIR For use indoors or outdoors and for installation in trays, troughs, channels, ducts and direct burial. Designed for telemetering, signals, relays and communication. 1. CONDUCTORS: Annealed, tinned copper in accordance with ASTM B-3 and B-33. Concentric stranded, Class B per ASTM B INSULATION: Cross-linked polyethylene (XLP), per ICEA S (NEMA WC7). UL rated VW-1 conductors. 3. PAIRS/TRIADS: Each pair/triad is twisted to a 2 in. lay. Color coded: pairs black/white, triads black/white/red with alphanumeric designation (1-ONE). 4. ASSEMBLY: The individually shielded pairs are cabled together with non-hygroscopic and flame retardant fillers as necessary to form a circular cross section of the assembly. A binding tape, when required, shall be applied over cable core. 5. SHIELDING: The entire cable assembly is shielded with polyester backed/aluminum tape and tinned copper drain wire. 6. OVERALL JACKET: Flame retardant Hypalon (CSPE). 7. STANDARDS: Meets the requirements of UL Finished cable passes UL ,000 BTU and ICEA T ,000 BTU flame tests. UL listed as sunlight resistant and rated for direct burial. 8. TEMPERATURE: 90 C 9. VOLTAGE: 600 Volts Conductor Insulation Overall Jacket Nominal Size of Thickness Thickness O.D. Anixter* Weight Lbs. AWG Pairs Triads IN IN IN 1000 Ft. 2RH-1601POS RH-1601TOS RH-1602POS RH-1603POS RH-1604POS RH-1606POS RH-1608POS RH-1612POS RH-1624POS RH-1636POS RH-1602SPOS RH-1603SPOS *POS Pair(s) Overall Shield. TOS Triad(s) Overall Shield. SPOS Shielded Pairs with Overall Shield. NOTE: Diameters and weights may vary between manufacturers. Anixter Inc

18 TC 600 VOLT XLP/HYPALON SHIELDED MULTI PAIR Continued XLP Insulation Hypalon Jacket 90 C, 600 Volt Conductor Insulation Overall Jacket Nominal Size of Thickness Thickness O.D. Anixter* Weight Lbs. AWG Pairs Triads IN IN IN 1000 Ft. 2RH-1604SPOS RH-1606SPOS RH-1608SPOS RH-1612SPOS RH-1624SPOS RH-1636SPOS RH-1401POS RH-1401TOS *POS Pair(s) Overall Shield. TOS Triad(s) Overall Shield. SPOS Shielded Pairs with Overall Shield. NOTE: Diameters and weights may vary between manufacturers Anixter Inc. 1999

19 TC 600 VOLT EPR Insulation CPE Jacket 90 C, 600 Volt EPR/CPE SHIELDED MULTI PAIR For use indoors or outdoors and for installation in trays, troughs, channels, ducts and direct burial. Designed for telemetering, signals, relays and communication. 1. CONDUCTORS: Annealed, tinned copper in accordance with ASTM B-3 and B-33. Concentric stranded, Class B per ASTM B INSULATION: Ethylene propylene rubber (EPR), per ICEA S UL rated VW-1 conductors. 3. PAIRS/TRIADS: Each pair/triad is twisted to a 2 in. lay. Color coded: pairs black/white, triads black/white/red with alphanumeric designation (1-ONE). 4. ASSEMBLY: The individually shielded pairs are cabled together with non-hygroscopic and flame retardant fillers as necessary to form a circular cross section of the assembly. A binding tape, when required, shall be applied over cable core. 5. SHIELDING: The entire cable assembly is shielded with polyester backed/aluminum tape and tinned copper drain wire. 6. OVERALL JACKET: Flame retardant chlorinated polyethylene (CPE). 7. STANDARDS: Meets the requirements of UL Finished cable passes UL ,000 BTU and ICEA T , 210,000 BTU flame tests. UL listed as sunlight resistant and rated for direct burial. 8. TEMPERATURE: 90 C 9. VOLTAGE: 600 Volts Conductor Insulation Overall Jacket Nominal Size of Thickness Thickness O.D. Anixter* Weight Lbs. AWG Pairs Triads IN IN IN 1000 Ft. 2MR-1601POS MR-1601TOS MR-1602POS MR-1603POS MR-1604POS MR-1606POS MR-1608POS MR-1612POS MR-1624POS MR-1636POS MR-1602SPOS MR-1603SPOS MR-1604SPOS MR-1606SPOS MR-1608SPOS MR-1612SPOS MR-1624SPOS MR-1636SPOS *POS Pair(s) Overall Shield. SPOS Shielded Pairs with Overall Shield. TOS Triad(s) Overall Shield. NOTE: Diameters and weights may vary between manufacturers. Anixter Inc

20 FIBER OPTIC CABLE 62.5µm/125µm Loose Tube Buffer PVC/PVC TRAY CABLE Suitable for outdoor duct, indoor general purpose and aerial use. This cable meets the flame test required for 300 Volt Power Limited (PLTC) and 600 Volt (TC) tray cables and may be installed in cable tray. 1. FIBER SIZE: 62.5µm/125µm 2. CONSTRUCTION: Loose buffer with gel filling and sunlight resistant polyvinyl chloride (PVC) jacket overall. 3. STANDARDS: Meets the IEEE 383 and UL 1277 flame test requirements. UL Listed as OFN per NEC Article 770. Max. Min. Attenuation Bandwidth Max. Tensile Load Min. Nom. No. 1300nm 1300nm Installation Long Term Installation Long Term O.D. Approx. Anixter of Wt. Lbs. Fibers db/km MHz/km Lbs. Lbs. IN IN IN 1000 Ft IEEE / / IEEE / / IEEE / / IEEE / / IEEE / / IEEE / / IEEE / / Anixter Inc. 1999

21 FIBER OPTIC CABLE 62.5µm/125µm Loose Tube Buffer BELDEN TRAYOPTICS PVC Suitable for indoor or outdoor industrial installations. This cable meets the flame test required for 300 Volt Power Limited (PLTC) and 600 Volt (TC) tray cables and may be installed in cable tray. 1. FIBER SIZE: 62.5µm/125µm 2. CONSTRUCTION: Loose buffer with gel filling, central strength member, inner polyvinyl chloride (PVC) jacket, aramid yarn and orange polyvinyl chloride (PVC) jacket overall. 3. STANDARDS: Meets the IEEE 383 and UL 1277 flame test requirements. UL Listed as OFNR (2 12 fiber) or OFN (18 24 fiber) per NEC Article 770. Crush resistance: 500 lbs./inch minimum. Max. Min. Attenuation Bandwidth Max. Tensile Load Min. Nom. Approx. Belden No. 1300nm 1300nm Installation Long Term Installation Long Term O.D. Wt. Anixter Part of Lbs. No. Fibers db/km MHz/km Lbs. Lbs. IN IN IN 1000 Ft. BI I / / BI I / / BI I / / BI I / / BI I / / BI I / / BI I / / NOTE: Cable with up to 72 fibers available upon request. Anixter Inc

22 FIBER OPTIC CABLE 62.5µm/125µm Loose Tube Buffer BELDEN TRAYOPTICS CPE Suitable for indoor or outdoor industrial installations. This cable meets the flame test required for 300 Volt Power Limited (PLTC) and 600 Volt (TC) tray cables and may be installed in cable tray. 1. FIBER SIZE: 62.5µm/125µm 2. CONSTRUCTION: Loose buffer with gel filling, central strength member, inner CPE jacket, aramid yarn and orange CPE jacket overall. 3. STANDARDS: Meets the IEEE 383 and UL 1277 flame test requirements. UL Listed as OFNR (2 12 fiber) or OFN (18 24 fiber) per NEC Article 770. Crush resistance: 500 lbs./inch minimum Max. Min. Attenuation Bandwidth Max. Tensile Load Min. Nom. Approx. Belden No. 1300nm 1300nm Installation Long Term Installation Long Term O.D. Wt. Anixter Part of Lbs. No. Fibers db/km MHz/km Lbs. Lbs. IN IN IN 1000 Ft. BI I / / BI I / / BI I / / BI I / / BI I / / BI I / / BI I / / NOTE: Cable with up to 72 fibers available upon request Anixter Inc. 1999

Corflex. Continuous Corrugated Aluminum Sheathed PL, MC and MV Industrial Cables. Introduction Applications... 3

Corflex. Continuous Corrugated Aluminum Sheathed PL, MC and MV Industrial Cables. Introduction Applications... 3 Corflex Continuous Corrugated Aluminum Sheathed PL, MC and MV Industrial Cables Introduction................................. 2 Applications................................. 3 Corflex PL 300V Instrumentation