Modellbau Lindinger GmbH

Transcription

1 Welcome to Junsi icharger == Please see the release history in the help system for information about earlier releases. // Version: 3.11 // // Date of Release: 2009/08/11 // 1010B,1010B+,106B,106B+,208B *when in Li monitor Mode, no need connecting the main port if conecting the balance port. (Only for 1010B+,106B+,208B) 124: Revised setting current bug in the process of charing and discharging, and add continuous alterring function(press <Dec>/<Inc> for 3 seconds). <Thanks Charles> 125: Calibrate Vout bug manually. <Thanks Matthias Demski> 126: Decrease "R99" resistance heat by decreasing pulse duty factor. (Only for 208B) 127: Revised "BREAK DOWN" mistake caused by input voltage fluctuation. <Thanks StrykerSpeed and Charles> // Version: 3.10 // // Date of Release: 2009/07/04 // 1010B,1010B+,106B,106B+,208B *Adjust Current, Temp. Cut-Off, Safety timer, Capacity Cut-Off in course of charging and discharging. <Thanks Wyn and Charles> Method of Application: When in charging and discharging interface, press <Start> for 3 seconds, and current begins blinking. Press <Dec>/<Inc> to adjust current, and press <Start> to save

2 changes. If users press <Stop> or without any operation for 1 minute, it will cancel and quit from the changes. : Adjustment of current is only effective for charging and discharging, which will not saved as user setting. When in charging and discharging interface, press <Dec> for several times to see need-to-be changed information interface. Press <Start> for 3 seconds, and the value begins blinking. The adjust method is as same as the above. : This change can be saved as user setting. *Adjust current by scrolling. <Thanks Julez and David> *Improve the stepping speed,which can be increased or decreased more quickly than before. <Thanks Julez and marc1> 120: Revised Internal resistance measurement bug in 208B. <Thanks Charles> 121: Revised overflowing issue when the setting value of Capacity Cut-Off is more than <Thanks Johannes> 122: Revised individual cell voltage measuring bug when in Li MONITOR Mode. 123: Get rid of the user setting's clearance after upgrading. <Thanks Charles> // Version: 3.09 // // Date of Release: 2009/03/04 // 1010B,1010B+,106B,106B+ *Control the rotational speed of the fan by the temperature, which will reduce noise from the fan effectively when charging with small power. <thanks Simon> *Revised the charging mode of Lixx non-balance charge (connect the balance port): changing from the previous "stop charging if the individual cell is over-voltaged" to "keep the individual cell's voltage and current reduce". <thanks Julez> *When charging the Nixx, the output "cell offline voltage" is to logview's CellV1 passage. 116:Revised Lixx battery's wrong showed cell number in charge, fast charge mode. 117:Revised the problem of "SHORT ERROR" and "BREAK DOWN" caused by input voltage fluctuation. <thanks Julez> 118:Revised the cell wrong voltage showed on screen sometimes when Nixx charge. 119:Revised the problem of "no stopping" or the cell temperature is slightly higher when charging several series of Nixx. <thanks Stefan>

3 // Version: 3.08 // // Date of Release: 2008/11/28 // 1010B,1010B+,106B,106B+ *Add feature of monitoring internal resistance by pressing <DEC>, and in this mode, pressing <START> for 3 seconds to monitor it again. <thanks Smeagle> *Add program of shortcut mode for "Load settings" by pressing <INC>&<START> for 3 seconds, "Save settings" by pressing <DEC>&<START> for 3 seconds. *In non-balance mode, expand LiFe charging cell counts: 1010Bx(10s->12s),106Bx(6s- >8s). <thanks write2dgray> 114:Revised the button trigger from "Down" trigger to "Up" trigger. <thanks Smeagle> 115:Revised Lixx battery's setting sequence: Li Type->Current->Cell Count. <thanks Julez> // Version: 3.07 // // Date of Release: 2008/10/27 //,1010B+,106B+ *Expand output power capacity by limitting its input current, 1010B 200W-->250W;106B 180W->210W;1010B+ ->300W;106B+ -> 250W *Add program of discharge current reduce mode <thanks Julez> *Add feature of adjusting Pb charge termination voltage and support foaming charge <thanks Smeagle> *Battery pack's internal resistance measurement (per cell's internal resistance measurement only for 1010B+ & 106B+) *The minimum value of Nixx Sensitivity is changed from 3mV to 1mV The followings are existed only in 1010B+ & 106B+: *Lithium expanding discharge *Add USB port to support logview as communication port

4 112:Fixed the arithmetic problem of balance charge 113:Revised the backlight adjustment speed from 1 to 5 <thanks Julez> // Version: 3.06 // // Date of Release: 2008/07/15 // *Displayed time format changed to MMm:ss or HHh:MM for convenience. <thanks Julez> *Add feature of LiFe/Lilo/LiPo for optional to Lithium Monitoring program and Lithium Cycle program. *Add program of "Li Balance ON". <thanks Smeagle,Kgfly> 107:Modification to "Nixx Trikle", fixed the bugs of "INPUT VOL ERR". <thanks Julez> 108:Logger the character exchange pause time to 1S. <thanks write2dgray> 109:Fixed the flow logical error to "Nixx FORMING CHG". <thanks Julez> 110:Fixed the problem of confusing current display when choosing "Lixx BALANCE CHG" with high current. <thanks Julez,Kgfly> 111:Revised "User set" menu to "Settings";Intermit point information display changed from "000: mAh" to "-00005mAh 00m:50" "-" refers to discharging. <thanks write2dgray> // Version: 3.05 // // Date of Release: 2008/06/11 // *Add "Foam Cut" function.(gratitude to Julez) *Alteration to program of Lixx Storage during discharging progress, the progress won't stop even the voltge reach termination voltge, it will continue the process

5 after three beeps souding, and won't stop until the current reach 1/10C.(Gratitude to Fab66) *Toggle back to the last viewed parameter via the DEC button.(gratitude to Kgfly) 105:Set name can be delete in the program of"save SETTING". // Version: 3.04 // // Date of Release: 2008/06/11 // *Adjustable temination voltage of Lithium.LiFe( V), Lilo( V), LiPo( V) <thanks Julez,Kgfly> *Users can choose any of the LiFe/Lilo/LiPo type in Lithium charge/discharge program. <thanks Julez> *Users can define the memory name in "SAVE SETTINGS" program as they like.in "LOAD SETTINGS" program,users can enter into any of the saving program after you load in the memory name. <thanks Julez,Kgfly,Thomanie> *All of settings restore to factory default after upgrading. 102:iChargers can revise the input voltage accuracy by detecting the input current, which can minish measure error. <thanks Kgfly> 103:charging progress finish hint, changed "OVER" to "DONE". <thanks Thomanie> 104:Hold the "STOP" or "START" button to start command alteration once rather than consecutive alterations. // Version: 3.03 // // Date of Release: 2008/05/22 //

6 *During charge-to-discharge cycle mode waiting time,you can stop the waiting process with pressing "Start" button for three seconds! <thanks Fab66> 100: Accidental overcharging problem occurs during the Lithium balance mode. <thanks Kgfly> 101: Problems result from the termination voltage of the charge/discharge lithium in cycle mode // Version: 3.02 // // Date of Release: 2008/05/16 // *Press the STOP botton, power the charger and it will enter into the upgrading waiting process! (You can active the PC to enter into the upgrading progress directly, only for 1010B) 099:iCharger automatically clears the charging information for NiMH,NiCd when the battery removed has been changed to continue displaying the charging information even the battery removed! <thanks Kgfly>