HYPERION HP-0610i-DUO Connections and Flow Charts

Transcription

1 HYPERION HP-0610i-DUO Connections and Flow Charts 1. DUO CHARGER LAYOUT DC INPUT CABLE 2X16 LCD PC DATA PORT TEMP1 SENSOR OUTPUT PORT 1 OUTPUT PORT 2 TEMP2 SENSOR CH Output 1 6Cell Lithium Balancer Connector Output 2 6Cell Lithium Balancer Connector

2 2. MAIN MENU FLOW HYPERION RC EOS0610iDUO MEMORY 1-2SEC DATA VIEW 1 BALANCER INFOR1-2SEC USER SET 1 Operation Start 1 Balancer Start 1 Charge Operation 1 Balancer Operation 1 CH MEMORY 2-2SEC DATA VIEW 2 BALANCER INFOR2-2SEC USER SET 2 Operation Start 2 Balancer Start 2 Charge Operation 2 Balancer Operation 2

3 3. MEMORY LiIo/LiPo/A123(LiFePO4) NiCd/NiMH Pb A V 2300 A V 2300 NiMh 7.2V 1800 Pb 12.0V BATT TYPE 1 A123 BATT TYPE 1 A123 BATT TYPE 1 NiMh BATT TYPE 1 Pb BATT VOLTS 1 BATT VOLTS 1 7.2Vpack ( 6S) 12Vpack ( 6S) BATT VOLTS 1 9.9Vpack ( 3S) BATT VOLTS 1 9.9Vpack ( 3S) BATT CAPACITY 1 BATT CAPACITY mAh 45000mAh BATT CAPACITY mAh BATT CAPACITY mAh CHG CURRENT 1 CHG CURRENT 1 1.8A 7.0A PEAK SENS. 1 TEMPERATURE 1 3mV/C CUT-OFF 50`C CHG CURRENT A CHG CURRENT A TRICKLE 1 SAFETY TIMER 1 0mA 300MIN TEMPERATURE 1 CUT-OFF 50`C TEMPERATURE 1 CUT-OFF 50`C PEAK DELAY 1 3min TEMPERATURE 1 CUT-OFF 50`C SAFETY TIMER 1 120MIN SAFETY TIMER 1 000MIN SAFETY TIMER 1 90MIN TCS CAPACITY 1 100% (SOUND) TCS CAPACITY 1 100% (SOUND) CHG CAPACITY 1 LIMITED 120%

4 4. DATA VIEW [ DATA VIEW ] 1 INPUT 0.000V OUTPUT V 1 BAT. RES 0mΩ TEMP -----`C 1 PEAK.T 000.0`C CHG TIME 1 000min 00sec CHG C mAh 1 PEAK.V 0.000V

5 5. BALANCE INFORMATION [ BALANCER ] 1 0CELLS V -2SEC 1 SEPARATE 1 SYNCARP -2SEC -2SEC SELECT [0CL] 1 VOLTAGE V AVG. V V 1 GAP V V 0CELLS [ 00.0V] 0CELLS [ 00.0V] 1 0CELLS [ 00.0V] V V Balancer Operation Balancer Operation

6 6. USER SET [USER SET] 1 TEMP `C [USER SET] 1 TEMP `C BUTTON SOUND 1 ON BUTTON SOUND 1 ON FINISH SOUND 1 TIME 5sec FINISH SOUND 1 TIME 5sec FINISH SOUND 1 MELODY 1 POWER SPLY 1 VOLTAGE 00.0V FINISH SOUND 1 MELODY 1 POWER SPLY 1 VOLTAGE 00.0V This screen accessed via CH button (2) POWER SPLY 1 CURRENT 00.0A POWER SPLY 1 CURRENT 00.0A 2POWER SHARING 1 00% %

7 7. START SET > NiCd / NiMh Battery Start [ MEMORY No.0 ] NiMh 7.2V SEC AUTOMATIC AUTOMATIC NOMAL LINEAR -2SEC OPERATION

8 > LiPo / LiIo / A123 Battery Start > PB Battery Start A V 2300 [ MEMORY No.0 ] Pb 12.0V SEC -2SEC 1 NO BALANCER 1 SOLO 1 SYNC CC/CV -2SEC -2SEC -2SEC -2SEC SELECT CELLS 1 [ 0CELLS] 00.0V DEC INC CONNECTED CELLS 1 [ 0CELLS] 00.0V [ 0CELLS] 00.0V 1 [ 0CELLS] 00.0V 2 ** BALANCER ** ** ADVISED! ** OPERATION 1 OPERATION 1 OPERATION 1 OPERATION

9 8. OPERATION and FINISH [SOLO-RUNNING] -> SOLO mode balance [SYNC-RUNNING] -> SYNC mode balance [ **COMPLETE** ] -> Balance complete LiIo -> Lithium-ion battery LiPo -> Lithium polymer battery A123 -> Lithium Fe battery AUTO : AUTOMATIC NORM : NORMAL LINE: LINEAR SOLO : SOLO SYNC : SYNC CcCv: CC-CV A123 SYNC 000:00 1 If is pressed, each parameter will scroll every 2 seconds. Output current Output voltage Connected cell number Connected Pack voltage [ BALANCER ] 1 6CELLS V A123 CHG 000:00 1 A123 CHG 000:00 1 Selected cell number cell voltage The decimal point changes to a larger square box depending on the balancing status. The meaning of the square box is cell voltage high and therefore cell is balance discharging. SELECT [0CL] 1 VOLTAGE V AVG. V V 1 GAP V V V V CAPA mAh INPUT V TEMP 0.0`C PEAK.T 0.0`C PEAK.V 0.000V BAT. RES 000mΩ TCS CAP. 000% FINISH Output current, Output voltage Charge capacity Input voltage Battery temperature Battery peak temperature Battery peak voltage Battery internal resistance TCS capacity A123 CHG 000:00 1 END:CC/CV Finish status display END:DELTA-PEAK END:CC/CV END:TEMPERATURE END:CAPACITY END:TIMER END:TCS CAP. A V SEC

10 9. Message Display INPUT VOLTAGE 1 ERROR 0.00Vi When input voltage is below 11.0V or exceeds 15V. OUTPUT BATTERY1 CONNECT ERROR When a battery is not connected to the charger s output OUTPUT BATTERY1 REVERSE POLARITY When a battery is connected to the output in reverse OUTPUT BATTERY1 OPEN CIRCUIT When a battery becomes disconnected during an operation OUTPUT CIRCUIT1 PROBLEM When the circuit of the charger has a problem OUTPUT VOLTAGE1 TOO LOW 0.00V Output voltage is lower than the selected cells or voltages OUTPUT VOLTAGE1 TOO HIGH 0.00V Output voltage is higher than the selected cells or voltages. TEMPERATURE SENSOR ERROR When the thermal probe is incorrectly connected, or the probe is defective. BATTERY TEMP TOO LOW 0.00V When the temp of the battery is too low ( below -10 C at idle mode and 0 C during operation). BATTERY TEMP 1 TOO HIGH Battery temp is too high to be charged!

11 INTERNAL TEMP TOO HIGH When the temperature of the charger exceeds 125C. BALANCE VOLTAGE CELL(0) TOO HIGH When the balancing cell voltage is too high. SYNC COMMAND ERROR PAUSE... 1 CHARGER TOO HOT When communication is not properly working at SYNC mode. Check batteries to insure no damage, wiring proper, etc Charger temp is too high. Pause until temp drops