Enquiry Sheet for LiSA-Lift Controller to EN81. Tel: Fax:

Transcription

1 Enquiry Sheet for LiSA-Lift Controller to EN81 Company: ORDER-Nr.: Contact: Date: Tel: Fax: Works No.: SITE Ref: Offer required by : ORDER Ref:: Additional standards: EN81-70 Passenger access, to include disabled access. EN81-72 Fireman Lift Scope of supply: Controller with LiSA-OP s (pls. fill out the LiSA forms) OP s by s (pls. provide detailed information (Sketches / Datasheets): 24V/npn? LiSA BUS-System (3 wire-bus shaft loom) complete shaft installation only Pit Box - with m cable to controller Machine room wiring Car wiring Shaft Lighting Lift: Traction MRL Hydraulic M/R on top M/R below No. of Floors : No of group cars : (2,3,4,...) max.8 No. of Access: Speed: m/s Duty Load: kg No. of Landing Pushbuttons : Shaft height: m Travel height: m Shaft selection: LiSA-AWG (Absolute encoder) Standard shaft selection (with Flags) Floors & Doors: (max. 48 Floors) Door 1 Door 2 Door 3 Shortest floor to floor: mm Safety circuit: 230VAC 110VAC V Car Door (s) : one two three without Door controller: Sematic Drive System SiemensAT25 : Sematic Brushless Fermator / Kleemann VVVF 4 Sematic Encoder Selcom RCF1 Door motor 3x380V Wittur Prisma : In = QKS-8 QKS-9 Meiler Motor brake 80 VDC Door detector : LiSA 917 OR Mod: Power supply V Outputs: Relays npn-signal (preferred) pnp- Signal Landing doors: Inspection Box Automatic Swing / Folding 180 VDC 230 VAC 3*380 V sonst. V Inspection function in COP Required functions : Car ventilator shutoff sec. after Trip end Alarm- misuse function Light shutoff sec. after Trip end Arrival gong Overload contact Full-load contact NO load contact Load weighing device: Mod: Power supply: V Outputs: Relay contact npn-signal ( preferred) pnp-signal Seite 1 von 7 Seiten

2 Hydraulic Lift : Motor details: Power: kw A Star / Delta Soft start in W3 from LiSA Soft start by s Mod: Giehl / ALGI: 230VAC 185VDC AZRV AZRS Leistritz / Kleemann : 230VAC 185VDC volt free PZ9922 (npn) PZ9912 (pnp) DS117 volt free UD7 (pnp) Oildinamic / GMV GEV volt free ER3100 K4TA on Block VDC Beringer: ELRV Delta controller Power unit from LiSA DZE ELRV 1 / 2 Power unit by-s DZE2 pre wired DZ/DP volt free OTHER: Mod: Valve voltage : V Overload contact Oil cooling / heating Oil Cooler (3x V) Mod: In = A ( Motor contactor by LiSA) Oil heating (230V) Oil cooler supplied by LiSA OPTIONS: Micro-Levelling motor: P = kw In = A Override Button for minimal pressure Auto. emergency lowering with UPS, to include. Auto. Door-opening for 230V door motors prepared for Wittur HSK for hydraulic lifts ( reduced O/H ) prepared for Wittur HSG for hydraulic lifts ( reduced PIT ) floor locking ( pls. provide full details of locking device ) : Shaft selection:-> car top selector block with Flags and Proximity switches / incl. brackets) required LiSA- car top encoder ( for slowdown point ) Time method (only for 2 Floors in certain circumstances) Notes: Seite 2 von 7 Seiten

3 Inverter: Mfg: MRL Traction Lift Mod: Inverter from LiSA Schneider Inverter by s delivered to Schneider Steuerungstechnik Inverter by s NOT delivered to Schneider Steuerungstechnik Inverter to be built into cabinet Main isolator built into cabinet Line filter to be built into cabinet Machine: Mod: Power: kw Nominal current : A Brake: 207 VDC 24 VDC BSV(Brake controller).: Type: Brake motion monitoring (Open/Close) Brake Pad wear monitoring 3x Discs / Solenoids Taco / Encoder: Type: supplied by LiSA Motor ventilation: 230 V Evacuation protocol / Passenger release Evac. using UPS (230V) to next floor Evac. using UPS (230V) to Floor: Evac. using Inverter Intermediate circuit / battery power, to next Floor Evac. using Inverter Intermediate circuit / battery power, to Floor : Manual brake release using UPS (230V) supply (with Transformer). Monitoring of the Evacuation procedure & lift Levelling confirmation : Tensioning pulley kit with Encoder for Emergency release display by-s with integrated Encoder for Emergency release display Tensioning pulley on guides Tensioning pulley on pit floor Infra-Red Camera system with Screen to Monitor the traction pulley (control cabinet depth min. 230mm) RCP module to program Ziehl-Abegg Inverter supply in-built Emergency release display unit Built into cabinet cabinet prepared for RCP (RCP by-s) Supplied as a Hand-Held device Control cabinet: Size: 306w 1700h 130d mm 306w 1700h 130d mm 400w 2000h 260d mm Special size: w: * h: * d: Colour: Pigeon grey, RAL-Nr: Material: Painted steel Stainless steel, Grit / Pattern : Supply connection cables (Control) Cabinet Inverter Supply connection cables (Power) Cabinet Inverter Distance between Cabinet Inverter : m Pulses from Inverter (motor Encoder) LiSA-car top Encoder Encoder mounted on OSG. ( for v >2 m/s) NOTES: Seite 3 von 7 Seiten

4 Traction lift Machine: Mod: Power: kw Running current: A Brakes : 180, 207 VDC 230VAC 3*380 V : V 48VDC 60VDC BSV-Device prep. for BSV Brake pad monitoring Brake Pad wear monitoring Encoder: without ( Open Loop ) Mod: LiSA to supply Encoder Supply mounting kit Paguflex M. kit -> Encoder Shaft: M Offset toothed belt M.kit-> Belt dimensions: mm Un-regulated traction lifts: 2-Speed 2x Motor protection switches (fast and slow) 1-Speed Motor protection switch Regulated traction lifts: Inverter: Mfg: Mod: Inverter from LiSA Schneider Inverter by s delivered to Schneider Steuerungstechnik Inverter by s NOT delivered to Schneider Steuerungstechnik Inverter to be built into cabinet Chopper to be built into cabinet Line filter to be built into cabinet Motor protection: Thermistors Motor Ventilation 230 V thru Thermo contacts 3x 380 V thru Controller with run-on Emergency braking / in the Up- direction: Thyssen NBS Control unit NBS by-s Control unit built into cabinet Mayr-Robastop Rectifier mod Mayr by-s just preparation Rectifier mod Mayr supplied by LiSA Bode rope brake : Evacuation protocol / Passenger release Evac. using UPS (230V) to next floor Evac. using UPS (230V) to Floor: Evac. using Inverter Intermediate circuit / battery power, to next Floor Evac. using Inverter Intermediate circuit / battery power, to Floor : Manual brake release using UPS (230V) supply (with Transformer) Notes: Pulses from Inverter (motor Encoder) LiSA-car top Encoder Encoder mounted on OSG. (for v >2 m/s) Seite 4 von 7 Seiten

5 Specification & Controller Functions Contact in the M/R: Speed Governor STOP switch : Contacts in Shaft : Speed Governor Upper limit switch Inspection limit switch Tensioning Device Lower limit switch Pit ladder Pit Door Pit STOP Rope plate (broken rope) additional mech. Device : Contacts on Car: Safety contact Emergency limit switch 2nd STOP for 2nd Access Broken rope combined Safety and Broken rope switch Dividing door (in Car) Movable sill Inspection limit switch Folding toe guard with safety switches Speed governor on Car frame (pls. provide full details) : Controller: Trip Counter in Cabinet Trip Counter in Door Hour Counter in Cabinet Hour Counter in Door Cabinet lighting Cabinet door hung Left (Standard: Right) Cabinet isolation Wiring halogen-free (LSF) Main Isolator on Right side (Standard) Main Isolator on Left side Main Isolator built into door NO main Isolator in controller prepared for installation bridge Main Isolator ( fitting on site by s ) Functions: Door pre-opening Recall (with Hand-Held) Control / Light Off in cabinet door All faults logging Status display Cam reversal for Emergency release (180 VDC) Functions: Re-levelling for traction lift Levelling indicator (req. for Hydro) Button for OSG remote Test (230V) Button for OSG remote Release (230V) OSG with sinking prevention (12VDC) Evacuation protocols: (written description required in all cases) Emergency power (Diesel) / Evacuation Floor: Emergency power (Diesel) with sequential Evac. Fire evac. Floor: Dynamic Fire evac. (pls. provide details of system) Fire signal from BMS (NC / NO) Emergency calls / communication: LiSA-System Siedle Micome : prepared for Servitel prepared for Teleservice prepared for OTIS-REM : Remote monitoring: LiSA-System Other: Seite 5 von 7 Seiten

6 Installation material LiSA-travelling cable m halogen free ( LSF ) LiSA-shaft selection complete with Flags, Brackets and Magnets Bracket angled, C-Profile inside angled, C-Profile outside angled, C-Profile inside / outside Installation material Machine Room : Complete package halogen free Contents: pls. cross if partial delivery required.: 10 / 20 m 4 x mm², Cables for motor / pump 10 m 4 x mm² shielded Cables for frequency controlled traction motor 25 m 3 x 0,75 mm², flexible Cables for valves 25 m 3 x 0,75 mm², flexible Cables for Overload switch and thermistors 25 m 3 x 0,75 mm², flexible Cables for brakes, thermistors, OSG, 10m Trunking (60 x 100 mm) 50 pcs knock-in fixings (6 x 35 mm²) 10 pcs Terminals motor -> mm² 100 pcs Terminals -> 0,75 mm² 50 pcs Cable ties OPTIONS (cross as required): 5 m 5 x mm², flexible Connection to main Isolator in M/R 5 pcs Terminals -> mm² - additional terminals for Isolator cabling 5 m 3 x 1,5 mm², flexible Connection to external Car lighting supply 10 m 7 x 0,5 mm², flexible Screened cable to motor encoder Main Isolator in separate housing EMC rated main Isolator in separate housing Installation material - Car: Complete halogen free (LSF) Contents: pls. cross if partial delivery required.: Door controller: 5m / Entrance 12x 0,75mm², flexible Connection to VF control 380V motors 5m / Entrance 5 x 0,75mm², flexible Connection to 3*380 V motor 25m / Entrance 2 x 0,75 mm², flexible Connection for door switches, photocell, door close limiter 5 m / Lift 3 x 0,75 mm², flexible Connection to car light Optional (please select as required) 5m/ Entrance 3 x 1 mm², flexible Connection for door Cam. Transformer and Dimmer for Halogen lighting VA Other: Seite 6 von 7 Seiten

7 Installation material: Complete shaft installation ABOX-3 Shaft height Sh = m Distance controller Shaft = m Position controller: top bottom in landing Complete shaft installation Shaft installation halogen free Package-contents: ABOX-3 with prepared connections to door-safety circuit, door-grounding, UP limit switch, speed governor contact, remote release, resetting, shaft light and one freely disposal wire, Pit control box with prepared connections to door-safety circuit, door-grounding, DOWN limit switch, tension device contact, Optional (pls. cross if required) Door contact wire for swing door side1 Latch wire for door side-2 Door contact wire for swing door side2 Wire to buffer contact Wire to pit ladder switch Second STOP-switch lead Trunking (60x40) & knock-in fixings Flex tube for landing button leads 2 limit switches with bracket 1 limit switch with bracket 1 limit ramp Speed governor tension weight contact with mounting angle Complete shaft lighting Pre- wired system Contents: Fix light (ready to plug) (L=1200mm, 36W) with PVC cover, with plugs, screws, 2m prewired cable between lights Conventional system Light (L=1200mm, 36W) with PVC cover and fixing material 3x1.5 mm 2 cable wire ends Other: Seite 7 von 7