Thyristor Power Controllers for Resistive and Inductive loads (Product Code 21.3)

Transcription

1 Thyristor Power Controllers for Resistive and Inductive loads (Product Code 21.3) 1

2 Model Wise Descriptions: Sr. No Model Product Description POW-1 Single Phase SCR Power Controller for single phase heaters POW-1-CL Single Phase SCR Power Controller for single phase heaters with current limit and current trip features POW-2 Two Phase SCR Power Controller for two phase heaters POW-2-CL POW-3S POW-3S POW-3S-4 - CL POW-3S-3 -CL POW-3D POW-3D-6 -CL POW-3D POW-3D-3- CL Two Phase SCR Power Controller for 2 phase heaters - with current limit and current trip features. connected in 4 wire Star with neutral configuration. connected in 3 wire Star without neutral configuration. connected in 4 wire Star with neutral configuration with current limit and current trip features. connected in 3 wire Star without neutral configuration with current limit and current trip features. connected in open Delta 6 wire configuration connected in open Delta 6 wire configuration with current limit and current trip features. connected in close Delta 3 wire configuration connected in close Delta 3 wire configuration with current limit and current trip features. Note: 1) For single phase heaters for 4 to 8 KW our low cost model LTC-16 can be considered. 2) For three phase heaters for 9 to 12 KW out low cost model POW-12 can be considered. 3) For physical dimension of specific model, please contact us for mechanical drawing and mounting Dimension. 2

3 Features: 5 Amps to 500 Amps capacity (1KW to 360KW). Single phase / 2 phase / 3 phase versions. Suitable for 3 or 4 wire star configuration / 3 or 6 wire delta configuration. Auto / Manual operation. Accepts (4-20)mA/ (0-5)VDC / (0-10)VDC control input (user selectable) Soft start and step less smooth control. Adjustable power and current limit. Isolated heat sink for safety. Simple and Modular design for easy servicing of firing cards and thyristors. Ideally suitable for resistive, transformer, inductive or heating loads like Silicone Carbide and Molybdenum which exhibits significant changes of resistance with increase in temperature. Applications: Thyristor Power Controller has a varied application and can be used with heating elements like nichrome, Kanthal, Super Kanthal, Silicon Carbide, Molybdenum, Infra Red, etc. where precise and accurate power and temperature control is required. There is a significant electrical power savings with respect to conventional contactor type temperature control system. Thyristors have many direct and indirect advantages compared to electro - mechanical contactor. Description of Thyristor Power Controller: Libratherm offers ready to use SCR power controller for electrical heating loads ranging from 3 KW/Single phase to 360KW/3-phase. This power controller module comprises of suitable triggering card model LTC-12 or LTC-13 or LTC-15 or LTC-18, suitably rated back to back connected SCR modules (with electrically isolated base, mounted on the heat sink, input and output clip-on type heavy duty connectors or copper bus bars, semiconductor fuses and thermal cutouts. The entire assembly is mounted on MS powder coated enclosure, which in turn can be easily mounted inside the closed control panel as desired. Complete ready to use control panel with suitable PID / Program temperature controller can also be supplied as per the user s specifications and requirement. Technical Specifications: Available Ratings Available Configuration Control Action Control Signal Output Smooth Control Current Control Settings 1KW Single phase to 360KW Three phase Single phase, Two phase, Three phase (3 or 4 wire star and 3 or 6 wire delta) Phase angle control (self synchronized) (4-20)mA / (0-5)VDC / (0-10)VDC / Potentiometer user selectable 0 to 240VAC or 0 to 415VAC variable voltage proportional to the control signal. Adjustable Ramp Up and Ramp Down Time for soft increase and decrease of output voltage. (Settable in the range of 2 to 20 seconds Using on card Current Limit and Trip settings. (LTC-13 and LTC-18) For adjusting voltage and current per phase using on card presets 3

4 Load Type Aux. Supply Voltage Available Models Other accessories provided with each power controller Size (Power Controller) Mounting Suitable for both resistive and inductive / transformer load 240VAC +/- 10%, 50/60 Hz As given in the above table (Under Model wise description) a) RC snubber / MOV across the SCRs to protect against voltage transients dv/dt b) Thermal cut out switch on the heat sink to protect thyristors against overheating. c) Cooling fan on heat sinks for all power controllers. d) Heavy duty input/output terminals or Copper or Aluminum Bus bars for supply and heater Connections. As per Std. (Sizes can be given on request based on the model) Power controller can be mounted on the base plate of the control panel KW (Kilowatt) wise selection table for Resistive/Inductive loads: Load Current per phase to Neutral or Phase1 to Phase 2 AMPS(Max) 25A (SKKT 27) 50A (SKKT 57) 95A (SKKT 106) 146A (SKKT 162) 246A (SKKT 273) 297A (SKKT 330) 516A (SKKT 573) Single Phase 1-5 KW (POW1.1) 6-12 KW (POW1.2) KW (POW1.3) KW (POW1.4) KW (POW1.5) KW (POW1.6) KW (POW1.7) 415VAC Two Phase 3-10 KW (POW2.1) KW (POW2.2) 22-40KW (POW2.3) KW (POW2.4) KW (POW2.5) KW (POW2.6) KW (POW2.7) POW-3S-4 POW-3S-3 POW-3D-3 Three Phase 3-17 KW (POW3.1) KW (POW3.2) KW (POW3.3) KW` (POW3.4) KW (POW3.5) KW (POW3.6) KW (POW3.7) POW-3D-6 (open Three Phase 3-30 KW (POW6.1) KW (POW6.2) KW (POW6.3) KW (POW6.4) KW (POW6.5) KW (POW6.6) KW (POW6.7) To get the quote or to place the order please specify the item code given in the bracket in the above table or refer ordering information given below. 4

5 User can select the required power controller either by actual current through the heaters or by KW of the heaters. Single phase, two phase or three phase selection can be done by selecting appropriate model based on the desired configuration, from the table given above. If the heaters are designed at different voltage other than 240VAC or 415VAC, still the selection can be made, based on the actual current flowing through the heaters at the desired voltage level. For inductive / transformer load, the desired KW can be selected as per the requirement. User must use suitable ratings of MCB or MCCB in series with the thyristors. Ordering Information: MODEL POW-1 POW-1-CL POW-2 POW-2-CL POW-3S-4 POW-3S-3 A- ITEM CODE POW1.1 to POW1.7 POW2.1 to POW2.7 POW3.1 to POW3.7 POW-3S-4-CL POW-3S-3-CL POW-3D-6 POW-3D-3 POW3.1 to POW3.7 POW6.1 to POW6.7 POW-3D-6-CL POW-3D-3-CL POW6.1 to POW6.7 5

6 Examples: MODEL POW-1 POW-2-CL POW-3S POW-3D-3 -CL POW-6D A- ITEM CODE POW1.2 POW2.4 POW3.2 POW3.6 POW6.3 Example Ordering Code Description 1 POW-1-POW1.2 2 POW-2-CL-POW2.4 3 POW-3S-POW3.2 4 POW-3D-3-CL-POW3.6 4 POW-6D-POW6.3 This is single phase AC power controller suitable for 6 to 12 KW heater 240VAC This is two phase AC power controller with current control and overload protection suitable for 41 to 60KW heater 2 phase 415VAC. This is three phase AC power controller suitable for 3 wire or 4 wire configuration of 41 to 60KW heater 3 phase 415VAC. This is three phase AC power controller with current control and overload protection suitable for 3 wire close delta configuration of 177 to 213KW heater 3 phase 415VAC. This is three phase AC power controller suitable for 6 wire open delta configuration of 64 to 120KW heater 3 phase 415VAC. Technical specifications are subject to change and revision, due to product up gradation. 6