B.M.P. DOORS LTD INDUSTRIAL RAPID DOORS

Size: px
Start display at page:

Download "B.M.P. DOORS LTD INDUSTRIAL RAPID DOORS"

Transcription

1 B.M.P. DOORS LTD INDUSTRIAL RAPID DOORS Web site : info@bmpdoors.co.uk THERMICHROLL KOMBY ENGLISH INSTALLATION MANUAL IMPORTANT Read this manual carefully before installing the product The service of installation must be performed only by authorized personnel and in accordance with national wiring standards. After reading the entire manual, keep it for future reference.

2 INSTALLATION INSTRUCTIONS - Always use a power circuit specifically dedicated to the door. For wiring follow the manufacturer's instructions. - Tighten the screws of the electrical terminals to prevent loosening. - Make sure the power source has the required capacity. - Make sure the thickness of the cable conforms to what is stated in the specification of the power source. - Never install a differential circuit breaker in wet or damp areas. EQUIPMENT NEEDED 1 Tape measure 10 Level 2 Suitable lifting equipment (Genie, Forklift, Scissor Lift etc) 3 Screwdriver set 12 Tester 4 Steel drill 13 Hammer 11 Set of spanners (17 mm, 13 mm, 10 mm, 8 mm) 5 Hammer drill 14 Cordless screwdriver 6 Drill bits (Steel and concrete) 15 Grinder 7 Scissors 16 Silicone gun 8 Cable cutters 17 Pliers 9 Vices / Clamps 18 Set of Allen keys Elevator Forklift WITH INTENTION TO CONTINUOSLY IMPROVE ITS SERVICE, B.M.P. SRL. RESERVES THE RIGHT TO CHANGE THIS MANUAL AT ANY TIME, WITHOUT PRIOR NOTICE. IMAGES USED IN THIS MANUAL MAY BE SLIGHTLY DIFFERENT FROM YOUR PRODUCT AND ARE USED FOR ILLUSTRATIVE PURPOSES ONLY. 2 Installation manual

3 ASSEMBLY OF THE MECANICAL PART Door parts placed on the ground Attach the base plates to the wall. Fixing points. installation manual 3

4 ROLL-UP SHUTTER DOOR PLATE HOLDER ASSEMBLY Motor side Bearing side - 30 Bearing Side - 40 Fix the Dynamicroll support plates to the Roll-Up Shutter plate holders. 4 Installation manual

5 Rotate the motor using the chain, until it reaches the horizontal position. Insert the bearing on the opposite side of the shaft. Lift up and install the roll-up shutter. Assemble the components of the Dynamicroll door. installation manual 5

6 INFRARED PHOTOCELLS - BP100 NOTE: IN CASE OF OTHER PHOTOELECTRIC SENSORS INSTALLED NEARBY, YOU MAY EXPERIENCE DIFFICULTIES DUE UNCONTROLLED BEAM REFLECTIONS. 9 CONTROL BOARD LEGEND CONTROL CARD 6 MOTOR BRAKE TERMINAL FRAME (N 30-31) + FLASHING LIGHTS (N 29-30) 2 CONTROL CABINET 7 CONTROL CABINET LOCK 3 MOTOR TERMINALS (U-V-W) 8 START BUTTON 4 ISOLATOR 9 EMERGENCY BUTTON 5 EARTH TERMINAL 10 6 Installation manual

7 CONTROL CARD TERMINAL WITH LIMIT SWITCH Terminal N CONNECTION 1 +12V DC 100mA max. 2 0 V DC 100mA max. 3 Not used 4 5 SIGNAL - (option used ) door open signal - (option used ) door close signal 6 Not used 7 Photocell/safety sensor or safety edge N.C. 8 Opening command, radar, push button, pull cord etc N.O. 9 Not used 10 Not used 11 Start opening (standard) / closing option in use N.O. 12 Pedestrian start N.O. 13 Common inputs (+12Vdc) 14 Photocell N.C. 15 Common inputs (+12Vdc) 16 Stop N.C. 17 Slow down opening limit switch N.C. 18 Slow down closing limit switch N.C. 19 Opening limit switch N.C. 20 Closing limit switch N.C V ac power. Accessories 300mA max V ac power. Accessories 300mA max SIGNAL: open door signal Jumpers inputs N.C. not used Terminal N CONNECTION 23 Motor phase U 24 Motor phase V 25 Motor phase W 26 Power phase 230Vac 27 Neutral phase 230Vac 28 GROUNDING TERMINAL 29 Flashing light 230VDC 30 Flashing light/brake phase (COMMON) 31 Brake 105VDC installation manual 7

8 PRE-WIRING WITH LIMIT SWITCH 8 Installation manual

9 CONTROL CARD TERMINAL WITH ENCODER Terminal N CONNECTION 1 +12v DC 100mA max. encoder red cable 2 0 V DC 100mA max. encoder black cable 3 Not used 4 5 SIGNAL - (option used ) door open signal - (option used ) door close signal 6 Not used 7 Photocell/safety sensor or safety edge N.C. 8 Opening command, radar, push button, pull cord etc N.O. 9 Not used 10 Not used 11 Start opening (standard) / closing option in use N.O. 12 Pedestrian start N.O. 13 Common inputs (+12Vdc) 14 Photocell (no jumpers photocell with encoder) N.C. 15 Common inputs (+12Vdc) 16 Stop N.C. 17 Encoder green cable 18 Encoder yellow cable 19 Not used 20 Not used V ac power. Accessories 300mA max V ac power. Accessories 300mA max SIGNAL (option used )closed door signal Jumpers inputs N.C. not used (no jumpers photocell with encoder) Terminal N CONNECTION 23 Motor phase U 24 Motor phase V 25 Motor phase W 26 Power phas e 230Vac 27 Neutral phase 230Vac 28 GROUNDING TERMINAL 29 Flashing lights 230VDC 30 Flashing lights/brake phase (COMMON) 31 Brake 105VDC installation manual 9

10 PRE-WIRING WITH ENCODER SCREEN ENCODER CABLE MUST BE CONNECTED TO TERMINAL NO. 2 (0Vdc) IN THE CARD 10 Installation manual

11 SIGNAL LED LD2 LD3 LD4 LD5 LD6 LD7 LD8 LD9 LD10 LD11 LD12 LD13 LED CLOSING LIMIT SWITCH LED OPENING LIMIT SWITCH LED SLOW DOWN CLOSING LIMIT SWITCH LED SLOW DOWN OPENING LIMIT SWITCH LED STOP LED ALIGNED PHOTOCELL LED PEDESTRIAN START LED START NOT USED NOT USED LED OPENING COMMAND LED PHOTOCELL/SAFETY SENSOR installation manual 11

12 12 CURTAIN INSERTION PROGR. BUTTON (P3) P1 OPEN P2 CLOSE CLOSING BUTTON (P1) OPEN ING BUTTON (P2) REVERSE CURTAIN TENSIONING AND COLUMNS FIXING TELO MONTANTE MOLLA GUIDA MAX! 12 Installation manual

13 B 500 OPEN (green) LIMIT SWITCH ADJUSTING SCREWS SLOW DOWN OPENING (white) SLOW DOWN CLOSING (grey) CAMMES CLOSE (brown) COMMON (yellow) installation manual 13

14 LIMIT SWITCH SETTINGS SETTING OPEN GREEN CABLE (C1) LED OK 1) SETTING SLOW DOWN OPENING WHITE CABLE(C2) mm LED OK 2) SETTING SLOW DOWN CLOSING GREY CABLE (C3) LED OK 100 mm PHOTOCELL 3) SETTING CLOSE BROWN CABLE (C4) LED OK 14 Installation manual

15 PLANNING WITH LIMIT SWITCH 1 2 LED OK DOOR CLOSE 3 4 HOLD FOR 10 SECONDS FAST FLASHING 5 6 PRESS START BUTTON OK DOOR OPEN 7 8 WAIT BREAK TIME PRESS START END installation manual 15

16 SETTING WITH ENCODER 1 2 PRESS DOOR CLOSE HOLD FOR 20 SECONDS 3 4 PRESS FAST FLASHING 5 6 PRESS OK CONFIRM THAT THE DOOR IS OPEN 7 8 PRESS WAIT BREAK TIME CONFIRM BREAK TIME 9 10 START CURTAIN STOPS AT PHOTOCELLS LEVEL 16 Installation manual

17 SETTING POSITION OPEN AND CLOSE WITH PROGRAMMER (only with encoder) ONLY AFTER PROGRAMMING THE ENCODER INSERT PROGRAMMER IN THE CONTROL CARD PLUG * +/- 10qc = ~ 1cm (*) OPEN RIDE VALUE INDICATIVE ONLY * +/- 10qc = ~ 1cm (*) CLOSE RIDE VALUE INDICATIVE ONLY installation manual 17

18 ATTENTION: CORRECT POSITION CLOSED DOOR YES NO BALLAST TUBE ATTENTION: CORRECT POSITION OPENED DOOR YES NO 18 Installation manual

19 SETTING HIGHEST SPEED (System parameters) MOTOR TYPE : 1,5 KW 50/60Hz PARAMETER FREQUENCY OPEN FREQUENCY CLOSE FREQUENCY SLOW DOWN OPEN FREQUENCY SLOW DOWN CLOSE FREQUENCY MAX SPEED HZ 70HZ 40HZ 30HZ 30HZ MOTOR TYPE : 0,75 KW 50Hz PARAMETER FREQUENCY OPEN FREQUENCY CLOSE FREQUENCY SLOW DOWN OPEN FREQUENCY SLOW DOWN CLOSE FREQUENCY MAX SPEED HZ 60HZ 30HZ 25HZ 25HZ PARAMETERS TO BE RESPECTED (System status) POWER MOTOR (Opening door) 1.5KW = MAX 8.5A (*) 0.75KW = MAX 4.5A (*) (*) IF THE VALUE EXCEEDS THAT SHOWN LOWER OPEN FREQUENCY. POWER BUS VOLTAGE (Opening door) MIN 280V(*) (*) IF VALUE DROPS BELOW THATSHOWN CHECK THE POWER SUPPLY CIRCUIT (CABLES SECTION 2.5MM FROM MAIN SOURCE, POWER SUPPLY VOLTAGE ETC.) installation manual 19

20 PLANNING PEDESTRIAN OPENING WITH ENCODER 1 2 PRESS DOOR CLOSE 3 4 PEDESTRIAN HEIGHT PRESS 5 PRESS 6 WITHIN 5 SECONDS SLOWLY FLASH CONFIRM PEDESTRIAN POSITION 7 8 PRESS CONFIRM BREAK TIME WAIT BREAK TIME END 20 Installation manual

21 PLANNING PEDESTRIAN OPENING WITH LIMIT SWITCH 1 2 PRESS DOOR CLOSE PRESS 10/15 SEC. 3 4 PRESS FAST FLASH 5 6 PEDESTRIAN HEIGHT PRESS CONFIRM PEDESTRIAN POSITION 7 8 PRESS CONFIRM BREAK TIME WAIT BREAK TIME END installation manual 21

22 CONNECTIONS WITHOUT ELECTRICAL PRE WIRING WIRING CABLE: Motor cable 3x1.5 screened cable (screen grounded) Limit switch cable (where installed) 5x0,5 Encoder cable (where installed) 4x0,5 screened cable (screen grounded) Break cable 2x1,00 screened cable Flashing light cable (screen grounded) 2x1,00 screened cable (screen grounded) Photocell receiver cable 3x0,5 Photocell transmitter cable 2x0,5 Motor safety switch cable 2x0.5 Button/anchors cable 2x0,5 Radar cable 4x0,5 Cable lines: - First tube line: motor, brake and flashing light cable ( High voltage 230V) - Second tube line: Photocell,limit switch, push buttons, radar etc. ( Low voltage 12-24V) BMP srl IS NOT RESPONSIBLE IF THE DOOR DOES NOT WORK WHEN THE REQUIREMENTS ARE NOT OBSERVED MOTOR TRIANGLE CONNECTION 22 Installation manual

23 DOOR ELECTRICAL SYSTEM MOTOR BOX WIRING installation manual 23

24 SENSOR NO TOUCH 24 Installation manual

25 LIMIT SWITCH CONNECTION C1 C2 C3 C4 F1 F2 F3 F4 FC OPENING LIMIT SWITCH SLOW DOWN OPENING LIMIT SWITCH SLOW DOWN CLOSING LIMIT SWITCH CLOSING LIMIT SWITCH CONNECTION N.C. CONNECTION N.C. CONNECTION N.C. CONNECTION N.C. CONNECTION COMMON - ADJUSTABLE AUTOMATIC CLOSURE DIP SWITCH (DS) To set this function put the dip Switch1 to ON - STEP BY STEP (*) Functioning mode set by the factory To set this function put the dip switch 1 to OFF ATTENTION!!! THIS FUNCTION DOES NOT PERFORM THE AUTOMATIC CLOSURE FUNCTIONING WITH NEGATIVE ENGINE BRAKE To set this function put the dip switch 2 to OFF FUNCTIONING WITH POSITIVE ENGINE BRAKE (*) To set this function put the dip switch 2 to ON (*) set it only if you have a door with COUNTERWEIGHT to open the door in case of power cut to the control board installation manual 25

26 SAFETY RESISTIVE EDGE RECEIVER TRANSMITTER RESISTIVE EDGE RESISTIVE EDGE VALUE BETWEEN 8.1 AND 8.4 kω (Tester on 20kΩ) ATTENTION ALWAYS CHECK THE RESISTIVITY BEFORE CONNECTING TRANSMITTER AND RECEIVER TRANSMITTER CONNECTION NO JUMPER PROG RESISTIVE EDGE INSIDE CURTAIN 26 Installation manual

27 RECEIVER CONNECTION CODE MEMORY A) Press PROG (transmitter) until you hear a beep B) Press PROG (in 5 sec max) (receiver) until you hear a beep C) Wait 10/15 sec D) LD 13 (resistive edge) ON TRANSMITTER MAXIMUM DISTANCE BETWEEN RECEIVER AND TRANSMITTER 8 METERS installation manual 27

28 MANUAL OPERATION RESET CONTROL CARD CLOSE BUTTON (P1) OPEN BUTTON (P2) - SWITCH OFF THE POWER TO THE CONTROL CARD - PRESS AND HOLD BUTTONS P1 & P2 - SWITCH THE POWER BACK ON TO THE CONTROL CARD WHILST STILL PRESSING THE BUTTONS P1 & P2 - KEEP PRESSED FOR 5-6 SECONDS - RESET COMPLETE, RESET ENCODER IF FITTED SAFETY GENERAL RULES Before any intervention the maintenance engineer must: o Cordon off area and affix the right signs in order to signal the maintenance works on the door o o PERIODICAL CHECKS AND MAINTENANCE Check that the electricity power is disconnected before you start the maintenance Check that they fully understand the maintenance required and have read and understand this manual o The maintenance man can t use the electrical fittings without a declaration of his proved experience. Don t allow unauthorized people to repair or maintenance the doors. Read the manual before maintaining the doors. During maintenance don t use heat sources that could start fires. During maintenance do not weld The presence of the maintenance staff around the door must be limited. The presence of other people around the door is necessary only to support the maintenance staff 28 Installation manual

29 GENERAL CLEANING AND MAINTENANCE The general maintenance operations can be carried out by the user. The maintenance and cleaning of the door is necessary to ensure the smooth operation and continued reliability in operation of the door. COMPONENT DESCRIPTION PERIODICITY Structure Verify that the structure is securely fixed to the wall in order to avoid incidents. Clean with soft cloth any dirt or dust build up ( use soap and water if required ) If there is ice on the structure immediately remove it Six-month Clean with soft cloth ( in dusty areas could be necessary to clean Photocell and more frequently the photocells: dust on photocells could cause radar malfunctioning of the photocells) Six-month Vision Window Curtain Clean the window with a soft cloth and if necessary with soap and water ( do not use any solvent that could damage the window) Check the condition of the belts and of the curtain. Clean the curtain with a soft cloth and if necessary with soap and water ( do not use any solvent that could damage the curtain) Six-month Six-month installation manual 29

30 CHECK, PLANNED INSPECTIONS AND MAINTENANCE Only the maintenance staff or authorized people could do checks, planned inspections and planned maintenance. These operations are necessary for the validity of the warranty INTERVENTION POINT Structure Electrical components Mechanical components Curtain DESCRIPTION - Check the condition of the fixing frames, and all fixings are tight that secure the frame to the fixing face - Check that there isn t any structural damage due to impact or collisions - Check the electrical connections in the control board and check that there is no moisture inside the cabinet. - Check the electrical connections in the junction box and check that there is no moisture present - Check the condition and operation of the safety components (photocells, safety edge and emergency button etc) - Check the condition and operation of the opening components (opening buttons, radars, loop detectors etc) - Check that all the electrical cables are in good condition. - Check the condition of the motor - Check the condition of the motor brake - Check the wear and tension of the drive chain from the motor to the barrel (where applicable) - Check the condition of the Gearbox: eg oil leaks, fixing to the motor, fixing of the structure. - Check the condition of the limit switch box: eg wear of the drive chain, wear and fixing of the cogs, the correct functioning of the cams and micro switches. - Check the tightness of all bolts for any part of the structure. - Check the condition of the main barrel in the heading - Check the condition and grease the bearings. - Check the condition of the anti wear washers on the columns - Check the condition and clean the guides ( on the Dynamic doors) - - Check the condition and wear of the curtain and in particular in the areas subject to rubbing. - Check that there aren t any tears on the curtain. - Check the condition and operation of the belts, lower and upper fixing plates and of the loop belts( for the rapid pack doors) - Check the condition of the curtain bars - Check the operation of the curtain rolling around the barrel squarely - Check the tensioning of the curtain, the condition and wear of the zips ( for the dynamic doors) PERIODICITY Six-month Six-month Six-month Six-month 30 Installation manual

31 PROBLEM SOLUTION 1 THE WARNING LIGHTS IN THE CONTROL BOARD DO NOT LIGHT UP 2 THE DOOR DOES NOT MOVE WITH P1 AND P2 BUTTON 1 CHECK POWER SUPPLY ( 230 V ) 1 CHECK FUSE 2 CHECK SETTING MOTOR WITH PROGRAMMER (SETTING PARAMETERS MOTOR TYPE kw) 2 RELEASE STOP BUTTON (LED 6 turned on) 2 CHECK MOTOR CONNECTION (triangle 230V three-phase, star 380V three-phase) 3 YOU CAN NOT COMPLETE THE SETTING OF THE CARD ( with encoder) 3 CHECK WITH PROGRAMMER PARAMETER OPTION IN USE 4300 FOR SINGLE PHOTOCELL 4380 FOR DOUBLE PHOTOCELL 3 RELEASE THE STOP BUTTON (LED 6 turned ON) 3 MOVE THE DOOR WITH BUTTON P1 AND P2 OF 40/ 50 cm AND LOCATE IT ON CLOSE POSITION ( this operation is useful to recognize the encoder ) 3 VERIFY THAT THE LED LD13 (radio safety edge or sensor in the upper case) IS ON 3 IF NOT, MAKE JUMPERS 7 /13 AND CONTROL THEN THE SECURITY COMPONENTS 3 INVERT THE ENCODER CABLE (yellow with green ) 3 FOR DOORS WITH UPPER PHOTOCELL CONTROL THAT LD 3 IS OFF WHEN THE DOOR IS CLOSE 4 YOU CAN NOT COMPLETE THE SETTING OF THE CARD 4 CONTROL THAT THE LIMIT SWITCH ARE CORRECTLY REGUALATED ( if slow down closing and closing limit switch are not pressed the card can not be set) (with limit switch ) 4 VERIFY THAT THE LED LD13 (radio safety edge or sensor in the upper case) IS ON 4 VERIFY THAT THE LED LD7 (safety photocell ) IS ON 4 RELEASE STOP BUTTON (LED 6 turned on) 5 YOU CAN NOT COMPLETE THE SETTING OF THE RESISTIVE EDGE 5 VERIFY THAT THE JUMPER ON THE TRANSMITTER J1 IS TAKEN OFF 5 RESET THE OLD CODES (close the jumper "MR" press the PROG button until you hear a beeps tight series, then remove the jumper) 5 VERIFY WITH THE TESTER THE CHARGE OF THE TRANSMITTER BATTERIES 5 VERIFY IF THE RESISTENCE (8.2 KΩ) FOR THE CABLES THAT COME OUT FROM THE EDGE CHANGES IF YOU PRESS THE EDGE if it does not change control that the resistive band is perfectly flat for all the length of the black profile or take out the gum and control the integrity. 5 VERIFY THE CONNECTIONS OF THE RECEIVER 6 THE PHOTOCELL DOES NOT WORK ( LD 7 OFF) (the door does not close ) 7 THE ANTI-JAMMING SENSOR DOES NOT WORK (sensor) (the sensor does not light up) 6 VERIFY THE ALIGNMENT 6 VERIFY THE CONNECTION OF THE BLACK RECEIVER CABLE( brown +12Vdc) (blue 0V dc ) ( black: signal that it arrives to the terminal 14 in the local plant) 6 VERIFY THE CONNECTION OF THE TRANSMITTER GREY CABLE ( brown +12Vdc) (blue 0V dc) ( ATTENTION! If you invert the brown and blue cables you will damage the sensors) 7 VERIFY THE CONNECTION ( brown +12Vdc) (blue + white 0V dc ) ( black: signal that it arrives to the terminal 7 in the local plant) installation manual 31

32 8 THE ANTI-JAMMING SENSOR DOES NOT WORK (sensor) (the door closes but the sensor does not work if I press it) 8 BRING THE SENSOR CLOSER TO THE CURTAIN 8 PUT THE SENSOR FRONTALLY TO THE TUBE AXIS 8 CONTROL THE CONNECTIONS ( brown +12Vdc) (blue 0V dc ) ( black connected to the cable 7 in the local plant) 9 THE DOOR STOPS AT THE PHOTOCELL LEVEL AND COMES BACK 9 REGULATE THE SLOWING DOWN LIMIT SWITCH: IT CLOSES 10 cm BEFORE THE PHOTOCELL ( the contact switch off the functioning ) 10 THE DOOR CLOSES ONLY 50 cm AND THEN COMES BACK 10 INCREASE THE INTERVENTION TIME OF THE ANTI-JAMMING PHOTOCELL USING THE PROGRAMMER (PARAMETER SETTING- ANTI- JAMMING PHOTOCELL READING) 10 LOWER THE ANTI-JAMMING PHOTOCELL SENSOR 11 LD1 REMAINS ON( IN THE TOP LEFT- HAND ) 11 VERIFIY THE FUSE 11 THE CARD IS DAMNAGED ( replace it) 12 THE DOOR DOES NOT CLOSE AUTOMATICALLY 12 VERIFY DIP 1 ( ON = automatic ) (OFF = manual ) 12 CONTROL THE CORRECT FUNCTIONING OF THE SAFETY COMPONENTS ( LD 7 - LD 13- LD 6 on) 13 THE DOOR WORKS BUT SOMETIMES IT GETS STUCK (in any position) 13 VERIFY THE CORRECT SETTING OF THE MOTOR WITH THE PROGRAMMER (PARAMETER SETTING TYPE OF MOTOR kw) 13 CONTROL THAT THE FLASHING LIGHTS WIRES OR THE MOTOR BRAKE WIRES ARE NOT IN THE SAME CABLE OF THE PHOTOCELL AND LIMIT SWITCH (interference problem) they must have their own cable and tube,the 230V must be separated from 12-24V 13 VERIFY WITH THE TESTER THAT THE CURRENT ISN T LOWER THAN 220V (control when the door s working) if the current is lower than 220V control the input 13 VERIFY WITH THE PROGRAMMER THAT THE BUS VOLTAGE IS NOT LOWER THAN 300V (SYSTEM CONDITION BUS VOLTAGE) (control when the door s working) if the voltage is lower than 300V control the input. 13 VERIFY WITH THE PRORAMMER THE MOTOR UPTAKE (SYSTEM CONDITION- MOTOR CURRENT with motor 0,75kW can t be higher than 7A;with motor 1,5 kw can t be higher than 9A, control when the door s working) if the door exceeds the threshold lower the opening HZ 14 THE PHOTOCELL DOES NOT WORK (the door closes but the photocell doesn t reverse the curtain) 14 CONTROL THAT IN THE VICINITY THERE ARE NOT ANY OTHER PHOTOCELLS THAT COULD CAUSE REFLECTION (try to darken the photocells) 14 CONTROL THAT WITH THE PHOTOCELL CABLES THERE ARE NOT ANY HIGH VOLTAGE CABLES (motor,motor brake, flashing lights, power line) (take to the control board separated cables in different pipes, separate the low voltage 12-24V from the high voltage 100V) 14 PUT THE MINUS OF THE RECEIVER (black cable, blue wire) ground 15 WITH OPEN DOOR (locked) THE CURTAIN SLOW DOWN 15 SET THE MOTOR BRAKE (remove the fan cover and close of a quarter turn of the dial brake adjustment, then make tests to reach the optimum) Spares or Technical support Information needed: - Personal information company (or owner of the door) - Door data (serial NO.) - Description of the problem - Eventually photos 32 Installation manual

33 - RUN OPTION with control card BMP1-VO1;BMP1-V03 end BMP2-V03 WARNING: logic board is set to the value of 200 (200 DEFAULT VALUE) by the factory. - Further values must to be added. VALUE TO INSERT ON RUN OPTION FUNCTION DESCRIPTION Enable ups batteries: function opens after fixed time 2 Enable ups batteries: function opens after start command 4 Start button: it closes but it doesn t open 8 Step cycle: closing the door to start stops mid 10 Pause time and queue time after transit individually considered with zero (0) break time only 20 Move the pedestrian start on internal radar: when you need pedestrian + ups 40 It disables current control brake before starting 100 It disables timeout control alarms on movements and other inconsistencies DEFAULT SETTING 200 Pedestrian start: it opens but doesn t close, it only clears pause time 400 It disables unplugged encoder alarm 800 Frost protection function: maneuver every 15 minutes Frost protection function: running every 60 minutes Frost protection function: adjustable time You write the time in queue time after transit Encoder recognized automatically to the first movement in jog DEFAULT SETTING It reverses relay outputs for signal door state Terminals 4-5 = door open Terminals = door closed It reverses relay outputs for signal door state Terminals 4-5 = door closed Terminals = door open DEFAULT SETTING INTELOOK for BMP1-V03 end BMP2-V03(new models) Enable interlaced operation connect: Terminal no. 4 of card 1 with terminal no. 12 of the card 2 Terminal no. 5 of card 1 with terminal free of the card Terminal no. 4 of card 2 with terminal no. 12 of the card 1 Terminal no. 5 of card 2 with terminal free of the card 1 Write in the lcd menu "bussola/c.remoto terminal n. The number of terminal used INTELOOK for BMP1-V01(running model) Enable interlaced operation connect: Terminal no. 4 of card 1 with terminal no. 12 of the card Terminal no. 5 of card 1 with terminal no 13 of the card 2 Terminal no. 4 of card 2 with terminal no. 12 of the card 1 Terminal no. 5 of card 2 with terminal no. 13 of the card 1 It disables automatic alignment (after blackouts to return power) With encoders and 1 single photocell If you inserted a undervoltage motor heating (use only with installations in low temperature On pedestrian cycle, when the door is open, It closes relay door state and disables automatic The radar does not open it only performs reversals in closing installation manual 33

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

JAMISON-B.M.P. INDUSTRIAL RAPID DOORS DynamicRoll PE Installation

JAMISON-B.M.P. INDUSTRIAL RAPID DOORS DynamicRoll PE Installation JAMISON-B.M.P. INDUSTRIAL RAPID DOORS DynamicRoll PE Installation JAMISON DOOR COMPANY P.O. BOX 70 HAGERSTOWN, MARYLAND 21741 1-800-532-3667 301-733-3100 INTERNET: http://www.jamisondoor.com E-MAIL: contact@jamisondoor.com

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

CONTROL UNIT BIOS2. Manual for installation. Programmable Control board for wings gates.

CONTROL UNIT BIOS2. Manual for installation. Programmable Control board for wings gates. Programmable Control board for wings gates www.remotecontrolgates.co.uk Manual for installation Compatible from firmware version BIOS2BT02 CONTROL UNIT BIOS2 1. Introduzione The control unit BIOS2 is particularly

More information

GLM SERIES CONTROL Users Manual Rev:

GLM SERIES CONTROL Users Manual Rev: GLM SERIES CONTROL Users Manual Rev: 808062 Connecting Power Page 2 Motor Terminal Wiring Diagrams Page 3 Getting Started / Setup Page 4 1. Obstruction Detection Devices Page 4 2. Checking Power and Direction

More information

JAMISON-B.M.P. INDUSTRIAL RAPID DOORS DynamicRoll Installation

JAMISON-B.M.P. INDUSTRIAL RAPID DOORS DynamicRoll Installation JAMISON-B.M.P. INDUSTRIAL RAPID DOORS DynamicRoll Installation JAMISON DOOR COMPANY P.O. BOX 70 HAGERSTOWN, MARYLAND 21741 1-800-532-3667 301-733-3100 INTERNET: http://www.jamisondoor.com E-MAIL: contact@jamisondoor.com

More information

Table of Contents

Table of Contents Flexirun Self Repairing Rapid Roll Up Door Quick Assembling Guidebook Flexirun PLC Curtain Unwinding Detection Safety Edge Manualopen Basic or Easy 0161 432 6655 sales@indupart.co.uk /indupart /indupart

More information

EC DECLARATION OF CONFORMITY

EC DECLARATION OF CONFORMITY EC DECLARATION OF CONFORMITY Manufacturer : Address: Declares that: FAAC S.p.A. Via Benini, 1-40069 Zola Predosa BOLOGNA - ITALY 844 T control board, conforms to the essential safety requirements of the

More information

Installation Guide Rollerdor RD55 Econ Roller Garage Door

Installation Guide Rollerdor RD55 Econ Roller Garage Door Installation Guide Rollerdor RD55 Econ Roller Garage Door 1 Finished door Rollerdor RD55 Econ Roller Garage Door CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape

More information

ECONOMISER SERIES E2T USER MANUAL

ECONOMISER SERIES E2T USER MANUAL TURBO S.R.L. Electronic Control Systems for Dust Collectors e-mail: info@turbocontrols.it web: www.turbocontrols.it TEL. ++39 (0)362 574024 FAX ++39 (0)362 574092 ECONOMISER SERIES E2T USER MANUAL 24/06/2014

More information

SKC400U SLIDING GATE OPENER OWNER S MANUAL

SKC400U SLIDING GATE OPENER OWNER S MANUAL SKC400U SLIDING GATE OPENER OWNER S MANUAL IMPORTANT SAFTEY INFORMATION Installing the SKC400U Gate Opener requires wiring of standard 110V electrical lines. This should only be performed by a trained

More information

INSTRUCTION INVERTER COMPACT FOR SLIDING GATES /R0 10/11/2017

INSTRUCTION INVERTER COMPACT FOR SLIDING GATES /R0 10/11/2017 INSTRUCTI INVERTER COMPACT FOR SLIDING GATES 6-1622616 /R0 10/11/2017 2 / 20 3 / 20 1. INTRO The control unit INVERTER COMPACT is integrated in the motor KALOS XL. It is a device suitable for operating

More information

Te 803 Electronic Controller. Service, Operation & Technical Information Manual

Te 803 Electronic Controller. Service, Operation & Technical Information Manual Te 803 Electronic Controller Service, Operation & Technical Information Manual WARNING! Technical descriptions and data given in this document are accurate, to the best of our knowledge, but can be subject

More information

SLIDING DOOR OPERATOR INSTRUCTION MANUAL

SLIDING DOOR OPERATOR INSTRUCTION MANUAL SLIDING DOOR OPERATOR INSTRUCTION MANUAL (MODEL NO. 1071.101 & 1071.102) Please carefully keep this manual for good maintenance. Caution Be sure the door opener is far away from moisture, vibration, and

More information

BARRY BARRIER GATE AUTOMATION

BARRY BARRIER GATE AUTOMATION BARRY BARRIER GATE AUTOMATION Installation Manual 1. WARNINGS AND GENERAL SAFETY INSTUCTIONS This manual contains important safety information. An incorrect installation or an improper use may cause serious

More information

BELT Rapid Fold up Door

BELT Rapid Fold up Door BELT Rapid Fold up Door Quick Assembling Guidebook Belt Manualopen Basic Safety Edge 0161 432 6655 sales@indupart.co.uk /indupart /indupart /indupart /company/indupart-ltd Table of Contents Table of contents

More information

Owner s Manual. For SOLAR BOOM GATE. Model: CA-5000 SOLAR

Owner s Manual. For SOLAR BOOM GATE. Model: CA-5000 SOLAR ECA Electronic Engineering Pty. LTD. Australia Tel: 03-95720 535 Fax: 95 720 536 Owner s Manual For SOLAR BOOM GATE Model: CA-5000 SOLAR ( 2009 / Version 1 ) 1 1 Introduction 1.0 Control PCB Wiring INSTALLATION

More information

DKC400Y AC Sliding Gate Installation Manual. Sliding Gate Opener. Model: DKC400Y. Installation Manual WARNING

DKC400Y AC Sliding Gate Installation Manual. Sliding Gate Opener. Model: DKC400Y. Installation Manual WARNING Sliding Gate Opener Model: DKC400Y Installation Manual WARNING Read and thoroughly understand all instructions before installing or operating this automatic gate opener. Failure to do so may cause serious

More information

Table of Contents. General Safety Preparation for Installation Parts List Optional Accessories Part List... 5

Table of Contents. General Safety Preparation for Installation Parts List Optional Accessories Part List... 5 REV 12a Table of Contents General Safety....... 2 Preparation for Installation....... 3 Parts List....... 4 Optional Accessories Part List...... 5 Technical Specifications & Feature...... 5 Installation

More information

Compact Heat Meters. Features. -A Pulsed output. -B M-Bus output. Accessories. UK Sales Tel: International Tel:

Compact Heat Meters. Features. -A Pulsed output. -B M-Bus output. Accessories. UK Sales Tel: International Tel: Compact Heat Meters Features Compact design Simple operation Pulsed output Measures heating or cooling Specification Product Codes Water Meter Temp. range 10 to 90 C Nominal pressure 16bar Installation

More information

Z TECHNICAL INSTRUCTIONS

Z TECHNICAL INSTRUCTIONS ÍNDICE: Z40 2.0 TECHNICAL INSTRUCTIONS 1.- Error list 2.- Replace the control board 3.- Opening the machine 4.- Replace the power board 5.- Dismantling motor and gear box 6.- Assembly of gear box 7.- Pushing

More information

HIGH SPEED SLIDING GATE OPENER

HIGH SPEED SLIDING GATE OPENER HIGH SPEED SLIDING GATE OPENER Model: is1200 + Elsema s Eclipse Control Card with GDS Operator USER MANUAL CONTENTS Section No: Page No: 1 Safety Precautions 3 2 Wiring Requirements 4 3 Installation details

More information

INSTALLATION GUIDE Table of Contents

INSTALLATION GUIDE Table of Contents CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2

More information

Installation Guide Rollerdor RD77 Econ Roller Garage Door

Installation Guide Rollerdor RD77 Econ Roller Garage Door Installation Guide Rollerdor RD77 Econ Roller Garage Door 1 Finished door Rollerdor RD77 Econ Roller Garage Door CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape

More information

Vertical Vinyl Curtain Door

Vertical Vinyl Curtain Door Vertical Vinyl Curtain Door Face Mount Installation Instructions System Overview: Your Aleco Vinyl Vertical Curtain Door is a high quality, high performance flexible door system based on proven components

More information

Gate & Door Controller with LCD and Intelligent Technology

Gate & Door Controller with LCD and Intelligent Technology 2nd Edition Gate & Door Controller with LCD and Intelligent Technology 24Sv1 and 12Sv1 Motor Controllers Setup and Technical information for single motor controller for gates & doors Includes latest Intelligent

More information

D-FORCE1500PV GARAGE DOOR OPENER

D-FORCE1500PV GARAGE DOOR OPENER D-FORCE1500PV GARAGE DOOR OPENER WARNING: IT IS VITAL FOR THE SAFETY OF ALL PERSONS INSTALLING AND USING THIS OPENER TO FOLLOW THE INSTALLATION INSTRUCTIONS AND SAFETY WARNINGS. FAILURE TO COMPLY MAY RESULT

More information

Installation Guide Rollerdor RD55 Econ Roller Garage Door

Installation Guide Rollerdor RD55 Econ Roller Garage Door Installation Guide Rollerdor RD55 Econ Roller Garage Door 1 Finished door Rollerdor RD55 Econ Roller Garage Door CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape

More information

Combined Ventilation Controller RVWS-T-224HA

Combined Ventilation Controller RVWS-T-224HA Combined Ventilation Controller RVWS-T-224HA 8-stage Control for Power/Natural Applications 2 variable speed stages, 2 curtain winch stages, 2 fixed speed ventilation stages, 1 thermo/mister cycle stage

More information

SLIDE NEW CONTROL BOARD

SLIDE NEW CONTROL BOARD GB SLIDE NEW CONTROL BOARD CN1 CN2 3 4 5 FUSE 2 RL2 RL1 FUSE 1 TR2 TR1 TR3 TR4 U 1 JP1 Ld2 CMR 3 4 CN E Ld7 Ld6 Ld5Ld4Ld3 CN3 3 4 5 6 7 8 9 10 11 SW 12 13 14 Ld1 P2 P1 FUSE 1 FUSE 2 TR1 TR2 TR3 TR4 SW.1

More information

Barrier Gate Manual. (DZX2.1 Control Board) (The third version) (Pictures for reference only, the product prevail in kind)

Barrier Gate Manual. (DZX2.1 Control Board) (The third version) (Pictures for reference only, the product prevail in kind) Barrier Gate Manual (DZX2. Control Board) (The third version) (Pictures for reference only, the product prevail in kind) Contents. Brief Introduction... 2. Functions and Features... 3. Technical Data...2

More information

OMATION FOR SLIDING GATES LINESTAR INSTALLATION MANUAL

OMATION FOR SLIDING GATES LINESTAR INSTALLATION MANUAL AUTOMA OMATION FOR SLIDING GATES LINESTAR INSTALLATION MANUAL CONTENTS 1.0 Description of the system parts page 3 1.1 Description of the parties of the group gearmotor page 3 2.0 General characteristics

More information

INSTALLATION M ANUAL

INSTALLATION M ANUAL INSTALLATION MANUAL Table of Contents UL Listings Installing the Warning Sign / Precautions Methods of Installation / Compact Installation Mounting the Secondary Entrapment / Welding Gate Arn Mounting

More information

User Manual. T6 Tachometer. Online: Telephone: P.O. Box St. Petersburg, Florida 33736

User Manual. T6 Tachometer. Online:   Telephone: P.O. Box St. Petersburg, Florida 33736 User Manual T6 Tachometer Online: www.phareselectronics.com Telephone: 727-623-0894 P.O. Box 67251 St. Petersburg, Florida 33736 Table of Contents Overview... 1 Description... 1 Wiring... 1 T6 Tachometer

More information

JBI Docupunch P33 Automatic Punch

JBI Docupunch P33 Automatic Punch JBI Docupunch P33 Automatic Punch Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com TABLE OF CONTENTS SECTION I: INSTALLATION & TESTING: 1) Uncrating, Inspection & removal

More information

TITANO 400V SLIDING GATE OPENER

TITANO 400V SLIDING GATE OPENER TITANO 400V SLIDING GATE OPENER USE AND MAINTENANCE MANUAL V07 /2018 TECHNICAL FEATURES א א א א QK-T3000 QK-T4000 QK-T6000 (VAC) 400 Three Phase א א א א (W) 700 750 1500 א א א א (A) 1,7 2,2 3,7 א א C -30/+70

More information

Induction Power Supplies

Induction Power Supplies Induction Power Supplies 7.5kW; 135 400kHz 480V version (Integral Heat Station) User s Guide Model 7.5-135/400-3-480 SMD Control Brds Rev. D 5/08 Table of Contents 1. Specifications and features...3 2.

More information

BELT Rapid Fold up Door

BELT Rapid Fold up Door BELT Rapid Fold up Door Quick Assembling Guidebook Belt Clear Opening Dimensions more then 5000 x 5000mm Manualopen Easy Safety Edge 0161 432 6655 sales@indupart.co.uk /indupart /indupart /indupart /company/indupart-ltd

More information

Inlet Controller TC5-ITA USER'S MANUAL. M rev. 02 K rev. 00

Inlet Controller TC5-ITA USER'S MANUAL. M rev. 02 K rev. 00 Inlet Controller TC5-ITA USER'S MANUAL M 890-00047 rev. 02 K 895-00458 rev. 00 TABLE OF CONTENTS PRECAUTIONS... 3 FEATURES... 4 LOCATION OF THE CONTROLS... 5 Status Leds...5 Internal Switches...6 INSTALLATION

More information

VELA INDUSTRIAL INSTALLATION MANUAL

VELA INDUSTRIAL INSTALLATION MANUAL GB English VELA INDUSTRIAL INSTALLATION MANUAL BARRIER Mod.: '11701005' 5mt DX; 11701020' 5mt SX; 11701010 6mt DX; 11701025' 6mt SX; 11701015' 7mt DX; 11701030' 7mt SX; 11701035' 7,5mt DX; 11701040 7,5mt

More information

INSTALLATION MANUAL (cod )

INSTALLATION MANUAL (cod ) is a bollard designed for the management of traffic areas, parkings and protection of public and private accesses. It has an hydraulic system is engineered in our factory to achieve minimum noise and maximum

More information

CARE-C Light Curtain Installation Instructions.

CARE-C Light Curtain Installation Instructions. The Next Generation of Freight Elevator Doors www.couriondoors.com CARE-C Light Curtain Installation Instructions For Immediate Help Call 1-800-533-5760 q Install Mounting Brackets If your Gate Guides

More information

Therm-L-Tec Building Systems LLC. Therm-L-Tech. Power Operated Retrofit Kit 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual

Therm-L-Tec Building Systems LLC. Therm-L-Tech. Power Operated Retrofit Kit 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual Therm-L-Tec Building Systems LLC Therm-L-Tech Power Operated Retrofit Kit 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual Rev. A 01/2015 Index Index 1 Electrical Requirements for Therm-L-Tec

More information

RE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW

RE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW Page 1 of 6 3-Phase Panel Mount 86 and 105kW Features: Benefits: 0-10Vdc, 0-5Vdc, 4-20mA or manual via potentiometer control input Over temperature protection with auto reset Enclosed panel mounting Efficient

More information

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Dycon D1532SM EN50131/PD6662 Grade 3, 12V 2A Power Supply Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Tel: +44 (0)1443 471 900 Unit A Cwm Cynon Business Park Mountain

More information

FLÄKTGROUP PM-MOTOR WITH INTEGRATED FC 106 FREQUENCY CONVERTER

FLÄKTGROUP PM-MOTOR WITH INTEGRATED FC 106 FREQUENCY CONVERTER FLÄKTGROUP PM-MOTOR WITH INTEGRATED FC 106 FREQUENCY CONVERTER INSTALLATION AND MAINTENANCE INSTRUCTIONS Risk of electric shock: Motor terminals may still be live if the impeller is rotating, even when

More information

Wheel Products. WP8300 Operators Manual Rev: 910

Wheel Products. WP8300 Operators Manual Rev: 910 Wheel Products by WP8300 Operators Manual Rev: 910 Table of Contents Warranty Page 1 1. General Page 2 General Safety Regulations Page 2 Field of Application Page 2 Overall Dimensions Page 2 Technical

More information

USER MANUAL MPS 1-5KW SERIES

USER MANUAL MPS 1-5KW SERIES USER MANUAL MPS 1-5KW SERIES Low Series Frequency Solar and Wind Power Charging Inverter CONTENTS 1 WWW.NEXTGENNRG.COM 1. Introduction... 3 2. Profile Structure 4 2.1. Working Principle 4 2.2.Product Features..5

More information

USER MANUAL PAR56 LED PAR CANS

USER MANUAL PAR56 LED PAR CANS USER MANUAL PAR56 LED PAR CANS 153.766 / 153.769 Slimline PAR64 LED Par can For indoor use only Caution! Please read this manual carefully before operating! Damage caused by misuse is not covered by the

More information

AUTOMATIC CONTROL ROLLING DOOR OPENER

AUTOMATIC CONTROL ROLLING DOOR OPENER AUTOMATIC CONTROL ROLLING DOOR OPENER INSTALLATION INSTRUCTION AUTOMATIC OBSTRUCT PHOTOELECTRIC BEAM ROLLING CODE SYSTEM AUTO CLOSE DOOR ANTI-THEFT SYSTEM INSTALLATION INSTRUCTION AND RDO OWNERS MANUAL

More information

Power Operated Retrofit Kit for Manual Door 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual

Power Operated Retrofit Kit for Manual Door 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual Therm-L-Tec Building Systems LLC Therm-L-Tech Power Operated Retrofit Kit for Manual Door 230 VAC or 440/480 VAC 50/60 Hz Installation and Setup Manual Rev. A 10/2014 Index Index 1 Electrical Requirements

More information

Snapshot LX5 USER MANUAL. OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle

Snapshot LX5 USER MANUAL. OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle LX5 Snapshot OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle USER MANUAL Chauvet, 5200 NW 108th Avenue, Sunrise, FL 33351 U.S.A.

More information

TECHNICAL DATA HYDRAULIC UNIT

TECHNICAL DATA HYDRAULIC UNIT GB INSTRUCTIONS MANUAL RISING BOLLARD OIL-HYDRAULIC AUTOMATION COMPONENTS strabuc 918 RELEASE KEY PLUG FOR RELEASE HOLE BOLLARD COVER 12 V WARNING LIGHTS REFLECTORS COMPLETELY RETRACTABLE POST WITH ELECTROPHORESIS

More information

User s Manual. Automatic Switch-Mode Battery Charger

User s Manual. Automatic Switch-Mode Battery Charger User s Manual Automatic Switch-Mode Battery Charger IMPORTANT Read, understand, and follow these safety rules and operating instructions before using this battery charger. Only authorized and trained service

More information

DKG-114 MANUAL AND REMOTE START UNIT

DKG-114 MANUAL AND REMOTE START UNIT DKG-114 MANUAL AND REMOTE START UNIT FEATURES Both manual and remote controlled engine starting and stopping, Automatic shutdown on fault condition, Optional cooldown cycle on remote start operation, Optional

More information

Installation and Operation Back-UPS BX550CI-CN

Installation and Operation Back-UPS BX550CI-CN Installation and Operation Back-UPS BX550CI-CN Safety and General Information This unit is intended for indoor use only. Do not operate this unit in direct sunlight, in contact with fluids, or where there

More information

Furnace Web Site FAQs. Pro Press 100 / Pro 100 / Pro 100 plus. Lift. Belt Noise

Furnace Web Site FAQs. Pro Press 100 / Pro 100 / Pro 100 plus. Lift. Belt Noise Furnace Web Site FAQs Pro Press 100 / Pro 100 / Pro 100 plus Lift Belt Noise A Worn belt Over time the belt may become dry or worn due to heat and travel. Replace the belt Tight If the belt was recently

More information

Pure Sine Wave Inverter GP-HS1500. Owner s Manual

Pure Sine Wave Inverter GP-HS1500. Owner s Manual Pure Sine Wave Inverter GP-HS1500 Owner s Manual 2 Table of Contents Introduction 3 Specifications 4 Name and Main Function 5 Installation 7 Operation 9 Operating Limits 13 Troubleshooting 13 Maintenance

More information

LIFTMASTER MAGIC BUTTON FS10 & LPK5 FAST SLIDER

LIFTMASTER MAGIC BUTTON FS10 & LPK5 FAST SLIDER R MAGIC BUTTON FS0 & LPK5 FAST SLIDER OPERATORS MANUAL FEATURES High speed -800mm/second Corrosion resistant - Hot dip galvanised base with stainless steel cover Speed flexibility - Slow start / slow stop

More information

PowerOhm Installation Manual for BM R Series Braking Modules

PowerOhm Installation Manual for BM R Series Braking Modules PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

USERS GUIDE LO-21U LOCKOUT RELAY

USERS GUIDE LO-21U LOCKOUT RELAY USERS GUIDE LO-21U LOCKOUT RELAY PRODUCT DESCRIPTION The LO-21U (PN: 10LO21U) is a micro-processed lock out module designed to operate on swing door applications with BEA s Bodyguard or DK-12 overhead

More information

Instruction Manual for the. E-SL 450 Series

Instruction Manual for the. E-SL 450 Series Instruction Manual for the E-SL 450 Series Estate Slide Summary of Functions The Estate Slide is only to be used for vehicular Slide gates in a Class I setting. Class I: A vehicular gate opener (or system)

More information

PowerOhm Installation Manual for BM R Series Braking Modules

PowerOhm Installation Manual for BM R Series Braking Modules PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

Datasheet PDCSY-MW-CHM. Technical Overview. Features. Product warranty and total quality commitment. General Information.

Datasheet PDCSY-MW-CHM. Technical Overview. Features. Product warranty and total quality commitment. General Information. Datasheet Compact Heat Meters Technical Overview Heat energy is calculated by using a matched pair of high accuracy sensors to measure the difference between the forward and flow temperatures. The amount

More information

D Vers. 03 ELECTROMECHANICAL AUTOMATION FOR SWING GATES

D Vers. 03 ELECTROMECHANICAL AUTOMATION FOR SWING GATES E5 D811007 15-09-99 Vers. 03 ELECTROMECHANICAL AUTOMATION FOR SWING GATES 122 This product complies with recognised technical standards and safety regulations. We declare that this product is in conformity

More information

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location

More information

Back-Up Sensor System

Back-Up Sensor System Back-Up Sensor System Model No.: PKC0RE Owner s Manual and Warranty Information OFF ON 0.4m/1.3ft 0.6m/2.0ft 1.0m/3.3ft 1.2m/4.0ft 1.5m/5.0ft LEFT RIGHT Read these instructions completely before using

More information

INSTRUCTION MANUAL_1219_ENGLISH SUPER ELF X3. Operating Instructions for DORNIER looms. Robustness Reliability Quality Productivity Versatility

INSTRUCTION MANUAL_1219_ENGLISH SUPER ELF X3. Operating Instructions for DORNIER looms. Robustness Reliability Quality Productivity Versatility INSTRUCTION MANUAL_1219_ENGLISH SUPER ELF X3 Operating Instructions for DORNIER looms Robustness Reliability Quality Productivity Versatility WARNING! - Condensation could form on the Weft Feeder when

More information

SECEUROGLIDE ROLLER GARAGE DOORS, SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS

SECEUROGLIDE ROLLER GARAGE DOORS, SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS Operating & Maintenance Instructions SECEUROGLIDE ROLLER GARAGE DOORS, July 2007 Issue 4 SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS Page 1. General Instructions 2 2. Operating

More information

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY 00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement

More information

Covers All 430, 440, 441 and CJ Series Advanced Security Systems.

Covers All 430, 440, 441 and CJ Series Advanced Security Systems. INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with

More information

TECHNICAL MANUAL AND ELECTRONICAL MODULE REGULATION VVVF-4 +

TECHNICAL MANUAL AND ELECTRONICAL MODULE REGULATION VVVF-4 + TECHNICAL MANUAL AND ELECTRONICAL MODULE REGULATION VVVF-4 + 8 CABIN DOORS DESCRIPTION OF SWITCHES The unit may be programmed using the DIL switches on the front of the unit. If any change is made to any

More information

Observe all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning.

Observe all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning. Introduction OPERATING INSTRUCTIONS: MCD REMOTE OPERATOR Order Codes: 175G94 (for MCD 2) 175G361 + 175G9 (for MCD 5) 175G361 (for MCD 3) 1. Introduction 1.1. Important User Information Observe all necessary

More information

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL INSTALLATION INSTRUCTIONS AND OPERATION MANUAL Commercial and Industrial Fire Door Operator Logic Control Restricted Duty Fire Door Operators IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk

More information

3D PRINTER USER MANUAL

3D PRINTER USER MANUAL 3D PRINTER USER MANUAL Table of contents page: 1. Introduction 2. Table of contents 3. Basic informations 4. General information 5. Glossary 6. Starter pack s content 7. Technical parameters 8. Device

More information

L /2010 rev 5 MATRIX MATRIX-RE CP.BULL CP.BULL-RI UNIONE NAZIONALE COSTRUTTORI AUTOMATISMI PER CANCELLI, PORTE SERRANDE ED AFFINI

L /2010 rev 5 MATRIX MATRIX-RE CP.BULL CP.BULL-RI UNIONE NAZIONALE COSTRUTTORI AUTOMATISMI PER CANCELLI, PORTE SERRANDE ED AFFINI L8542124 07/2010 rev 5 MATRIX MATRIX-RE CP.BULL CP.BULL-RI UNIONE NAZIONALE COSTRUTTORI AUTOMATISMI PER CANCELLI, PORTE SERRANDE ED AFFINI MATRIX / MATRIX-RE / CP.BULL / CP.BULL-RI MATRIX > BULL10M SC/15M

More information

EB Conveyor Maintenance Guide

EB Conveyor Maintenance Guide EB Conveyor Maintenance Guide EN-0037 Rev A EB Conveyor Maintenance Guide www.qdraw.com Table of Contents Overview Page 3 Exploded View Of A Standard EB Conveyor Page 4 Preventative Maintenance Page 5

More information

YG101 SWING GATE OPENER OWNER S MANUAL

YG101 SWING GATE OPENER OWNER S MANUAL YG101 SWING GATE OPENER OWNER S MANUAL IMPORTANT SAFTEY INFORMATION Installing the YG101 Gate Opener requires wiring of standard 110V electrical lines. This should only be performed by a trained technician.

More information

Model 1:8 Beast-ZTWSS120A 1:8 Beast-ZTWSS150A. PN#Model Cont.Current 120A 150A. Burst Current 760A 1080A

Model 1:8 Beast-ZTWSS120A 1:8 Beast-ZTWSS150A. PN#Model Cont.Current 120A 150A. Burst Current 760A 1080A Alien Power System BEAST Series Sensored/Sensorless Brushless ESC for 1:8 scale Car or Truck Thank you for purchasing the Alien Power System Brushless Electronic Speed Controller (ESC). The Alien Power

More information

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY 0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod

More information

Read Chapter 8 Servicing Machine in the Manual for general guidelines

Read Chapter 8 Servicing Machine in the Manual for general guidelines Page 1 of 6 Read Chapter 8 Servicing Machine in the Manual for general guidelines The PlasmaCAM will not work on a GFI circuit. Earth ground the grates of the PlasmaCAM. Computer Configuration A. PlasmaCAM

More information

NB NB 1511 NB NB 4031 TRUE ON-LINE DOUBLE CONVERSION UPS

NB NB 1511 NB NB 4031 TRUE ON-LINE DOUBLE CONVERSION UPS NB 0811 - NB 1511 NB 0831 - NB 4031 TRUE ON-LINE DOUBLE CONVERSION UPS LEN.MAN.UPS.069 Rev.2.00/2002 CONTENTS Safety Instructions 1 Introduction 3 2.1 FEATURE 3 2.2 UPS modules 4 How the UPS works 5 3.1

More information

5600 Series Power Operator Installation and Instruction Manual

5600 Series Power Operator Installation and Instruction Manual 5600 Series Power Operator Installation and Instruction Manual 80-956-000-00 (08-) 5 ASSA ABLOY 6 Item No. Description Motor (5600M) Cover (5600COV) Control Inverter (5600IN) Power Supply VDC (5600PS)

More information

Installing the gate post bracket with the cardboard arm template

Installing the gate post bracket with the cardboard arm template ......... Installing the gate post bracket with the cardboard arm template... Installing gate posts brackets and arms for Push-to-Open or Pull-to-Open gates... Connection of Power Source 240Vac or Solar...

More information

USER MANUAL LUX-LD30W LED MOVING HEAD

USER MANUAL LUX-LD30W LED MOVING HEAD USER MANUAL LUX-LD30W LED MOVING HEAD LUX-LD30W LED MOVING HEAD For indoor use only Caution! Please read this manual carefully before operating! Damage caused by misuse is not covered by the warranty!

More information

1999 Mercury Cougar ACCESSORIES & EQUIPMENT' 'Passive Anti-Theft Systems - Cougar 1999 ACCESSORIES & EQUIPMENT

1999 Mercury Cougar ACCESSORIES & EQUIPMENT' 'Passive Anti-Theft Systems - Cougar 1999 ACCESSORIES & EQUIPMENT DESCRIPTION 1999 ACCESSORIES & EQUIPMENT Passive Anti-Theft Systems - Cougar Passive Anti-Theft System (PATS) is available on some vehicles. The system is passive in that it does not require any activity

More information

FM SECURITY AND REMOTE START SYSTEM

FM SECURITY AND REMOTE START SYSTEM FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with

More information

BOXER KING 5600/5600R TRUCK TYRE CHANGER

BOXER KING 5600/5600R TRUCK TYRE CHANGER Author Stefano Muzzioli BOXER KING 5600/5600R TRUCK TYRE CHANGER SERVICE MANUAL 1 UPDATING GUIDE: Release B of 02/04/2010 Removed 50 or 60 Hz At page 49 2 TABLE OF CONTENTS 1.0 Introduction Pag. 5 2.0

More information

Sliding Gate Operator User's Manual

Sliding Gate Operator User's Manual Sliding Gate Operator User's Manual SL600AC. Products introduction Please read the instructions carefully before proceeding. MCU is supplied to control the gate operator. Keypad / single button interface.

More information

Installing the gate post bracket with the cardboard arm template

Installing the gate post bracket with the cardboard arm template ......... Installing the gate post bracket with the cardboard arm template... Installing gate posts brackets and arms for Push-to-Open or Pull-to-Open gates... Connection of Power Source 240Vac or Solar...

More information

Delta Secure Spiroll 40 High Speed Security Door. Product Data Sheet 4 / 7

Delta Secure Spiroll 40 High Speed Security Door. Product Data Sheet 4 / 7 Product Description Our superbly engineered Delta Secure Spiroll 40 provides high-speed operation with security, using proven reliable technology to achieve long tem solutions for almost any application

More information

Parker AC10 Frequency Inverter (to 22kW) Easy Start Guide

Parker AC10 Frequency Inverter (to 22kW) Easy Start Guide Parker AC10 Frequency Inverter (to 22kW) Easy Start Guide CAUTION: 1)Do not re-set while the motor is rotating 2)Perform parts replacement after discharge is finished 3)Do not connect output terminals

More information

PowerOhm Installation Manual for LG ATV Series Braking Modules

PowerOhm Installation Manual for LG ATV Series Braking Modules PowerOhm Installation Manual for LG ATV Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

EC MACHINE DIRECTIVE COMPLIANCE DECLARATION

EC MACHINE DIRECTIVE COMPLIANCE DECLARATION EC MACHINE DIRECTIVE COMPLIANCE DECLARATION (DIRECTIVE 89/392 EEC, APPENDIX II, PART B) Manufacturer: FAAC S.p.A. Address: Via Benini, 1 40069 - Zola Predosa BOLOGNA - ITALY Hereby declares that: the 770

More information

IGLOO IGLOO EASY INSTRUCTION MANUAL

IGLOO IGLOO EASY INSTRUCTION MANUAL ENGLISH EASY C695 C698 INSTRUCTION MANUAL Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky range, has

More information

Technical Installation and Service Manual RollSeal 1733 County Road 68 Bremen, Alabama 35033

Technical Installation and Service Manual RollSeal 1733 County Road 68 Bremen, Alabama 35033 Technical Installation and Service Manual RollSeal 1733 County Road 68 Bremen, Alabama 35033 4801-5159 rev. 05/14 Technical Installation and Service Manual Page 1 of 26 1. Ratings and Specifications Motor

More information

VECTRIX VX-2 SERVICE MANUAL. Version 1.0/May 2011 VECTRIX, LLC

VECTRIX VX-2 SERVICE MANUAL.   Version 1.0/May 2011 VECTRIX, LLC www.vectrix.com CONTENTS SECTION A: Tools 1 Tools Needed SECTION B: Mechanical Parts 1 Front Fairing 2 Front Console Cover 3 Speedometer Cover 4 Front Vertical Panel Cover-Lower 5 Front Vertical Panel

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2581 INSTALLATION INSTRUCTIONS 08-15 IMPORTANT PLEASE DON T HURT YOURSELF, THE KIT, OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. SAFE INSTALLATION Please take all safety precautions

More information

Informational Distribution List:

Informational Distribution List: Technical Bulletin 2017 Southern Technologies Corporation (STC). All rights reserved. Bulletin Number: TB-2017198-BW01 Date Published: 07/17/2017 Summary: Instructions for mounting, aligning and setting

More information

Power Distribution System User s Manual. Model: PDS-100

Power Distribution System User s Manual. Model: PDS-100 Power Distribution System User s Manual Model: PDS-0 Section Page Product Overview... 1 I) General Information... 2 II) Important Safety Information... 2 III) Installation... 3 A) Materials Provided...

More information