hydraulics K5 K12 K17 K25

Transcription

1 hydraulics K5 K12 K17 K25 J22

2 HYDRAULICS Care & Maintenance Hydraulic tools and equipment must be inspected before each use to identify signs of wear, cracks, nicks, abrasions, leaking, damaged or missing parts. Any item found not to be in good working order should replaced or repaired immediately. Always read the instruction manuals prior to use and follow the recommended practices. Failure to read and fully understand these warnings can lead to property damage and/or severe personal injury. Always use correct PPE. Ensure that you fully comply with all safe operation guidelines required by your employer. Consider the following recommendations for your hydraulic hoses and systems: Use male fittings on hoses and female fittings on equipment, male fittings are easier to clean Never kink or intentionally bend, pull or strain hydraulic hoses Always wipe fittings clean before connecting Always ensure dust caps and plugs are fitted on hoses when not in use Store hoses out of sunlight, hoses left in direct sunlight will degrade. Pressures will also be generated when oil expands in hose making initial connection difficult Hoses should not be banged to release pressure, operating tool or hydraulic system can relieve pressure Do not use hydraulic hoses for lifting Replace hydraulic hoses at set time periods regardless of use, two years is a suggested maximum Refer to page K16 for Low Pressure Hoses Refer to page K24 for High Pressure Hoses Refer to page K33-K34 for Coupler Plugs and Dust Caps Servicing Utilities and contractors make large investments in tools and equipment each year. Significant resources are allocated to asset maintenance programs while tools and equipment are often overlooked for scheduled servicing. Scheduled servicing extends the life of tools, minimises unplanned downtime and reduces tool lifetime costs. Servicing tools and equipment extends the useable life of the tool by replacing worn components before a failure or fault occurs. Replacing a low cost seal on a hydraulic tool could be the difference between getting a job done and costly delays. Repairing damaged tools will likely be more costly than undertaking regular scheduled service. A regular service schedule allows you to plan and manage downtime and reduces the likelihood of unplanned downtime as a result of tool failure. Service work can be carried out at a time when the tool is not in use. TEN offers loan tools where available. Not servicing tools and equipment increases safety risks. K1 Quality Electrical Equipment for Generation, Transmission & Distribution

3 BATTERY POWERED CRIMPERS Mini Battery Tool up to 5 Tonne Part No: EK Series Lightweight and ergonomic one handed operation High performance NiMH battery technology Multifunction LED indicates battery and maintenance feature Interchangeable dies or heads, sold separately Quick crimp cycle Rotating head Automatic retraction on completion of crimp cycle Manual retraction button does not rely on battery Environmentally friendly biodegradable hydraulic oil Part No EK354AU EK1550GAU EK1550AU EKP1AU Crimp Force (kn/tonne) No of Crimps per charge 35/3.5 13/1.3 13/1.3 10/ mm² 10mm² 10mm² 10mm² Head Type Flip Top Side Scissor C Removable C Head Rotation ( ) Stroke (mm) Max Crimp (mm2) Cu Al 70 - No No Crimp Style (Dies Sold Separately) Die or Head Type 1 Specific Features Heads Interchangeable with Hand Tool (Sold Separately) Kit Contents Plastic Case, Tool, Charger 240VAC, 2 x Batteries Spare Battery RAM2* RAM2* RAM2* RAM2* Battery Voltage (DC) Battery Amp-hour (Ah) Spare Charger (240VAC) LG4F LG4F LG4F LG4F Weight of Tool (kg) * RAM3 Battery also available (3.0Ah), refer to pages K11-K12 for accessories 1 Contact TEN for further specifications ASK TEN K2

4 Mini Battery Tool up to 5 Tonne Part No: EK Series Lightweight and ergonomic one handed operation Audible and visual fault signal notifies of incomplete crimp pressure or crimp cycle interruption Genuine Makita high performance Lithium-Ion battery Quick battery charge time - 15 minutes Multifunction LED indicates battery and maintenance feature Interchangeable dies or heads, sold separately Quick crimp cycle Rotating head Automatic retraction on completion of crimp cycle Manual retraction button does not rely on battery LED light facing crimp jaw illuminates dark work areas Environmentally friendly biodegradable hydraulic oil ABC Part No EK425LAU EK505LAU EK5018LA Crimp Force (kn/tonne) 50/5 50/5 50/5 No of Crimps per charge 70mm² - 150mm² Head Type Scissor Flip Top Flip Top Head Rotation ( ) Stroke (mm) Max Crimp (mm2) Cu Al ACSR 185 No No Crimp Style (Dies Sold Separately) Die Type Specific Features Kit Contents Certified for ABC Crimps, 3 ABC Dies Included Plastic Case, Tool, 2 x Crimp Head (CJD3BG & CJ22), 3 x ABC Dies & 1 x Cutting Die, Charger 240VAC, 2 x Batteries - - Plastic Case, Tool, Charger 240VAC, 2 x Batteries Spare Battery RAL1* RAL1* RAL1* Battery Voltage (DC) Battery Amp-hour (Ah) Spare Charger (240VAC) LGL1 LGL1 LGL1 Weight of Tool (kg) * RAL2 Battery 3.0Ah & NG2 Power Pack also available, refer to pages K11-K12 for accessories 1 Refer to page K12 for Dies, 2 Contact TEN for further specifications K3 Quality Electrical Equipment for Generation, Transmission & Distribution

5 Ultra 5-6 Tonne Part No: EK Series Lightweight and ergonomic one handed operation Audible and visual fault signal notifies of incomplete crimp pressure or crimp cycle interruption Genuine Makita high performance Lithium-Ion battery Quick battery charge time - 22 minutes Multifunction LED indicates battery and maintenance feature Quick crimp cycle Rotating head Automatic retraction on completion of crimp cycle Manual retraction button does not rely on battery LED light facing crimp jaw illuminates dark work areas Balanced centre of gravity Environmentally friendly biodegradable hydraulic oil Automatic retraction stop Part No EK6022LAU EK60VPLAU EK60VPFTLAU Crimp Force (kn/tonne) 60/6.0 55/5.5 55/5.5 No of Crimps (Per charge) 150mm² 150mm² 150mm² Head Type Flip Top Indent Open C Indent Flip Top Head Rotation ( ) Stroke (mm) Max Crimp (mm2) Cu Al Die Type Dieless Specific Features ARS Automatic Retraction Stop (Multiple Crimping) ARS Automatic Retraction Stop (Multiple Crimping) Dieless ARS Automatic Retraction Stop (Multiple Crimping) Dieless Kit Contents Plastic Case, Tool, Charger 240VAC, 2 Batteries, Shoulder Strap Spare Battery RAL2* RAL2* RAL2* Battery Voltage (DC) Battery Amp-hour (Ah) Spare Charger (240VAC) LGL1 LGL1 LGL1 Weight of Tool (kg) * NG2 - Mains adaptor 240VAC also available, refer to pages K11-K12 for accessories ASK TEN K4

6 Ultra Plus 12 Tonne Part No: EK Series Lightweight and ergonomic design Audible and visual fault signal notifies of incomplete crimp pressure or crimp cycle interruption Genuine Makita high performance Lithium-Ion battery Quick battery charge time - 22 minutes Multifunction LED indicates battery and maintenance feature Quick crimp cycle Rotating Head Automatic retraction on completion of crimp cycle Automatic retraction stop for multiple crimping applications Manual retraction button does not rely on battery LED light facing crimp jaw illuminates dark work areas Balanced centre of gravity Environmentally friendly biodegradable hydraulic oil Part No EK12042LAU EK120ULAU EK120IDLAU Crimp Force (kn/tonne) 120/12 120/12 120/12 # of Crimps per charge 150mm² 150mm² 150mm² Head Type Open C U Indent Fliptop Head Rotation ( ) Stroke (mm) Max Crimp (mm2) Cu Al Jaw Opening (mm) Die Type Dieless Kit Contents Plastic Case, Tool, Charger 240VAC, 2 x Batteries, Shoulder Strap Spare Battery RAL2* RAL2* RAL2* Battery Voltage (DC) Battery Amp-hour (Ah) Spare Charger (240VAC) LGL1 LGL1 LGL1 Weight of Tool (kg) * NG2 - Mains adaptor 240VAC also available, refer to pages K11-K12 for accessories 1 25mm Jaw model also available (EK12025LAU) No Pinch Point EK12042 has no ram pinch point LED light illuminates work space Heavy Duty Makita Li-Ion Batteries K5 Quality Electrical Equipment for Generation, Transmission & Distribution

7 BATTERY POWERED CUTTERS Mini up to 32mm OD Part No: EB & ES Series Pressure relief valve prevents overloading tool if incorrect or oversized material is inserted Lightweight, ergonomic one handed operation High performance NiMH battery technology Multifunction LED indicates battery and maintenance feature Automatic retraction on completion of cut cycle Manual retraction button does not rely on battery Environmentally friendly biodegradable hydraulic oil Rotating Head ACSR Part No EBS12AU ES20AU ES32AU Cut Force (kn/tonne) 3.5/3.5 25/2.5 13/1.3 No of Cuts per charge 60 ACSR 120/20 240mm² Head Type Open C Scissor Scissor Head Rotation ( ) Max Cut OD (mm) Cu P P P Al P P P ACSR X P X Steel Rope P P X Cable tray & Catenary Wire P X X Bolts P P X Other Models Available Kit Contents EBS8 Max 8mm OD, 1.3kN Cut Force, 300 5mm Plastic Case, Tool, Charger 240VAC, 2 x Batteries * RAM3 also available 3.0Ah, refer to pages K11-K12 for accessories - Plastic Case, Tool, Charger 240VAC, 2 x Batteries ES32F Max 32mm OD, Specially Designed for Fine Copper Cables Plastic Case, Tool, Charger 240VAC, 2 x Batteries Spare Battery RAM2* RAM2* RAM2* Battery Voltage (DC) Battery Amp-hour (Ah) Spare Charger (240VAC) LG4F LG4F LG4F Weight of Tool (kg) ASK TEN K6

8 Ratchet up to 82mm OD Part No: ES Series Lightweight, ergonomic handed operation Compact design allows use in confined spaces Heavy duty blades for clean cuts and long life Large blade opening High performance Ni-Cd battery technology Easy operation of forward and reverse Guillotine up to 25mm OD Part No: ESG Series Lightweight, ergonomic one hand operation Audible and visual fault signals Genuine Makita Lithium-Ion battery Quick battery charge time - 15 minutes Multifunction LED indicates battery and maintenance feature Quick cut cycle Rotating head Automatic retraction on cut completion Manual retraction does not rely on battery LED light illuminates dark work areas Environmentally friendly biodegradable hydraulic oil Part No ES2522AU ES8522AU ES100022AU ESG25LAU No of Cuts per charge 17.37mm OD ACSR 1800 Pair 400mm² 500mm² Cu 10mm OD Steel Cut Time (sec) Head Type Ratchet Ratchet Ratchet Guillotine Head Rotation ( ) Jaw Opening (mm) Max Cut OD (mm) Cu P X P 25 Al P X P 25 ACSR 20 X X 25 Specific Features ACSR Communications - ACSR & Steel Length (mm) Kit Contents Plastic Case, Tool, Charger 240VAC, 2 x Batteries Plastic Case, Tool, Charger 240VAC, 2 x Batteries Plastic Case, Tool, Charger 240VAC, 2 x Batteries Plastic Case, Tool, Charger 240VAC, 2 x Batteries Spare Battery RAL1 Battery Voltage (DC) Battery Amp-hour (Ah) * Spare Charger (240VAC) LGL1 Weight of Tool (kg) * RAL2 3.0Ah Battery also available K7 Quality Electrical Equipment for Generation, Transmission & Distribution

9 Ultra up to 50mm OD Part No: ESG Series Lightweight, ergonomic design Audible and visual fault signal notifies of incomplete crimp pressure or crimp cycle interruption Genuine Makita high performance Lithium-Ion battery Quick battery charge time - 22 minutes Multifunction LED indicates battery and maintenance feature Automatic retraction on completion of cut cycle Automatic retraction stop for multiple cutting applications Manual retraction button does not rely on battery LED light facing crimp jaw illuminates dark work areas Balanced centre of gravity Environmentally friendly biodegradable hydraulic oil Rotating Head ESG45LAU ACSR & Steel ESG50LAU ESG85LAU ESG105LAU ES85LAU ES105LAU Part No ESG45LAU ESG50LAU ES85LAU ES105LAU ESG85LAU ESG105LAU Cut Force (kn/ton) 60/6 50/5 30/3 74/7.4 60/6 120/12 No of Cuts per charge ACSR 570/40 4x120mm² 4x240mm² 4x240mm² 4x240mm² 4x240mm² Head Type Guillotine Guillotine Scissor Scissor Guillotine Guillotine Head Rotation ( ) Max Cut OD (mm) Cu P P P P P P Al P P P P P P ACSR P X X X X X Steel 20 X X X X X Armoured P Light Al/Cu Light Al/Cu Light Al/Cu Light Al/Cu P Specific Features - - Kit Contents Side Screw Handle Side Screw Handle Plastic Case, Tool, Charger 240VAC, 2 x Batteries Folding Handle Folding Handle Spare Battery RAL2* RAL2* RAL2* RAL2* RAL2* RAL2* Battery Voltage (DC) Battery Amp-hour (Ah) Spare Charger (240VAC) LGL1 LGL1 LGL1 LGL1 LGL1 LGL1 Weight of Tool (kg) * NG2 - Mains adaptor 240VAC also available, refer to pages K11-K12 for accessories ASK TEN K8

10 Multi Cut & Crimp Part No: EKUNV Series Lightweight, ergonomic design Audible and visual fault signal notifies of incomplete crimp pressure or crimp/cut cycle interruption Genuine Makita high performance Lithium-Ion battery Quick battery charge time - 22 minutes Multifunction LED indicates battery and maintenance feature Automatic retraction on completion of cycle Automatic retraction stop for multiple applications Manual retraction button does not rely on battery LED light facing crimp jaw illuminates dark work areas Balanced centre of gravity Environmentally friendly biodegradable hydraulic oil Rotating head Crimp, cut and punch with one tool Part No EK60UNVLCCAU EK120UNVLCCAU Cut/Crimp Force (kn/ton) 60/6 108/12 No of Crimps per charge 150mm² Cu 150mm² Cu Head Type Flip Top Flip Top Head Rotation ( ) Max Cut OD (mm) Cu P P Al P P ACSR P P Steel Rod Guy Wire Armoured P P Max Crimp (mm2) Cu Al Specific Features Kit Contents Multi-functional - cuts, crimps & punches (punches & accessories sold separately - see next page) Plastic Case, Tool, 6 Ton C Die Adaptor, Cutter Blade, Charger 240VAC, 2 x Batteries Plastic Case, Tool, 12 Ton C Die Adaptor, Cutter Blade, Charger 240VAC, 2 x Batteries Spare Battery RAL2* RAL2* Battery Voltage (DC) Battery Amp-hour (Ah) Spare Charger (240VAC) LGL1 LGL1 Weight of Tool (kg) * NG2 - Mains adaptor 240VAC also available, refer to pages K11-K12 for accessories K9 Quality Electrical Equipment for Generation, Transmission & Distribution

11 Multi Spares & Accessories Part No: Various Other accessories available, contact TEN for more details Suit Tool EK60UNVCCAU EK120UNVCCAU Cutter Blades UCACSR UCACSR Die Adaptor¹ UA22 UA12T Punch Adaptor UA6P UA12P Punches * * Punch Accessories * * Din Rail Cutter UCD3515 (35x15mm) UCD3515 (35x15mm) Din Rail Puncher UCD3215 (32x15x9mm) UCD3215 (32x15x9mm) Threaded Rod Cutter Blades UCM3575 (35x7.5mm) UCM3575 (35x7.5mm) Busbar Cutter UCF UCF ¹ Die adaptors for Cembre, Greenlee and Burndy tools also available * Various sizes available upon request Safety Cutter, Remote Cable Cutting Part No: ESSGL Series Kit used for cutting de-energised or possibly live underground cables Remote operation with earth stake included Certified non-conductive hose tested at 75kV/300mm Lightweight and ergonomic design Audible and visual fault signal notifies of incomplete cut cycle or interruption Genuine Makita high performance Li-Ion battery Quick battery charge time - 22 minutes Multifunction LED indicates battery and maintenance feature Manual retraction button, does not rely on battery Balanced centre of gravity design Pressure gauge on tool hose connection Environmentally friendly biodegradable hydraulic oil Not interchangeable with any other Klauke or competitor tools Scope of Kit Supply 1 x ESSG Trigger Power Unit 1 x SSK Cutting Head 1 x Earth Stake with Lead 2 x RAL2 Batteries 1 x Carry Case Part No Cutting Head Type Trigger Tool of Head Unit Cuts Cable Type Max OD (mm) ESSGSSKG85AU Guillotine Cu/Al 85 ESSGSSK65AU Scissor Cu/Al 65 ESSGSSK105AU Scissor Cu/Al 105 NG2 - Mains adaptor 240VAC also available, refer to pages K11-K12 for accessories ASK TEN K10

12 BATTERIES, CHARGERS & ACCESSORIES Tool Strap Part No: RH1819 Quality Webbing tool strap with clip Klauke Electronic Reader for Battery Hydraulic Tools Part No: PGA1 Used only on Klauke Generation Safety Plus tools Allows Important Quality Assurance checking of pressure, faults, total crimp or cuts, crimps or cuts since last service and many other details. Readout of tool details through USB connection to PC or Laptop Part No Connection Type System Requirements Minimum Weight (kg) PGA1 USB 2.0 Windows XP 0.3 Batteries Part No: Various Part No RAM2 RAM3 RA5 RAL1 RAL Cells Ni-MH Ni-MH Ni-MH Li-Ion Li-Ion Ni-Cd Voltage (DC) Amp Hour (Ah) Weight (kg) Chargers Part No: Various Part No LG4FAU LG5AU LGLAU LGM5AU LGL2AU Type Ni-Cd & Ni-MH Ni-Cd & Ni-MH Li-Ion Ni-Cd & Ni-MH Li-Ion Ni-Cd Battery Approx Charge Time (min) RAM2, RAM3, RA RAM2, RAM3, RA (Ni-Cd) (Ni-MH) RAL1, RAL2 15 (RAL1) 22 (RAL2) RAM2, RAM3, RA (Ni-Cd) 75 (Ni-MH) RAL1, RAL (RAL1) 22 (RAL2) Input Voltage 240VAC 240VAC 240VAC 12-24VDC 12-24VDC 240VAC Weight (kg) K11 Quality Electrical Equipment for Generation, Transmission & Distribution

13 Power Packs 240VAC Part No: Various Heavy duty continuous usage with built in thermal overload protection Works from most inverters Part No NG1-230AU NG2-230AU Input Voltage (VAC) Lead Length (m) 4 5 NG2-230AU Replaces Battery Type RA RAL Weight (kg) NG1-230AU CRIMPING DIES 6 Tonne Dies Part No: Various Crimping dies to suit 6 Tonne hydraulic battery and hand crimpers (Klauke EK425, EK60UNVCC and HK6022) Commonly referred to as C or U type dies Dies colour coded for easy identification Part No Type Conductor Type (mm 2 ) A/F (mm) Width (mm) Finish K06-A-9.0 Aluminium Silver K06-A-13.2 Aluminium Silver K06-A-17.3 Aluminium Silver K06-A-22.0 Aluminium Silver K06-C-6.3 Copper Gold K06-C-7.7 Copper Gold K06-C-9.2 Copper Gold K06-C-10.4 Copper Gold K06-C-11.5 Copper Gold K06-C-14.2 Copper Gold K06-C-16.5 Copper Gold K06-C-18.3 Copper Gold K06-C-20.0 Copper Gold E22140 ABC Silver E22173 ABC Silver E22215 ABC Silver Special die sizes available upon request Cutting...Crimping... The Power of Partnership ASK TEN K12

14 12 Tonne Dies Part No: K12 Series Crimping dies to suit 12 Tonne hydraulic crimpers Commonly referred to as C or U type dies Dies colour coded for easy identification Part No Type Conductor Type A/F (mm) Width (mm) Finish K12-A-9.0 Aluminium 10-35mm² Silver K12-A-13.2 Aluminium 50-70mm² Silver K12-A-17.3 Aluminium mm² Silver K12-A-22.0 Aluminium mm² Silver K12-A-28.4 Aluminium mm² Silver K12-A-14.0 Aluminium OH 7/2.25-7/2.50 OH Silver K12-A-14.5 Aluminium OH 7/2.50 OH Silver K12-A-18.0 Aluminium OH 7/3.00-7/3.75 OH Silver K12-A-19.0 Aluminium OH 7/4.50 OH Silver K12-A-25.4 Aluminium OH 19/3.75 OH Cabac Silver K12-A-26.2 Aluminium OH 19/3.75 OH Utilux Silver K12-C-4.4 Copper 6mm² Gold K12-C-5.7 Copper 10mm² Gold K12-C-6.3 Copper 16mm² Gold K12-C-7.7 Copper 25mm² Gold K12-C-9.2 Copper 35mm² Gold K12-C-10.4 Copper 50mm² Gold K12-C-11.5 Copper 70mm² Gold K12-C-14.2 Copper 95mm² Gold K12-C-16.5 Copper 120mm² Gold K12-C-18.3 Copper 150mm² Gold K12-C-20.0 Copper 185mm² Gold K12-C-23.1 Copper 240mm² Gold K12-C-26.0 Copper 300mm² Gold K12-C-28.1 Copper 400mm² Gold K12-C8.3 Copper OH 7/1.63 & 7/1.70 OH Gold K12-C9.6 Copper OH 7/2.00 & 7/2.03 OH Gold K12-C11.5 Copper OH 7/2.62 OH Gold K12-C13 Copper OH 37/0.064 & 19/2.11 OH Gold K12-C14.8 Copper OH 19/2.0 & 19/2.11 OH Gold K12-C19.3 Copper OH 19/2.57 OH Gold K12-ABC14 ABC mm² Black K12-ABC17.3 ABC mm² Black K12-ABC-21.5 ABC mm² Black Special die sizes available upon request Nest Indent C Connector K13 Quality Electrical Equipment for Generation, Transmission & Distribution

15 Dies 15, 25 & 45 Tonne Part No: K15, K25 & K45 Series Various styles available, compatible with most brand tools, contact TEN for more information Part No Compression (Tonne) Style Type Conductor Type A/F (mm) Width (mm) K15-A**.*U 15 C or U Aluminium Specify Size Specify Specify K15-C**.*U 15 C or U Copper Specify Size Specify Specify K25-A**.*U 25 C or U Aluminium Specify Size Specify Specify K25-C**.*U 25 C or U Copper Specify Size Specify Specify REL Adaptor to crimp 12 Tonne (K12) Dies K45-A**.*R 45 Rectangular Aluminium Specify Size Specify Specify K45-C**.*R 45 Rectangular Copper Specify Size Specify Specify **.* Specify Across Flats dimension in mm. Example: 15T C Type Al Die 23.1mm AF would be K15-A23.1C Dies 60 & 100 Tonne Part No: K60 & K100 Series C or U type and rectangular dies available and are compatible with most brand tools C Type Die Rectangular Die Specify size required when ordering Part No Compression (Tonne) Style Type Conductor Type A/F (mm) Width (mm) K60-A**.*U 60 C or U Aluminium Specify Size Specify Specify K60-C**.*U 60 C or U Copper Specify Size Specify Specify K60-ST**.*U 60 C or U Steel Specify Size Specify Specify K100-A**.*U 100 C or U Aluminium Specify Size Specify Specify K100-ST**.*U 100 C or U Steel Specify Size Specify Specify C Type Die K60-A**.*R 60 Rectangular Aluminium Specify Size Specify Specify K60-ST**.*R 60 Rectangular Steel Specify Size Specify Specify K100-A**.*R 100 Rectangular Aluminium Specify Size Specify Specify K100-ST**.*R 100 Rectangular Steel Specify Size Specify Specify **.* Specify Across Flats dimension in mm. Example: 60T C Type Al Die 39.0mm AF would be K60-A39.0C Special die sizes available upon request Rectangular Die Cutting Dies Part No: Various Cutting dies for crimpers KD Part No Compression (T) Cuts (mm OD) Cu/Al ACSR EHS Guy Wire & Earth Rod Steel Rebar Suits Tool KD X X EK425 (CJD3BG Head) Standard 12T C or U Die Crimpers ASK TEN K14

16 HAND OPERATED TOOLS Cutters up to 85mm OD Part No: Various Two stage double acting hydraulics Ram extends on both open and close Manual pressure release at any stage Flip top latch head Replaceable blades Part No REL-58MC REL-2000MC HSG45 HSG50 HSG85 Head Rotation ( ) Cutting Force (kn/tonne) 53/6 88/10 60/6 60/6 60/6 Safety Valve Yes Yes Yes Yes Yes Length (mm) Maximum Cut OD (mm) Cu Al ACSR X X Wire Rope X X Standard Guy Wire X X ReBar, Ground & Anchor Rods X X Soft Steel Bolts X X Specific Features Auto-Retract, No Disassembly to Replace Moving Blade Magnetic Reservoir traps contaminents, Release at any Stage Auto-Retract, Handle Locking Mechanism Auto-Retract, Handle Locking Mechanism Auto-Retract, Handle Locking Mechanism Storage Device Supplied Replacement Blade Stationary Replacement Blade Moving Carry Bag Carry Bag Steel Case Steel Case Steel Case REL REL ESG45.EF ESG50.EF1 ESG85.EF REL REL ESG45.ES1 ESG50.ES ESG85.Es Weight of Tool (kg) Carry Bag Steel Case K15 Quality Electrical Equipment for Generation, Transmission & Distribution

17 Crimpers 6-12 Ton Part No: Various Two stage double acting hydraulics Ram extends on both open and close Manual pressure release at any stage Part No HK6022 HK60VPFT HK12042 REL-510 Head Rotation ( ) Cutting Force (kn/tonne) 55/6 55/6 130/12 130/12 Pressure (PSI) 10,000 10,000 10,000 10,000 Safety Valve Yes Yes Yes Yes Length (mm) Max Crimp (mm 2 ) Cu Al Specific Features Auto-Retract, Locking Handle Mechanism Auto-Retract, Dieless, Locking Handle Mechanism Auto-Retract, Locking Handle Mechanism Replaceable Drop Out Bypass Fuse Magnetic Reservoir Traps Contaminants Accepts Die Type Standard 6 Ton C / U Type dies No Die Required mm² Standard 12 Ton C / U Type dies Standard 12 Ton C / U Type dies Storage Device Supplied Steel Box with Die Compartments Steel Box Steel Box with Die Compartments Steel Box with Die Compartments Case Weight of Tool (kg) LOW PRESSURE TOOLS & EQUIPMENT Low Pressure Hydraulic Hose Part No: REL2250 Series Twin low pressure flexible hydraulic hose Clear strain relief sleeve over crimped connections Manufactured for use in extreme temperatures -40 C to 100 C Certified non-conductive rubber Impulse tested higher than SAE requirements Supplied with flush face couplers both ends Neoprene inner tube with nitrile outer, reinforced two textile braid Refer to page K34 for protective caps Protective Dust Caps Included Part No * Length (m) * Max Operating Pressure (PSI) Min Burst Pressure (PSI) Electrical Test ASK TEN Hose ID (mm) REL AFF 2.4 2,250 9,000 75kV/3min (>100µA) REL AFF 3.0 2,250 9,000 75kV/3min (>100µA) * Special lengths available upon request Weight (kg) K16

18 DRILLS & ACCESSORIES Hydraulic Impact Drill Part No: REL425CG Lightweight aluminium alloy construction Feather trigger allows control of speed Ergonomic balanced design with finger moulds in trigger Easily changeable forward/reverse push shaft EZ selector valve allows change between open and closed centre systems without tools Supplied with trigger guard and flush face couplers Heat insulated handle Lifetime warranty on motor only Tech Corner Variable torque settings are not recommended, as this can increase the running temperature of the drill when used on a low torque setting. Heat is a major contributor to seal and component damage and can increase maintenance and repair. Part No Chuck Type Operating Pressure (PSI) Flow (Litres/min) Torque 22.7L-min 22.7L/min Weight (kg) with couplers REL425CG 7/16 1,000 2, , REL425CG-1.2 ½ 1,000 2, , Refer to pages M14-16 for bucket mounted drill holsters Drill Socket Adaptors Part No: REL-1137-P High strength socket adaptor for impact drill Spring lock pin 7/16 hex shank with lock groove Part No Specifications Weight (kg) REL-1137-P 7/16 Shank to ½ Drive 0.05 Drill J Hook Pullers & Pole Step Drivers Part No: REL-BJH & REL-PSD High strength hardened steel 7/16 hex shank with lock groove J Hook Puller Part No REL-BJH-7.16 REL-BJH-5.8 REL-PSD REL-PSD Description J Hook Puller 7/16 /11mm Ø J Hook Puller 5/8 /16mm Ø Pole Step Driver 7/16 /11mm Ø Pole Step Driver 5/8 /16mm Ø Pole Step Driver K17 Quality Electrical Equipment for Generation, Transmission & Distribution

19 Impact Augers Part No: TAI Series Designed for Australian hardwood Aggressive lead screw for fast hole boring 7/16 hex shank with lock groove for use with impact drill Heat treated and tempered for long life Flared tip provides smooth and easy retraction Part No Length (mm) Drill Ø (mm) Part No. Length (mm) Drill Ø (mm) AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN AITEN Impact Sockets Part No: IS Series Standard or long shaft ½ Drive Heat treated and tempered for long life Add -L to part number for long sockets Part No Size (mm) Part No Size (mm) IS IS IS IS IS IS IS IS IS IS IS IS IS IS IS IS IS IS IS IS Larger Sockets available with 3/4 drive Part No Size (mm) IS IS IS ASK TEN K18

20 LINE CRIMPERS Crimper 12 Ton Part No: REL-LP-1.5-A For crimping sleeves, joints, lugs, etc Accepts standard 12 Tonne C or U type dies EZ selector valve allows change between open and closed centre systems without tools Relief valve signals operator crimp cycle complete Unique amplifier cylinder design Supplied with trigger guard Flush face couplers fitted Dipped Body & Head Also Available Part No Jaw Opening (mm) System Flow Range (lpm) Pressure (PSI) Force (kn) Head Rotation Weight (kg) REL-LP-1.5-A 38 Open or Closed ,500-2, (Dry) SAWS Pole Saw Refer to page K13 for Dies, and page K16 for Hoses Part No: REL-LR Series Used to safely cut and trim trees and wood, including crossarms Powerful hydraulic drive motor EZ selector valve allows change between open and closed centre systems without tools Foam filled fibreglass shaft to prevent ingress of moisture and provide additional electrical safety protection Every saw supplied electrically tested with report Trigger guard, sprocket guard, rubber hand guard and scabbard Meets OSHA Flush face couplers fitted Part No AREL-LR62.5FF AREL-LR75FF AREL-LR88.5FF OAL (mm) Cut Capacity (mm) 330 System Open or Closed Flow Range (lpm) Operating Pressure (PSI/Bar) 1,000-2,000/ Pressure Port Thread 9/16-18 SAE O-Ring Return Port Thread ¾ -16 SAE O-Ring Chain Pitch (mm) 8.25/25.40 Chain Gauge (mm) 1.47/25.40 Plastic Scabbard SCAB-PS Weight (kg) K19 Quality Electrical Equipment for Generation, Transmission & Distribution

21 Also Available in Tree Trimming Equipment - Pages E9-E11 Circular Pole Saw Pruner Chain Saw Part No: REL-CS16 Used to cut and trim trees and wood, including crossarms Powerful hydraulic drive motor EZ selector valve allows you to change between open and closed centre systems without tools Features reduced kickback bar and chain Quick stop trigger reduces blade coast time for increased safety With knuckle and hand guard Lightweight compared to petrol versions Flush face couplers fitted Other Length Bars available Part No Cut Capacity (mm) System Flow Range (lpm) Pressure Port Thread Return Port Thread Chain Size/ Pitch (mm) Chain Gauge (mm) Weight (kg) REL-CS Open or Closed /16-18 SAE O-Ring ¾ -16 SAE O-Ring DRIVERS & TAMPERS Ground Rod Driver Part No: REL-GRD-1 Works directly off truck hydraulic system from open or closed system Designed to drive ground rods fast Extra long comfort grip handles Lifting eye allows tool to be suspended reducing operator fatigue Part No Drives Rod Ø (mm) Flow (lpm) Operating/Input Pressure Max (PSI/Bar) Ports Whip Hose Length (mm) Unit Length (mm) Wt (kg) REL-GRD ,000/137 9/16 18 SAE O-Ring REL-GRD ,000/137 9/16 18 SAE O-Ring ASK TEN K20

22 Pole Tampers Part No: REL-TMP Series Used for setting poles and general backfill compacting Standard kidney shaped foot included on all models Only three moving parts reduces servicing time Change between open and closed centre systems Flush face couplers fitted VH NV VT Part No Type Length (m) Width (mm) Flow Range (L/min) Pressure Port Thread Return Port Thread Foot Size (mm) Blows Per Min Approx Weight (kg) REL-TMP-60VH Hose End Valve 1.5 REL-TMP-60NV No Valve 1.5 REL-TMP-72VH Hose End Valve 1.8 REL-TMP-72NV No Valve /16-18 SAE O-Ring ¾ -16 SAE O-Ring 60 x L/min 11.0 REL-TMP-72VT REL-TMP-85VH Valve On Tube Hose End Valve POLE PULLERS & HOISTS Pole Puller Part No: Various Works directly off low pressure truck hydraulic system For removal of wooden utility poles Heavy duty chain Unique mechanism pretensions the chain preventing slippage Special design keeps base plate from kicking out Low point of chain attachment allows cutting of pole closer to ground for replacements Cylinder is designed not to rupture should the retraction point coupling become blocked Part No Description Cylinder Stroke (mm) Operating/Input Pressure Max (PSI/Bar) Max Pressure (kg) Wt (kg) 4001D Complete Kit (Cylinder, Swivel Chain Hook Assy, Base Plate & Alloy Chain) 400 2,800/195 22, Optional Extras HA0039 Supports the pole puller on soft ground 4040B Backing Plate with Safety Rib, prevents chain rollup and slippage K21 Quality Electrical Equipment for Generation, Transmission & Distribution

23 Capstan Hoist Part No: C308 Series Works directly off low pressure truck hydraulic systems Small and lightweight, perfect for use in remote and limited access areas Foot control switch & accessories sold separately* Part No WLL (kg) Rope Speed (m per minute)² Source, Minimum Foot Control* C L per minute & 1,000PSI C C ¹ 1, L per minute & 1,000PSI C * Refer B7-B8 in Lifting for electrical and electronic hoists and accessories ¹ Bayonet for Collapsible Reel or Reversible Bayonet for Collapsible Reel also available, contact TEN Weight (KG) Control sold separately Refer to above table HIGH PRESSURE OPERATING SYSTEMS Single Acting High pressure systems generally consist of lighter weight tools and therefore can reduce manual handling injuries & minimise operator fatigue High Pressure Single Acting Systems Hydraulic Power Source Intensifier Control Device Hose Tool/Press Head Press Heads Low Pressure Truck OR Pump Control Knob Crimpers/Cutters High Pressure Pumps Air Switch Punches/Spikers ASK TEN K22

24 Hydraulic Power Source High Pressure Double Acting Systems Intensifier Control Device Hose Tool/Press Head Press Heads Low Pressure Truck Crimpers/Cutters OR High Pressure Pumps Pump Control Knob Spikers Although single acting hydraulic systems offer benefits in certain situations, double acting systems can offer further unique benefits: Better Tool Control No Die Hang-Ups or Ram Wedging Consistent Pressure Quality Features Portability & Manual Handling Adaptability Start, stop, feather, and position your crimping or cutting head with ease Retracts the ram at crimp pressure after every cycle Delivers up to 10,000 psi/700 bar at tool head Built-in pressure reliefs, ground dumps, scavenger pump reduces back pressure problems & one-hand valve operation Light and compact Use your truck s existing system or one of our portable power units, compatible with a variety of hydraulic power sources For more about the benefits of high pressure double acting systems, please contact TEN System Configuration When purchasing hydraulic systems it is important to check the type of couplers/connections on your existing equipment. Coupler Type Flush Face Thread Type Snap Type Reference FF TT ST TEN recommends flush face fittings for both low and high pressure tools as they can be easily wiped clean before connection. K23 Quality Electrical Equipment for Generation, Transmission & Distribution

25 High Pressure HOSES Hose Part No: REL-3VE4 Series Wear resistant flexible thermoplastic with rubber reinforced connection points for strain relief Temperature range -40 C to 66 C and UV resistant Suitable for hydraulic systems operating near high voltage Certified non-conductive, tested to 75kV/300mm as per SAE J517 Spiral high tensile aramid fibre with nylon lined core tube Part No Application Length (m) Operating Pressure (PSI) Min Burst Pressure (PSI) Electrical Test ID Ø (mm) Exceeds Mechanical Specifications REL- 3VE4-**-## Single Acting ** 10,000 40,000 75kV/3min (>50µA) 6.4 SAE J517 REL- 3VE3D-**-## Double Acting ** 10,000 40,000 75kV/3min (>50µA) 4.8 SAE J517 ** Specify length required in metres using full or half sizes, for example: 5m = REL-3VE4D-5.0-##; 5.5m = REL-3VE4D-5.5-## ## Nominate coupler type, see below. For example: FF (Flush Face) = REL-3VE3D-2.0-FF Coupler Type Flush Face Thread Type Snap Type Reference Part Suffix ## FF TT ST Coupler Protective Dust Caps Included Hose with Control Valve Part No: REL-PVA Series Pivot style control valve easily operated with one hand Locks on during crimp and returns to neutral position once crimp pressure reached Features safety valve Wear resistant flexible thermoplastic with rubber reinforced connection points for strain relief Temperature range -40 C to 66 C and UV resistant Suitable for hydraulic systems operating near high voltage Certified non-conductive, tested to 75kV/300mm as per SAE J517 Spiral high tensile aramid fibre with nylon lined core tube Part No REL-PVA021FF-2M REL-PVA122FF-2M REL-PVA022FF-2M Controls Acting Head Type Single Double Double Hose Length (m) 2* 2* 2* Tool End Coupler Type Flush Face¹ (Male) - Flush Face¹ Hose Coupler Type Flush Face¹ Flush Face¹ Flush Face¹ Valve Dimensions LxWxH (mm) 180 x 50 x 90 Operating Pressure (PSI/Bar) 10,000/690 10,000/690 10,000/690 Return Pressure (PSI/Bar) - 5,000/345 5,000/345 Port Size Inlet ¼-18 NPTF ¼-18 NPTF ¼-18 NPTF Port Size Tool ¼-18 NPSM ¼-18 NPSM ¼-18 NPSM Hydraulic Centre Type Open Open Open Valve Weight Incl Oil (kg) * Other lengths available upon request ¹ Other coupler styles available, refer coupler reference above ASK TEN K24

26 HIGH PRESSURE pumps Petrol & Electric Pumps Part No: Various 10,000PSI output pumps Suitable for both single and double acting Two stage pumping piston to ensure rapid tool advance Safety relief valve Reservoirs with oil view gauge Part No REL-1915-** REL-EP-230-** REL-GB-10-** Dimensions (mm) WxDxH 205 x 205 x x 405 x x 660 x 610 Specific Features Top Carry Handle, Comes with Steel Carry Case Carry Handle Tubular Steel Frame Horse Power kw Power Source 240VAC 240VAC Petrol Oil Reservoir (L) Oil Delivery Per Min (cm3) 100 PSI 10,000 PSI 100 PSI 10,000 PSI 100 PSI 10,000 PSI Control Air Switch (Supplied) Knob Knob Weight Incl Oil (kg) ** Range of couplers and adaptors available, specify type when ordering Refer to pages K33-K34 for Adaptors and Couplers K25 Quality Electrical Equipment for Generation, Transmission & Distribution

27 Manual Pump Part No: FHP2 10,000PSI output Two stage hydraulic pump system Manual retraction Strong and sturdy design Part No Capacity (PSI/Bar) Weight (kg) FHP2 10,000/ Range of couplers and adaptors available, specify type when ordering Refer to pages K33-K34 for adaptors and couplers INTENSIFIERS Intensifier Part No: REL10 Series Change low pressure hydraulic source to high pressure without electricity Single, Double and Single/Double acting units available 12 moving parts provide smooth and efficient operation Can be permanently mounted Lightweight and compact Part No REL10I-** REL10I-SA-** REL10I-SDA-** REL-UL-BCA Dimensions (mm) HxLxW 114 x 133 x x 245 x x 245 x x 205 x 195 Specific Features Foldable Carry Handle, Supplied with Nylon Bucket Holder Single Acting Control Knob Single Acting Control Knob Suits # REL10I & # REL10ISA Acting Type Double Single Single & Double - Systems Open or Closed - Drive Type Internal Gear - Pressure (PSI) 800-2,200 1,400-2,000 - Flow (L/min) Optimum Operating Pressure (PSI) 1,800 1,800 - HP Ports ¼ NPT 3/8 NPT - Inlet Port 3/8 NPT - Return Port 3/8 NPT - Weight (kg) ** Range of couplers and adaptors available, specify type when ordering Refer to pages K33-K34 for Adaptors and Couplers ASK TEN K26

28 Remote heads Crimping Heads - 6, 12, 15 & 25 Tonne Part No: Various Single acting, 10,000PSI pressure pump required to operate Part No PK60VPFTC-** PK12042PC-** PK12042UC-** REL-510H-** REL-46-** PK252C-** Force (kn/tonne) 55/6 130/12 130/12 130/12 133/15 222/25 Head Type Flip Top C U / H C C U / H Head Rotation ( ) Oil Capacity (cc) Jaw Opening (mm) Length (mm) Accepts Die Type Not Required /300mm² (Also takes Cembre Deep Indent Dies) Standard 12 Ton C / U Standard 12 Ton C / U Standard 12 Ton C / U P (Accepts Standard 12 Ton C / U with PU adaptor) Klauke Series 45 Die Capacity (mm²) Cu Al Specific Features Dieless No Pinch Point on Ram Weight of Tool (kg) No Pinch Point PK Series heads come with carry bag PK12042PC features no pinch-point on hydraulic ram K27 Quality Electrical Equipment for Generation, Transmission & Distribution

29 Press Heads Tonne Part No: Various 10,000PSI / 700 Bar pressure pump required to operate 60 TONNE Part No REL-60SA-** REL-60SDA-** RK6040-** DK6040-** Force (kn/tonne) 530/60 530/60 530/60 530/60 Acting Type Single Double Single Double Oil Capacity (cc) Stroke Length (mm) Height (mm) Accepts Die Type Standard 60T C / U Type dies (Alcoa, Burndy, Izumi) Standard 60T C / U Type dies (Alcoa, Burndy, Izumi) Izumi EP60S, Burndy L, Alcoa 6000 Izumi EP60S, Burndy L, Alcoa 6000 Die Capacity (mm²) Cu Al Specific Features Removable Die Cap, Wide Base Storage Device Supplied Steel Box Weight of Tool (kg) TONNE Part No REL-100SDA-** HYC-100-** 1 IRP110-** Force (kn/tonne) 980/ / /110 Acting Type Double / Single Double / Single Double / Single Oil Capacity (cc) Stroke Length (mm) Height (mm) Accepts Die Type Standard 100T C / U Type dies (Alcoa, Burndy, Izumi) Die Capacity (mm²) Standard 100T C / U Type dies (Alcoa, Burndy, Izumi) ASK TEN Special Dies required, C or U type can be used with adaptor purchase Cu Al Specific Features Top Carry Handle Removable Die Cap Suspension Eye Incl. Top Carry Handle, Removable Die Cap Skid Base with Control Knob. Top Carry Handle. Flip Top Jaw Pressure Gauge Storage Device Supplied Steel Box - Steel Box Weight of Tool (kg) HYC-100 also available skid base mounted with pressure gauge # HYC100SB ** Range of couplers and adaptors available, Specify type when ordering, Refer to pages K33-K34 for adaptors and couplers K28

30 Cutting Heads up to 85mm OD Part No: Various 10,000PSI pressure pump required to operate Part No REL-58RH-** REL-HP4707SA-** REL-HP4707S-** REL-PDC-2000-** REL-PDC-3000-** Acting Type Single Single Double Double Double Force (kn/t) 55/6 7.9/ / / /5.4 Head Type Guillotine Shear Shear Guillotine Guillotine Head Rotation ( ) Length (mm) Cutting Capacity OD (mm) Cu Soft Jacket Al Jacket ACSR Lead Sheathed X X X Comms Wire Rope Standard Guy Wire 22 EHS ReBar, Ground & Anchor Rods Specific Features Side Handle Side Handle Tool Weight (kg) ** Range of couplers and adaptors available, Specify type when ordering, Refer page K33-34 for Adaptors and Couplers Complete Hydraulic Systems K29 Quality Electrical Equipment for Generation, Transmission & Distribution

31 Cutting Heads up to 120mm OD Part No: Various Single acting, 10,000 PSI pressure pump required to operate Part No SDG45C-** SDG85C-** SDG105C-** SDK85-** SDK105-** SDK120-** Force (kn/ton) 60/6 60/6 120/6 40/4 74/7.4 55/5.5 Head Type Guillotine Guillotine Guillotine Scissor Scissor Scissor Head Rotation ( ) Length (mm) Cutting Capacity OD (mm) Cu Al ACSR 40 X X X X X Standard Guy Wire 18 X X X X X ReBar, Ground & Anchor Rods 16 X X X X X Specific Features - For Armoured Cable Folding Handle For Light Armoured Cable Double Head Balancing Handle Weight of Tool (kg) ** Range of couplers and adaptors available, Specify type when ordering, Refer page K33-34 for Adaptors and Couplers Supplied with carry bag Refer to pages K10 & K31 for Safety Remote Cutters and Live Cable Spiking/Cutting ASK TEN K30

32 Cable Spiking Heads Part No: Various 10,000 PSI/700 Bar pressure pump required to operate For spiking de-energised and possibly live underground cables Part No REL-ST-200-** REL-117ST-** REL-117STM-** REL-ST-10&E-** Acting Type Single Double Double Single Head Type C Flip Top Chain Wrap Chain Wrap Length (mm) Suit Cable OD (mm) (Tapered) (Oval) Specific Features Comes with 20 Replaceable Spiking Probes. Probes Reusable. Earthing Bolt on Head (Also avail in kit # REL- ST-200K as above with Hand Pump 10,000 PSI with HP Non-Conductive Hose) Easy Operator Change to Tapered or Oval Head. Two Earthing Lug Holes on each Side Specially Designed Spike & Guide Blade Design to avoid Jamming Specially Designed Spike & Guide Blade Design to avoid Jamming and for Multi-Bundled Cable Weight of Tool (kg) ** Range of couplers and adaptors available, specify type when ordering, Refer page K33-34 for adaptors and couplers Punches Part No: REL-35T-PNC Single acting 10,000 PSI/700 Bar pressure pump required to operate For punching aluminum, copper or steel Applications include busbars, transmission towers, railings and I-beams Stripper guide extends on either side of ram to strip material after punching Supplied in steel carry case with four die sets Part No Force (kn/ton) Max Capacity (mm) Max Hole (mm) Die Sizes (mm) Dimensions (mm) Throat Depth (mm) Weight (KG) REL-35T-PNC-** 31/35 13 Mild Steel 21 10, 13, 16 & x 200 x ** Range of couplers and adaptors available, specify type when ordering, Refer page K33-34 for adaptors and couplers K31 Quality Electrical Equipment for Generation, Transmission & Distribution

33 Safety, Quality & Reliability Line Hydraulics Low & High Pressure Intensifiers Hand Hydraulics Crimping & Cutting Vegetation Management Punching and Spiking Hydraulic Pumps RELIABLE by name, RELIABLE by nature We service and repair: Service & Repair Hydraulic Battery Tools Line Hydraulics Hand Tools Hoists Machinery Jumper/Bonder Refurbishment Regular service and maintenance of your tools minimises downtime and ensures the job is done safely and accurately ASK TEN K32

34 COUPLERS & ADAPTORS High Pressure Couplers Part No: Various 10,000PSI/700 Bar working pressure, hydraulic tool and hose connections Installation by qualified person recommended Coupler Type Flush Face Thread Type Snap Type Reference FF TT ST Coupler ¼ Part No REL REL REL REL Thread Type NPT - - OAL (mm) /8 Part No REL REL REL REL REL-TC-371 REL-TC-372 Thread Type NPT NPSF OAL (mm) Protective Cap 1/4 Part No REL REL /8 Part No REL REL TR-37 TR-37 K33 Quality Electrical Equipment for Generation, Transmission & Distribution

35 Low Pressure Couplers Part No: Various 2,250PSI hydraulic tool and hose connections Installation by qualified person recommended Coupler Type Reference Flush Face FF Type Male Female Male/Female Kit Part No REL REL REL Thread Type 3/8-18 NPSF 3/8-18 NPSF 3/8-18 NPSF OAL (mm) N/A Protective Cap Adaptors Part No NR-50 NR-37 NR-50 & NR-37 Part No: Various Reducers, female to female nut joiners, male to male connectors and adaptors Installation by qualified person recommended Part No Reference Description Thread NPT JN9M Adaptor Right Angle NPT 1/4" Thread, 31.5/31mm 1/4" 1 JN9M Adaptor Right Angle NPT 3/8" Thread, 36.5/32mm 3/8" N1F Socket Adaptor Nut NPT 1/4" Thread 1/4" 2 N1F Socket Adaptor Nut NPT 3/8" Thread 3/8" N1M Nipple Hydraulic NPT-NPT Straight 1/4" - 1/4" 1/4" N1M Nipple Hydraulic NPT-NPT Straight 3/8" - 1/4" 3/8" - 1/4" N1M Nipple Hydraulic NPT-NPT Straight 3/8" - 3/8" 3/8" N1R Nipple Hydraulic NPT-NPT Reducer 3/8" - 1/4" 3/8" - 1/4" NP-04 Plug Bolt NPT 1/4" thread 1/4" 5 NP-06 Plug Bolt NPT 3/8" thread 3/8" ASK TEN K34

36 FLOW & PRESSURE INSTRUMENTS FOR LOW & HIGH PRESSURE Flow & Pressure Gauges Part No: REL-PG & REL-FPG Series For identifying flow and pressure issues with truck or pump hydraulic systems Portable hydraulic fault identification tool Connect in series with hose, no tools required In-Line Pressure Guage In-Line Flow & Pressure Guage Part No REL-PG-LP Part No REL-PG-HP-** Part No REL-FPG Hydraulic Type Max Gauge Reading (PSI) Wt (kg) Hydraulic Type Max Gauge Reading (PSI) Wt (kg) Hydraulic Type Max Gauge Reading (PSI) Wt (kg) Low Pressure 3,000 1 High Pressure 15,000 1 Low Pressure 3,000 2 ** Range of fittings and adaptors available on request Compression Tester, 12 Ton Part No: RELCG12T&D For testing compression output of 12 Tonne crimpers Portable hydraulic fault identification tool Part No Max Gauge Reading (PSI/Bar) Weight (kg) How would you know if your tool isn t crimping to the right pressure? RELCG12T&D 15,000/ K35 Quality Electrical Equipment for Generation, Transmission & Distribution