CUTTERS REL-3000SA REL-2000SA & REL-58RH SINGLE ACTING HYDRAULIC CUTTING HEAD H/P SINGLE ACTING HYDRAULIC SINGLE ACTING HYDRAULIC CUTTING TOOL

Transcription

1 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION Head opens for cable insertion along the line Head opens for cable insertion along the line CUTTERS REL-3000SA REL-2000SA ACSR REL-58RH REL-3000SA SINGLE ACTING HYDRAULIC CUTTING TOOL This guillotine-type cutter will make a straight, clean cut every time. These cutters can be used for cutting a wide range of electrical conductors. Head opens easily for inserting cable at any location along line. This Single acting cutter will compliment existing single acting systems. The 360 º rotating head eliminates hose twisting and increases operator speed and comfort. MODEL REL-3000SA REL-2000SA REL-58RH Capacity (Jaw Opening) Cutting 10,000 psi (690 bar) Max Op. Pressure 3.35 in. 2 in. 1 in. 11,000 lb. 28,048 lb. 12,000 lb. 10,000 psi 10,000 psi 10,000 psi Weight 21 lbs lbs. 4.0 lbs. Length 17.5 in in in. Width 7.5 in. 6.5 in in. REPLACEMENT BLADES: REL-3000SA Fixed #: R30007 Movable #: R30004 REL-2000SA Fixed #: R23035 Movable #: R23001 REL-58RH Fixed #: R36003 Movable #: R36006 Replacement parts are available for all Reliable products. Contact Reliable Parts Department for price and availability. REL-2000SA & REL-58RH SINGLE ACTING HYDRAULIC CUTTING HEAD Among the smallest hydraulic cutting heads available. Designed to cut copper, aldrey, aluminum, ACSR, guy wire, steel ropes, and ground rod. The blades are manufactured from high strength special steel, heat treated to ensure a long service life. The head can rotate by 180 º, to enable the operator to work in the most comfortable position, and can easily be opened to allow the cutting of running cables. MAXIMUM CONDUCTOR CAPACITY MODEL REL-3000SA REL-2000SA REL-58RH Soft Copper/ Jacket Aluminum/ Jacket Communication Cable Lead Sheath Cable 3 in. 2 in. 1 in. 3 in. 2 in. 1 in in. 2 in in. 2 in. DO NOT CUT DO NOT CUT ACSR DO NOT CUT 2 in. 1 in. Wire Rope DO NOT CUT 1 in. 3/4 in. Guy Strand DO NOT CUT 3/4 in. 3/4 in. (5/8 EHS) Ground Rod DO NOT CUT 3/4 in. 5/8 in. Soft Steel Bolts DO NOT CUT 7/8 in. 7/8 in. Anchor Rod DO NOT CUT 3/4 in. 1/2 in. Rebar Grade 40 DO NOT CUT 3/4 in. 5/8 in. H/P SINGLE ACTING HYDRAULIC 47

2 CUTTERS REL-4000SA Full 4 Inch Copper and Aluminum Cutting Capacity REL-4000SA SINGLE ACTING HYDRAULIC 4" CUTTING TOOL The REL-4000SA single acting hydraulic cutter has been designed to accommodate copper and aluminum conductor up to 4 inches in diameter. The body and handle have been designed to provide comfort, and to protect the operator from inadvertent contact with the blade or mechanism. Hardened steel blades cut clean with minimal distortion. High Pressure Female Coupler Included DO NOT CUT STEEL NOTE: 6 Inch Cu & Al Cutting Capacity Available. (See D/A Cutters) MODEL REL-4000SA Weight 17.5 lbs. Size 15.6" x 10" x 4". System Hydraulic - 10,000 psi max. Connection 3/8 Screw Type (Female) Max. Cut 4 inch dia. (Cu or Al) DO NOT CUT STEEL H/P SINGLE ACTING HYDRAULIC MAXIMUM CONDUCTOR CAPACITY MODEL Copper Aluminum Copper Weld Alumoweld HP4707SA Standard ACSR Blade Set HP4707SA 1,000 MCM 1,033.5 MCM 7/8 AWG 7/8 AWG HP4707SA SINGLE ACTING HYDRAULIC CABLE CUTTER The HP4707SA single acting hydraulic cable cutter is ideal for cutting individual conductors or communication cable. The HP4707SA will cut individual copper or aluminum conductors up to 1,000 MCM, and can even cut ACSR up to 954 MCM with the standard ACSR blade set. Simplicity, speed, and convenience make the HP4707SA cutter the perfect addition to any single acting tool inventory. MODEL System Capacity (Jaw Opening) Cutting 10,000 psi (690 bar) Max Operating Pressure Connection Weight HP4707SA Single Acting 1.25 in. 17,720 lb. 10,000 psi 3/8 Screw Type (Female) 8.0 lbs. ACSR /7 Length 15 in. Comm. Cable 1 in. Width 4 in. 48 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

3 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION SP-20 SP-24 SP-32 CUTTERS SP-40 SP-55 SP-SERIES - HYDRAULIC OPERATED CUTTING HEADS These remote head units connect to any 10,000 psi, high pressure, hydraulic pumping system. Choose from seven different models of production cutters, to cut cost and effort. A 3/8 screw-type male coupler is supplied with each tool. The remote cutters have a hinged head which can be opened for easy cable or bar insertion. The movable blade advances in a shear fashion, to cut the material cleanly. When the cutting pressure is relieved, an internal ram spring retracts the blade. The guillotine cutting style was chosen over scissor type cutting because of its powerful output force, larger cable capacities, compact size and reliability. All tools can be used under water: Consult Reliable for specific applications. MODEL SP-20 SP-24 SP-32 SP-40 SP-55 Weight 3 lbs. 6 lbs. 21 lbs. 8.5 lbs. 20 lbs. Jaw Opening Output 4.4 Ton 7.8 Ton 20 Ton 6.28 Ton Ton Length 8" 11" 14" 12" 17" CUTTING CAPACITIES Wire Ropes 5/8" 7/8 1-1/4 Do Not Cut 1" Soft Steel Bolts 9/16" 3/4" 1-1/4" 5/8" 7/8" Rebar, Ground & Anchor Rod 1/2" 5/8" 1" 5/8" 3/4" ACSR 3/4" 7/8" 1-1/4" 1-1/2" 2" Standard Guy Strand 1/2" 5/8" 7/8" 5/8" 3/4" H/P SINGLE ACTING HYDRAULIC 49

4 CUTTERS H/P SINGLE ACTING HYDRAULIC 50 SP-85 SP-100 SP-24CC SP-85 & SP-100 COMMUNICATION CABLE CUTTERS SP-SERIES remote head units connect to any 10,000 psi, high pressure, hydraulic pumping system. Choose from seven different models of production cutters, to cut costs and efforts. A 3/8" screw-type male coupler is supplied with each tool. These cutters have a hinged head which can be opened for easy cable or bar insertion. The movable blade advances in a shear fashion, to cut the material cleanly. When the cutting pressure is relieved an internal ram spring retracts the blade. The guillotine cutting style was chosen over scissor type cutting because of its powerful output force, larger cable capacities, compact size and reliability. All tools can be used under water, consult factory for specific applications. FEATURES: Lightweight and portable Operate from any 10,000 psi Hydraulic Source Works in any position SP-24CC - EHS GUY WIRE CUTTER This hydraulic cutter has been specially engineered to cut the toughest EHS guy wire, ground, and anchor rods. The anvil style center cut blades eliminate jamming problems common to shear style cutters, and the blades are easily replaced in the field. The tools are made of high grade steel. All tools are black zinc oxide coated to help reduce corrosion. A flip top latch opens the tool jaw to easily accept cables and wires. FEATURES: Lightweight and portable Works in any position Anvil blades eliminate jamming Blades are easily replaced in the field MODEL SP-85 SP-100 SP-24CC Output 2.7 Ton 8.3 Ton 7.4 Ton Weight 16 lbs. 29 lbs. 6 lbs. Length 19" 24" 11" Communication Cable to 3.35" Cable to 4" N/A Lead Sheath Cable to 3.35" Cable to 4" N/A Soft Cu & Al Cable to 3" Cable to 3-1/2" N/A ACSR DO NOT CUT DO NOT CUT N/A Standard Guy Strand DO NOT CUT DO NOT CUT N/A EHS Guy Wire DO NOT CUT DO NOT CUT 9/16" Anchor Rod DO NOT CUT DO NOT CUT 5/8" Ground Rod DO NOT CUT DO NOT CUT 5/8" Grade 80 Chain DO NOT CUT DO NOT CUT 1/4" QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

5 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION PDC 2000 & PDC 3000 DOUBLE ACTING CABLE CUTTERS Guillotine-type cable cutters are available in sizes from 2 in. through 4 in. capacities. These cutters can be used in a wide range of applications for cutting electrical conductors. The model PDC 2000 also cuts wire rope, soft steel bolts, guy strand, ground rods, anchor bolts and rebar. All models will make a straight, clean cut every time. FEATURES Lightweight, compact guillotine design provides a clean, positive cut Cutting head is easily opened for inserting cable at any location along the line 360 º rotating head eliminates hose twisting. Built-in Auxiliary Handle PDC 2000 CUTTERS & MAXIMUM CONDUCTOR CAPACITY MODEL PDC 2000 PDC 3000 Soft Cu & Al /Jacket 2 in. 3 in. Comm. Cable & Lead Sheath Cable 2 in in. ACSR 2 in. Do Not Cut Wire Rope 1 in. Do Not Cut Guy Strand & Ground Rod 3/4 in. Do Not Cut Soft Steel Bolts 7/8 in. Do Not Cut Anchor Bolts & Rebar Grade 40 3/4 in. Do Not Cut System Double Acting Double Acting Capacity (Jaw Opening) Cutting 10,000 psi (690 bar) Return 5,000 psi (345 bar) Max Operating Pressure Max Return Pressure 2 in. 3 in. 28, 049 lb. 11,000 lb. 10,445 lb. 2,922 lb. 10,000 psi (690 bar) 5,000 psi (345 bar) 10,000 psi (690 bar) 5,000 psi (345 bar) Weight 16.5 lbs lbs. Length x Width 17.5 in. x 6.5 in in. x 7.5 in. PDC 3000 H/P DOUBLE ACTING HYDRAULIC 51

6 CUTTERS REL-6000DA REL-6000DA DOUBLE ACTING HYDRAULIC CUTTING TOOL This guillotine-type cutter will make a straight, clean cut every time. These cutters can be used for cutting a wide range of electrical conductors. Head opens easily for inserting cable at any location along line. Double acting operation eliminates hang-up problems, and offers full control of cutting action. The 360 º rotating head eliminates hose twisting and increases operator speed and comfort. Compact guillotine design provides a clean, positive cut up to 6 inches Cutting head easily opens for insertion of cable at any location along line 360 º rotating head eliminates hose twisting Built-in Auxiliary Handle HP4707S DOUBLE ACTING HYDRAULIC CABLE CUTTER Ideal for cutting individual conductors or communication cable. Double acting operation eliminates hang-up problems from metal flash, and offers full control of cutting action at all times. The 360 º rotating head eliminates hose twisting and increases operator speed and comfort. Double acting operation eliminates hang-up problems from metal flash Full control of cutting action at all times 360 º rotating cutter head eliminates hose twisting H/P DOUBLE ACTING HYDRAULIC HP 4707S MODEL REL-6000DA HP 4707S System Double Acting Double Acting Capacity (Jaw Opening) 6 inch 1.25 in. Cutting 10,000 psi (690 bar) 46,000 lb. 17,720 lb. Return 5,000 psi (345 bar) 2,922 lb. 4,950 lb. Max Operating Pressure 10,000 psi (690 bar) 10,000 psi (690 bar) Max Return Pressure 5,000 psi (345 bar) 5,000 psi (345 bar) Weight 16.5 lb. 8.7 lb. Length 17.5 in. 15 in. Width 6.5 in. 4 in. Couplers 3/8 Screw Type Direct Connect MAXIMUM CONDUCTOR CAPACITY MODEL REL-6000DA HP 4707S Copper 6 in. 1,000 MCM-Cu Aluminum 6 in. 1,033.5 MCM-Al Copper Weld DO NOT CUT 7/8 AWG Alumoweld DO NOT CUT 7/8 AWG ACSR DO NOT CUT /7 Comm. Cable 6 in. 1 in. Lead Sheathed Cable 6 in. 52 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

7 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION S-16 S-20 S-32 S-40B CUTTERS S-55 S-85 S-32CC S-240CC HUSKIE - S-SERIES - HYDRAULIC OPERATED CUTTERS Cut anything from *guy wire to anchor rod and most overhead and underground cables. The S-Series cutters are portable, lightweight, and made to last years under the toughest field conditions. The S-40B and S-85 feature a two-stage pumping piston for rapid advance. *NOTE: DO NOT CUT EHS GUY WIRE. FOR EHS GUY WIRE SPECIFY S-240CC, S-32CC OR THE REMOTE HEADS SP-24CC OR SP-32CC1. MODEL S-16 S-20 S-32 S-40B S-55 S-85 S-32CC S-240CC Output 4.4 Ton 4.4 Ton 19.8 Ton 6.3 Ton 13.0 Ton 2.7 Ton 19.8 Ton 7.8 Ton Weight 6 lbs. 6 lbs. 21 lbs. 12 lbs. 17 lbs. 15 lbs. 23 lbs. 11 lbs. Length 15" 15" 27" 23" 24" 26" 27" 18.5" Jaw Opening 0.6" 0.75" 1.25" 1.6"" 2" 3.3" 1.25" 0.9" CUTTING CAPACITIES Wire Ropes 5/8" 3/4 1-1/4" 3/4" 1" Do Not Cut Do Not Cut Do Not Cut Soft Steel Bolts 5/8"" 11/16" 1-1/4" 3/4" 1-1/4" Do Not Cut 5/8" 5/8" Rebar, Ground & Anchor Rod 1/2" 5/8" 7/8" 5/8" 3/4" Do Not Cut 5/8" 5/8" Cu & Al Wire 5/8" 3/4" 1-1/4" 1-1/2" 2" 3" Do Not Cut ACSR 5/8" 3/4" 1-1/4" 1-1/2" 2" Do Not Cut Do Not Cut Standard Guy Wire 1/2" 1/2" 7/8" 7/8" 3/4" Do Not Cut 7/8" 9/16" EHS Telephone & Lead Sheathed Cable Do Not Cut Do Not Cut Do Not Cut Do Not Cut Do Not Cut 3.35" Do Not Cut Do Not Cut MANUAL HYDRAULIC 53

8 CUTTERS REL-58MC 6 TONS OF CUTTING FORCE REL-58MC MANUAL HYDRAULIC CUTTING TOOL Among the smallest hydraulic cutting tools available. Designed to cut copper, aldrey, aluminum, ACSR, EHS guy wire, steel ropes, and steel ground rod. The tool features a double speed action. The blades are manufactured from high strength special steel, heat treated to ensure a long service life. The head can rotate by 180 º, to enable the operator to work in the most comfortable position, and can easily be opened to allow the cutting of running cables. RE-58MC features an automatic safety valve to bypass oil when reaching maximum pressure; a pressure release device can also be operated at any stage of operation. MANUAL HYDRAULIC REL-2000MC REPLACEMENT BLADES Movable Blade: R36006 Fixed Blade: R36003 REPLACEMENT BLADES Movable Blade: R51005 Fixed Blade: R51006 REL-2000MC MANUAL HYDRAULIC CUTTING TOOL This guillotine-type cutter will make a straight, clean cut every time. These cutters can be used for cutting a wide range of electrical conductors. The head opens easily for inserting cable at any location along the line. Designed to cut copper, aluminum, ACSR, guy wire, soft steel bolts, rebar, ground and anchor rod. Two stage pumping piston for rapid advance, and twist handle release. Magnetic oil reservoir plug traps metal contaminants. The blades are manufactured from high strength special steel, heat treated to ensure a long service life. MODEL REL-2000MC REL-58MC Weight 18 lbs. 7.7 lbs. Length 24 in in. Pressure 10,000 psi 10,000 psi CUTTING CAPACITIES Wire Ropes 1 in. 3/4 in. Soft Steel Bolts 1-1/4 in. 7/8 in. Rebar, Ground & Anchor Rod 3/4 in. 5/8 in. Cu. & Al. Wire 2 in. 1 in. ACSR 2 in. 1 in. Guy Wire 3/4 in. 3/4 in. (5/8 EHS) Lead Sheathed & Telephone Cable 2 in. DO NOT CUT 54 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

9 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION GEAR-DRIVEN CABLE CUTTERS REC-54M 2" JAW OPENING Primarily used to cut up to 1590 MCM ACSR* Huskie Tools has notched both cutting blades to avoid the denting of the cutting surfaces when steel strand is encountered. We have rotated the handle 90 to the blade to achieve a more ergonomic and comfortable cutting position. The REC-54M is not intended to cut guy wires, ground rod or bolts. REC-54ACM 2-1/8" JAW OPENING Designed to cut stranded copper cables and aluminum. The jaws will accept a maximum of 1500 MCM aluminum. The operation of this tool is the same as the REC-54M, but it has sharper blades for cutting only non-ferrous materials. Do not cut steel with this model, or blade damage will occur. KITS INCLUDES Battery Powered Tool 1 Carrying Case 1 CH-94 Charger 2 BP-84 Lithium Ion Batteries 1 Carrying Strap This charger can charge the BP-84, BP-82 and BP-80 only. Huskie Tools batteries, including the BP-70, BP-70EI and the BP-70MH MUST be charged with the CH-90, CH-80, or previous charger models. BP-84 Lithium Ion Battery REC-54M REC-54ACM CUTTERS CH-94 Charger ES2522 Cuts ACSR type cables through 636 kcmil (except Egret) Capable of making approximately 50 cuts of Grosbeak or 120 cuts of Merlin per battery charge Blades are specially contoured and hardened to cut both aluminum and steel strands Powerful 14.4 volt battery charges in less than one hour Includes two batteries, battery charger, and molded carrying case MODEL REC-54ACM REC-54M ES2522 Weight 7.2 lbs. w/ Battery 8 lbs. w/ Battery 7.7 lbs. w/ Battery Jaw Opening 2-1/8" 2 Size 16"L x 4"H x 4.5"W 15.5 L x 4.5 H x 5 W 21 L x 4.5 H x 5 W Cutting Estimates Cutting Capacities BP: MCM Cu : MCM Al: 30 Al: 1500 MCM Cu 1000 MCM BP: MCM ACSR: 35+ Al: 750 MCM Cu: 1500 MCM ACSR: 1590 MCM 636 KCMIL (Except Egret) ACSR 1500 KCMIL Al Cable ES2522 BATTERY GEAR-DRIVEN 55

10 CUTTERS 18.0 V BATTERY POWERED HYDRAULIC CUTTING TOOLS B-TC650A B-TC650-SCA New Li-Ion 18 V 4 Ah batteries offer a higher capacity than 14.4 V 3 Ah, while greater cutting speed and cutting force result from a revitalized hydraulic system with double speed action. The battery is equipped with led indicators that indicate the remaining battery life at any time by pressing the adjacent button. Fitted with a maximum hydraulic pressure valve. Designed with improved balance, easily manageable during the cutting process. Rubber grip inserts, low noise and minimal vibration aid operator comfort while additional convenience and safety are provided by LED lighting of the working area. B-TC650A Specifically designed to cut copper, aluminum and telecommunication cables having a max overall diameter of 2-9/16. THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery Battery charger Plastic carrying case B-TC650-SCA Specifically designed for cutting copper, aluminum and telecommunication cables having a max overall diameter of 2-9/16. The open head and the scissor movement of the blades facilitate the cutting of running cables. BATTERY HYDRAULIC B-TC950A The working hours are automatically stored on a memory card for transfer to PC by USB interface. THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery AC charger (110V) Metal carrying case B-TC950A Specifically designed to cut Copper, Aluminum and telecommunication cables having a max overall diameter of 3-3/4. NOT SUITABLE FOR CUTTING STEEL REINFORCED CONDUCTORS THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery 8AC charger ( V) Metal carrying case MODEL B-TC650A B-TC650-SCA B-TC950A Weight 14.1 lbs. w/ Battery 16.9 lbs. w/ Battery 17.1 lbs. w/ Battery Cutting Capacities 2-9/16" 2-9/16 3-3/4 Size 16.9"L x 16.3"H x 3.3"W 19.8 L x 18.3 H x 4.1 W 20.4"L x 18.4"H x 3.3"W Operating Temperature +5 to +122ºF +5 to +122ºF +5 to +122ºF Head Rotation 335º 180º 335º 56 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

11 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION 18.0 V BATTERY POWERED HYDRAULIC CUTTING TOOLS New Li-Ion 18 V 4 Ah batteries offer a higher capacity than 14.4 V 3 Ah, while greater cutting speed and cutting force result from a revitalized hydraulic system with double speed action. The battery is equipped with led indicators that indicate the remaining battery life at any time by pressing the adjacent button. Fitted with a maximum hydraulic pressure valve. Designed with improved balance, easily manageable during the cutting process. Rubber grip inserts, low noise and minimal vibration aid operator comfort while additional convenience and safety are provided by LED lighting of the working area. B-TC500YA Specifically designed to cut Copper, Aluminum, Aluminum-Steel cables (ACSR) having a max overall diameter of 2. For ACSR only, not suitable for cutting guy wire and ground rod. THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery Battery charger Plastic carrying case B-TC500YA B-TC550A CUTTERS B-TC550A Specifically designed to cut copper, aluminum, aluminum-steel cables (ACSR) steel ropes and rods having a max overall diameter of 2-3/16. Ideal for 795 MCM ACSR Drake and EHS guy wire. THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery AC charger ( V) Metal carrying case B-TC500A Specifically designed to cut copper, aluminum and telecommunication cables having a max overall diameter of 2. Not suitable for cutting steel reinforced conductors. THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery Battery charger Plastic carrying case MODEL B-TC500YA B-TC550A B-TC500A Weight 12.7 lbs. w/ Battery 19.6 lbs. w/ Battery 12.7 lbs. w/ Battery Cutting Capacities 2" 2-3/16 2 Size 15.9"L x 15.6"H x 3.3"W 17.4 L x 16.7 H x 3.4 W 15.9"L x 15.6"H x 3.3"W Operating Temperature +5 to +122ºF +5 to +122ºF +5 to +122ºF Head Rotation 90º 327º 90º B-TC500A BATTERY HYDRAULIC 57

12 CUTTERS ESG45L12 BATTERY POWERED CABLE CUTTERS ESG25L12 Greenlee s Battery-powered In-line Cutters are hand-held, self-contained cutting tools intended to cut the following: Copper and aluminum cable up to 1" (25 mm), 636 ACSR, 3/8" reinforcement bar (rebar), 5/8" stranded guy wire and 1/2" wire rope. It is not intended for use on EHS guy wire. FEATURES Designed primarily to cut distribution ACSR cable Powerful state of the art 18V lithium ion battery LED light provides the operator with the battery charge and tool maintenance status In line tool style is light weight and very easy to control One trigger controls all tool functions Cutting head rotates 350 Tool automatically retracts when the cutting cycle is complete LED work light illuminates dark work areas BATTERY HYDRAULIC SL-S20 SL-S20 Designed to cut the toughest steel used in construction today. It can replace an entire tool kit, including several sizes of conventional bolt cutters,hacksaws, acetylene torches and cable cutters. With the pull of a trigger, you can cut ACSR cables up to 477, standard guy wires to 3/8", and ground rods to 1/2". The specially designed flip-top latch and rotating head provide exceptional ease of use and maneuverability in tight working quarters. FEATURES Flip-Top Latching Head Tested Up to 75kV One Hand Operation Rotational Head Bright White, LED Lights for Working in Low Light Conditions Rapid Advance 5 Year Warranty on Tool, Battery & Charger MODEL ESG25L12 SL-S20 Weight 4.6 lbs lbs. w/ Battery Size 15"L x 4.5"H x 3"W 18.5 L x 3.7"H x 2.8"W Cutting Performance Approximately 100/charge Approximately 84/charge Cutting Capacities Cutter Head Opening: 1 in. ACSR: 636 KCMIL Guy Strand (Not EHS): 5/8 in. Ground Rod: 3/8 in. Rebar (SCH 60): 3/8 in. Wire Rope: 1/2 in. Wire Rope: 5/8in. Rebar (Sc 40): 1/2 in. Rebar (Sc 60): 3/8in. Ground Rod: 1/2 in. ACSR: 477 MCM Guy Wire: 3/8 in. 58 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

13 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION 18.0 V BATTERY POWERED HYDRAULIC CUTTING TOOLS B35M-TC025A Balanced for greater control and can be operated with one hand Fitted with a maximum pressure valve. Extremely quiet, minimal vibration. Durable moulded body offering high resistance to wear and damage in all operating conditions. New Li-Ion 18V 2Ah High Power battery with LED indicators to show the remaining battery life Specifically designed cut copper, aldrey, aluminum, aluminumsteel cables, steel ropes having a max overall diameter of 1", guy wire up to 7/8" and steel ground rod up to 5/8" THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery Battery charger Plastic carrying case B-TC250YA & B-TC450A New Li-Ion 18 V 4 Ah batteries offer a higher capacity than 14.4 V 3 Ah, while greater cutting speed and cutting force result from a revitalized hydraulic system with double speed action. The battery is equipped with led indicators that indicate the remaining battery life. Fitted with a maximum hydraulic pressure valve. Designed with improved balance, easily manageable during the cutting process. Rubber grip inserts, low noise and minimal vibration aid operator comfort while additional convenience and safety are provided by LED lighting of the working area. B-TC250YA Specifically designed cut copper, aldrey, aluminum, aluminum-steel cables, steel ropes having a max overall diameter of 1", guy wire up to 7/8" and steel ground rod up to 5/8". THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery AC charger ( V) Plastic carrying case B-TC450A Specifically designed to cut copper, aldrey, aluminum, aluminumsteel cables, steel ropes, Aluminum and Steel rods having a max overall diameter of 1-3/4 in. IDEAL FOR EHS GUY WIRE. THE TOOL IS SUPPLIED AS: Basic tool w/ battery & shoulder strap Spare battery Battery charger Plastic carrying case B35M-TC025A B-TC250YA B-TC450A CUTTERS BATTERY HYDRAULIC MODEL B35M-TC025A B-TC250YA B-TC450A Weight 6.8 lbs. w/ Battery 10.5 lbs. w/ Battery 14.7 lbs. w/ Battery Size 15.4"L x 5.2"H x 3.2"W 12.2 L x 13.5 H x 3.3 W 16"L x 15.8"H x 3.5"W Operating Temperature +5 to +122ºF +5 to +122ºF +5 to +122ºF Head Rotation 180º 180º 180º Cutting Capacities 1" /64 59

14 CUTTERS ESG45L12 BATTERY POWERED CABLE CUTTERS FEATURES Designed specifically to cut ACSR, guy strand and ground rods State of the art 18V lithium ion (Li-ion) battery provides 70% more cycles per charge and faster cycle times Retraction Stop allows the operator to stop the ram retraction at any point simply by tapping the trigger, and then starting the next cutting cycle from that point saving time and energy LED light provides the operator with the battery charge and tool maintenance status Two-stage hydraulic system provides fast advance and power speeds, saving time Forward handle position improves tool balance One trigger controls all tool functions Tools automatically retract when the cutting cycle is complete Overmolded tacky grip areas make gripping the tool easier and more comfortable LED work light illuminates dark work areas Smart chargers control the charging current, charging voltage and battery temperature to maximize battery life Available with 120V, 12V or 230V battery charger or with 120V or 230V corded adapter in place of batteries and charger ESG45L12 Greenlee s Battery-powered Pistol Grip Cable Cutters are hand-held tools intended to cut the following: ACSR and guy strand BATTERY HYDRAULIC ESG55L12 ESG55L12 Greenlee s Battery-powered Pistol Grip Cable Cutters are hand-held tools intended to cut the following: ACSR and guy strand MODEL ESG45L12 ESG55L12 Weight 13 lbs. w/ Battery 17.5 lbs. w/ Battery Max. Cable Cutting Diameter 1-3/4 in. 2-1/2 Size 16-5/8"L x 13"H x 3"W 18 L x 13"H x 3"W Cutting Performance Approximately 90/charge Approximately 80/charge Head Rotation 350º 350º Cutting Capacities ACSR: 1590 KCMIL (Falcon 54/19) Standard Guy Strand: 5/8 in. EHS Guy Strand: 1/2 in. Ground Rod: 5/8 in. Rebar (SCH 60): 1/2 in. Wire Rope: 5/8 in. Copper & Aluminum Cable: 1500 KCMIL ACSR: Joree 76/19 AWG (2515KCMIL) Standard Guy Strand: 5/8 in. Diameter EHS Guy Strand: 9/16 in. Diameter Ground Rod: 3/4 in. Diameter Rebar (SCH 60): 5/8 in. Diameter Soft Steel Bolts: 3/4 in. Diameter 60 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

15 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION BATTERY POWERED CABLE CUTTERS ESG50L11 For cutting copper and aluminum power cables Retraction Stop allows the operator to stop the ram retraction at any point simply by tapping the trigger, and then starting the next cutting cycle from that point saving time and energy Two-stage hydraulic system provides fast advance and power speeds, saving time Tools automatically retract when the cutting cycle is complete Smart chargers control the charging current, charging voltage and battery temperature to maximize battery life ESC105L11 For cutting large diameter underground power and communications cables, including armored cables Retraction Stop allows the operator to stop the ram retraction at any point simply by tapping the trigger, and then starting the next cutting cycle from that point saving time and energy Two-stage hydraulic system provides fast advance and power speeds, saving time Scissor-style blades are easy to fit around cables Tools automatically retract when the cutting cycle is complete Smart chargers control the charging current, charging voltage and battery temperature to maximize battery life PATCUT245CUAL Incorporates a specialized latch style cutting head that allows interference-free closure for mid-span cuts. It is capable of cutting up to 2.45-inches diameter copper and aluminum cable. It operates on industry standard 18-volt Ni/MH batteries that eliminate voltage depression or memory issues. It comes equipped with a high impact formed carrying case to hold the tool, a tool retention lanyard, a battery charger and two batteries. This is provided with a 5-year limited warranty (excluding blades), and 1-year on batteries and charger. Battery powered cutting technology. Easy tool operation and portability. Advance design high-speed pump completes tough cuts faster. Longer life, efficiency, and reliability. Specialized latch head design. Interference free closure for mid-span cuts. Versatile head positioning allows user to get into tight areas easier. FOR COPPER AND ALUMINUM CABLE ONLY. DO NOT CUT STEEL, GROUND ROD, REBAR, OR GUY WIRE. ESG50L11 ESC105L11 PATCUT245CUAL MODEL ESG50L11 ESC105L11 PATCUT245CUAL Weight 9.8 lbs. w/ Battery 22 lbs. w/ Battery 14.5 lbs. w/ Battery Max. Cable Cutting Diameter 2 in. 4 in in. Size 15-3/4"L x 13"H x 3"W 13-3/4"L 18 L x 14.75"H x 3.75"W Battery 18 V 12 V 18 V Head Rotation 350º 350º 180º Cutting Capacities Cu & Al Cable: 2' Communications, Cu & Al Cables: 4' Cu & Al Cable: 2.45 CUTTERS BATTERY HYDRAULIC 61

16 CUTTERS BATTERY HYDRAULIC 62 REC-S640 8 TON CUTTING TOOL WITH 1.6 JAW OPENING The REC-S640 is designed to cut up to 1590 ACSR and regular guy wires and ground rod up to 5/8. The REC-S640 is ideal for aerial bucket work and trench operations. It features a two stage, rapid advance ram for reduced cycle times. This cutter is made for one-handed operation. Simply remove the pin latch, place over cable, reinsert pin, and cut. A built-in bypass will pop off if the material is beyond the cutter s capacity. It is not recommended to cut hardened steel. FEATURES Tested Up to 75kV One Hand Operation Rotational Head Rapid Advance Ergonomically Balanced Ergonomic Pistol Grip Handle Weather Resistant Housing Overload Bypass Protection 5 Year Warranty on Tool, Battery & Charger REC-S TON CUTTING TOOL WITH 2 JAW OPENING The REC-S3550 cuts ACSR, guy wire, wire rope, and ground rod. Powerful and portable with a 2" jaw opening. A latch-type jaw swings open to accept material to be cut. The head can be rotated for positioning of rod or cable. This is our most versatile cutter patterned after our S-55B hand operated cutter. FEATURES Flip-Top Latching Head Tested Up to 75kV One Hand Operation Rotational Head Rapid Advance Ergonomically Balanced Ergonomic Pistol Grip Handle Weather Resistant Housing Overload Bypass Protection 5 Year Warranty on Tool, Battery & Charger MODEL REC-S640 REC-S3550 Weight 13.2 lbs. w/ Battery 23 lbs. w/ Battery Output 8 Ton 13 Ton Size 18.1"L x 11.4"H x 3.1"W 21.5"L x 10.5"H x 3.5"W Cutting Estimates Cutting Capacities With Battery # BP: ACSR: 60 3/4 Wire Rope: 90 5/8 Rebar: 60 3/8 Guy Wire: 40 Wire Rope: 3/4" Rebar (Sc 40, Sc 60), Ground Rod & Guy Wire: 5/8" ACSR: 1590 MCM Cu/Al Cable: 1.5" REC-S640 With Battery # BP: 84 Wire Rope: 60 Rebar, Ground & Anchor Rod and ACSR: 45 Cu & Al Wire: 35 Standard Guy Wire: 3/4" Soft Steel Bolts: 1-1/4" Rebar, Ground & Anchor Rod: 3/4" ACSR and Cu & Al Wire: 2" Standard Guy Wire: 3/4" QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION REC-S3550

17 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION REC-630Y 6.6 TON CUTTING TOOL The REC-630Y was designed to cut ACSR cables up to 336 MCM, as well as 500 MCM copper and aluminum cables up to All cuts are clean with minimal cable distortion, for easy connector installation. The open C type jaw is convenient when reaching out to cut cable. REC-660YC 6.6 TON SCISSOR-TYPE CUTTING TOOL The REC-660YC works well for most underground aluminum cable cutting applications. It was designed to cut copper cables up to 500 MCM and aluminum up to 2 maximum outside diameter. The extra wide jaws make cutting the larger diameter underground cables easier. Because of the larger cutting surface of the blades, the maximum size copper cable that can be cut is 500 MCM. REC-630Y CUTTERS REC-685YC 9 TON SCISSOR-TYPE CUTTING TOOL The REC-685YC is designed to cut copper and aluminum cables as well as lead-sheathed telecommunication cables. The extremely large jaws and scissor-type blades allow for easy cutting of large underground cables. The sidebar handle allows the user to stabilize and balance the tool. This tool also has a built-in bypass cartridge to avoid cutter damage for those cables that are beyond the cutter s capacity. REC-660YC FEATURES Open Scissor Jaw for Easy Cable Insertion Tested Up to 75kV One Hand Operation Rotational Head Rapid Advance Overload Bypass Protection REC-660YC & REC-660YC- For Cu & Al Only MODEL REC-630Y REC-660YC REC-685YC Weight 10.3 lbs. w/ Battery 10.2 lbs. w/ Battery 14.7 lbs. w/ Battery Jaw Opening 1-3/16" 2-1/2 3.3" Size 15.5"L x 12.5"H x 3.1"W 16 L x 12 H x 2.5 W 20"L x 13"H x 3.4"W Output 6.6 Ton 6.6 Ton 9 Ton Cutting Estimates Cutting Capacities With Battery # BP: MCM Cu Bar - DO NOT CUT ACSR MCM Cu MCM Al " O.D. Standard Guy Wire - 3/8" Max. With Battery # BP: MCM Cu MCM Al ACSR - DO NOT CUT Cu MCM Al - 2" O.D. REC-685YC With Battery # BP: MCM Cu MCM Al - 60 ACSR - DO NOT CUT Al & Telecommunications - 3.3" Cu: 1000 MCM Lead Sheath - 2.5" BATTERY HYDRAULIC 63

18 CUTTERS ES20L22 ES20L22 GATOR BATTERY POWERED CUTTING TOOL FEATURES Designed primarily to cut distribution ACSR cable Scissor style blades make it easy to cut short tag ends on tap cables in H-tap connectors Powerful state of the art 18V lithium ion (Li-ion) battery LED light provides the operator with the battery charge and tool maintenance status Cutting head rotates 350 Tool automatically retracts when the cutting cycle is complete ECO TON BATTERY POWERED CUTTING TOOLS FEATURES Lightweight ergonomic design Tested Up to 75kV Rotational Head On Hand Operation Compatible with all Huskie 14.4V Batteries ECO-500 Designed for copper and aluminum conductor only, provides a much cleaner cut then working with non-acsr conductor. BATTERY HYDRAULIC ECO-336 The ECO-336 streamline battery powered cutting tools have a powerful 6 ton output for handling the most difficult of tasks. The ECO-336 is designed for steel core conductor, but also has the added feature of being able to handle copper and aluminum conductor up to 500 MCM. No need for another battery system. This tool operates on the same 14.4 volt battery used in all of the Huskie Robo tools. Just like the rest of our battery powered tools, energized lines will not affect the operation or performance of the tool. MODEL ES20L22 ECO-500 ECO-336 Weight 4.6 lbs. 6.8 lbs. 6.8 lbs. Size 15"L L 3.7 L x H x 2.8 W Cutting Performance Approximately 100/charge Approximately 80/charge Approximately 84/charge Cutting Capacities ECO-336 Cutter Head Opening: 3/4 in. ACSR: 336 KCMIL Guy Strand (Not EHS): 3/4 in. Ground Rod: 3/4 in. Rebar (SCH 60): 3/4 in. Standard Guy Wire: Do Not Cut Aluminum: Up to 1.5 in. Copper: Up to 500 MCM ACSR: Do Not Cut ACSR: 336 MCM Aluminum: Up to 1 in. Copper: 500 MCM Standard Guy Wire: 3/8 in. 64 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

19 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION BATTERIES & CHARGERS CUTTERS CB1820L 18 V 2.0 Ah Li-Ion high power battery CB1840L 18 V 4.0 Ah Li-Ion high power battery ASC30-36 USA CAN Input 115 V / 60 Hz Output V DC / 3.0 A max. CB1430L 14.4 V 3.0 Ah Li-Ion high power battery CFC230N Input 230 V / Hz Output 7,2-18 V DC BP V 2.0 Ah BP V 4.0 Ah CH-94 1 hour charge time for BP-82 & BP Gator Battery 18 V Battery Charger 18 V BT18V PATRIOT IN-LINE Battery, 18.0 V PATCHGR18V Battery Charger, NiMH BATTERIES & CHARGERS M18 REDLITHIUM XC 5.0 Extended Capacity Battery Pack M18 REDLITHIUM 2.0 Compact Battery Pack M18 & M12 Multi-Voltage Charger M18 & M12 Rapid Charge Station 65

20 CUTTERS REL-R-HC REL-R-HC RATCHETING HARD CABLE CUTTER 1-3/16" Capacity, Jaw keeper prevents the jaws from spreading while under heavy load. Shear-cut blades. Ratchet and chain increase cutting pressure as handles open and close. Cuts ACSR, ACAR, hard cable & self supporting telephone cable with minimal distortion. Moderate pressure opens & closes handles. Mechanical advantage over manual cutters. R954-CH REL-R-SC REL-R-SC RATCHETING SOFT CABLE CUTTER Cut Copper & Aluminum cable up to 2 inches, including rubber or lead covered cable. Heavy duty jaw and ratchet design provides mechanical advantage over manual cutters. DO NOT CUT STEEL RATCHETING REL-R-GS REL-R-3/4GS Replacement heads available for quick easy repair. R1500S-CH REL-R-GS RATCHETING GUY STRAND CUTTER 7/16" Capacity, notched blades hold material, while ratchet produces easy, progressive cuts. Cuts EHS guy strand, mild steel rods, bolts, and similar materials. Clean, square cuts with minimal distortion. Mechanical advantage over manual cutters. R-7/16GUY-CH REL-R-3/4GS RATCHETING EHS GUY CUTTER 3/4" Capacity, shear-cut blade holds material in place. Cut EHS guy strand, wire rope, aircraft cable, and hard S.S. cable with minimal crushing or distortion. Mechanical advantage over manual cutters. R-3/4GUY-CH 66 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

21 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION H.K. PORTER CABLE CUTTERS 8790 CS & 8790 FSK - RATCHET TYPE, SOFT CABLE CUTTERS Jaws with shear-cut blades, Special pivoting handle allows cutter head to be opened to maximum width independent of handle position. Cuts copper and aluminum, power and communications cable. Designed to cut conductors with large insulation. Max. handle spread of 22 for working in confined spaces. Increased mechanical advantage over manual cutters CS CUTTERS 8690 FSK - SOFT CABLE CUTTER 2 Capacity, Jaw keeper prevents jaws from spreading while under heavy load. Cuts copper and aluminum communications and power cable in sizes up to 2, including rubber or lead covered cable. Improved H/D jaw design, ratchet mechanism provides up to 5 times mechanical advantage over manual cutters. Cuts all types of copper and aluminum cables up to 2500 MCM CS - RATCHET TYPE, SOFT CABLE CUTTERS Shear-cut blades give fast, smooth, shearing cuts. Cuts copper, aluminum, and rubber covered or lead covered power and communications cable to 3. Ratchet and chain apply increased cutting pressure with opening and closing of handles. Gives increased mechanical advantage over manual cutters FSK 8690 FSK 8690 FH - RATCHET TYPE, HARD CABLE CUTTER 1-3/16" Capacity, Jaw keeper prevents jaws from spreading while under heavy load. Shear-cut blades. Ratchet and chain increase cutting pressure as handles open and close. Cuts hard cable, ACSR, ACAR, and self-supporting telephone cable with minimal distortion. Moderate pressure needed to open and close handles. Can be used effectively in confined spaces. Increased mechanical advantage over manual cutters CK - RATCHET TYPE, GUY STRAND CUTTER 7/16 Capacity, notched shear-cut blades hold material firmly, while ratchet and chain produce easy, progressive cuts. Cuts EHS guy strand, mild steel rods and bolts, and similar materials. Makes clean, square cuts with minimal distortion. Increased mechanical advantage over manual cutters TN - RATCHET TYPE, WIRE ROPE CUTTER 3/4 Capacity, Ratchet-Type jaws with notched shear-cut blades hold and lock material in place. Cuts aircraft cable, EHS guy strand, wire rope, and hard S.S. cable. Cuts all strands with minimal crushing or distortion. Increased mechanical advantage over manual cutters CS 8690 FH 8690 CK 8690 TN RATCHETING MODEL 8790 CS 8790 FSK 8690 FSK 8690 CS 8690 FH 8690 CK 8690 TN Weight 15 lbs. 10-1/2 lbs. 3-1/2 lbs. 12-1/2 lbs. 10-1/2 lbs. 8-3/4 lbs. 13 lbs. Length 27-1/2 in. 27-1/2 in. 27-1/2 in. 29-3/4 in. 29-1/4 in. 28 in. 36 in. Capacity 3 in. Cu/Al 2 in. Cu/Al 2 in. Cu/Al 3 in. Cu/Al 1-3/16 in. ACSR, ACAR 7/16 in. Guy Strand 3/4 in. Aircraft / Hard SS Cable Replacement 8713CS 8713FSK 8613FSK 8613CS 8613FH 8618CK 8613TN Cable Soft Soft Soft Soft Hard Hard Hard 67

22 CUTTERS RATCHETING RATCHET CABLE CUTTER Extra thick blades, ground flat to reduce potential for breakage Ratchet action for heavy-duty cutting Two cutting actions - fast scissor cutting for small cable and insulation Converts automatically to ratchet mode Anti-slip mechanism for positive ratchet action Rubber boot protects ratchet mechanism 757 RATCHET ACSR CABLE CUTTER Extra-thick blades, ground flat to reduce potential for breakage Ratchet action for increased cutting power Two cutting actions - fast scissor cutting for small cable converts automatically to ratchet mode Anti-slip mechanism for positive ratchet action Rubber boot protects ratchet mechanism 758 RATCHET GUY WIRE CUTTER Cuts 1/2 in. Extra High Strength (EHS) & standard guy wire Cuts 1/2 in. (12.7 mm) mild steel rods and bolts Has two cutting actions - single-motion cutting for small cable, ratchet action for heavy-duty cutting Anti-slip mechanism for positive ratchet action RATCHET CABLE CUTTER Simple, one-hand operation Exclusive two-speed ratcheting mechanism adjusts for light/heavy cutting Well-suited for tight working spaces Blades can be opened mid-cycle Available with cushioned handles or with 1000V insulated cushioned handles MODEL Capacity Al & Cu: 1500 KCMIL (MCM) (800 SQ-MM) Max. Use, 1000 KCMIL (MCM) (500 SQ-MM) Frequent Use 954 KCMIL (MCM) ACSR, 1/2 in. Soft Steel Rod 1/2 in. Extra High Strength & Standard Guy Wire, 1/2 in. Mild Steel Rods & Bolts Al : 1000 KCMIL (MCM) (750 SQ-MM) Max. Use, Cu: 750 KCMIL (MCM) (300 SQ-MM) Frequent Use Jaw Size 2 in in. 2 in. Overall Length Replacement Part 27-1/2 in. 29-1/4 in. 27-3/4 in. 11 in Cutter Head Unit (Includes 2 Blades) Cutter Head Unit (Includes 2 Blades) Cutter Head Unit (Includes Blades, Blade Holder, Insert and Hardware) Movable Blade Fixed Blade Type Heavy Duty Ratchet Ratchet Heavy Duty Ratchet Ratchet Weight lbs lbs. 10 lbs lbs. 68 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

23 QUALIT Y I EXPERIENCE PROFESSIONALISM I D E D I C AT I O N CUTTERS I COMPACT RATCHETING CABLE CUTTER Compact, lightweight cutter for confined spaces Ratchet-type jaws with shear-cut blades grip and hold while moderate pumping action cuts cable Leaves no burrs or sharp edges Both blades cut Fiberglass handles with non-slip, plastic grips Cutter has self-lubricating ratchet and only 6 moving parts Note: MCM capacity does not include cable insulation, MCM capacity equates to conductor size only MODEL DESCRIPTION COPPER CABLE ALUMINUM CABLE COMMUNICATION CABLE WEIGHT 6990FS Soft Cable Cutter - 14 in. 500 MCM 795 MCM 1-3/16 in. 3.5 lbs. 6990FSL Soft Cable Cutter - 19 in. 750 MCM 795 MCM 1-3/16 in. 3.5 lbs. MODEL DESCRIPTION SINGLE CORE ACSR THREE CORE ACSR WEIGHT 6990FHL Hard Cable Cutter - 19 in. 653 MCM 336 MCM 3.5 lbs RATCHETING ACSR CABLE CUTTER - HEAVY-DUTY Cuts steel and ACSR Ratchet-action design provides maximum leverage with minimum effort for heavy-duty use Blade-advance knob for fast rotation of the blade to engage the cable or other material being cut, plus a quick-release mechanism allows for removal of the cable or rod before completion of the cut, if desired RATCHETING Not for cutting EHS guy strand or reinforcement rod Ratcheting ACSR Cable Cutter - Heavy-Duty Cuts steel and ACSR Forged, heat-treated, shear-type blades, plus 17" (432 mm) long fiberglass handles with heavy duty grips for comfort and slip resistance MODEL O.A.L. SOFT CABLE-CUTTING MAX. CAP " 2-1/4 (57.2 mm) Dia., 750 MCM (1-3/8 [34.9 mm]) Dia., Cu or Al STEEL CABLE-CUTTING MAX. CAP. WEIGHT 1-1/4 (31.8 mm) Dia. ACSR, ACAR, 7/16 (11.1 mm) Dia. Common Guy Strand, 5/8 (15.9 mm) Dia. Steel Wire Rope, 1/2 (12.7 mm) Dia. Steel Rod (C.R.S. SOFT) 14 lbs & CABLE BENDERS " Cable Bender Durable forged and one-piece steel construction 14 Cable Bender Head is angled 22 for ease in bending cable in tight places Corrosion-resistant, black-oxide finish with heavy-duty double-dipped plastic handle Recommended that two benders be used for easier bends 69

24 CUTTERS RC1000A RC750H RC1000A, RC750H & RC945H RATCHETING CABLE CUTTER Combines a unique design with quality construction to afford speed, ease of use, and safety to the operator. Heavy duty C Jaw long-life ratcheting mechanism Thumb slide release allows rapid opening or closing Single lever allows easy switch from opening to closing Reinforced fiberglass handles with a protective polyvinyl chloride coating Practically half the size of standard ratchet cutters at less than half the weight The large cutting capacity of these tools requires less than 50% of the ratchet opening of standard tools RC954H Spread: 31 inches Blade Opening: 1-7/8 inches Fast Advance OPEN / CLOSE Selector Dial MODEL RC1000A RC750H RC954H Weight 4 lbs. 4 lbs. 4 lbs. Length 19.5 in. 18 in. 23 in. Cut Power Cable Up to 1000 MCM 750 MCM 1000 MCM Cut ACSR Up to Do Not Cut 556 MCM 954 MCM RATCHETING REL-35 REL-750 REL-35, REL-750 & REL-9009 RATCHET CABLE CUTTER These models feature a full ratcheting cycle and release in all cutting positions. Handle locks in closed position for easy storage and transportation. H/D molded plastic handles feature ergo design to provide maximum leverage. Heavy duty handle features a rubber grip, and ergonomic design to maximize cutting leverage. Ratcheting Cable Cutter has been designed to cut a wide range of cable with the convenience of single handed operation. Features a full ratcheting cycle and release in all cutting positions. The handle locks in closed position for storage and transportation. REL-9009 MODEL REL-35 REL-750 REL-9009 Weight 1.5 lbs. 2 lbs. 1.2 lbs. Length 10 in. 9 in in. Max Cap. Cu 1.25 in in. 350 MCM Max Cap. Al 1.25 in in. 500 MCM Max Cap. Hard Drn. Cu. 500 MCM 750 MCM 500 MCM ACSR Do Not Cut Do Not Cut 336 MCM (18/1) 70 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

25 QUALIT Y EXPERIENCE I PROFESSIONALISM I D E D I C AT I O N CUTTERS I RATCHETING CABLE CUTTERS High-leverage ratchet mechanism for one-handed cutting of copper and aluminum cables, leaving no burrs or sharp edges Open jaw design works in confined spaces (Cat. No ) Quick-release lever opens blades in every cutting position (Allows removal of the cable before completion of cut) Holds cable tight and allows, straight cuts with less effort Hardened steel blades for lasting strength and sharpness Plastic covered handles with guards for comfort and grip Locking lever keeps handles closed for easy transport One-year warranty (Cat. No & 63750) Replacement parts available (blades, handles, springs, pawl sets and release plates). WARNING: DO NOT CUT STEEL or ACSR Klein non ratcheting cutter, side cutters, and diagonal cutters are in the hand tool section. MODEL OVERALL LENGTH MAX. CABLE CAPACITY (COPPER) MAX. CABLE CAPACITY (ALUMINUM) MAX. CABLE CAPACITY (COMMUNICATION CABLE) WEIGHT /4 in. 400 MCM (185 mm2) 600 MCM (300 mm2) 1-1/8 in. (28.6 mm) 1.3 lbs /2 in. 600 MCM (300 mm2) 750 MCM (400 mm2) 1-1/8 in. (28.6 mm) 2.0 lbs /8 in MCM (500 mm2) Frequent Use: 750 MCM (400mm2) 1000 MCM (500 mm2) Frequent Use: 750 MCM (400mm2) 2-1/16 in. (52.4 mm) 1.8 lbs. ACSR RATCHETING CABLE CUTTER RATCHETING & 63800ACSR High-leverage ratcheting mechanism for easier cutting Quick-release lever opens blades easily in every cutting position (Allows removal of the cable before completion of cut) Hardened steel cutting blades for long lasting strength and sharpness Tools can be locked when not in use 63800ACSR Cat. No ACSR features cutting inserts that are easily replaced by simply removing 3 screws per blade Replacement parts available (blades, handles, springs, pawl sets and release plates). MODEL OVERALL LENGTH MAX. CABLE CAPACITY (COPPER) MAX. CABLE CAPACITY (ALUMINUM) MAX. CABLE CAPACITY (ACSR) MAX. CABLE CAPACITY (GUY STRAND) WEIGHT /4 in. 400 MCM (185 mm2) 600 MCM (300 mm2) 336 MCM (170 mm2) 1.3 lbs ACSR 13-1/4 in. 1 in. (25.4 mm) 1-1/4 in. (31.8 mm) 477 MCM (273 mm2) 1/2 in. (12.7 mm) 2.0 lbs. 71

26 CUTTERS CONDUCTOR CUTTERS WITH INSULATED HANDLES INSULATED HANDLE CABLE SLICERS For use on soft copper and all aluminum cable only Not to be used on steel or ACSR cable Replaceable fiberglass handles are electrically tested The drop forged cutter blades and fiberglass handles are designed for easy field replacement Water repellent case for storage Slicing action of cutter blade provides flush, burr-free conductor ends ACSR CABLE CUTTER For cutting ACSR Cable, Soft Wire, Hard Wire Replaceable fiberglass handles with blade Handles filled with unicellular foam core Smooth shear action cutter assures easy installation of splicing sleeves MODEL Handle FG FG FG Capacity 600 MCM Al 350 MCM Cu 1000 MCM Al 500 MCM Cu ACSR: 5/8" dia Cu: 5/8" dia. 350 MCM Al: 1" dia. 750 MCM Length 20-1/2 in. 28-3/4 in. 31 in. Weight 3 lbs. 5.5 lbs. 6 lbs. MANUAL INSULATED For Soft Wire (Available with Long or Short Handles) C C CUTTERS FOR ALUMINUM & COPPER OR ACSR Choice of insulated long or short handles on cutters for soft wire, and insulated long handles on cutters for ASCR Chance orange 1-1/2" diameter Expoxiglas handles have black rubber cushion grips Shear-type blades cut without deforming cable Heat-treated tool-steel cutter heads are same as Chance Ratchet Cable Cutters Order replacement or spare cutter heads as separate items, below Note: ACSR head is not for use with 15-1/2" handles Soft-wire head must not be used to cut ACSR Optional: Storage bags to fit short or long cutters Storage bags are heavy-duty yellow vinyl-impregnated nylon cloth Cutters are designed for energized applications Users must wear rubber gloves and observe all applicable working clearances when cutting energized conductors 72 For ACSR Wire (Available with Long Handles only) C MODEL C C C Length in. 35 in. 33-1/2 in. Max. Capacity 600 MCM A.A./350 MCM Cu MCM A.A./500 MCM Cu MCM ACSR Weight 4 lbs. 5-1/2 lbs. 5 lbs. Replacement Cutterhead 1413C 0013C 0113C QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION

27 EXPERIENCE I PROFESSIONALISM I D E D I C AT I O N NOTE DO NOT CUT STEEL REL MCM - SLICER REL-1000 CUTTERS I QUALIT Y 1000 MCM - CABLE SLICER REL MCM - CABLE SLICER MODEL REL-500 REL-1000 REL-2000 REL- 500, 1000, CABLE SLICERS Handle FG FG Steel Cap. 500 MCM 1000 MCM 2000 MCM The Reliable line of heavy duty cable slicers will cut aluminum, copper and communications cable from 500 MCM to 2,000 MCM with minimum cable distortion and long service life. Length 21 in. 31 in. 36 in. Weight 3.5 lbs. 7.1 lbs lbs & 63035SC UTILITY CABLE AND ROPE CUTTERS Forged steel with black-oxide finish for long life Shear-type hook jaws grab and hold cable while shear-cutting action makes clean cuts Beveled tips for positive mating Hinge bolt with pin-set nut for proper blade tension This handy, economical tool handles most cable-cutting jobs with ease. Special high-leverage design gives it amazing cutting capability for its size. Cable-gripping, shear- type jaws cut up to 4/0 aluminum (NOT ACSR) up to 2/0 soft copper up to 100-pair, 24-gauge communication cable. Makes clean, efficient cuts. Can be carried in tool pouch. Ideal for working in confined spaces. Tough, comfortable, red plastic-dipped handles. Not designed for cutting steel or ACSR. Length: 9-1/2". MANUAL HIGH-LEVERAGE CABLE CUTTER 63035SC MODEL SC Overall Length 16-1/4" 18" 9-1/2" Max. Cutting Cap. MCM Cable 350 Cu, 350 Al 9/32" Wire Rope & Cables 4/0 Al, 2/0 Soft Cu, 100-Pair 24 AWG Comm. Cable Weight 1.7 lbs. 2 lbs oz

28 CUTTERS Steel handles with rubber grips 0190MC CENTER CUT CUTTERS WITH STEEL HANDLES Cuts soft, medium, or hard materials. (Max.: Brinell 400/Rockwell C42) Drop-forged, precision ground, alloy tool steel jaws with center-cut blades Lockplate keeps jaws from loosening Toggle joints turn 50 lbs. hand pressure to 4,000 lbs. cutting pressure Screw-type adjustment realigns edges MODEL 1490MC 0090MC 0190MC 0290MC 0390MC 0590MC Length 14 in. 18 in. 24 in. 30 in. 36 in. 42 in. Soft & Medium 5/16 in. 3/8 in. 7/16 in. 1/2 in. 9/16 in. 11/16 in. Hard 3/16 in. 1/4 in. 5/16 in. 3/8 in. 7/16 in. 1/2 in. Replacement Cutterhead 1413C 0013C 0113C 0213C 0313C 0513C CENTER CUT CUTTERS W/ FIBERGLASS HANDLES Fiberglass handles with rubber grips 0190FC Cuts soft, medium, and hard metals Strong, lightweight, fiberglass handles. Max. Material Hardness: Brinell 400/Rockwell C42 The lockplate keeps jaws from loosening Toggle joints turn 50 lbs. of hand pressure to 4,000 lbs. of cutting pressure Screw adjustment realigns edges MODEL 0090FC 0190FC 0290FC 0390FC Length 18-1/4 in. 24-1/2 in. 30-1/2 in. 36-1/2 in. MANUAL Fiberglass handles with rubber grips Soft & Medium 3/8 in. 7/16 in. 1/2 in. 9/16 in. Hard 1/4 in. 5/16 in. 3/8 in. 7/16 in. Replacement Cutterhead 0013C 0113C 0213C 0313C HIGH TENSILE STEEL BOLT CUTTERS WITH INSULATED FIBERGLASS HANDLES Suitable for cutting hard material Short cutting edge for high tensile steel, bolts, wire, rods, chain links, and case hardened chains Handles are filled with unicellular foam core MODEL MFG HANDLE O.A.L. SOFT MEDIUM HARD Hastings 12 in. 20 in. 3/8 in. / 10 mm 5/16 in. / 8 mm 9/32 in. / 7 mm (924) Hastings 16 in. 24 in. 3/8 in. / 10 mm 5/16 in. / 8 mm 9/32 in. / 7 mm Hastings 14 in. 22 in. 3/8 in. / 10 mm 5/16 in. / 8 mm 9/32 in. / 7 mm Hastings 21 in. 30 in. 1/2 in. / 13 mm 11/32 in. / 9 mm 5/16 in. / 8 mm Hastings 26 in. 36 in. 5/8 in. / 16 mm 3/8 in. / 10 mm 11/32 in. / 9 mm C-18F Eagle Line 12 in. 18 in. 3/8 in. / 10 mm 3/8 in. / 10 mm 3/8 in. / 10 mm C-24F Eagle Line 16 in. 24 in. 3/8 in. / 10 mm 3/8 in. / 10 mm 3/8 in. / 10 mm 74 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION