SPECIFICATION 三洋精密株式会社. Page 1/8. Version: 0.2 Model name: NRS-2574 (i) Date: Date Originator Version Detail spec changes
|
|
- Marshall Roberts
- 5 years ago
- Views:
Transcription
1 Page 1/8 Date Originator Version Detail spec changes T. Takagi 0.1 Reference specification T. Takagi 0.2 Add recommended reflow profile SANYO SEIMITSU CO., LTD. 1771,NAKAMARUKO UEDA-SHI NAGANO-KEN JAPAN Approval Exam Check Design
2 Page 2/8 This specification is only applicable to NRS-2574 (i) 1. Environmental characteristics 1-1 Operating temperature ranges -30 C ~ +70 C 1-2 Storage temperature ranges -40 C ~ +85 C 2. Mechanical characteristic A detailed mechanical drawing for the vibration motors shall be provided with dimensions And tolerances. 2-1 Pull out strength of counter weight and shaft 30 N Min 2-2 Axial play of shaft 0.3 mm Max 2-3 Counter weight density 17g/cc Min 2-4 Total weight Approximately 1.5g 2-5 Rotating direction CW/CCW 2-6 Mechanical noise of motor operating at rated speed 45 db Max A-weighting (Measured distance 10 cm, see Appendix 1.) 2-7 Functional dimensions M012574**, Appendix Bracket material SPCE 2-9 Terminal material C7521R-H 2-10 Bracket and Terminal undercoating Ni plating 2-11 Bracket and Terminal surface finish 2~5 microns, Sn plating 3. Electrical characteristics Principle measurement: 5 C ~35 C; relative humidity 30%~90%. For abnormalities: 20 C +/- 2 C, 65% +/- 5%. Measurements with test jig 3-1 Voltage rating, nominal operating 1.3 V Voltage at specified rotating speed 3-2 Operating voltage (min/max) 1.1 V ~ 1.5 V 3-3 Current rating at specified rotating speed 105 ma Max 3-4 Starting current at rated voltage 130 ma Max 3-5 Starting voltage at rated load 1.1 V Max 3-6 Insulation resistance and voltage breakdown 1 M ohm Min 3-7 Max transient voltage 6.0V 3-8 Terminal resistance /- 2 ohm (2/3 poles) 3-9 Operating speed at rated voltage / rpm
3 Page 3/8 4. Environmental requirements and testing. 5. Marking of the parts Following markings must be placed in parts whenever possible in order listed: 1. Version marking 2. Manufacturing date code 3. Part number. Marking of the part number must be agreed separately and it must be defined in supplier specification or in supplier drawing. Lot No. Indication Lot No. is indicated by print as below : Day : 1~V Month : 1~9,10(X),118Y),12(Z) ( Year : day print A B C D E F G day print H I J K L M N O P Q R S T U V
4 Page 4/8 Packing Condition 6-1 Smallest packing reel packing dimension
5 Page 5/8 6-3 Final packing Bubble sheet (Top) Corner Pad protector x 4 a. 700pcs / 1 reel x 6 reel =4,200pcs Upper side: Counter Weight Bubble sheet (Bottom) (350) (250) Double wall corrugated cardboard (350)
6 7. Warranty Page 6/8 8. Handling 8-1 Low molecule silicon compound, which is included in silicon products, may cause electrical failure. Verify sufficiently when you use silicon products. 8-2 Verify sufficiently that adhesives or seals do not outgas corrosive gases that harm the motor. Cyano adhesive or sulfur gases will cause the motor failure. Also, if an adhesive is used to install the motor, ensure the adhesive does not flow into motor (especially bearing part.) 8-3 Ambient temperature and humidity during motor operation affect performance and product life. Do not store motor in locations subject to high temperatures and high humidity or in corrosive gas environment. Below are recommended storage conditions. Temperature: 5 C ~ +35 C, humidity: 30% ~ 90%. 9. Critical characteristics 10. Others 10-1 Whatever item not stated in this specification will not be guaranteed Do not subject the motor under locked condition for long hours Do not exert pressure by pushing the current terminals towards the direction of the internal motor Out-going test data will be attached (n-35) for Loaded rotation Loaded current Lock current (Starting current) Starting voltage 10-5 Recommended Reflow profile Reflow specification 245 Peak temperature: Rate of temperatuer rise: 1~4 /sec Rate of temperatuer rise: 2~4 /sec 120 Pre-heat time: 70±20sec Above 220 holding time: 30±10sec
7 Page 7/8 Appendix 1 ELASTIC BAND VIBRA MICROPHONE 100mm JIG Figure mm 100mm Figure 2. Figure 3.
8 Page 8/8 Appendix 2
SPECIFICATION 三洋精密株式会社. Page 1/10. Version: 0.1 Model name: NRS-3388(i) Date:
Page 1/10 Date Originator Version Detail spec changes 11.06.13 T. Takagi 0.1 Preliminary spec written SANYO SEIMITSU CO., LTD. 1771,NAKAMARUKO UEDA-SHI NAGANO-KEN JAPAN Approval Exam Check Design Page
More informationSpecifications: Gear Motor, 12GN 0348
1. Product Description Model Number: Gear Motor, 12GN 0348 External appearance will be judged with the naked eye and will be free of scratches and abrasions 2. Motor Characteristics NA1S RA1S NA2S NA3S
More information1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass)
Thick Film Chip Resistor CR Series Construction 1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass) 4 Barrier
More information0.6mm Pitch Stacking Height 3mm to 16mm Connectors
.6mm Pitch Stacking Height 3mm to 16mm Connectors FX8/FX8C Series FX8 Series FX8C Series Note: that FX8 series and FX8C series are not mated with each other. Features 1. Stacking Height: 3mm to 16mm Stacking
More informationCurrent Sensing Resistor Metal Foil Type >SMF Series
Page: 1 of 6 General Chip size from 0603 to Resistance value from 3mΩ to 200mΩ Low thermal EMF. Low TCR. Lead free, RoHS compliant for global applications and halogen free Application Switching model power
More informationCOMPACT FLAT SIZE FOR AUTOMOTIVE
PACT FLAT SIZE FOR AUTOMOTIVE RELAYS RoHS compliant FEATURES Compact flat type Flat size enables it to be built-in switch units. PC board terminal type: 9.5 mm.374 inch Surface-mount terminal
More informationApproval sheet. WLCM0603 WLCM1005 Multi-Layer Ceramic High Frequency Inductors. *Contents in this sheet are subject to change without prior notice.
WLCM0603 WLCM1005 Multi-Layer Ceramic High Frequency Inductors *Contents in this sheet are subject to change without prior notice. Page 1 of 11 ASC_WLCM Series_V7.0 Jul. 2017 FEATURES 1. Ceramic structure
More informationCOMPACT FLAT SIZE FOR AUTOMOTIVE
PACT FLAT SIZE FOR AUTOMOTIVE RELAYS RoHS compliant FEATURES Compact flat type Flat size enables it to be built-in switch units. PC board terminal type: 9.5 mm.374 inch Surface-mount terminal
More informationAnti-Surge Thick Film Chip Resistors
FEATURES EXCELLENT ANTI-SURGE & ANTI-SULFUR CHARACTERISTICS AEC-Q200 QUALIFIED RATED POWER UPGRADE IN SMALLER PACKAGE SIZE AVAILABLE IN ± TOLERANCE BOTH FLOW SOLDER AND REFLOW SOLDERING ARE APPLICABLE
More informationSurface Mount Fuses 1206 Size >Fast Acting>S1206-FA-8A~15A. General
Page: 1/ 6 General Fastacting 3.10mm 1.55mm physical size Thick film manufacturing method, ceramic substrate, silver fusing element -55 ~125 operating temperature Excellent environmental integrity RoHS
More information0.6mm Pitch Stacking Height 3mm to 16mm Connectors
.6mm Pitch Stacking Height 3mm to 16mm Connectors FX8, FX8C Series FX8 Series FX8C Series Note: that FX8 series and FX8C series are not mated with each other. Features 1. Stacking Height: 3mm to 16mm Stacking
More informationCYG Wayon Circuit Protection CO., LTD.
CATALOG (2014) CYG Wayon Circuit Protection CO., LTD. CONTENTS Surface Mount Fuses 1206F Series. 2 0603F Series.5 1206S Series.8 0603S Series.11 Applications..14 Product Identification...14 Reliability
More informationJune 26, 2006 DIELECTRIC CERAMIC DUPLEX FILTER SPECIFICATION 1 OF 6 SPECIFICATION ITEM: DIELECTRIC CERAMIC DUPLEX FILTER PART NUMBER: CFDM
June 26, 2006 DIELECTRIC CERAMIC DUPLEX FILTER SPECIFICATION 1 OF 6 SPECIFICATION ITEM: DIELECTRIC CERAMIC DUPLEX FILTER PART NUMBER: CFDM-0902094710 Application: GSM 900 Duplexer ISSUED CHECKED CHECKED
More informationContent (RF Inductors) Multi-Layer High Frequency Inductors (IQ & HI Series) Cautions... 18
Content (RF Inductors) Multi-Layer High Inductors (IQ & HI Series)... 2 Ordering Code... 2 Standard External Dimensions... 3 High Q Type (IQ Series)... 4 Standard Type (HI Series)... 5 Testing Condition
More informationGas Discharge Tube (GDT) Products CG/CG2 Series. CG/CG2 Series
Description Littelfuse highly reliable GDTs provide a high degree of surge protection in a small size ideal for board level circuit protection. GDTs function as switches which dissipate a minimum amount
More information1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass)
Thick Film Chip Resistor CR Series Construction 1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass) 4 Barrier
More informationMVR G. Size: Unit:mm. Type Length(L) Width(W) High(H) Termination(L1) ± ± (max) 0.40±
1 Electrical Characteristics 1.1 Technical Data Symbol Value Unit Maximum allowable continuous AC voltage*1 V RMS 50.0 V Maximum allowable continuous DC voltage V DC 65.0 V Varistor voltage Measured*2
More informationORDER INFORMATION L-KLS6-MVR G
istors Varistor s L-KLS6-MVR3220-431G 3220 Varistor s,430v,39pf 1 Electrical Characteristics 1.1 Technical Data Symbol Value Unit Maximum allowable continuous AC voltage*1 V RMS 275.0 V Maximum allowable
More informationMulti-Layer Power Inductors (IP Series)
Multi-Layer Power Inductors (IP Series) For DC/DC Converter Application ORDERING CODE IP R M P S 9 PRODUCT CODE IP : Multilayer Power Inductor (Lead Free) DIMENSION (L X W) Code Dimension EIA. x. mm. X.
More informationNo. P-KAB-001 DATE PRODUCTS DATA SHEET MICRO FUSE. Type KAB. UL/cUL approved File No.E17021 RoHS COMPLIANT LEAD FREE
No. P-KAB-00 DATE 007-0 PRODUCTS DATA SHEET UL/cUL approved File No.E70 RoHS COMPLIANT MICRO FUSE Type KAB LEAD FREE Size 608/0 Type KAB micro fuse is designed for circuit protection against excessive
More information1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass)
Anti-Sulfur SMD chip resistor ST Series Construction 1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass) 4
More information0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors FH30 Series Strong actuator construction Features 1. Strong actuator retention Actuator will not be dislodged
More informationFrelTec GmbH. Wire Wound Ceramic Chip Inductors SMD
GmbH Mathildenstr. 10A 82319 Starnberg Germany Wire Wound Ceramic Chip Inductors SMD 8/2/2017 1/15 GmbH www.freltec.com SPECIFICATION Part Number 091 02 * 101 * J * S * T05 ** _ Type Size Value Toleranc
More informationHigh Power Low Ohm Chip Resistors. Size W, W, /2W
WW25P, WW20P, WW12P ±1%, ±5% 47mΩ~976mΩ High Power Low Ohm Chip Resistors Size 2512 2W, 2010 1W, 1206 1/2W *Contents in this sheet are subject to change without prior notice. Page 1 of 7 ASC_WW25P-20P-12P_V08
More informationAnti-Surge Thick Film Chip Resistors
FEATURES EXCELLENT ANTI-SURGE CHARACTERISTICS AEC-Q200 QUALIFIED RATED POWER UPGRADE IN SMALLER PACKAGE SIZE MEETS +85 C/85%RH TEST 000 HOURS MEETS CLIMATE CATEGORY (IEC 60068): 55/55/56 AVAILABLE IN ±
More information1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass)
Thick Film Chip Resistor CR Series Construction 1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass) 4 Barrier
More informationPLED Ultra Low Holding Current Series
RoHS Description Agency Approvals This PLED ultra-low holding current series exhibits a low holding current parameter that makes it compatible with LED lighting strings. The series provide a switching
More information1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass)
Thick Film Chip Resistor CR Series Construction 1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass) 4 Barrier
More informationR Z18 Series : SMB CARLOCK
.. pn ao TECHNICAL DATA SHEET 1 / 7 EDGE CARD PIN IN PASTE VERSION All dimensions are in mm. COMPONENTS MATERIALS PLATING (µm) BODY CENTER CONTACT OUTER CONTACT INSULATOR GASKET OTHERS PARTS ZINC ALLOY
More informationProduct Data Sheet 4184 NXHH
The engineer's choice 4184 NXHH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating
More information0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors
0.3 or mm pitch, 3 mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors FH30 Series Strong actuator construction Enclosed shaft of the actuator prevents it from dislocation Features
More informationNov 7, 2006 DIELECTRIC CERAMIC FILTER SPECIFICATION 1 OF 9 SPECIFICATION ITEM: DIELECTRIC CERAMIC FILTER PART NUMBER: CF
Nov 7, 2006 DIELECTRIC CERAMIC FILTER SPECIFICATION 1 OF 9 SPECIFICATION ITEM: DIELECTRIC CERAMIC FILTER PART NUMBER: CF-19100328 4/14/06 Added recommended PCB layout and plots. 6/2/06 Added Tape and Reel
More informationTECHNICAL SPECIFICATION OF THERMAL PROTECTOR, ST-22
Preventing hazards due to overheating worldwide. SEKI is always by your side. TECHNICAL SPECIFICATION OF THERMAL PROTECTOR, ST-22 1. APPLICATION SCOPE ST-22 is an Automatic Reset Thermal Protector and
More informationMetal Film MELF Resistors
FEATURES SURFACE MOUNT IN SIZES 0102 (0805), 0204 (1406) AND 0207 (2410) AVAILABLE IN PRECISION TOLERANCE AND TC (TO ±0.1% TOL. AND ±10PPM TC) ALL SIZES ARE AVAILABLE IN TAPE/REEL FOR AUTOMATIC MOUNTING
More informationProduct Data Sheet DV4118 N
The engineer's choice DV4118 N INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating
More informationSurface Mount Fuses 0603Size> Fast Acting > S0603-F Series
Page:1 of 6 General Fast Acting 1.6mm 0.8mm physical size Thick film manufacturing method, ceramic substrate, silver fusing element -50 ~125 operating temperature Excellent environmental integrity RoHS
More informationMCF3 DC86V11CT Inrush-withstand
RoHS Pb Dimensions and construction: (mm) Case: Cover: Terminal substrate metal: Terminal primary plating: Terminal surface plating: Adhesive: Marking: Ceramic Ceramic Copper t=0.1 mm Nickel plated copper,
More informationSpezifikation für Freigabe / specification for release
Artikelnummer / part number : 82550200 Datum / Date : 31.07.06 description : 0805 SMD VARISTOR Lead Free SMD size: 0805 ROHS Compliant A Mechanische Abmessungen / dimensions : SIZE SIZE W L T a 0402 0.5
More informationReference Only. 1. Scope This reference specification applies to LQM2MPN_G0L series, Chip Coil (Chip Inductors).
Spec No. JELF243B-22L-1 P1/9 CHIP COIL (CHIP INDUCTORS) LQM2MPN GL REFERENCE SPECIFICATION 1. Scope This reference specification applies to LQM2MPN_GL series, Chip Coil (Chip Inductors). 2. Part Numbering
More information0.5mm Pitch, 5.8mm above the board, vertical connectors for FPC
Features 0.5mm Pitch, 5.8mm above the board, vertical connectors for FPC FH40 Series 1. Reduction in connection man-hours (30% reduction compared to our conventional item) Our unique actuator form enables
More informationSolidMatrix 1206 Fast Acting Surface Mount Fuses
SolidMatrix 1206 Fast Acting Surface Mount Fuses Features: Multilayer monolithic structure with glass ceramic body and silver fusing element Silver termination with nickel and pure-tin solder plating,
More informationSurface Mount > 1210L Series. Description. Features. Applications. Maximum Time To Trip Current (A) P d typ. (W) Time (Sec.)
1210L Series RoHS Description The 1210L Series PTC provides surface mount overcurrent protection for applications where space is at a premium and resettable protection is desired. Features Agency Approvals
More informationFeatures. Non Isolated Power Module ROF-78E ROF-78E - SMD-R. DC/DC Converter
Features Low profile 4.mm Low cost Wide input range (5V - 36V) Short circuit protection Casellated connections DC/DC Converter Description The is a switching regulator with a wide input voltage range,
More informationWW25W, WW20W, WW10W, WW12W, WW08W, WW06W
WW25W, WW20W, WW10W, WW12W, WW08W, WW06W ±1%, ±5% Thick Film Power Low Ohm Chip Resistors RoHS Exemption free and Lead free Size 2512, 2010, 1210, 1206, 0805, 0603 *Contents in this sheet are subject to
More informationProduct Data Sheet 4184 NGX
The engineer's choice 4184 NGX INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationRefer to CATALOG NUMBERS AND RATING. Fusing within 1 min if the current is 200% of rated current. K A B N A
TYPE KAB Type KAB micro fuse is designed for circuit protection against excessive current in portable electronic equipment, electronic circuit around battery, etc. because the demand for high capacity
More informationMeiLong Electronic Co.,Ltd. Lead Free Thin Film Chip Fuse. 1. Scope. 2. Construction. 3. Type Designation. Over Coat Conductor.
Lead Free Thin Film Chip Fuse Page 1/20 1. Scope This specification applies for the Lead-Free fuse se ries of thin film chip fuse made by ML. 2. Construction Over Coat Conductor Sn Plating Ceramic Substrate
More informationMetal Alloy Low-Resistance Resistor Specifications
Page 1 of 14 Metal Alloy Low-Resistance Resistor Specifications March 2010 Specification Number:GCT-SPEC-011-11 Issued Date:2010/03/01 Page 2 of 14 1. Scope: 1.1 This specification is covered following
More informationHIGH SPEED MEZZANINE PRODUCT SPECIFICATION
OARD TO OARD CONNECTOR 75005 Receptacle Assembly 75003 Plug Assembly Table of Contents 1.0 Scope 2.0 Product Description 3.0 Applicable Documents and Specifications 4.0 Ratings 5.0 Performance 5.1 Qualification
More informationSurface Mount Fuses 0603Size> Slow Blow> S0603-S Series
Revision:F Page:1 of 6 General Slow Blow 1.6mm 0.8mm physical size Thick film manufacturing method, ceramic substrate, silver fusing element -50 ~125 operating temperature Excellent environmental integrity
More informationSurface Mount Fuses 0603Size> Slow Blow> S0603-S-5.0A
Page: 1 of 6 General Slow Blow 1.6mm 0.8mm physical size Thick film manufacturing method, ceramic substrate, silver fusing element -50 ~125 operating temperature Excellent environmental integrity RoHS
More informationSurface Mount > 0603L Series. Description. Features. Applications. Maximum Time To Trip Current (A) P d typ. (W)
0603L Series RoHS Description The 0603L Series PTC provides surface mount overcurrent protection for applications where space is at a premium and resettable protection is desired. Features Agency Approvals
More informationSPECIFICATION FOR APPROVAL INDEX
SPECIFICATION FOR APPROVAL INDEX COVER PAGE INDEX. 0 SHAPES & DIMENSION. 1 PART NUMBER CODE 2 PRODUCT DETAIL 3-5 REEL DIMENSIONS 6 REEL PACKAGING QUANTITY 6 RELIABILITY TEST AND CONDITIONS 7 RECOMMENDED
More informationMCF3 25CT Inrush-withstand
RoHS Pb Dimensions and construction: (mm) Case: End-cap substrate metal: End-cap primary plating: End-cap surface plating: Adhesive: Marking: Ceramic Copper t=0.25 mm Nickel plated, 0.5 μm or more Tin
More informationMulti-Layer Power Inductors (IP_L Series)
Multi-Layer Power Inductors (IP_L Series) For Choke Application ORDERING CODE IP 2012 2R2 M P L 9 PRODUCT CODE IP : Multilayer Power Inductor (Lead Free) DIMENSION (L X W) Code Dimension EIA 1608 1.6 x
More information74 ( ) 127 ( ) A [0,315] 2,20 [0,079] [0,087] 1,60 [0,063] Land Pattern
A FEATURES Shielded Construction with very low DCR Heating Current rating up to 17.9 Amps Saturation Current rating up to 7.5 Amps (based on only 10% inductance drop) Inductance up to 1mH for all case
More informationHigh Power Chip Resistors Size W, W, /2W
WF25P, WF20P, WF12P ±1%, ±5% 0Ω,1Ω~1MΩ High Power Chip Resistors Size 2512 2W, 2010 1W, 1206 1/2W Customer : Approval No : Issue Date : Customer Approval : Page 1 of 7 WF25P, WF20P, WF12P, Ver.8 Jul.2010
More informationProduct Data Sheet 4414/2H
The engineer's choice 4414/2H INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationOrdering Information. Text Surface-Mounting Signal Relay G6K
Surface-Mounting Relay with the World s Smallest Mounting Area and a Height of Only 5.2 mm ROHS compliant. Sub-miniature model as small as 5.2 (H) x 6.5 (W) x 10 (L) mm is ideal for high-density mounting.
More informationReference Only. *B: Bulk packing also available. Inductance. Tolerance M:±20% N:±30% 0.150±25% 1.0 * * N:±30% 0.23±25% 0.8 *2 0.
CHIP COIL (CHIP INDUCTORS) LQM21PN GRD REFERENCE SPECIFICATION P.1/9 1. Scope This reference specification applies to LQM21PN_GR series, Chip Coil (Chip Inductors). 2. Part Numbering (ex) LQ M 21 P N 1R
More informationRefer to CATALOG NUMBERS AND RATING. Fusing within 1 min if the current is 200% of rated current. K A B N A
TYPE KAB (P-KAB-E004) Type KAB micro fuse is designed for circuit protection against excessive current in portable electronic equipment, electronic circuit around battery, etc. because the demand for high
More information0.4 mm Contact Pitch, 1.2 mm above the board, Flexible Printed Circuit ZIF Connectors
.4 mm Contact Pitch,. mm above the board, Flexible Printed Circuit ZIF Connectors FH 7 Series FPC thickness:.±. mm. mm Height, actuator fully closed. (54 pos. shown) Overview Continuous miniaturization
More informationMULTILAYER CHIP VARISTORS
Feature Varistor Voltage from5v to 100V Fast response time Low leakage current High surge current ability Bidirectional clamping, high energy Wide Operating temperature range from -55-125 Suitable for
More informationPressure sensor with built-in amplification and temperature compensation circuit
sensor with built-in amplification and temperature compensation circuit PS-A PRESSURE SENSOR (built-in amplification and temperature compensating circuit) NEW FEATURES 1. Contains built-in amplification
More informationFeatures. Samples. I max (A) P d. typ. (W)
0805L Series RoHS Description The 0805L Series PTC provides surface mount overcurrent protection for applications where space is at a premium and resettable protection is desired. Features Agency Approvals
More information0.3 mm Pitch, 1.0 mm Height FPC Connector
0.3 mm Pitch, 1.0 mm Height FPC Connector FH26 Series Space saving(51 pos. shown) 1.0mm 3.2mm.8mm Metal fittings do no protrude outside of the connector body Features 1. Low-profile 0.3 mm pitch FPC connector
More information1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass)
Anti-Sulfur SMD Array Chip Resistor STA Series Construction 1 Alumina Substrate 5 External Electrode (Sn) 2 Bottom Electrode (Ag) 6 Resistor Layer (RuO 2 ) 3 Top Electrode (Ag/Pd) 7 Primary Overcoat (Glass)
More informationDear Customer, Terms & Conditions for last Time Buy. Best Regards. Meng Wang. Product Manager, Tel: EXT 7955
Littelfuse, Inc. 8755 West Higgins Road, Suite 5 Chicago, IL 6631 USA (773) 628-1 7.1,218 RE: LFPCN41214 From: Littelfuse Product Management Team Dear Customer, Please be aware that Littelfuse is discontinuing
More informationSurface Mount Aluminum Electrolytic Capacitors NACEW Series
FEATURES CYLINDRICAL V-CHIP CONSTRUCTION WIDE TEMPERATURE -55 ~ +105 O C DESIGNED FOR REFLOW SOLDERING MEETS THE REQUIREMENTS OF AEC-Q200* *Contact NIC for supporting test data CHARACTERISTICS Rated Voltage
More informationProduct Data Sheet 624 NR. The engineer's choice
Product Data Sheet 624 NR Product Data Sheet 624 NR The engineer's choice Product Data Sheet 624 NR 624 NR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data...
More informationS J
1. Part Number Identification SPECIFICATION Brightek (Europe) Limited S01-2220 - 240 250 J Series Name Inner Code Size 1206~3220 250 250 = 25 10 0 V=25J 1R5 1R5 = 1.5J Breakdown Voltage 240 = 24 10 0 V=24V
More informationPower Inductors (IP Series)
Multi-Layer Power Inductors (IP Series) ORDERING CODE... 1 Standard External Dimensions... 2 Power Inductor for Choke (L Type)... 3 Power Inductor for DC/DC converter (S Type)... 4 Testing Condition &
More informationData sheet SMD Wire Wound Chip Inductor WL Series
Data sheet SMD Wire Wound Chip Inductor W Series Scope -Ceramic body and wire wound construction provide highest s available.. Features -Ceramic base provide high -Ultra-compact inductors provide high
More informationSpecification. N1206 F Series. Approved by. Date of Establish : (Ref. No : 1206 F_Rev.2)
Specification Product Type SMD(Micro) Fuse N1206 F Series Approved by Date of Establish : 2012.11.01(Ref. No : 1206 F_Rev.2) 1. Scope This specification covers the detail requirements for SMD Micro fuse
More informationGas Discharge Tubes SL1002A Series
SL12A Series SL12A Series RoHS Agency Approvals AGENCY AGENCY FILE NUMBER E128662 2 Electrode GDT Graphical Symbol Additional Information Description The Broadband Optimized SL12A series has been especially
More informationReference Only. Inductance Frequency (μh) Tolerance Typ Max (MHz min.) 85 *
P.1/10 CHIP COIL (CHIP INDUCTORS) LQM2HPN G0L REFERENCE SPECIFICATION 1. Scope This reference specification applies to LQM2HPN_G0 series, Chip Coil (Chip Inductors). 2. Part Numbering (ex) LQ M 2H P N
More informationDescription. Applications
3.5x2.8mm SURFACE MOUNT LED LAMP Features Industry standard PLCC-2 package. High reliability LED package. Wide viewing angle. Single color. Suitable for all SMT assembly and solder process. Available on
More informationDatasheet RS Pro RS Series Thick Film Surface Mount Resistor 0402 Case 402Ω ±1% 0.063W ±100ppm/ C RS Stock No:
Datasheet RS Pro RS Series hick Film Surface Mount Resistor 0402 Case 402Ω ±1% 0.063 ±100ppm/ C RS Stock No: 716-8721 Product Details RS Pro 0402 thick film surface mount resistor with ±1% tolerance, provides
More informationproduct specification
4414 ML Customer specification: No Version: 1.0 Created: 16.09.2011 INDEX 1 General... 2 2 Mechanics... 2 2.1 GENERAL... 2 2.2 MOTOR... 2 2.3 CONNECTIONS... 3 3 Operating Data... 4 3.1 OPERATING DATA -
More informationModification Record of Product Specification
Modification Record of Product Specification No, DSP-14 1303 Product Name SRV Connector Systems Rev. No, Note Reason Place Date Engineer R0 Initial Release DEC 2.19.14 A.M. Page 1/17 PRODUCT SPECIFICATION
More informationCRS-A Series High Power Anti-Surge Resistor
*RoHS COMPLIANT, **HALOGEN FREE & AEC-Q200 COMPLIANT Features Thick film technology Power rating up to 2 watts at 70 C High power surge withstanding Sulfur-resistant design (ASTM B-809) RoHS compliant*
More informationFrelTec GmbH. Multilayer Ceramic Chip Inductors SMD
GmbH Mathildenstr. 10A 82319 Starnberg Germany Multilayer Ceramic Chip Inductors SMD 10/12/2010 1/12 Freltec GmbH www.freltec.com SPECIFICATION Part Number 090 02 * 101 * J * T04 Type Size Value Tolerance
More informationHigh Performance, Microminiature Circular Connectors
High Performance, Microminiature Circular Connectors HR25 Series Mated dimensions 3. 35. Diagrams of Connectors in Combination Solder type plug (HR25-*TP-**) Crimp type plug (HR25-9TP-**C) Solder type
More informationCDMA RF SAW Filters SF14 Series
CDMA RF SAW Filters Features Small size Low insertion loss High selectivity Hermetic seal Applications CDMA How to Order SF 14 881 M 5 UB B1 1 2 3 4 5 6 7 1 Type of Product (SAW Filter) 2 Package Size
More informationRA / Internal Gear Pump Model GP2, Series 2X Fixed Displacement. Typical application:
Sizes 6.3 to 16 Internal Gear Pump Model GP2, Series 2X Fixed Displacement up to 576 PSI.397 to.98 in 3 (35 bar) (6.5 to 16 cm 3 ) RA 1 23/6.97 RA 1 23/6.97 Characteristics: Peak pressure of up to 576
More informationSELECTION GUIDE. Order code B0303NXT-1W B0305NXT-1W B0309NXT-1W
B-NXT-1W 1W, FIXED INPUT, ISOLATED SINGLE OUTPUT SMD DC-DC CONVERTER FEATURES Footprint over pins 1.37cm 2 Short Circuit Protection(automatic recovery) I/O isolation voltage 1000VDC Operating Temperature:
More informationPlatinum-chip Temperature Sensors in SMD Design Type According to DIN EN 60751
Data Sheet 906125 Page 1/5 Platinum-chip Temperature Sensors in SMD Design Type According to DIN EN 60751 Design type PCS/PCF For temperatures from -50 to +150 C (-70 to +250 C) In accordance with DIN
More informationConductive Polymer Aluminum Capacitors SMD (Chip), Low Impedance
Conductive Polymer Aluminum Capacitors SMD (Chip), Low Impedance FEATURES Useful life: up to 2000 h at 105 C Very low ESR and high ripple current High voltages up to 100 V AEC-Q200 qualified products on
More informationFP1008R5 and FP1008R6 High frequency, high current power inductors
Technical Data 152 Effective April 217 FP18R5 and FP18R6 High frequency, high current power inductors Applications Multi-phase and Vcore regulators Voltage Regulator Modules (VRMs) and high power density
More informationTransient Voltage Suppression Diodes SMTO ka > LTKAK6 series. Description. Features. Test Current I T. Reverse Breakdown Voltage (V BR I T
SMTO-218-6 ka > LTKAK6 series LTKAK6 Series RoHS Pb e3 Description The LTKAK6 series offers superior clamping characteristics over standard S.A.D. technologies by virtue of the Littelfuse Foldbak technology,
More informationPOLY-FUSE Resettable PTCs Surface Mount > 1206L Series
Description The PTC provides surface mount overcurrent protection for applications where space is at a premium and resettable protection is desired. Features Agency Approvals AGENCY AGENCY FILE NUMBER
More informationSFI Electronics Technology
1. Part Number Identification SFI 2220 SA 240 250 J Company Logo Inner Code Size 1206~3220 SA SHA Series 250 250 = 25 10 0 V=25J 1R5 1R5 = 1.5J Breakdown Voltage 240 = 24 10 0 V=24V 151 = 15 10 1 V=150V
More informationMetal Oxide Varistor:TVM-B Series
Features 1. RoHS compliant 2. High surge suppress capability 3. EIA size 0402 ~ 2220 4. Operating voltage: 5.5 ~ 85 Vdc 5. Bidirectional and symmetrical V/I characteristics 6. Multilayer ceramic construction
More informationJapan. ND (Size 2012) (Size 1608) Non winding (RF, 1E) and wire wound type chip inductors for automatic mounting and high-density mounting
Chip Inductors Japan Series: Chip Type: RF, NC, FA, PE, EA RE, ND, NA, FC, FB, SA, PC, PA, RF (Size 5) 1E (Size 1608) ND (Size 2012) 1C (Size 2520) 1A (Size 3225) FB (Size 4532) Non winding (RF, 1E) and
More informationSurface Mount > 1812L Series. Description. Features. Applications. I max (A) typ. (W) P d. Current (A)
1812L Series RoHS Description The 1812L Series PTC provides surface mount overcurrent protection for applications where resettable protection is desired. Features RoHS compliant, lead-free and halogen-free
More informationPRODUCT SPECIFICATION
1.0mm Pitch ZIF FPC Page 1 Top Entry Side Entry 1.0mm Pitch ZIF FPC Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for 1.0mm Pitch ZIF FPC Connector 2.0 APPLICABLE
More informationHigh Performance, Microminiature Circular Connectors
High Performance, Microminiature Circular Connectors HR25 Series Mated dimensions 3. Diagrams of Connectors in Combination Features Solder type plug (HR25-*TP-**) Crimp type plug (HR25-9TP-**C) 1. Small,
More informationSELECTION GUIDE. Order code Voltage(VDC) NTE0303XMC NTE0305XMC
1W, FIXED INPUT, ISOLATED SINGLE OUTPUT SMD DC-DC CONVERTER FEATURES Footprint over pins 1.37cm 2 Short Circuit Protection(automatic recovery) I/O isolation voltage 1000VDC Operating Temperature: -40 ~+85
More informationProduct Data Sheet 4184 NXHH
The engineer's choice 4184 NXHH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationPower Inductor. Shielded. PS Series 2. PCS Series 4. PCDR Series 7. PCDS Series. SCDS Series 12. Packaging Info 14. Environmental Specifications
Power Inductor Shielded PS Series 2 PCS Series 4 PCDR Series 7 PCDS Series 10 SCDS Series 12 Packaging Info 14 Environmental Specifications 16 Tel: 1-888-734-7347 Fax: 919-850-9504 E-mail marketing@seielect.com
More information