SPECIFICATION 三洋精密株式会社. Page 1/10. Version: 0.1 Model name: NRS-3388(i) Date:

Transcription

1 Page 1/10 Date Originator Version Detail spec changes T. Takagi 0.1 Preliminary spec written SANYO SEIMITSU CO., LTD. 1771,NAKAMARUKO UEDA-SHI NAGANO-KEN JAPAN Approval Exam Check Design

2 Page 2/10 This specification is only applicable to NRS-3388(i) 1. Environmental characteristics 1-1 Operating temperature ranges -30 C ~ +70 C 1-2 Storage temperature ranges -40 C ~ +85 C 2. Mechanical characteristic A detailed mechanical drawing for the vibration motors shall be provided with dimensions and tolerances. 2-1 Pull out strength of counter weight and shaft 30 N Min 2-2 Axial play of shaft 0.3 mm Max 2-3 Counter weight density 17g/cc Min 2-4 Total weight Approximately 1.3g 2-5 Rotating direction CW/CCW 2-6 Mechanical noise of motor operating at rated speed 45 db Max A-weighting (Measured distance 10 cm, see Appendix 1.) 2-7 Functional dimensions M013388**, Appendix Bracket material SPCE 2-9 Terminal material C7521R-H 2-10 Bracket and Terminal undercoating Ni plating 2-11 Bracket and Terminal surface finish 2~5 microns, Sn plating 3. Electrical characteristics Principle measurement: 5 C ~35 C; relative humidity 30%~90%. For abnormalities: 20 C +/- 2 C, 65% +/- 5%. Measurements with test jig 3-1 Voltage rating, nominal operating 1.3 V Voltage at specified rotating speed 3-2 Operating voltage (min/max) 1.1 V ~ 1.5 V 3-3 Current rating at nominal voltage 105 ma Max 3-4 Starting current at nominal voltage 130 ma Max 3-5 Starting voltage at rated load 1.1 V Max 3-6 Insulation resistance and voltage breakdown 1 M ohm Min 3-7 Max transient voltage 6.0V 3-8 Terminal resistance /- 2 ohm (2/3 poles) 3-9 Operating speed at rated voltage 9,500 + /- 2,000 rpm 4. Reliability and Environmental testing

3 Page 3/10 5. Marking of the parts Following markings must be placed in parts whenever possible in order listed: 1. Version marking 2. Manufacturing date code 3. Part number. Marking of the part number must be agreed separately and it must be defined in supplier specification or in supplier drawing. Lot No. Indication Lot No. is indicated by print as below :

4 Page 4/10 Day Day print A B C D E F G day print H I J K L M N O P Q R S T U V Month Month print X Y Z Year Year print Factory & Production Line ID Characteristics = 26 Alphabets (ABC Z) 9 Numbers (123 9) 30 Symbols (#$&%+-/? ) Number of pattern ( ) x 2 = 130 pattern Version information A1, A2, COLOR Factory 1 HSM => BLACK Factory 2 SHJ => GREEN Factory 3 SPB => BLUE

5 Page 5/10 Packing Condition 6-1 Smallest packing reel packing dimension

6 Page 6/ Final packing Bubble sheet (Top) Corner Pad protector x 4 a. 700pcs / 1 reel x 6 reel =4,200pcs Upper side: Counter Weight Bubble sheet (Bottom) (350) (250) Double wall corrugated cardboard (350)

7 Page 7/10 7. Format of the Bar Code Label 8. Warranty 9. Handling 9-1 Low molecule silicon compound, which is included in silicon products, may cause electrical failure. Verify sufficiently when you use silicon products. 9-2 Verify sufficiently that adhesives or seals do not outgas corrosive gases that harm the motor. Cyano adhesive or sulfur gases will cause the motor failure. Also, if an adhesive is used to install the motor, ensure the adhesive does not flow into motor (especially bearing part.) 9-3 Ambient temperature and humidity during motor operation affect performance and product life. Do not store motor in locations subject to high temperatures and high humidity or in corrosive gas environment. Below are recommended storage conditions. Temperature: -5 C ~ +40 C, humidity: 15% ~ 70%. 10. Critical characteristics 11. Integration guideline 11-1 Do not subject the motor under locked condition over 10 seconds Do not exert pressure by pushing the current terminals towards the direction of the internal motor Recommended Pad layout of PWB is included in drawing. (See appendix 2) 11-4 The gap (clearance) from other component should be 0.5mm Min. (Especially for Counterweight) 11-5 Possible to hold by softer material on motor case and Bracket. 12. Expected shipping and storage condition 12-1 Relative humidity 15 % 70 % 12-2 Temperature -5 C 40 C 12-3 Sulphur dioxide average 0.3 mg/m Sulphuretted hydrogen average 0.1 mg/m Maximum storage period 12 months 13. Quality

8 Page 8/ Others 14-1 Out-going test data will be attached (n-35) for Loaded rotation Loaded current Lock current (Starting current) Starting voltage 14-2 Recommended Reflow profile Reflow specification 245 Peak temperature: Rate of temperatuer rise: 1~4 /sec Rate of temperatuer rise: 2~4 /sec 120 Pre-heat time: 70±20sec Above 220 holding time: 30±10sec

9 Page 9/10 Appendix 1 ELASTIC BAND VIBRA MICROPHONE 100mm JIG Figure mm 100mm Figure 2. Figure 3.

10 Page 10/10 Appendix 2