NEW AMERICAN AIRLINES

Transcription

1 Revision / NEW AMERICAN AIRLINES Ground Equipment Paint Manual (GEPM)

2 This Manual illustrates the locations for markings, Decals or placards for consistent placement. GEPM Page 1

3 TABLE OF CONTENTS 1. EQUIPMENT REFINISHING PAINT. Revisions index pg. 4 A. General pg. 5 B. Approved Materials pg. 5 C. Color pg. 5, 6 D. Exterior pg. 6 E. Interior pg. 7 F. Other pg. 7 G. Identification Markings pg EQUIPMENT SPECIFIC MARKINGS 2.0 CONTAINER LOADER-TYPICAL pg. 8, BAGGAGE/CARGO CART/MAIL CART TYPICAL: pg. 10, DOLLIES TYPICAL: pg BOWSER TYPICAL: pg TRAILER MOUNTED EQUIPMENT, TYPICAL (HEATER, AIR CONDITIONER, AIRSTART, GENERATOR)-TYPICAL pg AIR CONDITIONER TYPICAL TLD-802 pg TRAILER MOUNT GPU TYPICAL pg TRUCK MOUNTED AIRSTART / AIR CONDITIONER / GPU- TYPICAL: pg BELT LOADER, CARGO CONVEYER, TYPICAL: pg BELT LOADER (WOLARD) TYPICAL: pg FOUR WHEEL ELECTRIC CART TYPICAL: pg FOUR WHEEL ELECTRIC CART COLUMBIA pg FOUR WHEEL HANDICAPPED PASENGER CART-TYPICAL: pg FOUR WHEEL BURDEN GASOLINE CART TYPICAL: pg THREE WHEEL STOCK CART-TYPICAL: pg ALL-TERRAIN VEHICLE TYPICAL: pg TRACTOR TYPICAL: pg DEICER, JOHN BEAN/LA-1000 pg. 27, DEICER GLOBAL 2200 pg. 29, N DEICER, TYPICAL; FMC D40D, D240, DD1000, DD1200, 2000II, LMD2000, TEMPEST 2, GS5, SIMON 2100, GLOBAL 2100 TE, PREMIER, VESTERGAARD MY. pg. 31, VESTERGAARD BETA S pg. 33, FORKLIFT- TYPICAL: pg PASSENGER STAIRS, WIDE BODY, INDUSTRIAL CHASSIS, TYPICAL: pg PASSENGER STAIR, TRUCK MOUNTED, TYPICAL: pg PASSENGER STAIR, NARROW BODY AIRCRAFT, TYPICAL: pg TOWBAR-TYPICAL: pg. 39, 40 GEPM Page 2

4 TABLE OF CONTENTS CONT: 2.26 BAGGAGE TRACTORS, ELECTRIC TYPICAL: pg BAGGAGE TRACTOR, INTERNAL COMBUSTION DRIVEN, TYPICAL: pg. 42, BAGGAGE TRACTORS NO CAB TYPICAL: pg CARGO HIGH SPEED TRACTOR, TYPICAL: pg AIRCRAFT PUSHOUT TUG GT35 pg AIRCRAFT PUSH OUT TRACTOR, HOUGH pg AIRCRAFT PUSH OUT TRACTOR TYPICAL: pg. 48, PUSH TRACTOR TUG pg AIRCRAFT PUSH OUT TRACTOR (TOWBARLESS)-TYPICAL pg. 51, HIGH-SPEED-TOWBARLESS-TYPICAL pg HIGH LIFT TRUCK TYPICAL: pg. 54, LAVATORY SERVICE TRUCK- NON-VACUUM-TYPICAL pg. 56, LAVATORY SERVICE TRUCK- Vacuum (Vestergaard VTS) pg. 58, POTABLE WATER SERVICE TRUCK TYPICAL: pg BOBTAIL-TYPICAL: pg PANEL/STEP VAN TYPICAL: pg PICK-UP TRUCK TYPICAL: pg WRECKER / SERVICE TRUCK TYPICAL: pg BOX VAN TRUCK TYPICAL: pg STAKE BED TRUCK TYPICAL: pg BOOM LIFT TYPICAL: pg TRUCK MOUNTED MAINTENANCE BOOM LIFT TYPICAL: pg MAINTENANCE ENTRY STANDS TYPICAL: pg MAINTENANCE PLATFORM LIFTS TYPICAL: pg MAINTENANCE / WHEEL CHAIR PLATFORM LIFT ELECTRIC CHARLATTE pg MAINTENANCE LIFTS ELECTRIC TYPICAL: pg SUV TYPICAL: pg UTILITY VEHICLE, MAINTENANCE TYPICAL: pg UTILITY CART TYPICAL: pg UTILITY VAN TYPICAL: pg SPRINTER VAN TYPICAL: pg MINI BUS TYPICAL: LEFT SIDE pg MINI BUS TYPICAL: RIGHT SIDE pg OTHER DECALS 3.0 DECALS COMPANY LOGO s pg. 80, 81, LETTERS AND NUMBERS WHITE pg LETTERS AND NUMBERS BLUE pg LETTERS 2.5 USED WITH TARE WT. DECAL pg DECAL PICTURE INDEX pg GEPM Page 3

5 Revisions Index: 9/7/2015 page 11,12 added wording if Applicable 9/14/2015 page 13 added new photo 10/5/2015 page 66 changed paint color from blue to black on bed 10/6/2015 page 71 added new equipment type ( Wheel Chair Lift) 10/6/2015 page 77 added new equipment type (Sprinter Van ) 10/6/2015 page 69 added new equipment (Maintenance Entry Stands) 02/08/2016 page added language for bag carts and dollies 02/08/2016 page added new color code for international orange GEPM Page 4

6 1. EQUIPMENT REFINISHING PAINT A. General: B. Approved Materials 1. Paint on ground equipment shall be maintained to present an acceptable appearance. (Maintained to AA Standards) 2. Paints and coatings applied by GSE maintenance shall comply with national or local EPA requirements limiting the amount of Volatile Organic Compounds (VOCs) in the paint. Many states have adopted more stringent standards than the federal EPA requirements and you are responsible to understand and comply with all local, state and federal regulations before you paint. Consult with your Supervisor if you have any questions. 3. Paint for GSE maintenance is specified below to maintain uniform color standards. Most paint must be purchased locally due to shipping restriction. C. Color 1. It is the responsibility of the painter to comply with the complete recommended application for the chosen system, including surface preparation, priming and top coats. 2. Application a. Paint can be applied by several methods, although any given method could be restricted, the appropriate method of application will be dictated by your locations regulations. Please consult with your Supervisor for most appropriate method. i. Spray cans (rattle cans) ii. Rollers/brushes iii. Localized spraying and/or Spray Booths 1. The chassis is Blue - match either of these brands in alkyd enamel,acrylic or polyurethane for Skydrol resistance if usage is allowed in your location a. DEVOE color DC4752 Cobalt Blue / Base Stock Dev-lac-1431 Alkyd Enamel b. DEVOE Primer Gray Dev-Prime-1403 Alkyd Enamel c. DEVOE color DC4752 Cobalt Blue / Base Stock Dev-Cryl 1449 Water Based Acrylic d. DEVOE Water based Gray Primer Dev-Cryl 1440 e. Sherwin Williams K B, New American Blue (Urethane) 2. The wheel rims are Gray - match either of these brands in alkyd enamel, acrylic or polyurethane for Skydrol resistance if usage is allowed in your location a. DEVOE color DC6110 Machine Gray / Base Stock Dev-Lac 1431 Alkyd Enamel b. DEVOE color DC6110 Grey / Base Stock Dev-Cryl 1449 Water Based Acrylic c. Sherwin Williams 5A A, American Gray GEPM Page 5

7 3. Comercial cab and chassis, vans and pickups. White a. Base color is Ford Z1 White, most automotive paint stores can cross this number to the brand of paint they sell. 4. Other colors: Use these Sherwin Williams paint codes as a guideline for additional colors that may be required GSE Equipment. a. Sherwin Williams GC741698: Gray b. Sherwin Williams GCCM5970: Yellow c. Sherwin Williams GC52588: Red d. Sherwin Williams GC1738A: Black e. Sherwin Williams GC44093A: White f. Sherwin Williams GC48984A: Blue g. Sherwin Williams GC A: Safety Green h. Dupont 43542: International Orange 5. Contact the GSE Fleet Manager for any questions regarding paints or colors. D. Exterior 1. Equipment outriggers, stabilizers, side hitches, perimeter bars, foldable or stowable handrails, and wheel chocks shall be painted yellow (Note do not paint rubber chocks) 2. Fluid filler caps and a 6" x 6" area around the neck shall be painted according to the fluid type. Fluid type shall be stenciled (or affix decal) on surface adjacent to filler in one inch letters. a. Fluid Filler Caps FLUID CAP COLOR PLACARD, STENCIL or DECAL PLACARD CPN Gasoline Red Red w/ White Lettering / Jet A White w/ Black Stripe White w/ Black Lettering Diesel Green White w/ Green Lettering / Low Sulfur Diesel Green w/ White Stripe Green w/ White Lettering Ultra Low Sulfur Diesel Green w/ White Stripes Green w/ White Lettering Oil & Lubricant Yellow Yellow w/ Black Lettering Hydraulic Oil Yellow w/ Blue Stripe Yellow w/ Blue Lettering / Coolant White White w/ Black Lettering Deicing Fluid Red w/ Yellow Stripe Red w/ White Lettering Anti-Icing Fluid Green w/ Yellow Stripe Green w/ White Lettering Potable Water AA Blue & White Stripe White w/ Blue Lettering Degerm/Water AA Blue Blue w/ White Lettering Non-Potable Water Black White w/ Black Lettering DEF Fluid Blue Blue w/ White Lettering Sage# DEFTCP 3. Maintenance work stands, powered access units, fluid dispensers, fuel trucks, and lavatory service trucks will be finished with polyurethane for maximum fluid resistance. GEPM Page 6

8 E. Other Interior 1. All floor surfaces, walkways and pedals, interior and exterior, shall be covered with Non-slip material unless otherwise specified. Use black conformable safety walk material, CPN or Grip Deck paint, CPN or equivalent as applicable. 1. Maintenance work stands shall be painted American Airlines blue (Aircraft Maintenance) or yellow (Ground Operations). Unless otherwise specified at time of purchase, corporate emblem decals, company numbers and other markings will be installed or applied by AA. See "Identification Markings", following. F. Identification Markings 1. POWERED EQUIPMENT will be identified with the AA "Company Number" as indicated per equipment type. The numbers shall be applied by affixing a decal or a stencil in white characters. If the location is light colored, the numbers should be blue. 2. The AA COMPANY NUMBERS shall be a minimum of four inches high, maximum eight inches high and of proportional width. Font is Arial Bold Company numbers are assigned when the units are purchased and remain with the unit until it is sold or scrapped, regardless of station location or transfer history. Location of the numbers may vary from the guidelines above due to its configuration. Stations are responsible to mark similar units in a consistent manner to maintain uniformity of appearance. 3. For NON-POWERED equipment that requires an EQUIPMENT INVENTORY CODE,( e.g. Towbars, use one-inch characters near the local control number. 4. TIRE INFLATION PRESSURE, (e.g. 30 psi), should be in ½ high white characters on the fender above each wheel. 5. RED/WHITE SAFETY REFLECTOR 2 x12 CPN ( ) shall be installed on mobile ground equipment as illustrated in the trim drawings in this Section. In general, the reflectors shall be installed on the corners of the equipment as high and as far outboard as possible. Station should mark similar units in a consistent manner to maintain uniformity of appearance. 6. For vehicles needing the replacement of Class "A" plastic or glass reflectors, use RED SAFETY REFLECTORS, three inch, CPN / , and AMBER SAFETY REFLECTORS, three inch, CPN / Red reflectors shall be positioned at the rear, amber reflectors shall be positioned at the front. This does not apply to any licensed vehicle. 7. LOGO DECALS, SAFETY REFLECTORS and INSTRUCTIONS shall be located as shown on the trim illustrations in this Section. 8. All AA and OEM control, instruction and identification stencils and decals must be checked on as specified on the PM inspections and shall be reapplied as necessary to maintain legibility. GEPM Page 7

9 2. EQUIPMENT SPECIFIC MARKINGS 2.0 CONTAINER LOADER, TYPICAL: I. Loader Chassis: New American Blue. II. Stabilizers, Ladders, Handrails, Movable Container Guides, & Container Stops: Yellow. III. Wheel Hubs: AA Gray. IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) White Reflective. B. Decal or Stencil: Unit Number 4 Tall Both sides of chassis and front. C. Reflectors: Red/White Reflectors 2 x12 on all four corners. CPN ( ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations. (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering. (pneumatic tires only)(cpn ) GEPM Page 8

10 GEPM Page 9

11 2.1 BAGGAGE/CARGO CART/MAIL CART/, TYPICAL: I. Exterior body of cart: New American Blue. II. Interior: White / Open carts (No Top) All Blue. III. Tongue and Hitches: Yellow. IV. Wheels: AA Gray. V. All Letters & Numbers: White on Blue. VI. Bumpers: Top Corners Black. GEPM Page 10

12 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo Flat cart (CPN / )Full-size cart (CPN / ) White Reflective. (Center decal both ends between ribs) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: 2 x 12 strips of 2 DOT-C2 red/white reflective tape top & bottom.(50% min coverage) (CPN ) D. Reflective tape: 2 x 12 DOT-C2 white reflective strips. (CPN ) E. Reflective tape: 1 DOT-C2 red/white reflective tape, 1 x 12 strips. (50% min coverage) (CPN ) F. Decal or Stencil: Tare Weight Decal 2.5 (if applicable) both ends of cart/dolly. (only use actual cart/dolly weight when applicable) (CPN ) G. Decal: Black Chalkboard Material. (CPN / ) H. Corner Bumpers black all four upper corners of unit covered carts only. (CPN I. Decal Year color coded: Place in upper right-hand corner on each end of cart ( available soon) GEPM Page 11

13 2.2 DOLLIES TYPICAL: I. Exterior body of cart: New American Blue. II. Tongue and Hitches: Yellow. III. Container Locks, Lock Handles and Guide Rails: Yellow. IV. Wheels: AA Gray. V. All Letters & Numbers: White on Blue. 1. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 2. AA Decals and Markings: A. Decal: AA logo (CPN / ) White Reflective. B. Reflectors : 2 x 12 strips of 2 DOT-C2 red/white reflective tape top & bottom.(50% min coverage) (CPN ) C. Reflective tape : 1 DOT-C2 red/white reflective tape, 1 x 12 strips. (50% min coverage) (CPN )) D. Decal or Stencil E. Decal or Stencil: Unit Number 4 Tall. (Some Dollies might have space constraint requiring 2.5 lettering) GEPM Page 12

14 2.3 BOWSER- TYPICAL: I. Exterior: New American Blue. II. Tongue: Yellow. III. Wheels: AA Gray. IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) White Reflective Both sides centered. B. Decal or Stencil: Unit Number 4 Tall Both ends upper section. C. Reflectors: Red/White 2 x12 on all four corners. (CPN ) D. Decal or Stencil: Contents in Tank i.e., Used Oil, Diesel Fuel etc. Both Sides. E. Reflective tape : 1 DOT-C2 red/white reflective tape, 1 x 12 strips (50% min coverage)both Sides. (CPN ) GEPM Page 13

15 2.4 TRAILER MOUNTED EQUIPMENT, TYPICAL (HEATER AIR CONDITIONER, AIRSTART) I. Exterior: New American Blue. II. Tongue: Yellow. III. Wheels: AA Gray. IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) (centered on side panel) White Reflective. B. Decal or Stencil: Unit Number 4 Tall. (upper rear sides) C. Reflectors: Red/ White Reflectors 2 x12 on all four corners UPPER AND LOWER. (CPN ) D. Decal or Stencil: Tire Pressure #, ½ Lettering. (pneumatic tires only)(cpn ) E. Reflective tape : 1 DOT-C2 red/white reflective tape, make. (50% min coverage) (CPN ) F. Decals: For Airstarts only. (CPN / ) G. Corner Bumpers black all four upper corners of unit. (CPN ) GEPM Page 14

16 2.5 TRAILER MOUNTED EQUIPMENT, TYPICAL (HEATER AIR CONDITIONER, 802 TLD I. Exterior: New American Blue. II. Tongue: Yellow. III. Body Panels: Galvanized or Stainless. (Do Not Paint) IV. Wheels: AA Gray. V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue. 4. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 5. AA Decals and Markings: A. Decal: AA Logo ( / ) (centered on both side panels) White Reflective. B. Decal or Stencil: Unit Number 4 Tall (both sides towards rear of unit) C. Reflectors: Red / White Reflectors 2 x12 wrap around all four corners. (CPN ) D. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) Above Tires on Fenders. E. Reflective tape: 1 DOT-C2 red/white reflective tape, make. (50% min coverage) (CPN ) GEPM Page 15

17 2.6 TRAILER MOUNTED EQUIPMENT, TYPICAL GPU I. Exterior: New American Blue. II. Tongue: Yellow. III. Body Panels: Galvanized or Stainless. (Do Not Paint) IV. Wheels: AA Gray. V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue. 6. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 7. AA Decals and Markings: A. Decal: AA Logo ( / ) (centered on both side panels) White Reflective. B. Decal or Stencil: Unit Number 4 Tall (both sides towards rear of unit) C. Reflectors: Red / White Reflectors 2 x12 wrap around all four corners. (CPN ) D. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) Above Tires on Fenders. E. Reflective tape: 1 DOT-C2 red/white reflective tape, make. (50% min coverage) (CPN ) GEPM Page 16

18 2.7 TRUCK MOUNTED AIRSTART / AIR CONDITIONER / GPU -TYPICAL : I. Exterior: Cab AA White Rear Section New American Blue. II. Body Panels: Galvanized or Stainless. (Do Not Paint) III. Wheels: AA Gray. IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue, Blue on White. 1. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 2. AA Decals and Markings: A. Decal: AA Logo CPN ( / ) Color Reflective. (Centered on both doors) / CPN / White reflective. (centered on rear panels both sides) B. Decal or Stencil: Unit Number 4 Tall. (Upper rear both Sides and on Front of hood) C. Reflectors: Red / White Reflectors 2 x12 on all four corners top and bottom rear. (CPN ) D. Decal: 3 in 1 Safety Decal (SAGE PART: / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle. (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft. (CPN / ) iii. Decal: Set Parking Brake When Not in Use. (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations. (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering. (pneumatic tires only)(cpn ) G. Decal: Seat Belt must Worn. (CPN ) H. Decal: ALERT Jet-Start Mode. (CPN ) for Air start model I. Decal: CAUTION Warm up Rear Engine (CPN ) for Air start model GEPM Page 17

19 2.8 BELT LOADER,TUG 660 CARGO CONVEYER, TYPICAL I. Chassis: New American Blue. II. Wheels: AA Gray. III. Interior: Apply Non-skid to floors and pedals as needed. IV. Handrails: Yellow. V. Boom Safety Bar: Yellow. ( if applicable) VI. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VII. All Letters & Numbers: White on Blue. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Both Sides) White Reflective. B. Decal or Stencil: Unit Number 4 Tall. (Both Sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners. (CPN ) D. Decal: 3 in 1 Safety Decal. (SAGE PART: / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations. (CPN / ) F. Decal: Seat Belt must be worn. (CPN ) G. Decal or Stencil: Pinch Point in two places. (2 high characters on each side of boom) (CPN ) H. Placard: NO SAFETY PROP : TUG 660 only. (CPN / ) I. Decal or Stencil: Tire Pressure #, ½ Lettering. (pneumatic tires only)(cpn ) J. Decal or Stencil: Caution: High Voltage located at the connector Electric Units Only. (CPN ) K. Decal: No Smoking (CPN / ) at vicinity of battery lid area. ( both sides if applicable) Electric Units Only GEPM Page 18

20 2.9 BELT LOADER, CARGO CONVEYER, TYPICAL I. Chassis: New American Blue. II. Wheels: AA Gray. III. Interior: Apply Non-skid to floors and pedals as needed. IV. Handrails: Yellow. V. Boom Safety Bar: Yellow. VI. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VII. All Letters & Numbers: White on Blue. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Both sides) White Reflective. B. Decal or Stencil: Unit Number 4 Tall. (Both Sides of conveyor) C. Reflectors: Red/White Reflectors 2 x12 on all four corners. (CPN ) D. Decal: 3 in 1 Safety Decal. (SAGE PART: / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse of This Vehicle Is In Violation of AA Regulations. (CPN / ) F. Decal: Seat Belt must be Worn (CPN ) G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) H. Decal: CAUTION do not raise rear bed when using safety prop (CPN ) Place on drivers side of safety prop I. Decal: Caution use safety prop when working under conveyor (CPN TY10 / ) Place on safety prop in plain view GEPM Page 19

21 2.10 FOUR WHEEL ELECTRIC CART-TYPICAL I. Exterior body of cart: Factory Color until repaint is required then paint New American Blue II. Hitches: Yellow III. Interior: Apply Non-skid to floors and pedals as needed. IV. Wheels: AA Gray V. All Letters & Numbers: White on Blue 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) White Reflective Centered on front B. Decal or Stencil: Unit Number 4 Tall (Centered on both sides) C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) Wrap corner Red on side white section towards front. D. Decal: Seat Belt must be worn (CPN ) E. Decal: 3 in 1 Safety Decal (SAGE / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 20

22 2.11 FOUR WHEEL ELECTRIC CART-COLUMBIA TYPICAL I. Exterior body of cart: Factory Color until repaint is required then paint New American Blue II. Hitches: Yellow III. Interior: Apply Non-skid to floors and pedals as needed. IV. Wheels: AA Gray V. All Letters & Numbers: White on Blue/ Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) White Reflective Centered on front B. Decal or Stencil: Unit Number 4 Tall (Centered on both sides) C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) Wrap corner Red on side white section towards front. D. Decal: Seat Belt must be worn (CPN ) E. Decal: 3 in 1 Safety Decal (SAGE / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 21

23 2.12 FOUR WHEEL HANDICAPPED PASENGER CART-TYPICAL : I. Exterior body of cart: AA White II. Hand Rails: Black III. Wheels: AA Gray IV. All Letters & Numbers: Blue on White ` 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) Color Reflective (FRONT AND REAR) B. Decal or Stencil: Unit Number 2.5 Tall C. Decal: HANDICAPPED (CPN ) D. Station Information: E. Decal: Seat Belt Must Be Worn (CPN ) GEPM Page 22

24 2.13 FOUR WHEEL BURDEN GASOLINE CART TYPICAL I. Exterior body of cart: Factory Color until repaint is required then paint New American Blue II. Hitches: Yellow III. Wheels: AA Gray IV. Interior: Apply Non-skid to floors and pedals as needed V. All Letters & Numbers: White on Blue 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Centered on Panels) White Reflective B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) D. Decal: Seat Belt must be worn (CPN ) E. Decal: 3 in 1 Safety Decal (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 23

25 2.14 THREE WHEEL STOCK CART-TYPICAL I. Exterior body of cart: Factory Color until repaint is required then paint New American Blue II. Hitches: Yellow III. Interior: Apply Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. All Letters & Numbers: White on Blue 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) White Reflective B. Decal or Stencil: Unit Number 4 Tall (Both Side) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety (CPN / ) GEPM Page 24

26 2.15 ALL-TERRAIN VEHICLE TYPICAL I. Exterior body of cart: New American Blue or original factory color. II. Hitches: Yellow III. Wheels: AA Gray IV. All Letters & Numbers: White on Blue 2. Required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA. Logo (CPN / ) White Reflective B. Decal or Stencil: Unit Number 4 Tall (Front and Rear) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: Seat Belt must be worn (CPN ) E. Decal: 3 in 1 Safety Decal (CPN / ) GEPM Page 25

27 2.16 TRACTOR -TYPICAL I. Exterior body of Tractor: Factory Color until repaint is required then paint New American Blue. II. Hitches: Yellow III. Wheels: AA Gray IV. All Letters & Numbers: White on Blue V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) 2. Required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Both sides) White Reflective B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/ White Reflectors 2 x12 Wrap front corners and best fit on rear corners (CPN ) D. Decal: Seat Belt must be worn (CPN ) E. Decal: 3 in 1 Safety Decal (CPN / ) GEPM Page 26

28 2.17 DEICER, JOHN BEAN/LA-1000 I. Chassis: New American Blue II. Boom: New American Blue III. Basket: Yellow IV. Non-plated bumpers : Black V. Wheel Hubs: AA Gray VI. Hitch: Yellow VII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VIII. All Letters & Numbers: White on Blue 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. Required Decals and Markings: A. Reflectors: Red/White Reflector 2 x12 on all four corners (CPN ) B. Decal: DANGER Do not operate this equipment within 10 ft. of high voltage lines C. Decal or Stencil: Step D. Decal: AA Logo (CPN / ) White Reflective E. Decal: WARNING Keep 5 feet clear of Aircraft Engine & Fuel Tank F. Decal: Unit Number 4 Tall G. Decal or Stencil: Lock Door H. Decal: Basket Capacity 500 lb. Max I. Stencil: No Step GEPM Page 27

29 J. Stencil: 197 K. Decal or Stencil: Fill to 3 below top of tank L. Stencil: Suction Valve M. Stencil: Keep Clear in six places along boom rest area N. Tape: Black & Yellow stripe along boom rest 2 wide minim O. Stencil: 665 Gal. Tank P. Stencil: Detergent only if units are used for aircraft washing Q. Stencil: Blower Motor Circuit Breaker Inside (1/2 lettering) R. Decal or Stencil: Tire Pressure #, ½ Lettering (CPN ) S. Decal: DO NOT ELEVATE BOOM /BASKET WHEN WIND GUSTS EXCEED 40 KNOTS (46 MPH) (CPN / ) T. Label: Hazard Warning Label (8 ½ x 11 color bar label, (CPN ) for fluid tank contents; locate decal adjacent to tank sight gage (not shown). Seal edges of decal with Edge Sealer. U. Decal: FULL BODY SAFETY HARNESS MUST BE USED AT ALL TIMES WHEN IN THE DEICING BUCKET, *3-1/2 x 5 yellow background with black copy, (CPN / ) ((GSER GR.11871) (latest revision). V. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: W. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse of This Vehicle Is In Violation of AA Regulations (CPN / ) X. Decal: Seat Belt must be Worn (CPN ) GEPM Page 28

30 2.18 DEICER, TYPICAL; GLOBAL 2200 I. Exterior;, AA White II. Body Panels: Galvanized or Stainless (Do Not Paint) Note: Do not paint corrugated polished aluminum or fiberglass bodies with molded-in color do not need painting III. Boom : AA White IV. Non-plated Bumper: Black V. Wheels: AA Gray VI. Handrails/Ladders: Yellow VII. Basket/Cab: Yellow VIII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IX. All Letters & Numbers: White on Blue, Blue on White X. Special Consideration: Many deicing vehicles are equipped to dispense both de-icing fluid and anti-icing fluid. In order to assure that fluids are loaded properly into the trucks and the fluids are properly dispensed onto the airplanes, all of the following components must be labeled: i. Nozzles, Load points; fittings, hatches, vents ii. Hoses Controls; valves, indicators, switches iii. Gauges; pressure, quantity These components must be labeled as referring to: DEICING FLUID or ANTI-ICING FLUID Reference GSER GR (Latest Revision).Further detail, describing product or use may be required. Consult with the manufacturer or GSE FLEET TEAM. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. Required Decals and Markings: GEPM Page 29

31 A. Decal: AA Logo (CPN / )(Both sides)(cpn / ) (both doors) B. Unit Number: (6-inch high characters) C. NOTE: Some stations require 12-inch high numbers on roof of Deicers. D. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) E. Decals: DO NOT ELEVATE BOOM /BASKET WHEN WIND GUSTS EXCEED 40 KNOTS (46 MPH). (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (CPN ) G. Label: Hazard Warning Label (8 ½ x 11 color bar label, CPN ) for fluid tank contents locate decal adjacent to tank sight gage (not shown). Seal edges of decal with Edge Sealer, or equivalent. H. Decal: FULL BODY SAFETY HARNESS MUST BE USED AT ALL TIMES WHEN IN THE DEICING BUCKET, on exterior basket entry door [3-1/2 X 5 yellow background with black copy, (CPN / ) ((GSER GR (latest revision))]. I. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: J. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) K. Decal: Seat Belt must be Worn (CPN ) GEPM Page 30

32 2.19 N DEICER, TYPICAL; FMC D40D, D240, DD1000, DD1200, 2000II, LMD2000, TEMPEST 2, GS5, SIMON 2100, GLOBAL 2100 TE, PREMIER, VESTERGAARD, MY I. Exterior; AA White unless previously painted Blue II. Body Panels: Galvanized or Stainless (Do Not Paint) Note: Do not paint corrugated polished aluminum or fiberglass bodies with molded-in color do not need painting III. Boom : AA White unless previously painted Blue IV. Non-plated Bumper: Black V. Wheels: AA Gray VI. Handrails/Ladders: Yellow VII. Basket/Cab: Yellow VIII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IX. All Letters & Numbers: White on Blue, Blue on White X. Special Consideration: Many deicing vehicles are equipped to dispense both de-icing fluid and anti-icing fluid. In order to assure that fluids are loaded properly into the trucks and the fluids are properly dispensed onto the airplanes, all of the following components must be labeled: i. Nozzles, Load points; fittings, hatches, vents ii. Hoses Controls; valves, indicators, switches iii. Gauges; pressure, quantity, These components must be labeled as referring to: DEICING FLUID or ANTI-ICING FLUID Reference GSER GR (Latest Revision).Further detail, describing product or use may be required. Consult with the manufacturer or GSE FLEET TEAM. GEPM Page 31

33 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 4. Required Decals and Markings: A. Decal: AA Logo (CPN / )(Both sides)(cpn / ) (both doors) B. Unit Number: (6-inch high characters) C. NOTE: Some stations require 12-inch high numbers on roof of Deicers. D. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) E. Decals: DO NOT ELEVATE BOOM /BASKET WHEN WIND GUSTS EXCEED 40 KNOTS (46 MPH). (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (CPN ) G. Label: Hazard Warning Label (8 ½ x 11 color bar label, CPN ) for fluid tank contents locate decal adjacent to tank sight gage (not shown). Seal edges of decal with Edge Sealer, or equivalent. H. Decal: FULL BODY SAFETY HARNESS MUST BE USED AT ALL TIMES WHEN IN THE DEICING BUCKET, on exterior basket entry door [3-1/2 X 5 yellow background with black copy, (CPN / ) ((GSER GR (latest revision))]. I. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: J. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) K. Decal: Seat Belt must be Worn (CPN ) GEPM Page 32

34 2.20 VESTERGAARD BETA S I. Exterior: AA White II. Basket / Cab Yellow III. Body Panels: Galvanized or Stainless (Do Not Paint) Note: Do not paint Corrugated polished aluminum or fiberglass body with molded-in color need not be painted IV. Non-plated Bumpers: Black V. Wheels: AA Gray VI. Handrails: Yellow VII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VIII. All Letters & Numbers: Blue on White/ White on Blue IX. Special Consideration: Many deicing vehicles are equipped to dispense both de-icing fluid and anti-icing fluid. In order to assure that fluids are loaded properly into the trucks and the fluids are properly dispensed onto the airplanes, all of the following components must be labeled: i. Nozzles, Load points; fittings, hatches, vents ii. Hoses Controls; valves, indicators, switches iii. Gauges; pressure, quantity These components must be labeled as referring to: DEICING FLUID or ANTI-ICING FLUID Reference GSER GR (Latest Revision).Further detail, describing product or use may be required. Consult with the manufacturer or GSE-HDQ. GEPM Page 33

35 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. Required Decals and Markings: A. Decal: AA Logo (CPN / ) (Both sides) B. Unit Number: (6-inch high characters) NOTE: Some stations require 12-inch high numbers on roof of Deicers. C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) D. Optional Airport specific identification # s E. Decals: DO NOT ELEVATE BOOM /BASKET WHEN WIND GUSTS EXCEED 40 KNOTS (46 MPH). (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (CPN ) G. Decal: Reflective Red & Blue Strips obtain from mfg. H. Hazard Warning Label (8 ½ x 11 color bar label, CPN ) for fluid tank contents locate decal adjacent to tank sight gage (not shown). Seal edges of decal with Edge Sealer, or equivalent. I. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii Decal: Set Parking Brake When Not in Use (CPN / ) J. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) K. Decal: Seat Belt must be Worn (CPN GEPM Page 34

36 2.21 FORKLIFT- TYPICAL : I. Chassis: Factory Color unless previously painted then paint New American Blue II. Wheels: AA Gray III. Interior: Apply Non-skid to floors and pedals as needed IV. Forks: Yellow V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White or Blue Depending on main color 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) Color Reflective( Note: if Blue use CPN / White reflective) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 35

37 2.22 PASSENGER STAIRS, WIDE BODY, INDUSTRIAL CHASSIS, TYPICAL I. Chassis: White II. Stair Side Panels, Inside & Outside, Step Risers: White III. Handrails (steel): White IV. Handrails (aluminum): Unpainted V. Step Treads: Unpainted ( Note: unless previously coated with anti-skid) VI. Stabilizers: Yellow VII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VIII. All Letters & Numbers: Blue on White IX. Wheels: AA Gray 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / )Place on Upper Side Panels Both Sides / Logo for front of unit (CPN / )Center on Front B. Decal or Stencil: Unit Number 4 Tall Place on upper Panel Lower Rear of Logo C. Reflectors: Red/White Reflectors 2 x12 (CPN ) Place on all Four Corners D. Decal: 3 in 1 Safety Decal (CPN / ) Place on Dash E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) Place on Dash F. Decal or Stencil: Tire Pressure #, ½ Lettering (CPN )Place Above Tires on Fender G. Decal: Warning: Do Not Elevate This Platform When Wind Gusts Exceed 35 Knots (40 MPH). (CPN / )Place in Drivers Compartment Visible to Operator H. Decal: Seat Belt must be Worn (CPN ) Place on Dash GEPM Page 36

38 2.23 PASSENGER STAIR, TRUCK MOUNTED, TYPICAL I. Cab: White II. Stair Side Panels, Inside & Outside, Step Risers: AA White III. Handrails (steel): White IV. Handrails (aluminum): Unpainted V. Chassis: White VI. Step Treads: Unpainted ( Note: unless previously coated with Non-skid) VII. Stabilizers: Yellow VIII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IX. All Letters and Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins 3. AA Decals and Markings: A. Decal: AA Logo for upper side panels (CPN / ) (Both on Both Doors) (CPN / ) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Warning: Do Not Elevate This Platform When Wind Gusts Exceed (40 MPH) (CPN / ) H. Decal: Seat Belt must be Worn (CPN ) GEPM Page 37

39 2.24 PASSENGER STAIR, NARROW BODY AIRCRAFT, TYPICAL I. Stair Side Panels, Inside & Outside: White II. Step Risers: White III. Handrails (steel): White IV. Handrails (aluminum): Unpainted V. Chassis: New American Blue VI. Step Treads: Unpainted ( Note: unless previously coated with Non-skid) VII. Stabilizers: Yellow VIII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IX. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Both sides) Color Reflective B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Warning: Do Not Elevate This Platform When Wind Gusts Exceed 35 Knots (40 MPH). (CPN / ) G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 38

40 2.25 TOWBAR-TYPICAL I. Paint: Towbars are to be painted with Skydrol resistant paint if it use is allowed at your location a. Towbar tube and landing gear b. Do not paint heads unless specified by OEM c. Numbers and Letters Blue on Yellow II. Colors: a. S80: Red b. 737/A319/A320/A321: Yellow c. 757/A330/767/777/787: Yellow d. CRJ/ ERJ: Yellow 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) Both sides head end of bar. B. Decal or Stencil: Unit Number 4 Tall Both sides eyelet end of bar. C. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) D. Decal: WARNING Ensure wheels are down before disconnecting (CPN ) E. Stencil: Aircraft type (s) 2 Tall (all aircraft types applicable are required to at least be listed once on the bar) Aircraft type shall show in the following configuration to match Nose Landing Gear Door Identifiers: Aircraft Type Towbar Markings i. S80 MD80 ii iii. A319 A319 iv. A320 A320 v. A321 A321 vi vii. A330 A330 viii ix x xi GEPM Page 39

41 xii xiii xiv. A xv. ERJ-700 ERJ-7 xvi. ERJ-900 ERJ-9 xvii. CRJ-900 CRJ-9 All allowable aircraft types must be stenciled on the bar. Types should be stencil (painted) for improved durability if possible. F. Decal: By-Pass Pin Installed? (CPN ). Install on top of bar G. Reflective tape: 1 x12, (CPN ), apply as follows: i. On MD-80 towbars, place a 2"x6" strip, centered, on each side of the towing head ii. On all towbars, place a 2"x12" strip on each side of the towbar, 32" from the back of the head iii. On all towbars, place a 1"x12" strip on each side of the towbar, on the lunette side of the red stripe at the ground stop skid H. Stencil: BAR / Inventory # (Exact position may vary by bar type) GEPM Page 40

42 2.26 BAGGAGE TRACTOR, ELECTRIC - TYPICAL I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Apply Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. All Letters & Numbers: White on Blue 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Both Sides) White Reflective B. Decal or Stencil: Unit Number 4 Tall (Both Sides) C. Reflectors: Red/ White Reflectors 2 x12 on all four corners Wrap rear corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: GSE Approach Pattern" ( CPN / ) G. Decal: CAUTION: High Voltage located at the connector (CPN ) H. Decal: CAUTION: Stay clear while operating inching device (only for units with inching capability) (CPN ) I. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) J. Decal: No Smoking (CPN / ) at vicinity of battery lid area (both sides if applicable) K. Decal: Seat Belt must be Worn (CPN ) GEPM Page 41

43 2.27 BAGGAGE TRACTOR, INTERNAL COMBUSTION DRIVEN, TYPICAL I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Apply Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue, 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: GEPM Page 42

44 A. Decal: AA Logo (CPN / ) White Reflective (Centered on rear) and (CPN / ) (Centered on top front grill) B. Decal or Stencil: Unit Number 4 Tall. (Both sides of Hood) C. Reflectors: Red/ White 2 x12 (CPN ) / Center on bends of front Grille as shown/ Two reflectors above each side of cab / Wrap reflector on rear corner red on back white on side D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: GSE Approach Pattern" ( CPN / ) G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) H. Decal: Seat Belt must be Worn (CPN ) I. Lower Left Corner of Rear Bumper can be used for Additional Numbering Needs*( MAX(5) 4 Numbers or Letters.) GEPM Page 43

45 2.28 BAGGAGE TRACTOR NO CAB TYPICAL I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Apply Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) White Reflective (on rear of fuel tank) and (CPN / ) (Centered top of front grille) B. Decal or Stencil: Unit Number 4 Tall (Both sides of Hood) C. Reflectors: Red/ White Reflectors on sides of dash/ front of grille and rear of bumper corners (CPN ) D. Decal: Seat Belt Must Be Worn (CPN ) E. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: F. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) G. Decal: GSE Approach Pattern" ( CPN / ) H. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) LOWER LEFT CORNER OF REAR BUMPER CAN BE USED FOR ADDITIONAL NUMBERING NEEDS GEPM Page 44

46 2.29 CARGO HIGH SPEED TRACTOR, TYPICAL I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Add Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins 3. AA Decals and Markings: A. Decal: AA Logo ( / ) White Reflective (Both sides) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) Wrap reflector on rear corner red on back white on side D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: GSE Approach Pattern" ( CPN / ) H. Decal: Seat Belt must be Worn (CPN ) GEPM Page 45

47 2.30 AIRCRAFT PUSH OUT TRACTOR, GT35 I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Apply Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue VII. Designated walk areas: Apply Non-Skid if needed VIII. Rear OF Tractor: CHEVRON Reflective tape (CPN / )or vinyl graphic (CPN ) 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) White Reflective (Both Sides) B. Decal or Stencil: Unit Number 4 Tall (Both Sides) C. Reflectors: Red/White Reflectors 2 x12 (CPN ) (Place all Four Corners as Shown) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: (Place On Dash) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) (Place On Dash) F. Decal: Pushout Tractor Matrix Placards (refer to SA ) for model specific decal(s). Refer to the Advisory for exact installation locations both in cab and chassis G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) (Place Above Tires) H. Decal: Seat Belt must be Worn (CPN ) (Place on Dash) I. Decal: Pushback Verbiage (CPN ) (Place on Dash) GEPM Page 46

48 2.31 AIRCRAFT PUSH OUT TRACTOR, HOUGH I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Apply Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue VII. Designated walk areas: Apply Non-Skid if needed VIII. Rear OF Tractor: CHEVRON Reflective tape (CPN / )or vinyl graphic (CPN ) 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) White Reflective (Both sides) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Pushout Tractor Matrix Placards (refer to SA ) for model specific decal(s). Refer to the Advisory for exact installation locations both in cab and chassis G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) H. Decal: Seat Belt must be Worn (CPN ) I. Decal: Pushback Verbiage (CPN ) GEPM Page 47

49 2.32 AIRCRAFT PUSH OUT TRACTOR-TYPICAL I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Apply Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. Safety Rails: Yellow VII. All Letters & Numbers: White on Blue VIII. Designated walk areas: Apply Non-Skid if needed IX. Rear OF Tractor CHEVRON Reflective tape (CPN / ) or vinyl graphic (CPN )2- piece for SMALL push out tractors and (CPN ) 3-piece for LARGE push out tractors. 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings A. Decal: AA Logo ( / )(Both sides) Note: smaller Push tractors use (CPN / ) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) GEPM Page 48

50 F. Decal: Pushout Tractor Matrix Placards (refer to SA ) for model specific decal(s). Refer to the Advisory for exact installation locations both in cab and chassis G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) I. Decal: Seat Belt must be Worn (CPN ) J. Decal: Pushback Verbiage (CPN ) GEPM Page 49

51 2.33 PUSH TRACTOR TUG I. Chassis: New American Blue II. Hitch: Yellow III. Interior: Add Non-skid to floors and pedals as needed IV. Wheels: AA Gray V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. Safety Rails: Yellow VII. All Letters & Numbers: White on Blue VIII. Designated walk areas: Apply Non-Skid as needed IX. Rear OF Tractor: CHEVRON Reflective tape or vinyl graphic (CPN ) 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Both sides) White Reflective B. Decal or Stencil: Unit Number 4 Tall (Both Sides) C. Reflectors: Red/White Reflectors 2 x12 on front wrap around corner red on side white on front / on rear place on sides far back as possible red side towards rear (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Pushout Tractor Matrix Placards (refer to SA ) for model specific decal(s). Refer to the Advisory for exact installation locations both in cab and chassis G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) I. Decal: Seat Belt must be Worn (CPN ) J. Decal: Pushback Verbiage (CPN ) GEPM Page 50

52 2.34 AIRCRAFT PUSH OUT TRACTOR (TOWBARLESS)-TYPICAL I. Exterior: New American Blue II. Hitch: Yellow III. Wheels: AA Gray IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue VI. Designated walk areas: Apply Non-skid if needed 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) GEPM Page 51

53 D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Towbar Disconnect (CPN ) H. White or Red Centering Line 3 wide minimum (if required per OEM) I. Decal: Pushout Tractor Matrix Placards (refer to SA ) for model specific decal(s). Refer to the Advisory for exact installation locations both in cab and chassis J. Decal: Seat Belt must be Worn (CPN ) K. Decal: Pushback Verbiage (CPN ) GEPM Page 52

54 2.35 HIGH-SPEED TOWBARLESS TRACTOR-TYPICAL I. Exterior: International Orange II. Hitch: Yellow III. Wheels: AA Gray IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: Blue on Orange 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) B. Decal or Stencil: Unit Number 4 Tall C. Factory installed reflectors D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 53

55 2.36 HIGH LIFT TRUCK-TYPICAL I. Exterior: AA White II. Body Panels: Galvanized or Stainless (Do Not Paint) i. Do not paint Corrugated polished aluminum or fiberglass body with molded-in color III. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels IV. Outriggers, perimeter guards: Yellow V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) X. Hitch: Yellow XI. All Letters & Numbers: Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo doors ( / ) (Centered on Both Doors) / Box (CPN / )(centered middle of box) B. Decal or Stencil: Unit Number 4 Tall (lower rear corners of box) C. Reflectors: Red/ White Reflectors 2 x12 on all four corners and rear lower frame (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) GEPM Page 54

56 ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Warning: Do Not Elevate This Platform When Wind Gusts Exceed 35 Knots (40 MPH) (CPN / ). Place at all control panels. G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only)(above tires) (CPN ) H. Decal: Seat Belt must be Worn (CPN ) I. Decal: CAUTION Stand Clear of Outriggers to Avoid Crushing Injury (CPN ) GEPM Page 55

57 2.37 LAVATORY SERVICE TRUCK- NON VACUUM-TYPICAL I. Exterior: Commercial chassis cab White rear lav-body Blue / Non-Commercial Chassis all Blue II. Body Panels: Galvanized or Stainless (Do Not Paint) Note: Do not paint Corrugated polished aluminum or fiberglass body with molded-in color III. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Centered on Both doors) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: Red/White Reflectors 2 x12 all four corners (CPN ) GEPM Page 56

58 D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal or stencil: LAVATORY SERVICE, 4 Lettering (CPN ) H. Decal: Warning: Do Not Elevate This Platform When Wind Gusts Exceed 35 Knots (40 MPH); (CPN / ) at control panels (lift units only) I. Decal: Seat Belt must be Worn (CPN ) GEPM Page 57

59 2.38 LAVATORY SERVICE TRUCK- Vacuum (Vestergaard VTS) I. Exterior: Cab AA White/ Lav Body New American Blue II. Body Panels: Galvanized or Stainless (Do Not Paint) III. Note: Do not paint corrugated polished aluminum or fiberglass body with molded-in color III. Lift: Unpainted IV. Wheels: AA Gray V. Front Bumper: Yellow VI. Letters & Numbers: White on Blue, Blue on White VII. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) 1. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 2. AA Decals and Markings: GEPM Page 58

60 A. Decal: AA Logo (CPN / )(Both sides) Color decal for White Tank, (CPN / )White decal for Blue Tank B. Decal or Stencil: Unit Number 4 Tall White on Blue, Blue on White (Both sides) C. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) D. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) E. Decal: Lift/waste-gate warning light placard Light is illuminated if platform is raised or dump valve is open (OEM Decal) F. Long Strips size 126 x 2.5 blue & red reflective vinyl (order from TGI) G. Short Strips 43.5 x2.5 blue & red reflective vinyl (order from TGI) H. Decal: or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) I. Decal or stencil: LAVATORY SERVICE, 4 Lettering (CPN ) J. Decal: Warning: Do Not Elevate This Platform When Wind Gusts Exceed 35 Knots (40 MPH); (CPN / ) at control panels K. Placard: Diesel Emission Fluid (DEF) Placard/Pate over DEF fill port (Sage Part #DEFTCP/VESTDEFTC) L. Placard: Confined Space, Do Not Enter (Sage Part #CS25X8PLACA) M. Decal: Seat Belt must be Worn (CPN ) GEPM Page 59

61 2.39 POTABLE WATER SERVICE TRUCK-TYPICAL I. Exterior: AA White II. Body Panels: Galvanized or Stainless (Do Not Paint) III. Wheels: AA Gray IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) ( Centered on Both doors) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Warning: Do Not Elevate This Platform When Wind Gusts Exceed 35 Knots (40 MPH); (CPN / ) at control panels (lift units only) H. Decal: Seat Belt must be Worn (CPN ) I. Decal: Drinking Water (CPN ) GEPM Page 60

62 2.40 BOBTAIL-TYPICAL I. Exterior: AA White II. Body Panels: Galvanized or Stainless (Do Not Paint) III. Wheels: AA Gray IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) ( Centered on Both doors) B. Decal or Stencil: Unit Number 4 Tall (Towards Rear Both Sides) C. Reflectors: Red/White Reflectors 2 x12 ( Wrap around corners) (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Seat Belt must be Worn (CPN ) G. Decal: Gasoline (CPN ) / Diesel (CPN ) H. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 61

63 2.41 PANEL/STEP VAN-TYPICAL I. Exterior: AA White II. Body Panels: Galvanized or Stainless (Do Not Paint) a. Do not paint corrugated polished aluminum or fiberglass body with molded-in color. III. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Centered on both sides) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: : Red/White (CPN ) Not needed on licensed vehicles D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must Worn (CPN ) GEPM Page 62

64 2.42 PICK-UP TRUCK-TYPICAL I. Exterior: AA White II. Liftgate/steel bed protection: Gloss Black III. Body Panels: Galvanized or Stainless (Do Not Paint) a. Do not paint corrugated polished aluminum or fiberglass body with molded-in color. IV. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) ( Centered on Both doors) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: : Red/White (CPN ) Not needed on licensed vehicles D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) H. Decal: Warning never fill gas containers in bed (CPN )(locate inside rear of bed). GEPM Page 63

65 2.43 WRECKER / SERVICE TRUCK-TYPICAL I. Exterior: AA White II. Body Panels: Galvanized or Stainless (Do Not Paint) Do not paint corrugated polished aluminum or fiberglass body with molded-in color. III. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. Wheel Cradles /Tow-bar: Yellow VI. All Letters & Numbers: White on Blue, Blue on White 4. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins 5. AA Decals and Markings: A. Decal: AA Logo ( / ) (Centered on Both doors) B. Decal or Stencil: Unit Number 4 Tall (Both Sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: iv. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) v. Decal: Test Brakes Before Approaching Aircraft (CPN / ) vi. Decal: Set Parking Brake When Not in Use (CPN / ) D. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 64

66 2.44 BOX VAN TRUCK-TYPICAL I. Exterior: AA White II. Body Panels: Galvanized or Stainless (Do Not Paint) a. Do not paint corrugated polished aluminum or fiberglass body with molded-in color. III. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins 3. AA Decals and Markings: A. Decal: AA Logo (CPN / )(Centered on Both Doors) / (CPN / ) (Centered Middle of box both sides) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: : Red/White (CPN ) Not needed on licensed vehicles D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 65

67 2.45 STAKE BED TRUCK TYPICAL I. Exterior: Cab AA White / Stake bed Gloss Black / Stake bed side panels AA White II. Liftgate: Gloss Black III. Body Panels: Galvanized or Stainless (Do Not Paint) a. Do not paint corrugated polished aluminum or fiberglass body with molded-in color. IV. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / )(Centered on Both doors) B. Decal or Stencil: Unit Number 4 tall Letters C. Reflectors: : Red/White (CPN ) Not needed on licensed vehicles D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals I. Decal: You Are Responsible for the Safe Operation of This Vehicle (CPN / ) II. Decal: Test Brakes Before Approaching Aircraft (CPN / ) III. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 66

68 2.46 BOOM - LIFT-TYPICAL I. Exterior: Leave Factory Finish unless previously painted then paint New American Blue II. Body Panels: Galvanized or Stainless (Do Not Paint) Do not paint corrugated polished aluminum or fiberglass body with molded-in color. III. Wheels: AA Gray IV. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) V. All Letters & Numbers: White on Blue, Blue on White 1 OEM Safety Decals per the OEM Manual and/or Service Bulletins. 2. AA Decals and Markings: A. Decal: AA Logo ( / ) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Do Not Elevate Boom /Basket When Wind Gusts Exceed 40 Knots (46 MPH). (CPN / ) G. Decal: Warning harness must be worn (CPN ) GEPM Page 67

69 2.47 TRUCK MOUNTED MAINTENANCE LIFT TYPICAL Exterior: New American Blue / Cab AA White I. Body Panels: Galvanized or Stainless (Do Not Paint) II. Do not paint corrugated polished aluminum or fiberglass body with molded-in color. III. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels IV. Outriggers: Yellow V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue, Blue on White 1. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 2. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Centered on Both doors) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Do Not Elevate Boom /Basket When Wind Gusts Exceed 40 Knots (46 MPH). (CPN / ) G. Decal or Stencil: Tire Pressure #, ½ Lettering (CPN ) H. Decal: CAUTION Keep Feet Clear of Stabilizer when in Operation(CPN / ) I. Decal: Seat Belt must be Worn (CPN ) J. Decal: Warning harness must be worn (CPN ) GEPM Page 68

70 2.48 MAINTENANCE ENTRY STAND TYPICAL 1 Color Scheme: I. Exterior: Factory Color II. Do not paint Corrugated polished aluminum or fiberglass body with molded-in color need not be painted III. Wheels: AA Gray IV. Hand Rails,Outriggers, Tow-Bar V. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins A. Decal: AA Logo (CPN / ) B. Decal or Stencil: Unit Number 4 Tall GEPM Page 69

71 2.49 MAINTENANCE PLATFORM LIFT TYPICAL I. Exterior: New American Blue II. Do not paint Corrugated polished aluminum or fiberglass body with molded-in color need not be painted III. Wheels: AA Gray IV. Outriggers: Yellow V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / F. Decal: Do Not Elevate Boom /Basket When Wind Gusts Exceed 40 Knots (46 MPH). (CPN / ) G. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) H. Decal: Seat Belt must be Worn (CPN ) I. Decal: Do Not operate lift controls from Drivers compartment (CPN ) GEPM Page 70

72 2.50 MAINTENANCE/ WHEEL CHAIR PLATFORM LIFT ELECTRIC CHARLATTE CHASSIS 1 Color Scheme: VI. Exterior: White VII. Do not paint Corrugated polished aluminum or fiberglass body with molded-in color need not be painted VIII. Wheels: AA Gray IX. Outriggers / Handrails: Yellow X. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) XI. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: Do Not Elevate Boom /Basket When Wind Gusts Exceed 40 Knots (46 MPH). (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 71

73 2.51 MAINTENANCE LIFTS ELECTRIC-TYPICAL I. Exterior: Factory finish unless painted before then use New American Blue II. Body Panels: Galvanized or Stainless (Do Not Paint) III. Do not paint corrugated polished aluminum or fiberglass body with molded-in color. IV. Wheels: AA Gray 2. Color identified per GEPM Page 5, Ref. GSER GN (latest revision 3. All Letters & Numbers: White on Blue, Blue on White A. Decal: AA Logo ( / ) FOR BLUE UNITS USE ( CPN / ) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/ White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal: Do not move or position without guide person (CPN ) GEPM Page 72

74 2.52 SUV - TYPICAL I. Exterior: AA White II. Wheels: AA Gray or Factory Standard Note: Do not paint chrome and aluminum wheels III. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IV. All Letters & Numbers: Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Centered on both Doors) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: : Red/White (CPN ) Not needed on licensed vehicles D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Test Brakes Before Approaching Aircraft (CPN / ) iii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 73

75 2.53 UTILITY VEHICLE, MAINTENANCE-TYPICAL I. Exterior: New American Blue II. Body Panels: Galvanized or Stainless (Do Not Paint) a. Do not paint corrugated polished aluminum or fiberglass body with molded-in color. III. Interior: Add Anti-skid to floors and pedals as needed IV. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels V. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) VI. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Centered on both Doors) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 74

76 2.54 UTILITY CART-TYPICAL I. Exterior: Factory Color until repaint is needed then paint New American Blue II. Wheels: AA Gray Note: Do not paint chrome and aluminum wheels III. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IV. All Letters & Numbers: White on Blue 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) B. Decal or Stencil: Unit Number 4 Tall C. Reflectors: Red/White Reflectors 2 x12 on all four corners (CPN ) D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 75

77 2.55 UTILITY VAN TYPICAL: I. Exterior: AA White II. Wheels: White or Factory Standard Note: Do not paint chrome and aluminum wheels III. Fluid Fill Ports: Color identified per GEPM Page 5. GSER GN (latest revision) IV. All Letters & Numbers: Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo (CPN / ) (Centered on Both doors) B. Decal or Stencil: Unit Number 4 Tall (Both sides) C. Reflectors: : Red/White (CPN ) Not needed on licensed vehicles D. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Set Parking Brake When Not in Use (CPN / ) E. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) G. Decal: Seat Belt must be Worn (CPN ) GEPM Page 76

78 2.56 SPRINTER VAN TYPICAL: 4. Color Scheme: V. Exterior: AA White VI. Wheels: White or Factory Standard Note: Do not paint chrome and aluminum wheels VII. Fluid Fill Ports: Color identified per GEPM Page 5. GSER GN (latest revision) VIII. All Letters & Numbers: Blue on White 5. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 6. AA Decals and Markings: H. Decal: AA Logo (CPN / ) (Centered on Both doors) I. Decal or Stencil: Unit Number 4 Tall (Both sides) J. Reflectors: : Red/White (CPN ) Not needed on licensed vehicles K. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: iii. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) iv. Decal: Set Parking Brake When Not in Use (CPN / ) L. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) M. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) N. Decal: Seat Belt must be Worn (CPN ) GEPM Page 77

79 2.57 MINI BUS TYPICAL : LEFT SIDE 1of 2 I. Exterior: AA White II. Wheels: AA Grey or Factory Standard Note: Do not paint chrome and aluminum wheels III. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IV. All Letters & Numbers: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) B. Decal or Stencil: Unit Number 4 Tall C. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Set Parking Brake When Not in Use (CPN / ) D. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) E. Decal: Seat Belt must be Worn (CPN ) (Note: for driver only) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 78

80 2.58 MINI BUS TYPICAL: RIGHT SIDE 2 of 2 I. Exterior: AA White II. Wheels: AA Grey or Factory Standard a. Note: Do not paint chrome and aluminum wheels III. Fluid Fill Ports: Color identified per GEPM Page 5, Ref. GSER GN (latest revision) IV. All notes: White on Blue, Blue on White 2. All required OEM Safety Decals per the OEM Manual and/or Service Bulletins. 3. AA Decals and Markings: A. Decal: AA Logo ( / ) B. Decal or Stencil: Unit Number 4 Tall C. Decal: 3 in 1 Safety Decal (CPN / ) or individual decals: i. Decal: You Are Responsible For The Safe Operation Of This Vehicle (CPN / ) ii. Decal: Set Parking Brake When Not in Use (CPN / ) D. Decal: This Vehicle Is Intended For Authorized Company Use Only. Misuse Of This Vehicle Is In Violation of AA Regulations (CPN / ) E. Decal: Seat Belt must be Worn (CPN ) (Note: for driver only) F. Decal or Stencil: Tire Pressure #, ½ Lettering (pneumatic tires only) (CPN ) GEPM Page 79

81 FOR DECALS Contacts Endagraph, Inc. Contact: Terry E. Lollar, CEO Address: 9000 Corporate Circle Export, PA Phone: ext. 201 Fax: FOR LOGO S TGI-DIRECT Contact: Kelly Priest Kelly@craftmarkid.com Address: 3212 S Cravens Road FT Worth, Texas Phone: Fax: GEPM Page 80

82 3.0 LOGO DECALS: 3 Horizontal - COLOR CPN / HORIZONTAL- COLOR CPN / HORIZONTAL COLOR CPN / STACKED COLOR CPN / STACKED - COLOR CPN / GEPM Page 81

83 9 STACKED COLOR CPN / STACKED COLOR CPN / HORIZONTAL WHITE CPN / HORIZONTAL-WHITE CPN / HORIZONTAL-WHITE CPN / STACKED-WHITE CPN / GEPM Page 82

84 6 STACKED-WHITE CPN / STACKED-WHITE CPN / STACKED-WHITE CPN / BAG CART ROOF- WHITE CPN / GEPM Page 83

85 3.1 DECALS: NUMBERS / LETTERS WHITE NUMBERS AND LETTERS The following is a list of the White 4 Numbers and Letters LETTER/NUMBER CPN LETTER/NUMBER CPN A B C D E F * G H I * J * K L M N O* P Q R S T U V W X Y Z * Numbers 6 and 9 are the same. * Letter O and Number 0 are the same. GEPM Page 84

86 BLUE NUMBERS AND LETTERS The following is a list of the Blue 4 Numbers and Letters LETTER/NUMBER CPN LETTER/NUMBER CPN A B C D E F * G H I * J * K L M N O* P Q R S T U V W X Y Z * Numbers 6 and 9 are the same. * Letter o and Number 0 are the same GEPM Page 85

87 NUMBERS 2.5 WHITE THESE NUMBERS ARE TO BE USED IN CONJUCTION WITH THE TARE WT. DECAL NUMBER - 2 1/2 INCH WHITE NUMBER NUMBER - 2 1/2 INCH WHITE NUMBER NUMBER - 2 1/2 INCH WHITE NUMBER NUMBER - 2 1/2 INCH WHITE NUMBER NUMBER - 2 1/2 INCH WHITE NUMBER NUMBER - 2 1/2 INCH WHITE NUMBER 6 & NUMBER - 2 1/2 INCH WHITE NUMBER NUMBER /2 INCH WHITE NUMBER 8 GEPM Page 86

88 GEPM Page 87

89 GEPM Page 88

90 GEPM Page 89

91 GEPM Page 90

92 SAGE DASHDECAL GEPM Page 91

93 GEPM Page 92

94 GEPM Page 93

95 GEPM Page 94