PART 3 VEHICLE REGULATIONS

Transcription

1 PART 3 VEHICLE REGULATIONS 3.1 Definitions In this Part the words and phrases shown in bold italics shall have the definitions and meanings assigned to them in the Commercial Transport Act and Motor Vehicle Act and regulations thereto as amended, revised, consolidated or replaced from time to time. 3.2 Vehicle Regulations Prohibitions Oversized vehicles. Except as authorized by an overweight or oversize vehicle permit no person shall drive or operate on a highway: (e) (f) (g) (h) Maximum width a passenger vehicle so loaded that any part of the load extends beyond the sides of the vehicle or more than 185 centimetres beyond the back of the vehicle; Pneumatic tires a vehicle, other than a horse-drawn vehicle, the wheels of which are not equipped with pneumatic tires; Solid Tires a vehicle equipped with solid tires, the thickness of which between the rim of the wheel and the surface of the highway is less than 32 millimetres; Spikes, Cleats, etc. a vehicle having wheels, or tracks constructed or equipped with projecting spikes, cleats, ribs, clamps, flanges, lugs, or other attachments or projections which extend beyond the tread or traction surface of the wheel, tread, or track but excluding tire chains of reasonable proportions when required for safety and winter studded tires between October 1 st and April 30 th ; Solid tire over 20 km/h a solid tired vehicle at a greater rate of speed than 20 km/h; Pole Trailer an unloaded vehicle and pole trailer at a greater rate of speed then 60 km/h, unless the pole-trailer is carried on the towing vehicle; Secure Load a vehicle unless it is so constructed and loaded as to prevent any of its load: (i) from shifting or swaying in such a manner as to affect the operation of the vehicle; or (ii) from dropping, sifting, leaking, or otherwise escaping therefrom. This subsection does not apply to material dropped for the purpose of securing traction, and water or other substances sprinkled on a roadway for cleaning or maintaining the roadway; or Load Covering a vehicle with any load unless the load is covered with a securely fastened tarpaulin or other cover so as to prevent load from becoming loose, detached, or in any manner hazardous to other users of the highway. Part 3 Vehicle Regulations August 26,

2 3.2.2 Prohibitions Overweight vehicles. Except as authorized by an overweight or oversize vehicle permit no person shall drive or operate a vehicle on a highway: Gross vehicle weight when the gross vehicle weight of the commercial vehicle exceeds its licensed gross vehicle weight; Axle Weight when the weight on an axle, group of axles or axle unit exceeds the weight permitted by Section 3.3 of this Part; Vehicle Dimensions when the dimensions of the commercial vehicle do not conform to Section 3.3 of this Part (i) with load included; and (ii) without load; or Distances between axles when the distances between axles, groups of axles or axle units do not conform with Section 3.3 of this Part. (e) Obey Posted Weight Restrictions when a traffic control device restricts and/or reduces ther permitted weight limits. 3.3 Size and Weight Restrictions Exceptions Subsections to inclusive of this Part do not apply to a person who is driving or operating a commercial vehicle engaged in the construction of, or operating within the boundaries of, a highway construction project. Subsection of this Part does not apply to a person who is driving or operating: (i) an implement of husbandry on a highway during the hours of daylight, or (ii) a vehicle registered in the name of the Ministry of Transportation & Highways, or the City which is operated for the purposes of road maintenance or snow removal, or a vehicle registered in the name of a company that has a contract with the Ministry of Transportation & Highways, or the City, for the purpose of road maintenance or snow removal and which is being operated for the same. Where the overall width of an implement of husbandry for which a person is exempted under Subsection of this Part is 3.7 metres or more, a sign as described in the Commercial Transport Act shall be mounted on the front and a flag as described in the Commercial Transport Act shall be mounted on each of the 4 corners of the implement of husbandry. Part 3 Vehicle Regulations August 26,

3 3.3.2 Overweight or Oversize Vehicle Permit. The Engineer may issue an overweight or oversize vehicle permit, in accordance with the conditions outlined in Schedule C of this Bylaw, authorizing the driving or operation on a highway of a commercial vehicle that does not conform to Subsections to inclusive of this Part. Prior to issuance of such a permit, the permit fee as outlined in Schedule A to this Bylaw, shall be paid to the City. No person shall use an overweight or oversize vehicle permit for the driving or operation of a vehicle other than the vehicle for which such permit was issued or on a date other than that specified in the permit. Unless expressly permitted by the conditions of an overweight or oversize vehicle permit, no person shall drive or operate an oversize vehicle or load on a Sunday or a general holiday Logging truck Weight Allowances. Despite the provisions of this Bylaw, but in accordance with the requirements of this subsection, a person may drive or operate on a highway a vehicle or combination of vehicles transporting logs or poles if the amount of excess gross weight does not exceed the following: during that period between March 2nd and November 30th of a calendar year: (i) single axle kilograms, (ii) tandem or tridem axles - 1,100 kilograms, combination of vehicles - 1,500 kilograms. during that period between December 1st of a calendar year and March 1st in the next calendar year: (i) single axle kilograms, (ii) tandem or tridem axles - 1,500 kilograms, combination of vehicles - 2,500 kilograms. Despite Subsections and of this Part, if a posted sign on a highway restricts vehicles by weight, the posted restrictions apply Weighing. The operator of a vehicle on a highway, when so required by a Peace Officer, or by any person authorized by the Engineer, shall: stop the vehicle at the time and place specified by such Peace Officer, or authorized person, for the purpose of weighing the whole vehicle, or part thereof, by means of stationary or portable scales, measuring the dimensions of the vehicle and load; measuring and inspecting the tires thereon, inspecting the load carried, or for any other purpose under this Bylaw; stop the vehicle if the vehicle or the load it is carrying is, in the opinion of the Peace Officer, or the authorized person, unsafe for operation on the highways and shall fix the defect in the vehicle or secure the load, as the case may be, before proceeding; drive the vehicle onto the nearest public or Ministry of Attorney General or City stationary or portable scales for the purpose of weighing the vehicle and load; or re-arrange the load on the vehicle, or remove the whole or part of the load from the vehicle, in order to comply with the provisions of this Bylaw or a overweight or oversize vehicle permit before continuing to drive or operate the vehicle. Part 3 Vehicle Regulations August 26,

4 3.3.5 Report to Scales. Except for operators of commercial vehicles of a licensed gross vehicle weight not exceeding 5,500 kilograms, the operator of a vehicle on a highway, when directed by a traffic sign on the highway to report to scales, shall drive the vehicle onto the scales for the purpose of weighing the whole vehicle, or part thereof, by means of stationary or portable scales, measuring the dimensions of the vehicle and load, measuring and inspecting the tires thereon, inspecting the load carried, or for any purpose under this Bylaw Obey Posted Signs. Notwithstanding any of the provisions of this Bylaw or of an overweight or oversize vehicle permit the maximum height, length or width of a vehicle, or vehicle and load, allowable on a highway or portion of a highway, where the maximum is stated by a sign posted by the Engineer, shall be as indicated by that sign Bridge Restrictions. No person shall, without an overweight or oversize vehicle permit drive or operate a vehicle or combination of vehicles over a bridge if the gross weight on an axle or group of axles or the gross vehicle weight is in excess of a load limit posted by the Engineer on or adjacent to that bridge Vehicle Height. No person shall, without an overweight or oversize vehicle permit drive or operate a vehicle having a height, including its load, in excess of 4.15 metres, measured from the surface of the road Vehicle Width. No person shall, without an overweight or oversize vehicle permit, drive or operate on a highway a vehicle having a total outside width, including its load, in excess of 2.6 metres, but not including the following as part of that width: loose hay, straw or fodder projecting over the sides of the vehicle to a total outside width not in excess of 3.1 metres; one or more mirrors, fitted for the purpose of conforming to the requirements of the Motor Vehicle Act Regulations, which do not extend more than 20 centimetres on each side beyond the total width of vehicle and load otherwise permitted by this section; or an Anti-splash and spray device, load securement device, ladder, glad hand, air connector, electrical connector, hydraulic connector, clearance lamp or dangerous goods placard if the device, ladder, glad hand, air connector, electrical connector, hydraulic connector, lamp or placard does not extend more than 10 centimetres on each side beyond the widest part of the vehicle and its load Vehicle Axle width Subject to Subsection of this Part, no person shall, without an overweight or oversize vehicle permit, drive or operate a TAC semi-trailer or full trailer unless the distance across the outside of the tires on each single axle, each tandem axle and each tridem axle is: (i) where the width of the semi-trailer or full trailer body is 2.5 metres or more, not less than 2.5 metres nor more than 2.6 metres, and (ii) where the width of the semi-trailer or full trailer body is less than 2.5 metres, not less than 2.4 metres. Part 3 Vehicle Regulations August 26,

5 Where a semi-trailer or full trailer was manufactured prior to August 31 st, 1988, and the running gear has not been totally replaced, the width across the outside of the tires may be less than that required in Subsection (i) and any axles which are added to the existing running gear may be of a width equal to that running gear. Notwithstanding Subsection of this Part, no person shall, without an overweight or oversize vehicle permit, drive or operate any semi-trailer, full trailer or pole trailer manufactured after December 31 st, 1993, unless the distance across the outside of the tires on each axle of the vehicle is not less than 2.5 metres nor more than 2.6 metres Vehicle Length This section does not apply to a driver or operator of a TAC vehicle. operate (i) (ii) (iv) (v) except as provided in Subsections (ii) and of this Part, a single vehicle having an overall length, including its load, in excess of 12.5 metres, a trailer having an overall length in excess of 12.5 metres, but not including the following as part of that length: (1) an Air deflector, heater or refrigerator unit attached to the front of the trailer, (2) the draw bar of the trailer if the draw bar articulates in the horizontal plane relative to the main load-carrying structural component of the trailer, (3) non-load-carrying equipment such as an air connector, electrical connector, hydraulic connector, roller, pick-up plate, bumper, ladder, glad hand, load securement device or dangerous goods placard if the connector, roller, plate, bumper, ladder, glad hand, device or placard does not extend more than 30 centimetres beyond the front or 10 centimetres beyond the rear of the vehicle; or (4) a platform mounted on the front upper portion of the trailer if the platform is used exclusively to assist in the installation and/or securing of load securement devices. a semi-trailer: (1) having an overall length in excess of metres, or (2) having more than 2 axles the tires of which are in contact with the ground, having an overall length in excess of 14 metres, but not including as part of that length anything described in Subsections (ii)(1), (3) or (4) of this Part. subject to Subsection of this Part, a combination of 2 or more vehicles having an overall length in excess of 20 metres including their load. a bus with an articulation point between the passenger carrying sections of the bus unless: (1) the overall length of the bus does not exceed 20 metres, (2) the distance from the articulation point to the front or rear of the bus does not exceed 12.5 metres, and Part 3 Vehicle Regulations August 26,

6 (vi) (3) movement of passengers between the articulated sections of the bus is possible at all times while the bus is being operated on a highway. after January 1 st, 1993, a 3 vehicle combination consisting of a truck and 2 trailers, or a logging truck combination which includes 2 pole trailers. Subsection (iv) of this Part does not apply where the combination of vehicles: (i) (ii) is a combination of 2 vehicles that has a single articulation point, has an overall length, including its load, of not more than 21.5 metres and is carrying a load of logs, woodpoles or wood pilings and the length of the load cannot be reduced without cutting the wood; is a combination of vehicles that contains more than one articulation point and has an overall length, including its load, of not more than 23 metres, or is a combination of vehicles that: (1) contains a licensed booster axle assembly mounted to the rear of a semi-trailer lowbed, and (2) has an overall length including its load, of not more than 23 metres TAC vehicle length This section applies ONLY to drivers or operators of TAC vehicles. operate a truck tractor in combination with a single semi-trailer unless: (i) the overall length of the semi-trailer is not more than 16.2 metres, but not including as part of that length anything described in subsections (ii) (1), (3), or (4) of this Part, and (ii) the wheelbase of the semi-trailer is not less than 6.25 metres and not more than 12.5 metres. operate an A train or C train unless: (i) the distance from the front of the lead semi-trailer to the rear of the full trailer is not more than 18.5 metres, but not including as part of that length anything described in subsections (ii)(1),(3), or (4) of this Part, and (ii) the wheelbase of the lead semi-trailer or the following full trailer is not less than 6.25 metres nor more than 12.5 metres. No person shall, without an overweight or oversize vehicle permit drive or operate a B train unless: (i) the distance from the front of the lead semi-trailer to the rear of the second semi-trailer is not more than 20 metres, but not including as part of that length anything described in subsections (ii)(1),(3), or (4) of this part, (ii) except for a vehicle referred to in Subsection of this Part, the wheelbase of the lead semi-trailer is not less than 6.25 metres no more than 12.5 metres, and the wheelbase of the second semi-trailer is not less than 6.25 metres no more than 12.5 metres. Part 3 Vehicle Regulations August 26,

7 (e) operate: (i) (ii) (iv) (v) (vi) (vii) a truck tractor having a wheelbase in excess of 6.2 metres, a bed truck having a wheelbase in excess of 10.0 metres, a truck tractor in combination with a single semi-trailer or a jeep and semi-trailer lowbed as allowed in subsection of this Part, having an overall length, including its load, in excess of 23 metres, an A train, B train, or C train having an overall length, including its load, in excess of 25 metres, a full trailer having an overall length in excess of 12.5 metres but not including as part of that length anything described in subsections (ii)(1), to (4) inclusive of this part, a combination including 2 semi-trailers having a fifth wheel coupler mounted on the first semi-trailer at a location not within the axle spread of the first semi-trailer, a 3 vehicle combination consisting of a truck tractor, semi-trailer and pony trailer Kingpin Setback This section DOES NOT apply to drivers or operators of TAC vehicles. Except as provided in Subsection of this part, no person shall, without an overweight or oversize vehicle permit, drive or operate a combination of vehicles: (i) that includes a semi-trailer with any part of its body or load forward of the centre of the articulation point by more than a radius of 2.25 metres; or (ii) where the distance from an articulation point to the extreme rear of the vehicle combination exceeds 18 metres, but not including as part of that distance anything described in Subsections (ii)(1), (3) or (4) of this Part. No person shall drive or operate on a highway, without an overweight or oversize vehicle permit, a pole trailer in combination with one other vehicle where the combination of vehicles is carrying a load that projects forward of the vertical axis of rotation of the forward bunk by a radius of more than 3 metres TAC Kingpin Setback and Front Projection This section applies ONLY to drivers or operators of TAC vehicles. operate a semi-trailer or full trailer where a part of the body or load is forward of the centre of the turning axis articulation point by more than a radius of 2 metres. operate a truck tractor or truck where the load, boom, crane or similar object projects more than 1 metres beyond the front wheels, or, if the truck tractor or truck is equipped with a front bumper, more than 1 metres beyond such bumper. Part 3 Vehicle Regulations August 26,

8 Front and Rear Projections This section DOES NOT apply to drivers or operators of TAC vehicles. operate a vehicle or combination of vehicles where: (i) the load, boom, crane or similar object extends more than 1 metres beyond the front wheels, or if equipped with a front bumper, more than 1 metres beyond that bumper; or (ii) subject to Subsection of this Part, the rear projection from the centre of the last axle to a part of the vehicle or load exceeds 5 metres. Subsection (ii) of this Part does not apply where the vehicle or combination of vehicles is a logging truck tractor and pole trailer carrying logs or poles in their natural state and the rear projection from the centre of the last bunk to a part of the vehicle or load does not exceed 5 metres TAC Effective overhang This section applies ONLY to drivers or operators of TAC vehicles. operate any semi-trailer in combination with a truck tractor where the effective overhang on any semi-trailer in the combination exceeds 35% of that semi-trailer s wheelbase Drawbar Length This section DOES NOT apply to a driver or operator of a TAC vehicle. No person shall, without an overweight or oversize vehicle permit drive or operate a combination of vehicles where the length of the drawbar or other connection between 2 of the vehicles exceeds 5 metres, except a combination consisting of only a motor vehicle and a pole trailer TAC Hitch offset This section applies ONLY to a driver or operator of a TAC vehicle. No person shall, without a overweight or overdrive vehicle permit, drive or operate an A train or C train where the hitch offset on the lead semi-trailer exceeds 1.8 metres Load Sharing No person shall, without a overweight or oversize vehicle permit, drive or operate a combination of vehicles where the load is supported by more than one vehicle in combination except: a combination carrying logs, wood poles or wood pilings by means of a pole trailer equipped with a compensating reach; or where the load is supported at an articulation point by a fifth wheel coupler and kingpin, a pintle hook and lunette eye assembly, or a turntable. Part 3 Vehicle Regulations August 26,

9 Axle Groups (e) This section DOES NOT apply to drivers or operators of TAC vehicles. No person shall, without a overweight or oversize vehicle permit, drive or operate on a highway a vehicle or combination of vehicles which has 2 or 3 consecutive axles in contact with the ground, if those axles are not a tandem or tridem axle, unless the first or last axle is a self-steering axle. No person shall drive or operate a tridem pole trailer in combination with a jeep or dog logger. operate on a highway a logging truck with a tridem axle pole trailer where the inter-axle spacing between a Tandem axle and a tridem axle is less than 5.5 metres. No person shall, without an overweight or oversize vehicle permit, drive a logging truck where the inter-axle spacing between 2 steering axles exceeds 185 centimetres TAC Axle unit This section applies ONLY to drivers or operators of TAC vehicles. operate on a highway: (i) a truck tractor in combination with (1) a semi-trailer, on which more than one axle units in contact with the ground, (2) a semi-trailer having a trailer wheelbase of less than 9.5 metres, equipped with a tridem axle having an axle spread of more than 3.1 metres, (3) a trailer converter dolly equipped with a tandem or tridem axle unit, or (ii) except as provided in Subsections and (iv) of this part, and Subsection , a vehicle or combination of vehicles in which the inter-axle spacing (1) between a single axle and any other single axle, between a single axle and a tandem axle, or between a single axle and a tridem axle is less than 3 metres, (2) between 2 tandem axles is less than 5 metres, (3) between a tandem axle and a tridem axle is less than 5.5 metres, (4) between 2 tridem axles is less than 6 metres. operate on a highway (i) a truck tractor equipped with a tridem axle, or (ii) a truck tractor equipped with 2 steering axles. Part 3 Vehicle Regulations August 26,

10 Lift axles No person shall drive or operate on a highway a combination of vehicles in which a control, other than one that locks or unlocks a sliding fifth wheel coupler, is provided (i) for raising or lowering a single axle or group of axles, or (ii) for varying the load on an axle or group of axles other than at a location that is adjacent to that axle or group of axles and not inside the operator s compartment. No person shall drive or operate a TAC vehicle equipped with a lift axle where the tires of the lift axle are in contact with the ground. No person shall drive or operate any pole trailer equipped with a lift axle where the tires of the lift axle are in contact with the ground Self-steering axles operate on a highway in combination with other vehicles a motor vehicle equipped with a self-steering axle where the tires of the self-steering axle are in contact with the ground. operate a TAC vehicle equipped with a self-steering axle where the tires of the self-steering axle are in contact with the ground, except a C dolly may have a self-steering axle Licensed GVW. The maximum licensed gross vehicle weight of a vehicle or combination of vehicles shall not exceed 63,500 kilograms Maximum GVW To determine the maximum allowable gross vehicle weight of a vehicle or combination of vehicles, only those axles that are within the prescribed maximum overall length shall be included. Notwithstanding Subsection of this Part, where a vehicle or combination of vehicles is extended beyond the maximum overall length authorized under this division for the sole purpose of accommodating an oversize or overweight load without any increase in the number of axles, the displaced axles shall be deemed to be within the maximum overall length authorized under this Subsection TAC GVW This section applies ONLY to drivers or operators of TAC vehicles. operate on a highway: (i) a truck tractor in combination with a semi-trailer having a gross vehicle weight in excess of 46,500 kilograms, (ii) an A train or C train having a gross vehicle weight in excess of 53,500 kilograms, Part 3 Vehicle Regulations August 26,

11 (iv) an A train having a single axle on the first semi-trailer and an A dolly axle, with their inter-axle spacing less than 3 metres, and having a combined weight in excess of 17,000 kilograms, or an A train having a tandem axle on the first semi-trailer and an A dolly axle, with their inter-axle spacing less than 3 metres, and having a combined weight in excess of the weights indicated in the Table of Maximum Gross Vehicle Weight for Axle Groups of Subsection (ii) of this part Exemption from weight limitations. The weight limitations imposed by Subsections to inclusive of this Part, shall not apply to vehicles being operated by: the Ministry of Transportation & Highways; or the City; or a company that has a contract with the Ministry of Transportation & Highways, or the City, for the purpose of improving traction of a highway while the vehicle is operated for the distribution of material on the highway for the purpose of improving traction, and (e) travelling to the place on the highway where distribution of the material carried by the vehicle begins; or distributing the material on the highway Tire Loads This section DOES NOT apply to drivers or operators of TAC vehicles. operate on a highway a vehicle loaded so that the gross weight on a tire exceeds (i) 110 kilograms per 1 centimetre of tire width in the case of pneumatic tires, or (ii) 55 kilograms per 1 centimetre of tire width in the case of metal or solid tires TAC Tire Loads This section applies ONLY to drivers or operators of TAC vehicles. operate upon a highway a vehicle so loaded that the gross weight on a tire: (i) exceeds 100 kilograms per 1 centimetre of tire width in the case of pneumatic tires, (ii) exceeds the rated capacity of the tire as rated by the manufacturer of the tire, exceeds 3,000 kilograms, other than a tire attached to the steering axle of (1) a self-loading truck tractor, or (2) a bed truck or truck tractor, equipped with a winch behind the cab, where the truck is being used in oil exploration. Part 3 Vehicle Regulations August 26,

12 Maximum Axle Load and Spacing This section DOES NOT apply to drivers or operators of TAC vehicles. operate on a highway: (i) a vehicle, where an axle carries a gross weight in excess of 9,100 kilograms, or (ii) a vehicle or combination of vehicles having a group of axles within a spacing of 8 metres or less, where the group of axles carries the gross weight indicated in Column 2 of the Table of Maximum Gross Vehicle Weight for Axle Groups opposite the distance between the centres of the first and last axle of the group as indicated in Column 1: TABLE OF MAXIMUM GROSS VEHICLE WEIGHT FOR AXLE GROUPS Column 1 Distance Between the Centres of the First Axle and Last Axle of Any Group of Axles of a Vehicle or Combination of Vehicles Column 2 Maximum gross weight, group of axles Less than 1.00 metres 9,100 kilograms 1.0 metres up to but not including 1.20 metres 16,500 kilograms 1.20 metres up to but not including 1.90 metres 17,000 kilograms 1.90 metres up to but not including 2.30 metres 18,000 kilograms 2.30 metres up to but not including 2.60 metres 19,000 kilograms 2.60 metres up to but not including 3.00 metres 20,000 kilograms 3.00 metres up to but not including 3.40 metres 21,000 kilograms 3.40 metres up to but not including 3.80 metres 22,000 kilograms 3.80 metres up to but not including 4.20 metres 23,000 kilograms 4.20 metres up to but not including 4.60 metres 24,000 kilograms 4.60 metres up to but not including 5.00 metres 25,000 kilograms 5.00 metres up to but not including 5.30 metres 26,000 kilograms 5.30 metres up to but not including 5.70 metres 27,000 kilograms 5.70 metres up to but not including 6.10 metres 28,000 kilograms 6.10 metres up to but not including 6.50 metres 29,000 kilograms 6.50 metres up to but not including 6.90 metres 30,000 kilograms 6.90 metres up to but not including 7.20 metres 31,000 kilograms 7.20 metres up to but not including 7.60 metres 32,000 kilograms 7.60 metres up to but not including 8.00 metres 33,000 kilograms 8.00 metres 34,000 kilograms (iv) a 3 vehicle combination of vehicles where a single steering axle on the truck tractor carries a gross weight in excess of 6,000 kilograms, a 3 vehicle combination of vehicles with a gross vehicle weight in excess of 57,000 kilograms unless (1) the power unit is a truck tractor; and (2) the kingpin of the first semi-trailer is positioned at, or forward of, a point midway between the centre of the 2 rear most axles of the truck tractor, Part 3 Vehicle Regulations August 26,

13 (v) (vi) a 3 vehicle combination of vehicles unless the gross vehicle weight exceeds 11,000 kilograms, or a combination of vehicles having a gross vehicle weight in excess of 63,500 kilograms. Notwithstanding Subsection (v) of this Part, a person does not require an overweight or oversize vehicle permit to drive or operate a 3 vehicle combination of vehicles, the gross vehicle weight of which does not exceed 11,000 kilograms, where the combination consists of: (i) (ii) a motor vehicle, and a towing dolly, and a licensed motor vehicle one axle of which is being carried by the towing dolly. operate a logging truck combination which includes a tridem pole trailer where: (i) (ii) a steering axle, other than on a self-loading motor vehicle, exceeds 5,500 kilograms; or a tandem axle exceeds 17,000 kilograms, or a tridem axle exceeds 24,000 kilograms. (e) operate a self-loading logging truck which includes a tridem pole trailer where the steering axle exceeds 9,100 kilograms TAC Axle Loads and Spacing In this section "self-loading truck tractor" means a truck tractor equipped with a chassis mounted crane, winch or similar device immediately behind the operator s compartment which is used for loading or unloading the vehicle combination. This section applies ONLY to driver or operators of TAC vehicles. operate: (i) a vehicle where the gross axle weight on (1) an axle unit exceeds the axle, suspension or brake manufacturer s rating of that component, (2) the steering axle of a truck tractor other than a self-loading truck tractor, or a bed truck or truck tractor, equipped with a winch behind the cab, where the truck is being used in oil exploration exceeds 5,500 kilograms, (3) a single axle equipped with dual tires exceeds 9,100 kilograms, (4) a tandem axle exceeds 17,000 kilograms, or (5) a tridem axle exceeds 24,000 kilograms. (ii) an A train or C train where the sum of the axle loads on all axles of the full trailer exceeds 16,000 kilograms, or Part 3 Vehicle Regulations August 26,

14 a tandem drive axle truck tractor in combination with a single axle jeep and lowbed semi-trailer where the sum of the axle loads on the tandem drive axle and the single axle of the jeep exceeds the greater of 24,000 kilograms or the weight allowed under the Table of Maximum Gross vehicle weight for axle Groups under Subsection (ii) of this Part. (e) (f) (g) (h) (i) operate a self-loading truck tractor where the gross axle weight on the steering axle exceeds 9,100 kilograms. No person shall, without an overweight or oversize vehicle permit drive or operate a vehicle where the gross axle weight of any axle of a tandem or tridem axle exceeds 9,100 kilograms, or where the gross axle weight of any 2 adjacent axles of a tridem axle exceeds 17,000 kilograms. operate a bed truck used in oil exploration where the gross axle weight on the steering axle exceeds 9,100 kilograms. No person shall, without a overweight or oversize vehicle permit, drive or operate a truck tractor equipped with a winch behind the cab used in oilfield exploration where the gross weight on the steering axle exceeds 9,100 kilograms. No person shall, without a overweight or oversize vehicle permit, drive or operate a TAC vehicle including a truck tractor equipped with a crane behind the cab, in combination with a semi-trailer, unless the combination conforms with the dimensions and weights as shown in Schedule "I". In the event that the dimensions and weights for the tractor and semi-trailer combinations shown in Schedule "I" are in conflict with other requirements in these regulations, the requirements shown in Schedule "I" prevail Drive axle. No person shall, without an overweight or oversize vehicle permit, drive or operate on a highway: a vehicle or combination of vehicles having a gross weight on the drive axle that is less than 20% of the gross vehicle weight; or a combination of vehicles with a gross vehicle weight in excess of 38,000 kilograms unless the towing vehicle has a tandem drive axle Weight to Horsepower. No person shall, without an overweight or oversize vehicle permit, drive or operate upon a highway a combination of vehicles unless the gross vehicle weight to the manufacturer s rated horsepower of the towing vehicle bears a relationship of not more than 150 kilograms to one horsepower Towing dollies. No person shall drive or operate on a highway a commercial vehicle that is towing a towing dolly where the net weight of the towing dolly plus the gross weight of a motor vehicle, one axle of which is being carried by the towing dolly, exceeds 2,800 kilograms. Part 3 Vehicle Regulations August 26,

15 TAC Lowbed. Notwithstanding the provisions of Subsections (ii) and (ii), a tandem drive axle truck tractor may be coupled to a single axle jeep or a single axle jeep and lowbed semi-trailer provided that the inter-axle spacing between the tandem drive axle and the jeep single axle is not less than 1.2 metres nor more than 3.5 metres TAC Truck Prohibitions This section applies ONLY to drivers or operators of TAC trucks, trucks and pony trailers, trucks and full trailers, C trains with C converter dolly and inter-city buses. operate: (i) (ii) (iv) (v) (vi) (vii) (viii) 3.4 Pilot Cars and Signs a TAC truck unless it conforms to the dimensions and weights as shown in Schedule D of this Bylaw. a TAC truck and pony trailer unless the combination conforms to the dimensions and weights shown in Schedule E of this Bylaw. a TAC truck and full trailer unless the combination conforms to the dimensions and weights shown in Schedule F of this Bylaw. a TAC C train with a C converter dolly unless the combination conforms to the dimensions and weights shown in Schedule G of this Bylaw. a TAC inter-city bus unless it conforms to the dimensions and weights shown in Schedule H of this Bylaw. a TAC tractor with an installed crane and semi-trailer unless it conforms to the dimensions and weights shown on Schedule I of this Bylaw. a truck equipped with 2 steering axles unless: (1) the gross weight of the 2 axles does not exceed 17,000 kilograms, (2) the gross weight of each single axle does not exceed 9,100 kilograms, and (3) the inter-axle spacing does not exceed 1.85 metres, or a truck with a booster axle assembly where the tires of the booster axle are in contact with the ground, unless the truck is a concrete ready mix truck Standards. Where conditions of an overweight or oversize vehicle permit prescribe that pilot cars, signs, flags, or lights be provided by the Permittee, the standards for equipment as set forth in this Bylaw shall be complied with, unless otherwise prescribed by the conditions of the permit Gross Weight. Pilot cars shall be private passenger motor vehicles or commercial vehicles of a licensed gross vehicle weight not exceeding 5,500 kg Signs. Signs required by a permit to be displayed on an oversized vehicle or load shall be as follows: sign panel size, 150 cm by 30 cm; black lettering on yellow background; letters shall be 20 cm in height of 3 cm stroke; Part 3 Vehicle Regulations August 26,

16 shall contain only the words "Wide Load" or in the case of loads only overlength, the words, "Long Load"; Mobile Homes and Modular Buildings. Mobile homes and modular buildings exceeding 3.5 metres in width shall in addition to the requirements in subsection of this part, display on the rear thereof a sign as follows: yellow background with lettering of red reflective materials; letters shall be a minimum of 15 cm in height of a 3 cm stroke; shall contain the words, "CAUTION MAY SLOW OR STOP UNEXPECTEDLY" Pilot Car. Every operator of a pilot car shall ensure that the pilot car is while escorting a vehicle and load, equipped with a roof mounted Long Load, Wide Load, Oversize Load, or D sign that complies with the requirements of the Commercial Transport Act, and while escorting a vehicle or a vehicle and load in excess of 27.5 metres in length and less than 3.2 metres in width or a load in excess of 3.2 metres in width, equipped with a roof mounted Long Load, Wide Load, Oversize Load, or D sign that complies with the requirements of the Commercial Transport Act Flags. Flags on an oversize vehicle or load shall be red in colour, mounted on all four corners or projections of the vehicle or load, of a minimum size of 30 cm square, or be in strips that are not more than 3 cm in width not less than 45 cm in length and that cover an overall width of not less than 15 cm Lighting. If night travel of oversize vehicles or loads is authorized by permit, the extremities of the oversize vehicle or load shall be lighted in a manner not inconsistent with the provisions of Motor Vehicle Act Sign Prohibition. No person shall drive or operate on a highway a motor vehicle or a commercial vehicle displaying a sign indicating the presence of an oversize vehicle or load when, in fact, an oversize vehicle or load is not being transported or escorted Proximity. A pilot car when escorting an oversize vehicle or load on a two lane or three lane highway shall precede the oversize vehicle or load at a distance of not less than 100 metres nor more than 500 metres. When escorting an oversize vehicle or load on a four lane or divided highway, the pilot car shall follow the oversize vehicle or load at a distance of not less than 100 metres nor more than 500 metres. Notwithstanding this provision, a lead pilot car shall, when necessary, precede the oversize vehicle or load through tunnels, structures, etc., at an adequate distance so as to provide ample warning for oncoming vehicles. Part 3 Vehicle Regulations August 26,