Miscellaneous Products

Transcription

1 Category Seals Felsted Control Cables Salami Cable Remote Controls Thread Sealants Allied Witan Filter Vents Denso Petrolatum Tape (Corrosion Protection) Boeshield T-9 Corrosion Shield Anti-Seize Products SCRUBS in-a-bucket Hand Cleaner Towels Conbraco Y Strainers Hub City Splined Billets, Hubs, Reducers Dill Tire Service Products Hose Nozzles Textbooks Boss Gloves Channellock Hand Tools Houston Pneumatic Vibrators Cable (Wire) Ties Hannay Hose Reels Pressure Washer Products Rawson Koenig Hydraulic Worm Gear Winches Kawasaki / Lantec Peel Press Drive Fluids: Hydraulic, Transmission, Gear Lube, Engine Oil CRC Chemical Maintenance Products Lubrication Equipment & Accessories (Alemite, Lumax) Page Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information. 1331

2 Seals Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Category Inch Sizes U-Seals Piston Cups Vee Packing Sets Wear Rings Piston T-Seals Piston Rings Rod T-Seals Wiper Rings Quad Rings Caterpillar D-Rings Piston Seals O-Rings Back-Up Rings Retainer Rings Self Aligning Bearings Metric Sizes Metric U-Seals Assortment Kits & Tools Assortment Kits Cylinder Kits & Parts Cylinder Kits Page Indexes & Technical Information Miscellaneous Products 1332

3 Seals Inch Sizes Homogeneous Buna-N U-Seals Style HRU u-seals are precision molded from 80 Durometer Buna-N rubber. Sizes include those found in Army-Navy spec. AN6226 and narrow cross-section sizes found in JIC cylinders and the popularly termed "Huva Cup". EP suffix signifies Ethylene Propylene. V suffix signifies Fluorocarbon. Material: 80 Durometer Rubber. Temperature Range: -40 F to 250 F. Pressure Range: 0 to 1,000 PSI. Homogeneous Buna-N U-Seals Model Number Cross Sect. I.D. O.D. Ht H C1CY65 HRU /32 1-3/16 1-1/2 5/ Polyurethane U-Seals Molded from tough, abrasion resistant polyurethane. The four lobed expander ring energizes the sealing tips, even at zero pressure, to help prevent "weeping" when the system is idle. Items with N suffix are made from 90 Durometer Nitrile. Items with V suffix are made from Fluorocarbon. Material: Urethane. Temperature Range: -65 F to 220 F. Pressure Range: 0 to 5,000 PSI. Standard Type: Height & cross section are equal. Deep Type: Height is greater than cross section. Type SQB: Height & cross section are equal. Beveled lip design provides superior film breaking. Type B: Height is greater than cross section. Beveled lip design provides superior film breaking. Model Number Polyurethane U-Seals Cross Sect. I.D. O.D. Ht H C1DM70 U B 1/8 3/16 7/16 1/ C1DM72 U SQB 1/8 1/4 1/2 1/ C1DM71 U B 1/8 1/4 1/2 1/ C1DM74 U SQB 1/8 5/16 9/16 1/ C1DM73 U B 1/8 5/16 9/16 1/ C1DM75 U /8 3/8 5/8 1/ C1DM77 U SQB 1/8 1/2 3/4 1/ C1DM76 U B 1/8 1/2 3/4 1/ C1DM78 U /8 5/8 15/16 1/ C1DM80 U SQB 1/8 5/8 7/8 1/ C1DM79 U B 1/8 5/8 7/8 1/ C1DM81 U /8 11/16 15/16 1/ C1DM85 U SQB 1/8 3/4 1 1/ C1DM83 U B 1/8 3/4 1 3/ C1DM84 U B 1/8 3/4 1 1/ C1DM86 U /8 13/16 1-1/16 1/ C1DM88 U SQB 1/8 7/8 1-1/8 1/ C1DM87 U B 1/8 7/8 1-1/8 1/ C1DM91 U SQB 1/ /4 1/ C1DM89 U B 1/ /4 3/ C1DM90 U B 1/ /4 1/ C1DM92 U SQB 1/8 1-1/16 1-5/16 1/ C1DM94 U SQB 1/8 1-1/16 1-3/8 1/ C1DM93 U B 1/8 1-1/16 1-3/8 1/ C1DM95 U /8 1-3/16 1-7/16 1/ C1DM96 U B 1/8 1-3/16 1-7/16 3/ C1DM97 U B 1/8 1-3/16 1-7/16 1/ C1DN11 U SQB 1/8 1-1/4 1-1/2 1/ C1DM98 U B 1/8 1-1/4 1-1/2 3/ C1DM99 U B 1/8 1-1/4 1-1/2 1/ C1DN14 U SQB 1/8 1-3/8 1-5/8 1/ C1DN13 U B 1/8 1-3/8 1-5/8 1/ C1DN16 U SQB 1/8 1-1/2 1-3/4 1/ C1DN15 U B 1/8 1-1/2 1-3/4 1/ C1DN17 U SQB 1/8 1-5/8 1-7/8 1/ C1DN19 U SQB 1/8 1-3/4 2 1/ C1DN20 U / /4 1/ C1DN21 U /8 2-1/4 2-1/2 1/ C1DN24 U /8 2-3/4 3 1/ C1HH21 U /32 1-3/16 1-1/2 5/ C1HH22 U /32 1-1/4 1-9/16 5/ C1HH23 U /32 1-3/8 1-11/16 5/ C1DN26 U /16 1/2 7/8 3/ C1DN27 U SQB 3/16 5/8 1 3/ C1ZX37 U B 3/16 5/8 1 5/ C1DN29 U SQB 3/16 3/4 1-1/8 3/ C1DN28 U B 3/16 3/4 1-1/8 5/ C1DN31 U SQB 3/16 7/8 1-1/4 3/ C1DN30 U B 3/16 7/8 1-1/4 5/ C1DN35 U SQB 3/ /8 3/ C1DN32 U B 3/ /8 1/ C1DN33 U B 3/ /8 5/ C1DN34 U B 3/ /8 3/ Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1333

4 Seals Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Inch Sizes Model Number Polyurethane U-Seals Cross Sect. I.D. O.D. Ht H C1DN37 U SQB 3/16 1-1/16 1-1/2 3/ C1DN36 U B 3/16 1-1/16 1-1/2 1/ C1ER50 U B 3/16 1-1/16 1-1/2 5/ C1DN38 U /16 1-3/16 1-9/16 3/ C1DN42 U SQB 3/16 1-1/4 1-5/8 3/ C1DN39 U B 3/16 1-1/4 1-5/8 1/ C1DN40 U B 3/16 1-1/4 1-5/8 5/ C1DN41 U B 3/16 1-1/4 1-5/8 3/ C1DN46 U SQB 3/16 1-3/8 1-3/4 3/ C1DN43 U B 3/16 1-3/8 1-3/4 1/ C1DN44 U B 3/16 1-3/8 1-3/4 5/ C1DN45 U B 3/16 1-3/8 1-3/4 3/ C1DN50 U SQB 3/16 1-1/2 1-7/8 3/ C1DN47 U B 3/16 1-1/2 1-7/8 1/ C1DN48 U B 3/16 1-1/2 1-7/8 5/ C1DN49 U B 3/16 1-1/2 1-7/8 3/ C1DN51 U /16 1-5/8 2 3/ C1ER51 U SQB 3/16 1-5/8 2 3/ C1DN52 U B 3/16 1-5/8 2 1/ C1DN53 U B 3/16 1-5/8 2 5/ C1DN54 U B 3/16 1-5/8 2 3/ C1DN58 U SQB 3/16 1-3/4 2-1/8 3/ C1DN55 U B 3/16 1-3/4 2-1/8 1/ C1DN56 U B 3/16 1-3/4 2-1/8 5/ C1DN57 U B 3/16 1-3/4 2-1/8 3/ C1DN60 U SQB 3/16 1-7/8 2-1/4 3/ C1DN59 U B 3/16 1-7/8 2-1/4 3/ C1DN63 U SQB 3/ /8 3/ C1DN61 U B 3/ /8 5/ C1DN62 U B 3/ /8 3/ C1DN65 U SQB 3/16 2-1/8 2-1/2 3/ C1DN64 U B 3/16 2-1/8 2-1/2 1/ C1DN68 U SQB 3/16 2-1/4 2-5/8 3/ C1DN67 U B 3/16 2-1/4 2-5/8 3/ C1DN69 U SQB 3/16 2-3/8 2-3/4 3/ C1DN73 U SQB 3/16 2-1/2 2-7/8 3/ C1DN70 U B 3/16 2-1/2 2-7/8 1/ C1DN71 U B 3/16 2-1/2 2-7/8 5/ C1DN72 U B 3/16 2-1/2 2-7/8 3/ C1DN75 U SQB 3/16 2-5/8 3 3/ C1DN74 U B 3/16 2-5/8 3 3/ C1DN77 U SQB 3/16 2-3/4 3-1/8 3/ C1DN76 U B 3/16 2-3/4 3-1/8 3/ C1DN78 U /16 2-7/8 3-1/4 3/ C1DN79 U / /8 3/ C1DN80 U B 3/ /8 3/ C1DN82 U SQB 3/16 3-1/8 3-1/2 3/ C1DN81 U B 3/16 3-1/8 3-1/2 3/ C1DN86 U B 3/16 3-1/2 3-7/8 3/ C1DN89 U SQB 3/16 3-5/8 4 3/ C1DN88 U B 3/16 3-5/8 4 3/ C1DN92 U B 3/ /8 3/ C1DN94 U /4 3/4 1-1/4 1/ Polyurethane U-Seals Cross Sect. Model I.D. O.D. Ht H Number C1DN96 U /4 13/16 1-7/16 1/ C1DN98 U SQB 1/ /2 1/ C1DN97 U B 1/ /2 3/ C1DN99 U /4 1-1/16 1-5/8 1/ C1DP11 U B 1/4 1-1/16 1-5/8 3/ C1DP12 U /4 1-3/ /16 1/ C1DP14 U SQB 1/4 1-1/4 1-3/4 1/ C1DP13 U B 1/4 1-1/4 1-3/4 3/ C1DP15 U /4 1-3/8 1-7/8 1/ C1DP16 U B 1/4 1-3/8 1-7/8 3/ C1DP19 U SQB 1/4 1-1/2 2 1/ C1DP17 U B 1/4 1-1/2 2 5/ C1DP18 U B 1/4 1-1/2 2 3/ C1DP22 U /4 1-3/4 2-1/4 1/ C1DP23 U B 1/4 1-3/4 2-1/4 3/ C1DP25 U B 1/4 1-7/8 2-3/8 3/ C1DP28 U SQB 1/ /2 1/ C1DP26 U B 1/ /2 5/ C1DP27 U B 1/ /2 3/ C1DP30 U B 1/4 2-1/8 2-5/8 3/ C1DP31 U /4 2-1/4 2-3/4 1/ C1DP32 U B 1/4 2-1/4 2-3/4 3/ C1DP34 U B 1/4 2-3/8 2-7/8 3/ C1DP37 U SQB 1/4 2-1/2 3 1/ C1DP35 U B 1/4 2-1/2 3 3/ C1DP39 U B 1/4 2-5/8 3-1/8 3/ C1DP41 U SQB 1/4 2-3/4 3-1/4 1/ C1DP40 U B 1/4 2-3/4 3-1/4 3/ C1DP42 U / /2 1/ C1DP43 U B 1/ /2 3/ C1DP46 U B 1/4 3-1/4 3-3/4 3/ C1DP50 U SQB 1/4 3-1/2 4 1/ C1DP48 U /4 3-1/2 4 1/ C1DP49 U B 1/4 3-1/2 4 3/ C1DP52 U SQB 1/4 3-3/4 4-1/4 1/ C1KN66 U B 1/4 3-3/4 4-1/4 3/ C1DP56 U SQB 1/ /2 1/ C1DP53 U B 1/ /2 3/ C1DP54 U D 1/ /2 1/ C1DP55 U B 1/ /2 9/ C1DP60 U /4 4-1/2 5 1/ C1DP61 U B 1/4 4-1/2 5 3/ C1DP63 U B 1/4 4-1/2 5 9/ C1DP64 U B 1/4 4-1/2 5 5/ C1DP68 U / /2 1/ C1DP69 U B 1/ /2 3/ C1DP73 U /4 5-1/2 6 1/ C1DP74 U B 1/4 5-1/2 6 3/ C1DP75 U B 1/4 5-1/2 6 9/ C1DP85 U B 5/ /8 1/ C1DP87 U /16 1-1/4 1-7/8 5/ C1DP88 U B 5/16 1-1/4 1-7/8 3/ C1DP91 U SQB 5/16 1-3/8 2 5/

5 Seals Inch Sizes Model Number Polyurethane U-Seals Cross Sect. I.D. O.D. Ht H C1DP90 U B 5/16 1-3/8 2 3/ C1DP92 U /16 1-1/2 2-1/8 5/ C1DP97 U B 5/16 1-3/4 2-3/8 3/ C1DP98 U /16 1-7/8 2-1/2 5/ C1DP99 U / /8 5/ C1DQ11 U B 5/ /8 1/ C1DQ14 U B 5/16 2-1/4 2-7/8 1/ C1DQ15 U /16 2-3/8 3 5/ C1DQ16 U /16 2-1/2 3-1/8 5/ C1DQ17 U B 5/16 2-1/2 3-1/8 1/ C1DQ19 U /16 2-3/4 3-3/8 5/ C1DQ20 U B 5/16 2-3/4 3-3/8 1/ C1DQ21 U /16 2-7/8 3-1/2 5/ C1DQ24 U B 5/ /8 1/ C1DQ26 U B 5/16 3-3/8 4 1/ C1DQ32 U / /8 5/ C1GK82 U B 5/ /8 9/ C1ER52 U /16 4-3/8 5 5/ C1DQ35 U /16 4-1/2 5-1/8 5/ C1DQ40 U /8 1-1/4 2 3/ C1DQ45 U /8 1-3/4 2-1/2 3/ C1DQ51 U B 3/8 2-1/2 3-1/4 1/ C1DQ54 U /8 2-3/4 3-1/2 3/ C1DQ56 U SQB 3/ /4 3/ C1DQ58 U B 3/8 3-1/4 4 1/ C1DQ60 U /8 3-1/2 4-1/4 3/ C1DQ64 U D 3/8 3-3/4 4-1/2 1/ C1DQ66 U B 3/ /4 5/ C1DQ69 U SQB 3/8 4-1/4 5 3/ C1DQ67 U D 3/8 4-1/4 5 1/ C1DQ68 U B 3/8 4-1/4 5 5/ C1DQ70 U B 3/8 4-1/2 5-1/4 5/ C1EV13 U B 3/ /4 5/ C1DQ77 U /8 5-1/4 6 3/ C1DQ78 U D 3/8 5-1/4 6 1/ C1DQ80 U D 3/8 6-1/4 7 1/ C1DQ81 U SQB 1/ / C1DQ82 U /2 2-1/2 3-1/2 1/ Cotton Fabric & Rubber Piston Cups Material: Cotton fabric & rubber. Temperature Range: -65 to 220 F. Pressure Range: 0 to 3000 PSI. Note: Hole is punched if hole size listed in table. Cotton Fabric & Rubber Piston Cups Model Number Bore Dia. Lip Ht Thick Hole Size C1CB F 1-1/4 7/16 3/ C1CB F 1-1/2 1/2 1/ C1CB F 2 1/2 1/ C1CC F 2-1/2 1/2 1/ C1CC F 3 5/8 5/ C1CC F 4 5/8 5/ Vee Packing Sets All sets include fabric reinforced rubber vee cups. When feasible, one or two urethane vee rings are included to improve low pressure sealing. Most sets use nylon adaptors. Material: Fabric reinforced rubber & urethane vee rings, nylon top and bottom adaptors. Temperature Range: -65 F to 220 F. Pressure Range: 0 to 3000 PSI (4 Vees). 0 to 5000 PSI (5 Vees). 0 to 10,000 PSI (6 Vees). Construction Code: 1st number in Code is quantity of Top nylon adaptors (usually 1). 2nd number is quantity of Urethane vee rings. 3rd number is quantity of Fabric vee rings. 4th number is quantity of Bottom nylon adaptors (usually 1). Model Number Vee Packing Sets Code TUFB I.D. O.D. Ht C1DR63 VS06204X /8 1-1/ C1DR64 VS07504X /4 1-1/ C1DR66 VS08104X /16 1-5/16 7/ C1DR68 VS08704X /8 1-3/ C1DR69 VS10003X /8 61/ C1DR70 VS10004X / C1DR71 VS10005X /8 1-1/ C1DR72 VS11204X /8 1-5/8 7/ C1DR74 VS12504X /4 1-3/4 13/ C1DR77 VS15004X /2 2 13/ C1DR78 VS15004X / C1DR79 VS15004X / / Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1335

6 Seals Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Inch Sizes C1DR83 VS16205X /8 2-1/4 1-1/ C1DR84 VS17504X /4 2-1/ C1DR85 VS17505X /4 2-3/8 1-1/ C1DR87 VS20004X /2 7/ C1DR88 VS20004X / C1DR89 VS20004X /2 1-1/ C1DR90 VS20005X /8 1-1/ C1DR91 VS20006X /4 1-3/ C1DR94 VS22504X /4 2-3/4 13/ C1DR95 VS22504X /4 2-3/ C1DR96 VS22505X /4 2-7/8 1-1/ C1DR97 VS22506X / C1DS12 VS25004X /2 3 13/ C1DS16 VS27506X /4 3-1/2 1-3/ C1DS17 VS30004X /2 7/ C1DS19 VS32506X / / C1DS20 VS32506X / / C1DS21 VS35004X /2 4 3/ C1DS22 VS35004X / C1DS24 VS37504X /4 4-1/ C1DS25 VS37506X /4 4-1/2 1-3/ C1DS27 VS40004X / C1DS28 VS40004X /2 1-1/ C1DS31 VS45004X / C1DS34 VS47506X /4 5-1/2 1-3/ C1DS36 VS50004X /2 1-1/ C1DS40 VS60004X / C1DS42 VS70004X / Nylon Wear Rings Made of glass reinforced nylon with physical properties equivalent to bronze. Highly recommended due to low wear rate, non-scoring properties and ability to ingest metal chips. SC suffix designates a scarf cut design. ST suffix designates a step cut design. Temperature Range: -40 F to 250 F. Tensile Strength: 27,000 PSI. Compressive Strength: 35,000 PSI. Model Number Model Number Vee Packing Sets Code TUFB I.D. Nylon Wear Rings Thickness O.D. Width Ht O.D. C1BW /8 1/ C1FW /8 1/2 2-1/ C1BW /8 1/2 2-1/ Nylon Wear Rings Model Thickness Width O.D. Number C1KK /8 1/2 2-3/ C1BW /8 1/ C1BW /8 1/2 3-1/ C1FE /8 1/2 3-3/ C1BW /8 1/ C1BW /8 1/2 4-1/ C1GH /8 1/ C1KK /8 1/2 5-1/ C1BW /8 1/ C1KK /8 1/ C1BW /8 5/ C1BW /8 3/ C1BW /8 3/8 2-1/ C1BW /8 5/8 2-1/ C1BW /8 3/ C1BW /8 3/8 3-1/ C1BW /8 3/ C1BW /8 5/ C1BW /8 3/ C1BW /8 5/ C1BW /8 3/ C1BW /8 3/4 2-1/ C1BW /8 3/ C1BW /8 3/4 3-1/ C1GM /8 3/ C1BW /8 3/4 4-1/ C1GM /8 3/ C1KK / / C1KK / C1BW / Piston T-Seals T-Seals combine a resilient sealing ring with a hard, split back-up ring on each side of the sealing element. The assembly installs in a groove comparable to size required for an o-ring. T-Seals are non-spiraling and extrusion resistant to 10,000 PSI. Material: Hard plastic back-up rings. Buna-N rubber seal. Temperature Range: -65 F to 220 F. Pressure Range: 0 to 10,000 PSI. 1336

7 Seals Inch Sizes Model Number Piston T-Seals Bore Dia. O-Ring Groove Dash No. C1DM26 TP / C1DM28 TP C1DM29 TP / C1DM30 TP / C1DM32 TP / C1DM33 TP C1DM34 TP / C1DM36 TP C1DM38 TP C1DM39 TP / C1DM40 TP Cast Iron Piston Rings Material: Cast Iron. When using cast iron piston rings, it is crucial to use the correct groove design for proper performance of the cylinder. Please use the following guidelines when cutting a cast iron piston ring groove. Groove Width: To permit the ring to slide freely into the groove, the groove must be at least inches wider than the maximum piston ring width with a tolerance of /-0 inches. Groove Depth: Grooves must be at least inches deeper than the maximum radial wall thickness of the piston ring with a tolerance of /-0 inches. This is to avoid any possibility of the ring bottoming in the groove when the ring is compressed to its working diameter. Radial Clearance: The radial clearance between the cylinder bore and piston should be less than 1/3 of the radial wall thickness of the piston ring to ensure sealing effectiveness. Model Number Cast Iron Piston Rings O.D. C1DK99 SPR C1DL12 SPR C1GG42 SPR Rod T-Seals Width Wall Thickness 0.127/ / / T-Seals combine a resilient sealing ring with a hard, split back-up ring on each side of the sealing element. The assembly installs in a groove comparable to size required for an o-ring. T-Seals are non-spiraling and extrusion resistant to 10,000 PSI. Material: Hard plastic back-up rings. Buna-N rubber seal. Temperature Range: -65 F to 220 F. Pressure Range: 0 to 10,000 PSI. Model Number Rod T-Seals Rod Dia. O-Ring Groove Dash No. C1DM44 TR-008 5/ C1DM52 TR C1FD17 TR / C1DM55 TR / Urethane Wiper Rings Style AN Material: Urethane. Temperature Range: -65 F to 220 F. Note: SH suffix designates slotted heel design. V suffix designates fluorocarbon material. B suffix designates carboxilated nitrile material. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1337

8 Seals Inch Sizes Hydraulic Power & Control Urethane Wiper Rings Style AN Model Number Rod Dia. A Groove O.D. B Groove Width C C1CH86 AN C1CH87 AN C1CH88 AN C1CH89 AN C1CH91 AN Metal Clad Rubber Wiper Rings Miscellaneous Products Fluid Conveying Pneumatic Power & Control C1CH92 AN C1CH93 AN C1CH95 AN C1CH96 AN C1CH97 AN C1CH98 AN C1CH99 AN C1CJ11 AN C1CJ12 AN C1CJ13 AN C1CJ14 AN C1CJ15 AN C1CJ16 AN C1CJ17 AN C1CJ18 AN C1CJ19 AN C1CJ20 AN C1CJ23 AN C1CJ24 AN C1CJ26 AN C1CJ27 AN C1CJ28 AN C1CJ30 AN C1CJ32 AN C1CJ33 AN Urethane Wiper Rings Style BT Material: Rubber. Temperature Range: -40 F to 240 F. Metal Clad Rubber Wiper Rings Model Number Rod Dia. A Wiper O.D. B Ht C C1DD80 MCN /4 1/ C1DD81 MCN /8 3/ C1DD82 MCN /2 3/ C1DD84 MCN /4 1-11/16 3/ C1DD85 MCN /4 1-3/4 1/ C1DD86 MCN /8 1-3/4 3/ C1DD87 MCN /2 1-7/8 1/ C1DD88 MCN /2 1-7/8 3/ C1DD89 MCN /2 2 1/ C1DD90 MCN /4 2-1/8 3/ C1DD91 MCN /4 2-1/4 1/ C1DD92 MCN /4 2-3/8 1/ C1DD94 MCN /8 3/ C1DD95 MCN /8 1/ C1DD96 MCN /2 1/ C1DD97 MCN /4 2-3/4 1/ C1DD99 MCN /2 3 1/ C1DE12 MCN /2 1/ Metal Clad Urethane Wiper Rings Indexes & Technical Information Material: Urethane. Temperature Range: -65 F to 220 F. Urethane Wiper Rings Style BT Model Number Rod Dia. A Wiper O.D. B Base Thickness C C1CL80 BT /8 3/ C1CL83 BT /2 1-7/8 3/ C1CL85 BT /8 3/ A Durometer urethane lip securely bonded to sturdy metal case. Non-abrasive and highly effective in removing dirt and contaminants from the rod. Material: Urethane. Temperature Range: -65 F to 220 F. Metal Clad Urethane Wiper Rings Model Number Rod Dia. A Wiper O.D. B Ht C C1DE14 MCU-0750-G 3/4 1-1/4 5/ C1DE15 MCU-0875-G 7/8 1-3/8 5/

9 Seals Inch Sizes C1DE16 MCU-1000-G 1 1-1/2 5/ C1DE17 MCU-1120-G 1-1/8 1-5/8 5/ C1DE18 MCU-1187-G 1-3/16 1-5/8 1/ C1DE20 MCU-1375-G 1-3/8 1-7/8 5/ C1DE34 MCU-2006-G /16 3/ C1DE37 MCU-2252-G 2-1/4 3 1/ C1DE39 MCU-2376-G 2-3/8 3-1/8 3/ C1DE44 MCU-2503-G 2-1/2 3 3/ C1DE57 MCU-3506-G 3-1/2 4-1/8 5/ Heavy Duty Metal Clad Urethane Wiper Rings Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in Heavy-Duty U-Seals. Built for severe service, these wipers are capable of surviving hostile environments. Material: Urethane. Temperature Range: -65 F to 220 F. Heavy Duty Metal Clad Urethane Wiper Rings Metal Clad Urethane Wiper Rings Model Number Model Number Rod Dia. A Rod Dia. A Wiper O.D. B Ht C Wiper O.D. B Ht C C1KM74 MCU-0625-D 5/8 1-1/8 5/ C1KM75 MCU-1500-D 1-1/2 2 1/ C1GK26 MCU-1751-D 1-3/4 2-1/4 1/ C1KG30 MCU-2000-D 2 2-1/2 5/ C1KH35 MCU-2500-D 2-1/2 3 5/ C1GK27 MCU-2750-D 2-3/4 3-1/4 5/ C1KM76 MCU-3000-D 3 3-1/2 5/ Urethane Wiper Rings Style ST Precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. V suffix designates fluorocarbon construction. Material: Urethane or Fluorocarbon (if V suffix). Temperature Range: Urethane -65 F to 220 F. Fluorocarbon -20 F to 400 F. Urethane Wiper Rings Style ST Model Number Rod Dia. A Wiper O.D. B Base Thickness C C1DL53 ST-50 1/2 3/4 1/ C1DL54 ST-62 5/8 7/8 1/ C1DL55 ST-75 3/4 1-1/8 3/ C1DL56 ST-87 7/8 1-1/4 3/ C1DL24 ST /8 3/ C1DL25 ST /8 1-1/2 3/ C1DL26 ST /16 1-9/16 3/ C1DL27 ST /4 1-5/8 3/ C1DL28 ST /8 1-3/4 3/ C1DL30 ST /2 1-7/8 3/ C1DL31 ST /8 2 3/ C1DL32 ST /4 2-1/8 3/ C1DL33 ST /8 2-1/4 3/ C1DL35 ST /2 1/ C1DL36 ST /8 2-5/8 1/ C1DL37 ST /4 2-3/4 1/ C1DL40 ST /2 3 1/ C1DL41 ST /4 3-1/4 1/ C1DL43 ST /2 1/ C1DL44 ST /4 3-3/4 1/ C1DL46 ST /2 4 1/ C1DL48 ST /4 4-1/4 1/ C1DL49 ST /2 1/ C1DL51 ST /2 5-1/4 3/ C1DL52 ST /4 5-1/2 3/ Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1339

10 Seals Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Inch Sizes Urethane Wiper Rings Style KW Material: Urethane. Temperature Range: -65 F to 220 F. Urethane Wiper Rings Style KW Model Number Rod Dia. A Wiper O.D. B Base Thickness C C1DC94 KW /4 1-1/ C1DC95 KW /8 1-1/ C1DC96 KW / C1DC98 KW /4 1-5/ C1DC99 KW /8 1-3/ C1DD11 KW /2 1-7/ C1DD13 KW /4 2-1/ C1DD14 KW / C1DD16 KW / Buna-N Quattro Rings Style QR The four lobed design of these seals provide twice the sealing surface of ordinary o-rings. They can be used in a variety of static and dynamic sealing applications including rotary, reciprocating or oscillating motion. Material: Buna-N. Temperature Range: -40 F to 240 F. Pressure Range: Varies according to diametral clearance. Buna-N Quattro Rings Style QR Model Number Dash Size Pkg. Qty C1FC63 QR C1FC68 QR C1FC69 QR C1FC74 QR C1FC77 QR C1FC78 QR C1FC79 QR C1FC80 QR C1FC81 QR C1FC82 QR C1FC83 QR C1FC84 QR C1FC89 QR Buna-N Quattro Rings Style QR Model Number Dash Size Pkg. Qty C1FC90 QR C1FC91 QR C1FC92 QR C1FC93 QR C1FC94 QR C1FC95 QR C1FC96 QR C1FC97 QR C1FC98 QR Caterpillar D-Rings Note: Caterpillar part numbers are used as a reference only. It is not implied that these parts are original replacement parts. Caterpillar D-Rings Model Number I.D. (mm) C1EW59 CTC-1P C1EW60 CTC-1P C1EW61 CTC-1P C1EW62 CTC-1P

11 Seals Inch Sizes Glass Filled PTFE Piston Seals Style 1400 Glass filled PTFE for low breakaway and low running friction. Popular choice of many cylinder manufacturers. Rubber energizer under seal assures positive contact with the dynamic surfaces. Piston diameter F dimensions are given for pistons without wear rings. Material: 15% glass filled PTFE seal with rubber energizer. Temperature Range: -40 F to 220 F. Pressure Range: 0 to 5,000 PSI. Glass Filled PTFE Piston Seals Style 1400 Seal Height B & Model Number Bore Dia. A ±0.002 Cross Section C Groove Width D ±0.002 Groove Dia. E ±0.002 Piston Dia. F ±0.001 C1DH42 PS ± C1DH43 PS ± C1DH44 PS ± C1DH45 PS ± C1DH47 PS ± C1DH48 PS ± C1DH49 PS ± C1DH50 PS ± C1DH51 PS ± C1DH52 PS ± C1DH53 PS ± C1DH54 PS ± C1DH56 PS ± C1DH57 PS ± C1DH60 PS ± Glass Filled PTFE Piston Seals Style 1600 Model Number Material: 15% glass filled PTFE seal. Rubber energizer. Temperature Range: -40 F to 220 F. Pressure Range: 0 to 5,000 PSI. Note: Piston diameter F dimensions are given for pistons without wear rings. Bore Dia. A ±0.001 Glass Filled PTFE Piston Seals Style 1600 Seal Height B Seal Cross Section C Groove Width D Groove Dia. E C1DH63 PS C1DH64 PS C1DH65 PS Piston Dia. F / / / Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1341

12 Seals Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Inch Sizes Model Number Bore Dia. A ±0.001 Glass Filled PTFE Piston Seals Style 1600 Seal Height B Seal Cross Section C C1DH66 PS C1DH67 PS C1DH68 PS C1DH69 PS C1DH70 PS C1DH71 PS Glass Filled PTFE Piston Seals Style 1800 Groove Width D Groove Dia. E Piston Dia. F / / / / / / Material: 15% glass filled PTFE seal. Rubber energizer. Temperature Range: -40 F to 220 F. Pressure Range: 0 to 5,000 PSI. Note: Piston diameter F dimensions are given for pistons without wear rings Miscellaneous Products Model Number Bore Dia. A ±0.002 Glass Filled PTFE Piston Seals Style 1800 Seal Height B Seal Cross Section C Groove Width D ±0.002 Groove Dia. E ±0.004 C1DH73 PS C1DH74 PS C1DH75 PS C1DH76 PS Piston Dia. F / / / / C1DH77 PS / Indexes & Technical Information C1DH78 PS C1DH80 PS C1DH81 PS C1DH82 PS C1DH83 PS C1DH84 PS / / / / / /

13 Seals Inch Sizes C1DH86 PS C1DH87 PS Bronze Filled PTFE Piston Seals Style 1850 Model Number Bore Dia. A / / Material: Bronze filled PTFE Seal. Rubber Energizer. Temperature Range: -40 F to +220 F Pressure Range: 0 to 5000 PSI Note: Piston diameter "F" dimensions are given for pistons without wear. Interchangeable with the PS1800 style piston seal. Bronze Filled PTFE Piston Seals Style 1850 Seal Height B Seal Cross Section C Groove Width D ±0.002 Groove Dia. E ±0.002 C1KM93 PS C1KM94 PS Polyurethane Piston Seals Style 2700 Model Number Model Number Bore Dia. A ±0.002 Bore Dia. A ±0.002 Glass Filled PTFE Piston Seals Style 1800 Seal Height B Piston Dia. F / / Molded from high grade poly-esters, 5% glass fiber and 5% PTFE. Interchangeable with PS1800 seals. Low friction. High resistance to abrasion & extrusion. The polyurethane material has a high degree of memory and will stretch over a piston and snap into the groove and be ready for immediate assembly. Damage during assembly is virtually eliminated. Piston diameter F dimensions are given for pistons without wear rings. Material: Glass/PTFE filled polyurethane seal. Rubber energizer. Temperature Range: -40 F to 220 F. Pressure Range: 0 to 5,000 PSI. Polyurethane Piston Seals Style 2700 Seal Height B Seal Cross Section C Seal Cross Section C Groove Width D ±0.002 Groove Width D ±0.002 Groove Dia. E ±0.004 Groove Dia. E ±0.004 C1DH92 PS C1DH96 PS C1DH98 PS Piston Dia. F Piston Dia. F / / / Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1343

14 Seals Inch Sizes Hydraulic Power & Control Model Number Bore Dia. A ±0.002 Polyurethane Piston Seals Style 2700 Seal Height B Seal Cross Section C Groove Width D ±0.002 Groove Dia. E ±0.004 C1DJ11 PS C1DJ12 PS C1DJ15 PS Piston Dia. F / / / C1DH89 PS / Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Double-Acting Piston Seals Style PSC Model Number Bore Dia. Seal Height This seal is a double-acting piston seal designed to replace o-rings, quad-rings and T-seals with the same groove dimensions (o-ring dash number). Style 575 urethane back-up rings may be added to either or both sides of the PSC to accommodate wider groove widths. The PSC is made of 95A durometer polyurethane, giving it high extrusion and abrasion resistance. The crowned sealing surface produces a positive seal from vacuum to high pressure. Material: 95A polyurethane seal, 70A nitrile energizer. Temperature Range: -65 F to 220 F. Pressure Range: 0 to 5,000 PSI. Note: Piston diameter F dimensions are given for pistons without wear rings. Double-Acting Piston Seals Style PSC Groove Width Groove Dia. Piston Dia. C1KM95 PSC / / / / C1KM96 PSC-218-WB / / / / C1GG32 PSC / / / / C1GG33 PSC-326-WB / / / / C1GG34 PSC / / / / C1KM97 PSC / / / / C1GG35 PSC-334-WB / / / / C1GG36 PSC / / / / C1GG37 PSC / / / / C1KM98 PSC-342-WB / / / / C1KM99 PSC / / / / C1GG38 PSC-433-WB / / / /

15 Seals Inch Sizes Bronze Filled Piston Seals Style PSQ Model Number Bore Dia. Seal Height These piston seals provide bi-directional, low friction sealing with increased stability and superior leakage control. The square cut energizer provides low pressure sealing and eliminates backside leakage. This seal also effectively seals between different fluids on each side of the piston seal, making gas/liquid sealing combinations possible. Material: 40% bronze filled PTFE seal, rubber energizer and quattro ring. Temperature Range: -40 F to 220 F. Pressure Range: 0 to 5,000 PSI. Note: Piston diameter F dimensions are given for pistons without wear rings. Bronze Filled Piston Seals Style PSQ Groove Width Groove Dia. Piston Dia. C1GM40 PSQ / / C1GN12 PSQ / / C1GN14 PSQ / / C1GN15 PSQ / / C1KN11 PSQ / / Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1345

16 Seals Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Inch Sizes O-Rings 70 Durometer Buna-N O-Rings Material: 70 Durometer Buna-N. Temperature Range: -40 F. to 240 F. Model Number Dash Size Nominal I.D. 70 Durometer Buna-N O-Rings Nominal O.D. Nominal Width Actual I.D. Actual O.D. Actual Width C1CC95 A /16 3/16 1/ C1CC97 A /32 7/32 1/ C1CC98 A /8 1/4 1/ C1CC99 A /32 9/32 1/ C1CD11 A /16 5/16 1/ C1CD12 A /32 11/32 1/ C1CD13 A /4 3/8 1/ C1CD14 A /16 7/16 1/ C1CD15 A /8 1/2 1/ C1CD16 A /16 9/16 1/ C1CD17 A /2 5/8 1/ C1CD19 A /16 11/16 1/ C1CD20 A /8 3/4 1/ C1CD21 A /16 13/16 1/ C1CD22 A /4 7/8 1/ C1CD23 A /16 15/16 1/ C1CD24 A /8 1 1/ C1CD25 A /16 1-1/16 1/ C1CD26 A /8 1/ C1CD27 A /16 1-3/16 1/ C1CD29 A /8 1-1/4 1/ C1CD30 A /16 1-5/16 1/ C1CD31 A /4 1-3/8 1/ C1CD32 A /16 1-7/16 1/ C1CD33 A /8 1-1/2 1/ C1CD35 A /2 1-5/8 1/ C1CD36 A /8 1-3/4 1/ C1CD37 A /4 1-7/8 1/ C1CD38 A /8 2 1/ C1CD39 A /8 1/ C1CD40 A /8 2-1/4 1/ C1CD41 A /4 2-3/8 1/ C1CD42 A /8 2-1/2 1/ C1CD43 A /2 2-5/8 1/ C1CD44 A /8 2-3/4 1/ C1CD45 A /4 2-7/8 1/ C1CD46 A /8 3 1/ C1CD47 A /8 1/ C1CD48 A /4 3-3/8 1/ C1CD49 A /2 3-5/8 1/ C1CD50 A /4 3-7/8 1/ C1CD51 A /8 1/ C1CD54 A /4 4-7/8 1/ Pkg. Qty. 1346

17 Seals Inch Sizes O-Rings Model Number Dash Size Nominal I.D. 70 Durometer Buna-N O-Rings Nominal O.D. Nominal Width Actual I.D. Actual O.D. Actual Width C1CD55 A /8 1/ C1CD61 A /16 3/8 3/ C1CD62 A /32 13/32 3/ C1CD63 A /4 7/16 3/ C1CD64 A /16 1/2 3/ C1CD65 A-110-ORING /8 9/16 3/ C1CD66 A /16 5/8 3/ C1CD67 A /2 11/16 3/ C1CD68 A /16 3/4 3/ C1CD69 A /8 13/16 3/ C1CD70 A /16 7/8 3/ C1CD71 A /4 15/16 3/ C1CD72 A /16 1 3/ C1CD73 A /8 1-1/16 3/ C1CD74 A /16 1-1/8 3/ C1CD76 A /16 3/ C1CD77 A /16 1-1/4 3/ C1CD78 A /8 1-5/16 3/ C1CD79 A /16 1-3/8 3/ C1CD80 A /4 1-7/16 3/ C1CD81 A /16 1-1/2 3/ C1CD82 A /8 1-9/16 3/ C1CD83 A /16 1-5/8 3/ C1CD84 A /2 1-11/16 3/ C1CD85 A-129-ORING /16 1-3/4 3/ C1CD87 A /8 1-13/16 3/ C1CD88 A-131-ORING /16 1-7/8 3/ C1CD89 A-132-ORING /4 1-15/16 3/ C1CD90 A /16 2 3/ C1CD91 A /8 2-1/16 3/ C1CD92 A /16 2-1/8 3/ C1CD93 A /16 3/ C1CD94 A /16 2-1/4 3/ C1CD95 A /8 2-5/16 3/ C1CD96 A /16 2-3/8 3/ C1CD97 A /4 2-7/16 3/ C1CD98 A-141-ORING /16 2-1/2 3/ C1CD99 A /8 2-9/16 3/ C1CE11 A /16 2-5/8 3/ C1CE12 A /2 2-11/16 3/ C1CE13 A /16 2-3/4 3/ C1CE14 A /8 2-13/16 3/ C1CE15 A /16 2-7/8 3/ C1CE16 A /4 2-15/16 3/ C1CE17 A /16 3 3/ C1CE18 A /8 3-1/16 3/ C1CE19 A /16 3/ C1CE20 A /4 3-7/16 3/ C1CE21 A /2 3-11/16 3/ Pkg. Qty. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1347

18 Seals Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Inch Sizes O-Rings Model Number Dash Size Nominal I.D. 70 Durometer Buna-N O-Rings Nominal O.D. Nominal Width Actual I.D. Actual O.D. Actual Width C1CE22 A /4 3-15/16 3/ C1CE23 A /16 3/ C1CE24 A /4 4-7/16 3/ C1CE25 A /2 4-11/16 3/ C1CE27 A /4 4-15/16 3/ C1CE28 A /16 3/ C1CE29 A /4 5-7/16 3/ C1CE30 A /2 5-11/16 3/ C1CE32 A /16 3/ C1CE33 A /4 6-7/16 3/ C1CE38 A /2 7-11/16 3/ C1CE39 A /4 7-15/16 3/ C1CE41 A /4 8-7/16 3/ C1CE49 A /4 1/2 1/ C1CE50 A /16 9/16 1/ C1CE51 A /8 5/8 1/ C1CE52 A /16 11/16 1/ C1CE53 A /2 3/4 1/ C1CE54 A /16 13/16 1/ C1CE55 A /8 7/8 1/ C1CE56 A /16 15/16 1/ C1CE58 A-210-ORING /4 1 1/ C1CE59 A /16 1-1/16 1/ C1CE60 A /8 1-1/8 1/ C1CE61 A /16 1-3/16 1/ C1CE62 A /4 1/ C1CE64 A /16 1-5/16 1/ C1CE65 A /8 1-3/8 1/ C1CE66 A /16 1-7/16 1/ C1CE67 A /4 1-1/2 1/ C1CE68 A /16 1-9/16 1/ C1CE70 A /8 1-5/8 1/ C1CE71 A / /16 1/ C1CE72 A /2 1-3/4 1/ C1CE74 A /8 1-7/8 1/ C1CE75 A /4 2 1/ C1CE76 A /8 2-1/8 1/ C1CE78 A /4 1/ C1CE79 A /8 2-3/8 1/ C1CE80 A /4 2-1/2 1/ C1CE81 A /8 2-5/8 1/ C1CE82 A /2 2-3/4 1/ C1CE83 A /8 2-7/8 1/ C1CE84 A /4 3 1/ C1CE86 A /8 3-1/8 1/ C1CE87 A /4 1/ C1KL23 A-234-VITON /4 1/ C1CE88 A /8 3-3/8 1/ C1CE89 A /4 3-1/2 1/ Pkg. Qty. 1348

19 Seals Inch Sizes O-Rings Model Number Dash Size Nominal I.D. 70 Durometer Buna-N O-Rings Nominal O.D. Nominal Width Actual I.D. Actual O.D. Actual Width C1CE90 A /8 3-5/8 1/ C1CE91 A-238-ORING /2 3-3/4 1/ C1CE92 A-239-ORING /8 3-7/8 1/ C1CE93 A-240-ORING /4 4 1/ C1CE95 A-241-ORING /8 4-1/8 1/ C1CE96 A-242-ORING /4 1/ C1CE97 A /8 4-3/8 1/ C1CE98 A /4 4-1/2 1/ C1CE99 A /8 4-5/8 1/ C1CF11 A /2 4-3/4 1/ C1CF12 A /8 4-7/8 1/ C1CF13 A /4 5 1/ C1CF14 A /8 5-1/8 1/ C1CF15 A /4 1/ C1CF16 A /8 5-3/8 1/ C1CF17 A /4 5-1/2 1/ C1CF18 A /8 5-5/8 1/ C1CF19 A /2 5-3/4 1/ C1CF20 A /8 5-7/8 1/ C1CF21 A /4 6 1/ C1CF22 A /8 6-1/8 1/ C1CF23 A-258-ORING /4 1/ C1CF24 A /4 6-1/2 1/ C1CF25 A /2 6-3/4 1/ C1CF26 A /4 7 1/ C1CF27 A /4 1/ C1CF28 A /4 7-1/2 1/ C1CF29 A /2 7-3/4 1/ C1CF30 A /4 8 1/ C1CF31 A /4 1/ C1CF32 A /4 8-1/2 1/ C1CF33 A /2 8-3/4 1/ C1CF34 A /4 9 1/ C1CF39 A /4 1/ C1CF40 A /2 10-3/4 1/ C1CF41 A /4 1/ C1CF42 A /2 11-3/4 1/ C1CF43 A /4 1/ C1CF47 A /4 1/ C1CF52 A /16 15/16 3/ C1CF53 A /8 1 3/ C1CF54 A /16 1-1/16 3/ C1CF55 A /4 1-1/8 3/ C1CF56 A /16 1-3/16 3/ C1CF57 A /8 1-1/4 3/ C1CF59 A /8 3/ C1CF60 A /16 1-7/16 3/ C1CF61 A /8 1-1/2 3/ C1CF62 A /16 1-9/16 3/ Pkg. Qty. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1349

20 Seals Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Inch Sizes O-Rings Model Number Dash Size Nominal I.D. 70 Durometer Buna-N O-Rings Nominal O.D. Nominal Width Actual I.D. Actual O.D. Actual Width C1CF63 A /4 1-5/8 3/ C1CF64 A / /16 3/ C1CF65 A /8 1-3/4 3/ C1CF66 A /2 1-7/8 3/ C1CF67 A /8 2 3/ C1CF68 A /4 2-1/8 3/ C1CF69 A /8 2-1/4 3/ C1CF70 A /8 3/ C1CF71 A /8 2-1/2 3/ C1CF73 A /4 2-5/8 3/ C1CF74 A /8 2-3/4 3/ C1CF75 A /2 2-7/8 3/ C1CF76 A /8 3 3/ C1CF77 A /4 3-1/8 3/ C1CF78 A /8 3-1/4 3/ C1CF79 A /8 3/ C1CF80 A /8 3-1/2 3/ C1CF81 A /4 3-5/8 3/ C1CF82 A /8 3-3/4 3/ C1CF83 A /2 3-7/8 3/ C1CF84 A /8 4 3/ C1CF85 A /4 4-1/8 3/ C1CF86 A /8 4-1/4 3/ C1CF87 A /8 3/ C1CF88 A /8 4-1/2 3/ C1CF89 A /4 4-5/8 3/ C1CF90 A /8 4-3/4 3/ C1CF91 A /2 4-7/8 3/ C1CF92 A /8 5 3/ C1CF93 A /4 5-1/8 3/ C1CF94 A /8 5-1/4 3/ C1CF95 A /8 3/ C1CF96 A /8 5-1/2 3/ C1CF97 A /4 5-5/8 3/ C1CF98 A /8 5-3/4 3/ C1CF99 A /2 5-7/8 3/ C1CG11 A /8 6 3/ C1CG12 A /4 6-1/8 3/ C1CG13 A /8 6-1/4 3/ C1CG15 A /4 6-5/8 3/ C1CG16 A /2 6-7/8 3/ C1CG17 A /4 7-1/8 3/ C1CG19 A /4 7-5/8 3/ C1CG20 A /2 7-7/8 3/ C1CG31 A /2 10-7/8 3/ C1CG49 A /2 5 1/ C1CG50 A /8 5-1/8 1/ C1CG51 A /4 5-1/4 1/ C1CG52 A /8 5-3/8 1/ Pkg. Qty. 1350

21 Seals Inch Sizes O-Rings C1CG53 A /2 1/ C1CG56 A /8 5-7/8 1/ C1CG57 A /2 6 1/ C1CG58 A /8 6-1/8 1/ C1CG59 A /4 6-1/4 1/ C1CG60 A /8 6-3/8 1/ C1CG61 A /2 1/ C1CG62 A /4 6-3/4 1/ C1CG63 A /2 7 1/ C1CG64 A /4 7-1/4 1/ C1CG65 A /2 1/ C1CG67 A /2 8 1/ C1CG70 A /2 9 1/ C1CG72 A /2 10 1/ C1ET /2 11 1/ Durometer Buna-N O-Rings Material: 90 Durometer Buna-N. Temperature Range: -40 F. to 240 F. Model Number Model Number Dash Size Dash Size Nominal I.D. Nominal I.D. 70 Durometer Buna-N O-Rings Nominal O.D. 90 Durometer Buna-N O-Rings Nominal O.D. Nominal Width Actual I.D. Actual O.D. Nominal Width Actual I.D. Actual O.D. Actual Width Actual Width C1FA96 A D /8 1/2 1/ C1CD18 A D /2 5/8 1/ C1CE57 A D /4 1 1/ C1FF85 A D /8 1-1/8 1/ C1CE63 A D /4 1/ C1CE69 A D /16 1-9/16 1/ C1CE73 A D /2 1-3/4 1/ C1CE77 A D /8 2-1/8 1/ Pkg. Qty. Pkg. Qty. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1351

22 Seals Hydraulic Power & Control Inch Sizes Back-Up Rings Back-Up Rings Features: Urethane Models: Molded of 90A durometer urethane, these back-up rings provide excellent extrusion resistance. Stretched for installation, they return quickly to their original size for easy installation. Teflon Models: Available in Solid (T suffix), Split (ST suffix) and Spiral Cut (TS suffix). Temperature Range: Urethane Models: -65 F to 220 F. Teflon Models: -40 F to 500 F. Note: Sizes correspond to O-Ring sizes. shown is for each individual back-up ring, not for package. Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control 90A Durometer Urethane Back-Up Rings Model Number Dash Size Type Pkg. Qty C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1BT Urethane C1KK Urethane C1BT Urethane C1BT Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane A Durometer Urethane Back-Up Rings Model Number Dash Size Type Pkg. Qty C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1KK Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane

23 Seals Inch Sizes Back-Up Rings 90A Durometer Urethane Back-Up Rings Model Number Dash Size Type Pkg. Qty C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BU Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane A Durometer Urethane Back-Up Rings Model Number Dash Size Type Pkg. Qty C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane C1BV Urethane Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1353

24 Seals Hydraulic Power & Control Inch Sizes Spiral External Retainer Rings Pneumatic Power & Control Model Number Free I.D. A Thickness B Spiral External Retainer Rings Radial Wall C Shaft Dia. D Groove Dia. E Groove Width F C1DT58 WST Seal Aligning Bearings Fluid Conveying Miscellaneous Products Seal Aligning Bearings Model Number A B W C D C1GG21 HH200ES Indexes & Technical Information 1354

25 Seals Metric Sizes Metric Urethane Rod U-Seals Material: Urethane. Temperature Range: -65 F to 220 F. Pressure Range: 0 to 5000 PSI. Metric Urethane Rod U-Seals Model Number I.D. (mm) O.D. (mm) H (mm) C1ZT15 MRTU-32X40X Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1355

26 Seals Hydraulic Power & Control Assortment Kits & Tools Model Number Description C1BT KIT Kit contains 436 Buna-N 70 Durometer O-Rings in 36 different sizes Kit Contains: (25), 012 (15), (10), 110 (15), (10), (7), (10), (7) Pneumatic Power & Control O-Ring Kit (Buna-N) Model Number Description C1ZT FC-KIT Kit contains 436 Viton (Fluorocarbon) 75 Durometer O-Rings in 36 different sizes Kit Contains: (25), 012 (15), (10), 110 (15), (10), (7), (10), (7) Fluid Conveying O-Ring Kit (Viton ) Model Number Description Kit contains 250 Buna-N 90 C1CA BOSS-KIT Durometer O-Rings in 12 different 0.61 sizes. Kit Contains: 904 (35), (30), (20), (15), 916 (15) Miscellaneous Products Indexes & Technical Information Straight Thread O-Ring Kit Quad Ring Kit Model Number Description C1DJ32 QUAD-KIT Kit contains 226 Buna-N Quad Seals in 36 different sizes Kit Contains: (10), (6), (5), (6), (4), (5) 1356

27 Seals Assortment Kits & Tools O-Ring Face Seal Kit Flange O-Ring Kit Caterpillar D-Ring Kit Metric O-Ring Kit Common Japanese Sizes Model Number Description C1BT FACE-KIT Kit contains 155 Buna-N 90 Durometer O-Rings in 8 different sizes Kit Contains: 011 (25), 012 (25), 014 (25), 016 (25), 018 (20), 021 (15), 025 (10), 029 (10) Model Number Description C1BT FLANGE-KIT Kit contains 70 Buna-N 90 Durometer O-Rings in 7 different sizes Kit Contains: 210 (10), 214 (10), 219 (10), 222 (10), 225 (10), 228 (10), 232 (10) Model Number Description Kit contains the 9 most popular sized C1EW63 CTC-4C4784 D-Rings used on Caterpillar 1.87 equipment. Model Number Description Kit contains 380 Buna-N 70 C1DE79 Durometer Metric O-Rings in 36 of METRIC-O-KIT-J the most popular Japanese metric 0.90 sizes. Kit Contains Following, I.D. mm x Cross Section mm (Qty): 2.8 x 1.9 (25), 3.8 x 1.9 (20), 4.8 x 1.9 (20), 5.8 x 1.9 (20), 6.8 x 1.9 (15), 7.8 x 1.9 (15), 8.8 x 1.9 (15), 9.8 x 1.9 (15), 9.8 x 2.4 (15), 10.8 x 2.4 (15), 11.0 x 2.4 (15), 11.8 x 2.4 (12), 12.8 x 2.4 (12), 13.8 x 2.4 (12), 14.8 x 2.4 (12), 15.8 x 2.4 (12), 17.8 x 2.4 (8), 19.8 x 2.4 (8), 20.8 x 2.4 (8), 21.8 x 2.4 (8), 24.4 x 3.1 (6), 29.4 x 3.1 (7), 21.7 x 3.5 (5), 22.1 x 3.5 (5), 23.7 x 3.5 (7), 24.7 x 3.5 (7), 25.2 x 3.5 (7), 25.7 x 3.5 (7), 27.7 x 3.5 (7), 28.7 x 3.5 (6), 29.2 x 3.5 (6), 29.7 x 3.5 (6), 30.7 x 3.5 (6), 31.2 x 3.5 (6), 14.5 x 4.0 (4), 23.5 x 4.0 (6) Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1357

28 Seals Hydraulic Power & Control Pneumatic Power & Control Assortment Kits & Tools Metric O-Ring Kit Common European Sizes Model Number Description Kit contains 500 Buna-N 70 Durometer Metric O-Rings in 36 of C1DE78 METRIC-O-KIT-E the most popular European metric 0.67 sizes. Kit Contains Following, I.D. mm x Cross Section mm (Qty): 5.0 x 1.5 (20), 13.0 x 1.5 (15), 16.0 x 1.5 (10), 2.2 x 1.6 (20), 3.1 x 1.6 (20), 4.1 x 1.6 (20), 7.1 x 1.6 (20), 9.1 x 1.6 (15), 10.1 x 1.6 (15), 13.1 x 1.6 (15), 4.0 x 2.0 (20), 8.0 x 2.0 (15), 9.0 x 2.0 (15), 10.0 x 2.0 (15), 12.0 x 2.0 (15), 14.0 x 2.0 (10), 16.0 x 2.0 (10), 19.0 x 2.0 (10), 20.0 x 2.0 (10), 4.3 x 2.4 (15), 5.3 x 2.4 (15), 5.6 x 2.4 (15), 6.0 x 2.4 (20), 7.6 x 2.4 (15), 8.3 x 2.4 (15), 8.6 x 2.4 (15), 10.0 x 2.5 (10), 13.0 x 2.5 (10), 14.0 x 2.5 (10), 15.0 x 2.5 (10), 17.0 x 2.5 (10), 18.0 x 2.5 (10), 19.0 x 2.5 (10), 10.0 x 3.0 (10), 11.0 x 3.0 (10), 9.0 x 3.0 (10) Model Number Description Kit contains stock of Buna-N 70 C1BT SPLICE-KIT Durometer O-Ring Cord, Razor Blade, Splicing Tool and Tube of 1.04 Adhesive. Fluid Conveying Miscellaneous Products O-Ring Splice Kit Inch Sizes O-Ring Splice Kit Metric & Inch Sizes Model Number Description Kit can produce O-Rings of any standard inch size cross section plus a wide variety of metric sizes. Kit C1DE77 MET/INCH-SPLICE- contains 14 lengths of Buna-N Durometer O-Ring Cord, Razor Blade, Cutting & Splicing Tool and Tube of Adhesive. Kit Contains: Inch Cross Sections: 1/16, 3/32, 1/8, 3/16, 1/4. Metric Cross Sections (mm): 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 5.0, 5.7, 8.4 Indexes & Technical Information Urethane Back-Up Ring Kit Model Number Description Kit contains 475 Urethane Back-Up C1BV KIT Rings in 24 of the most popular 1.83 sizes. Kit Contains: (25), (25), (15), (10) 1358

29 Seals Assortment Kits & Tools Teflon Back-Up Ring Kit Model Number Description C1ET95 Kit contains 325 Urethane Back-Up Rings in 36 of the most popular 575-PTFE-KIT-S sizes. Rings are scarf cut to facilitate installation Kit Contains: (15), (10), (10), (5), (5) Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1359

30 Seals Hydraulic Power & Control Cylinder Kits & Parts Hyco 70,000 Series Single Acting Telescopic Cylinder Parts Pneumatic Power & Control Fluid Conveying Packing: Normally uses urethane u-seals, but may be retrofitted with vee packing. All sizes are 1/4 inch cross section. Wipers: Urethane snap-in type. Bearings: Nylon bearings. Outer bearing is flat on the top & bottom. Inner bearing is trapped between two retainers. The bottom side of the inner bearing is step-cut on the OD to pilot over snap ring. Cross section is inches. Piston: Welded to stage. Uses 2 replaceable wear rings per stage. Stage OD's: 3, 4, 5, 6, 7, 8-1/8, 9-3/8. Special Info: Spring steel type snap ring serves as internal stop. Uses a spiral retainer to trap lower bearing. Identification: Cylinder model number & serial number stamped on cylinder body near base. Note: 70,000 Series single action cylinders are manufactured using urethane u-seals but may be retrofitted with a vee packing set if desired. Three types of packing kits are offered. Type 1 kits are identical to the original Hyco packing sets and utilize Parker u-seals. Type 2 kits are also identical to the original Hyco packing sets but contain a lower cost Hallite manufactured u-seal. Type 3 kits contain a vee packing set retrofit for the original u-seal packing. The vee packing can be more effective in sealing an older cylinder with abrasive scoring or other surface blemishes. Important: When ordering Hyco telescopic parts, please provide the model number & serial number. Miscellaneous Products Hyco 70,000 Series Single Acting Telescopic Cylinder Parts Model Number Description C1CY90 HY-A2688 Manual Bleeder Valve 0.02 Indexes & Technical Information 1360

31 Control Cables Felsted High Performance Control Cables Miscellaneous Products Felsted cables, controls and control systems are used to control such items as PTO's, manual and automatic transmissions, hydraulic valves, clutches, throttles or accelerators, engine shut-offs, and brakes. Our locations equipped to manufacture cables from stock components are Miami Springs, West Palm Beach, Fort Lauderdale, Belle Glade and Atlanta. Core Construction: Hi-Performance (HP) 1 x 7 coated core is available in 3, 4 and 6 series cables. HP Core utilizes a proprietary coating over 1 x 7 wire rope which offers improved flexibility and higher push loads than armor core construction. Solid stainless steel cores are available in 3 Series Push-Pull, Universal and PTO cables. Liners: All cables utilize polymer liners which have a temperature rating of -65 F to 225 F. Factory lubrication provides optimum core performance without requiring further service. Stranded Conduit: Multiple, oil tempered spring wires are placed in a long lay pattern to protect the liner and inner core, maintain flexibility and withstand extreme compressive and tensile loads. This long lay construction results in minimal deflections during cable operation, assuring precise controlling action to the operator. Conduit Jacket: Heavy duty, thick-walled polymer jackets are extruded onto the stranded liner for maximum cable strength. Standard material is HDPE molded to a dark maroon color. End Fittings: Corrosion resistant materials are used throughout to provide maximum life. Standard 3, 4 and 6 series rods and sleeves are 300 series stainless steel, while hubs are either aluminum or stainless. Seals & Boots: Durable custom compounded seals are used to prevent moisture and contaminants from entering the cable. Rod & Sleeve Bearing: An exclusive polymer rod and sleeve bearing is used to improve efficiency, sealing and cable life by preventing metal to metal contact between the rod and sleeve. They also accurately align the rod with the seal to insure superior sealing and a long cable life. Push-Pull Cables - 3 Series Push Loads To 80 lbs Pull Loads To 120 lbs Cores: Choice of either solid stainless core or HP core. (HP core offers improved flexibility and higher push loads). Hubs: cable assembly has (2) Hubs, which can be the same on each end, or different. Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 3 Inches (HP Core), 6 Inches (Solid Core). Hardware: page 1374 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1361

32 Control Cables Hydraulic Power & Control Push-Pull Cables - 3 Series Push Loads To 80 lbs Pull Loads To 120 lbs Felsted Model Travel O.A. Length Core Hubs N/A MTO-1INCH 1 MTO MTO MTO N/A MTO-2INCH 2 MTO MTO MTO N/A MTO-3INCH 3 MTO MTO MTO Push Rating (lbs) 80(HP) 60(Solid) 80(HP) 50(Solid) 70(HP) 40(Solid) Pull Rating (lbs) 120(HP) 60(Solid) 120(HP) 60(Solid) 120(HP) 60(Solid) A B C D Pneumatic Power & Control N/A MTO-4INCH 4 MTO MTO MTO 60(HP) 30(Solid) 120(HP) 60(Solid) MTO Models: Made-To-Order in specified Travel, O.A. Length, Core material and Hub configuration. Push-Pull Cables - 4 Series Push Loads To 150 lbs Pull Loads To 230 lbs Fluid Conveying Miscellaneous Products Indexes & Technical Information Core: HP Core. Hubs: cable assembly has (2) Hubs, which can be the same on each end, or different. Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (aluminum or stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 5 Inches. Hardware: page 1374 Push-Pull Cables - 4 Series Push Loads To 150 lbs Pull Loads To 230 lbs Felsted Model Travel O.A. Length Hubs Push Pull Rating Rating (lbs) (lbs) A B C D N/A MTO-1INCH 1 MTO MTO N/A MTO-2INCH 2 MTO MTO N/A MTO-3INCH 3 MTO MTO N/A MTO-4INCH 4 MTO MTO N/A MTO-5INCH 5 MTO MTO C1JF Bulkhead / Clamp MTO Models: Made-To-Order in specified Travel, O.A. Length and Hub configuration

33 Control Cables Push-Pull Cables - 6 Series Push Loads To 250 lbs Pull Loads To 400 lbs Core: HP Core. Hubs: cable assembly has (2) Hubs, which can be the same on each end, or different. Hub styles stocked are Bulkhead (aluminum), Clamp (aluminum) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 7 Inches. Hardware: page 1374 Push-Pull Cables - 6 Series Push Loads To 250 lbs Pull Loads To 400 lbs O.A. Length Push Rating (lbs) Pull Rating (lbs) Felsted Model Travel Hubs A B C D N/A MTO-1INCH 1 MTO MTO N/A MTO-2INCH 2 MTO MTO N/A MTO-3INCH 3 MTO MTO N/A MTO-4INCH 4 MTO MTO MTO Models: Made-To-Order in specified Travel, O.A. Length and Hub configuration. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1363

34 Hydraulic Power & Control Control Cables Push-Pull Cables - 8 Series Push Loads To 700 lbs Pull Loads To 1000 lbs Pneumatic Power & Control Core: Armor Core. Hubs: cable assembly has (2) Hubs, which can be the same on each end, or different. Hub styles stocked are Bulkhead (aluminum) and Clamp (aluminum). Minimum Bend Radius: 10 Inches. Hardware: page 1374 Push-Pull Cables - 8 Series Push Loads To 700 lbs Pull Loads To 1000 lbs Fluid Conveying Felsted Model Travel O.A. Length Hubs Push Pull Rating Rating (lbs) (lbs) N/A MTO-1INCH 1 MTO MTO N/A MTO-2INCH 2 MTO MTO N/A MTO-3INCH 3 MTO MTO N/A MTO-4INCH 4 MTO MTO A B C D MTO Models: Made-To-Order in specified Travel, O.A. Length and Hub configuration. Indexes & Technical Information Miscellaneous Products 1364

35 Control Cables Universal Cables - 3 Series Light Duty Core: Choice of either solid stainless core or HP core. (Stainless core offers increased durability, since the core is exposed. HP core offers improved flexibility). Hubs: cable assembly has a Utility Hub (aluminum) on one end, and has a Specified Hub or Plain other end. Specified Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 3 Inches (HP Core), 6 Inches (Solid Core). Hardware & Knobs: page 1374 Felsted Model Universal Cables - 3 Series Light Duty Travel O.A. Length Core Hub N/A MTO-3INCH 3 MTO MTO MTO MTO Models: Made-To-Order in specified Travel, O.A. Length, Core material and Plain End or Hub choice. AA BB Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1365

36 Hydraulic Power & Control Control Cables Universal Cables - 3 Series Heavy Duty Push Loads To 60 lbs Pull Loads To 60 lbs Pneumatic Power & Control Fluid Conveying Miscellaneous Products Core: Choice of either solid stainless core or HP core. (HP core offers improved flexibility and higher push loads). Hubs: cable assembly has a Utility Hub (aluminum) on one end, and has a Specified Hub other end. Specified Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 3 Inches (HP Core), 6 Inches (Solid Core). Hardware & Knobs: page 1374 Universal Cables - 3 Series Heavy Duty Push Loads To 60 lbs Pull Loads To 60 lbs Felsted Model Travel O.A. Length Core Hub N/A MTO-3INCH 3 MTO MTO MTO Push Rating (lbs) 50(HP) 40(Solid) Pull Rating (lbs) 60(HP) 60(Solid) MTO Models: Made-To-Order in specified Travel, O.A. Length, Core material and Hub choice. AA A B C D Indexes & Technical Information 1366

37 Control Cables Universal Cables - 4 Series Push Loads To 120 lbs Pull Loads To 120 lbs Core: HP Core. Hubs: cable assembly has a Utility Hub (aluminum) on one end, and has a Specified Hub other end. Specified Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (aluminum or stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 5 Inches. Hardware & Knobs: page 1374 Universal Cables - 4 Series Push Loads To 120 lbs Pull Loads To 120 lbs O.A. Length Core Hub Push Rating (lbs) Pull Rating (lbs) Felsted Model Travel AA A B C D N/A MTO-3INCH 3 MTO HP MTO MTO Models: Made-To-Order in specified Travel, O.A. Length and Hub choice. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1367

38 Hydraulic Power & Control Control Cables Universal Cables - 6 Series Push Loads To 225 lbs Pull Loads To 225 lbs Pneumatic Power & Control Fluid Conveying Miscellaneous Products Core: HP Core. Hubs: cable assembly has a Utility Hub (aluminum) on one end, and has a Specified Hub other end. Specified Hub styles stocked are Bulkhead (aluminum), Clamp (aluminum) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 7 Inches. Hardware & Knobs: page 1374 Universal Cables - 6 Series Push Loads To 225 lbs Pull Loads To 225 lbs O.A. Length Core Hub Push Rating (lbs) Pull Rating (lbs) Felsted Model Travel AA A B C D N/A MTO-3INCH 3 MTO HP MTO MTO Models: Made-To-Order in specified Travel, O.A. Length and Hub choice. Indexes & Technical Information 1368

39 Control Cables Quick Disconnect Cables - 3 Series Light Duty Push Loads To 20 lbs Pull Loads To 20 lbs Cores: Choice of either solid stainless core or HP core. (Stainless core offers increased durability, since the core is exposed. HP core offers improved flexibility). Head: cable assembly has either a Vernier (aluminum) or Positive Lock Head (aluminum). Vernier Head is ideal for any application requiring coarse or fine adjustment. Positive Lock Head features a T handle that locks the setting when rotated 90. Hub: cable assembly has either a Specified Hub or a Plain end. Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 3 Inches (HP Core), 6 Inches (Solid Core). Hardware: page 1374 Quick Disconnect Cables - 3 Series Light Duty Push Loads To 20 lbs Pull Loads To 20 lbs Felsted Model Travel O.A. Length Head Core Hub N/A MTO-3INCH 3 MTO MTO MTO MTO Push Rating (lbs) 20(HP) 20(Solid) MTO Models: Made-To-Order in specified Travel, O.A. Length, Core material, Head, and Plain End or Hub choice. Pull Rating (lbs) 20(HP) 20(Solid) Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1369

40 Hydraulic Power & Control Control Cables Quick Disconnect Cables - 3 Series Heavy Duty Push Loads To 20 lbs Pull Loads To 20 lbs Fluid Conveying Miscellaneous Products Indexes & Technical Information Pneumatic Power & Control Core: Choice of either solid stainless core or HP core. (HP core offers improved flexibility and higher push loads). Head: cable assembly has either a Vernier (aluminum) or Positive Lock Head (aluminum). Vernier Head is ideal for any application requiring coarse or fine adjustment. Positive Lock Head features a T handle that locks the setting when rotated 90. Hub: cable assembly has a Specified Hub. Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 3 Inches (HP Core), 6 Inches (Solid Core). Hardware: page 1374 Quick Disconnect Cables - 3 Series Heavy Duty Push Loads To 20 lbs Pull Loads To 20 lbs Felsted Model Travel O.A. Length Head Hub N/A MTO-3INCH 3 MTO MTO MTO Push Rating (lbs) 20(HP) 20(Solid) Pull Rating (lbs) 20(HP) 20(Solid) MTO Models: Made-To-Order in specified Travel, O.A. Length, Core material, Head and Hub choice. A B C D

41 Control Cables Quick Disconnect Cables - 4 Series Push Loads To 20 lbs Pull Loads To 20 lbs Core: HP Core. Head: cable assembly has either a Vernier (aluminum) or Positive Lock Head (aluminum). Vernier Head is ideal for any application requiring coarse or fine adjustment. Positive Lock Head features a T handle that locks the setting when rotated 90. Hub: cable assembly has a Specified Hub. Specified Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (aluminum or stainless) and Bulkhead/Clamp Combo (aluminum). The Bulkhead/Clamp Combo Hub is a flexible solution for applications where exact hub type needed is unknown. Minimum Bend Radius: 5 Inches. Hardware: page 1374 Quick Disconnect Cables - 4 Series Push Loads To 20 lbs Pull Loads To 20 lbs O.A. Length Head Hub Push Rating (lbs) Pull Rating (lbs) Felsted Model Travel A B C D N/A MTO-3INCH 3 MTO MTO MTO MTO Models: Made-To-Order in specified Travel, O.A. Length, Head and Hub choice. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1371

42 Hydraulic Power & Control Control Cables Power Take Off (PTO) Cables Push Loads To 50 lbs Pull Loads To 50 lbs Pneumatic Power & Control Fluid Conveying Core: Solid stainless steel core. Minimum Bend Radius: 6 Inches. Hardware: page 1374 Power Take Off (PTO) Cables Push Loads To 50 lbs Pull Loads To 50 lbs Felsted Model Travel O.A. Length C1EL Note: For O.A. Length shorter than 120 inches: (1) Remove core. (2) Cut conduit to length and deburr. (3) Install core. (4) Cut core to length and deburr. Note: For O.A. Length longer than 120 inches, consider using a Universal Cable - 3 Series Light Duty, with a Plain end, and with a Red PTO Knob. Indexes & Technical Information Miscellaneous Products 1372

43 Control Cables Remote Valve Operation (RVO) Cables Push Loads To 100 lbs Pull Loads To 230 lbs Core: HP Core. Hub: cable assembly has a Valve Operator Hub which connects to a Felsted Remote Valve Control (Models 55700, 55709, ), and a Specified Hub. Specified Hub styles stocked are Bulkhead (aluminum or stainless), Clamp (aluminum or stainless) and Universal (aluminum). The Universal style hub is used with a Felsted Valve Connection Kit. Minimum Bend Radius: 5 Inches. Hardware: page 1374 Remote Valve Operation (RVO) Cables Push Loads To 100 lbs Pull Loads To 230 lbs O.A. Length Push Rating (lbs) Pull Rating (lbs) Felsted Model Travel Hub N/A MTO-4INCH 4 MTO MTO MTO Models: Made-To-Order in specified O.A. Length and Hub choice. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1373

44 Hydraulic Power & Control Control Cables Cable Hardware & Knobs Fluid Conveying Pneumatic Power & Control Miscellaneous Products Indexes & Technical Information Cable Hardware & Knobs Felsted Model Description Type A B C D E C1EU Ball Joint, 3 Series A UNF-2B 15/32 9/16 1/4-28 UNF-2A 31/ C1ES Ball Joint, 4 Series A 1/4-28 UNF-2B 15/32 9/16 1/4-28 UNF-2A 31/ C1EZ Ball Joint, 4 Series A 1/4-28 UNF-2B 15/32 7/8 5/16-24 UNF-2A 31/ C1FE Ball Joint, 6 Series A 5/16-24 UNF-2B 17/32 11/16 5/16-24 UNF-2A 1-1/ C1EU Clamp, 3 Series 3/8 1 13/64 1/2 1-1/ C1EZ Clamp, 4 Series 1/2 1 7/32 1/2 1-1/ C1EW Clevis, 3 Series UNF-2B 3/16 7/ / C1EX Clevis, 3 Series UNF-2B 1/4 9/32 1-1/ C1ER Clevis, 4 Series 1/4-28 UNF-2B 1/4 9/32 1-1/ C1EV Clevis, 4 Series 1/4-28 UNF-2B 5/16 11/32 1-7/16 2-1/ C1EW Clevis, 6 Series 5/16-24 UNF-2B 1/4 9/32 1-1/ C1EZ Clevis, 6 Series 5/16-24 UNF-2B 5/16 11/32 1-7/16 2-1/ C1EZ Clevis, 6 Series 5/16-24 UNF-2B 3/8 7/16 1-5/8 2-1/ C1ET Field Clamp 0.20 C1EU Knob, PTO, Red 1/4-20 UNC-2B 0.15 C1ZV Knob, Plain, Black 1/4-20 UNC-2B 0.10 C1KE Knob, Plain, Red 1/4-20 UNC-2B 0.02 C1EN Pivot, 3 Series B 7/64 1/4 5/32 5/16 9/ C1ZT Pivot, 3 Series B 7/64 1/4 19/64 5/16 11/ C1EV Pivot, 4 Series A 1/4-28 UNF-2B 1/4 5/16 1/2 32/ C1EV Pivot, 4 Series A 1/4-28 UNF-2B 3/8 15/32 1/2 1-3/ C1EU Shim, 3 & 4 Series 13/64 1 1/2 3/32 1-1/ C1EW Stop Collar, 3 Series A 7/64 5/16 5/ C1EW Terminal Eye, 4 Series 1/4-28 UNF-2B 1/4 5/8 3/8 1-7/

45 Control Cables Cable Hardware & Knobs Felsted Model Description Type A B C D E C1EX Terminal Eye, 4 Series 1/4-28 UNF-2B 5/16 5/8 3/8 1-7/ C1EW Terminal Eye, 6 Series 5/16-24 UNF-2B 1/4 5/8 3/8 1-7/ C1KH Control, Single Friction B 4.80 C1KK Hub, RVO 0.17 C1KK Hub, 4 Series, RVO 0.06 C1KK Sleeve, RVO 0.03 C1KG Kit 0.02 C1KG Switch/Pin Set 0.15 C1KK Rod Bearing, 8 Series 0.01 C1KK Sleeve, 5" Travel 0.20 Salami Cable Remote Controls For Use with Salami Directional Control Valves Cables: For use with Heavy Duty Cables. Handle Color: Matt black Operating Temperature: -40 F to 176 F Salami Cable Remote Controls For Use with Salami Directional Control Valves Salami Model Stroke Max. Working Load (lb.) Lever Ratio Detent in Neutral Anti-Reverse Device Stackable C1MQ T / :1 No No Yes C1MQ T / :1 No Yes Yes C1MQ T / :1 Yes No Yes C1MQ T / :1 Optional No No Salami Cable Remote Controls Fixing Kits Part Number Description C1MQ T3095 Single lever fixing kit for Stackable Lever controls 3360T3076 and 3360T Lever C1MQ T3105 Single lever fixing kit for Stackable Lever controls 3360T3076 and 3360T Lever 0.50 C1MQ T3106 Single lever fixing kit for Stackable Lever controls 3360T3076 and 3360T Lever C1MQ T3107 Single lever fixing kit for Stackable Lever controls 3360T3076 and 3360T Lever C1MQ T3108 Single lever fixing kit for Stackable Lever controls 3360T3076 and 3360T Lever 1.00 C1MQ T3109 Single lever fixing kit for Stackable Lever controls 3360T3076 and 3360T Lever Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1375

46 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Thread Sealants SAF-T-LOK TPS Anaerobic Sealant Features: White paste in squeeze tube. Seals and locks threaded joints on metal piping systems. Instant seal. Lubricates threads for alignment. Prevents vibration loosening. Resists most industrial chemicals and gasses. Cure Time: Cures totally in 24 hours. Cure can be accelerated with SAF-T-LOK primer. Operating Temperature Range: -100 F to 350 F. Note: Not for use on plastic pipe. Staybond S592 Anaerobic Sealant SAF-T-LOK TPS Anaerobic Sealant SAF-T-LOK Model Size C1DM42 TPS cc 0.16 C1DM41 TPS cc 0.61 Features: White paste in squeeze tube. Instantly seals threaded fittings. Lubricates threads. Prevents galling. Prevents vibration loosening. Resists oils and solvents. Cure Time: Cures totally in 24 hours. Cure can be accelerated with Staybond primer. Operating Temperature Range: -65 F to 350 F. Note: Not for use on plastic pipe. Staybond S592 Anaerobic Sealant Staybond Model Size C1DK64 S ml 0.15 C1DK63 S ml 0.90 Miscellaneous Products Indexes & Technical Information Staybond S569 Anaerobic Hydraulic Sealant Features: Brown, low strength, medium viscosity liquid in bottle. Seals hydraulic fittings and locks mechanical fasteners. Strong resistance to most industrial chemicals. Prevents corrosion between parts. Cure Time: Fixture tight in minutes. Full cure in 24 hours at 72 F. Staybond S569 Anaerobic Hydraulic Sealant Staybond Model Size C1EX13 S ml

47 Thread Sealants SAF-T-LOK HS Anaerobic Hydraulic Sealant Features: Brown, low strength, liquid in bottle. Seals hydraulic fittings and locks fine threads. Instant seal. Lubricates threads. Prevents vibration loosening. Shear Strength: PSI. Cure Time: Cures totally in 24 hours. Cure can be accelerated with SAF-T-LOK primer or heat (200 F for 10 to 20 minutes). Operating Temperature Range: Note: Not for use on plastic pipe. Teflon Tapes SAF-T-LOK HS Anaerobic Hydraulic Sealant SAF-T-LOK Model Size C1CY68 HS cc 0.15 Standard Teflon Tape: Instantly seals threaded fittings. Lubricates threads. Prevents galling. Resists oils and solvents. Pink Plumbers Tape: Superior, high density tape that is not stretched during manufacturing like ordinary Teflon tape. Unasco Gold Tape: A high density thread sealing tape for critical areas. For use on all metal pipe threaded joints where acids, alkalis, oils or solvents are present. Uses include sealing pipe threads on lines for natural gas, LP Gas, butane and propane. Tape is de-greased and can be used on oxygen lines F to 500 F temperature range. Copper Anti-Seize Tape: Made from copper filled Teflon. For general purpose anti-seize applications on most types of metal fasteners. Protects against corrosion, seizure, galling & carbon fusion, rust, galvanic pitting F to 2200 F temperature range. Nickel Anti-Seize Tape: Made from nickel filled Teflon. For anti-seize applications on stainless steel and aluminum. Protects against corrosion, seizure, galling & carbon fusion, rust, galvanic pitting F to 2400 F temperature range. Oxygen Tape: Free of any residual petroleum fraction and is safe to use on oxygen systems F to 500 F temperature range. Teflon Tapes Model Number Description Size C1DM23 TEFLONTAPE Standard Teflon Tape (blue roll/white tape) 1/2 x C1EU45 Pink Plumbers Tape (orange APP104 roll/pink tape) 1/2 x C1EU48 ATG005 Unasco Gold Tape (gold roll/yellow tape) 1/2 x C1EU47 ATC001 Copper Anti-Seize Tape (brown roll/brown tape) 1/2 x C1EU49 ATS001 Nickel Anti-Seize Tape (silver roll/silver tape) 1/2 x Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1377

48 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying SAF-T-LOK T70 Permanent Thread Lock Features: Red liquid in squeeze bottle. Very high strength thread locking & sealing. Locks nuts and screws. Gap filling inches. Shear strength PSI. MIL-S Type I Grade K. ASTM D AN9221. Cure Time: Parts will be fixture tight within one hour. Full cure in 24 hours at 75 F. Staybond T262 Permanent Bolt Lock SAF-T-LOK T70 Permanent Thread Lock SAF-T-LOK Model Size C1ZX39 T cc (1.7 fl.oz.) 0.15 Features: Red liquid in squeeze bottle. High strength thread locking & sealing. MIL-S Type II Grade O. Cure Time: Parts will be fixture tight in minutes. Full cure in 24 hours at 72 F. Staybond T262 Permanent Bolt Lock Staybond Model Size C1EX19 T ml (1.69 fl.oz.) 0.17 Miscellaneous Products Indexes & Technical Information Allied Witan Filter Vents With their low profile, these compact units are most often used as breather vent filters, easily inserted in cylinders, gear boxes, crank cases, storage tanks and other vessels wherever pressure equalization is required. Sintered metal filter. Model F Allied Witan Filter Vents Allied Witan Model Thread Length Hex C1CP37 F18 1/8 NPT C1CP48 F28 1/4 NPT C1CP52 F38 3/8 NPT C1CP54 F48 1/2 NPT

49 Denso Petrolatum Tape Description: Densyl Tape is composed of a non-woven synthetic fabric carrier, fully impregnated with a neutral compound based on saturated petrolatum and inert siliceous fillers. Uses: Densyl Tapes are designed to withstand extreme temperature variations. The tapes provide long term corrosion protection to pipes, flanges, valves and related surfaces. Features: Applied to marginally prepared surfaces Conforms to irregular shapes and profiles Can be applied to cold, wet surfaces Not effected by water, acid, salts or soil organics Encapsulation of lead paint Contains no solvents Meets AWWA C217 Standard Can be applied above and below ground. Properties: Thickness (ASTM D1000) 46 mils. Maximum Service Temperature 158 F. Denso Petrolatum Tape Denso Model Description C1GM81 DENSYL-TAPE-2IN Roll of All Purpose Petrolatum Tape, 2 inches wide x 33 feet long 2.01 Boeshield T-9 Corrosion Shield & Waterproof Lubricant Features: Penetrates deeply into fasteners and fixtures Displaces moisture Dries to a clean waxy film Lubricates and protects all metals for months Will not harm paints, plastics, rubber or vinyl Attacks existing corrosion T-9 will also loosen rusted parts Contains No Fluorocarbons Many Industrial and Household uses Boeshield T-9 Corrosion Shield & Waterproof Lubricant Boeshield Model Description C1JD92 T9 Boeshield T-9 Corrosion Shield, 12 oz Spray Can 1.00 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1379

50 Hydraulic Power & Control Anti-Seizing Products Applications: Nuts, Bolts & Screws Pipe Fittings Boom Guides Valve Assemblies Pump Mountings Chain Drives Shafts Gaskets Press Fit Assemblies Taps & Drills Metal Fittings Machinery Anti-Seizing Products Mfg Model Description C1FG17 NSBT-8 Bostik Never-Seez Regular Grade Anti-Seize, 8 oz, Brush Top 0.64 Fluid Conveying Pneumatic Power & Control Miscellaneous Products Indexes & Technical Information SCRUBS in-a-bucket Hand Cleaner Towels SCRUBS in-a-bucket are the pre-moistened, heavy duty hand cleaner towels that go where you go! SCRUBS in-a-bucket easily removes soil from your hands and leaves them clean and conditioned anywhere you are working. Powerful, yet safe, patented citrus-based formula works together with an absorbent, non-scratching abrasive hand cleaner towel for proven performance. Benefits: Portable and convenient One-step cleaning process Conditions and softens hands Will not transfer soils back onto hands Works fast to loosen, dissolve and absorb dirt, grease and grime Tough, durable bucket that is light and portable. Quickly Removes: Adhesives Caulk Dirt Epoxy Grease Ink & Dye Lubricants Oils Paint Sealant Tar Urethane Wax Asphalt Polyurethane Grime SCRUBS in-a-bucket Hand Cleaner Towels ITW Dymon Model Description C1EK Small Bucket of 30 Hand Towels 1.19 C1EV Large Bucket of 72 Hand Towels 2.65 C1ZT17 MISC-422-WMN Bracket to Surface Mount a Bucket of Hand Towels

51 Cast Bronze Y-Strainers Conbraco s 59 Series Y strainers are lightweight and compact. All sizes offer maximum protection against foreign particles in piping systems and process equipment. Cast bronze body and stainless steel screens are completely corrosion resistant. Self-aligning screen is easily accessed for cleaning or service. Operating pressures up to 400 psig make the 59 Series an excellent choice as a versatile, multipurpose strainer. Sizes 1/8" to 1/2" are perfect for OEM applications and are available as UL recognized components for use as a secondary strainer on oil burning equipment. Optional tapped caps are also available for convenient cleaning of the screen and are not plugged. Working Pressure (Non-Shock): F Steam F Water, Oil, Gas. Self-Aligning Screens: 304 SS (Standard) available in a large variety of meshes (thru 100). Cast Bronze Y-Strainers Conbraco Model Size Description C1EN /4 NPT Standard 304SS 50 mesh screen, 1.38 in² screen area 0.44 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1381

52 Hydraulic Power & Control Precision Splined Hubs Features: Made from low alloy, high carbon steel. Close tolerance O.D. and I.D. concentricity permits accurate mounting of sheave or sprocket. Precision also permits accurate chucking for additional mounting. Pneumatic Power & Control Hub City Model Type Spline Details Precision Splined Hubs Spline O.D. Coupling O.D. Coupling Length C1EX Tooth SAE A 16/32 DP 30 PA / C1AD Tooth SAE B 16/32 DP 30 PA / C1AD Tooth SAE C 12/24 DP 30 PA / C1AD Tooth SAE D 8/16 DP 30 PA / Tire Service Products Fluid Conveying Miscellaneous Products Tire Service Products Dill Model Description C1EU50 D104 Tire Inflator Chuck. For direct connection to live air only. Features a built-in shutoff valve. Solid brass. 1/4 NPT female thread. 300 PSI maximum C1DK87 SK-2043-C Gooseneck Style high pressure coupling with 70 angle PSI working pressure. 10,000 PSI proof pressure. 1/8 NPT female thread C1DK86 Tank Valve (Schraeder Valve) for charging pressure tanks or compressed air chambers. SK Complete with valve core and cap. 1/8 NPT male thread Service Station & Tank Truck Equipment Indexes & Technical Information Service Station & Tank Truck Equipment Dixon Model Description Utility Nozzle. 3/4" inlet, 3/4" spout size. 1 x 3/4 reducer bushing furnished. Die cast metal C1GH70 900S34 body. For use with 12 volt pumps and gravity flow. Applications include construction, farm and 1.65 small utility tanks. C1GH71 900SK Seal Kit for Utility Nozzle

53 Hose Nozzles Hose Nozzles Dixon Model Description C1FC49 FNB75S Textbooks Thermoplastic Fog Nozzle with bumper. Red polycarbonate with brass stem. 3/4 NPS thread. For use with water only up to 100 PSI. Adjusts from straight stream to fog. 120 Spray, PSI. Factory Mutual approved. Textbooks Book Publisher Name of Textbook Description C1JR30 TC E Vickers Industrial Hydraulics Manual Color-illustrated hardbound textbook covering a range of topics related to hydraulics and electrohydraulics, including basic hydraulics principles, electricity and electronics, amplifiers, cartridge valves and circuits Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1383

54 Hydraulic Power & Control Gloves Pneumatic Power & Control Fluid Conveying Gloves Model Description C1HL32 C1HL33 C1HL31 C1JE HSCGLV-LG HSCGLV-XL HSCGLV-2X Anti-vibration Gloves, Large. Heat resistant Amara synthetic leather with impact & vibration absorbing gel pads. Anti-vibration Gloves, Extra Large. Heat resistant Amara synthetic leather with impact & vibration absorbing gel pads. Anti-vibration Gloves, Double Extra Large. Heat resistant Amara synthetic leather with impact & vibration absorbing gel pads. Select split leather palm, leather index finger, leather finger tips, leather thumb and knuckle strap. Wing thumb design with shirred elastic back and striped cotton back with safety cuff. C1JE Cotton poly blend string knit, latex palm, knit wrist C1JD52 1SR8427L Economy string knit with latex palm, knit wrist C1JE pack of disposable latex gloves. Seamless and reversible with rolled cuff C1JM oz. 100% Cotton Jersey Gloves. Clute-cut design with knit wrist Hand Tools Miscellaneous Products Indexes & Technical Information Hand Tools Model Description C1KK63 61CB Channellock 6 in 1 Screwdriver C1JF33 GS-3D Channellock Tongue & Groove Plier Set. 6-1/2", 9-1/2", 12" 2.00 C1JF35 GS-6D Channellock Plier Set. 7" Cutting Plier, 7-1/2" Long Nose Plier, 10" Tongue & Groove Plier 2.19 C1JM CHANNELLO CK Channellock 8 inch Retaining Ring Plier. Capacity 1/4" to 2" External, 3/8" to 2" Internal. Includes Straight Tips, Tips. Easy Switch from External to Internal

55 Pneumatic Piston Vibrators Houston Vibrator BV Series Features: BV Series Pneumatic Piston Vibrators will dislodge problem materials in bins, hoppers, chutes, pipes, railcars, and trucks. All models are available in Impacting or Air Cushioned (silent) configurations. Low initial cost Precision CNC machined bodies and pistons Complete control over force, frequency, and amplitude by regulation of supply air pressure Virtually maintenance free when installed with an HVI Air Preparation Unit. Available Options: Internal Tefkote for lubrication-free operation and high temperature environments External coatings for corrosive or food-grade areas Internal start springs for horizontal mounting Tapped exhaust for routing exhaust air away from vibrator. Pneumatic Piston Vibrators Houston Vibrator BV Series Part No. Houston Vibrator Model Description C1JF16 BV225IMPTESS Pneumatic Piston Vibrator, impacting style, with Tapped Exhaust (TE), Spring Start (SS), capacity 60 cubic foot hopper with 3/16 to 1/4 inch wall Cable (Wire) Ties Cable (Wire) Ties Model Description (pkg) (per pkg) C1KH66 WT-4A 3.8 in long, 10 Assorted Colors, 18 lb Tensile Strength, UV Rated, 100 per package 0.05 C1KH67 WT-7B 7.5 in long, Black, 50 lb Tensile Strength, UV Rated, Mil STD , 100 per package 0.25 C1KH60 WT-11B 11.5 in long, Black, 50 lb Tensile Strength, UV Rated, Mil STD , 100 per package 0.46 C1KH61 WT-14B 14.5 in long, Black, 50 lb Tensile Strength, UV Rated, Mil STD , 100 per package 0.55 C1KH62 WT-15B in long, Black, 120 lb Tensile Strength, UV Rated, Mil STD , 100 per package 0.85 C1KH63 WT-21B in long, Black, 120 lb Tensile Strength, UV Rated, 100 per package 2.00 C1KH64 WT-28B 28.8 in long, Black, 120 lb Tensile Strength, UV Rated, Mil STD , 100 per package 2.61 C1KH65 WT-36B 36.5 in long, Black, 120 lb Tensile Strength, UV Rated, 100 per package 3.84 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1385

56 Hydraulic Power & Control Pneumatic Power & Control Hose Reels Hannay Spring Rewind Hose Reels Hannay Spring Rewind Hose Reels are typically used for lubrication, air, water, air tools, washdown and other general industrial applications. Models with 10,000 psi capability can be used in chassis grease applications. Rewind: A heavy-duty spring motor provides self-contained rewind power. A non-sparking ratchet assembly locks the reel when the desired length of hose has been payed out. A pull on the hose unlocks the reel and the spring motor retracts the hose. A declutching arbor is provided to prevent damage from reverse winding. Inlet: N500 Series: 90 swivel joint with 1/4 Inch Female Pipe. N700 Series: 90 swivel joint with 1/2 Inch Female Pipe. Outlet: N500 Series: 1/4 Inch Female Pipe. N700 Series: 1/2 Inch Female Pipe. Rollers: All models are supplied with a 4-way roller assembly. Hose Stop: A hose stop should be used to prevent damage to rollers and nozzles and to permit adjustment of free hose length. Product Temperature Range: -20 F to 225 F. Fluid Conveying Miscellaneous Products Hannay Model Pressure Rating (psi) Hose Capacity 1/4 ID (ft) Hannay Spring Rewind Hose Reels Hose Capacity 3/8 ID (ft) C1DF67 N J 3, Hose Capacity 1/2 ID (ft) Dimensions A = 10.5 B = 3 C = 8 D = 10 E = F = G = 20 H = J = 10 K = 12 Parts & Accessories For Hannay Spring Rewind Hose Reels Part Number Description C1CY66 HS-3 Hose Stop, plastic, 3 inch OD, ID not drilled (Maximum hole size 1-7/8 in) Indexes & Technical Information 1386

57 Pressure Washer Products High Pressure Hose Assemblies Quick Couplers Pressure Pro Model Miscellaneous Products Hose I.D. Assembly Length (ft) C1MK C1MK C1MK High Pressure Hose Assemblies Pressure Rating (psi) Description Black Hose, with Male x Female QD's, with Bend Restrictor Black Hose, with Male x Female QD's, with Bend Restrictor Grey Hose, with Male x Female QD's, with Bend Restrictor Pressure Pro high flow couplers are non-valved for applications where maximum flow is required. Their smooth, open bore offers low pressure drops and is ideal for applications such as high pressure water and steam washers and carpet cleaners. Socket Half - Female Pipe Socket Half - Male Pipe Plug Half - Female Pipe Quick Couplers Pressure Pro Model Coupling Size Thread Size Body Material Pressure Rating (psi) A C C1BK22 2STF2-B 1/4 1/ Brass 0.17 C1BN23 3STF3-B 3/8 3/ Brass 0.26 C1BR48 4STF4-B 1/2 1/ Brass 0.32 C1EZ78 STFC6 3/4 3/ Brass 1.50 Pressure Pro Model Coupling Size Thread Size Quick Couplers Pressure Rating (psi) Body Material C1JR69 3STM3-B 3/8 3/ Brass 0.24 Pressure Pro Model Coupling Size Thread Size Quick Couplers Pressure Rating (psi) Body Material C1DL57 ST2F2-S 1/4 1/ Plated Steel 0.25 C1DL58 ST3F3-S 3/8 3/ Plated Steel 0.25 C1DL59 ST4F4-S 1/2 1/ Plated Steel 0.25 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1387

58 Hydraulic Power & Control Pneumatic Power & Control Miscellaneous Products Pressure Washer Products Plug Half - Male Pipe Plug Half - Spray Tips Pressure Pro Model Coupling Size Thread Size Quick Couplers Pressure Rating (psi) Body Material C1ER45 ST3M3-S 3/8 3/ Plated Steel 0.08 CAUTION: Brass models wear out sooner than steel models in high pressure applications. Pressure Pro Model Coupling Size Color Nozzle Type Quick Couplers Fan Angle Nozzle Size C1JA Q 1/4 Green Flushing C1JA Q 1/4 White Wash C1JA Q 1/4 Yellow Chiseling C1JC99 MSP4PAK 1/4 See Note 0.17 Red Cutting Nozzles: Concentrated stream that can gouge or cut, can cut stubborn stains from concrete surfaces. Yellow Chiseling Nozzles: Works like a scraper, stripping paint, grease and grime from hard surfaces. Green Flushing Nozzles: Most commonly used nozzle for cleaning dirt from sizing, sidewalks and metal furniture. White Wash Nozzles: Wide spray for washing a large area, usually safe with most surfaces. MSP4PAK: Dixon model. Pack of 4 nozzles. 65 Soap, 15 Yellow, 25 Green, 40 White. Fluid Conveying Miscellaneous Products Indexes & Technical Information Adapters Guns, Wands & Nozzles Pressure Pro Model Description C1EP43 AL456 22MM Male x 3/8-18 Female Pipe 0.12 C1EP44 AL457 22MM Male x 3/8-18 Male Pipe 0.14 C1KE30 C1KG88 Adapters Guns, Wands & Nozzles Pressure Pro Model Description 21290C DL36ICS C1BM (Hypro model) Gun PSI / 10 GPM / 300 F maximum. 3/8 Female NPT inlet. 1/4 Female NPT outlet. Wand PSI / 10.5 GPM / 302 F maximum. 36 inches long with straight end. 1/4 Male NPT both ends. Variable Fan Nozzle PSI / 4.49 GPM / 300 F maximum inch orifice diameter. 0 to 80 adjustable fan pattern (twist to adjust). Push-Pull for pressure adjustment. 1/4 Female NPT inlet

59 Winches RKI (Rawson Koenig) Hydraulic Worm Gear Winches Maximum Line Pull: The maximum line pull of a winch depends upon which cable layer is being used, as shown in the chart, and must not be exceeded. Worm Brake: Applications that involve holding a suspended load should have a worm brake. Winches with brakes must have the cable wound according to the brake setting. Winches with brakes can be ordered either overwind cable spooled over the drum in the direction of the brake housing or underwind cable spooled under the drum in the direction of the brake housing. Drum Clutch: If you wish to pull rope off the drum by hand, a drum clutch is needed. If such freespooling is not needed, a keyed drum will be more reliable. Duty Cycle: Winches are rated for intermittent duty only. Excessive use will cause high oil temperature resulting in rapid oil deterioration, lower efficiency and increased wear. Mounting: Winches should be mounted with the worm shaft horizontal and below the drum. Other arrangements may not provide adequate lubrication. Worm brakes must be mounted below the oil level or they will fail. Available Options: Extra cable capacity, higher line speed, grooved drum barrel, divided drum, galvanizing and stainless steel shafts for improved corrosion resistance, custom mounting, special shafts and power sources are some of the available options. Koenig Model Winch Series RKI (Rawson Koenig) Hydraulic Worm Gear Winches Mounting C1JD33 08HUU-4LASL 08H Upright Worm Brake Rotation Under Wind Worm Gear Ratio 9:1 Worm Gear Hand Drum Shaft Assy Left Hand With Drum Clutch, 3.50 Barrel Dia, 8.25 Flange Dia, 7.87 Barrel Length Std Left Hand Other Features Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1389

60 Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Peel Press Drive Kawasaki / Lantec Peel Press Drive Package Features: 25+ years gear and bearing life expectancy. Extended warranty offered. Supported by factory authorized distributor, Kawasaki authorized QA Center. Double torque arm included. Gearbox: The Lantec HB :1 planetary gearbox design incorporates a floating internal ring gear, which ensures an even distribution of load through the planet gears into the ring gear. A "clash of manufacturing tolerances" is prevented with this floating design. Since the load is evenly distributed, the gears experience even wear, prolonging life. All steel construction. Floating ring gear is heat treated, forged alloy steel. Planet & sun gears are carburized and heat treated steel. All gearing in accordance with A.G.M.A. guidelines. Tapered Timken roller bearings are used in this design. This type of bearing is stronger than "skinny" needle bearings, which are found in competing gearboxes. (Needle bearings are more prone to breakage if mis-aligned). Input shaft and mount will directly accept the Staffa motor. Output shaft is flanged and is ready to bolt down to peel press. Convenient gear lube level indication and fill. Motor: The Kawasaki HMB-150-S Staffa hydraulic motor features hydrostatically balanced con rods for high starting and running torques, and low wear. The motor is simply constructed and is rated at 3600 PSI continuous, 4250 PSI intermittent. A double-lip, double spring shaft seal is in place for efficient low speed sealing. A motor case flushing & cooling circuit is included. Motor is manufactured in an ISO 9002 Certified facility. Life Expectancy Operating Conditions: 28,476 foot pounds torque, 5 RPM, and continuous duty cycle. Gearbox Life Expectancy: Durability (gear pitting life) is calculated at 213,000 operating hours at full load and speed. 213,000 hours divided by 3,500 hours per season = 60+ years gearbox life. Motor Life Expectancy: L10 Bearing Life is calculated at 17,750 hours (front bearing) and 17,580 hours (rear bearing). 17,580 divided by 3,500 hours per season = 5 years motor L10 life. Extended Warranty: We have so much confidence in this package that we offer an extended 3-year warranty from the date of installation. This extended warranty requires a pre-installation inspection of the hydraulic system and system upgrade if required. Please contact us for details on this extended warranty. Kawasaki / Lantec Peel Press Drive HSC Model Description C1DG93 PEEL-PRESS-UNIT Peel Press Drive, complete, including gearbox, motor, motor flange kit and adapters, motor case drain standpipe, motor case flushing & cooling circuit Note: This peel press assembly is NOT kept in stock. Indexes & Technical Information 1390

61 Hydraulic Fluid, Tractor Transmission/Hydraulic Fluid Automatic Transmission Fluid, Gear Lube, Motor Oil Hydraulic Fluid (Anti-Wear, Wide Temperature Range) Mobil D.T.E. 10M Series Description: These antiwear oils meet the demanding requirements of hydraulic systems which operate over a wide temperature range. The highly refined base oils used were selected for optimum flow characteristics at subzero temperatures as well as long term stability in demanding systems. A Viscosity Index (VI) improver system with maximum resistance to shearing and viscosity loss maintains system efficiency and minimizes internal pump leakage losses at high operating temperatures. These oils are approved in the Denison HF-O, Vickers V 104C, Vickers 35VQ25, Sunstrand pumps and Rexroth axial piston pumps Application: Primarily recommended for hydraulic applications where low ambient temperatures or rapid changes from low to high temperatures are encountered. Advantages: Suitable for wide temperature range conditions Superior low-temperature flow properties Outstanding keep-clean performance Stay-In-Grade viscosity under high shear conditions Super stabilized antiwear and water tolerance Good demulsibility, filterability and foam resistance Excellent multimetal compatibility and corrosion resistance. Health & Safety: Based on available toxicological information, these products produce no adverse effects on health when properly handled and used. No special precautions are suggested beyond attention to good personal hygiene including laundering oil-soaked clothing and washing skin-contact areas with soap and water. Material Safety Data Sheets (MSDS) are available upon request. page 1487 Viscosity - Temperature Charts: page 1487 Hydraulic Fluid (Anti-Wear, Wide Temperature Range) Mobil D.T.E. 10M Series Mobil Model Container Size ISO Viscosity Grade C1CN74 DTE-10-EXCEL-32 5 gal 32 Viscosity 32.7cSt@104 F 6.63 cst@212 F Viscosity Index Pour Point Flash Point Gravity, API Specific Gravity (lb) F 482 F NOTE: Lubricating Oil products are NOT stocked at our Distribution Center, and are only available for local pickup at our branch locations. For these products, a BOLD means EVERY branch location stocks it, and a Bulleted means CERTAIN branch locations stock it. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1391

62 Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Hydraulic Fluid, Tractor Transmission/Hydraulic Fluid Automatic Transmission Fluid, Gear Lube, Motor Oil Hydraulic Fluid (Anti-Wear, Super-Stabilized) Mobil D.T.E. 20 Series Description: These oils provide superior antiwear and film strength characteristics for use in severe duty hydraulic systems, and are formulated from stable, high quality, high VI base stocks. The super-stabilized additive system was selected to neutralize the formation of corrosive materials, provide excellent antiwear properties, and multimetal compatibility. This additive system also provides better thin oil film protection against rusting, retention of superior oil cleanliness and improved compatibility with water. These oils are approved in the Denison HFO, Vickers V-104C and 35VQ25, and Sunstrand pump tests. DTE 24, 25 and 26 are qualified against Cincinnati Milicron specifications P-68, P-70 and P-69, respectively. Application: Primarily recommended for most hydraulic applications in industrial, marine and mobile service, including high-pressure systems, systems with servo valves and all robotics. Advantages: Excellent keep-clean performance for systems critical to deposit buildup, such as sophisticated NC control mechanisms Controlled demulsibility allows the oils to work well when contaminated with small amounts of water, and to separate large amounts of water readily Multimetal compatibility under both wet and dry conditions protects pumps using steel and copper alloys Excellent protection against rust Good thin oil film protection for surfaces intermittently wetted by oil Outstanding load-carrying and antiwear properties. Health & Safety: Based on available toxicological information, these products produce no adverse effects on health when properly handled and used. No special precautions are suggested beyond attention to good personal hygiene including laundering oil-soaked clothing and washing skin-contact areas with soap and water. Material Safety Data Sheets (MSDS) are available upon request. Viscosity - Temperature Charts: page 1486 Mobil Model Hydraulic Fluid (Anti-Wear, Super-Stabilized) Mobil D.T.E. 20 Series Container Size ISO Viscosity Grade C1JB78 DTE-24 5 gal 32 C1CN75 DTE-25 5 gal 46 Viscosity 165SSU@100 F 44SSU@210 F 238SSU@100 F 49SSU@210 F Viscosity Index Pour Point Flash Point Gravity, API Specific Gravity F 395 F F 395 F NOTE: Lubricating Oil products are NOT stocked at our Distribution Center, and are only available for local pickup at our branch locations. For these products, a BOLD means EVERY branch location stocks it, and a Bulleted means CERTAIN branch locations stock it. Indexes & Technical Information 1392

63 Hydraulic Fluid, Tractor Transmission/Hydraulic Fluid Automatic Transmission Fluid, Gear Lube, Motor Oil Hydraulic Fluid (Anti-Wear, Biodegradable) Mobil EAL 224H Miscellaneous Products Description: Developed to meet stringent performance requirements, as well as to satisfy needs for a hydraulic oil which is readily biodegradable and virtually nontoxic. Formulated from select, high quality, high VI vegetable oils and additives. Approved in Vickers V-104C and 35VQ25, and various pump tests, and meets the requirements of Denison HF-O and the TP30283A vane pump tests. Application: Primarily recommended for most hydraulic systems operating with oil temperatures in the range of 0 F to 180 F where readily biodegradable and virtually nontoxic fluids are required. It can be used in industrial, marine and mobile service, including high pressure systems, systems with servo valves and all robotics. It may be used in gear applications requiring either an ISO VG 32 or 46 oil with mild extreme-pressure characteristics. Its high viscosity index satisfies other applications requiring an ISO VG 32 or 46 oil. Advantages: A high-performance, readily biodegradable, virtually nontoxic antiwear hydraulic oil Multimetal compatibility protects pumps made of steel and copper alloys Excellent protection against rust Good thin oil film protection of surfaces intermittently wetted by oil Outstanding load-carrying and antiwear properties. Spillage & Disposal: Depending on contamination and/or degradation levels, small amounts of spilled or leaked Mobil EAL 224H will not adversely affect ground water or the environment. For small spills on the ground, the uncontaminated product will readily biodegrade by naturally occurring soil organisms when exposed to air. Nonetheless, spillage of Mobil EAL 224H should be handled similarly to currently accepted methods for conventional mineral oil spills. Mobil EAL 224H does not contain hazardous substances reportable under CERCLA. Since ALL oil spills are reportable, even a spill of the vegetable-based product must be reported to the National Response Center (the U.S. Coast Guard). Local environmental agencies should also be consulted to clarify local requirements. Health & Safety: Based on available toxicological information, these products produce no adverse effects on health when properly handled and used. Material Safety Data Sheets (MSDS) are available upon request. Viscosity - Temperature Charts: page 1487 Mobil Model Hydraulic Fluid (Anti-Wear, Biodegradable) Mobil EAL 224H Container Size ISO Viscosity Grade C1CN87 EAL224H 5 gal 34/46 Viscosity 187SSU@100 F 54SSU@210 F Viscosity Index Pour Point Flash Point Gravity, API Specific Gravity F 428 F NOTE: Lubricating Oil products are NOT stocked at our Distribution Center, and are only available for local pickup at our branch locations. For these products, a BOLD means EVERY branch location stocks it, and a Bulleted means CERTAIN branch locations stock it. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1393

64 Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Hydraulic Fluid, Tractor Transmission/Hydraulic Fluid Automatic Transmission Fluid, Gear Lube, Motor Oil Tractor Transmission/Hydraulic Fluid Mobil Mobilfluid 424 Description: A multipurpose, extreme-pressure, tractor transmission/hydraulic fluid. APPROVED against following specifications: John Deere Quatrol, J20A, J20C. Ford New Holland M2C134D. Massey Ferguson M1135, M1141. White New Idea Q-1802, Q Allison C-4 and Volvo BM. Denison HF-O, HF-1, HF-2. Sauer Sunstrand. EXCEEDS performance requirements of: Case International J/C 145/MS 1210, J/C 185/MS 1204, MS 1205, MS 1206, MS 1207, B6. Deutz-Allis 821XL. Komatsu Dresser B , B Caterpillar TO-2 Powershift. L-20. Ford Type F (Tractor). Dexron and Type A, Suffix A (Tractor). Sunstrand Hydrostatic. Vickers 35VQ25A Pump. Sunstrand 22 Axial Piston Pump. Plessey-Sunstrand Gear Pump. Cincinnati Milacron P-68, P-69, P-70. Copper corrosion (ASTM D 130), 1A Rating. EXCEEDS performance recommendations of: Clark, KH Deutz, Ebru, Fendt, Fiat-Hesston, Hurlimann, International Hough, IMT, Lamborghini, Link Belt, Renk, Schluter, Steyr Daimler Puch, Steiger, Universal, Ursus, Valmet, Zetor. Application: Recommended for top-up and refill of transmissions, differentials, final drives, hydraulics, and power steering systems, as well as wet brakes, PTOs, and hydrostatic drives in farm, contractor, and industrial tractors recommending the above specifications. NOT for use in engine crankcase. NOT for use in passenger car automatic transmissions. Advantages: Considerable improvement in wet brake and PTO chatter control Enhanced shear stability in field service Outstanding low temperature performance Optimized wear protection of gears, pumps and hydraulic valves Improved thermal stability for long service life in severe applications Balanced friction for extended clutch life Good water tolerance and protection from rust and corrosion Freedom from sludge and deposits Good filterability for optimum hydraulic operation. Health & Safety: Based on available toxicological information, these products produce no adverse effects on health when properly handled and used. No special precautions are suggested beyond attention to good personal hygiene including laundering oil-soaked clothing and washing skin-contact areas with soap and water. Material Safety Data Sheets (MSDS) are available upon request. Mobil Model Tractor Transmission/Hydraulic Fluid Mobil Mobilfluid 424 Container Size SAE Grade Viscosity Viscosity Index Pour Point Flash Point Gravity, API Specific Gravity C1BP gal 10W SSU@104 F 43SSU@212 F F 442 F NOTE: Lubricating Oil products are NOT stocked at our Distribution Center, and are only available for local pickup at our branch locations. For these products, a BOLD means EVERY branch location stocks it, and a Bulleted means CERTAIN branch locations stock it. Indexes & Technical Information 1394

65 Hydraulic Fluid, Tractor Transmission/Hydraulic Fluid Automatic Transmission Fluid, Gear Lube, Motor Oil Automatic Transmission Fluid Mobil Multi-Purpose ATF Description: A new generation, premium automatic transmission fluid meeting major U.S. and import car manufacturers' performance requirements. Formulated from special, high quality base oils combined with viscosity index (VI) improvers, antioxidants, antiwear agents, detergents, and defoamants. Contains special friction modifiers or lubricity agents to control the transition from full film to thin film lubrication as a vehicle's band and clutches are activated during shifting. Application: Recommended for make-up and refill in 1974 and later General Motors cars and light trucks, and for make-up and refill in 1988 and later Ford and other vehicles requiring Mercon, as well as 1981 and later Fords requiring an M2C138CJ or M2C166H fluid. May be used in other domestic and imported cars that require a Dexron III, Mercon or Ford Type H fluid. Can be used in off-highway transmission, power steering, and other hydraulic systems requiring a Dexron III or Alison C-4 fluid. Meets industrial hydraulic oil demands of Denison HFO, Vickers vane, and Sunstrand piston pumps. Advantages: Satisfies new car warranty requirements Excellent low-temperature requirements, Smooth, positive shift characteristics under both normal and severe operating conditions Protection against high-temperature deposits during severe service Minimal wear of transmission components Reduced foaming and fluid loss in severe service. Health & Safety: Based on available toxicological information, these products produce no adverse effects on health when properly handled and used. No special precautions are suggested beyond attention to good personal hygiene including laundering oil-soaked clothing and washing skin-contact areas with soap and water. Material Safety Data Sheets (MSDS) are available upon request. Mobil Model C1CK84 ATF 5 gal Red Automatic Transmission Fluid Mobil Multi-Purpose ATF Container Size Color Viscosity 166SSU@104 F 35SSU@212 F Viscosity Index Pour Point Flash Point Gravity, API Specific Gravity F 370 F NOTE: Lubricating Oil products are NOT stocked at our Distribution Center, and are only available for local pickup at our branch locations. For these products, a BOLD means EVERY branch location stocks it, and a Bulleted means CERTAIN branch locations stock it. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1395

66 Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Hydraulic Fluid, Tractor Transmission/Hydraulic Fluid Automatic Transmission Fluid, Gear Lube, Motor Oil Gear Lubricants Mobil Mobilube HD Description: Multipurpose, heavy-duty, extreme pressure gear lubricants. Made with select, specially processed base oils that provide good stability at high temperatures and good performance at low temperatures. The naturally high viscosity index of the base oil, in combination with the sulphur phosphorous additives, results in exceptional chemical and thermal stability. Antiwear and antifriction additives control wear, scoring, and frictional power losses. These lubricants resist foaming, are compatible with normally used seal and gasket materials, and provide good protection against copper corrosion. They have demonstrated protection against rust resulting from water contamination and storage in a humid atmosphere by passing the L-33 rust test of MIL-PRF-2105E. Application: Intended for initial fill, topping-off and refill of enclosed automotive gear cases of manual or semiautomatic transmissions where gear lubricants are recommended, drive axles, and final drives of passenger cars, trucks, taxicabs, and contractor and farm equipment. These products meet U.S. Military Specification MIL-PRF-2105E, and the requirements of the L-37 and L-42 full-scale axle tests, and are fully approved against Mack Truck specifications GO-H and GO-J. Recommended for API GL-5 Service, covering hypoid and other gears in passenger cars and other automotive equipment operated under high-speed shock load, high-speed low torque, and low-speed high torque conditions. Satisfactory for either topping-off or entirely refilling most differentials, except limited-slip types (severity level of limited-slip types may require factory-provided lubricant). Use at bulk oil temperatures up to 300 F is permitted with realistic drain and refill schedules. Steady operation at temperatures above 260 F is NOT recommended. These products should NOT be used in transmissions for which engine oil or automatic transmission fluid is recommended, and should NOT be used when an API GL-4 gear oil is recommended. Mobilube HD 80W-90: Meets the viscosity requirements of SAE 80W, 85W, and 90 grade products, and can be used for temperatures down to -15 F. Mobilube HD 85W-140: Meets the viscosity requirements of SAE 85W, 90W, and 140 grade products, and can be used for temperatures down to 10 F. Advantages: Uninterrupted performance under broad temperature variations Excellent protection against wearing and scoring by high-speed and heavy gear loads Moderate performance in limited slip differentials Superior protection against rusting, staining, corrosion Good thermal stability and foaming resistance Compatible with seals and gaskets. Health & Safety: Based on available toxicological information, these products produce no adverse effects on health when properly handled and used. Material Safety Data Sheets (MSDS) are available upon request. Mobil Model Container Size Gear Lubricants Mobil Mobilube HD SAE Grade C1ER42 SAE85W gal 85W-140 Viscosity 1530SSU@100 F 125SSU@210 F Viscosity Index Pour Point Flash Point Gravity, API F 356 F 24.8 NOTE: Lubricating Oil products are NOT stocked at our Distribution Center, and are only available for local pickup at our branch locations. For these products, a BOLD means EVERY branch location stocks it, and a Bulleted means CERTAIN branch locations stock it. 1396

67 Hydraulic Fluid, Tractor Transmission/Hydraulic Fluid Automatic Transmission Fluid, Gear Lube, Motor Oil Commercial Automotive Engine Oil Exxon XD-3 Extra 15W-40 Exxon XD-3 EXTRA 15W-40 is a super premium quality heavy-duty engine oil that provides outstanding performance in the most severe diesel and gasoline engine applications. Available in an SAE 15W-40 multi-grade, XD-3 EXTRA provides the reliable flow properties of a 15W-40 grade in a cold engine at start-up and the higher-temperature properties of the SAE 40 grade after the engine warms up to operating temperature. Versatile Performance: Exxon XD-3 EXTRA 15W-40 meets API Service Categories CI-4, CH-4, CG-4, CF-4 and CF to provide reliable performance in the latest emission designs, including those with EGR systems, as well as satisfying the needs of older engines. In addition, it meets API SL and SJ requirements for four-stroke gasoline engines. Outstanding Service in Diesel-Powered Equipment: Exxon XD-3 EXTRA 15W-40 can be used where API CI-4, CH-4, CG-4, CF-4, and CF oils are recommended. Additionally, XD-3 EXTRA is approved against Cummins CES 20078, Cummins CES 20076, Cummins 20071, Mack EO-N Premium Plus, Mack EO-N, Mack EO-M Plus, Mack EO-M and Volvo VDS-2 specifications. XD-3 EXTRA has demonstrated excellent performance in the key tests required for the API CI-4 specifications, as well as tests required for OEM specifications. In addition to laboratory engine tests, XD-3 EXTRA additive technology has demonstrated outstanding diesel engine field performance in tests of varying severity. Exxon XD-3 EXTRA is specially formulated to provide excellent performance in all recommended applications. It is extremely resistant to the formation of high-temperature deposits and retains its alkalinity (TBN) over many miles of service. As a result, engines operated with XD-3 EXTRA generally have very low ring-belt deposit levels, and the corrosive wear caused by organic acids is minimized because of the ongoing ability of the oil to neutralize the acids. The excellent dispersancy of XD-3 EXTRA works to keep the cooler areas of the engine virtually free from sludge that can plug oil passages and oil filters and reduce effective lubrication. Formulated for the Severe Demands of Newer Engines: Diesel engines manufactured after October 2002 will be designed to meet very stringent emission requirements. These new engines place more severe demands on a lubricant's oxidation resistance, TBN retention and soot dispersing capabilities. XD-3 EXTRA 15W-40 engine oil is specially formulated for these newer engines and will provide reliable protection against increased heat, acids and soot. Exxon XD-3 EXTRA was specifically formulated to reduce oil make-up requirements. This effect comes for the high-quality base stocks which exhibit lower volatile loss at high temperatures. In addition, XD-3 EXTRA has demonstrated outstanding piston deposit protection. Exxon XD-3 EXTRA 15W-40 can also be used in gasoline engines where API SL or SJ quality oils are recommended. Health & Safety: XD-3 EXTRA should be promptly removed from the skin. Soiled clothing should not remain in contact with the skin. Oils and greases are readily removed from the skin by waterless hand cleaners, followed by washing with soap, water, and a soft skin brush. If petroleum products contact the eyes, flush the eyes with fresh water until the irritation subsides. WARNING: "Empty" containers retain residue (liquid and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks or other sources of ignition; they may explode and cause injury or death. "Empty" drums should be completely drained, properly bunged, and promptly returned to a drum reconditioner. All other containers should be disposed of in an environmentally safe manner and in accordance with governmental regulations. Additional important health and safety information on this product can be found in the Material Safety Data Sheet, available on request. Commercial Automotive Engine Oil Exxon XD-3 Extra 15W-40 Container SAE Viscosity Pour Exxon Model Size Grade Viscosity Index Point C1FW33 XD-3 5 gal. 15W SSU@104 F 72SSU@212 F F Flash Point Gravity, API Note: Lubricating Oil products are NOT stocked at our Distribution Center, and are only available for local pickup at our branch locations. For these products, a BOLD means EVERY branch location stocks it, and a Bulleted means CERTAIN branch locations stock it. Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1397

68 Hydraulic Power & Control CRC Chemical Maintenance Products CRC Chemical Maintenance Products Indexes & Technical Information Miscellaneous Products Fluid Conveying Pneumatic Power & Control Industrial Cleaning CRC Part No. C1MH37 MK2832 C1FR C1FR C1FR Product Spray Away All Purpose Cleaner All Purpose Cleaner/Degreaser Citrus Cleaner/Degreaser Glass Cleaner Professional Strength C1FR Battery Cleaner C1FR QD Contact Cleaner C1MM69 MK2132 C1ML44 MK2032 Cleaning Detail Non-Skid Deck Cleaner On & Off Hull & Bottom Cleaner C1MC31 MK2232 Super Suds Boat Soap C1KZ Rust Remover C1ML45 MK2332 Big Bully Natural Orange Bilge Cleaner Industrial Cleaning Container Size Description 32 fl oz bottle 1 gallon bottle 20 oz aerosol 30 oz trigger bottle 12 oz aerosol 16 oz aerosol 32 fl oz bottle 32 fl oz bottle 32 fl oz bottle 32 fl oz bottle 32 fl oz bottle Cleans grease, grime, oil, rain stains, fish blood and more. Great on virtually any surface. Heavy duty formula is four times stronger than most spray cleaning products. Non-flammable. Biodegradable and concentrated. Non-corrosive, non-abrasive. Non-flammable. Safe on most plastics. Low foaming. Pleasant citrus scent. Leaves no residue. Fast evaporation. Biodegradable. Non-corrosive, non-abrasive, non-staining. Professional strength streak-free glass cleaning. Biodegradable, ready to use. Non-abrasive foaming action. Non-flammable, non-ozone depleting. Removes corrosion quickly while neutralizing acid spills. Assures maximum battery current flow. Promotes longer battery life. Quick drying, leaves no residue, safe on all plastics. Effectively removes soil and other contaminants from electrical and electronic components. Ideal for applications where lower flashpoint solvents can be used. Cleans and brightens fiberglass, stainless steel, chrome, aluminum, and brass. Removes dirt, grease, grime and chalking. Easy to use on most surfaces above the waterline. Great for non-skid decks, shower stalls & tubs. Works instantly to remove the toughest waterline stains, algae stains, rust & gas exhaust stains. Use on fiberglass only. Will not harm gel coat. Highly concentrated synthetic detergent. Non-streaking. Leaves no residue. Cleans away dirt and grime, leaving surfaces sparkling clean. Makes 64 buckets of wash. Will not remove wax. A safe, effective, fast acting formula. Removes rust, not metal. No sand blasting or heavy wire brushing required. Leaves metal clean and ready to paint, plate or powder coat. Works instantly to emulsify oil, grease, & scum. Tough citrus cleaning power absorbs odors and leaves bilge areas clean and fresh. Self-cleaning formula is activated by the rolling action of the boat

69 CRC Chemical Maintenance Products Lubricants CRC Part No. C1FR Product 3-36 Multi-Purpose Lubricant & Corrosion Inhibitor C1FR Food Grade Silicone C1FR C1HC Chain & Wire Rope Lubricant Marine Silicone Lubricant C1FR White Lithium Grease C1FS54 SL35901 Copper Anti-Seize C1FR Copper Anti-Seize C1FS55 SL35911 Nickel Anti-Seize C1JC Screwloose Super Penetrant Vehicle Maintenance CRC Part No. Product C1LW Motor Treatment C1MH C1KT C1GH C1GH Diesel Fuel Therapy Diesel Injector Cleaner Plus Diesel Fuel Therapy Diesel Injector Cleaner with Anti-Gel Bio-Con Diesel Fuel Sludge Sediment Remover Brakleen Brake Parts Cleaner Lubricants Container Size Description 16 oz aerosol 16 oz aerosol 16 oz aerosol 12 oz aerosol 16 oz aerosol 8 oz brush top bottle 16 oz aerosol 8 oz brush top bottle 16 oz aerosol Cleans, lubricates, penetrates and loosens corrosion. Prevents corrosion by displacing moisture. Penetrates through corrosion to loosen frozen parts. Lubricates without leaving a sticky residue. Cleans light soils and contaminants. Meets FDA CFR for incidental food contact. Forms a colorless, odorless, non-staining film. Harmless to most rubbers & plastics. -40 F to 400 F. Excellent release agent and lubricant for all surfaces. Penetrates deep and leaves a tough film that lubricates & protects. Resists water wash-off and high temperature sling-off. Absorbs pin/bushing shock and cushions rollers, pins and bushings. Can be applied with guards in place. A multi-purpose silicone spray. Forms a colorless, odorless, non-staining film that lubricates & protects in most metal to non-metal applications. Dry film eliminates binding & sticking while protecting most surfaces. Excellent heat & water resistance. Rust & oxidation inhibitors for superior metal protection. Smooth, buttery consistency. Produces a tough, high viscosity film. White color for easy visual inspection of film coverage. Copper-based, safe for use on both ferrous and non-ferrous metals. Protects parts up to 1800 F. Electrically conductive. Will not harden. Heat aging won't affect lubricity of product. Copper-based, safe for use on both ferrous and non-ferrous metals. Protects parts up to 1800 F. Electrically conductive. Will not harden. Heat aging won't affect lubricity of product. Copper-free formula for use where a clean, chemically inert & stable lubricant is required. Protects parts up to 2400 F. Electrically conductive. Will not harden. Heat aging won't affect lubricity of product. A no-compromise penetrant that attacks corrosion to free corroded fasteners & mechanical components. A super-fast, powerful, concentrated penetrating solvent that loosens & cleans. Instantly penetrates minute & tightly fitted crevices. Vehicle Maintenance Container Size Description 16 fl oz can 12 fl oz bottle 12 fl oz bottle 12 oz bottle 20 oz aerosol Cleans gum, varnish, and carbon from the fuel system, injectors, pistons, and combustion chamber. Removes moisture from fuel and oil systems and lubricates engine components. This emissions reducing formula is rated "SUPERIOR" in Cummins L-10 Test for injector cleanliness. Cleans injectors, adds lubricity, increases power and MPG. This emissions reducing formula is rated "SUPERIOR" in Cummins L-10 Test for injector cleanliness. Lowers pour point & CFPP, reliquefies gelled fuel, adds lubricity, increases power and MPG. Improves storage stability of fuel. Prevents fuel filter plugging. Absorbs moisture. Keeps injectors clean. Quickly removes brake fluid, grease, oil and other contaminants from brake linings and pads. Cleans fast, dries fast, no residue. Non-flammable. Works without disassembly Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1399

70 Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control CRC Chemical Maintenance Products Electrical Maintenance CRC Part No. Product C1FR Di-Electric Grease C1MG Marine Premium Electronics Grease Corrosion Inhibitors CRC Part No. C1JE C1MH C1MH41 SX32M C1MM26 SX128 C1FR C1FR Greases & Oils Product SP-400 Corrosion Inhibitor Engine Stor Fogging Oil Salt Terminator Engine Fluch, Cleanter & Corrosion Inhibitor Salt Terminator Engine Flush, Cleaner & Corrosion Inhibitor Battery Terminal Protector Zinc-It Instant Cold Galvanize Electrical Maintenance Container Size Description 6 oz pressurized tube 6 oz pressurized tube Non-curing silicone compound used for electrical sealing, lubricating, protecting & insulating. Meets FDA CFR (release agent) and CFR (lubricant, incidental food contact). Excellent lubricant for rubber & plastic parts. Seals, protects & insulates electrical contacts from moisture. Lubricates & seals rubber & plastic parts. Waterproofs components & contacts to protect against arcing. Improves electrical performance during adverse conditions such as rain & fog Corrosion Inhibitors Container Size Description 16 oz aerosol 16 oz aerosol 32 fl oz bottle w/mixer 1 gal bottle 12 oz aerosol 16 oz aerosol Long-term indoor/outdoor corrosion inhibitor that provides protection of all equipment subject to heat, humidity, chemicals or severely corrosive atmospheres. Use on machined surfaces & assemblies subjected to long periods of storage. As fogging fluid, it protects outboard motors, marine engines & internal combustion engines, insures longer life. As long term metal protectant, it keeps pistons, rings & cylinder walls corrosion free. Also protects electrical connections in use/storage. Cleans & protects anything exposed to salt (saltwater, salt air, road salt). Dissolves salt & leaves a protective coating to inhibit corrosion. Essential as a motor flush for marine engines in both saltwater and freshwater environments. Cleans & protects anything exposed to salt (saltwater, salt air, road salt). Dissolves salt & leaves a protective coating to inhibit corrosion. Essential as a motor flush for marine engines in both saltwater and freshwater environments. Soft, flexible film completely encapsulates exposed surfaces and will not become brittle, crack or peel. Dries quickly and protects instantly. Red color for easy visual inspection. Actively fights rust & corrosion with a film of 95% pure zinc. Protects base metal even when scratched or abraded. Fast-drying. Excellent weldability Indexes & Technical Information CRC Part No. Product C1FS53 SL3120 Marine Grease Greases & Oils Container Size Description 14 oz cartridge For boat trailer wheel bearings. Aluminum complex, NLGI #2 grease. Excellent water resistance. Superior rust and corrosion protection. Typical drop point 470 F

71 CRC Chemical Maintenance Products Specialty Products CRC Part No. C1FR C1FR C1FS52 SL1712 C1AK Product RTV Silicone Adhesive/Sealants RTV Silicone Adhesive/Sealants Mechanix Orange Citrus Lotion Hand Cleaner with Pumice Wasp & Hornet Killer PLUS Specialty Products Container Size Description Clear 8 oz pressurize d tube White 8 oz pressurize d tube 16 fl oz bottle 20 oz aerosol Clear - Forms a barely visible water-tight seal. RTV (Room Temperature Vulcanizing) Adhesive/Sealants are designed for a wide range of sealing, bonding, protecting and waterproofing applications. White - Designed for high moisture, indoor/outdoor applications. RTV (Room Temperature Vulcanizing) Adhesive/Sealants are designed for a wide range of sealing, bonding, protecting and waterproofing applications. Fresh citrus scent. Contains no harsh solvents. ph balanced. Conditions skin. Biodegradable. Fortified with pumice for deep-cleaning power. Fast acting, high strength insecticide. Ergonomic trigger that provides control, even with gloved hands, and is accurate up to 15' away Plastic safe - will not damage plastic connectors and other insulating materials Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1401

72 Miscellaneous Products Fluid Conveying Pneumatic Power & Control Hydraulic Power & Control Lubrication Equipment & Accessories Heavy Duty Grease Guns Features: Automatic variable stroke/pressure, air vent fitting, vinyl grip, deluxe pull handle, positive lever stop, heavy-duty one piece head, 3-way loading, loader fitting included. Alemite Model Heavy Duty Grease Guns Pressure Rating (psi) Strokes for 1 oz Other Features C1KK GUN 7, Rigid extension 3.30 C1BR , Rigid extension 3.49 Heavy Duty Deluxe Pistol Grease Gun with 18" Flex Hose Comes with 18" Flex Hose extension for Hard-to-reach Fittings Convenience of One-hand operation for easy Greasing Heavy-duty, LuCast TM, Cast-Alloy Head with Heavier and Reinforced Wall Thickness for Extra Strength Develops up to 7,000 PSI WARNING : Do not hold Whip Hose while pumping the Grease Gun. Replace damaged Whip Hose with 4500 PSI Rated Hose only Handy 3-way loading - fill with Standard Cartridge, Suction or Bulk Fill Air Bleeder Valve to release Trapped Air Filler Nipple with Ball Check for use with Grease Filler Pump Chrome Plated finish Handle for Maximum Protection against Corrosion Deluxe, Oil-resistant, Contoured Grip for Comfort and Firm Grip Heavy Gauge Steel Barrel (18 Ga) Wide Band, Non-slip Knurling for Sure-grip Handling Tough Follower offers Superior Seal and eliminates Grease Bypass Heavy-duty Follower Spring for Consistent Priming Posi-lock Follower Rod with Ergonomically designed T-handle provides Sure-handed Grip and easy filling at any position Outputs 4 oz. of Grease per 100 Strokes Complete with 4" Extension Pipe, Four Hardened Jaws Hydraulic Coupler with Ball Check and Non-drip Cap. Heavy Duty Deluxe Pistol Grease Gun with 18" Flex Hose Lumax Model Description C1JP24 LX-1152 Pistol Grease Gun with 18 inch Flex Hose 3.02 Indexes & Technical Information 1402

73 Lubrication Equipment & Accessories Grease Fitting / Joint Fitting Cleaner For use on stubborn or clogged grease fittings and joints Cleans and replenishes old and dry grease fittings Saves the time and expense of replacing a clogged fitting. How It Works: Pour fluid into cylinder. Lightly tap the head of the plunger after coupler is attached to the fitting. Fluid is dispensed into the fitting. Grease Fitting / Joint Fitting Cleaner Alemite Model Description C1GL Grease Fitting/Joint Cleaner 1.48 Mobilgrease HP Multipurpose Automotive Grease Mobilgrease HP is an NLGI No. 2 unleaded, lithium complex soap grease. It has a smooth structure and is extremely adhesive in service. Mobilgrease HP contains extreme pressure additives and oxidation inhibitors. Base oil viscosity is an ISO Grade 220, dropping point is 500 deg. F, or greater. Application: Mobilgrease HP meets the requirements for extended lubrication intervals of automotive chassis lubrication points and disc brake wheel bearings, particularly in passenger cars, light trucks, taxi fleets and farm equipment. It is also recommended for small marine craft. Mobilgrease HP resists water washout and sprayoff. It provides excellent rust protection as well as protection against wear, making it an excellent choice for on- and off-highway heavy duty equipment (fifth wheels, kingpins, u-joints, bucket pins, etc). Note: When wheel bearings are packed for the first time with Mobilgrease HP, remove the old grease completely, wash the bearings with a suitable safety solvent, and dry them thoroughly before repacking. Health & Safety: Based on available toxicological information, these products produce no adverse effects on health when properly handled and used. No special precautions are suggested beyond attention to good personal hygiene including laundering oil-soaked clothing and washing skin-contact areas with soap and water. Material Safety Data Sheets (MSDS) are available upon request. Mobilgrease HP Multipurpose Automotive Grease Model Number Description C1CX88 GREASE 14 oz. tube. Blue color Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1403

74 Hydraulic Power & Control Pneumatic Power & Control Lubrication Equipment & Accessories Grease Gun Extension Hoses Economical, durable thermoplastic or rubber/wire braided hoses. 12,000 PSI Burst Pressure. Male 1/8 NPT ends. WARNING: The pressure rating on these hose assemblies apply when used with hand-operated grease pumping equipment ONLY, such as grease guns or bucket pumps. DO NOT use with power operated equipment. Couplers Model Mfg. Name Length Grease Gun Extension Hoses Working Pressur e (psi) Hose Type C1ZU96 B A1 Alemite 12 6,000 Thermoplastic 0.18 C1JP25 LX-1203 Lumax 18 4,500 Thermoplastic 0.17 Fluid Conveying Miscellaneous Products Indexes & Technical Information Provides quick, positive, leakproof connection with grease fittings. Grease pressure forces 3 hardened steel jaws against grease fitting. Standard model jaws are reversible for long life. Swivel Couplers Alemite Model Thread Type C1ZV B Female 1/8 NPT Standard 0.11 C1ZV ALEMITE Female 1/8 NPT Narrow 0.07 Note: A equipped with built-in check valve. Couplers Couplers swivel full 360, locks in any of eight positions. Handy means of engaging out-of-the-way grease fittings. Use 1/8 NPT pipe extension to connect coupler to gun outlet. Swivel Couplers Alemite Model Description C1ZU93 B6509-D Standard diameter, metal seal, 3-1/2 inches long 0.37 C1ZU92 B6509-E Narrow diameter, rubber seal, 4 inches long

75 Lubrication Equipment & Accessories Swivels Permits easy handling of control valves and prevents damage to hoses from twisting. Grease Fittings Alemite Model Type Threads C1ZU95 B52750 Straight 1/4 NPT x 1/2-27 NS Taper 0.30 C1JP84 B /4 NPT x 1/2-27 NS Taper 0.62 C1ZU94 B52752 Z-Type 1/4 NPT x 1/2-27 NS Taper 0.91 C1GB62 B Z-Type 1/4 NPT x 1/4 NPT 0.92 Swivels 1/8 NPT Fittings: Used on many industrial machines. Features dirt excluding ball check. Maximum pressure 10,000 PSI. 1/4 NPT Fittings: Widely used for larger bearings on farm machinery and industrial equipment. Especially recommended for heavy lubricants in cold weather. Dirt excluding ball check. Maximum pressure 10,000 PSI. 1/4-28 Taper Thread Fittings: Used on most cars and trucks and on many industrial machines. Dirt excluding ball check. Maximum pressure 10,000 PSI. Alemite Model Thread Type C1BW ARO 1/8 NPT Extra (Mfg is Aro) C1ZV13 C1ZU99 C1ZV12 C1ZV11 B1610-BL (Package of 10) B1688-B (Package of 10) B1627-B (Package of 5) B1641-B (Package of 10) 1/8 NPT Short Straight Extra Short Straight O.A. Length Shank Length Grease Fittings Hex Size / / /8 NPT Extra Short /4 NPT Extra Short Straight 7/ / /4-28 Straight 35/ / Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1405

76 Hydraulic Power & Control Lubrication Equipment & Accessories Non-Corrosive Grease Fittings Alemite non-corrosive fittings withstand the most severe corrosive conditions in both marine and industrial applications, and are never plugged by corrosion. Stainless Steel Models: Identified by a -S in the model number, and 2 notches on hex. Type 303 stainless steel bodies, type 440 stainless steel balls and type 302 stainless steel tempered springs. Monel Models: Identified by a -B in the model number, and 1 notch on hex. Nickel-copper alloy (monel) type R bodies, drawn full hard type R tips, type K monel balls and inconel springs. Pneumatic Power & Control Alemite Model Thread Type C1GF S 1/8 NPT C1GF S 1/4-28 Stainless Extra Short Straight Stainless Straight Non-Corrosive Grease Fittings O.A. Length Shank Length Hex Size 3/4 7/ /32 5/ Fluid Conveying Miscellaneous Products Pocket Pack Grease Fitting Assortment Box contains six types of popular fittings. An identifying chart is included in the cover. C1ZV Metric Grease Fitting Assortment Pocket Pack Grease Fitting Assortment Alemite Model Description (12) 1/8 NPT Straight, (6) 1/8 NPT 45, (6) 1/8 NPT 90, (12) 1/4-28 Straight, (6) 1/ , (6) 1/ Indexes & Technical Information Box contains six types of popular metric fittings. An identifying chart is included in the cover. C1ZV Metric Grease Fitting Assortment Alemite Model Description (10) M6x1 Straight, (6) M6x1 45, (6) M6x1 90, (6) M8x1 Straight, (6) M8x1 90, (10) M10x1 Straight

77 Lubrication Equipment & Accessories Button Head Couplers Needle Nose Adapter Button Head Couplers Alemite Model Thread Type C1ZV A Female 1/8 NPT Standard Pull-On 0.29 For use in all lubrication tight spots. Consists of contact nozzle and coupler locking sleeve. Adapters Bright zinc plated steel to resist corrosion. Couplings Needle Nose Adapter Alemite Model Description C1ZU91 B6783 Needle Nose Adapter, 5 inches long 0.24 Alemite Model Description C1ZV Male 1/4-28 Taper Thread x Female 1/8 NPT 0.02 Alemite Model Description C1ZV Female 3/8 NPT x Female 1/2-27 NS Taper 0.14 Adapters Couplings Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1407

78 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Lubrication Equipment & Accessories Easy-Out Fitting Tools All-in-one tool to extract broken fittings, re-thread holes and install new straight and angle-type fittings. Standard Control Valves Easy-Out Fitting Tools Alemite Model Description C1ZU97 B For fittings with 1/8 NPT thread 0.20 C1ZU98 B For fittings with 1/4-28 taper thread 0.12 Features: Delivers pre-set, measured shots with trigger partially depressed. Provides continuous flow with trigger fully depressed. Includes 6-1/2 inch extension and 6304-B coupler. Female 1/4 NPT inlet. Standard Control Valves Alemite Model Description C1ZV Standard Control Valve, 1/4 NPT 2.82 Miscellaneous Products Indexes & Technical Information Lever-Action Bucket Pump Smooth, easy pumping action dispenses all types of Lubricants, even in the coldest weather. Ideal for transferring Motor Oil, Transmission Fluid, Differential Fluid, Heavier Oils and other Automotive Additives Portable - Clamps to any lb. 5 Gallon Pail All Steel Pump. 1-1/2" Inlet and 1/2" Outlet Port Heavy-duty, LuCast TM, Cast-Alloy Head with Heavier and Reinforced Wall Thickness for Extra Strength and Durability Zinc Plated, Corrosion-resistant Suction Tube Oil-resistant, Contoured Grip for Comfort and Firm Grip Self Priming. Delivers 30 fl. oz. per 12 Strokes Unit Includes : 18" long by 1-1/2" diameter Suction Tube with Rust Resistant 12" Ribbed Cover Assembly with adjusting screws to accommodate variations in drum diameter and 5 ft. Oil Resistant Flex Hose with Curved Nozzle. Lever-Action Bucket Pump Lumax Model Description C1JP26 LX-1300 Lever-Action Bucket Pump

79 Lubrication Equipment & Accessories Plastic Bucket Pump with Flex Hose & Non-Drip Nozzle Plastic Bucket Pump with Zinc-Plated Steel Tube for transferring Noncorrosive Fluids of Light to Medium Viscosity like, Engine Oil, Gear Oils, Transmission Fluid, Automotive Additives, Machine Oil, etc. Self Priming, Push-down Action Pump 5 Gallon Capacity Drain-back Nozzle prevents Spills and Accidents Precision Buna-n Seal eliminates by-pass Nylon Piston for Durability Zinc Plated, Corrosion-resistant Suction Tube Includes : 50 Oil-resistant Flex Hose with Non-drip Nozzle 1" Inlet Port and 1/4" Outlet Port Discharge Capacity : 3 oz. per Stroke Pump Height : 20. Plastic Bucket Pump with Flex Hose & Non-Drip Nozzle Lumax Model Description C1JP28 LX-1336 Plastic Bucket Pump 2.23 Lift-Action Steel Barrel Pump with Fixed Steel Spout Zinc-Plated Steel Barrel Pump for transferring Non-corrosive Fluids of Light to Medium Viscosity like, Motor Oils, Transmission Fluid, Heating Oils, Machine Oil, Automotive Additives, Cleaning Solutions, Lacquer Thinner, Solvents, Diesel Fuel, Kerosene, etc. Fits 55 Gallon Drums (210 l) with Standard 2" Bung Opening Self Priming Die-cast Head with Curved Metal Spout Precision Buna-n Seal eliminates by-pass and Floating Steel Check Valve drains Liquid when not in use Steel Piston for Durability Comes with Adjustable 2" Bung Bushing Zinc Plated, Corrosion-resistant Suction Tube Discharge Spout can be rotated 180 and can be removed to expose Garden Hose threaded outlet Discharge Capacity : 22 Fl. oz. per Stroke 1-1/2" Inlet Port and 3/4" Outlet Port Pump Height : 42". Lift-Action Steel Barrel Pump with Fixed Steel Spout Lumax Model Description C1JP27 LX-1330 Lift-Action Piston-Type Barrel Pump 4.23 Hydraulic Power & Control Pneumatic Power & Control Fluid Conveying Miscellaneous Products Indexes & Technical Information 1409

80 Hydraulic Power & Control Pneumatic Power & Control Lubrication Equipment & Accessories Deluxe Heavy Duty Rotary Action Hand Pump Precision Engineered, Heavy Duty Aluminum Die Cast Body Pump for transferring Non-corrosive Petroleum based fluids of Light to Medium Viscosity Ideal for Heavy-duty use in Industrial, Automotive and Agricultural applications Fits 15 to 55 Gal. Drums (57 to 210 l) with Standard 2" (50 mm) Bung Opening 40" (1 m) long Zinc Plated, Corrosion-resistant Suction Tube Self Priming. Heavy-duty Vanes allow better draw and smooth delivery of Fluids Non-slip, Oil Resistant Grip with for Comfort and Safer Operation Comes with Adjustable 2" (50 mm) Bung Bushing and with 39" (1 m) Flexible, Oil-resistant Discharge Hose 1-1/4" (32 mm) Inlet Port and 1" (25 mm) Outlet Port Discharge Capacity : One Gallon (3.8 l) per 12 Revolutions Pump Height : 4.3 ft. (1.3 m). Maximum Discharge Height : 16.5 ft. (5 m) Funnels Deluxe Heavy Duty Rotary Action Hand Pump Lumax Model Description C1KM72 LX-1320 Rotary Action Transfer Pump 7.50 Fluid Conveying Miscellaneous Products Drain Pans Lumax Model Description C1JP30 48 oz. All-Purpose Plastic Funnel with LX-1604 Hanging Tab C1JP31 6 Quart All-Purpose Plastic Funnel with LX-1608 Hanging Tab C1JP29 LX oz. All-Purpose Plastic Funnel with Hanging Tab Long Neck Utility Funnel for C1JP32 LX-1614 Hard-To-Reach Applications. 5" Diameter x 18" long with 1/2" Tip. With Hanging 0.28 Tab. Funnels Indexes & Technical Information Lumax Model Description 6 Gallon Galvanized Drain Pan. 19" C1JP35 LX-1710 Diameter x 6" Deep. Heavy-Duty with Ribbed Bottom. Anti-Splash Baffle Handles. 15 Quart Drainmaster Drain-Direct Pan C1JP34 with Handle & Wheels. 8" Opening with LX-1632 Screw Cap. Catch-All Basket to Retrieve 2.70 Drain Plug and Filter. O-ring Seal. 6 Quart Plastic Drain Pan with Pouring Lip C1JP33 LX-1628 and Raised Rim Handles. 12" Diameter x " Deep. Drain Pans 1410