4WD SHAFT-DRIVE INSTRUCTION MANUAL

Transcription

1 4WD SHFT-DRIVE 1/18 MICRO CR INSTRUCTION MNUL IT'S FUN, IT'S MICRO, IT'S

2 CONGRTULTIONS The XRY M18 Micro is a unique 1/18th micro-sized model racing car that is the epitome of high-performance and fine distinctive design. Your M18 offers highest performance, responsive handling, and traditionally exceptional XRY quality, engineering, and design. The XRY M18 enters a new frontier in micro-car design by offering fully-adjustable suspension, responsive shaft-drive drivetrain, and ultra-smooth gear differentials. The superb craftsmanship and attention to detail are clearly evident everywhere on the XRY M18. The XRY M18 was created by blending highest-quality materials and excellent design. The result? very affordable, durable, highperformance micro race car that is extremely easy to assemble, drive, and race. On high-speed asphalt tracks or short twisty indoor tracks, whether driving for fun or racing to win, the M18 delivers outstanding performance, speed, and precision handling. M18 can be used for competition micro racing, but is also well suited for novice drivers who choose the XRY M18 as their entrance into the R/C hobby. We have made every effort to make these instructions as easy to understand as possible. However, if you have any difficulties, problems, or questions, please do not hesitate to contact the XRY support team at support@teamxray.com. lso, please visit our web site at to find the latest updates, setup information, option parts, and many other goodies. We pride ourselves on taking excellent care of our customers. R/C TIPS Read and fully understand the instruction manual before building. lways keep this instruction manual ready at hand for quick reference, even after completing the assembly. Make sure all screws are tight. Check them periodically. Make sure that the chassis screws do not protrude from the chassis. For the best performance, it is very important that great care is taken to ensure the free movement of all parts. Clean all ball-bearings so they move very easily and freely. Tap or pre-thread the plastic parts when threading screws. Self-tapping screws cut threads into the parts when being tightened. Do not use excessive force when tightening the self-tapping screws, or you may strip out the thread in the plastic. We recommended you stop tightening a screw when you feel some resistance. sk your local hobby shop for any advice. Please support your local hobby shop. We at XRY Model Racing Cars support all local hobby dealers. Therefore we ask you, if at all possible, to purchase XRY products at your hobby dealer and give them your support like we do. If you have difficulty finding XRY products, please check out to get advice, or contact us via at support@teamxray.com, or contact the XRY distributor in your country. QULITY CERTIFICTE XRY MODEL RCING CRS uses only the highest quality materials, the best compounds for molded parts and the most sophisticated manufacturing processes. We guarantee that all parts of a newlypurchased kit are manufactured with the highest regard to quality. However, due to the many factors inherent in model racecar competition, we cannot guarantee any parts once you start racing the car. We wish you enjoyment of this high-quality and high-performance micro car and wish you best success on the track! In line with our policy of continuous product development, the exact specifications of the kit may vary. In the unlikely event of any problems with your new kit, you should contact the model shop were you purchased it, quoting the part number. We do reserve all rights to change any specification without prior notice. ll rights reserved. 1

3 SYMBOLS USED Part bags used ssemble left and right sides the same way ssemble in the specified order Pay attention here Pivot ball type used pply instant glue Ensure smooth non-binding movement Cut off shadded portion True-to-scale diagram ssemble as many times as specified (here twice) 1 L=R C C 1:1 2x Car orientation Cut off remaining material Cut off remaining material from all plastic parts. Tighten screw gently Self-tapping screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. CORRECT WRONG Overtightened The threads are stripped. TOOLS INCLUDED TOOLS REQUIRED Differential ssembly Tool Phillips Screwdriver 1.5mm llen Wrench Hobby Knife Side Cutters Needlenose Pliers Curved Scissors Hole Reamer EQUIPMENT REQUIRED (Ni-MH recommended) (Typically type) Transmitter Micro Motor Micro Servo Receiver Micro Speed Lexan Paint C Glue 5-Cell Micro Controller Battery Pack Battery Charger Transmitter Batteries 2

4 1. FRONT DIFFERENTIL DIFF SSEMBLY TOOL BG BLL-BERING MR106ZZ 6x10x3 (2) BLL-BERING MR128ZZ 8x12x3.5 (2) COMPOSITE FRONT GER DIFF. + DRIVESHFT PINION GER GERBOX CSE O-RING 4x1 (10) SCREW PHILLIPS 2.2 x 6 (10) WSHER S 3x6x0.3 (10) 3

5 CUT OFF 4x BLCK SHIM LRGER HOLE 3.1mm 1:1 CUT OFF 2x NOTE NOTE SMLLER HOLE 2.6mm SSEMBLED VIEW BLCK SHIM 1:1 CW. TIGHTEN GENTLY DJUST THE DIFF SO IT SPINS SMOOTHLY CCW. TIGHTEN DIFF SCREW (CW) = TIGHTENS DIFF LOOSEN DIFF SCREW (CCW) = LOOSENS DIFF SET DIFF MEDIUM TIGHT SO IT ROTTES SMOOTHLY WITHOUT BINDING x SHIM 3x6x BB 8x12x3.5 4

6 NOTE NOTE LONG SHORT SSEMBLED VIEW SSEMBLED VIEW BB 6x10x O 4x1 5

7 2. RER DIFFERENTIL BG BLL-BERING MR106ZZ 6x10x3 (2) BLL-BERING MR128ZZ 8x12x3.5 (2) PIN 3x16 (10) COMPOSITE RER GER DIFF. + DRIVESHFT PINION GER GERBOX CSE O-RING 4x1 (10) SPUR GER 36T/ WSHER S 3x6x0.3 (10) 6

8 CUT OFF 4x CUT OFF 2x NOTE L SME LENGTH R L=R SSEMBLED VIEW NOTE P 3x BB 8x12x SHIM 3x6x0.3 7

9 NOTE NOTE SHORT LONG SSEMBLED VIEW SSEMBLED VIEW SHORTER LONGER BB 6x10x O 4x1 8

10 3. RER SUSPENSION BG BLL-BERING MR106ZZ 6x10x3 (2) PIN 2x8 (10) COMPOSITE MICRO CHSSIS SET OF SUSPENSION RMS, LOWER + UPPER (2+1+1) COMPOSITE SUSPENSION BLOCK, L+R (2) SET OF LINKGES + BLL JOINTS COMPOSITE DRIVE SHFT - SET (2) SET OF COMPOSITE PIVOT BLLS SCREW PHILLIPS FH 2.5x12 (10) SCREW PHILLIPS 2.2x6 (10) SCREW PHILLIPS 2.2x8 (10) SCREW PHILLIPS 2.5x12 (10) INNER WHEEL DPTORS, F+R 9

11 x L=R 2x RIGHT LOWER RM LEFT LOWER RM B NOTE OF LL PIVOT BLLS B CHECK SME LENGTH L=R L R P 2x8 B 10

12 TECH TIP DJUSTBLE DOWNSTOPS RIGHT LEFT REMOVE DOWNSTOP PIN B THRED SET SCREW NOTE OF LL PIVOT BLLS B L=R RIGHT LEFT L R DOWNSTOP SCREWS SB M3x4 RE IN LST BG B 11

13 LIGN TB ND SLOT BEFORE TIGHTENING SCREW 2x L=R TIGHTEN GENTLY TIGHTEN SCREW, THEN LOOSEN LITTLE BIT CUTWY SSEMBLED VIEW x BB 6x10x x6 12

14 TIGHTEN GENTLY x12 L=R 2x C C x8 SSEMBLED VIEW MKE SURE RMS MOVE FREELY C x x8 13

15 12. SSEMBLED VIEW x12 14

16 4. FRONT SUSPENSION BG BLL-BERING MR106ZZ 6x10x3 (2) PIN 2x8 (10) SET OF SUSPENSION RMS, LOWER + UPPER (2+1+1) COMPOSITE SUSPENSION BLOCK, L+R (2) DJ. TURNBUCKLE 34MM SET OF LINKGES + BLL JOINTS COMPOSITE DRIVE SHFT - SET (2) LU MIN DRIVESHFT- SILVER SET OF COMPOSITE PIVOT BLLS SCREW PHILLIPS FH 2.5x12 (10) SCREW PHILLIPS 2.2x6 (10) SCREW PHILLIPS 2.2x8 (10) SCREW PHILLIPS 2.2x10 (10) SCREW PHILLIPS 2.5x12 (10) INNER WHEEL DPTORS, F+R 15

17 x L=R 2x RIGHT LOWER RM LEFT LOWER RM DO NOT USE DOWNSTOP PIN ON LOWER RMS B CHECK B NOTE OF LL PIVOT BLLS SME LENGTH L=R L R P 2x8 B 16

18 4. TECH TIP DJUSTBLE DOWNSTOPS 5. B REMOVE DOWNSTOP PIN RIGHT LEFT THRED SET SCREW B NOTE OF LL PIVOT BLLS RIGHT LEFT L=R R L B SB M3x4 DOWNSTOP SCREWS RE IN LST BG 17

19 LIGN TB ND SLOT BEFORE TIGHTENING SCREW TIGHTEN GENTLY 2x L=R TIGHTEN SCREW, THEN LOOSEN LITTLE BIT CUTWY SSEMBLED VIEW x BB 6x10x x6 18

20 C C 4x TIGHTEN GENTLY x12 56mm C C SSEMBLED VIEW x8 C x x8 C 19

21 SSEMBLED VIEW MKE SURE RMS MOVE FREELY PLSTIC SHIM x12 20

22 5. FRONT ND RER FINL SSEMBLY BG LOWER FRONT BUMPER FOM BUMPER - BLCK COMPOSITE BODY POSTS (4) + BODY CLIPS COMPOSITE RER BODY POST HOLDER COMPOSITE SHOCK BODY SET (4) SCREW PHILLIPS FH 2.5 x 6 (10) SCREW PHILLIPS FH 2.5 x 8 (10) MICRO BODY CLIP 21

23 L=R x6 22

24 SSEMBLED VIEW SHOCK POSITION SHOCK POSITION x8 PLSTIC SHIM 23

25 6. 7. SSEMBLED VIEW 24

26 6. FINL SSEMBLY BG HEX SCREW SB M3x3 (10) COMPOSITE MOTOR PLTE - SET COMPOSITE SERVO RMS - SET SET OF LINKGES + BLL JOINTS COMPOSITE PINION SET COMPOSITE BTTERY HOLDER SET FOR 5 BT COMPOSITE SERVO MOUNT+ NTENN HOLDER - SET NTENN SET OF COMPOSITE PIVOT BLLS SCREW PHILLIPS 2.0 x 4 (10) SCREW PHILLIPS FH 2.5 x 8 (10) SCREW PHILLIPS 2.2 x 8 (10) SCREW PHILLIPS 2.5 x 8 (10) MICRO BODY CLIP RUBBER TIRES + INSERTS F+R, 40 DEG XRY MICRO WHEEL, F+R 25

27 USE HORN FOR YOUR SERVO USE MICRO SERVO THT IS SIMILR TO OR SMLLER THN THE SERVO SHOWN 1:1 SCREW FROM SERVO SSEMBLED VIEW 90 TIP USE THE MICRO SERVO INCLUDED IN XRY M18 POWER PCK # x x8 26

28 USE MICRO STOCK OR MODIFIED MICRO MOTOR TIGHTEN GENTLY TIP USE XRY MICRO STOCK MOTOR INCLUDED IN XRY M18 POWER PCK # PRE-THRED THE PINION SSEMBLED VIEW SSEMBLED VIEW 1mm x x SB M3x3 27

29 7. TECH TIP THE MOTOR STND IS DJUSTBLE: 1. RELESE SCREWS FROM THE BOTTOM OF CHSSIS 2. MOVE THE MOTOR STND S NEEDED 3. TIGHTEN THE SCREWS INTERNL RTIO 1:2.5 SPUR GER 42 VILBLE OPTION o o o x o o x PINION GER FINL RTIO CCELERTION 36 o x x INCLUDED WITH KIT x SPEED x - INCLUDED WITH KIT o - VILBLE OPTION SPUR GER PINION GER DJUST MOTOR STND SO GERS MESH SMOOTHLY x8 28

30 USE 4 OR 5 CELL PCK OF 2/3 BTTERIES INSTLL RECEIVER (NOT INCLUDED) INSTLL MICRO SPEED CONTROL DOUBLE-SIDED TPE TIP USE MICRO BTTERY PCK INCLUDED IN XRY M18 POWER PCK # TIP USE MICRO SPEED CONTROL XMC180 INCLUDED IN XRY M18 POWER PCK # x8 SCREWS INCLUDED WITH XRY XMC 180 SPEED CONTROL 29

31 RER 2x 2x 2x LRGER C NO SPCE NOTE FRONT 2x 2x 2x C SMLLER NO SPCE NOTE DO NOT USE TOO MUCH GLUE BG 7 30

32 14. PUSH WHEEL TBS LL THE WY INTO THE SLOTS ON THE INNER WHEEL 15. L=R B FRONT 98mm 101mm RER 104mm 107mm PLCE BRKE DISKS DECL ON INNER WHEELS TRCKWIDTH (NRROW) B TRCKWIDTH (WIDE) B B C x8 31

33 ELECTRONICS SSEMBLY M18 POWER PCK SSEMBLY SHOWN NTENN WIRE BTTERY PCK STEERING SERVO MOTOR SPEED CONTROL 1CH 2CH RECEIVER INSTLL ELECTRONICS CCORDING TO MNUFCTURER'S INSTRUCTIONS TIP USE XRY M18 POWER PCK # THT INCLUDES LL ELECTRONICS REQUIRED FOR OPERTION. (RECEIVER & TRNSMITTER RE NOT INCLUDED) 32

34 BODY MOUNTING 4x HOLE FOR BODY POSTS 4.5mm 1x HOLE FOR NTENN 4.5mm 4x HOLE FOR WING 3mm 4.5mm 3mm 4.5mm 4.5mm WING SSEMBLY Cut out body and wing along trim lines pply window masks inside body Mask and paint body using polycarbonate paint pply stickers 33

35 IMPORTNT NOTES This product is not suitable for children except under the direct supervision of an adult. Carefully read all manufacturers warnings and cautions for any parts used in the construction and use of your model. ssemble this kit only in places away from the reach of very small children. First-time builders should seek advice from people who have building experience in order to assemble the model correctly and to allow the model to reach its performance potential. Insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. Exercise care when using tools and sharp instruments. Take care when building; some parts may have sharp edges. Keep small parts out of reach of small children. Do not put fingers or any objects inside or near rotating or moving parts. Immediately after using your model, do NOT touch equipment or electronic components on the model because they may generate high temperatures. Follow the operating instructions for the radio equipment at all times. Be sure that your operating frequency is clear before turning on or running your model, and never share the same frequency with somebody else at the same time. Ensure that others are aware of the operating frequency you are using and when you are using it. lways turn on your transmitter before you turn on the receiver/speed controller or connect the battery pack. lways turn off the receiver/speed controller or disconnect the battery pack before turning your transmitter off. Keep the wheels of the model off the ground when checking the operation of the radio equipment. Disconnect the battery pack before storing your model. When learning to operate your model, go to an area that has no obstacles that can damage your model if your model suffers a collision. Remove any sand, mud, dirt, grass or water before putting your model away. Use a recommended charger for the batteries and follow the instructions correctly. Over-charging, incorrect charging, or using inferior chargers can cause the batteries to become dangerously hot. Regularly check the charger for potential hazards such as damage to the cable, plug, casing or other defects. Ensure that any damage is rectified before using the charger again. Do not allow the transmitter batteries to become low on charge, otherwise you risk losing control of the model. Do not allow any metal part to short circuit the batteries, speed control, or other electrical/electronic device on the model. If the model behaves strangely, immediately stop the model, check and clear the problem. Do not stall the motor. The speed control will fail within seconds if power is applied to the motor when the car cannot move. DO NOT USE YOUR MODEL: Near real cars, animals, or people that are unaware that an R/C car is being driven. In places where children and people gather In residential districts and parks In limited indoor spaces In wet conditions In the street Take adequate safety precautions prior to operating this model. You are responsible for this model s assembly and safe operation. Disregard of the any of the above cautions may lead to accidents, personal injury, or property damage. XRY MODEL RCING CRS assumes no responsibility for any injury, damage, or misuse of this product during assembly or operation, nor any addictions that may arise from the use of this product.

36 XRY MODEL RCING CRS, P.O.BOX 103, TRENČÍN, SLOVKI, EUROPE XRY is a member of mytsn.com