Mark Scheme Q1. Answer Acceptable answers Mark. Question Number. (a) B (1) Answer Acceptable answers Mark. Question Number
|
|
|
- Cuthbert Banks
- 5 years ago
- Views:
Transcription
1 Mark Scheme Q1. (a) B (b) voltmeter symbol connected across battery (c)(i) substitution evaluation 30 give full marks for correct answer, no (W) working (c)(ii) substitution evaluation 4.8 give full marks for correct answer, no (Ω) working (d) (e) An explanation linking any two of the following points greater resistance in the circuit less current (in the circuit) less energy transfer in the coils less voltage across the coils less power generated in the coils Any one from the following points heat will be generated in the resistor it will get hot could burn the rider
2 Q2. (a) (b)(i) (b(ii) (c)(i) (c)(ii) (c)(iii) Answer D a variable resistor connected in parallel with lamp Substitution R = 6.0 / 0.26 Evaluation = 23 point correctly plotted at 2.0, 0.14 to within half a small square smooth curve of best fit connecting all given points within half a small square a description including two of the following: current increases as voltage increases current is not proportional to the pd gradient gets less a suggestion to include: there is still a current (when control is at min position) make the battery last longer Acceptable answers Mark recognisable symbol such as a box with letter V inside or box with the word voltmeter inside it accept voltmeter across both lamp and ammeter An answer which rounds to 23 Give full marks for correct answer no working Judge curve by eye. If more than one line present then ignore any that appear to be erased or deleted. Ignore any part of line which goes beyond given points. If plotted point is incorrect then allow ecf for line Allow reverse argument positive correlation (between them ) graph is not a straight line not in equal steps current does not increase as much (as it gets higher) accept resistance has increased with increase in current for two marks to break the circuit to switch the current off accept flow of electricity/charge/ele ctrons for current battery / energy would be drained /used up/ wasted otherwise accept reverse arguments ignore reference to power / volts
3
4 Q3. Answer (a)(i) D decrease the resistance of the variable resistor (b)(i) correct symbol for ammeter or voltmeter (seen anywhere) one meter connected in parallel with lamp/variable resistor/supply and one meter in series with lamp both meters correctly connected (ammeter in series and voltmeter in parallel with lamp) (b)(ii) substitution evaluation 4 (V) (c) An explanation linking the following points Heat/thermal energy is produced In the lamp/bulb / variable resistor / connecting wires (d) substitution evaluation 2 (W) Acceptable answers Ignore gaps, lines through symbols and wire connected to side of variable resistor Symbols do not have to be correct for this mark voltmeter connected across both components is same as voltmeter connected across supply Symbols do not have to be correct for this mark any shape, labelled ammeter, in series with lamp AND any shape, labelled voltmeter, in parallel with lamp gains marking points 2 and 3 bald 4.0 x 10 n gains 1 mark eg bald 40 or 0.4 = 1 mark (BOD for correct substitution) give full marks for correct numerical answer, 4 (V) even if no working Ignore sound (energy) and 'it is inefficient' Accept 'it' as meaning the lamp Eg 'it also produces heat' gains both marks Idea that (some) energy is wasted/lost in the lamp/variable resistor/wires gains maximum of 1 mark bald 2.0 x 10 n gains 1 mark eg bald 20 or 0.2 = 1 mark (BOD for correct substitution) give full marks for correct numerical answer, 2 Mark (3)
5 (W) no working
6 Q4. Answer Acceptable answers Mark (a)(i) D variable resistor (a)(ii) B in parallel with the lamp (a)(iii) A description including resistance changed (b)(i) (b)(ii ) reduced/decreased/l owered OR voltage/p.d /EMF (of supply) changed increased /turned up/higher both points correct curve of best fit judged by eye remove (variable) resistor /component X number of batteries/number of cells add another cell/battery/battery pack/power pack/power supply allow + / - half square Must pass through zero and two other points. 5 th point can be either (8.0,0.42) or (8.0, 0.44) straight line of best fit through origin tolerance between lines A and B shown on the diagram (c) substitution 10/0.44 or 250/11 evaluation 23 (ohms) (d)(i) an explanation linking two of the 5 th point can be either (8.0,0.42) or (8.0, 0.44) give full marks for correct answer, no working 22.7(ohms),22.73 (ohms), 22.72(ohms) Ignore excessive decimal places. electricity
7 following points electric(al )(energy) (is converted) to heat / thermal (energy) (is converted) to light Total marks for question =10
Exam-style questions: electricity
Exam-style questions: electricity Q. The diagram shows an electrical circuit. (a) Complete the two labels on the diagram. P and Q are meters. What is meter P measuring?... () What is meter Q measuring?...
Circuits-Circuit Analysis
Base your answers to questions 1 through 3 on the information and diagram below. 4. A 9-volt battery is connected to a 4-ohm resistor and a 5-ohm resistor as shown in the diagram below. A 3.0-ohm resistor,
Sharjah Indian School Sharjah Boys Wing
Read the instructions given below carefully before writing the fair record book. The following details are to be written on the LEFT HAND SIDE of the book. CIRCUIT DIAGRAM CALCULATIONS The remaining details
Answer Acceptable answers Mark. Answer Acceptable answers Mark
1(a)(i) Award full marks for correct answer with no working (3) Substitution 2900 = 230 current Transposition 2900 230 Evaluation 13 (A) Allow substitution and transposition in either order Ignore powers
PhysicsAndMathsTutor.com 1
Q1. A battery of emf 9.0 V and internal resistance, r, is connected in the circuit shown in the figure below. (a) The current in the battery is 1.0 A. (i) Calculate the pd between points A and B in the
Unit P.2, P2.3. Currents in electric circuits E ½. F Fuel gauge indicator. Fuel tank. Ammeter. Float. Battery. Sliding contact. Pivot 12V.
Currents in electric circuits 1. The diagram shows the fuel gauge assembly in a car. The sliding contact touches a coil of wire and moves over it. The sliding contact and the coil form a variable resistor.
16.3 Ohm s Law / Energy and Power / Electric Meters
16.3 Ohm s Law / Energy and Power / Electric Meters Voltage Within a battery, a chemical reaction occurs that transfers electrons from one terminal to another terminal. This potential difference across
Which of the following statements is/are correct about the circuit above?
Name: ( ) Class: Date: Electricity Exercises 1. Which of the following statements is/are correct about the circuit above? (1) Electrons flow from right to left through the bulb A. (2) Charges will be used
PHYSICS MCQ (TERM-1) BOARD PAPERS
GRADE: 10 PHYSICS MCQ (TERM-1) BOARD PAPERS 1 The number of division in ammeter of range 2A is 10 and voltmeter of range 5 V is 20. When the switch of the circuit given below is closed, ammeter reading
2. A student sets up the circuit shown. The switch is open (off). Which lamps are on and which lamps are off?
1. A polythene rod repels an inflated balloon hanging from a nylon thread. What charges must the rod and the balloon carry? A The rod and the balloon carry opposite charges. B The rod and the balloon carry
Academic Year
EXCELLENCE INTERNATIONAL SCHOOL First Term, Work sheet (1) Grade (9) Academic Year 2014-2015 Subject: quantities Topics:- Static electricity - Eelectrical NAME: DATE: MULTIPLE CHOICE QUESTIONS: 1 - A circuit
Name: Base your answer to the question on the information below and on your knowledge of physics.
Name: Figure 1 Base your answer to the question on the information below and on your knowledge of physics. A student constructed a series circuit consisting of a 12.0-volt battery, a 10.0-ohm lamp, and
Q2. The diagram shows a network of four 2 Ω resistors. The effective resistance, in Ω, between X and Y is A 0.5 B 1.2 C 1.7. D 2.
Q1. Three identical cells, each of internal resistance R, are connected in series with an external resistor of resistance R. The current in the external resistor is I. If one of the cells is reversed in
ELECTRICITY & MAGNETISM - EXAMINATION QUESTIONS (4)
ELECTRICITY & MAGNETISM - EXAMINATION QUESTIONS (4) 1. Which two electrical quantities are measured in volts? A current and e.m.f. B current and resistance C e.m.f. and potential difference D potential
Higher Homework One Part A. 1. Four resistors, each of resistance 20Ω, are connected to a 60V supply as shown.
Higher Homework One Part A 1. Four resistors, each of resistance 20Ω, are connected to a 60V supply as shown. a) Calculate the total resistance of the circuit. b) Calculate the current drawn from the supply.
Level 3 Physics: Demonstrate understanding of electrical systems Batteries and Kirchoff s Laws - Answers
Level 3 Physics: Demonstrate understanding of electrical systems Batteries and Kirchoff s Laws - Answers In 03, AS 956 replaced AS 9053. The Mess that is NCEA Assessment Schedules. In AS 9053 there was
Essential Electricity Homework Exercise 1
Homework Exercise 1 1. For each of the following electrical symbols, copy the symbol into you jotter and label it using the words below. Word bank resistor, voltmeter, battery, ammeter, bulb V A 2. State
PHYSICS 111 LABORATORY Experiment #3 Current, Voltage and Resistance in Series and Parallel Circuits
PHYSCS 111 LABORATORY Experiment #3 Current, Voltage and Resistance in Series and Parallel Circuits This experiment is designed to investigate the relationship between current and potential in simple series
Mandatory Experiment: Electric conduction
Name: Class: Mandatory Experiment: Electric conduction In this experiment, you will investigate how different materials affect the brightness of a bulb in a simple electric circuit. 1. Take a battery holder,
7.9.2 Potential Difference
7.9.2 Potential Difference 62 minutes 69 marks Page 1 of 20 Q1. A set of Christmas tree lights is made from twenty identical lamps connected in series. (a) Each lamp is designed to take a current of 0.25
7. How long must a 100-watt light bulb be used in order to dissipate 1,000 joules of electrical energy? 1) 10 s 3) 1,000 s 2) 100 s 4) 100,000 s
1. Which quantity must be the same for each component in any series circuit? 1) power 3) current 2) resistance 4) voltage 2. A student needs a 4-ohm resistor to complete a circuit. Only a large quantity
CHAPTER 19 DC Circuits Units
CHAPTER 19 DC Circuits Units EMF and Terminal Voltage Resistors in Series and in Parallel Kirchhoff s Rules EMFs in Series and in Parallel; Charging a Battery Circuits Containing Capacitors in Series and
PAPER 2 THEORY QUESTIONS
PAPER 2 THEORY QUESTIONS 1 A plastic rod is rubbed with a cloth and becomes negatively charged. (a) Explain how the rod becomes negatively charged when rubbed with a cloth... [2] (b) An uncharged metal-coated
Electricity 2 Questions NAT 5
Electricity 2 Questions NAT 5 1) a) A 25W lamp is designed to be used with the mains voltage. Calculate the resistance of the lamp. b) Four of the lamps are connected in parallel. Calculate the total resistance
2. Four 20-Ω resistors are connected in parallel and the combination is connected to a 20- V emf device. The current in any one of the resistors is:
University Physics (Prof. David Flory) Chapt_27 Sunday, February 03, 2008 Page 1 Name: Date: 1. By using only two resistors, R1 and R2, a student is able to obtain resistances of 3 Ω, 4 Ω, 12 Ω, and 16
Data Sheet for Series and Parallel Circuits Name: Partner s Name: Date: Period/Block:
Data Sheet for Series and Parallel Circuits Name: Partner s Name: Date: _ Period/Block: _ Build the two circuits below using two AAA or AA cells. Measure and record Voltage (Volts), Current (A), and Resistance
Circuit Analysis Questions A level standard
1. (a) set of decorative lights consists of a string of lamps. Each lamp is rated at 5.0 V, 0.40 W and is connected in series to a 230 V supply. Calculate the number of lamps in the set, so that each lamp
Electric Circuits Exam
Electric Circuits Exam 1. The diagram below represents a lamp, a 10-volt battery, and a length of nichrome wire connected in series. 4. Which circuit has the smallest equivalent resistance? A) B) As the
INVESTIGATION ONE: WHAT DOES A VOLTMETER DO? How Are Values of Circuit Variables Measured?
How Are Values of Circuit Variables Measured? INTRODUCTION People who use electric circuits for practical purposes often need to measure quantitative values of electric pressure difference and flow rate
Figure 1: (a) cables with alligator clips and (b) cables with banana plugs.
Ohm s Law Safety and Equipment Computer with PASCO Capstone, PASCO 850 Universal Interface Double banana/alligator Cable, 2 Alligator Wires PASCO Voltage Sensor Cable Multimeter with probes. Rheostat Ruler
Chapter Assessment Use with Chapter 22.
Date Period 22 Use with Chapter 22. Current Electricity Understanding Concepts Part A Use each of the following terms once to complete the statements below. ampere electric current potential difference
4.2 Electrical Quantities
For more awesome GSE and level resources, visit us at www.savemyexams.co.uk/ 4.2 Electrical Quantities Question Paper Level IGSE Subject Physics (625) Exam oard Topic Sub Topic ooklet ambridge International
Experiment 3: Ohm s Law; Electric Power. Don t take circuits apart until the instructor says you don't need to double-check anything.
Experiment 3: Ohm s Law; Electric Power. How to use the digital meters: You have already used these for DC volts; turn the dial to "DCA" instead to get DC amps. If the meter has more than two connectors,
34.5 Electric Current: Ohm s Law OHM, OHM ON THE RANGE. Purpose. Required Equipment and Supplies. Discussion. Procedure
Name Period Date CONCEPTUAL PHYSICS Experiment 34.5 Electric : Ohm s Law OHM, OHM ON THE RANGE Thanx to Dean Baird Purpose In this experiment, you will arrange a simple circuit involving a power source
Electricity Unit Review
Science 9 Electricity Unit Review Name: General Definitions: Neutral Object Charge Separation Electrical Discharge Electric Current Amperes (amps) Voltage (volts) Voltmeter Ammeters Galvanometer Multimeter
Farr High School NATIONAL 4 PHYSICS. Unit 1 Electricity and Energy. Revision Notes
Farr High School NATIONAL 4 PHYSICS Unit 1 Electricity and Energy Revision Notes Content Practical electrical and electronic circuits - Measurement of current, voltage and resistance using appropriate
LABORATORY 2 MEASUREMENTS IN RESISTIVE NETWORKS AND CIRCUIT LAWS
LABORATORY 2 MEASUREMENTS IN RESISTIVE NETWORKS AND CIRCUIT LAWS The objective of this experiment is to provide working knowledge of the ammeter, voltmeter, and ohmmeter as well as their limitations in
Physics Experiment 9 Ohm s Law
Fig. 9-1 Simple Series Circuit Equipment: Universal Circuit Board Power Supply 2 DMM's (Digital Multi-Meters) with Leads 150- Resistor 330- Resistor 560- Resistor Unknown Resistor Miniature Light Bulb
Line Check Sheet for Paragliders
Line Check Sheet for Paragliders Glider Type: XB44 Makalu 4 SM (EN B) Rev. No.: 5 Date: 13.01.2016 Piece Check Line lengths [mm] R. Area No. A B C Left Right Left Right Left Right +1 +2 +1 +2 +1 +2 +1
Write the term that correctly completes the statement. Use each term once. ampere. electric current. resistor battery.
Date Period Name CHAPTER 22 Study Guide Current Electricity Vocabulary Review Write the term that correctly completes the statement. Use each term once. ampere electric current resistor battery kilowatt-hour
Figure 1. Figure
Q1.Figure 1 shows a circuit including a thermistor T in series with a variable resistor R. The battery has negligible internal resistance. Figure 1 The resistance temperature (R θ) characteristic for T
EXPERIMENT - 1 OHM S LAW
NOTE: While you copy the practical record see that you are following the note. Write Aim, theory, materials required, procedure, results, discussion and precautions on the right side of your record. While
AP Physics B Ch 18 and 19 Ohm's Law and Circuits
Name: Period: Date: AP Physics B Ch 18 and 19 Ohm's Law and Circuits MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question. 1) A device that produces electricity
PROPERTIES OF ELECTRIC CIRCUITS
Name: PROPERTIES OF ELECTRIC CIRCUITS Date: Go to www.linville.ca and click on the page Computer Simulations or go to http://phet.colorado.edu/simulations open the Circuit Construction: DC and then click
11.1 CURRENT ELECTRICITY. Electrochemical Cells (the energy source) pg Wet Cell. Dry Cell. Positive. Terminal. Negative.
Date: SNC1D: Electricity 11.1 CURRENT ELECTRICITY Define: CIRCUIT: path that electrons follow. CURRENT ELECTRICITY: continuous flow of electrons in a circuit LOAD: device that converts electrical energy
Student book answers Chapter 1
Physics P2 Unit Opener Picture Puzzler: Key Words Picture Puzzler: Close up Everest, newtonmeter, Earth, remote, gear, yellow The key word is energy. copper wires P2 1.1 Charging up In-text A positive,
V=I R P=V I P=I 2 R. E=P t V 2 R
Circuit Concepts Learners should be able to: (a) draw, communicate and analyse circuits using standard circuit symbols using standard convention (b) apply current and voltage rules in series and parallel
The graphs show the voltage across two different types of cell as they transfer the last bit of their stored energy through the torch bulb.
Q1. A small torch uses a single cell to make the bulb light up. (a) The graphs show the voltage across two different types of cell as they transfer the last bit of their stored energy through the torch
Lab # 4 Parallel Circuits
Lab # 4 Parallel Circuits Name(s) Obtain an Electro-Trainer and wire it exactly as shown (Be sure to use the 100 ohm resistor) 1) Record the volt drop and current flow for the Switch, the Resistor and
The rod and the cloth both become charged as electrons move between them.
1 polythene rod is rubbed with a cloth. polythene rod cloth The rod and the cloth both become charged as electrons move between them. The rod becomes negatively charged. Which diagram shows how the rod
AQA GCSE Physics. 55 minutes. 55 marks. Q1 to Q4 to be worked through with tutor. Q5 to Q7 to be worked through independently.
AQA GCSE Physics Magnetism & Electromagnetism 4.7.. - 4.7.2.: Magnets & Electromagnets Name: Class: Date: Time: 55 minutes Marks: 55 marks Comments: Q to Q4 to be worked through with tutor. Q5 to Q7 to
Cambridge International Examinations Cambridge International Advanced Subsidiary and Advanced Level. Published
Cambridge International Examinations Cambridge International Advanced Subsidiary and Advanced Level CHEMISTRY 970/35 Paper 3 Advanced Practical Skills May/June 207 MARK SCHEME Maximum Mark: 40 Published
Ohm s Law. 1-Introduction: General Physics Laboratory (PHY119) Basic Electrical Concepts:
Ohm s Law General Physics Laboratory (PHY119) 1-Introduction: Basic Electrical Concepts: 1- Current (I): Is the flow of electrons through a conductor or semiconductor. For current to flow, it requires
ELECTRICITY: INDUCTORS QUESTIONS
ELECTRICITY: INDUCTORS QUESTIONS No Brain Too Small PHYSICS QUESTION TWO (2017;2) In a car engine, an induction coil is used to produce a very high voltage spark. An induction coil acts in a similar way
Higher - Electricity Powerpoint Answers
Higher - Electricity Powerpoint Answers 1. Electrical current is defined as the number of coulombs of charge that pass a point per second. 2. Potential difference is defined as the energy given to each
Goals. Introduction (4.1) R = V I
Lab 4. Ohm s Law Goals To understand Ohm s law, used to describe behavior of electrical conduction in many materials and circuits. To calculate electrical power dissipated as heat. To understand and use
PHYSICS 6 EXTENDED PHYSICS
PHYSICS 6 EXTENDED PHYSICS GRADE 11 TERM 3 PORTFOLIO TASKS 2013-2014 STS\G11\Portfolio\Extended Physics Assessment Booklet\CDAU\ADVETIVersion 1.0 2014 1 31 Unit/Topic Performance Criteria Assess Event
Class X Chapter 09 Electrical Power and Household circuits Physics
EXERCISE- 9 (A) Question 1: Write an expression for the electrical energy spent in flow of current through an electrical appliance in terms of current, resistance and time. Solution 1: Electrical energy,
Unit 10 Measuring Instruments
Objectives: Unit 10 Discuss the operation of a d Arsonval meter movement. Connect a voltmeter to a circuit. Read an analog multimeter. Connect an ammeter. Measure resistance using an ohmmeter. Analog meters
Current, resistance and potential difference
Multiple choice questions 1. Three conductors join as shown in the diagram. The direction of the current in each conductor is shown by the arrow. Y Z X The current in the conductor Z is 10 A. The current
Chapter 26 DC Circuits. Copyright 2009 Pearson Education, Inc.
Chapter 26 DC Circuits 26-1 EMF and Terminal Voltage Electric circuit needs battery or generator to produce current these are called sources of emf. Battery is a nearly constant voltage source, but does
Chapter 26 DC Circuits
Chapter 26 DC Circuits Electric circuit needs battery or generator to produce current these are called sources of emf. Battery is a nearly constant voltage source, but does have a small internal resistance,
Series and Parallel Circuits Virtual Lab
Series and Parallel Circuits Virtual Lab Learning Goals: Students will be able to Discuss basic electricity relationships Discuss basic electricity relationships in series and parallel circuits Build series,
Investigation Electrical Circuits
ACTIVITY #1 Task: To design and construct a circuit where 2 light bulbs can turn on and off at the same time Materials: - 1 power supply - 2 light bulbs - Connecting wires ( ) - Switch(s) - Multi-meter
P5 STOPPING DISTANCES
P5 STOPPING DISTANCES Practice Questions Name: Class: Date: Time: 85 minutes Marks: 84 marks Comments: GCSE PHYSICS ONLY Page of 28 The stopping distance of a car is the sum of the thinking distance and
Review for formula, circuit and resistance test
Review for formula, circuit and resistance test 1. Fill in the table giving the symbol and unit(s) for each. Current intensity Potential difference Voltage Resistance Power Energy Time 2. Give the formula
Lab 1: DC Motors Tuesday, Feb 8 / Wednesday, Feb 9
Introduction MASSACHUSETTS INSTITUTE OF TECHNOLOGY Department of Electrical Engineering and Computer Science 6.007 Electromagnetic Energy: From Motors to Lasers Spring 2011 Do the pre-lab before you come
Laboratory Exercise 12 THERMAL EFFICIENCY
Laboratory Exercise 12 THERMAL EFFICIENCY In part A of this experiment you will be calculating the actual efficiency of an engine and comparing the values to the Carnot efficiency (the maximum efficiency
Current Electricity. GRADE 10 PHYSICAL SCIENCE Robyn Basson CAPS
Current Electricity GRADE 10 PHYSICAL SCIENCE Robyn Basson CAPS What is current electricity? The flow of moving charge, usually carried by moving electrons in a wire. Circuits A path in which charges continually
Problems with your 12/24V Booster?
Problems with your 12/24V Booster? Check this Trouble Shooting Manual for your answer 1. Tools Required 2. First Tests to conduct 2.1 Measure the Voltage at the Clamps 2.2 Testing the power (Amps) 3. Testing
Measurement request from test house for CCC certification From 28/09/2014 to next revision
Measurement request from test house for CCC certification From 28/09/2014 to next revision Brand Model Size Skywalk X-Alps2 S Test house name DHV Musterprüfstelle CCC certification n DHV GS-CCC-005-15
Lab 2 Electrical Measurements and Ohm s Law
Lab 2 Electrical Measurements and Ohm s Law Safety and Equipment No special safety precautions are necessary for this lab. Computer with PASCO Capstone, PASCO 850 Universal Interface Double banana/alligator
CLASSIFIED 5 MAGNETISM ELECTROMAGNETIC INDUCTION GENERATOR MOTOR - TRANSFORMER. Mr. Hussam Samir
CLASSIFIED 5 MAGNETISM ELECTROMAGNETIC INDUCTION GENERATOR MOTOR - TRANSFORMER Mr. Hussam Samir EXAMINATION QUESTIONS (5) 1. A wire perpendicular to the page carries an electric current in a direction
Problems with your 12V Booster?
Problems with your 12V Booster? Check this Trouble Shooting Manual for your answer 1. Tools Required 2. First Tests to conduct 2.1 Measure the Voltage at the Clamps 2.2 Testing the power (Amps) 3. Testing
Chapter 27. Circuits
Chapter 27 Circuits 27.2: Pumping Charges: In order to produce a steady flow of charge through a resistor, one needs a charge pump, a device that by doing work on the charge carriers maintains a potential
Work done and Moment. When using the equipment, John wants to do 300J of work in each lift.
Yr 11 Physics worksheet Paper 2 Work done and Moment Q1) The diagram shows weightlifting equipment found in most gyms. When using the equipment, John wants to do 300J of work in each lift. He can vary
What does the measure? I
TOP 17 urrent Electricity 1 Which of the following is a correct unit for electrical energy? 5 The diagrams show the symbols and ranges of five meters. ampere Which meter should be used to measure a current
INTERACTIVE SCIENCE 2A
INTERACTIVE SCIENCE 2A Workbook Solutions (Enrichment Edition) Chapter 8 MAKING USE OF ELECTRICITY Part A Sectional Exercise 8.1 & 8.2 Concept checking p.35 1. False 2. True 3. False 4. True 5. True Questions
PHA3/W PHYSICS (SPECIFICATION A) Unit 3 Current Electricity and Elastic Properties of Solids
Surname Centre Number Other Names Candidate Number Leave blank Candidate Signature General Certificate of Education June 2005 Advanced Subsidiary Examination PHYSICS (SPECIFICATION A) PHA3/W Unit 3 Current
ELECTRICIANS REGULATIONS EXAMINATION 29 June 2013 QUESTION AND ANSWER BOOKLET
ER52 Candidate Code No. For Board Use Only Result Date Result Date Int ELECTRICIANS REGULATIONS EXAMINATION 29 June 2013 QUESTION AND ANSWER BOOKLET Time Allowed: Three hours INSTRUCTIONS READ CAREFULLY
Page 2. M1. (a) (i) E-F (ticked) 1. (ii) B-C or D-E accept both answers 1. accept downhill 1. slow(er) 1. force do not accept distance 1 [5]
![Page 2. M1. (a) (i) E-F (ticked) 1. (ii) B-C or D-E accept both answers 1. accept downhill 1. slow(er) 1. force do not accept distance 1 [5]](/thumbs/82/86929946.jpg "Page 2. M1. (a) (i) E-F (ticked) 1. (ii) B-C or D-E accept both answers 1. accept downhill 1. slow(er) 1. force do not accept distance 1 [5]")
M. (a) (i) E-F (ticked) B-C or D-E accept both answers fast(er) accept downhill slow(er) force do not accept distance [5] Page M. (a) 53 (m) (i) Similar shape curve drawn above existing line going through
move a (magnetic / plotting) compass around the wire 1 the changing direction of the compass needle shows a magnetic field has been produced
M.(a) move a (magnetic / plotting) compass around the wire the changing direction of the compass needle shows a magnetic field has been produced OR sprinkle iron filings onto the card () tapping the card
Electricity and Magnetism. Introduction/Review
Electricity and Magnetism Introduction/Review Overall Expectations By the end of this unit, students will: 1. Analyse the social, economic, and environmental impact of electrical energy production and
Chapter 9 Motion Exam Question Pack
Chapter 9 Motion Exam Question Pack Name: Class: Date: Time: 63 minutes Marks: 63 marks Comments: Page of 49 The graphs in List A show how the velocities of three vehicles change with time. The statements
Section 6 HOW ARE VALUES OF CIRCUIT VARIABLES MEASURED?
Section 6 HOW RE VUES OF CIRCUIT VRIBES MESURED? INTRODUCTION People who use electric circuits for practical purposes often need to measure quantitative values of electric pressure difference and flow
Circuit Notes. Def: 1. Power supply:
Circuit Notes Def: Parts of a circuit 1. Power supply: Types: 1- photovoltaic cell: generates current when exposed to light. ex: solar calculator or watch. 2- Batteries and generators. 2. Wires: 3. Switch
EXPERIMENT 19. Starting and Synchronizing Synchronous Machines PURPOSE: BRIEFING: To discover the method of starting synchronous motors.
EXPERIMENT 19 Starting and Synchronizing Synchronous Machines PURPOSE: To discover the method of starting synchronous motors. BRIEFING: When three-phase is applied to the stator of a three-phase motor,
Electric Current. Electric current: is the movement of electrons from a negative terminal back to the positive terminal of a battery.
Electric Current Electric current: is the movement of electrons from a negative terminal back to the positive terminal of a battery. Electric Current Electrons flow from regions of high Potential Energy
Electromagnetic Induction
Electromagnetic Induction Question Paper Level ubject Exam oard Unit Topic ooklet O Level Physics ambridge International Examinations Electricity and Magnetism Electromagnetic Induction Question Paper
Laboratory 5: Electric Circuits Prelab
Phys 132L Fall 2018 Laboratory 5: Electric Circuits Prelab 1 Current and moving charges Atypical currentinanelectronic devicemightbe5.0 10 3 A.Determinethenumber of electrons that pass through the device
15 Electrical Circuits Name Worksheet A: SERIES CIRCUIT PROBLEMS
Worksheet A: SERIES CIRCUIT PROBLEMS be careful to use proper significant figures on all answers 1. What would be the required voltage of an energy source in a circuit with a current of 10.0 A and a resistance
CHAPTER 2 ELECTRIC CIRCUIT
CHAPTE 2 ELECTIC CICUIT 1 Electric charges Two kinds of charges Who carry those charges? Unit of charge 2 Flow of charge and electric current The true picture of a circuit Page 1 The conventional picture
Pre-lab Quiz/PHYS 224 Ohm s Law and Resistivity. Your name Lab section
Pre-lab Quiz/PHYS 224 Ohm s Law and Resistivity Your name Lab section 1. What do you investigate in this lab? 2. When 1.0-A electric current flows through a piece of cylindrical copper wire, the voltage
Application Notes. Calculating Mechanical Power Requirements. P rot = T x W
Application Notes Motor Calculations Calculating Mechanical Power Requirements Torque - Speed Curves Numerical Calculation Sample Calculation Thermal Calculations Motor Data Sheet Analysis Search Site
APPARATUS AND MATERIAL REQUIRED Resistor, ammeter, (0-1.5A) voltmeter (0-5V ), battery, one way key, rheostat, sand paper, connecting wires.
ACTIVITIES ACTIVITY 1 AIM To assemble the components of a given electrical circuit. APPARATUS AND MATERIAL REQUIRED Resistor, ammeter, (0-1.5A) voltmeter (0-5V ), battery, one way key, rheostat, sand paper,
Let's start our example problems with a D'Arsonval meter movement having a full-scale deflection rating of 1 ma and a coil resistance of 500 Ω:
Voltmeter design As was stated earlier, most meter movements are sensitive devices. Some D'Arsonval movements have full-scale deflection current ratings as little as 50 µa, with an (internal) wire resistance
Electric Circuits Lab
Electric Circuits Lab Purpose: To construct series and parallel circuits To compare the current, voltage, and resistance in series and parallel circuits To draw schematic (circuit) diagrams of various
Chapter 28. Direct Current Circuits
Chapter 28 Direct Current Circuits Direct Current When the current in a circuit has a constant magnitude and direction, the current is called direct current Because the potential difference between the
ELECTRICAL. CDTA Technical Training Center
ELECTRICAL ATOMIC STRUCTURE Protons positive charge Electron negative charge Neutron - neutral Electricity is the movement of electrons from atom to atom ELECTRON FLOW CONDUCTOR - Materials which have
Chapter 19: DC Circuits
Chapter 19: DC Circuits EMF and Terminal Voltage Resistors in Series and in Parallel Kirchhoff s Rules EMFs in Series and in Parallel; Charging a Battery Capacitors in Series and in Parallel RC Circuits