IEC Separable Connectors 36 kv and 42 kv, 630A and 1250A Front T-Body / Coupling (Rear) T-Body Connector

Size: px

Start display at page:

Download "IEC Separable Connectors 36 kv and 42 kv, 630A and 1250A Front T-Body / Coupling (Rear) T-Body Connector"

Brent McKenzie
5 years ago
Views:

and fully submersible when mated with proper bushings or plugs. The products are used to terminate polymeric cable to dead front apparatus such as transformers, switchgear, and other equipment.

) with copper or aluminum conductors. The design is especially suited for the harsh off-shore or wind farm environment, where long runs and large cable sizes are needed.

1 IEC Separable Connectors 36 kv and 42 kv, 630A and 1250A Front T-Body / Coupling (Rear) T-Body Connector Application Chardon Front T-Body / Coupling (Rear) T-Body connectors are fully screened and fully submersible when mated with proper bushings or plugs. The products are used to terminate polymeric cable to dead front apparatus such as transformers, switchgear, and other equipment. They can be used for 36kV and 42 kv applications. The Chardon T-body connectors are suitable for indoor or outdoor applications, and are able to be used for all polymeric cable types ( XLPE, ETP, etc.) with copper or aluminum conductors. The design is especially suited for the harsh off-shore or wind farm environment, where long runs and large cable sizes are needed. Key Features Provides a fully shielded and submersible connection when mated with the proper bushing or plug. Type C 1250A interface. Mounting can be vertical, horizontal, or any angle in between. No minimum phase clearance requirements. 100% electrical tested in production. Product Ratings Maximum Voltage Class (U ): AC 5 Minute Withstand: DC 15 Minute Voltage Withstand: Minimum Corona Voltage Level: BIL and Full Wave Crest (Impulse): Thermal Short Circuit (Conductor, 3 sec.) Dynamic Short Circuit Continuous Current Production Tests Tests conducted in accordance with IEC Minimum Corona Voltage Level 45 kv 10pC AC 5 Minute Withstand 117 kv m 42 kv 117 kv 125 kv 45 kv < 10 pc 200 kv 45 ka 100 ka 1250 A 42FDT RDT REV12

2 Detailed composition of the Chardon 36 kv and 42 kv Front T-body Connector STUD Zinc plated, threaded steel stud 185mm (7.28") INSULATING PLUG Molded epoxy insulating plug provides excellent electrical, thermal and mechanical reliability. Ф101mm (3.98") 391mm (15.39") CONDUCTING INSERT conducting insert provides coronafree electrostatic shielding of the compression connector. INSULATION LAYER High quality peroxide cured EPDM insulation is mixed and formulated in-house for complete control of rubber characteristics. CONDUCTING SHIELD conducting shield provides ground shield continuity. CABLE ADAPTER Molded cable adapter, sized to fit the cable insulation, provides stress relief for the terminated cable. RUBBER END CAP Molded EPDM conducting rubber end cap protects and grounds the insulating plug test point. COMPRESSION CONNECTOR/ SHEAR BOLT CONNECTOR Compression connector / shear bolt connector made of aluminum, copper, or bimetal(aluminum/copper). DRAIN WIRE TAB Drain wire table provide a convenient point to connect drain wire to ensure grounding of the connector shield. Ф116mm (4.57")

3 Detailed composition of the Chardon 36 kv and 42 kv Coupling (Rear) T-body Connector 315mm (12.40") STUD Zinc plated, threaded steel stud CONTACT ROD Copper made contact rod provides a consistent current transfer path. INSULATING PLUG Molded epoxy insulating plug provides excellent electrical, thermal and mechanical reliability. Ф101mm (3.98") 391mm (15.39") Ф116mm (4.57") 129mm (5.08") RUBBER END CAP Molded EPDM conducting rubber end cap protects and grounds the insulating plug test point. CONDUCTING INSERT conducting insert provides coronafree electrostatic shielding of the compression connector. COMPRESSION CONNECTOR /SHEAR BOLT CONNECTOR Compression connector / shear bolt connector made of aluminum, copper, or bi-metal(aluminum/copper). INSULATION LAYER High quality peroxide cured EPDM insulation is mixed and formulated in-house for complete control of rubber characteristics. CONDUCTING SHIELD conducting shield provides ground shield continuity. DRAIN WIRE TAB Drain wire table provide a convenient point to connect drain wire to ensure grounding of the connector shield. CABLE ADAPTER Molded cable adapter, sized to fit the cable insulation, provides stress relief for the terminated cable.

4 ORDERING INFORMATION STEP 1 Code 42 - STEP 1 STEP 2 STEP 3 Selection of Front / Rear T-body FDT RDT STEP 2 Selection of Cable Insulation Dimension D E F G H J K L M N P Q R S T U V Front T-body Coupling(Rear)T-body ORDERING EXAMPLE: For a CHARDON 42 kv Front T-body with cable insulation outer dimension of 26.4 mm and a conductor size of 185 mm2 with copper compression connector, the part number would be as follows FDT 1250 E 185 C STEP 3 Selection of Conductor Size STEP 4 Code If a shear bolt connector is selected in this kit, the part number would be 42-FDT1250E-SBC-B-25-50/1 STEP FDT 1250 E SBC-B-25-50/1 Conductor Code Conductor Size(mm²) Selection of Compression Connector Material B Bi-metal ( Al & Cu ) C Copper

Chardon Shear Bolt Connector Example: ForaShear Bolt Connector with a conductor Range between 20-50 mm2, the

SBC-B-25-50/1 SBC-B-70-95/1 SBC-B-70-120/2 SBC-B-150-240/2 SBC-B-300-400/3 SBC-B-500-850/3 Conductor Range(mm2).

5 Chardon Shear Bolt Connector Example: ForaShear Bolt Connector with a conductor Range between mm2, the part number would be : SBC-B-25-50/1 CATALOG NO. SBC-B-25-50/1 SBC-B-70-95/1 SBC-B /2 SBC-B /2 SBC-B /3 SBC-B /3 Conductor Range(mm2) Chardon Taiwan Corporation No. 37 Min-Chie Road Tung Lo Industrial Park Miao Li, Taiwan 366 Phone: Fax:

IEC Separable Connectors 17.5 kv/24 kv, 630A

IEC Separable Connectors 17.5 kv/24 kv, 630A Front T-Body / Coupling (Rear) T-Body Connector Application The Chardon T-Body connectors are used to terminate polymeric cable to dead front apparatus such