Binding Finisher. Installation Procedure

Transcription

1 Binding Finisher MB-000C-NA MB-000C-EU Installation Procedure When installing this product, follow these instructions. (Make sure to perform the actual work with at least 2 people.) NOTE : THE FINISHER MUST BE INSTALLED BY A CUSTOMER SERVICE REPRESENTATIVE WHO HAS COMPLETED THE TRAINING COURSES ON THE BASE COPIER AND THE UNIT.

2 Read this first These Installation Procedure instructions use indications to help you safely perform installation. The meaning of each indication is explained below. About indications WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Emphasizes essential information.

3 Checking supplied items No. Equipment/Accessories No. Equipment/Accessories Warranty/Guarantee card (NA only) Ring opener 2 DFD docking bracket for upstream 2 Rebinding board 3 DFD docking bracket for down 3 Interface cable 4 Operation manual 4 Upper side cover 5 +Screw Lower side cover 6 Installation procedure 6 Slope 2 7 AC power cord 7 Finisher door cover 8 Cartridge label 8 Tapping screw 3x6 9 Cartridge 9 Spanner CD (Operation manual) Safety * NA only * This is already installed in the unit

4 Installation space The dimensions in the diagram below indicate the minimum amount of space that is necessary. 300mm or more (860mm) DOWN UP 900mm or more If this unit is the last downstream unit, leave the space indicated below open. 30mm or more UP 3

5 Directions for opening the cardboard box () Remove the cover of the cardboard box. Cut the plastic band and remove the cover of the cardboard box. (2) Remove the included items. Remove all of the included items. (3) Remove the side cover of the cardboard box, and then remove the upper cover of the cardboard box. Remove the side cover of the cardboard box. Remove the upper cover of the cardboard box (4) Remove the tape at the top of the plastic cover, and then open and pull down the plastic cover. 4

6 (5) Cut the tape at the bottom 4 corners of the cardboard box and open the corners. (6) Extend the length of the 4 casters at the bottom. Position after unboxing Use the supplied spanner to loosen the upper nut by rotating it clockwise. (View from the top) Extend the caster by rotating the lower nut clockwise. (7) Secure the casters into place. 00mm When the base of the product is 00 mm from the base of the cardboard box, secure the upper nut by rotating it anticlockwise. 5

7 (8) Remove the 2 pieces of cardboard packaging from the bottom center of the product. There two locations are at the front and back. (9) Remove the cardboard from the upper side. Remove the cardboard from the upstream side by cutting at the locations indicated with dotted lines. There are no dotted lines on the actual cardboard box. (0) Place the supplied slopes at the 2 locations on the upper side indicated in the illustration. Slope Align the edge of the slope with the position indicated by the arrow. 6

8 () Lower the product from the upper side. CAUTION Make sure to hold the product by the locations indicated with dotted lines. (2) Check that the heights of the entrance and exit are 860 mm from the floor. If the heights are not 860 mm, perform steps (6) and (7). 860mm Perform adjustments based on the floor of the installation area. 860mm 7

9 Directions for installing the Binding Finisher WARNING Check that all connected devices are turned OFF, and that the power plug is disconnected from the power outlet. () Remove the 2 brackets from the upstream side. (2) Remove the bracket from below the right door. Remove the 4 screws. Remove the 4 screws. Remove the 2 screws. (3) Remove the tape. (4) Open the right door, and remove the bracket from the bottom of the right door. Remove the 2 screws. 8

10 (5) Open the doors and remove the tape and cushion. A B Remove the binder unit. (A) Remove each piece of tape. Open the door and pull out the cartridge. (B) Remove the cushion inside. (6) Attach the Upper side cover to the upper side. Tighten the upper-right screw first. Tapping screw 3 6 9

11 (7) Attach the Lower side cover to the downstream side. Tighten the upper-right screw first. Tapping screw 3 6 (8) Open the supplied cardboard box. (9) Attach the DFD docking bracket for upstream to the bottom of the upper side. Base Insert this into the holes in the top. Hang it on the hooks. (3) () (4) (2) Secure these 4 locations with screws. screw 4 6 Tighten the screws in the order indicated above. 0

12 (0) Insert the Cartridge label into the cartridge.

13 If there are devices connected to the downstream unit side (refer to the installation manual of the downstream unit) () If using a DFD-specification downstream unit, attach the DFD docking bracket for down to the bottom of the downstream side. Base Insert this into the holes in the top. Hang it on the hooks. (2) (3) () Secure these 3 locations with screws. Tapping screw 4 6 (2) If using a Canon V-series FINISHER Align the unit embossment and the holes of the FINISHER Door Cover, and secure the 3 locations with screws. Align this with the holes in the embossment. Secure these 3 locations with screws. Tapping screw 3 6 2

14 Connecting the Binding Finisher to the upstream unit () Remove the screw from the DFD docking bracket. Remove the screw. Pull it forward. (2) Connect the unit to the upstream unit. (3) Lock the connector and secure it. Push the lever all the way inward. Secure it with a screw. 3

15 (4) From behind the unit, connect the power cord and the cable for the upstream unit. Connection with upstream unit Connection with downstream unit Secure these 2 locations with screws. Check that the ground fault breaker switch is set to the right position, and connect the power cord. Connect the power cord. CAUTION The soket-outlet shall be installed near the equipment and be easily accesible. Object/part No. Power Supply Cord (for EU) technical data Detachable SVT type, maximum 4.5 m long, minimum 25V, 0A. One end terminates in parallel-blade (NEMA 5-5P) attachment plug, other end in appliance coupler. 4

16 If there is any downstream finishing unit after the Max binder, it is imperative that you perform the following procedure. () Press the power switch to turn on the power and close the front door. Set this to the up position. (2) Press the left key when "Bind", "Bypass" or "Punch" is displayed in the operation panel's LCD. LCD (3) If "Pass Code?" is displayed, press the SET key, enter 5050 for the number area currently displayed as 0000 by using the arrow keys, and press the SET key. (4) Press the up and down arrow keys to select "Bypass Speed", and press the SET key. If the cursor is displayed in the number area, enter values based on the downstream unit by using the arrow keys, and press the SET key. (The unit of speed is mm/sec.) Adjust the bypass speed setting depend on the main printer device. Refer to LCD Display and Special operation in the service manual for more information on connectable devices and the value of the bypass speed. 5

17 (5)Press the up and down arrow keys to select Bypass Type? and press the SET key. (6) Press the up and down arrow keys to select Non-DFD and press the SET key. If this is set to any other selection you will get a message on the varioprint UI Check Max Binder (7) Press the ESC key 2 times, and check if "Bind", "Bypass" or "Punch" is displayed in the LCD to complete the procedure. CAUTION Input values by following the settings of the downstream unit. To update the software version, refer to the service manual. If the punch location and the ring location are not aligned, refer to the side register adjustment in the service manual. If the center of the upstream unit transfer and the center of the Binding Finisher transfer are unaligned, paper jams or binding problems may occur. Perform the following check and adjust the unaligned equipment. How to Check the Alignment () If the Binding Finisher is the unit fartherst downstream, go to (3). (2) Separate the unit on the downstream side and check from the downstream side of the Binding Finisher. (3) When using the Binding Finisher's "Bind" or "Punch" to print or bind, the paper should be visible as in the illustration below. (The mark for A4 size paper is on the left and the mark for LT size paper is on the right.) Center baseline LT size paper mark A4 size paper mark When using A4 paper, if the edge of the paper is off of the center baseline by two marks, as in the illustration below, the center of the transfer is off of the baseline by 4 mm, towards the back. Center baseline 6

18 How to Adjust the Alignment () Separate the upstream unit and the Binding Finisher. (See page 3.) (2) Remove screw from the DFD docking bracket and loosen screws 2, 3, and (3) Slide the DFD docking bracket to the back side and the front side, and align it with the center. (4) Tighten 3 screws (screw 2, 3, and 4), and see page 3 to connect the unit to the upstream unit As a screw will be leftover, be sure to keep it in storage. If the Binding Finisher is set up to eject finished documents to the right With some copiers, the Binding Finisher can be set up to eject finished documents to the right. This requires changes to parts and the control software. Documents ejected to the left Documents ejected to the right After changes 7

19 Comparison of specifications Document ejection direction Document ejection to left To left Document ejection to right To right Available modes Bypass Binding Punching Incoming sheet rate mm/s Internal feeding rate (Bypass) mm/s Internal feeding rate (Binding/Punching) mm/s Upstream unit Stacker Stacker Downstream unit None or finisher None Max. supported printing speed ppm Caution The Bypass mode cannot be used when the Binding Finisher is set up to eject finished documents to the right. 8

20 Parts for conversion to document ejection to the right Top transfer guide Bottom transfer guide Right side cover Docking bracket Parts to be changed out or added Part Right side cover Docking bracket Top transfer guide Bottom transfer guide Note Add because FB is farthest downstream unit Change because upstream unit is on other side Install because documents are transferred in opposite direction Install because documents are transferred in opposite direction Safety precaution The Finisher must be installed by a customer service representative who has completed the training courses on the base copier and the unit. 9

21 This instruction manual is subject to change without notice due to functional enhancement. N22G0000 PRINTED IN JAPAN