Carry out replacement in the following order:
|
|
- Oswin Blake
- 5 years ago
- Views:
Transcription
1 How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever. 3 Place wedge blocks under the rear wheels. Loosen the wheel mounting bolts. 4 5 Raise the front of the car and secure on supports. Remove the front wheels. 1 13
2 6 Unscrew the stabilizer link upper fastening Disconnect the fastener of the ABS sensor cable from the shock absorber strut. 8 Disconnect the brake hose holder from the shock absorber strut. 9 Disconnect the brake pads wear sensor. 2 13
3 10 Disconnect the ABS sensor. 12 Unscrew the lower fastener of the shock absorber strut. 11 Unscrew the ABS cable holder. 13 Unscrew the wheel hub axle nut Disconnect the steering knuckle from the shock absorber strut. 3 13
4 Open the hood Unscrew fixing bolts of the protective cover
5 Remove the upper seal from the firewall Remove the protective cover Unscrew the upper fastening of the shock absorber strut. 5 13
6 20 21 Set the shock absorber strut on the spring compressor tool. Remove the suspension strut. AutoDoc recommends: Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides. 22 Compress the spring. Ensure the correct position of the spring in the retainer. Make sure that the spring coils tightly entered the lock handles Remove the top mount, the support bearing and the upper spring cup. Unscrew the top fastening of the shock strut mount. 6 13
7 25 Remove the spring. 26 Remove the shock absorber dust cap and the bump stop. AutoDoc recommends: Τhoroughly examine the shock absorber mount, dust boot, bump stop. Replace them if necessary. Before installing a new shock absorber you should pump it manually 3-5 times Install the spring. Install a new shock absorber on a special fixture for further mounting of the spring 7 13
8 29 Install the dust sleeve and the bump stop on the new shock absorber Compress the spring Install the top mount, the strut mount bearing and the upper spring cup. Tighten the upper fastener of the shock absorber strut mount Install the shock strut into the wheel arch. 8 13
9 Tighten the shock strut top mount Install the protective cover Tighten fixing bolts of the protective cover. 9 13
10 Install the upper seal on the firewall Close the hood Install the steering knuckle onto the shock absorber strut. Tighten the lower fastening of the shock absorber
11 40 Tighten the ABS cable holder. 42 Connect the fastener of the ABS sensor cable to the shock absorber strut. 44 Connect the ABS sensor. 41 Fasten the brake hose on the strut. 43 Connect the brake pads wear sensor. 45 Tighten the stabilizer link upper fastening
12 46 Screw the wheel hub axle nut. 47 Install the wheel. 48 Lower the car and working in a cross order, tighten the wheel bolts Video tutorials Watch our detailed video guides about your VOLKSWAGEN TOURAN 1 repair on our youtube channel. Watch video guides. AutoDoc online We hope that this information have been useful for you! Highest quality shock absorbers for your car VOLKSWAGEN TOURAN 1 are available on AutoDoc. Go to the website
13 AUTODOC TOP QUALITY AND AFFORDABLE CAR PARTS ONLINE QUALITY AUTO PARTS VOLKSWAGEN SHOCK ABSORBERS SHOCK ABSORBERS FOR VOLKSWAGEN SHOCK ABSORBERS FOR Disclaimer: The document contains only general recommendations that may be useful for you when you perform repair or replacement works. AutoDoc shall not be liable for any loss, injury, damage of property, acquired in the repair or replacement process due to incorrect usage or misinterpretation of the provided information. AutoDoc shall not be liable for any possible mistakes and uncertainties in this guide. The information provided is for informative purposes only and cannot replace advice from specialists. AutoDoc shall not be liable for incorrect or hazardous usage of equipment, tools and car parts. AutoDoc strongly recommends to be careful and observe the safety rules when performing repair or replacement works. Remember: usage of low quality auto parts does not guarantee you the appropriate level of road safety. AUTODOC IN SOCIAL MEDIA Powered by TCPDF (
Carry out replacement in the following order:
How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever.
More informationCarry out replacement in the following order:
How to replace front suspension springs on Suzuki Swift 3 Carry out replacement in the following order: 1 Replace the springs on the Suzuki Swift 3 in pairs. 2 Tighten the parking brake lever. 3 Place
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever.
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on BMW 5 E60 Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car BMW 5 E60 at the same time. 2 Tighten
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever.
More informationCarry out replacement in the following order:
Carry out replacement in the following order: 1 Tighten the parking brake lever. 3 2 Place wedge blocks under the rear wheels. 4 Raise the front of the car and secure on supports. Loosen the wheel mounting
More informationCarry out replacement in the following order:
How to replace rear suspension shock absorbers on Honda CR-V III Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car Honda CR-V III at the same time.
More informationCarry out replacement in the following order:
How to replace the front hub bearing on NISSAN X-TRAIL T30 Carry out replacement in the following order: 1 Tighten the parking brake lever. 3 2 Place wedge blocks under the rear wheels. 4 Raise the front
More informationCarry out replacement in the following order:
How to replace the brake shoes of Carry out replacement in the following order: 1 Replace brake pads on Fiat Punto 188 in pairs for each axle. It ensures efficient braking Loosen the wheel mounting bolts.
More informationCarry out replacement in the following order:
How to replace the front brake Carry out replacement in the following order: 1 Perform the replacement of brake pads in complete set for each axis. This provides effective braking. Tighten the parking
More informationCarry out replacement in the following order:
How to replace the brake shoes of Carry out replacement in the following order: 1 Perform the replacement of brake pads in complete set for each axis. This provides effective braking. Do not wash the brake
More informationCarry out replacement in the following order:
How to replace the rear brake disc on NISSAN X-TRAIL T30 Carry out replacement in the following order: 1 Replace the brake disks on the car Nissan X-Trail T30 in complete set for each axis. Regardless
More informationCarry out replacement in the following order:
How to replace the rear brake disc on Honda CR-V III Carry out replacement in the following order: 1 Replace the brake disks on the car Honda CR-V III in complete set for each axis. Regardless of the state
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationM-FR3-FA Fiesta Handling Pack INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More informationPRODUCT NOTES: These components are designed for suspension height adjustment lower than stock height.
INSTALLATION INSTRUCTIONS Progress Technology Competition Series Coilover System 2001 2005 Acura RSX 2001-2005 Honda Civic, Civic Si Revision B (2/19/13) WHO SHOULD INSTALL THIS PRODUCT? Progress Technology
More information1998 Plymouth Breeze SUSPENSION' 'Rear - Cirrus, Stratus, Breeze & Sebring Convertible SUSPENSION
DESCRIPTION 1998-99 SUSPENSION Rear - Cirrus, Stratus, Breeze & Sebring Convertible Rear suspension uses a short/long arm independent design. See Fig. 1. Each side consists of a strut assembly, upper control
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION SPECIFICATIONS STRUT ASSEMBLY FRONT SUSPENSION DIAGNOSIS.
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 SPECIFICATIONS 33-3 FASTENER TIGHTENING SPECIFICATIONS 33-3 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 LUBRICANT 33-3 DIAGNOSIS
More informationSaab 9-3 CV M04-, 4D/5D M06-
SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part
More information1997 Mazda MX-5 Miata SUSPENSION Front - Miata
1997-2000 SUSPENSION Front - Miata DESCRIPTION NOTE: Mazda did not produce 1998 Miata models. Front suspension is an independent, double wishbone design using upper and lower control arms. A spring over
More informationWD Dodge Suspension Kit
92137600 02-05 2WD Dodge 1500 6 Suspension Kit Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these
More informationHow to Replace TOKICO Shocks
How to Replace TOKICO Shocks Aftermarket Division Hitachi Automotive Systems, Ltd. Contents Prohibited Actions! 1. How to Replace Shocks 2. Replace Suspension Strut 3. Replace Suspension Units
More information2004 Dodge Stratus ES. Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk. 1. Roll back carpeting on top of the rear shock tower
More information1994 Mazda MX-5 Miata. SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front
SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front DESCRIPTION An independent front suspension with MacPherson-type struts is used on all models. Miata uses double wishbone design upper and lower control
More informationGROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS... 33A-5
33A-1 GROUP 33A CONTENTS GENERAL DESCRIPTION 33A-2 DIAGNOSIS 33A-3 INTRODUCTION TO FRONT SUSPENSION DIAGNOSIS 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY 33A-3 SYMPTOM CHART 33A-3 SYMPTOM PROCEDURES 33A-3
More informationFRONT SUSPENSION GROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS...
33A-1 GROUP 33A FRONT SUSPENSION CONTENTS GENERAL DESCRIPTION......... 33A-2 DIAGNOSIS. 33A-3 INTRODUCTION TO DIAGNOSIS........................ 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 33A-3 SYMPTOM
More informationNOTICE TO DEALER AND VEHICLE OWNER
921751200 *1751BAG1* 1751BAG1 Thank you for choosing Rough Country for all your suspension needs. This kit will fit both 4WD and 2WD models, all brackets will be used for 4WD models. On 2WD models the
More informationA proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.
Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES
More informationAfter installation please observe the following points: Before installation please observe the following points:
Before installation please observe the following points: Read all information in this manual carefully. All suspension components are fitted and removed acc. to the manufacturer s specifications for installing
More informationFront Suspension - Front Stabilizer Bar Bushing Removal and Installation
1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Dodge Ram WD 6" Suspension Lift Kit
2012-2015 Dodge Ram 1500 4WD 6" Suspension Lift Kit PRE-INSTALLATION 35015 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
More informationARTICLE BEGINNING DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Rear. Golf III
Article Text ARTICLE BEGINNING 1995-96 SUSPENSION Rear Golf III DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake drums
More informationW205 C63 Suspension Adjustable Suspension Installation Guide
W205 C63 Suspension Adjustable Suspension Installation Guide 2015+ C63 AMG Sedan 2015+ C63S AMG Sedan Thank you for your purchase of the Weistec W205 C63 Adjustable Suspension. Please follow all directions,
More informationSECTION 2C FRONT SUSPENSION TABLE OF CONTENTS
SECTION 2C FRONT SUSPENSION TABLE OF CONTENTS Description and Operation... 2C-2 Front Suspension... 2C-2 Specifications... 2C-4 Component Locator... 2C-5 Front Suspension Assembly... 2C-5 Cross-Sectional
More informationPOS MR80 front. Shock absorber Kit for Porsche 986 and 987 Boxster/Cayman. Mounting Instructions
Kit Contents Description Part No Used on Pcs model 1 Sleeve 248-01 987 only 2 2 ABS cord bracket 219-01 98 and 987 2 Shock absorber POS R80 98 and 987 2 4 Dust boot 1021-01 98 and 987 2 Plastic spring
More informationINSTALLATION INSTRUCTIONS SOLO WERKS S1 Coilover Suspension BMW F22 /F30/F31/F32/F33/F34 Platform Part Number: S1BW010 / S1BW020 Rev.1.
Thank you for purchasing your new SOLO WERKS S1 Coilover suspension. IMPORTANT PLEASE READ BEFORE BEGINNING INSTALLATION: Please take a moment to review this installation process and verify that your kit
More information1. introduction 3 2. Wheel bearing special features 4 3. Wheel bearing units from an economical point of view 5
Motor chassis Service Technical BROCHuRE Wheel Bearing Repair Solutions for Light Commercial Vehicles CONTENT 1. introduction 3 2. Wheel bearing special features 4 3. Wheel bearing units from an economical
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION FASTENER TIGHTENING SPECIFICATIONS GENERAL SPECIFICATIONS...
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 FASTENER TIGHTENING SPECIFICATIONS 33-2 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 DIAGNOSIS 33-4 INTRODUCTION TO DIAGNOSIS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TY-530-N13 1. DESCRIPTION: NISMO SUSPENSION KIT 2. APPLICATION: 370Z 3. PART NUMBER: E3110-1EA00-US 4. KIT CONTENTS: Item No. Qty Service Part Number Description 1 1 E6110-1EA25
More information700 Pine Ridge Road Golden CO Tel (303) (888) 4X4 SLEE Fax (303)
700 Pine Ridge Road Golden CO 80403 Tel (303) 278 8287 1(888) 4X4 SLEE Fax (303) 278 7182 2005+ Toyota Tacoma OME Suspension Kit - Installation Instructions Qty Part Included Tools/ Materials Suggested
More informationTOYOTA FJ CRUISER 6 SUSPENSION KIT
92177000 TOYOTA FJ CRUISER 6 SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,
More information2012 Taurus Workshop Manual. DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011
SECTION 204-01: Front Suspension DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011 Strut and Spring Assembly Material Item Silicone Brake Caliper Grease and Dielectric Compound XG-3-A Specification
More informationINSTALLATION INSTRUCTION Rev A
INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationSuspension strut, removing and installing
Page 1 of 18 42-24 Suspension strut, removing and installing Removing Vehicle must be standing on its wheels above vehicle lift - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION ON-VEHICLE SERVICE FASTENER TIGHTENING SPECIFICATIONS...
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 FASTENER TIGHTENING SPECIFICATIONS 33-2 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 LUBRICANTS 33-3 DIAGNOSIS 33-4 INTRODUCTION
More informationFRONT SUSPENSION Click on the applicable bookmark to selected the required model year
FRONT SUSPENSION 33A-1 FRONT SUSPENSION CONTENTS GENERAL INFORMATION.................. 2 SERVICE SPECIFICATIONS................. 3 SPECIAL TOOLS........................... 3 ON-VEHICLE SERVICE.....................
More informationKJ to Current Jeep JK 3 lift with shocks
TOOLS NEEDED BILL OF MATERIALS Metric tools Floor jack Jack stand (s) 4 Wheel chocks Drill and 3/8 bit Other Jeep JK Products KJ09145BK Hood Wranglers KJ09144BK Tailgate Bumpstops KJ71020 Upper dash panel
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION REAR SUSPENSION DIAGNOSIS LOWER ARM AND TOE CONTROL ARM ASSEMBLY...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION........... 34-2 DIAGNOSIS.... 34-2 INTRODUCTION....................... 34-2 TROUBLESHOOTING STRATEGY........ 34-2 SYMPTOM CHART..................... 34-3 SYMPTOM
More information05-07 F /2 SUSPENSION KIT
92147900 05-07 F250 4 1/2 SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationFAG Wheel Bearing Repair Solution for Light Commercial Vehicles
FAG Wheel Bearing Repair Solution for Light Commercial Vehicles Mercedes-Benz Sprinter, Viano, Vito and Volkswagen Crafter Front Axle The content of this brochure shall not be legally binding and is for
More informationBMS MI40. Shock absorber Kit for BMW M3 (E90, E92) - front. Mounting Instructions
Kit Contents Description Pcs Strut Dust boot Nut M14 Spacer Mounted on shock absorber Sleeve 1 Used for front and rear C-spanner 1 C-spanner 1 Öhlins sticker 1 Öhlins Owner s Manual 1 Please note that
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM REAR SUSPENSION DIAGNOSIS TOE CONTROL ARM...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION 34-2 DIAGNOSIS 34-3 INTRODUCTION TO DIAGNOSIS 34-3 DIAGNOSTIC TROUBLESHOOTING STRATEGY 34-3 SYMPTOM CHART 34-3 SYMPTOM PROCEDURES 34-3 SPECIAL TOOLS 34-5 ON-VEHICLE
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationSCION xb LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-52080 Kit Contents Item # Quantity Reqd. Description 1 2 Front Springs 2 2 Rear Springs 3 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description 1 2 3
More informationSpring strut and spring front, replacing
"VCC128825 EN 20090329" 1(7) Spring strut and spring front, replacing Special tools: 951 2911, 951 2914, 951 2915, 951 2564, 999 5500, 999 5576, 999 5758 Removing the spring strut Note! From model year
More informationREAR SUSPENSION 34-1 CONTENTS GENERAL INFORMATION... 2 UPPER ARM ASSEMBLY... 8 SERVICE SPECIFICATIONS... 3 TRAILING ARM ASSEMBLY...
4-1 REAR SUSPENSION CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... SPECIAL TOOLS... ON-VEHICLE SERVICE... 4 Wheel Alignment Check and Adjustment... 4 Ball Joint Dust Cover Check... 5 REAR
More informationFRONT SHOCK ABSORBER
FRONT SHOCK ABSORBER INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a MAZDASPEED accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationCOBB SPORT SPRINGS
913760 - COBB SPORT SPRINGS 2004-2007 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2004-2007 Subaru WRX/STi. The following instructions will assist you through your
More informationFRONT SUSPENSION LOCATION INDEX
1. Remove the front suspension tower bar. (See FRONT SUSPENSION TOWER BAR REMOVAL/INSTALLATION.) 2007 Mazda MX-5 Miata Sport 2007 SUSPENSION Front Suspension - MX-5 Miata FRONT SUSPENSION LOCATION INDEX
More informationSUS MI10 front front. Shock Absorber Kit for Subaru Impreza (GRB)
Before installing this product, check the contents of the kit. If anything is missing, please contact an Öhlins dealer. Kit Contents Shock absorber Upper spring seat Dust boot Top mount Bearing spacer
More informationTOYOTA COROLLA LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description
More informationREAR SUSPENSION GROUP CONTENTS GENERAL INFORMATION FASTENER TIGHTENING SPECIFICATIONS TRAILING ARM...
34-1 GROUP 34 CONTENTS GENERAL INFORMATION 34-2 FASTENER TIGHTENING SPECIFICATIONS 34-4 GENERAL SPECIFICATIONS 34-4 SERVICE SPECIFICATIONS 34-5 LUBRICANTS 34-5 DIAGNOSIS 34-6 INTRODUCTION TO DIAGNOSIS
More informationPOZ MR80 front. Shock absorber Kit for Porsche 987 Boxster/Cayman. Mounting Instructions
Kit Contents Description Part No Pcs 1 Sleeve ABS cord bracket 519-01 Shock absorber POS 5P80 4 Dust boot 101-01 5 Plastic spring spacer 50-01 Spring Rubber spring spacer 501-01 8 Lock nut M14 4-04 9 C-spanner
More informationINSTALLATION INSTRUCTIONS Mopar Performance 2 Lift System 2009 and Newer Dodge Ram 1500 (DS) 4WD PART NUMBER P
INTRODUCTION Installation requires a professional mechanic. Prior to beginning, inspect the vehicle s steering, driveline, and brake systems, paying close attention to the suspension link arms and bushings,
More information02-10 GM 2500HD / HD & HD CLASSIC 6 2WD SUSPENSION KIT
92122000 92127400 02-10 GM 2500HD / 01-06 1500HD & 07 1500HD CLASSIC 6 2WD SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM ASSEMBLY REAR SUSPENSION DIAGNOSIS
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION......... 34-2 DIAGNOSIS.. 34-3 INTRODUCTION TO DIAGNOSIS........................ 34-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 34-3 SYMPTOM CHART...................
More informationFRONT SUSPENSION REMOVAL
FRONT SUSPENSION REMOVAL 1. Raise the vehicle off the ground and firmly support it with safety stands, then, remove the front and rear tires. NOTE: Do not work on or underneath the car without the proper
More information97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT
921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long
More informationFront and Rear Suspension Modification Kit Installation
Page 1 of 12 2014 Chevrolet Sonic (US/Canada) Sonic US/Canada Accessory Installation Manual Accessories Performance Accessories Accessories Document ID: 3471343 Front and Rear Suspension Modification Kit
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS STEP 1: Park vehicle on level surface and chock rear wheels.
2007-2013 7.5" GMC/Chevrolet 1500 4WD Suspension Lift kit PRE-INSTALLATION 15004 2 - Cross-member (Fr/Rr) 2 - Sway Bar Drop Bracket 2 - Knuckle (Dr/Pass) 1 - Driver Diff. Bracket 1 - Passenger Diff. Bracket
More informationEibach Pro-Damper Shocks & Struts (05-09 All):
Eibach Pro-Damper Shocks & Struts (05-09 All): Required tools: 3/8 and 1/2 drive ratchets 7, 8, 10, 15, 16, 17, 18, 21 & 22 mm open ended wrenches 8 & 10 mm box end wrenches 10mm socket 13, 15 & 18 mm
More informationINSTALLATION INSTRUCTION 88581
INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension
More informationFRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
More information2011 F SUSPENSION KIT
92156300 Thank you for choosing Rough Country for your suspension needs. 2011 F250 4.5 SUSPENSION KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationTOYOTA PRIUS PLUS LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-47100 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Nut 4 1 Instructions Hardware Bag Contents Item # Quantity Reqd. Description 1 2
More informationWeistec True Downpipes
Weistec True Downpipes Installation Guide, W212, W218, AWD 2014+ E63 2014+ CLS63 WARNING! IF YOU ARE NOT EXPERIENCED IN THE AREA OF AUTOMOTIVE MECHANICS, WE STRONGLY URGE THAT YOU REFER THIS INSTALLATION
More informationBMW M2, M3, M4 (F87, F80, F82)
Kit Contents Description Part No Pcs Spacer 2429-5 2 2. Shock absorber BMS R40 2.2 Shock absorber BMS 2R40 Dust boot 02-0 2 4 Plastic spring spacer 2502-0 2 5 Spring 2 Rubber spring spacer 250-0 2 Upper
More informationSuspension strut, removing and installing
Page 1 of 16 40-39 Suspension strut, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove wheels. - Remove rubber grommets
More informationA/F/X Body GM Installation Instructions Manual Disc Conversion
A/F/X Body GM Installation Instructions Manual Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body DBMC09 & PVK71 pictured above (Booster, master & valve setups may vary by upgrades selected) Your
More informationTechnical Service BULLETIN
Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationSee SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )
Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls
More informationWarning! READ BEFORE INSTALLING. Notice to Owner, Operator, Dealer and Installer
Warning! READ BEFORE INSTALLING Notice to Owner, Operator, Dealer and Installer ReadyLIFT Off Road Suspension s Mid Travel and Long Travel suspension systems and components are designed for OFF ROAD USE
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More information1998 Buick Century Limited
STABILIZER SHAFT LINK Removal 1. Raise and support the vehicle. 2. Disconnect the rear stabilizer shaft link from the strut. 3. Remove the rear stabilizer shaft link nut. 4. Remove the stabilizer shaft
More informationInstallation Guide for the JK Wrangler 4-Inch Suspension System with FlexArms
INSTALLATION GUIDE Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.713.2313 www.teraflex.biz Installation Guide for the JK Wrangler 4-Inch Suspension System
More informationPage 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).
More informationBMS MP40. Shock absorber Kit for BMW M3/M4 (F80/F82) - front. Mounting Instructions
Pos nr Description Part nr Qty 1 Spacer 469-15.1 Shock absorber BMS 1P40 (L) 1. Shock absorber BMS P40 (R) 1 Dust boot 1016-01 4 Spring 5 Upper spring seat 5618-10 6 Spacer Washer 469-15 8 Lock nut M1
More informationSA 8 FRONT AXLE HUB COMPONENTS
SA8 FRONT AXLE HUB COMPONENTS SA9 REMOVAL OF FRONT AXLE HUB 1. REMOVE COTTER PIN, LOCK NUT CAP AND BEARING LOCK NUT (a) Remove the cotter pin and lock nut cap. (b) Loosen the bearing lock nut while depressing
More informationE4-WM5-Y530A00 MOUNTING INSTRUCTION
IMPORTANT! READ THIS FIRST! Installation of shock absorbers requires special tools and expert knowledge. Accordingly, installation of all BILSTEIN products must be performed by a qualified suspension specialist.
More informationDetroit Speed, Inc. Caster/Camber Plate Kit Camaro/Firebird P/N:
Detroit Speed, Inc. Caster/Camber Plate Kit 1982-92 Camaro/Firebird P/N: 030330 The Detroit Speed Inc., Caster/Camber Plate Kit is a direct bolt-on kit that allows precise camber and caster adjustments
More informationE4-WM5-Y556A00 MOUNTING INSTRUCTION
IMPORTANT! READ THIS FIRST! Installation of shock absorbers requires special tools and expert knowledge. Accordingly, installation of all BILSTEIN products must be performed by a qualified suspension specialist.
More informationCOBB SPORT SPRINGS
915760 - COBB SPORT SPRINGS 2008-2013 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2008-2013 Subaru WRX/STi. The following instructions will assist you through your
More informationDate No ST Suspensions is a brand of KW automotive North America, Inc. - KW automotive North America, Inc.
No. 14430010 - ST Suspensions is a brand of KW automotive North merica, Inc. - KW automotive North merica, Inc. - Page 1 INSTLLTION INSTRUCTIONS Before you start to install, please read the following instructions
More information2011 F250 6 SUSPENSION KIT
92156500 Thank you for choosing Rough Country for your suspension needs. 2011 F250 6 SUSPENSION KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationBMS MP40. Shock absorber Kit for BMW M3/M4 (F80/F82) - front. Mounting Instructions
Pos nr Description Part nr Qty Spacer 24629-5 2 2. Shock absorber BMS P40 (L) 2.2 Shock absorber BMS 2P40 (R) Dust boot 026-0 2 4 Spring 2 5 Upper spring seat 2568-0 2 6 Spacer 24629-2 Washer 2469-0 2
More informationCOBB WRX Sports Springs West 1820 South Salt Lake City, UT USA (801)
COBB 3362 West 1820 South Salt Lake City, UT 84104 USA (801) 713-0035 2008 WRX Sports Springs Congratulations on your purchase of the COBB Sports Springs. The following instructions should assist you through
More information1993 SUSPENSION Volkswagen Rear. EuroVan
Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Rear EuroVan DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake
More information07-UP AVALANCHE 7.5 KIT
92120900R1 07-UP AVALANCHE 7.5 KIT Thank you for choosing Rough Country for your suspension needs. We appreciate your business!! This kit will not fit vehicles equipped with electric steering or trucks
More information