Carry out replacement in the following order:
|
|
- Piers Reynolds
- 5 years ago
- Views:
Transcription
1 How to replace the front hub bearing on NISSAN X-TRAIL T30 Carry out replacement in the following order: 1 Tighten the parking brake lever. 3 2 Place wedge blocks under the rear wheels. 4 Raise the front of the car and secure on supports. Loosen the wheel mounting bolts. 5 Remove the front wheels. 6.1 Unscrew the brake caliper fastening 1 10
2 6.2 7 Remove the brake caliper. 8.1 AutoDoc recommends: Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system. Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Remove the brake disc Unscrew the end fastening nut to the steering knuckle. 2 10
3 Using a special tool push the steering rod end out of the steering knuckle. 11 Remove the ABS sensor from the steering knuckle Unscrew the wheel hub fastening nut 14 Remove the ball joint from the steering knuckle. Unscrew the ball joint fastening nut. 3 10
4 Unscrew the lower fastener of the shock absorber strut. 16 Remove the drive shaft from the wheel hub. 18 Press the wheel hub out from the tapered roller bearing. 17 Remove the steering knuckle together with the hub Remove the retaining rings. 4 10
5 Press out the wheel hub bearing AutoDoc recommends: Clear the components and apply a thin layer of grease on the bearing seat Install the external retaining ring. 5 10
6 Press the new bearing in the steering knuckle Install the retaining ring in the steering knuckle Install the wheel hub on the steering knuckle. 6 10
7 25 26 Install the drive shaft into the wheel hub. Install the steering knuckle with a hub in assembly Tighten the lower fastening of the shock absorber. 28 Connect the ball joint to the steering knuckle. Tighten the ball joint fastener. 29 Screw the hub nut. 7 10
8 Install the ABS sensor on the steering knuckle and secure it Connect the tie rod end to the steering knuckle and tighten it. 32 Install a new brake disc on the hub Install the brake caliper and fix it. 8 10
9 Install the wheel. Lower the car and working in a cross order, tighten the wheel bolts. Video tutorials Watch our detailed video guides about your NISSAN X-TRAIL T30 repair on our youtube channel. Watch video guides. AutoDoc online We hope that this information have been useful for you! Highest quality wheel/hub bearing kits for your car NISSAN X-TRAIL T30 are available on AutoDoc. Go to the website. 9 10
10 AUTODOC TOP QUALITY AND AFFORDABLE CAR PARTS ONLINE QUALITY AUTO PARTS NISSAN WHEEL/HUB BEARING KITS NISSAN X-TRAIL T30 WHEEL/HUB BEARING KITS FOR NISSAN WHEEL/HUB BEARING KITS FOR NISSAN X-TRAIL T30 Disclaimer: The document contains only general recommendations that may be useful for you when you perform repair or replacement works. AutoDoc shall not be liable for any loss, injury, damage of property, acquired in the repair or replacement process due to incorrect usage or misinterpretation of the provided information. AutoDoc shall not be liable for any possible mistakes and uncertainties in this guide. The information provided is for informative purposes only and cannot replace advice from specialists. AutoDoc shall not be liable for incorrect or hazardous usage of equipment, tools and car parts. AutoDoc strongly recommends to be careful and observe the safety rules when performing repair or replacement works. Remember: usage of low quality auto parts does not guarantee you the appropriate level of road safety. AUTODOC IN SOCIAL MEDIA Powered by TCPDF (
Carry out replacement in the following order:
Carry out replacement in the following order: 1 Tighten the parking brake lever. 3 2 Place wedge blocks under the rear wheels. 4 Raise the front of the car and secure on supports. Loosen the wheel mounting
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever.
More informationCarry out replacement in the following order:
How to replace the rear brake disc on NISSAN X-TRAIL T30 Carry out replacement in the following order: 1 Replace the brake disks on the car Nissan X-Trail T30 in complete set for each axis. Regardless
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever.
More informationCarry out replacement in the following order:
How to replace the rear brake disc on Honda CR-V III Carry out replacement in the following order: 1 Replace the brake disks on the car Honda CR-V III in complete set for each axis. Regardless of the state
More informationCarry out replacement in the following order:
How to replace the brake shoes of Carry out replacement in the following order: 1 Perform the replacement of brake pads in complete set for each axis. This provides effective braking. Do not wash the brake
More informationCarry out replacement in the following order:
How to replace the front brake Carry out replacement in the following order: 1 Perform the replacement of brake pads in complete set for each axis. This provides effective braking. Tighten the parking
More informationCarry out replacement in the following order:
How to replace front suspension springs on Suzuki Swift 3 Carry out replacement in the following order: 1 Replace the springs on the Suzuki Swift 3 in pairs. 2 Tighten the parking brake lever. 3 Place
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever.
More informationCarry out replacement in the following order:
How to replace the brake shoes of Carry out replacement in the following order: 1 Replace brake pads on Fiat Punto 188 in pairs for each axle. It ensures efficient braking Loosen the wheel mounting bolts.
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on BMW 5 E60 Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car BMW 5 E60 at the same time. 2 Tighten
More informationCarry out replacement in the following order:
How to replace front suspension shock absorbers on Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car at the same time. 2 Tighten the parking brake lever.
More informationCarry out replacement in the following order:
How to replace rear suspension shock absorbers on Honda CR-V III Carry out replacement in the following order: 1 Replace both shock absorbers at the repair of your car Honda CR-V III at the same time.
More information2003 Ford Focus ZTW SUSPENSION Front - Focus
HUB/STEERING KNUCKLE ASSEMBLY Removal 1. Loosen the strut tower nuts by at least five turns. See Fig. 4. Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper
More informationSee SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )
Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More informationSA 8 FRONT AXLE HUB COMPONENTS
SA8 FRONT AXLE HUB COMPONENTS SA9 REMOVAL OF FRONT AXLE HUB 1. REMOVE COTTER PIN, LOCK NUT CAP AND BEARING LOCK NUT (a) Remove the cotter pin and lock nut cap. (b) Loosen the bearing lock nut while depressing
More informationREPLACEMENT 1. REMOVE FRONT WHEEL
3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake
More informationWheel bearings, assembly overview
Volkswagen Passat B6 - Wheel bearings, assembly overview Стр 1 из 9 40-5 Wheel bearings, assembly overview Suspension strut Multi-point socket head bolt Tip of bolt must point in direction of travel Left
More informationSUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20
SUSPENSION - FRONT 1992 Infiniti G20 1991-92 SUSPENSION Front G20 DESCRIPTION G20 uses a 4-wheel independent multi-link suspension system. Transverse links are connected to bottom of steering knuckle.
More informationPage 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).
More information2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.
4-2 [W2A1] SERVICE PROCEDURE 9) Install tie-rod end ball joint on housing knuckle arm. 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.8 (1) Cotter pin (2) Castle nut (3) Tie-rod B4M2214B 10) While depressing brake
More information2000 Honda Accord EX
HUB & KNUCKLE ASSEMBLY Removal (Except Odyssey & S2000) 1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION REAR SUSPENSION DIAGNOSIS LOWER ARM AND TOE CONTROL ARM ASSEMBLY...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION........... 34-2 DIAGNOSIS.... 34-2 INTRODUCTION....................... 34-2 TROUBLESHOOTING STRATEGY........ 34-2 SYMPTOM CHART..................... 34-3 SYMPTOM
More informationReplace brake pads and discs - front * (Volkswagen Sharan 2010-Present)
Replace brake pads and discs - front * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions,
More informationSUSPENSION. Front - Corvette
1998-99 SUSPENSION Front - Corvette DESCRIPTION The major suspension components are made of high-strength, lightweight, forged aluminum alloy. A fiberglass single-leaf spring is mounted transversely below
More information1. introduction 3 2. Wheel bearing special features 4 3. Wheel bearing units from an economical point of view 5
Motor chassis Service Technical BROCHuRE Wheel Bearing Repair Solutions for Light Commercial Vehicles CONTENT 1. introduction 3 2. Wheel bearing special features 4 3. Wheel bearing units from an economical
More information1997 Mazda MX-5 Miata SUSPENSION Front - Miata
1997-2000 SUSPENSION Front - Miata DESCRIPTION NOTE: Mazda did not produce 1998 Miata models. Front suspension is an independent, double wishbone design using upper and lower control arms. A spring over
More informationJOINT SHAFT REMOVAL/INSTALLATION
2001 MPV 2001 - MPV - Workshop Manual - Driveline/Axle JOINT SHAFT REMOVAL/INSTALLATION Report a problem with this article Performing the following procedures without first removing the ABS wheel speed
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationFAG Wheel Bearing Repair Solution for Light Commercial Vehicles
FAG Wheel Bearing Repair Solution for Light Commercial Vehicles Mercedes-Benz Sprinter, Viano, Vito and Volkswagen Crafter Front Axle The content of this brochure shall not be legally binding and is for
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM ASSEMBLY REAR SUSPENSION DIAGNOSIS
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION......... 34-2 DIAGNOSIS.. 34-3 INTRODUCTION TO DIAGNOSIS........................ 34-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 34-3 SYMPTOM CHART...................
More informationFRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
More information3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17
FRONT AXLE DRIVE SHAFT SYSTEM 3. Front Axle A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. 6) Remove the disc rotor from hub. If the disc rotor seizes up within
More information1994 Mazda MX-5 Miata. SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front
SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front DESCRIPTION An independent front suspension with MacPherson-type struts is used on all models. Miata uses double wishbone design upper and lower control
More informationRaptor "Race 1.5" Upper Control Arm Kit! Installation Guide! Rev 1B! Sales: ext 1! Tech Support: ext 2! Vista Grande!
Raptor "Race 1.5" Upper Control Arm Kit Installation Guide Rev 1B Sales: 866-691-7750 ext 1 Tech Support: 866-691-7750 ext 2 23231 Vista Grande Laguna Hills, CA 92653 Install Videos: YouTube "Raptor Performance
More informationFRONT SUSPENSION LOCATION INDEX
1. Remove the front suspension tower bar. (See FRONT SUSPENSION TOWER BAR REMOVAL/INSTALLATION.) 2007 Mazda MX-5 Miata Sport 2007 SUSPENSION Front Suspension - MX-5 Miata FRONT SUSPENSION LOCATION INDEX
More information1. General Description
General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Propeller shaft type 3UJ Front propeller shaft Joint-to-joint length: L 1 mm (in) 633 (24.92) Rear propeller shaft Joint-to-Joint
More informationREPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED
Page 1 of 13 2007 GMC Yukon 5.3L Eng Base Service Manual: FRONT SUSPENSION SYSTEM Print Date: REPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED J 43631 Ball Joint Separator.
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM REAR SUSPENSION DIAGNOSIS TOE CONTROL ARM...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION 34-2 DIAGNOSIS 34-3 INTRODUCTION TO DIAGNOSIS 34-3 DIAGNOSTIC TROUBLESHOOTING STRATEGY 34-3 SYMPTOM CHART 34-3 SYMPTOM PROCEDURES 34-3 SPECIAL TOOLS 34-5 ON-VEHICLE
More informationFront brakes, servicing
Page 1 / 12 46-1 Front brakes, servicing Front brakes - brake caliper Girling, servicing Note : After replacing brake pads, depress brake pedal several times firmly to properly seat brake pads in their
More informationR Assembly/disassembly recommendations
R159.44 Assembly/disassembly recommendations CITROËN: PEUGEOT: Berlingo, C3 (I and II), C5, C5 FL, C4, C4 B7, C3 Picasso, C4 Picasso, DS3, DS4, DS5, 307, 307 Restyling, Partner, 207, 308, 3008, 5008, RCZ,
More information1. General Description
General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Model All models Propeller shaft type EDJ Front propeller shaft Joint-to-joint length: L 1 mm (in) AT 735.5 (28.96) MT 675.5
More information2012 MKT Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011
SECTION 205-05: Rear Drive Halfshafts REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011 Halfshaft Special Tool(s) Axle Seal Protector 205-816 Front Hub Remover 205-D070 (D93P-1175-B) or equivalent
More informationWheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles
Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical
More informationkit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions
InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950
More informationFront Hub and Disc (4WD Model)
4C 8 DRIVE SHAFT SYSTEM Disassembled View Front Hub and Disc (4WD Model) 411RW001 Legend (1) Bolt (2) Cap (3) Snap Ring and Shim (4) Hub Flange (5) Lock Washer and Lock Screw (6) Hub Nut (7) Outer Bearing
More informationREAR AXLE GROUP CONTENTS GENERAL DESCRIPTION REAR AXLE DIAGNOSIS REAR AXLE HUB ASSEMBLY KNUCKLE...
27-1 GROUP 27 CONTENTS GENERAL DESCRIPTION......... 27-2 DIAGNOSIS......... 27-2 INTRODUCTION TO DIAGNOSIS........................ 27-2 DIAGNOSTIC TROUBLESHOOTING STRATEGY...... 27-2 SYMPTOM CHART...................
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R1 REAR DRUM TO DISC BRAKE CONVERSION KIT A130-3 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your
More informationSaab 9-3 CV M04-, 4D/5D M06-
SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part
More informationDura Force Disc Brake System Service Manual
TS 20809_a 3501 Shotwell Drive ISO/TS 16949:2002 Registered (PH): 937.743.8125 Franklin, OH 45005 www.waltheremc.com (FX): 937.743.8232 Table of Contents General Description 1 3 Fastener Torque Chart 4
More informationIf it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
More informationA proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.
Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More information4. Rear Axle REAR AXLE
REAR AXLE DRIVE SHAFT SYSTEM 4. Rear Axle A: REMOVAL 1) Disconnect the ground cable from battery. 2) Lift-up the vehicle, and remove the rear wheel. 3) Unlock the axle nut. 4) Remove the axle nut using
More informationALLDATA Online Dodge Truck Caravan V L - Front. Front
Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle
More informationFRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2
FRONT & REAR AXLE SECTIONAX CONTENTS FRONT AXLE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH) Troubleshooting...3
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationPRE-INSTALLATION Ford F150 4WD 4" Suspension Lift Kit
2009-2013 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 25007 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
More informationTABLE OF CONTENTS 0. Section 08 SUSPENSION Subsection 01 (TABLE OF CONTENTS)
Subsection 0 (TABLE OF CONTENTS) TABLE OF CONTENTS 0 FRONT SUSPENSION... 08-02- GENERAL... 08-02-2 STRUT-TYPE FRONT SUSPENSION... 08-02-2 LOWER SUSPENSION ARM PROTECTOR... 08-02-3 LOWER SUSPENSION ARM...
More information1. Set the position of the hub to FREE and remove the six hex-drive bolts.
1. Raise vehicle on a hoist, remove road wheels, disconnect the drag-link from the passenger-side hub assembly and disconnect the steering tie rod ends from both the driver and passenger side hub assemblies.
More informationReplace front brake pads and discs * (Ford Galaxy )
Replace front brake pads and discs * (Ford Galaxy 2006-2015) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if you're
More informationFRONT GENERAL A X L E
GENERAL General diagram of braking circuits 30 FRONT AXLE GENERAL Tightening torques (in dan.m) 30 FRONT AXLE GENERAL Tightening torques (in dan.m) 30 REAR AXLE GENERAL Tightening torques (in dan.m) 30
More informationINSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT
INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-4 FULL FLOATING AXLE OR A130-5 (1 PIECE AXLE) Thank you
More informationTechnician Handbook. 453 Suspension, Steering and Handling. Technician Objectives
Technician Objectives 1. List the six functions of suspension components.. 2. List the six major groups of components that require inspection. 3. Explain the inspection methods for the individual suspension
More information1998 Plymouth Breeze SUSPENSION' 'Rear - Cirrus, Stratus, Breeze & Sebring Convertible SUSPENSION
DESCRIPTION 1998-99 SUSPENSION Rear - Cirrus, Stratus, Breeze & Sebring Convertible Rear suspension uses a short/long arm independent design. See Fig. 1. Each side consists of a strut assembly, upper control
More informationTechnical Service BULLETIN
Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS STEP 1: Park vehicle on level surface and chock rear wheels.
2007-2013 7.5" GMC/Chevrolet 1500 4WD Suspension Lift kit PRE-INSTALLATION 15004 2 - Cross-member (Fr/Rr) 2 - Sway Bar Drop Bracket 2 - Knuckle (Dr/Pass) 1 - Driver Diff. Bracket 1 - Passenger Diff. Bracket
More information2012 Taurus Workshop Manual. DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011
SECTION 204-01: Front Suspension DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011 Strut and Spring Assembly Material Item Silicone Brake Caliper Grease and Dielectric Compound XG-3-A Specification
More information2004 Explorer/Mountaineer Workshop Manual
Page 1 of 6 SECTION 204-00: Suspension System 2004 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/05/2005 Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm
More information1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2
1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels
More information1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:
1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,
More information2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement
2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement Exploded View Special Tools Required Ball joint thread protector, 14 mm 071AF-S3VA000 Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool,
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL
More informationIncorrect Torque Specification Front & Rear Brake Caliper Retaining Bolts & Guide Pins
SERVICE XK8 DATE 2/97 TECHNICAL BULLETIN Incorrect Torque Specification Front & Rear Brake Caliper Retaining Bolts & Guide Pins MODEL VIN 206-03 1997 MY-ON XK8 Range 001001-ON Issue: The torque specifications
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS 1. Raise and support front of vehicle. Remove wheels. Remove caliper bolt and brakeline bracket bolts. Pivot caliper aside. Remove pads and pad shim. Remove
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W120-22, W120-23 1964 1/2-69 MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More information09-UP FORD F150 6 LIFT KIT
92159800 09-UP FORD F150 6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions,
More informationTitle: FRONT BRAKE VIBRATION Models: Tundra. Front Brake Caliper & Rotor Replacement (2WD, Both Sides)
Technical Service BULLETIN September 16, 2002 Title: FRONT BRAKE VIBRATION Models: 00-03 Tundra BR004-02 BRAKES TSB REVISION NOTICE: S March 5, 2004: A torque speification on page 10, step 24, was changed.
More informationSUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE
SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension
More informationSpring strut and spring front, replacing
"VCC128825 EN 20090329" 1(7) Spring strut and spring front, replacing Special tools: 951 2911, 951 2914, 951 2915, 951 2564, 999 5500, 999 5576, 999 5758 Removing the spring strut Note! From model year
More informationHow to Replace TOKICO Shocks
How to Replace TOKICO Shocks Aftermarket Division Hitachi Automotive Systems, Ltd. Contents Prohibited Actions! 1. How to Replace Shocks 2. Replace Suspension Strut 3. Replace Suspension Units
More informationBRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
More informationRaptor Tie Rods Kit Installation Guide Rev X2
Raptor Tie Rods Kit Installation Guide Rev X2 Sales: 949-212-7911 Tech Support: 949-444-3213 Install Videos: YouTube "Raptor Performance Group" COMPLETELY READ INSTALLATION INSTRUCTIONS PRIOR TO INSTALLING
More informationREAR HUB UNIT BEARING
2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL
More informationM-FR3-FA Fiesta Handling Pack INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationTorque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC
Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing
More informationHow it s done Fitting instructions for replacing brakes
How it s done Fitting instructions for replacing brakes Fitting instructions for replacing brakes We invest a lot in developing our products. We complete up to 300,000 test kilometres and 1,000 hours of
More informationFRONT SUSPENSION SYSTEM
SYSTEM PROBLEM SYMPTOMS TABLE SYSTEM Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary,
More informationFRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX
D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precautions... 2 PREPARATION...
More information1. Set the position of the hub to FREE and remove the six hex-drive bolts.
1. Raise vehicle on a hoist, remove road wheels, disconnect the drag-link from the passenger-side hub assembly and disconnect the steering tie rod ends from both the driver and passenger side hub assemblies.
More information1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
More informationTrailMaster TAURUS 400UTV
TrailMaster TAURUS 400UTV Set up instruction Version:.0 0/09/6 This set up instruction guides our customer to set up the go kart TrailMaster TAURUS 400UTV step by step to ensure a correct assembly for
More informationChapter. Steering System Technology. Basic Steering Systems. Functions of a Steering System. Basic Steering Systems
78 Chapter Steering System Technology Name _ Instructor Date _ Score Objective: After studying this chapter, you will be able to summarize the construction and operation of steering systems. Basic Steering
More informationFront Suspension - Front Stabilizer Bar Bushing Removal and Installation
1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support
More informationLower Arm ( ) Special Service Tools. Removal.
Page 1 of 6 (60.35.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
More informationMAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714 630 0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: PARTS LIST K751364 6" LIFT KIT 07 12 GM 1500 PICKUP QTY SPINDLE, CHEVY
More informationFRONT DROP SPINDLES
92725000 88-98 2 FRONT DROP SPINDLES Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More information