See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )

Size: px
Start display at page:

Download "See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )"

Transcription

1 Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls roll. ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES NOTE: See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. BALL JOINT CHECKING 4. Inspect ball joints for wear. Raise and support front of vehicle. Allow suspension to hang freely. Set front wheels to straight-ahead position. Press brake pedal. Remove front wheel and install hub nuts to disc. Measure upper lower ball joint vertical play. Replace ball joint if vertical movement exceeds 0.020" (.50 mm). Measure rotating torque of ball joint with joint removed from vehicle. Flip joint stud back and forth 5 times. Install ball joint stud nut. Using INCH-lbs. torque wrench, rotate ball joint stud continuously one revolution per 2-4 seconds while measuring rotating torque. Replace ball joint if rotating torque exceeds specification. See BALL JOINT ROTATING TORQUE SPECIFICATIONS table. BALL JOINT ROTATING TORQUE SPECIFICATIONS Application INCH Lbs. (N.m) Lower Ball Joint 1-22 (.10-5) Upper Ball Joint 6-39 ( ) RIDING HEIGHT Riding height will differ, depending on model and vehicle tire size. Loaded and unloaded vehicle ride heights are adjusted for individual vehicles. See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. REMOVAL & INSTALLATION BALL JOINTS Removal & Installation

2 Page 2 of 9 Raise and support vehicle. Remove wheel. Loosen 4 lower ball joint set bolts. DO NOT remove bolts. Remove cotter pin and nut from tie rod end and lower ball joint. Disconnect tie rod end from lower ball joint. Disconnect lower ball joint from lower control arm. Remove 4 lower ball joint set bolts. While lifting upper control arm and steering knuckle, remove lower ball joint. To remove upper ball joint, remove steering knuckle with axle hub. See STEERING KNUCKLE. Remove wire and boot. Using snap ring expander, remove snap ring. Remove upper ball joint from upper control arm. To install, reverse removal procedure. Tighten all nuts and bolts to specification. See TORQUE SPECIFICATIONS. Check wheel alignment. See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. LOWER CONTROL ARM Removal Raise and support vehicle. Remove front wheels. Remove cotter pin and nut. Disconnect right and left tie rod ends from lower ball joint. Remove power steering gear set bolts and nuts. Remove nut, and disconnect stabilizer bar link from lower control arm. Disconnect shock absorber from lower control arm. Remove cotter pin and nut. Disconnect lower ball joint from lower control arm. Mark front and rear cam plates and chassis frame for installation reference. Remove 2 cam plates, bolts and adjuster cams. See Fig. 1. Shift power steering gear rearward, and remove lower control arm.

3 Page 3 of 9

4 Page 4 of 9 Fig. 1: Exploded View Of Lower Control Arm Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Bushing Replacement Using a chisel and hammer, pry up flange of bushing. Using Split Clamp Plate ( ) and press, press out bushing from lower control arms. Press in new bushings with adapter. DO NOT apply grease or oil to bushings. Installation Shift power steering gear rearward, and install lower control arm with 2 cams, bolts and cam plates. Align reference marks and torque bolts. See TORQUE SPECIFICATIONS. Reconnect lower ball joint to lower suspension arm. Install nut and NEW cotter pin. Reconnect shock absorber and stabilizer bar link to lower control arm. Install power steering gear. Tighten nuts and bolts to specification. See TORQUE SPECIFICATIONS. See Fig. 2. Reconnect right and left tie rod ends to lower ball joint with nuts and new cotter pins.

5 Page 5 of 9 Fig. 2: Location Of Power Steering Gear Mounting Bolts & Nuts Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 4. Install wheels. Tighten all remaining nuts and bolts to specification. See TORQUE SPECIFICATIONS. Lower vehicle. Check front wheel alignment. See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. SHOCK ABSORBER Removal & Installation Raise and support vehicle. Remove wheel. Remove nuts and washer retaining shock absorber to bracket. DO NOT remove bolt. Remove nuts, shock absorber and coil spring. To install, reverse removal procedure. STABILIZER BAR Removal Raise and support vehicle. Remove 2 nuts and disconnect stabilizer bar links from lower control arms. Remove bolts, nuts and stabilizer bar with cushions and brackets. Remove stabilizer bar link, 2 retainers and bushings from stabilizer bar. Inspection Inspect bushings for wear, and replace as necessary. Installation To install, reverse removal procedure. Tighten stabilizer-to-lower control arm nuts to specification. See TORQUE SPECIFICATIONS. HUB & KNUCKLE Removal 4. Raise and support vehicle. Remove wheel. Remove grease cap. On 4WD models, disconnect drive shaft. Remove cotter pin and lock cap. While depressing brakes, remove lock nut. On models with ABS, remove 2 bolts, and disconnect ABS speed sensor and harness clamp from steering knuckle. On all models, remove brake caliper and disc. Remove shock absorber. See SHOCK ABSORBER. Remove bolts and disconnect lower ball joint. Remove cotter pin and loosen nut. Disconnect and remove steering knuckle. Installation

6 Page 6 of 9 4. On 4WD models, install drive shaft into axle hub and temporarily tighten nut. Connect steering knuckle to upper control arm. Install nut and new cotter pin. On all models, connect lower ball joint to steering knuckle with 4 bolts. Install shock absorber. See SHOCK ABSORBER. Install disc, brake caliper and 2 bolts. Install brake line clamp to steering knuckle with bolt. On models with ABS, connect speed sensor and wire harness clamp to steering knuckle. Install bolts. Install drive shaft lock nut. Install lock cap and new cotter pin. Install grease cap and front wheel. Depress brake pedal several times. Tighten all nuts and bolts to specification. See TORQUE SPECIFICATIONS. Check wheel alignment. See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. UPPER CONTROL ARM Removal Raise and support vehicle. Remove wheel. Remove shock absorber with coil spring. See SHOCK ABSORBER. On models with ABS, remove speed sensor and wire harness clamp from steering knuckle and upper control arm. On all models, remove cotter pin, loosen nut and disconnect upper ball joint. Support steering knuckle, and set aside. Remove 4 clips and fender apron seal. See Fig. 3. Disengage 2 brake lines and fuel line. Remove nut and brake line clamp. Remove nut, bolt, 2 washers and upper control arm.

7 Page 7 of 9

8 Page 8 of 9 Fig. 3: Exploded View Of Upper Control Arm Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Bushing Replacement Using a chisel and hammer, pry up flange of bushing. Using Split Clamp ( ) and press, remove bushing. Press in new rear bushing. Installation To install, reverse removal procedure. Tighten all nuts and bolts to specification. See TORQUE SPECIFICATIONS. TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) Adjusting Cam Bolts 96 (130) Brake Line Clamp-To-Knuckle Arm Bolt 21 (28) Disc Brake Caliper 90 (123) Drive Shaft Lock Nut 173 (235) Lower Ball Joint-To-Lower Control Arm Nut 103 (140) Lower Ball Joint-To-Steering Knuckle Bolts 59 (80) Lower Control Arm-To-Frame Bolts 96 (130) Power Steering Gear Bolts/Nuts "A" Bolt 122 (165) "B" Nut 96 (130) "C" Bolt & Nut 122 (165) Shock Absorber-To-Frame Nuts 47 (64) Shock Absorber-To-Lower Control Arm Bolt/Nut 100 (135) Stabilizer Bar Link Nuts 14 (19) Stabilizer Bar-To-Lower Control Arm Nuts 51 (69) Steering Knuckle-To-Upper Control Arm Bolt 77 (105) Tie Rod End Lock Nuts 41 (55) Tie Rod Ends-To-Lower Ball Joint Nuts 67 (91) Upper Ball Joint-To-Upper Control Arm Nut 77 (105) Upper Control Arm-To-Frame Nut 72 (98) Wheel Lug Nut 81 (110) INCH Lbs. (N.m) ABS Speed Sensor Wire Harness 71 (8) Brake & Fuel Line Clamp 49 (5.5)

9 Page 9 of Mitchell Repair Information Co., LLC.

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically

More information

Page 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).

More information

1994 Mazda MX-5 Miata. SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front

1994 Mazda MX-5 Miata. SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front DESCRIPTION An independent front suspension with MacPherson-type struts is used on all models. Miata uses double wishbone design upper and lower control

More information

1997 Mazda MX-5 Miata SUSPENSION Front - Miata

1997 Mazda MX-5 Miata SUSPENSION Front - Miata 1997-2000 SUSPENSION Front - Miata DESCRIPTION NOTE: Mazda did not produce 1998 Miata models. Front suspension is an independent, double wishbone design using upper and lower control arms. A spring over

More information

2000 Honda Accord EX

2000 Honda Accord EX HUB & KNUCKLE ASSEMBLY Removal (Except Odyssey & S2000) 1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and

More information

SA 8 FRONT AXLE HUB COMPONENTS

SA 8 FRONT AXLE HUB COMPONENTS SA8 FRONT AXLE HUB COMPONENTS SA9 REMOVAL OF FRONT AXLE HUB 1. REMOVE COTTER PIN, LOCK NUT CAP AND BEARING LOCK NUT (a) Remove the cotter pin and lock nut cap. (b) Loosen the bearing lock nut while depressing

More information

SUSPENSION. Front - Corvette

SUSPENSION. Front - Corvette 1998-99 SUSPENSION Front - Corvette DESCRIPTION The major suspension components are made of high-strength, lightweight, forged aluminum alloy. A fiberglass single-leaf spring is mounted transversely below

More information

1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2

1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:

More information

SUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.

More information

1998 Plymouth Breeze SUSPENSION' 'Rear - Cirrus, Stratus, Breeze & Sebring Convertible SUSPENSION

1998 Plymouth Breeze SUSPENSION' 'Rear - Cirrus, Stratus, Breeze & Sebring Convertible SUSPENSION DESCRIPTION 1998-99 SUSPENSION Rear - Cirrus, Stratus, Breeze & Sebring Convertible Rear suspension uses a short/long arm independent design. See Fig. 1. Each side consists of a strut assembly, upper control

More information

Title: FRONT BRAKE VIBRATION Models: Tundra. Front Brake Caliper & Rotor Replacement (2WD, Both Sides)

Title: FRONT BRAKE VIBRATION Models: Tundra. Front Brake Caliper & Rotor Replacement (2WD, Both Sides) Technical Service BULLETIN September 16, 2002 Title: FRONT BRAKE VIBRATION Models: 00-03 Tundra BR004-02 BRAKES TSB REVISION NOTICE: S March 5, 2004: A torque speification on page 10, step 24, was changed.

More information

FRONT AXLE AND SUSPENSION FA 1

FRONT AXLE AND SUSPENSION FA 1 FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated

More information

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1. 2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page

More information

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension

More information

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica

More information

AXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS

AXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS AXLE SHAFTS - 2.2L 1994 Toyota Celica 1994 DRIVE AXLES Toyota FWD Axle Shafts Celica 2.2L 4 Cyl DESCRIPTION Axle shafts transfer power from transaxle to the front wheels. Axle shaft consists of axle shaft

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN September 12, 2002 Title: Models: 00 05 Tundra BR004-02 BRAKES TSB REVISION NOTICE: April 4, 2005: Applicable Vehicles has been updated to include 2003 2005 model years. The

More information

SUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20

SUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20 SUSPENSION - FRONT 1992 Infiniti G20 1991-92 SUSPENSION Front G20 DESCRIPTION G20 uses a 4-wheel independent multi-link suspension system. Transverse links are connected to bottom of steering knuckle.

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

A proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.

A proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting. Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES

More information

REPLACEMENT 1. REMOVE FRONT WHEEL

REPLACEMENT 1. REMOVE FRONT WHEEL 3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake

More information

BRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM

BRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM Article Text ARTICLE BEGINNING 1992 BRAKES Chrysler Motors/Mitsubishi - Disc & Drum Chrysler Motors: Colt, Colt 200, Colt Vista, Ram-50, Stealth, Summit, Summit Wagon; Mitsubishi: Diamante, Eclipse, Expo/Expo

More information

07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES

07-13 TOYOTA TUNDRA 2WD 6 LIFT SPINDLES MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT

More information

2003 Ford Focus ZTW SUSPENSION Front - Focus

2003 Ford Focus ZTW SUSPENSION Front - Focus HUB/STEERING KNUCKLE ASSEMBLY Removal 1. Loosen the strut tower nuts by at least five turns. See Fig. 4. Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL

More information

2004 Explorer/Mountaineer Workshop Manual

2004 Explorer/Mountaineer Workshop Manual Page 1 of 6 SECTION 204-00: Suspension System 2004 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/05/2005 Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm

More information

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet

More information

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage

More information

Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED

Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Page 1 of 8 Section 05-04: Halfshaft, Front Wheel 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool

More information

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES 2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential

More information

TOYOTA COROLLA LOWERING SPRINGS Preparation

TOYOTA COROLLA LOWERING SPRINGS Preparation Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description

More information

INSTALLATION INSTRUCTION 88146

INSTALLATION INSTRUCTION 88146 INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS ZJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 14 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION

More information

OVERVIEW: KIT INCLUDES:

OVERVIEW: KIT INCLUDES: Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION FRONT DISC BRAKE PADS 1. Raise and support front of vehicle. Remove wheels. Remove caliper bolt and brakeline bracket bolts. Pivot caliper aside. Remove pads and pad shim. Remove

More information

www.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on

More information

FRONT AXLE HUB SUB-ASSY LH

FRONT AXLE HUB SUB-ASSY LH 3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)

More information

REAR HUB UNIT BEARING

REAR HUB UNIT BEARING 2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL

More information

FRONT SUSPENSION LOCATION INDEX

FRONT SUSPENSION LOCATION INDEX 1. Remove the front suspension tower bar. (See FRONT SUSPENSION TOWER BAR REMOVAL/INSTALLATION.) 2007 Mazda MX-5 Miata Sport 2007 SUSPENSION Front Suspension - MX-5 Miata FRONT SUSPENSION LOCATION INDEX

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

JOINT SHAFT REMOVAL/INSTALLATION

JOINT SHAFT REMOVAL/INSTALLATION 2001 MPV 2001 - MPV - Workshop Manual - Driveline/Axle JOINT SHAFT REMOVAL/INSTALLATION Report a problem with this article Performing the following procedures without first removing the ABS wheel speed

More information

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1 SUENSION SUENSION SYSTEM 1 SUENSION SYSTEM Suspension system Vehicle is unstable Bottoming Sways/pitches Wheels shimmy Abnormal tire wear Vehice pull PROBLEM SYMPTOMS TABLE Use the table below to help

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS DN SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 13 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING PRE-ALIGNMENT

More information

1994 Mazda MX-5 Miata. BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum BRAKES Mazda - Disc & Drum

1994 Mazda MX-5 Miata. BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum BRAKES Mazda - Disc & Drum BRAKE PEDAL FREE PLAY 1994 Mazda MX-5 Miata DESCRIPTION & OPERATION BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum NOTE: For information on anti-lock brake systems, see ANTI-LOCK BRAKE SYSTEM article in

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING DIAGNOSIS AND TESTING SUSPENSION AND STEERING SYSTEM 2007 SUSPENSION Suspension - Nitro CONDITION POSSIBLE CAUSES CORRECTION FRONT END NOISE 1. Loose or worn wheel bearings. 1. Replace wheel bearings.

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION Page 1 of 6 REMOVAL & INSTALLATION AXLE SHAFTS Removal Raise and support vehicle. Remove front wheels. Remove engine undercovers. Remove cotter pin and lock nut cap. See Fig. 2. Apply brakes and remove

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect

More information

3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17

3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17 FRONT AXLE DRIVE SHAFT SYSTEM 3. Front Axle A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. 6) Remove the disc rotor from hub. If the disc rotor seizes up within

More information

If it exceeds the maximum specification, replace the propeller shaft.

If it exceeds the maximum specification, replace the propeller shaft. If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown

More information

ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front

ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle

More information

BRAKE SYSTEM Article Text 1996 Toyota RAV4 For Copyright 1998 Mitchell Repair Information Company, LLC Wednesday, September 13, :30PM

BRAKE SYSTEM Article Text 1996 Toyota RAV4 For Copyright 1998 Mitchell Repair Information Company, LLC Wednesday, September 13, :30PM Article Text ARTICLE BEGINNING 1996 BRAKES Toyota - Disc & Drum RAV4 * PLEASE READ THIS FIRST * WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see

More information

10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic

10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic 2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 12 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 13 ALIGNMENT INDEX page DESCRIPTION AND OPERATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION

More information

Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles

Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical

More information

SUSPENSION AND AXLE SA 1

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE SA1 SA2 TROUBLESHOOTING SUSPENSION AND AXLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the

More information

2010 Jeep Truck Compass 4WD L4-2.4L

2010 Jeep Truck Compass 4WD L4-2.4L 1 of 8 3/18/2013 5:21 PM 2010 Jeep Truck Compass 4WD L4-2.4L Vehicle» Transmission and Drivetrain» Drive Axles, Bearings and Joints» Axle Shaft Assembly» Service and Repair» Half Shaft - Removal» Front

More information

2001 Toyota MR ENGINES' '1.8L 4-Cylinder

2001 Toyota MR ENGINES' '1.8L 4-Cylinder TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator

More information

BOSS/ULTIMATE LIFT INSTALLATION INSTRUCTIONS 07+ TUNDRA.

BOSS/ULTIMATE LIFT INSTALLATION INSTRUCTIONS 07+ TUNDRA. BOSS/ULTIMATE LIFT INSTALLATION INSTRUCTIONS 07+ TUNDRA support@toyteclifts.com. Prior to installation, please read all install directions and paperwork provided. ToyTec Lifts L.L.C. recommends that all

More information

1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans

1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans DESCRIPTION & OPERATION 1999-2000 BRAKES Disc & Drum - Trucks & Vans WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see appropriate ANTI-LOCK article.

More information

STEERING SYSTEM - MANUAL

STEERING SYSTEM - MANUAL Article Text ARTICLE BEGINNING 1991-92 STEERING Chrysler Motors/Mitsubishi - Manual Steering - Rack & Pinion Dodge; Colt, Colt Vista, Colt 200, Eagle; Summit Mitsubishi; Eclipse, Mirage, Precis DESCRIPTION

More information

DIFFERENTIALS & AXLE SHAFTS

DIFFERENTIALS & AXLE SHAFTS DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

Wheel bearing housing, removing and installing

Wheel bearing housing, removing and installing Page 1 of 17 40-54 Wheel bearing housing, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove bolt for drive axle. WARNING!

More information

Suspension System RS6582B

Suspension System RS6582B Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS WJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 4 page REAR SUSPENSION... 15 ALIGNMENT INDEX page AND WHEEL ALIGNMENT... 1 SERVICE PROCEDURES PRE-ALIGNMENT... 2 AND WHEEL

More information

TOYOTA 4-RUNNER KIT 5 KIT

TOYOTA 4-RUNNER KIT 5 KIT 92173600 1990-1995 TOYOTA 4-RUNNER KIT 5 KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

'88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N

'88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6 SUSPENSION SYSTEM P/N 4/10/13 '88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N. 10-41888 INSTALLATION INSTRUCTIONS APPLICATION WARNING: Applicable for hub mounted ABS sensor models only. Not for 1992-94

More information

AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1

AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1 AXLE AXLE SYSTEM 1 AXLE SYSTEM PROBLEM SYMPTOMS TABLE HINT: Use the table below to help you find the cause of the problem. The numbers indicate the ranked order of probability of each of the possible causes.

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION REAR BRAKE CALIPER NOTE: For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any

More information

1 M-3000-H4 F150 4X4 Lowering Kit

1 M-3000-H4 F150 4X4 Lowering Kit READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.

More information

INSTALLATION INSTRUCTION 88148

INSTALLATION INSTRUCTION 88148 INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION

More information

DRIVE AXLES. Differentials & Axle Shafts - Corvette

DRIVE AXLES. Differentials & Axle Shafts - Corvette DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case

More information

REAR SUSPENSION SECTION CONTENTS E SUSPENSION RSU-1 RSU

REAR SUSPENSION SECTION CONTENTS E SUSPENSION RSU-1 RSU E SUSPENSION A SECTION REAR SUSPENSION B C D CONTENTS RSU PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

WD CHEVY/GM LIFT

WD CHEVY/GM LIFT 92750100 99-06 2WD CHEVY/GM 1500 3 LIFT Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these

More information

components is critical so that the splines are not damaged. NOTE: Never force the hub unit bearing assembly onto the shaft or strike with a hammer.

components is critical so that the splines are not damaged. NOTE: Never force the hub unit bearing assembly onto the shaft or strike with a hammer. Automotive TechTips Volume 6 Issue 4 Part 3 of a 3-Part Series Installing a Hub Unit Bearing Assembly and Steering Knuckle Guidelines for Timken continues to lead the hub unit bearing evolution by providing

More information

ALLDATA Online Dodge Truck Caravan V L - Front. Front

ALLDATA Online Dodge Truck Caravan V L - Front. Front Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle

More information

REAR AXLE AND SUSPENSION RA 1

REAR AXLE AND SUSPENSION RA 1 REAR AXLE AND SUSPENSION RA1 RA2 REAR AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated Replace tires or inflate to

More information

INSTALLATION INSTRUCTION 88051

INSTALLATION INSTRUCTION 88051 INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT

More information

WHEEL ALIGNMENT PROCEDURES

WHEEL ALIGNMENT PROCEDURES Page 1 of 8 WHEEL ALIGNMENT PROCEDURES TURNING ANGLE Turn steering wheel fully right and then left, and observe turning radius on both wheels. If turning radius is incorrect, inspect and replace any damaged

More information

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1 SUENSION SUENSION SYSTEM 1 Vehicle/pulls Bottoming Sway/pitches Wheel shimmy Abnormal tire wear SUENSION SYSTEM PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of the problem. The

More information

ARTICLE BEGINNING DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Rear. Golf III

ARTICLE BEGINNING DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Rear. Golf III Article Text ARTICLE BEGINNING 1995-96 SUSPENSION Rear Golf III DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake drums

More information

Symptom Suspect Area See page. 3. Shock absorber (Worn out) 3. Shock absorber (Worn out)

Symptom Suspect Area See page. 3. Shock absorber (Worn out) 3. Shock absorber (Worn out) TROUBLESHOOTING PROBLEM SYMPTOMS TABLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part

More information

NOTICE TO DEALER AND VEHICLE OWNER

NOTICE TO DEALER AND VEHICLE OWNER 921322300 *1322BAG1* 1322BAG1 2009-17 Dodge 2wd 1500 6 Lift Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system.

More information

2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement

2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement 2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement Exploded View Special Tools Required Ball joint thread protector, 14 mm 071AF-S3VA000 Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool,

More information

KG09100BK / KG09101BK GM WD.

KG09100BK / KG09101BK GM WD. KG09100BK / KG09101BK GM. 1988-2006 2 WD. KG09101BK KG09100BK Instruction Sheet: P10476-05 2013 Daystar Products International Inc. Tools Needed Quantity Description 1 Floor Jack 2 Jack Stands 2 Wheel

More information

»Product» Safety Warning

»Product» Safety Warning T2502 Installation Instructions 2007-2017 Toyota Tundra 4wd 5" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

*1234BAG1 1234BAG WD CHEVY/GM LIFT N200

*1234BAG1 1234BAG WD CHEVY/GM LIFT N200 *1234BAG1 1234BAG1 921234N200 99-06 2WD CHEVY/GM 1500 6 LIFT Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs this system.

More information

WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT

WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT -YA WU-07 5 x 4.5 -YA WU-08 5 x 5.5 *THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS AND YA WU-08 WILL CHANGE BOLT PATTERN TO 5 ON 5.5*

More information

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation Preparation Part Number: PTR07-47100 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Nut 4 1 Instructions Hardware Bag Contents Item # Quantity Reqd. Description 1 2

More information

Lower Arm ( ) Special Service Tools. Removal.

Lower Arm ( ) Special Service Tools. Removal. Page 1 of 6 (60.35.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers

More information

4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.

4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy. OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,

More information

'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS

'99-03 CHEVROLET/GMC IFS 4WD 6 SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS 1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures

More information