POWER TROWEL. Models / 95855

Transcription

1 POWER TROWEL Models / ASSEMBLY And Operating Instructions CAUTION! Your Warranty Is Voided If: You do not put engine oil in the Engine s crankcase prior to its first use. Before each use, check the oil level. Never run the Engine with low or no engine oil. Running the Trowel with low or no oil will permanently damage the unit. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA Visit our website at: Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright 2007 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call

2 SPECIFICATIONS SKU Trowel Type Walk Behind Handle Controls Throttle / ON/OFF Switch Turn Knob To Raise/Lower Pitch Of Blades Blade Cage Type Triple Rod Guarding Cage Diameter 30-1/4 36-9/64 Number of Blades 4 Blade Type Finishing Blade Size 11 L x 6 W 14 L x 6 W Blade Diameter 29-7/8 34-5/8 Blade Pitch 5-10 Adjustment Float Type Float Disc (Included) Float Diameter 31-1/4 37-5/64 Engine Type Briggs & Stratton I/C 6.5 HP Model Number : Engine Type: Required Fuel Type: Unleaded Gasoline Only Robin/Subaru OHC 7.0 HP Model Number: EX-21OD Engine Type: 5FJXS.2111GA Required Fuel Type: Unleaded Gasoline Only Approximate Weight 225 lb. 242 lb. SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES AND PRECAUTIONS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. SKU 93544/95855 For technical questions, please call Page 2

3 Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. PERSONAL SAFETY Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Avoid accidental starting. Be sure the Throttle is in its OFF position before moving the Power Trowel and before performing any service, maintenance, or cleaning procedures on the unit. Remove adjusting keys or wrenches before turning the Power Trowel on. A wrench or a key that is left attached to a rotating part of the machine may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. Use safety equipment. Always wear eye protection. Always wear ANSI approved safety impact goggles when using this product. ANSI approved hearing protection must also be used. Wear safety shoes for added protection. TOOL USE AND CARE Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use the Power Trowel if the Throttle does not turn it on or off. Any tool that cannot be controlled with its Throttle is dangerous and must be serviced by a qualified technician. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools Do not use until repaired. SKU 93544/95855 For technical questions, please call Page 3

4 5. 6. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instructions in the Inspection, Maintenance, And Cleaning section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES AND PRECAUTIONS Your Warranty is voided if: You do not put engine oil in the Engine s crankcase prior to its first use. Before each use, check the oil level. Never run the Engine with low or no engine oil. Running the Engine with low or no oil will permanently damage the unit Maintain labels and nameplates on the Power Trowel. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Make sure the Power Trowel is used on a flat, level, surface to maintain stability of the tool. Do not use the Power Trowel on inclines. Never stand on the Power Trowel. Serious injury could result if the Power Trowel is tipped. Never leave the Power Trowel unattended when it is running. Always turn off the Power Trowel before leaving. Do not allow children and other unauthorized people to handle or play with the Power Trowel. Industrial applications must follow OSHA guidelines. Prior to using the Power Trowel, make sure to clear away large rocks, sticks, and other foreign materials off the ground surface to avoid damage to the Power Trowel and/or personal injury. Use caution when working around pipes or ducts protruding from the floor or slab edges. SKU 93544/95855 For technical questions, please call Page 4

5 Do not allow other people to stand beside the Power Trowel when the tool is being operated. Always keep hands and feet safely away from the moving parts of the Power Trowel. Always make sure all guards are in place and in proper working condition prior to starting the Power Trowel. When starting the Power Trowel, do not exceed the 1/3 Throttle position. A higher setting may cause the centrifugal clutch to engage and the Blades to rotate. Always maintain a firm grip on the Handle assembly with both hands to ensure proper control. While using the Power Trowel, the operator must always secure the Safety Stop Switch with the left hand for proper operation of the Switch. This Power Trowel is designed for outdoor use only. Do not operate the Power Trowel in a closed area or in a poorly ventilated area. When running, the Engine of this Power Trowel produces carbon monoxide, a colorless, odorless, toxic fume that, when inhaled, can cause serious personal injury or death. Whenever possible, use a carbon monoxide detector (not included) to detect excessive carbon monoxide fumes in the work area and in the surrounding area. Do not force the Power Trowel. This tool will do the work better and safer at the speed and capacity for which it was designed. FIRE AND EXPLOSION PRECAUTIONS Gasoline fuel and fumes are flammable, and potentially explosive. Use proper fuel storage and handling procedures. Always have multiple ABC class fire extinguishers nearby. Keep the Power Trowel and surrounding areas clean at all times. When spills of fuel or oil occur, they must be cleaned up immediately. Dispose of fluids and cleaning materials as per any local, state, or federal codes and regulations. Store oil rags in a covered metal container. Never store fuel or other flammable materials near the Power Trowel. Do not smoke, or allow sparks, flames, or other sources of ignition around the Power Trowel. Keep grounded conductive objects, such as tools, away from exposed, live electrical parts and connections to avoid sparking or arcing. These events could ignite fumes or vapors. SKU 93544/95855 For technical questions, please call Page 5

6 7. Do not refill the Fuel Tank while the Engine is running or while the Engine is still hot. Do not operate the Power Trowel with known leaks in the fuel system. Use only Engine manufacturer recommended fuel and oil. MECHANICAL PRECAUTIONS Prior to performing service, maintenance, or cleaning procedures, always make sure the Throttle is in its OFF position. Allow the Engine to completely cool. Then, remove the spark plug from the Engine. Do not alter or adjust any part of the Power Trowel or Engine that is assembled and supplied by the manufacturer. Always follow and complete scheduled Power Trowel (page 12) and Engine (follow engine manufacturer s recommendations) maintenance. CHEMICAL PRECAUTIONS Avoid contact with hot fuel, oil, exhaust fumes, and solid surfaces. Avoid body contact with fuels, oils, and lubricants used in the Power Trowel and Engine. If swallowed, seek medical treatment immediately. Do not induce vomiting if fuel is swallowed. For skin contact, immediately wash with soap and water. For eye contact, immediately flush eyes with clean water. MISC. PRECAUTIONS WARNING! The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code , et seq.) Prolonged exposure to noise levels above 85 dba is hazardous to hearing. Always wear ANSI approved hearing protection when operating or working around the Power Trowel when it is running. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. Caution is necessary when near engine s magneto or recoil starter. WARNING! The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 93544/95855 For technical questions, please call Page 6

7 UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on pages 16 and 17 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY INSTRUCTIONS Both models come with the main column folded down in the middle. This column must be assembled in the straight position before operating the trowel. (See Figure 1 below.) Figure 1 Figure 2 Connecting Bolt (7C) Column Handle (9C) To straighten and secure the two parts of the column, swing the end of the column up and secure it in place using the Connecting Bolt and Column Handle (9C). (See Figure 2 and assembly diagram page 1) PRE-OPERATING INSTRUCTIONS CAUTION! Turn the Throttle (5C) of the Power Trowel to its OFF position and disconnect the Spark Plug wire prior to performing any service, maintenance, or cleaning. IMPORTANT! Prior to first using the Power Trowel, the Engine MUST be filled with the Engine manufacturer s recommended type of engine oil. (Refer to Engine manufacturer s manual.) Prior to first using the Power Trowel, the Fuel Tank MUST be filled with high octane unleaded gasoline. (Refer to Engine manufacturer s manual.) SKU 93544/95855 For technical questions, please call Page 7

8 Starting The Power Trowel: OPERATING INSTRUCTIONS 5. Before starting the Power Trowel, make sure to check the Engine for proper fuel and oil levels. (See Engine manufacturer s manual.) With assistance, set the Power Trowel on the concrete slab. NOTE: Avoid leaving the Power Trowel running in one spot on the concrete slab to maintain surface tolerances. Use caution when running the Power Trowel in areas where standing water is evident, as the Power Trowel will tend to skate away. Maintain control at all times. Note: Determining the proper amount of cure of the concrete is important for achieving a uniform machine-troweled finish. (See operating tips on page 9.) Set the Throttle (5C) at its 1/3 position. (See Figure D.) Make sure the Engine Cut-off Switch is in its ON position. Then, hold the Power Trowel firmly and start the Engine. (See Figures E and F.) (See Engine manufacturer s manual for starting/stopping instructions.) After the Engine starts, move the Engine choke to its fully open position to let the Engine warm up before operating. Allow longer warm up in cold weather. (See Engine manufacturer s manual for starting/stopping instructions.) Figure D Figure E Figure F Jam Nut (12G) Engine Cut-off Switch Throttle (5C) Engine Cut-off Switch (8C) Throttle (5C) 6. Hold the Power Trowel firmly, behind the center of the Handle, with good footing. Turn the Throttle (5C) completely clockwise. This will make the blades spin. (See Figure E.) SKU 93544/95855 For technical questions, please call Page 8

9 7. 8. With a firm grip on the handle, guide the Power Trowel on the concrete slab: a. b. c. d. e. OPERATING INSTRUCTIONS CONTINUED Push the Handle down and the Power Trowel will move to the right. Lift the Handle up and the Power Trowel will move to the left. Slightly twist to the right and the Power Trowel will move forward. Slightly twist to the left and the Power Trowel will move backward. Hold the Handle in the neutral position and the Power Trowel will remain stationary. Adjust the Tilt Knob (9C) to get the proper troweling angle according to the requirement of your job. (See Figure D.) Stopping The Power Trowel: To stop the Power Trowel, push the Throttle (5C) to its lowest position. Place the Engine Cut-off Switch (8C) in its OFF position. Then, turn off the Engine. (See Figure E and F page 8, and refer to Engine manufacturer s manual.) Carefully lift the trowel from the concrete slab. Clean all concrete from the equipment and store in a safe, dry location out of children s reach. Preparing The Concrete Surface: OPERATING TIPS The use of a mechanical or vibrating screed (not included) to strike the surface will provide better compaction of the slab and produce an ideal surface for finishing. Be aware that the Power Trowel cannot repair or correct a poorly prepared slab. Attaching The Floating Disc: Make sure engine is off and blade is free of cement before attaching disc. Place the Trowel over the disc. Twist the blades until they lock into the Floating Disc. (See Figure G to the right.) To remove the Floating Disc, twist the Trowel Blades counterclockwise, out of the Floating Disc s Blade holders. Figure G SKU 93544/95855 For technical questions, please call Page 9

10 The Floating Operation: OPERATING Tips CONTINUED Make sure the Blades (4B) are free of all cement. The Blades must also be in the flat position (parallel to the ground surface). When the slab has set sufficiently that the operator s footprints leave a very slight impression, the slab is ready for the finishing step. A Floating Disc (included) should be used to float the surface up to the walls or as close to any obstacles as possible and then be followed by a mini-trowel (not included) for the remainder. When the surface has set properly, continue on to the next phase. The Finishing Operation: After the floating operation, clean the Blades of concrete collected during the floating operation. Adjusting the Carriage Bolt (11G) permits unlimited pitch variation at all times. When finishing, the setting up (hardening) of the concrete slab may vary from area to area across the surface, so the pitch must be changed as required. (See Figure E.) Set the pitch to approximately 1/4, using the Carriage Bolt (11G), for the first pass and then continue to increase the pitch on following passes, repeating the passes to until the desired floor finish is obtained. To set the pitch, loosen the Jam Nut (12G). Adjust the Carriage Bolt (11G) so that it is touching the bottom of the Plate (3G). Then, tighten the Jam Nut against the Carriage Bolt. NOTE: It is important the once the Carriage Bolt is adjusted to the proper height it does not move before or during the tightening of the Jam Nut. Repeat this process for the remaining three Blades (4B). (See Figure E page 8) SKU 93544/95855 For technical questions, please call Page 10

11 INSPECTION, MAINTENANCE, AND CLEANING WARNING! Always make sure the Throttle (5C) of the Engine Cut-off Switch (8C) is in its OFF position and the Spark Plug is removed from the Engine prior to performing any service, maintenance, or cleaning of the unit. (See Figure E and F page 8.) Before each use, inspect the general condition of the Power Trowel. Check for loose screws, misalignment or binding of moving parts, cracked, bent, or broken parts, damaged Engine parts, and any other condition that may affect the safe operation of the Power Trowel. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. Before each use, check the Engine oil level of the Power Trowel. (Refer to the Engine manufacturer s manual for lubricating and other maintenance instructions.) Daily, with a garden hose, clean the Power Trowel after each use to prevent hardening of concrete on the unit. Exercise caution to avoid getting water on the engine and engine components. Hard concrete on the Power Trowel greatly increases the weight of the unit and reduces efficiency. To change the V-Belt, unscrew and remove the Nut that holds the Pulley Cover (41H) in place. Then, remove the Pulley Cover. Check to make sure the Engine Cut-off Switch (8C) is in its OFF position. (See Figures E and F on page 8.) Rotate the Pulley (44H) while removing the old V-Belt. Once removed, install a new V-Belt. Reinstall the Pulley Cover (41H). Then, tighten the Nut to secure the Pulley Cover in place. Always store the Power Trowel in a clean, dry, safe location out of reach of children and other unauthorized people. NOTE: Also refer to the Engine manufacturer s manual for storage instructions. CAUTION! All maintenance, service, or repairs not mentioned in this manual must only be performed by a qualified service technician. SKU 93544/95855 For technical questions, please call Page 11

12 Machine will not start. Cannot change speed. TROUBLESHOOTING Problem Possible Cause Possible Solution Tilt function does not work. Engine Cut-off Switch does not cut off engine. WARNING! This is a very hazardous condition that must be repaired immediately to prevent serious injury. Disconnect spark plug wire and have problem repaired by qualified technician before further use. Gas or oil leak. V-Belt wears quickly, and cannot adjust the speed. Blades wear unevenly. Blade assembly does not work when engine is started. 5. Fuel tank empty. Low or no oil. Clutch is stuck. Damaged electrical wiring. The brake is in its OFF position. Blade assembly is covered with excessive concrete. Connection between blade housing and crankcase is loose. Steel wire is broken. Tilt mechanism is damaged. Engine Cut-off Switch is not properly seated in the copper clamp. Wire connection not properly adjusted or damaged. Crankcase seal is damaged. Carburetor is damaged. Gap between shaft and seal too wide. Oil seal is damaged. V-Belt is not in line vertically with the pulley. Wrong v-belt size/type for pulley. Clutch is stuck. Throttle control system does not work properly. One set of adjusting bolts not properly adjusted, and all four blades are not on the same surface. The blade is warped. Clutch is stuck. The pins of the pulley, clutch, or blades may be damaged or missing. 5. Fill fuel tank with unleaded gasoline. Fill crankcase with proper amount/type of oil. check the clutch. check the wiring. Set the brake to its ON position. Clean blade assembly of excess concrete. Tighten the connection. replace the steel wire. repair or replace tilt mechanism. Adjust the copper clamp. adjust or replace the wire connection. replace crankcase seal. repair or replace carburetor. tighten all loose connections. repair or replace oil seal. adjust pulley. install the proper size/type v-belt. check the clutch. check throttle control. Properly re-adjust bolts. Make sure all four blades are on the same surface. Replace blade. check the clutch. repair or replace the pins. SKU 93544/95855 For technical questions, please call Page 12

13 PARTS LIST Blade Guard Assembly 1A Blade Guard Assy. 1 Blade & Blade Housing Assembly 1B Cross Housing 1 2B Arm 4 3B Adjusting Shaft 4 4B Blade 4 5B Bar 4 6B Screw Sleeve 1 7B Bolt 4 8B Spring Washer 8 9B Bolt 8 10B Square Head Screw 4 11B Hex Flat Nut 4 12B Screw 8 13B Cover Cap 1 14B One Way Push Bearing 1 15B Cover 1 16B Screw 4 17B Washer 4 18B Grease Cup 4 19B Cover Sleeve 1 20B Screw 1 Handle Assembly 1C Horizontal Grip 1 2C Left Side Pipe 1 3C Right Side Pipe 1 4C Middle Pipe 1 5C Throttle 1 6C Brake Plate 1 7C Connecting Bolt 1 8C Engine Cut-off Switch 1 9C Column Handle 1 Brake Assembly 1D Brake Cover 1 2D Brake Arm 1 3D Brake Body 1 4D Nylon Sleeve 1 5D Copper Clamp 2 6D Housing 1 7D Housing Sleeve 1 8D Crosshead Screw 1 9D Crosshead Screw 2 10D Copper Screw 1 11D Copper Screw 1 12D Copper Flat Nut 3 13D Copper Flat Washer 2 14D Lock Washer 2 Brake Assembly 15D Hex Screw 2 16D Electric Wire (Blue) 1 17D Conductor Sleeve (Black) 1 18D Connector 1 Support Plate Connection Assembly 1E Upper Support Plate 1 2E Lower Support Plate 1 3E Hex Bolt 4 4E Hex Bolt 1 Throttle Control Assembly 1F Throttle Wire Housing 1 2F Throttle Spanner 1 3F Throttle Wire Clamp 1 4F Plastic Washer 2 5F Throttle Wire Assembly 1 6F Crosshead Screw 1 7F Crosshead Screw 1 8F Crosshead Screw 2 9F Lock Washer 2 10F Lock Nut 1 11F Spring Washer 1 Blade Adjusting Assembly 1G Rubber Grip 2 2G Adjusting Screw Sleeve 1 3G Plate 4 4G Shaft Circlip 1 5G Washer 1 6G Spring Washer 1 7G Sleeve 1 8G One Way Push Bearing 1 9G Knob 1 10G Spring Round Pin 1 11G Carriage Bolt 4 12G Jam Nut 4 13G Inner Hex Fixing Screw 1 14G Steel Wire Connector 1 15G Round Pin 1 16G Steel Wire 1 17G Spin Wheel Shaft 1 18G Steel Wire Connection Screw 1 19G Lock Nut 1 20G Round Pin 1 21G Spin Wheel 1 22G Push Lever 1 23G Push Lever Shaft 1 24G Fork Circlip 2 NOTE: When ordering parts, indicate the Assembly followed by its Part Number and Part Name. (i.e., Support Plate Connection Assembly, part #1E, Upper Support Plate.) SKU 93544/95855 For technical questions, please call Page 13

14 PARTS LIST (CONT.) Crankcase Assembly 1H Plate 2 2H Steel Bowl 4 3H Nut 8 4H Washer 8 5H Washer 8 6H Crosshead Screw 6 7H Inner Hex Screw 16 8H Washer 4 9H Screw Column 4 10H Rubber Pad 4 11H Crankcase Cover 1 12H Washer 1 13H Screw 1 14H Push Ring 1 15H Bearing 1 16H Turbine 1 17H Bearing 1 18H Turbine Shaft 1 19H Key 1 20H Bolt 4 21H Nut 5 22H Washer 5 23H Washer 5 24H Key 1 25H Worm Shaft 1 26H O-Ring 2 27H Washer 2 28H Right Bearing Housing 1 29H Bearing 1 Crankcase Assembly 30H Seal Ring 2 31H Crankcase Body 1 32H Bleed Screw 2 33H Bearing 1 34H Left Bearing Housing 1 35H Label 1 36H Rivet 4 37H Flat Nut 1 38H Screw Column 1 39H Key 1 40H Pressure Reducer Valve 1 41H Pulley Cover 1 42H V-Belt 1 43H Washer 4 44H Pulley 1 45H Fixing Screw 2 46H Oil View Window 1 Clutch Assembly 1I Idle Block 2 2I Clutch Cover 1 3I Spring 2 4I Clutch Wheel 1 5I Bearing 2 6I Spindle Circlip 1 7I Hole Circlip 1 NOTE: When ordering parts, indicate the Assembly followed by its Part Number and Part Name. (i.e., Clutch Assembly, part #2I, Clutch Cover ) PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 93544/95855 For technical questions, please call Page 14

15 ASSEMBLY DIAGRAM OPERATION HANDLE ASSEMBLY - C, D, E, F, G g c f d e e g NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 93544/95855 For technical questions, please call Page 15

16 ASSEMBLY DIAGRAM (CONT.) BLADE/BLADE HOUSING ASSEMBLY - B BLADE GUARD ASSEMBLY - A NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 93544/95855 For technical questions, please call Page 16

17 ASSEMBLY DIAGRAM (CONT.) CRANKCASE ASSEMBLY - H Clutch ASSEMBLY - I NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 93544/95855 For technical questions, please call Page 17

18 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state Mission Oaks Blvd. PO Box 6009 Camarillo, CA (800) SKU 93544/95855 For technical questions, please call Page 18