BEARING ADAPTERS FWD/FRONT WHEEL. Model 45210
|
|
- Ginger Booker
- 6 years ago
- Views:
Transcription
1 BEARING ADAPTERS FWD/FRONT WHEEL Model Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA Visit our website at: Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright 2001 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call Cover revised 07j; Rev 08h
2 SPECIFICATIONS TABLE Construction Low Carbon Steel Finish Black Oxide Bushing Hardness HRC25 to HRC35 Bushing Range (Outside Diameter) 2.18, 2.5, 2.62, 2.78, 2.82, 2.88, 2.9, 2.96, 3.05, 3.21, 3.28, 3.48 Sleeve Sizes 3 O.D. x 2.5 Long 3.25 O.D. x 2.53 Long 3.63 O.D. x 2.53 Long 4 O.D. x 2.53 Long Sleeve Plate Sizes 3.25 O.D. x 2.72 Step 4 O.D. x 3.2 Step Sliding Screw Size/Type 7.5 Long x.75 Diameter/16 NAT Nut Size 3 Long x.75 Diameter Washer Size 1.5 O.D. SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, operating, inspection, maintenance, and cleaning procedures. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY WARNINGS AND PRECAUTIONS 1. KEEP WORK AREA CLEAN AND DRY. Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle this product. 3. STORE IDLE EQUIPMENT. When not in use, tools and equipment should be stored in a dry location to inhibit rust. Always lock up tools and equipment and keep out of reach of children. 4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 5. USE EYE PROTECTION. Wear ANSI approved safety impact eye glasses when using this product. ANSI approved safety impact eye glasses are available from Harbor Freight Tools. 6. DRESS SAFELY. Non-skid footwear or safety shoes should be used when work- Page 2
3 ing with this product. Do not wear loose clothing or jewelry as they can become caught in moving parts. Wear a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll sleeves up above elbows. 7. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS. 8. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etcetera. 9. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not use this product when you are tired or distracted from the job at hand. 10. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace or repair damaged or worn parts immediately. 11. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. 12. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry for better and safer performance. 13. MAINTENANCE: For your safety, service and maintenance should be performed regularly by a qualified technician. 14. USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applications for which this product was designed. Do not use small equipment, tools or attachments to do the work of larger industrial equipment, tools or attachments. Do not use this product for a purpose for which it was not intended. 15. PRIOR TO USING THIS PRODUCT, MAKE SURE TO READ AND UNDERSTAND ALL INSTRUCTIONS AND SAFETY PRECAUTIONS AS OUTLINED IN THE instruction manual of the vehicle being worked on. 16. NEVER WORK UNDERNEATH A VEHICLE WITHOUT USING ADDITIONAL SAFETY SUPPORT DEVICES (I.E., JACK STANDS) TO SUPPORT THE WEIGHT OF THE VEHICLE. 17. WARNING: This product contains or produces a chemical known to the State of California to cause cancer and birth defects (or other reproductive harm). (California Health & Safety Code et seq.) Page 3
4 UNPACKING When unpacking, check to make sure the parts shown on pages 8 and 9 of this manual are included. If the part is missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. OPERATING INSTRUCTIONS NOTE: All parts mentioned below refer to the parts listed and shown on pages 8 and 9 of this manual. To Remove A Bearing/Race Assembly: 1. NOTE: The following instructions apply to most FWD vehicles and are intended to illustrate the process in general terms, not to be specific to any one make/ model vehicle. A combination of Sleeves (parts #1 thru #4), Sleeve Plates (parts #5a and 5b), and Bushings (parts #6 thru #19), will be necessary for different vehicles. Make sure to select the Sleeves deep enough to allow the removal of the bearing from the spindle. Also, make sure to select the Bushings that contact the inner/outer race of the bearing and not the ball bearings. (See Figure A, and Assy. Diagram.) 2. It will be necessary to make clear access to the bearing on both sides of the spindle. To do so, remove the vehicle s front wheel, axle nut, and outer tie rod nut. Disconnect the tie rod. Remove the front brake and brake rotor. Remove the axle from the hub, and with rope or wire, secure the axle out of the way from the job to be done. NOTE: On some models it may be necessary to loosen the lower ball joint from the steering knuckle to prevent damage to the axle from the hub. Page 4
5 STEERING KNUCKLE BALL BEARINGS INNER RACE OUTER RACE BALL BEARINGS SEAL RETAINING CLIP RETAINING CLIP FIGURE A 3. Remove the retaining clip and seal (located in the opening in the steering knuckle) from the appropriate side of the bearing. (See Figure A.) 4. Select a Sleeve (parts #1 thru #4) with a diameter large enough to rest against the outer edge of the steering knuckle. (See Figure B, and Assy. Diagram.) 5. Select a Sleeve Plate (parts #5a, #5b) that will fit snugly on the Sleeve (parts #1 thru #4) being used. (See Figure B, and Assy. Diagram.) 6. Place a Washer (part #22) on the Sliding Screw (part #21). (See Figure B, and Assy. Diagram.) SLEEVE PLATE (#5a, #5b) BUSHING (#6 - #19) SLIDING SCREW (#21) NUT (#20) WASHER (#22) WASHER (#22) SLEEVE (#1 - #4) STEERING KNUCKLE FIGURE B Page 5
6 7. Insert the Sliding Screw (part #21) with the Washer (part #22) through the Sleeve Plate (parts #5a, #5b), Sleeve (parts #1 thru #4), and the opening in the vehicle s steering knuckle. (See Figures A, B, and Assy. Diagram.) 8. Select a Bushing (parts #6 thru #19) that will slide snugly through the opening in the vehicle s steering knuckle, and place it on the end of the Sliding Screw (part #21). NOTE: Make sure to select the Bushing that contacts the inner/outer race of the bearing and not the ball bearings. (See Figures A, B, and Assy. Diagram.) 9. Place a Washer (part #22) on the end of the Sliding Screw (part #21). (See Figure B, and Assy. Diagram.) 10. Screw the Nut (part #20) on the end of the Sliding Screw (part #21). (See Figure B, and Assy. Diagram.) 11. Hold the Nut (part #20) in place with a wrench. Then, slowly screw the Sliding Screw (part #21) into the Nut while drawing the ball bearings and inner/outer race out of the opening in the vehicle s steering knuckle. (See Figures A, B, and Assy. Diagram.) 12. Once the bearing assembly (ball bearings and race) has been drawn out of the steering knuckle, disassemble the Bearing Adapter tool and store it in a clean, dry location. To Install A Bearing/Race Assembly: 1. Select a Sleeve (parts #1 thru #4) with a diameter large enough to rest against the outer edge of the steering knuckle. (See Figure C, and Assy. Diagram.) 2. Select a Sleeve Plate (parts #5a, #5b) that will fit snugly on the Sleeve (parts #1 thru #4) being used. (See Figure C, and Assy. Diagram.) 3. Place a Washer (part #22) on the Sliding Screw (part #21). (See Figure C, and Assy. Diagram.) 4. Insert the Sliding Screw (part #21) with the Washer (part #22) through the Sleeve Plate (parts #5a, #5b), Sleeve (parts #1 thru #4), and the opening in the vehicle s steering knuckle. (See Figure C, and Assy. Diagram.) 5. Slide the bearing assembly (race and ball bearings) on the end of the Sliding Screw (part #21). (See Figure C, and Assy. Diagram.) SKU For technical questions, PAGE please 6 call Page 6
7 RACE/BALL BEARINGS SLEEVE PLATE (#5a, #5b) WASHER (#22) WASHER (#22) SLIDING SCREW (#21) SLEEVE (#1 - #4) NUT (#20) BUSHING (#6 - #19) STEERING KNUCKLE FIGURE C 6. Select a Bushing (parts #6 thru #19) that will slide snugly through the opening in the vehicle s steering knuckle, and place it on the end of the Sliding Screw (part #21). NOTE: Make sure to select the Bushing that contacts the inner/outer race of the bearing and not the ball bearings. (See Figure C, and Assy. Diagram.) 7. Place a Washer (part #22) on the end of the Sliding Screw (part #21). (See Figure C, and Assy. Diagram.) 8. Screw the Nut (part #20) on the end of the Sliding Screw (part #21). (See Figure C, and Assy. Diagram.) 9. Hold the Nut (part #20) in place with a wrench. Then, slowly screw the Sliding Screw (part #21) into the Nut while drawing the bearing assembly into the opening in the vehicle s steering knuckle. (See Figure C, and Assy. Diagram.) 10. Once the bearing assembly has been drawn into the steering knuckle, disassemble the Bearing Adapter tool and store it in a clean, dry location. 11. Insert the retaining clip and seal in the opening in the steering knuckle to secure the bearing assembly in place. (See Figure A.) INSPECTION, MAINTENANCE, AND CLEANING 1. Before each use, inspect the general condition of the Bearing Adapter set. Check for cracks, breaks, or bends in the tool, and any other condition that may Page 7
8 affect its safe operation. If a problem occurs with the tool, immediately discontinue its use and have the problem corrected before further use. Do not use damaged equipment. 2. To clean, wipe with a damp cloth. You may use a mild detergent or mild solvent. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDER- TAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. PARTS LIST Part # Description Qty. 1 Sleeve (4 O.D. x 2.53 Long) 1 2 Sleeve (3.63 O.D. x 2.53 Long) 1 3 Sleeve (3.25 O.D. x 2.53 Long) 1 4 Sleeve (3 O.D. x 2.5 Long) 1 5a Small Sleeve Plate (3.25 O.D. x 2.72 Step) 1 5b Large Sleeve Plate (4 O.D. x 3.2 Step) 1 6 Bushing (2.96 O.D.) 1 7 Bushing (2.62 O.D.) 1 8 Bushing (2.18 O.D.) 1 9 Bushing (2.88 O.D.) 1 11 Bushing (2.5 O.D.) 1 12 Bushing (2.78 O.D.) 1 13 Bushing (2.82 O.D.) 1 14 Bushing (2.82 O.D.) 1 15 Bushing (2.9 O.D.) 1 16 Bushing (3.48 O.D.) 1 17 Bushing (3.05 O.D.) 1 18 Bushing (3.21 O.D.) 1 19 Bushing (3.28 O.D.) 1 20 Nut (3 Long x.75 Dia.) 1 21 Sliding Screw (7.5 Long x.75 Dia.) 1 22 Washer (1.5 O.D.) 2 23 Blow Mold Carrying Case 1 Page 8
9 PARTS DIAGRAM b 5a 21 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 9
STEEL SIDE PANEL KIT. Model (FOR USE WITH MODEL FOLDABLE UTILITY TRAILER)
STEEL SIDE PANEL KIT Model 47423 (FOR USE WITH MODEL 42709 FOLDABLE UTILITY TRAILER) Set up and Operating Instructions (MODEL 42709 TRAILER and TARP NOT INCLUDED. TARP SOLD SEPARATELY. Shown for illustration
More informationWOODEN SIDE PANEL KIT
WOODEN SIDE PANEL KIT Model 40141 (FOR USE WITH MODEL 42709 UTILITY TRAILER) ASSEMBLY INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http//www.harborfreight.com Copyright
More informationWHEEL KIT FOR 13 HP GENERATOR
WHEEL KIT FOR 13 HP GENERATOR 94192 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More informationHYDRAULIC SPRING COMPRESSOR SET
HYDRAULIC SPRING COMPRESSOR SET Model 47890 ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2002 by Harbor
More informationWINDSHIELD REMOVAL KIT
WINDSHIELD REMOVAL KIT 94180 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More information4 TIER STOCKER SERVICE CART
4 TIER STOCKER SERVICE CART 90160 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools.
More informationMOUNTABLE WALL SINK ASSEMBLY AND OPERATING INSTRUCTIONS
MOUNTABLE WALL SINK 90326 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools. All
More informationMINIATURE ALUMINUM JACK STANDS (1 PAIR) Model 90892
MINIATURE ALUMINUM JACK STANDS (1 PAIR) Model 90892 ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2003 by
More informationDISC BRAKE CALIPER TOOL SET
DISC BRAKE CALIPER TOOL SET 40732 ASSEMBLY AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from
More informationBucket Grease Pump ASSEMBLY AND OPERATING INSTRUCTIONS
Bucket Grease Pump 9793 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights
More informationLUBRICATOR ASSEMBLY AND OPERATING INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web site at
AIR FILTER, REGULATOR AND LUBRICATOR 40312 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2000 by Harbor Freight
More informationSEALER-15-1/2 ELECTRICAL IMPULSE
SEALER-5-/ ELECTRICAL IMPULSE OPERATING INSTRUCTIONS 39 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 000 by Harbor Freight Tools. All rights reserved.
More information25 GALLON PORTABLE OIL LIFT
25 GALLON PORTABLE OIL LIFT Model 92859 SET UP AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly
More information14.4 CORDLESS DRILL ASSEMBLY AND OPERATING INSTRUCTIONS
14.4 CORDLESS DRILL 40209 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2002 by Harbor Freight Tools. All
More information2 GALLON COOLANT PUMP
2 GALLON COOLANT PUMP Model 45333 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2001 by Harbor Freight Tools.
More informationSwing Back Trailer Jack
Swing Back Trailer Jack Model: 91474 ASSEMBLY AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly
More informationELECTRIC HYDRAULIC GEAR PUMP
ELECTRIC HYDRAULIC GEAR PUMP 46169 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2001 by Harbor Freight Tools.
More informationSquare Solar Garden Light 95706
Square Solar Garden Light 95706 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More information2 line price marking gun
2 line price marking gun Model 95878 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More information2-1/4 Gallon Sprayer
2-/4 Gallon Sprayer 94008 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 2005 by Harbor Freight Tools. All rights
More informationASSEMBLY and OPERATING INSTRUCTIONS Mission Oaks Blvd. / Camarillo, CA 93011
SPARK PLUG CLEANER ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 93011 Copyright 1997 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork
More informationCompressor Duty Motor - 1 HP. Model 40132
Compressor Duty Motor - 1 HP Model 40132 Assembly and Operating Instructions 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our web site at http://www.harborfreight.com Copyright 2002 by Harbor Freight
More informationSUBMERSIBLE PUMP. Model ASSEMBLY AND OPERATING INSTRUCTIONS
SUBMERSIBLE PUMP Model 37952 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools.
More informationALUMINUM JACK. 3,000 lb. Jack Capacity & JACK STAND COMBO. Model ASSEMBLY AND OPERATING INSTRUCTIONS
ALUMINUM JACK 3,000 lb. Jack Capacity & JACK STAND COMBO 6,000 lb. Jack Stand Capacity (when used in pairs) Model 91850 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011
More informationUTILITY WAGON WITH 1000 LB. CAPACITY
UTILITY WAGON WITH 1000 LB. CAPACITY 94908 ASSEMBLY & OPERATING INSTRUCTIONS Due to continuing improvement, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationPISTOL SHAPE SPOTLIGHT 500,000 CANDLE POWER ASSEMBLY & OPERATING INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA 93011
g ordon PISTOL SHAPE SPOTLIGHT 500,000 CANDLE POWER 4603 ASSEMBLY & OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Copyright 200 by Harbor Freight Tools. All rights reserved. No portion
More informationPROPANE TORCH WITH TURBO BURNER
PROPANE TORCH WITH TURBO BURNER MODEL 91894 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS INJURY,
More informationSIDE-WIND, A-FRAME TRAILER JACK. Model Due to continuing improvements, actual product may differ slightly from the product described herein.
SIDE-WIND, A-FRAME TRAILER JACK Model 95157 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationRio color changing solar light
Rio color changing solar light Model 95850 Assembly and operation instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationAIR COMPRESSOR 2 HP - 8 GALLON
AIR COMPRESSOR 2 HP - 8 GALLON 40400 ASSEMBLY & OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from
More information2 PIECE SOLAR LIGHT SET 93886
PIECE SOLAR LIGHT SET 93886 ASSEMBLY & OPERATING INSTRUCTIONS Due to continuing improvement, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA
More informationPropane torch. Model Assembly And Operation Instructions
Propane torch Model 39953 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA
More information1000 Lb. Motorcycle Lift
1000 Lb. Motorcycle Lift 91764 ASSEMBLY AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the
More information3 PC. SOLAR GARDEN LIGHT SET 92686
3 PC. SOLAR GARDEN LIGHT SET 92686 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web Site at www.harborfreight.com Copyright 2005 by Harbor Freight Tools. All
More informationOPERATING INSTRUCTIONS
8 FUNCTION DIGITAL MULTIMETER 90939 OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights
More informationANALOG SOUND LEVEL METER
ANALOG SOUND LEVEL METER 92282 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools.
More informationPOLISHER KIT Model 95030
3 PNEUMATIC POLISHER KIT Model 95030 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from
More informationCAMBELT TENSION GAUGE
CAMBELT TENSION GAUGE Model 96557 Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product
More informationDigital Auto Multi-Tester
Digital Auto Multi-Tester 95625 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 349 Mission Oaks Blvd., Camarillo,
More information6 OFF ROAD LIGHT BAR
6 OFF ROAD LIGHT BAR LOUD speaker Model 95953 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly
More informationPOWER INVERTER 1,000 WATT / 2,000 WATT PEAK
POWER INVERTER 1,000 WATT / 2,000 WATT PEAK 94009 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS
More information4-WHEEL CART ASSEMBLY INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web site at
4-WHEEL CART ASSEMBLY INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 003 by Harbor Freight Tools. All rights reserved. No portion of
More information1250 LB. CAPACITY MECHANICAL WHEEL DOLLY
1250 LB. CAPACITY MECHANICAL WHEEL DOLLY 67287 SET-UP AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result
More information1/2 Ton - 2 Stage Transmission Jack
1/2 Ton - 2 Stage Transmission Jack 34032 ASSEMBLY AND OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly
More informationModel Due to continuing improvements, actual product may differ slightly from the product described herein.
12 volt Oooga horn Model 96291 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More informationWelding Clips. Model Due to continuing improvements, actual product may differ slightly from the product described herein.
Welding Clips Model 95637 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA
More informationManual Operated Floor Jack
Manual Operated Floor Jack OPERATING INSTRUCTIONS Note: There may be some slight differences in the appearance of the various manually-operated floor jacks, however the instructions in this manual apply
More informationPUSH BUTTON KEY CABINET
PUSH BUTTON KEY CABINET Model 95689 INSTALLATION And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationTURTLE SOLAR LIGHT 94412
TURTLE SOLAR LIGHT 92 ASSEMBLY & OPERATING INSTRUCTIONS Due to continuing improvement, actual product may differ slightly from the product described herein. 39 Mission Oaks Blvd., Camarillo, CA 930 Visit
More informationFor technical questions and replacement parts, please call
Digital CLAMP MULTIMETER 42396 95652 OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA
More informationBATTERY OPERATED BI-PLANE
BATTERY OPERATED BI-PLANE 91311 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Website at www.harborfreight.com IMPORTANT: If damage is caused due to a crash,
More informationflexible infrared thermometer
flexible infrared thermometer Model 94233 assembly and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save Save This This Manual Keep Keep this this manual manual for for the the safety safety warnings warnings and and precautions, assembly, assembly, operating, inspection,
More informationSPECIFICATIONS GENERAL SAFETY RULES PERSONAL SAFETY. Save This Manual TOOL USE AND CARE WORK AREA
SPECIFICATIONS 2 Forged Safety Latch Hooks Cable extends to: 44 Drop forged steel hanging bracket Heavy duty 3/16 Steel Cable Pulling Capacity: 1200 LB. One piece double ratchet gear Save This Manual You
More informationManual Operated Floor Jack
Manual Operated Floor Jack OPERATING INSTRUCTIONS Note: There may be some slight differences in the appearance of the various manually-operated floor jacks, however the instructions in this manual apply
More informationp.t.o. Slip clutch Read this material before using this product. Failure to do so can result in serious injury. Save this manual.
p.t.o. Slip clutch 65517 Installation Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read
More informationMINI AIR ANGLE DIE GRINDER
MINI AIR ANGLE DIE GRINDER Model 33171 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More information4 in 1 solar bird bath
4 in 1 solar bird bath 66557 Set up and Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com
More information1200W Paint DRYING Lamp
1200W Paint DRYING Lamp Model 97641 Assembly And Operation Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from
More information4 color Solar light. Model Due to continuing improvements, actual product may differ slightly from the product described herein.
4 color Solar light Model 95665 Setup And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor
More informationSUBMERSIBLE MINI-PUMP
SUBMERSIBLE MINI-PUMP Model 41287 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More information4 AIR ANGLE GRINDER. Model ASSEMBLY AND OPERATING INSTRUCTIONS. Visit our website at:
4 AIR ANGLE GRINDER Model 95504 ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious
More informationMOTORCYCLE LIFT AIR OPERATED - 1,200 LB. CAPACITY. Model ASSEMBLY AND OPERATING INSTRUCTIONS. Visit our website at:
MOTORCYCLE LIFT AIR OPERATED - 1,200 LB. CAPACITY Model 94813 ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure
More informationCOIL SPRING COMPRESSOR CT1945
COIL SPRING COMPRESSOR CT1945 ORIGINAL INSTRUCTIONS INSTRUCTIONS It is important that you read and understand this instruction manual before using this product. You will need this manual for the safety
More informationCORDLESS 18V CIRCULAR SAW KIT
CORDLESS 8V CIRCULAR SAW KIT 374 ASSEMBLY and OPERATING INSTRUCTIONS www.harborfreight.com 349 Mission Oaks Blvd., Camarillo, CA 930 Copyright 997 by Harbor Freight Tools. All rights reserved. No portion
More informationELECTRIC LONG SHAFT DIE GRINDER 44141
ELECTRIC LONG SHAFT DIE GRINDER 44141 ASSEMBLY and OPERATING INSTRUCTIONS 1/4 Collet Accepts Most Popular Die Grinding Accessories Diagrams within this manual may not be drawn proportionally. Due to continuing
More informationbig foot panel wagon
big foot panel wagon Model 32826 assembly & Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious
More informationSUBMERSIBLE POND PUMP
SUBMERSIBLE POND PUMP 258 Gallons Per hour 47117 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2002 by Harbor
More informationANGLE DIE GRINDER KIT
ANGLE DIE GRINDER KIT Model 93157 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More informationPORTABLE KEY SAFE OPERATING INSTRUCTIONS
PORTABLE KEY SAFE OPERATING INSTRUCTIONS 39 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools. All rights reserved. No portion
More informationSPOTLIGHT 30 MILLION CANDLEPOWER
SPOTLIGHT 30 MILLION CANDLEPOWER 93175 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2005 by Harbor Freight
More informationrechargeable umbrella light
rechargeable umbrella light Model 98154 assembly And Operation Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationTWO POST LIFT 7,000 LBS.
R TWO POST LIFT 7,000 LBS. Model 46299 ASSEMBLY AND OPERATING INFORMATION 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2002 by Harbor Freight
More informationATD GALLON PRESSURIZED OIL DRAIN TANK
ATD-5203 30 GALLON PRESSURIZED OIL DRAIN TANK ASSEMBLY & OPERATING INSTRUCTIONS TECHNICAL SPECIFICATIONS Model: ATD-5203 Capacity: 30 Gallon Drain Funnel: Adjusts from 47.25 to 70.5 Drain Funnel Diameter:
More informationPNEUMATIC GARDEN STOOL
PNEUMATIC GARDEN STOOL 90473 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web Site at www.harborfreight.com 3 THANK YOU for choosing a HARBOR FREIGHT TOOLS product.
More informationBATTERY ISOLATOR. Model 93801: 70 Amp Model 93802: 90 Amp
BATTERY ISOLATOR Model 93801: 70 Amp Model 93802: 90 Amp Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011
More informationSolar mosquito killer
Solar mosquito killer Model 96415 Assembly And Operation Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious
More informationTWIN HALOGEN SHOP LIGHT
TWIN HALOGEN SHOP LIGHT 36787 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web Site at www.harborfreight.com Copyright 2005 by Harbor Freight Tools. All rights
More informationPOWER INVERTER 700 WATT / 1800 WATT PEAK
POWER INVERTER 700 WATT / 1800 WATT PEAK 91848 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS INJURY,
More informationAIRPLANE. Model Set up and Operating Instructions. Visit our website at:
AIRPLANE FREE Flying model Model 43678 Set up and Operating Instructions Visit our website at: http://www.harborfreight.com IMPORTANT: If damage is caused due to a crash, your warranty is void. Copyright
More informationMIG WELDER 131 ASSEMBLY AND OPERATING INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web site at
MIG WELDER 131 06098 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools. All rights
More informationAluminum Plus Low Profile Service Jack
Aluminum Plus Low Profile Service Jack Operating Instructions & Parts Manual Model Number ATD7344 ATD7345 Capacity 1.5 Ton 2.5 Ton Model ATD7344 Model ATD7345! This is the safety alert symbol. It is used
More informationSUBMERSIBLE PUMP 400 WATTS, WITH FLOAT Model 45019
SUBMERSIBLE PUMP 400 WATTS, WITH FLOAT Model 45019 ASSEMBLY and OPERATING INSTRUCTIONS Drain Water From Basements, Boats, Wells, Shafts, Containers and More! 3491 Mission Oaks Blvd., Camarillo, CA 93011
More informationSpecifications. Important Safety Information
Specifications Gauge Range 0-30 IN. of mercury (in Hg) 0-760 torr Important Safety Information WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow instructions listed below may result in serious
More informationTrailer Jack. Model Assembly and Operating Instructions
Trailer Jack Model 37792 Assembly and Operating Instructions 3491 Mission Oaks Blvd., Camarillo, CA 93011 Copyright 1998 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork
More informationELECTRONIC WHEEL BALANCER
ELECTRONIC WHEEL BALANCER Model 47211 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationTable of Contents. Safety... 2 Specifications... 3 Setup Parts List and Diagram Warranty Operation Maintenance
Table of Contents Safety Setup Operation Maintenance Safety... 2 Specifications... 3 Setup... 4 Operation... 5 WARNING SYMBOLS AND DEFINITIONS Maintenance... 9 Parts List and Diagram... 10 Warranty...
More informationPRESSURE WASHER WITH ROBIN 6 HP ENGINE
PRESSURE WASHER WITH ROBIN 6 HP ENGINE Model 91142 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ
More informationOPERATION MANUAL FOR BRAKE FLUID EXCHANGER
PRODUCT AND COMPANY IDENTIFICATION Product Name: Brake Fluid Exchanger GS-432 Product Use: Brake fluid exchanger Date of issue : 27.05.2012 Revision Date : 05.09.2013 Company Information: Sudheimer Car
More informationATD Gallon Pressurized Oil Drain Owner s Manual
ATD-5203 30 Gallon Pressurized Oil Drain Owner s Manual TECHNICAL SPECIFICATIONS Model: ATD-5203 Capacity: 30 Gallon Drain Funnel Working Height: 47.25 to 70.5 Drain Funnel Diameter: 15.75 Plastic Tray:
More informationSwing Arm Magnifying Lamp
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationAutomatic Emergency Light
Automatic Emergency Light Item 38013 Read this material before using this product. Failure to do so can result in serious injury. Save this manual. When unpacking, make sure that the product is intact
More information1000-LB. HYDRAULIC HOIST OWNER S MANUAL
1000-LB. HYDRAULIC HOIST OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious
More information18V RECIPROCATING SAW
V RECIPROCATING SAW 93830 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 349 Mission Oaks Blvd., Camarillo, CA
More informationPOND KIT WITH LINER 9 X 6
POND KIT WITH LINER 9 X 6 94945 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. To prevent serious injury, Read
More informationARTER AND DC POWER SOURCE
JUMPSTAR ARTER AND DC POWER SOURCE 91045 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 MISSION OAKS BLVD., CAMARILLO, CA 93011 VISIT OUR WEB SITE AT HTTP://WWW.HARBORFREIGHT.COM Copyright 2003 by Harbor Freight
More informationOPERATOR PROTECTIVE EQUIPMENT. Owner s Responsibility
CONGRATULATIONS! You have just made the first step toward making your tire changing chores much easier! This DAA Assist Arm assembly guide will help you to assemble and install your new DAA Assist Arm
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More information