SPV Series Slides OPERATING MANUAL. Table of contents 1 Introduction Compliance with the EC Directives Names of parts...

Size: px

Start display at page:

Download "SPV Series Slides OPERATING MANUAL. Table of contents 1 Introduction Compliance with the EC Directives Names of parts..."

Laurel McLaughlin
5 years ago
Views:

1 HL SPV Series Slides OPERATING MANUAL Thank you for purchasing an Oriental Motor product. This Operating Manual describes product handling procedures. Please read this Operating Manual and the separate manual entitled BEFORE USING THE PRODUCT thoroughly to ensure safe operation. Always keep the manual where it is readily available. Table of contents 1 Introduction Compliance with the EC Directives Names of parts Installation Motorized linear slides installation Installing a frame cover Installing a load Installing the sensor and sensor cable holder Connection Confirmation of controller key designation Connection of motor cable Inspection Inspection items and timing External check and cleaning Internal check/cleaning and greasing...9

2 1 Introduction 1 Introduction 1.1 Compliance with the EC Directives The SPV K slides bear the CE Mark indicating their compliance with the EMC Directive. The controllers combined with the SPV A and SPV C slides bear the CE Mark, but they do not conform to the EC Directives if combined with a motorized linear slides. Installation condition Overvoltage category SPV K Pollution degree 2 Protection against electric shock Noise level Environmental condition Ⅰ ClassⅢequipment 71 db Ambient temperature Ambient humidity Altitude Surrounding atmosphere Operation environment Storage environment Shipping environment 0 to +40 C (32 to +104 F) (non-freezing) 0 to +50 C (32 to +122 F) (non-freezing) 85% or less (non-condensing) -20 to +60 C (-4 to +140 F) (non-freezing) Up to 3000 m (10000 ft.) Up to 1000 m (3300 ft.) above sea level above sea level Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas) or liquid Area not exposed to direct sun Area free of excessive amount of dust, iron particles or the like Area not subject to splashing water (rains, water droplets), oil (oil droplets) or other liquids Area free of excessive salt Area not subject to continuous vibration or excessive shocks Area free of excessive electromagnetic noise (from welders, power machinery, etc.) Area free of radioactive materials, magnetic fields or vacuum EMC Directive EMC of SPV K has been measured in combination with a linear motion controller. Be sure to measure EMC of the applicable equipment after installing this product, by referring to Installing and wiring in compliance with EMC Directives in the Linear Motion Controller OPERATING MANUAL. Machinery Directive Motorized linear slides is designed and manufactured for use as an internal component for general industrial equipment, and therefore need not comply with the Machinery Directive. Nonetheless, they are evaluated under the following standards: Applicable Standards: EN ISO , EN ISO , EN 1050, EN

3 1 Introduction 1.2 Names of parts The figure shows the motor installed on top. The figure shows the slides with the frame cover, sensors and sensor cable holders attached. Motor Motor cable Frame cover Table Load mounting holes Positioning pin hole T-grooves -LS sensor HOME sensor Positioning pin hole (Long hole) Shielded plate Sensor cable holders +LS sensor -3-

4 2 Installation 2 Installation 2.1 Motorized linear slides installation Hexagonal socket head screws (included) Tightening torque: 5 N m (710 oz-in) Mounting plate Plate thickness Iron: 5 mm (0.20 in.) Aluminum: 10 mm (0.39 in.) If the motor is installed at bottom, make sure the motor does not contact the mounting surface. 2.2 Installing a frame cover Frame cover (included) Thin-head screws (included) Tightening torque: 0.6 N m (85.2 oz-in) 2.3 Installing a load Load SPV6 8 M5 Effective thread depth: 15 mm (0.59 in.) Tightening torque: 5 N m (710 oz-in) SPV8 8 M5 Effective thread depth: 20 mm (0.78 in.) Tightening torque: 5 N m (710 oz-in) Positioning pin hole (Pins cannot be press-fit.) -4-

5 2 Installation 2.4 Installing the sensor and sensor cable holder 1. Loosely affix the supplied pan-head screws on the sensor by making sure they do not project from the hexagonal nuts. Sensor (included) Hexagonal nuts (included) Pan-head screws (included) 2. Slide the hexagonal nuts on the sensor assembled in step 1, into the T-groove provided on the side of the frame. Motor side Sensor with hex nuts loosely tightened Frame section T-groove 3. Move the sensor to the recommended installation position, and then affix it in this position using the pan-head screws. Tightening torque: 0.6 N m (85.2 oz-in) SPV6 5 (0.20) 11 (0.43) (100 [3.94]) 10 (0.39) HOME sensor-detection -LS sensor-detection Mechanical limit Shielded plate Effective stroke of motorized linear slides +LS sensor-detection Mechanical limit [Unit: mm (in.)] 77.2 (3.04) 5 (0.20) -LS sensor HOME sensor 55 (2.17) 10 (0.39) +LS sensor 112 (4.41) Recommended sensor installation position The sensor and shielded plate can be installed on the side opposite to the one shown above. Tightening torque for installing the shielded plate: 1 N m (142 oz-in) -5-

6 2 Installation SPV8 5 (0.20) 10 (0.39) 11 (0.43) (120 [4.72]) Effective stroke of motorized linear slides [Unit: mm (in.)] 76.7 (3.02) 5 (0.20) HOME sensor-detection -LS sensor-detection Mechanical limit Shielded plate +LS sensor-detection Mechanical limit -LS sensor HOME sensor +LS sensor 65 (2.56) 10 (0.39) 120 (4.72) Recommended sensor installation position The sensor and shielded plate can be installed on the side opposite to the one shown above. Tightening torque for installing the shielded plate: 1 N m (142 oz-in) 4. Press in the sensor cable holders while paying attention not to pinch the sensor cables. Sensor cables Sensor cable holder (included) Frame section Note The connector for the sensor with cable is detachable, but do not detach/attach the connector while the power is supplied. It may damage the sensor. When removing the connector, do not pull it by the cables. Pull out the connector while pressing it firmly from the top and bottom. -6-

7 3 Connection 3 Connection Connect one end of the motor cable (sold separately) to the motor cable of the motorized linear slides, and connect the other end to the motor connectors on the controller. For the wiring of sensor cables, refer to 3.6 Wiring the sensor I/O and user I/O in the Linear Motion Controller OPERATING MANUAL. To controller's motor connectors Controller Motor cable SPV C SPV K SPV A To controller's sensor connectors Sensor cables indicates an optional accessory (sold separately). Must be soldered. 3.1 Confirmation of controller key designation Be sure to confirm that the motorized linear slides model shown on the controller key is the same as the model of the motorized linear slides connected to the controller. If the two do not match, the motorized linear slides cannot be operated according to the specification. When you purchased a motorized linear slides only, install the supplied controller key on a controller to be connected. For details, refer to Controller key in the Linear Motion Controller OPERATING MANUAL. Controller key Motorized linear slides model 3.2 Connection of motor cable Connect one end of the optional motor cable (sold separately) to the motor cable of the motorized linear slides (SPV K and SPV A have two connectors, while SPV C only has one connector). Affix each connector and place a cover, etc., to prevent the connector from moving or receiving excessive force. Note Insert each motor cable connector until the lock lever is securely affixed. -7-

8 4 Inspection 4 Inspection This chapter explains the maintenance items that must be performed to ensure safe, efficient operation of the motorized linear slides. Should you encounter any abnormality, immediately stop using the product and contact your nearest Customer Service Center. 4.1 Inspection items and timing Perform the inspections specified in the table below at the start of slides operation and after finishing the operation. Set an appropriate interval for post-operation inspection according to the utilization of the motorized linear slides. Inspection timing External check and cleaning Internal check When operated for the first time After operation 4.2 External check and cleaning Check the items specified in table below. Item What to check Action if problem is found Motorized linear slides Cables Operating Are there any loose mounting screws? Are there any damages or areas receiving stress? Are there any loose connections with the controller? Are there any abnormal noise or vibration from the bearings, etc.? Tighten the screws securely. Replace the damaged/stressed cable. Plug in the loose connector again. Check the installation of the load and operating speed again. Clean the exterior surface of the motorized linear slides whenever necessary. Wipe off any dirt and stains using a soft cloth. Do not apply compressed air to prevent dust from entering through gaps. Do not use petroleum solvents, since they will damage the coated surface. To remove stubborn stains, wipe the area using a soft cloth moistened with neutral detergent. -8-

9 4 Inspection 4.3 Internal check/cleaning and greasing Remove the frame cover to check and clean the internal parts. Note Before removing any component, clean the exterior surface first. If dust enters the motorized linear slides, the slides may generate noise during operation or suffer breakdown. 1. Loosen the thin-head screws and remove the frame cover. Frame cover Thin-head screws 2. Visual check of condition inside the motorized linear slides. Item What to check Action if problem is found Guide rail Are there any deposits of foreign matter such as dust? Has the grease lost its gloss or been consumed? Remove the foreign matter. Use a soft cloth to clean the ball rolling groove on both sides of the guide rail, and apply grease to the ball rolling grooves. Even if grease has turned brown, you need not add grease as long as the traveling surface looks slick. 3. Add grease. Grease has been applied before shipment. Use the grease specified below. Guide block Grease application position (Ball rolling groove) Guide rail: AFB-LF grease (THK CO., LTD.) Guide rail Guide 4. Install the frame cover, and affix it with the thin-head screws. Tightening torque: 0.6 N m (85.2 oz-in) -9-

10 4 Inspection -10-

12 Unauthorized reproduction or copying of all or part of this Operating Manual is prohibited. If a new copy is required to replace an original manual that has been damaged or lost, please contact your nearest Oriental Motor branch or sales office. Characteristics, specifications and dimensions are subject to change without notice. While we make every effort to offer accurate information in the manual, we welcome your input. Should you find unclear descriptions, errors or omissions, please contact the nearest office. and are trademarks of Oriental Motor Co., Ltd., and are registered in Japan and other countries. is a trademark of Oriental Motor Co., Ltd. Other product names and company names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. The third-party products mentioned in this manual are recommended products, and references to their names shall not be construed as any form of performance guarantee. Oriental Motor is not liable whatsoever for the performance of these third-party products. Copyright ORIENTAL MOTOR CO., LTD Please contact your nearest Oriental Motor office for further information. ORIENTAL MOTOR U.S.A. CORP. Technical Support Line Tel:(800) Available from 7:30 AM to 5:00 PM, P.S.T. techsupport@orientalmotor.com ORIENTAL MOTOR (EUROPA) GmbH Headquarters and Düsseldorf Office Tel: Fax: Munich Office Tel: Fax: Hamburg Office Tel: Fax: ORIENTAL MOTOR (UK) LTD. Tel: Fax: ORIENTAL MOTOR (FRANCE) SARL Tel: Fax: ORIENTAL MOTOR ITALIA s.r.l. Tel: Fax: TAIWAN ORIENTAL MOTOR CO., LTD. Tel:(02) Fax:(02) SINGAPORE ORIENTAL MOTOR PTE. LTD. Tel:(6745)7344 Fax:(6745)9405 ORIENTAL MOTOR (MALAYSIA) SDN. BHD. Tel:(03) Fax:(03) INA ORIENTAL MOTOR CO., LTD. KOREA Tel:(032) ~3 Fax:(032) ORIENTAL MOTOR CO., LTD. Headquarters Tokyo, Japan Tel:(03) Fax:(03) Printed on Recycled Paper

AZ Series Motor OPERATING MANUAL. Introduction. Safety precautions. CE Marking

AZ Series Motor OPERATING MANUAL. Introduction. Safety precautions. CE Marking HM-6244-3 OPERATING MANUAL Closed Loop Stepping and Driver Package AZ Series Introduction Before use Only qualified personnel should work with the product. Use the product correctly after thoroughly reading