315 & 317 TaperSeal Service Saddles Ductile Iron Body with Stainless Steel Straps ANSI/NSF 61 Listed
|
|
- Annis Harper
- 5 years ago
- Views:
Transcription
1 & TaperSeal Service Saddles Ductile Iron Body with Stainless Steel Straps ANSI/NSF Listed Protection Against Corrosion SmithBlair Engineers have taken the industry leading service saddle, the SmithBlair TaperSeal Saddle, and given it the additional benefit of corrosion resistance without changing its superior sealing, stability and pipe supporting qualities that have made it the preferred saddle. Here s what we do to make the SmithBlair TaperSeal Service Saddle exceptionally corrosion resistant: First, we shotblast the tough ductile iron saddle body down to bare metal; Next, we preheat the saddle; Then, we apply a heavy impact and corrosion resistant SmithBlair fusion bonded FlexiCoat epoxy coating; Next, we add job proven, selfenergizing Taper Seal gaskets and wide type 0 Stainless Steel Straps; Finally, we finish it off with type 0 Stainless Steel Bolts, Nuts and Washers. SmithBlair CC00 /0 Now, that s protection against corrosion! The same superior sealing and pipe supporting stability on the pipe, and the same easy installation qualities you have come to know and expect from the SmithBlair TaperSeal Service Saddles, are unchanged in the new corrosion protected saddles. Superior Sealing Qualities SmithBlair TaperSeal Service Saddles hold high pressure with just a few foot pounds of torque applied to the strap nuts. The unique, pressureenergized, TaperSeal gasket seals as a result of both mechanical and hydrostatic pressures and is held in position in a uniquely designed gasket cavity to provide optimum sealing efficiency. In laboratory testing, TaperSeal gaskets have been able to withstand pressures in excess of the working pressure of the pipe. When properly sized from the factory, SmithBlair TaperSeal Saddles meet the requirements listed in the UniBell PVC Pipe Association s Handbook of PVC Pipe and in the AWWA s Manual M: PVC Pipe Design and Installation. Nearly Full Pipe Support When installed on a pipe with an near the top of a saddle s range, the saddle body wraps around approximately 0 of the pipe. When installed on a pipe near the bottom of the saddle s range, the saddle wraps around approximately 0 of the pipe. As the strap bolts are tightened, tangential pull directs mechanical forces toward and around the pipe, uniformly distributing pressure around its circumference, supporting it and reinforcing it without a crushing action. Stability on the Pipe The wide skirt on SmithBlair TaperSeal Service Saddle bodies, combined with their wide wraparound stainless steel straps, provides excellent stability on the pipe. These two features work together to prevent the saddle from rocking or creeping on the pipe, which could be caused by vibration, pressure or excessive external loading. Easy to Install SmithBlair TaperSeal Service Saddles are designed for fast, easy installation. They feature a closed lug on one side of the saddle, which acts as a hinge and holds the bolt, nut and washer in place. The other side features an open canted lug, where the other bolt, nut and washer can be slipped, without disassembly. Thus, no loose parts get lost. In addition to their primary use for tapping pipe, the saddles may also be used to install air and vacuum valves, pitot tubes, or other equipment. They can also be used as pipe hangers or sign mounting brackets. Material Specifications BODIES: Ductile Iron ASTMA. BALES: For sizes. and smaller Type 0 Stainless Steel. STRAPS: For sizes. and larger Type 0 Stainless Steel. Single Strap Style.00 wide. Double Strap Style.0 wide. NUTS: Type 0 Stainless Steel Fluoropolymer Coated. WASHERS: Type 0 Stainless Steel. STUDS: Type 0 Stainless Steel /. GASKET: SmithBlair Nitrile (Buna N) NSF compounded to resist oil, acids alkalies, most (aliphatic) hydrocarbon fluids, water and many chemicals. (Contact SmithBlair engineers on applications involving chemicals). Temperature 0 F to 0 F. FINISH: Fusion bonded FlexiCoat Epoxy to a minimum thickness of mils. Material Specifications subject to change.
2 SmithBlair CC00 /0 /" CC/ /" CC/0 " CC/ // // * * * * * 0 * *0 * * * /" CC/ /" CC/0 " CC/ * * * * * 0 * * * * /, / and CC Taps /, / and CC Taps *d for Use on C00 PVC pipe. Service Saddles FlexiCoat Epoxy, Ductile Iron Body Double Strap Stainless Steel ANSI/NSF Listed
3 / and NPT Taps /" NPT/0 " NPT/ // // * * * * * 0 *0 0 * * *0 * * * * 0 *0 0 * * * Service Saddles FlexiCoat Epoxy, Ductile Iron Body Double Strap Stainless Steel ANSI/NSF Listed /, /, and / NPT Taps /" NPT/ /" NPT/0 " NPT/0 /" NPT/ When properly sized from the factory, this product meets the requirements listed in the UniBell PVC Pipe Association s Handbook of PVC Pipe and in the AWWA s Manual M: PVC Pipe Design and Installation. SmithBlair CC00 /0
4 Service Saddles FlexiCoat Epoxy, Ductile Iron Body Double Strap Stainless Steel ANSI/NSF Listed and NPT Taps " NPT/0 " NPT/ *0 0 * See 's page See 's page See 's page See 's page *d for use on C00 PVC pipe. Code Number Example /" /" " /" /" " /" BSP Thread Tap Codes 0 " NPT " BSP Certified to ANSI/NSF SmithBlair s unique, pressureenergized TaperSeal gaskets hold high pressures with just a few foot pounds of torque, to provide optimum sealing efficiency. When properly sized from the factory, this product meets the requirements listed in the UniBell PVC Pipe Association s Handbook of PVC Pipe and in the AWWA s Manual M: PVC Pipe Design and Installation. SmithBlair CC00 /0
5 Service Saddles General Information. Initial tightening confines the TaperSeal gasket in the gasket cavity. During continued tightening, the canted ears on the saddle body and angular shape of the bales cause a tangential pull that forms the body casting to the pipe, directing mechanical forces toward and around the pipe to support and reinforce it. If the saddle body is not initially loose on the pipe, it should be spread before installation.. Tightening is complete when the saddle body conforms to the pipe. No additional benefit results from overtightening the saddle.. Service Saddle gaskets are glued in for convenience in handling. The glue does not improve the performance of the saddle. Should the gasket come loose, simply position it in the saddle body and continue with installation.. It is a good practice to screw the corporation stop, or other fitting being used, into the service saddle before mounting the saddle on the pipe. Doing so protects the threads from damage or distortion during installation and verifies that the fitting is the correct size and thread type.. Service saddles should be initially placed, as near as possible to their exact final location on the pipe. Excessive moving of the saddle on the pipe could damage the rubber gasket.. There are two types of threads coonly furnished on service saddles in the United States and Canada; a standard pipe thread and a special waterworks thread developed for service connections that have a steeper taper than the standard pipe thread. Some coon designations for these types of threads are: Standard Pipe Thread: NPT National Pipe Thread IP Iron Pipe IPS Iron Pipe IPT Iron Pipe Thread Pipe Thread Standard Pipe Thread Waterworks Thread: CC Corporation Cock CS Corporation Stop AWWA American Water Works Association Corporation Corp Copper Service Mueller In Europe, some areas of the Caribbean, and some other locations, BSP (British Standard Pipe) threads may be used. The technical performance data, specifications and recoendations in this bulletin are intended as a reference for the utilization of SmithBlair clamps and couplings by piping designers, installers and owners, and maintenance personnel. Many situations have special conditions, requiring the expertise of qualified personnel who must make the decision regarding application. The material presented here is not intended as a substitute for professional assistance. Pressures, temperatures and other performance standards stated herein should never be exceeded. Although an extra effort has been made to insure the accuracy of this material, SmithBlair makes no express or implied warranties regarding the information or materials contained in this bulletin. Anyone making use of this information assumes all liability resulting from such use. SmithBlair, Inc. 0 Globe Avenue Texarkana, AR P.O. Box Texarkana, TX 0 Phone:(00) 0 (0) Fax:(00) (0) SmithBlair CC00 SWP/00 /0
Smith-Blair OMNI Coupling System Advantages:
OMNI Coupling System SmithBlair s OMNI Coupling System utilizes the tremendous tensile strength of ductile iron to your best advantage. Applying the principles of space age technology to engineer the OMNI
More informationHeavy welded steel outlet half. 3/4-inch NPT test plug. Benefits
622 Tapping Sleeve Recessed cavity for mating to lip on standard tapping valves per MSS SP60. Heavy welded steel outlet half. 3/4-inch NPT test plug. Roll resistant, self-energizing concave wedge gasket.
More informationPipe Size Pipe OD TwinSeal Hinged Design for IPS PVC Pipe MODEL 3402 BRONZE SADDLE FOR COPPER TUBING
MULTIPLIER SERVICE SADDLES MODEL 3401 BRONZE SADDLE FOR IPS PVC BODY CASTINGS: Waterworks Bronze (85-5-5-5) per ASTM B584 and AWWA C800. FASTENERS: Silicon Bronze per ASTM B98. GASKET: Patented SBR TwinSeal
More informationFord Service Saddles and Tapping Sleeves
DQS Inc. Section AA 09/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Ford Service Saddles and Tapping Sleeves Contents Recommended Product Application *Steel *C900/909*** Cast
More informationFord Brass Saddles Style 101B and 202B
101B Ford Brass Saddles 101B and 202B 101B, 3/4" and 1" Taps 202B, 3/4" through 2" Taps Specifications Body - 85-5-5-5 brass alloy as per ASTM B62, ASTM B584 and AW WA C800. Threads may be FIP, AW WA,
More informationFord Service Saddles and Tapping Sleeves
Section AA 04/2013; web revision 02/2014 Ford Service Saddles and Tapping Sleeves The Ford Meter Box Company, Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171
More informationTAPPING & SERVICE SADDLES
TAPPING & SERVICE SADDLES The Standard of Excellence in the Industry CS12 CSC1 CS22 CSC2 CNS1 CDS1 CNS2 CDS2 CFS CFT-TO 1213 BADGER STREET YORKVILLE, ILLINOIS 60560 (630) 553-0840 (800) 426-4301 FAX (630)
More informationFITTINGS AND FABRICATIONS DESIGNED AND ENGINEERED HIGH DENSITY POLYETHYLENE PIPE
Effective May 24, 2002 Cancels all previous publications U.S. Price $12.95 FITTINGS AND FABRICATIONS DESIGNED AND ENGINEERED FOR HIGH DENSITY POLYETHYLENE PIPE JCM Industries, Inc. P.O. Box 1220 Nash,
More informationROMAC INDUSTRIES, INC. WIDE RANGE RESTRAINT. RESTRAINED END CAP page 6-7 NOW AVAILABLE FOR HDPE PIPE NO STIFFENER REQUIRED
ROMAC INDUSTRIES, INC. WIDE RANGE RESTRAINT RESTRAINED COUPLING page 4-5 RESTRAINED END CAP page 6-7 RESTRAINED FLANGED COUPLING coming soon JUNE 2014 UPDATE NOW AVAILABLE FOR HDPE PIPE NO STIFFENER REQUIRED
More informationPipe Repair Products. A complete selection for all types of pipe
Pipe Repair Products A complete selection for all types of pipe Mueller Service Saddles Manufactured and tested in accordance with ANSI/AWWA C800 & NSF 61 certified. Mueller service saddles, available
More informationSteel Fabricated Coupling
Steel Fabricated Coupling Straight Connection IMPORTANT LINKS Click appropriate words to go to: Standard Limited Warranty Sales Terms & Conditions Freight Policy Returns Policy Corrosion & Product Selection
More informationJ & S Valve GATE VALVE AWWA C509. Resilient Seated Solid Wedge Size: 2-12
J & S Valve GATE VALVE Resilient Seated Solid Wedge Size: 2-12 AWWA C509 Resilient Seated Solid Wedge Gate Valve Series 6000 AWWA C509 2 Operating Nut or Hand Wheel Stem Stainless Steel or Bronze Gland
More informationSERVICE SADDLES & Cambridge Brass Inc. 140 Orion Place, Cambridge, Ontario, N1R 5V1, Canada
SERVICE SADDLES & TeCK TM Repair Clamps Cambridge Brass Inc. 140 Orion Place, Cambridge, Ontario, N1R 5V1, Canada www.cambridgebrass.com 2014 Cambridge Brass Inc. FEBRUARY2014 CAMB2014 TABLE OF CONTENTS
More informationService Materials. Service Materials. With Three Locations to Serve You: Avoca, NY 8125 Kanona Rd. Avoca, NY (607)
Service Materials Service Materials Rochester, NY 785 Beahan Rd. Rochester, NY 14624 (585) 436-9624 With Three Locations to Serve You: Avoca, NY 8125 Kanona Rd. Avoca, NY 14809 (607) 566-2214 Watertown,
More informationLineseal Butterfly Valves 150B, 250B, & 350B Class; Sizes 3-48
Lineseal Butterfly Valves 0B, 0B, & 0B Class; Sizes -8 Mueller Lineseal Butterfly Valves Sizes -8 Performance is key. Designed specifically for the waterworks industry, Lineseal butterfly valves offer
More informationFord Fabricated Steel Products
Ford Fabricated Steel Products Section N2 12/2000 The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 219/563-3171 FAX: 1-800-826-3487 Overseas
More informationTOTAL PIPING SOLUTIONS, INC. TRIPLE-TAP
TOTAL PIPING SOLUTIONS, INC. TRIPLE-TAP Extended Range Stainless Steel Push Plug Line Stop Tapping Sleeve Technical Specifications Controlled Document: ENGTS-05/120417 December 2017 TRIPLE TAP Extended
More informationUNION-TITE DUCTILE IRON C153 COMPACT FITTINGS
Sizes 4"-12" UL Listed for Fire Main Equipment SAMPLE SPECIFICATIONS (Current ANSI/AWWA revisions apply) 4" through 24" Push-On joint ductile iron fittings shall be produced in accordance with all applicable
More informationThe Number One Choice of Line Stopping Contractors
JCM 0 Line Stop Fittings Take a Look!!! JCM 0 FAMILY OF LINE STOP FITTINGS HAS EPANDED New Plug Option - New Numbering System Whatever your application needs, JCM has it! JCM Industries offers the largest
More informationSection 8 AMERICAN. Flanged Pipe
Section 8 AMERICAN Flanged Pipe The principal standards covering Flanged Pipe are ANSI/AWWA C115/A21.15 and ANSI/AWWA C110/A21.10. These and other standards are referenced throughout this Section either
More informationApproved Branded Traceable Fire Protection & Waterworks Valves
Approved Branded Traceable Fire Protection & Waterworks Valves (800) 766-0076 www.smithcooper.com Los Angeles, CA Atlanta, GA Vancouver, WA Chicago, IL AWWA C515 Compliant CONSIDER Your Options Tamper
More informationButterfly Valve. Product Training Presentation Danfoss Flomatic Corporation
Click to see: Butterfly Valves in our Online Catalog Butterfly Valve Product Training Presentation Danfoss Flomatic Corporation REV:082303 Butterfly Valve SYLAX SERIES 149G BUTTERFLY VALVES Wafer and Lug
More informationNEW FROM JCM INDUSTRIES MODEL 161 FABRICATED LUG ALL STAINLESS STEEL CLAMP
JCM 161 FABRICATED LUG ALL STAINLESS NEW FROM JCM INDUSTRIES MODEL 161 FABRICATED LUG ALL STAINLESS STEEL The new JCM 161 Fabricated Lug All Stainless Steel Clamp offers an economical solution to problems
More informationSWING CHECK VALVES SERIES 52-SC SERIES 600
SWING CHECK VALVES SERIES 52-SC SERIES 600 FEATURES/BENEFITS/SPECIFICATIONS AMERICAN Flow Control Series 52-SC Swing Check Valves incorporate design features to help increase service life for water and
More informationSection N. 09/2017 Web Revision 10/23/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001: Ford Fabricated Steel Products
DQS Inc. THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Section N 09/2017 Web Revision 10/23/2017 Ford Fabricated Steel Products Contents Page Product Numbering System... 3 Information...............................................................
More informationINFACT CORPORATION WATERWORKS PRODUCTS FLEX ADAPTOR SPECIFICATION S TOLL FREE:
INFACT CORPORATION WATERWORKS PRODUCTS SPECIFICATION S TOLL FREE: 888-773-9130 email: info@infactcorp.com www.infactcorp.com ENGINEERING DATA / PRODUCT CHECKLIST EASY-TO-INSTALL SPACE-SAVING RESTRAINT
More informationFord Bolted Flex Couplings. Section M. 5/2008; Web Revision 10/2010
Section M 5/2008; Web Revision 10/2010 Ford Bolted Flex Couplings The Ford Meter Box Company, Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171 FAX: 800-826-3487
More information516509_tabs 11/16/10 4:55 AM Page 1 FIRE HYDRANTS
Date Printed: November 2010 FIRE HYDRANTS or Tyton (6"),6, or 8" A EDDY FIRE HYDRANTS PARTS LIST WORKING PRESSURE: 150 PSI Note: Discontinued For Reference Only 350 PSI Working Pressure
More informationTABLE OF CONTENTS. Pipe Diameter Chart (Reference Only)..50 Extensions 38,40,42,44
TABLE OF CONTENTS Item Page Item Page ANSI/AWWA Compact & Full Body Pipe Fittings: Product Submittals and Installation: Mechanical & Flange Joint C153. 3-9 20U Protective Fusion Bonded Epoxy....5,5 Mechanical
More informationMACRO HP. NEW SMALLER SIZES Macro HP is Now Available for 2-12 inch Pipe Sizes. patent number:
ACROMACROMACROMA MACRO HP ROMAC S SECOND GENERATION TWO-BOLT E X T E N D E D R A N G E C O U P L I N G NEW SMALLER SIZES Macro HP is Now Available for 2-12 inch Pipe Sizes patent number: 8448993 BMACROHP
More informationPROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
More informationAMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE
AMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE CONSTRUCTION STAINLESS STEEL PIPE PLUG Allows installation of pressure gauge. STAINLESS STEEL FASTENERS Helps provide corrosion resistance.
More informationIron Check Valves Illustrated Index
Iron Check Valves Illustrated Index Iron Body Swing Check Valve Bronze Mounted or All Iron 125 lb. SWP 200 lb. CWP Iron Body Swing Check Valve Bronze Mounted 250 lb. SWP 500 lb. CWP Iron Body Silent Check
More informationGENERAL FEATURES / SPEC M&H AWWA C502 FIRE HYDRANTS Style 929 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approval Type: Compression type, opening against line pressure.
More informationFLOAT CONTROL VALVES
PROJECT NAME LOCATION FLOAT CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 8 in. (200 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL 1. Standard
More informationEXPECT RELIABILITY AVK RESILIENT SEATED GATE VALVES
EXPECT RELIABILITY AVK RESILIENT SEATED GATE VALVES AVK VALVES STANDARD FEATURES AVK STANDARD FEATURES AVK Gate Valves are made of ductile iron and meet or exceed AWWA C509 or C515 ASTM A582 stainless
More informationHYMAX GRIP by Krausz Restraint Solutions
HYMAX GRIP by Krausz Restraint Solutions HYMAX GRIP. THE TEETH MAKE THE DIFFERENCE. There are many situations that require couplings with additional restraining power. Krausz restraint products combine
More informationMueller Super Centurion 250 Fire Hydrant
Mueller Super Centurion 250 Fire Hydrant Designed for efficient flow and outstanding, long-term reliability Mueller Super Centurion 250 Fire Hydrant...250 psig rating, high flow, dependable performance,
More information411 Steel Couplings Material Specifications
411 Steel Couplings Material Specifications Gasket Material Specifications STANDARD: Nitrile (Buna-N)-NSF 61 Compounded to produce superior storage and performance characteristics while resisting water,
More informationAWWA Swing Check Valves
AWWA Swing Check Valves Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the
More informationSERIES CVI AWWA C508 SWING CHECK VALVES 2-48
SERIES CVI AWWA C508 SWING CHECK VALVES -48 508-103 R0 June 018 LIFTING LUGS & ACCESSORY HOLE VSI check valve covers come standard with stainless steel lifting lugs for ease of install and movement in
More informationALTITUDE CONTROL VALVES FOR ONE WAY FLOW
PROJECT NAME LOCATION ALTITUDE CONTROL VALVES FOR ONE WAY FLOW INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1
More informationJCM 101 Universal Clamp Couplings
JCM 1 Universal Clamp Couplings JCM 1 Universal Clamp Coupling - Single Band JCM Universal Clamp Couplings provide a full circumferential seal and wide range for the permanent repair or reconnection of
More informationSeptember 2012 / M&H C502 / Model 129
GENERAL FEATURES / GENERAL SPEC M&H AWWA C502 FIRE HYDRANTS Model 129 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approved Type: Compression type, opening against line
More informationWide-Range Coupling Solutions
Wide-Range Coupling Solutions HYMAX. CONNECTING THE FUTURE. A revolutionary product that set a new industry standard, the HYMAX* product line has been field-proven in millions of installations world-wide.
More informationMODULATING FLOAT CONTROL VALVE
PROJECT NAME LOCATION MODULATING FLOAT CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL
More informationHYMAX VERSA by Krausz Coupling and Repair Solutions
HYMAX VERSA by Krausz Coupling and Repair Solutions HYMAX VERSA. VERSATILE STAINLESS STEEL COUPLING. Krausz HYMAX VERSA products provide a highly versatile stainless steel coupling solution for connecting
More informationPRESSURE REDUCING CONTROL VALVES
PROJECT NAME LOCATION PRESSURE REDUCING CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL
More informationPRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE
PROJECT NAME LOCATION PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2-1/2 in. (65 mm) through 18 in. (450 mm) Control
More informationCCNE Check Valves Engineering Creative Solutions for Fluid Systems Since 1901
CCNE Check Valves Engineering Creative Solutions for Fluid Systems Since 1901 A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry
More informationSentinel 250 Fire Hydrant. Solid design and features to meet any municipal requirement.
Sentinel 250 Fire Hydrant Solid design and features to meet any municipal requirement. Product Features That meet any municipal requirement. 1 Operating Nut Shields the hold down nut from tampering and
More informationSAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class 150/250 December 2012
SAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class December 2012 1. SCOPE This product specification covers class rubber-seated butterfly
More informationRed Thread IIA Primary Fittings (Product Data)
Red Thread IIA Primary Fittings (Product Data) FUEL HANDLING 90 and 45 Elbow, Flange and Tee Pipe Size A B C D E F O X 1 X 2 in mm in mm 2 50 3 3/8 86 2 1/4 57 3/4 19 4 3/4 121 3/4 D-4 Holes 19 D-4 Holes
More informationUtilities Catalog. PC-U2008, February, 2008
Utilities Catalog PC-U2008, February, 2008 Tyler Utilities 11910 CR. 492 Tyler, Texas 75706 (800) 527-8478 Union Foundry Company Box 309 Anniston, Alabama 3602 (800) 226-7601 TABLE OF CONTENTS Item Page
More informationAmerican Flow control 5 1/4 B-62-B-5
American Flow control 5 1/4 B-62-B-5 Fire Hydrant FLOW CONTROL Construction Fully complies with AWWA C502 and is available UL Listed and FM Approved in applicable configurations. one-piece bronze OPERATING
More informationAMERICAN FLOW CONTROL 5 1/4 B-84-B-5 FIRE HYDRANT
AMERICAN FLOW CONTROL 5 1/4 B-84-B-5 FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available Listed by Underwriters Laboratories, Inc. and Approved by FM Approvals in applicable configurations.
More informationAMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT
AMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available Listed by Underwriters Laboratories Inc. and Approved by FM Approvals in applicable
More informationPRESSURE RELIEF / SUSTAINING CONTROL VALVES
PROJECT NAME LOCATION PRESSURE RELIEF / SUSTAINING CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900 mm) Control Valves PART
More informationSeries 800 AWWA Butterfly Valves
Series 800 AWWA Butterfly Valves Valve and Gate Group A Century of Experience GA valves are known for long term reliability in the most demanding water and wastewater applications. Whether a simple check
More informationSuper Flange series 7200 Designed for use on Ductile Iron, Steel, PVC, PVCO and HDPE Pipes
Designed for use on Ductile Iron, Steel, PVC, PVCO and HDPE Pipes INFORMATION The Series 7200 Super Flange is a restrained flange adapter designed to connect plain end pipe to a flange end component. May
More informationCompression Fittings & Valves. Make the connection
Compression Fittings & Valves Make the connection Make the Connection with Compression Fittings, Valves, and Municipal Stops Make the connection with Philmac fittings. The versatile Philmac fitting system
More informationCLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION
CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION TESTING AND DESIGN SPECIFICATIONS (PER AWWA C502 / NSF /ULC & FM) 1. Hydrant shall be manufactured in accordance with AWWA C502 latest revision
More informationSOLENOID CONTROL VALVE
PROJECT NAME LOCATION SOLENOID CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 4 in. (100 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL 1. Standard
More informationDENSITY POLYETHYLENE PIPE
Effective January 15, 2016 Replaces 9/2/10 U.S. Price $14.00 JCM INDUSTRIES Fittings and Fabrications Designed and Engineered for HIGH DENSITY POLYETHYLENE PIPE HDPE JCM Industries, Inc. P. O. Box 1220
More informationPRESSURE REDUCING CONTROL VALVE
PRESSURE REDUCING CONTROL VALVE 06/08 Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) X P/L Standard Components 1 Main
More informationSERIES GVI AWWA C509/C515 RESILIENT SEATED GATE VALVES 2-48
SERIES GVI AWWA C509/C515 RESILIENT SEATED GATE VALVES 2-48 509-110 R6 OCT 2018 REPLACEABLE 0-RINGS Triple O-ring sealed with upper two O-rings replaceable with the valve fully open and subjected to the
More informationSECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3
SECTION VIII (Sub-section 430) Wastewater Valves and Appurtenances Article Page 1. General 430-1 thru 430-2 2. Gate Valves 430-2 thru 430-3 3. Plug Valves 430-3 thru 430-4 4. Check Valves 430-4 5. Tapping
More informationTHOMAS. Ultra Saddles & Tees. Tap In Products PIPE PRODUCTS. Full Circle Stainless Steel Repair Saddle Clamps and Tee Clamps
THOMAS PIPE PRODUCTS Tap In Products Ultra Saddles & Tees Full Circle Stainless Steel Repair Saddle Clamps and Tee Clamps E1 Ultra Saddles & Tees Overview For a Permanent and Simple Tap In Solution for
More informationVal-Matic 3-Way Tapered Plug Valve
Val-Matic 3-Way Tapered Plug Valve Manual No. CCPV-OM4-1 Operation, Maintenance and Installation Manual INTRODUCTION.2 RECEIVING AND STORAGE 2 VALVE CONSTRUCTION..2 DESCRIPTION OF OPERATION. 3 INSTALLATION
More informationPVC Pressure Piping Systems for Water Transmission
PVC Pressure Piping Systems for Water Transmission MUNICIPAL SYSTEMS PVC PRESSURE PIPING SYSTEM MANUFACTURED TO AWWA & CSA STANDARDS IPEX Centurion 14" 60" (350mm 1,500mm), AWWA C905 and CSA Standards
More informationMustang Series PRESSURE REDUCING CONTROL VALVE. M115 (Globe) M1115 (Angle) Schematic. Standard Components. Options & Accessories.
PRESSURE REDUCING CONTROL VALVE 02/09 Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) P/L Standard Components 1 Main Valve
More information5 1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT BY AMERICAN FLOW CONTROL
5 1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT BY AMERICAN FLOW CONTROL CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and FM Approved in applicable configurations. ONE-PIECE
More information1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service.
KENNEDY KENNEDY VALVE MODEL VALVE KS-RW 1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service. 2. The valves shall have a cast
More informationAmerican Flow control 5 1/4 b-84-b-5
American Flow control 5 1/4 b-84-b-5 Fire Hydrant FLOW CONTROL Construction Fully complies with AWWA C502 and is available UL Listed and FM Approved in applicable configurations. one-piece bronze OPERATING
More informationHawle Haku PE Pipe Saddle
Hawle Haku PE Pipe Saddle Scan for more information Technical Guide W9.1 Specifically designed as a PE mechanical connection solution. Suitable for PE pipes of all pressure ratings up to PN 16. DN40-360.
More informationGRINNELL Model B302 and Model BN302 Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description
Worldwide Contacts www.grinnell.com GRINNELL Model B0 and Model BN0 Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description The GRINNELL Model B0 and Model BN0 Butterfly
More informationCOMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES 2.01 COMBINATION RESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVE
PROJECT NAME LOCATION COMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900
More informationHP 16 Epoxy Fittings (Filament wound with reinforced epoxy inner liner - Compatible with Red Thread and Green Thread HP 16 piping systems)
HP 16 Epoxy Fittings (Filament wound with reinforced epoxy inner liner - Compatible with Red Thread and Green Thread HP 16 piping systems) CHEMICAL INDUSTRIAL Fiber Glass Systems provides a broad range
More informationFlexible Couplings & Saddles
Revised 6/01 Flexible Sewer couplings are the result of many years of experience with sewer pipe connections. Today's couplings are made of specially formulated elastomeric PVC with high tear and shear
More informationMueller 300 Ball Valves Industry-leading 300psi low lead ball valves
Mueller 300 Ball Valves Industry-leading 300psi low lead ball valves Mueller 300 Ball Valves Your assurance of quality, dependable ball valves The ball valve designed for 300 psig working pressure Before
More informationMUELLER Super Centurion fire hydrants
MUELLER Super Centurion fire hydrants MUELLER SUPER CENTURION FIRE HYDRANT Since its introduction in 1976, millions of Centurion fire hydrants have been installed throughout the world. There are a number
More informationAWWA SWING CHECK VALVES. Engineering Creative Solutions for Fluid Systems Since 1901
AWWA SWING CHECK VALVES Engineering Creative Solutions for Fluid Systems Since 1901 TABLE OF CONTENTS AWWA SWING CHECK VALVE Series 8001 Lever & Weight or Spring...1 Series 9001 Lever & Weight or Spring...2
More informationPRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve
More informationPRICE SHEET TABLE OF CONTENTS AWWA VALVES & HYDRANTS. (PL-0418-AWWA Replaces PL-1014-VLV)
Page(s) 1 2 3 3 4 4 5 5 6 PRICE SHEET TABLE OF CONTENTS VALVES & HYDRANTS ( Replaces PL-1014-VLV) Product Line C515 NRS Gate Valves Series 1010 UL/FM C515 NRS Gate Valves Series 2010 C508 Swing Check Valves
More informationPRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve
More informationLEAD FREE * LFF113RFP Wireless Smart Flood Protection Shut Down Valve with SentryPlus Alert Technology
Technical Bulletin TB-ACV-LFF11RFP_SentryPlus LEAD FREE * LFF11RFP Wireless Smart Flood Protection Shut Down Valve with SentryPlus Alert Technology Installed upstream of Reduced Zone Backflow Preventer.
More informationLEAD FREE * LFF113RFP Flood Protection Shut Down Valve
Technical Bulletin TB-ACV-LFF11RFP LEAD FREE * LFF11RFP Flood Protection Shut Down Valve Installed upstream of Reduced Zone Backflow Preventer. Normally Open Valve - Closes when continuous discharge from
More informationPRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Closes quickly when downstream pressure exceeds reduced pressure setpoint 3 PRESSURE REDUCING VALVE with SURGE
More informationAMERICAN FLOW CONTROL 5 1/4 B-62-B-5 FIRE HYDRANT
AMERICAN FLOW CONTROL 5 1/4 B-62-B-5 FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and Approved by FM Approvals in applicable configurations. ONE-PIECE BRONZE
More informationStyle 234 Restrained Flexible Single-Gasket Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date
Victaulic Bolted Split-Sleeve Products (VBSP) Style 234 carbon steel couplings (formerly Depend-O-Lok Air/FluidMaster) are single-arch couplings that are commonly used in buried or exposed steel pipe applications
More informationAWWA C 504 Type - Butterfly Valves AWWA C 504 BUTTERFLY VALVES
AWWA C 504 BUTTERFLY VALVES 19 PRODUCT FEATURES: NSF Certified Fusion Bonded Epoxy Coating and EPDM rubber are used for valves to be used for in direct contact with potable (drinking) water, while all
More informationHarlingen Water Works System Approved Products List For Subdivisions. January 11, 2005
Harlingen Water Works System Approved Products List For Subdivisions January 11, 2005 Revised March 24, 2016 Harlingen Water Works System Approved Products List for Subdivisions Table of Contents: 1. Valves
More informationAMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT
AMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and Approved by FM Approvals in applicable configurations. DUCTILE IRON
More informationGrinnell Grooved Fire Protection Products Grooved Fittings
Technical Services: Tel: (800) 38-932 / Fax: (800) 79-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Grooved Fittings General Description LPCB Vd S The grooved fittings provide an economical
More informationROMACON COUPLINGS AND FLANGE ADAPTORS
ROMACON COUPLINGS AND FLANGE ADAPTORS Couplings DN mm DN inches Range Romafit Weight kg 50 2 59-73 3,8 65 2,5 72-85 4,3 80 3 88-103 4,5 100 4 108-128 5,6 125 5 132-146 6,8 125 5 139-153 6,9 150 6 159-182
More informationHYMAX GRIP Wide-Range Restraint Solutions
HYMAX GRIP Wide-Range Restraint Solutions HYMAX GRIP. THE TEETH MAKE THE DIFFERENCE. There are many situations that require couplings with additional restraining power. HYMAX restraint products combine
More information2-inch operating nut (other options available) 10 millimeter fusion-bonded epoxy coating (NSF-61) Triple O-ring seal
InsertValve The Team InsertValve TM is a fully functioning, resilient wedge gate valve with a rated working pressure of 250 psig. The valve fully closes, and it provides a clear, unobstructed waterway
More informationAVK SERIES 41 SWING CHECK VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR SWING CHECK VALVES 3" - 12"
AMERICAN AVK COMPANY AVK SERIES 41 SWING CHECK VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR SWING CHECK VALVES 3" - 12" TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION
More informationTYLER UNION. Quality Waterworks Products. PC-2017, March, REGISTERED FIRMISO 9001:2015. Tyler Union
TYLER UNION Quality Waterworks Products WATERWORKS CATALOG PC-2017, March, 2017 www.tylerunion.com 10014257 U L REGISTERED FIRMISO 9001:2015 CERTIFIED Tyler Union 11910 CR 492 TYLER, TEXAS 75706 (800)
More informationApproved. Size L H. 3" (76mm) 9-1/2" (241mm) 5-51/64" (147mm) 46. 4" (102mm) 11-1/2" (292mm) 6-45/64" (170mm) 81
pproved. Model: SD-NRV200CV Flanged Ends The Flanged End Check Valves are made of Iron Body, Bolted Bonnet and Horizontal Swing, painted with standard color. Epoxy coated inside and outside to WW C550
More information