AV series Anti-vandal and security pushbutton switches
|
|
- Abigayle Glenn
- 5 years ago
- Views:
Transcription
1 Anti-vandal and security pushbutton switches Distinctive features Attractive, robust and durable Irremovable Anti-jamming construction : reduced travel to prevent insertion of foreign parts and mechanism protected against crushing Fire resistant Long life Sealed versions Degree of protection (switches mounted on vertical panels, as shown opposite) : - standard version : IP54 - sealed version : IP65 EXAMPLES OF MOUNTING FOR SEALED VERSIONS O-ring Preferred With boot U187 (sect. H) Packaging unit : specified on the following pages. Mounting accessories : Standard and special hardware are presented in section I APEM
2 Anti-vandal and security pushbutton switches Distinctive features The AV series is a large range of security pushbutton switches including 4 product families : ANTI-VANDAL PUSHUTTON SWITCHES (page -90) Increased impact resistance provided by a nut (Ø 19 mm) or mechanical stop (Ø mm) Stainless steel actuator and bushing ushing dia. 19 (.748) or mm (.866) SECURITY PUSHUTTON SWITCHES WITH LARGE ACTUATOR (page -93) Ergonomic actuator dia. 0 (.787) or 30 mm (1.181) Tactile feedback Up to 5A 50VAC ushing dia. mm (.866) or 4 mm (.944) OTHER SECURITY PUSHUTTON SWITCHES (page -96 ) A large variety of actuator shapes, electrical functions, connections, finish and marking options ushing dia. 16 (.69), 19 (.748) or mm (.866) SNAP-ACTION SECURITY PUSHUTTON SWITCHES (page -104) Tactile feedback Illuminated or non-illuminated ushing dia. 19 mm (.748) Models with overmolded actuator APEM -89
3 Anti-vandal pushbutton switches Distinctive features and specifications Increased impact resistance provided by a nut or mechanical stop Stainless steel actuator and bushing UL-CSA approved (long case only) SPECIFICATIONS Max. current/voltage rating with resistive load (C contacts) : A 48 VDC Approved ratings of models with long case and A contacts (AV..000) : UL-CSA : 4A 50VAC - 8A 15VAC cycles Initial contact resistance : 10 mω max. at 1A V Insulation resistance : MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame 0 Vrms 50 Hz min. between terminals Electrical life : cycles at full load Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Mechanical life : cycles Packaging unit : 0 pieces (models Ø ) or 40 pieces (models Ø 19) MATERIALS Case : PT s : brass, silver plated (C) or silver (A) ushing : stainless steel Actuator : stainless steel CUT-OUTS Panel cut-out : Ø 19, mm (.755) or Ø, mm (.874) Min. pitch for matrix mounting : 30 mm (1.181) x 30 mm (1.181) Degree of protection according to EN 5010, June 95 (NFC 0-015) ROUSTNESS SEALING ( OPTION T ) Model Ø 19 mm (.748) Model Ø mm (.866) 1.7 Kg 9.5 cm Hammer radius 5 mm IK08 Striking energy: 5 joules (5Nm) 5 Kg 40 cm Hammer radius 50 mm IK10 Striking energy: 0 joules (0Nm) 1 Impacts on actuator according to CECC Hammer radius 10 mm 0.3 Kg 34 cm 10 strokes Striking energy: 1 joule (1Nm) 1.5 Kg 34 cm 10 strokes Striking energy: 5 joules (5Nm) ➀ internal gasket Front panel sealing (IP65) ➁ external gasket APEM
4 Anti-vandal pushbutton switches ushing Ø 19 (.748) - momentary (NO) Series ush./act. Case Function Terminal ush./act. Sealing AV 3 40 NO (function 3) D C A 9 N T To order a sealed product, replace N with T at the end of P/N. ASIC MODEL Short case - flat actuator - AV N Hex nut (.866) across flats ø19.00x1.00 SI (.748DIAx1.00 IS) 5.00 (.196) 7.30 (.87).80 (.110) AV091003C940N Solder lug / quick-connect term. AV091003C40N ø ø15.00 ø.80x0.5 (.110x.019) 1.0 (.047) for wires 1,5 mm max (.374) (.55) Long case - flat actuator - UL-CSA approved - AV N New! Hex nut (.866) across flats Ø19.00x1.00 SI (.748DIAx1.00 IS) 5.00 (.196) AV090003A940N Ø Ø for wires 1,5 mm max (.456) (.55) (.83) OTHER CONFIGURATIONS 3.60 (.141) Ø Flush model Case : replace with 1 for short case and 0 for long case. Ø Ø.0 Mini (.874DIA Min.) 1.0 (.047) 1.30 Mini (.051 Min.) Ø19.0 (.755DIA) AV19 003C940N Solder lug / quick-connect terminals AV19 003C40N AV9D 003C940N Solder lug / quick-connect terminals AV9D 003C40N APEM -91
5 Anti-vandal pushbutton switches ushing Ø (.866) - momentary (NO) Series ush./act. Case Function Terminal ush./act. Sealing AV 3 C 40 NO (function 3) 03 0 M3 M C A 9 N T To order a sealed product, replace N with T at the end of P/N. ASIC MODEL Short case - flat actuator - AV N Hex nut 5 (.984) across flats øx1.00 SI (.866DIAx1.00 IS) 7.30 (.87).80 (.110) AV031003C940N 1.0 (.047) Solder lug / quick-connect term. AV031003C40N ø5.00 (.984DIA) ø15.00 (.59DIA).80x0.5 (.110x.019) for wires 1,5 mm max (.500) 6.30 (.48) 5.00 (.196) Long case - flat actuator - UL-CSA approved - AV N New! Øx1.00 SI (.866DIAx1.00 IS) Hex nut 5 (.984) across flats AV030003A940N Ø5.00 (.984DIA) (.59DIA) for wires 1,5 mm max (.590) (.48) 5.00 (.196) OTHER CONFIGURATIONS 3.60 (.141) Ø5.00 (.984DIA) Flatted bushing Case : replace with 1 for short case and 0 for long case. Ø5.00 (.984DIA) AV0 003C940N Solder lug / quick-connect term. AV0 003C40N Flat actuator AVM3 003C940N AVM 003C940N Ø.0 (.874DIA) (.393 ) -9 APEM
6 Security pushbutton switches with large actuator ushing Ø (.866) - momentary (combined NC/NO) Combined NC/NO Series ushing diameter AV ush./act. Actuator ush./act. matl L 40 P C / terminals 4 See next page. SPECIFICATIONS Max. current/voltage rating with resistive load : 5A 50VAC Initial contact resistance : 100 mω max. Insulation resistance : MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame Electrical life : cycles at 1A 50VAC cycles at full load Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.36) max. Operating temperature : -0 C to +55 C Mechanical life : cycles Front panel sealing : IP65 Packaging unit : 0 pieces (except black chrome plated : 16 pieces) MATERIALS Case : polyester, glass filled s : silver/nickel alloy ushing : stainless steel (std) Actuator : stainless steel (std) CUT-OUT Panel cut-out : Ø, (.874) or Ø 4, (.95) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) All model numbers below are for switches with standard bushing/actuator. ASIC MODEL Flat actuator - solder lug terminals - AVLP O-ring 9.00 (1.14) Hex nut 5 (.984) across flats 1.50 (.49) AVLP40 Ø6.00 (1.03DIA) Ø0.00 (.787DIA) 4.00 (.157) 0.50 (.019) Øx1.00 SI (.866DIAx1.00 IS) 1.40 (.055).40 (.094) OTHER CONFIGURATIONS Recessed actuator AVL40 AVLC40 APEM -93
7 Security pushbutton switches with large actuator ushing Ø 4 (.944) - low profile - momentary (combined NC/NO) ASIC MODEL Flat actuator - solder lug terminals - AV4LP O-ring (1.13) Hex nut 7 (1.06) across flats 14.0 (.559) AV4LP40 Ø30.00 (1.181DIA) Ø0.00 (.787DIA) 1.30 (.051) 4.00 (.157) 0.50 (.019) Ø4.00x1.00 SI (.944DIAx1.00 IS) 1.40 (.055).40 (.094) OTHER CONFIGURATIONS Recessed actuator AV4L40 AV4LC40 USHING/ACTUATOR MATERIAL For non-standard, replace 40 with one of the following codes. Models with non-anodized actuator CODE USHING ACTUATOR 40 (standard) Stainless steel Stainless steel 0 Chrome plated brass Chrome plated brass Models with anodized actuator CODE USHING ACTUATOR COLOUR 1 lack chrome plated brass Chrome plated brass 4 Stainless steel Replace with one of the following codes : 1 : blue - : black - 3 : pale green - 3F : dark green - 4 : natural - 5 : gold yellow 6 : red - 6 : maroon CONTACT / TERMINALS (standard) NC/NO, solder lug terminals ø1.40 (.055 DIA) 4 NC/NO, quick-connect terminals 4.80 (.110) APEM
8 Mushroom head security pushbutton switches ushing Ø (.866) - momentary (combined NC/NO) Series ushing diameter ush./act. Actuator colour / terminals AV PNA see below 4 Combined NC/NO SPECIFICATIONS Max. current/voltage rating with resistive load : 5A 50VAC Initial contact resistance : 100 mω max. Insulation resistance : MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame Electrical life : cycles at 1A 50VAC cycles at full load Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.36) max. Operating temperature : -0 C to +55 C Mechanical life : cycles Front panel sealing : IP65 Packaging unit : 16 pieces MATERIALS Case : polyester, glass filled s : silver/nickel alloy ushing : brass, nickel plated Actuator : aluminium, anodized CUT-OUT Panel cut-out : Ø, (.874) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) ASIC MODEL Solder lug terminals - red actuator - AVPNA 5.00 (.984) Hex nut 5 (.984) across flats Joint (O-ring) 8.50 (.334) AVPNA6 ø30.00 (1.181DIA) (.45) 4.00 (.157) 0.50 (.019) øx1.00 SI (.866DIAx1.00 IS) 1.40 (.055).40 (.094) ACTUATOR ANODIZATION COLOUR 1 : blue - : black - 3 : pale green - 3F : dark green - 4 : natural - 5 : gold yellow - 6 : red - 6 : maroon CONTACT / TERMINALS (standard) NC/NO, solder lug terminals ø1.40 (.055 DIA) 4 NC/NO, quick-connect terminals 4.80 (.110) APEM -95
9 Security pushbutton switches ushing Ø 16 (.69) - momentary (NO) Series ush./act. Function Case matl. Term. ush./act. Sealing AV 3 0 C 9 00 NO (function 3) K See options page. SPECIFICATIONS Max. current/voltage rating with resistive load : 00mA 48 VDC - 100mA 48VDC Initial contact resistance : 50 mω max. Insulation resistance : MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame Electrical life : cycles at 00mA 48VDC cycles at 100mA 48VDC Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.36) max. Operating temperature : -30 C to +70 C Mechanical life : cycles Packaging unit : 60 pieces MATERIALS Case : PT s : brass, silver plated (C) ushing and actuator : nickel plated brass (std) CUT-OUT Panel cut-out : Ø 16, (.637) Min. pitch for matrix mounting : 4 mm x 4 mm (.944 x.944) All model numbers below are for switches with standard bushing/actuator, without marking. ASIC MODEL Flat actuator - screw terminals - AV06 Hex nut 19 (.748) across flats AV0630C900 ø18.00 (.708DIA) ø1 (.47DIA) ø16.00x1.00 SI (.69DIAX1.00 IS) 1.50 (.059) 9.50 (.374) w. chamfer 1.50 (.059) 11.0 (.440) for wires 1,5 mm max. OTHER CONFIGURATIONS 1.50 (.059) AV1630C900 AV0830C APEM
10 New! AV series Security pushbutton switches ushing Ø 16 (.69) - latching action Series ush./act. Function Case matl. Term. ush./act. Sealing AV 1 1 A 00 OFF ON K See options page. SPECIFICATIONS Max. current/voltage rating with resistive load :1,5A 50VAC - 1A 4VDC Initial contact resistance : 50mΩ max. Insulation resistance : 1 GΩ min. at 500VDC Dielectric strength : Vrms 50 Hz min. between terminals Vrms 50 Hz between terminals and frame Electrical life : cycles at 1,5A 50VAC cycles at 1A 4VDC Torque : 5 Nm min Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.36) max. Operating temperature : -30 C to +70 C Mechanical life : cycles Packaging unit : 5 pieces MATERIALS Case : PA-6T, UL94-V0 s : silver (A) Gold plated silver (AD) on request. ushing and actuator : nickel plated brass (std) CUT-OUT Panel cut-out : Ø 16, (.637) Min. pitch for matrix mounting : 4 mm x 4 mm (.944 x.944) All model numbers below are for switches with standard bushing/actuator, without marking. ASIC MODEL Solder lug terminals - AV..11A00 Hex nut 19 (.748) across flats 3.40 (.133).30 (.090) Flat actuator AV0611A00 OFF - ON AV1611A00 OFF - ON Ø18.00 (.708DIA) Ø1 (.47DIA) Ø18.00 (.708DIA) Ø1 (.47DIA) 1.40 (.055) Ø16.00X1.00 SI (.69DIAX1.00 IS) 1.50 (.059) 9.00 (.354) 15.0 (.598) OTHER CONFIGURATIONS Straight PC terminals Quick-connect terminals 3.50 (.137) 0.50 (.019) 8.00 (.314) 5.08 (.00) 1.10 (.043) 0.50 (.019) 1.0 (.047).40 (.094).80 (.047) Flat actuator AV0611A400 AV1611A400 Flat actuator AV0611A800 AV1611A800 APEM -97
11 Security pushbutton switches New! ushing Ø 19 (.748) - momentary (combined NC/NO) Combined NC/NO Series ushing diameter AV 19 ush./act. Actuator ush./act. matl / terminals L 00 7 P See below SPECIFICATIONS Max. current/voltage rating with resistive load : 5A 50VAC - 5A 15VAC cycles 5A 15VDC - 3A 30VDC cycles Initial contact resistance : 100 mω max. Insulation resistance : MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between term. and frame Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 9 mm (.354) max. Operating temperature : -0 C to +85 C Mechanical life : cycles Front panel sealing : IP65 Packaging unit : 0 pieces MATERIALS Case : PA 6/6 s : silver ushing : nickel pl. brass (std) Actuator : nickel pl. brass (std) CUT-OUT Panel cut-out : Ø 19, mm (.755) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) All model numbers below are for switches with standard bushing/actuator. ASIC MODEL Solder lug terminals - AV O-ring Hex nut (.866) across flats 3.60 (.141) Ø19.00X1.00 SI (.748DIAX1.00 IS) 1.50 (.059) Flat actuator AV19LP (.019) Ø (.590) 1 3 AV19L007 Ø (.590) (.515) 1.60 (.496) 3.60 (.141) USHING/ACTUATOR MATERIAL For non-standard, replace 00 with one of the following codes. CODE USHING ACTUATOR 00 (std) Nickel plated brass Nickel plated brass 0 Chrome plated brass Chrome plated brass 40 Stainless steel Stainless steel APEM
12 Security pushbutton switches ushing Ø 19 (.748) - momentary (NO) Series ush./act. Case Function matl. Term. ush./act. Marking Sealing AV 3 C 00 NO (function 3) P C A 9 See options page. K SPECIFICATIONS Max. current/voltage rating with resistive load (C contacts): A 48 VDC Approved ratings of models with long case and A contacts (AV..000) : UL-CSA : 4A 50VAC - 8A 15VAC cycles Initial contact resistance : 10 mω max. at 1A V Insulation resistance : MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame 0 Vrms 50 Hz min. between terminals Electrical life : cycles at full load Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Mechanical life : cycles Packaging unit : 40 pieces MATERIALS Case : PT s : brass, silver plated (C) or silver (A) ushing : brass, nickel plated (std) Actuator : brass, nickel plated (std) CUT-OUT Panel cut-out : Ø 19, mm (.755) Min. pitch for matrix mounting : 30 mm (1.181) x 30 mm (1.181) All model numbers below are for switches with standard bushing/actuator, without marking. ASIC MODEL Short case - flat actuator - AV Hex nut (.866) across flats ø19.00x1.00 SI (.748DIAx1.00 IS) 7.30 (.87).80 (.110) AV091003C900 Solder lug / quick-connect term. AV091003C00 for wires 1,5 mm max. ø ø (.531) 5.50 (.16) 5.00 (.196).80x0.5 (.110x.019) 1.0 (.047) Long case - flat actuator - UL-CSA approved - AV Hex nut (.866) across flats New! Ø19.00x1.00 SI (.748DIAx1.00 IS) 5.00 (.196) AV090003A900 Ø for wires 1,5 mm max (.58) (.413) APEM -99
13 Security pushbutton switches ushing Ø 19 (.748) - momentary (NO) OTHER CONFIGURATIONS 3.60 (.141) Ø With knurled nut for matrix mounting 5 (.984) x 5 (.984) Ø Case : replace with 1 for short case and 0 for long case (.177) Ø 4.50 (.177) 5.00 (.984) (.984) (.984) AV19 003C900 Solder lug / quick-connect terminals AV19 003C00 Flat actuator, screw term. AV9P 003C900 Flat actuator, solder lug term. AV9P 003C00, screw term. AV9 003C900 Curved act., solder lug term. AV9 003C00 Wrench available under P/N U199. AV series Security pushbutton switches ushing Ø 19 (.748) - other electrical functions ushing Ø 19 (748) - combined NC/NO - AV Single pole, solder lug terminals Gold plated silver contacts Current/voltage rating with resistive load : max. : 1A 30V - min : 10µA 5V Note : a current above 100mA damages the gold plating. Dielectric strength : Vrms between terminals 0 Vrms between terminals and frame Electrical life : cycles at full load Mechanical life : cycles Packaging unit : 0 pieces Further specifications : see previous page. Flat actuator AV099035D00 AV199035D00 ushing/actuator s, marking and sealing : see options page. Ø 3.60 (.141) Ø19.00x1.00 SI (.748DIAx1.00 IS) (.590) Hex nut (.866) across flats 7.50 (.95) 1.0 (.047) 0.80 (.031) 5.0 (.04) x0.40 (.078x.015) 5.08 (.00) APEM
14 Security pushbutton switches ushing Ø (.866) - momentary (NO) Series ush./act. Case Function matl. Term. ush./act. Marking Sealing AV 3 C 00 NO (function 3) 03 0 M3 M C A 9 See options page. K SPECIFICATIONS Max. current/voltage rating with resistive load (C contacts): A 48 VDC Approved ratings of models with long case and A contacts (AV..000) : UL-CSA : 4A 50VAC - 8A 15VAC cycles Initial contact resistance : 10 mω max. at 1A V Insulation resistance : MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame 0 Vrms 50 Hz min. between terminals Electrical life : cycles at full load Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Mechanical life : cycles Packaging unit : 0 pieces MATERIALS Case : PT s : brass, silver plated (C) or silver (A) ushing : brass, nickel plated (std) Actuator : brass, nickel plated (std) CUT-OUTS Panel cut-out : Ø, mm (.874) Min. pitch for matrix mounting : 30 mm (1.181) x 30 mm (1.181) All model numbers below are for switches with standard bushing/actuator, without marking. ASIC MODEL Short case - flat actuator - AV Hex nut 5 (.984) across flats øx1.00 SI (.866DIAx1.00 IS) 7.30 (.87).80 (.110) AV031003C (.047) Solder lug / quick-connect term. AV031003C00 ø5.00 (.984DIA) ø15.00 (.59DIA).80x0.5 (.110x.019) for wires 1,5 mm max (.500) 6.30 (.48) 5.00 (.196) Long case - flat actuator - UL-CSA approved - AV New! Øx1.00 SI (.866DIAx1.00 IS) Hex nut 5 (.984) across flats AV030003A900 Ø5.00 (.984DIA) (.59DIA) for wires 1,5 mm max (.590) (.48) 5.00 (.196) APEM
15 Security pushbutton switches ushing Ø (.866) - momentary (NO) OTHER CONFIGURATIONS 3.60 (.141) Ø5.00 (.984DIA) Flatted bushing Case : replace with 1 for short case and 0 for long case. Ø5.00 (.984DIA) AV0 003C900 Solder lug / quick-connect terminals AV0 003C00 Flat actuator AVM3 003C900 AVM 003C900 Ø.0 (.874DIA) (.393 ) AV series Security pushbutton switches ushing Ø (.866) - other electrical functions ushing Ø (.866) - Normally closed (NC) - AV..100 Single pole, screw terminals, without marking Silver plated copper contacts (C) Max. current/voltage rating with resistive load : A 50VAC - 3A 15VAC -,5A 4VDC Dielectric strength : 0 Vrms 50 Hz min. betw. term. and frame 0 Vrms. 50 Hz min. between terminals Electrical life : cycles at 0,3A 4VAC or DC cycles at full load Packaging unit : 0 pieces Flat actuator AV0310C00 AV010C00 (.59DIA) Ø5.00 (.984DIA) (.59DIA) 3.60 (.141) Hex nut 5 (.984) across flats Øx1.00 SI (.866DIAx1.00 IS) (.551) (.606) Øx0.50 (.118DIAx.0.50) 7.00 (.75) 13.0 (.519) ushing Ø (.866) - alternate action - AV Double pole, solder lug/quick-connect term., curved actuator Silver contacts Max. current/voltage rating with resistive load : 3(1,5)A 50VAC - 6A 15VAC - 3A 4VAC or DC Dielectric strength : 0 Vrms min. between terminals and frame Electrical life : cycles at full load cycles at 1A 4VAC or DC Mechanical life : cycles Packaging unit : 10 pieces Ø5.00 (.984DIA) (.59DIA) Øx1.00 SI (.866DIAx1.00 IS) 1.60 (.063) Hex nut 5 (.984) across flats 0.50x.80 (.019x.110) 5.80 (.8) 8.40 (.330) AV044746A00 ON - ON 3.60 (.141) (.551) (.811) (.83) Further specifications : see previous page. ushing/actuator s, marking and sealing : see options on next page APEM
16 Security pushbutton switches Options After selecting basic model number, fill in last 3 boxes with desired options. Series AV ush./act. Case Function matl. Term. ush./act. Marking Sealing USHING/ACTUATOR MATERIAL Flat or curved metal actuator For non-standard, replace 00 with one of the following codes. ** Option 80 not available on models with dia. 16 mm (.69) bushing CODE USHING ACTUATOR 00 (standard) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 1 Nickel plated brass Chrome plated brass 0 Chrome plated brass Chrome plated brass 30 Chrome plated brass Stainless steel 40 Stainless steel Stainless steel 80 ** Varnished polished brass Varnished polished brass Flat thermoplastic actuator (not available with dia. 16 mm (.69) bushing) CODE USHING ACTUATOR COLOUR 0 (standard) Nickel plated brass Chrome plated brass 8 Varnished polished brass Replace with one of the following codes. 1 : blue - : black - 3 : green - 4 : grey 5 : yellow - 6 : red - 7/1: white - 9 : orange MARKING For flat or curved actuator. Not available on model AV0310C00. - by engraving on brass actuator (stainless steel on request) - by hot stamping on thermoplastic actuator (0.314) 1.50 (0.059) (0.590DIA) CODE TYPE OF MARKING TYPE 0 to 9 Numbers 0 to 9 X Symbol * Y Symbol # A to N Letters A to N P to W Letters P to W 0 Letter O Letter O : same code and same design as number 0. For special symbols, consult factory. Minimum order : 500 pieces Select an option from each of the two tables below. CODE COLOUR OF MARKING COLOUR rass actuator 0 (standard) Same as finish lack Note : a finished product supplied in version 0 cannot be modified to version "". Thermoplastic actuator lack 7 White SEALING lank No sealing 1 1 K Frontal panel sealing (IP65) For s with bushing Ø 16 ➀ elastomeric membrane ➁ external gasket ➀ internal gasket ➁ external gasket K Front panel sealing (IP65) For s with bushing Ø 19 or Ø APEM
17 Snap-action security pushbutton switches ushing Ø 19 (.748) - illuminated or not - momentary (NO) NO (function 3) Series ush./act. Case Illum. or not Funct. matl. Term. ush./act. LED colour AV C7 3 D L 0 9 Marking Seal. K See options on next page. SPECIFICATIONS Max. current/voltage rating with resistive load : 50mA 4VDC LED voltage and consumption : -colour LED : V (3V max.) 0mA Other colours : V (3V max.) 10mA A resistor must be series-connected by the user.** Initial contact resistance : 100 mω max. Insulation resistance : MΩ min. at 500VDC Dielectric strength : 500 Vrms 50 Hz min. between terminals 0 Vrms 50 Hz min. between terminals and bushing Electrical life : cycles at full load Operating force : 7 N +/-N Travel : 0,7 mm (.07) +/- 0,1 mm (.003) Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Soldering : 70 C max. during 3 sec. Packaging unit : 40 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current MATERIALS Case : PT UL94-V0 Terminals : brass, gold plated s : gold plated dome ushing : brass, nickel plated (std) Actuator : brass, nickel plated (std) LED CUT-OUTS Panel cut-out : Ø 19, mm (.755) Min. pitch for matrix mounting : 30 mm (1.181) x 30 mm (1.181) All model numbers below are for switches with standard bushing/actuator, without marking. Flat actuator - non-illuminated Hex nut (.866) across flats Ø19.00x1.00 SI (.748DIAx1.00 IS) 1.90 (.074) Solder lug terminals AV09C703D (.043) AV09C703D900 Ø Ø 4.15 (.163) Also available with curved actuator : AV19C703D00 or AV19C703D (.531) 13.0 (.519) (.531) 3.90 (.153) Flat actuator - illuminated Hex nut (.866) across flats Ø19.00x1.00 SI (.748DIAx1.00 IS) 1.90 (.074) Solder lug terminals AV09C7L3D (.043) AV09C7L3D Ø Ø Ø10.00 (.393DIA) 4.15 (.163) (.531) 13.0 (.519) (.531) 3.90 (.153) APEM
18 Snap-action security pushbutton switches Options After selecting basic model no., fill in last 4 boxes with desired options. Series ush./act. AV Case Illum. or not Funct. matl. Term. ush./act. LED colour Marking Seal. USHING/ACTUATOR MATERIAL Non-illuminated models CODE USHING ACTUATOR For non-standard, replace 00 with one of the following codes. Illuminated models CODE USHING ACTUATOR 00 (std) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 30 Chrome plated brass Stainless steel 40 Stainless steel Stainless steel 80 Varnished polished brass Varnished polished brass 00 (std) Nickel plated brass Nickel plated brass 0 Chrome plated brass Chrome plated brass 40 Stainless steel Stainless steel 45 Stainless steel Nickel plated brass 80 Varnished polished brass Varnished polished brass LED COLOUR lank No LED 1: lue - 3 : Green - 5 : Yellow - 6 : Red - 7 : White - 9 : Amber - : Red/green For flat or curved actuator. - by engraving on non-illuminated brass actuator (stainless steel on request). - by hot stamping on thermoplastic insert ( illuminated actuators) 8.00 (0.314) MARKING 1.50 (0.059) Ø10.00 (0.393DIA) 1.00 (0.039) CODE TYPE OF MARKING TYPE 0 to 9 Numbers 0 to 9 X Symbol * Y Symbol # A to N Letters A to N P to W Letters P to W 0 Letter O Letter O : same code and same design as number 0. For special symbols, consult factory. Minimum order : 500 pieces Select an option from each of the two tables below. CODE COLOUR OF MARKING COLOUR Non-illuminated actuators 0 (standard) Same as finish lack Note : a finished product supplied in version 0 cannot be modified to version "". Illuminated actuators lack (on white) SEALING lank No sealing 1 K Front panel sealing (IP65) ➀ internal gasket ➁ external gasket APEM
19 Snap-action security pushbuttons with overmolded actuator ushing Ø 19 (.748) - illuminated or not - momentary (NO) New! Series ush./act. Illum. or not matl. Term. ush. Overmolding LED colour Actuator Seal. AV 9 D 0 NO (function 3) S0 SL 4 See options on next page. K SPECIFICATIONS Max. current/voltage rating with resistive load : 50mA 4VDC LED voltage and consumption : -colour LED : V (3V max.) 0mA Other colours : V (3V max.) 10mA A resistor must be series-connected by the user.** Initial contact resistance : 100 mω max. Insulation resistance : MΩ min. at 500VDC Dielectric strength : 500 Vrms 50 Hz min. between terminals 0 Vrms 50 Hz min. between terminals and bushing Electrical life : cycles at full load Operating force : 7 N +/-N Travel : 0,7 mm (.07) +/- 0,1 mm (.003) Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Soldering : 70 C max. during 3 sec. Packaging unit : 40 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current Solder lug terminals MATERIALS Case : PT UL94-V0 Terminals : brass, gold plated s : gold plated dome ushing : brass, nickel plated (std) Actuator : stainless steel, with thermoplastic overmolding LED CUT-OUTS Panel cut-out : Ø 19, mm (.755) Min. pitch for matrix mounting : 30 mm (1.181) x 30 mm (1.181) Hex nut (.866) across flats 1.90 (.074) Illuminated AV9SLD 1.10 (.043) Non illuminated AV9S0D Ø Ø Ø10.00 (.393DIA) 4.15 (.163) 9.80 (.385) 4.30 (.169) Also available with bushing Ø (.866) : on request. Straight PC terminals Hex nut (.866) across flats 4.00 (.157) Illuminated AV9SLD4 Non illuminated AV9S0D4 Ø Ø Ø10.00 (.393DIA) 6.00 (.36) 9.80 (.385) 4.30 (.169) Also available with bushing Ø (.866) : on request APEM
20 New! AV series Snap-action security pushbuttons with overmolded actuator Options After selecting basic model no., fill in last 5 boxes with desired options. Series ush./act. AV Illum. or not matl. Term. ush. Overmolding LED colour Actuator Seal. USHING MATERIALS COLOUR OF OVERMOLDING LED COLOURS CODE MATERIAL CODE COLOUR CODE COLOUR 0 (std) Nickel plated brass Chrome plated brass 4 Stainless steel 5 Gold plated brass 6 Chrome plated brass, satin 7 Chrome pl. brass, matt black 8 Varnished polished brass 9 Polished brass 1 lue lack 3 Green 4 Grey 5 Yellow 6 Red 7 White 8 Translucent 9 Orange lank No LED 1 lue Red/green 3 Green 5 Yellow 6 Red 7 White 9 Amber ACTUATOR STYLES The ring and symbols are obtained by photochemical engraving of a stainless steel insert. The insert is then overmolded in the desired colour. The following actuator s are available. For other s, consult factory. CODE DESCRIPTION Illuminated ring and disc Illuminated ring Arrow Loudspeaker OFF Double arrow RING/SYMOL SEALING lank No sealing 1 K Front panel sealing (IP65) ➀ internal gasket ➁ external gasket APEM
AV SERIES PUSHBUTTON SWITCHES Distinctive features
PUSHBUTTON SWITCHES Distinctive features Attractive, robust and durable Irremovable Anti-jamming construction : reduced travel to prevent insertion of foreign parts and mechanism protected against crushing
More information1200 series. Momentary pushbutton switches - round plunger. Distinctive features and specifications. Butt action contacts, double break
Distinctive features and specifications Butt action contacts, double break NF (EN 61058-1), UL and CSA approved ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - silver contacts
More informationMomentary pushbutton switches - round plunger
1200 series Momentary pushbutton switches - round plunger Distinctive features and specifications Butt action contacts, double break NF (EN 61058-1), UL and CSA approved ELECTRICAL SPECIFICATIONS Max.
More informationSealed pushbutton switches - bushing Ø 16 mm - momentary
Sealed pushbutton switches - bushing Ø 16 mm - momentary Distinctive features The IR series is a range of sealed momentary pushbutton switches with dia. 16 mm bushing. This series is divided into 2 families
More information8000 series Momentary or alternate action pushbutton switches
Distinctive features and specifications ushing Ø 6,35 (1/4) and Ø 11,9 (15/32) UL approved ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - silver contacts : 3A 250VAC - 6A
More informationIR series Sealed pushbutton switches - bushing Ø 16 mm - momentary
Sealed pushbutton switches - bushing Ø 16 mm - momentary Distinctive features The IR series is a range of sealed momentary pushbutton switches with dia. 16 mm bushing. This series is divided into 2 families
More informationIL series Sealed pushbutton switches for thick panels - long bushing Ø 12 mm - momentary
Distinctive features and specifications Momentary pushbuttons for thick panels Illuminated or non-illuminated Tactile feedback Flat round actuator for optional marking Sealed to IP67 ENVIRONMENTAL SPECIFICATIONS
More information18000 series Snap-action momentary pushbutton switches
Distinctive features and specifications Panel and PC mount models Snap-in panel mounting version Tactile feedback ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : Models for
More informationIP series Latching action pushbutton switches for harsh environments
Latching action pushbutton switches for harsh environments Distinctive features and specifications Latching action Actuator remains in the low position when ON. Illuminated and non-illuminated Compact
More informationSelection guide - Section B1 «I» range
Selection guide - Section «I» range New! New! New! New! New! New! Series IC IL IM IP IB-IS IHS IHL IQ mom. & latching hall effect hall effect momentary Page -2-6 -11-15 -25-29 -32-35 Poles 1 1 1 1 1 1
More information13000 series Professional quick-break momentary pushbutton switches
Distinctive features and specifications PC and panel mount models ushing Ø 6,35 (1/4) and 11,9 (15/32) UL and CECC approved ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : -
More informationMomentary or alternate action pushbutton switches. UL approved 3A 250VAC, 6A 125VAC. Availability : consult factory for details of approved models.
Distinctive features and specifications Bushing Ø 6,35 (1/4) and Ø 11,9 (15/32) UL approved ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - silver contacts : 4A 30VDC - gold
More informationPushbutton and key switches
Pushbutton and key switches Section ZP Tiny, metal bushing, momentary 3 SMT TP Tiny, SMT, washable, momentary 5 TP Tiny, washable, momentary 7 9100-9200-9500 Subminiature, momentary 13 IF Miniature, sealed,
More informationIQ series Sealed pushbutton switches - bushing Ø 16 mm - snap-in mounting
Sealed pushbutton switches - bushing Ø 16 mm - snap-in mounting Distinctive features Like the IR series, the IQ series is a range of sealed pushbutton switches with dia. 16 mm bushing. But IQ pushbuttons
More informationELECTRICAL SPECIFICATIONS
Distinctive features and specifications Panel and PC mount models Snap-in panel mounting version Tactile feedback ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : Models for
More informationTwo case lengths. Three electrical functions. Sealing options. Model X1146 with Ø 16 (.630) bushing ELECTRICAL SPECIFICATIONS.
Distinctive features and specifications Two case lengths Three electrical functions Sealing options Model X1146 with Ø 16 (.630) bushing Max. current/voltage rating with resistive load : - silver contact
More informationCommon features. Installation options. Aesthetic options
New! LPI series Distinctive features and applications UG1006-A Common features Large ergonomic actuator (Ø 35 mm) Tactile feedback Low behind-panel depth (21 mm max.) Stylish design Long life This series
More informationIR series. Sealed pushbutton switches bushing Ø 16 mm momentary standard version DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS
SW-IRMOM-1801 DISTINCTIVE FEATURES Screw version up to A Tactile feedback Sealed to IP6 Illuminated or non-illuminated Flat round actuator for optional marking ENVIRONMENTAL SPECIFICATIONS Front panel
More informationIP series. Pushbutton switches for harsh environments bushing Ø 12 mm momentary DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS
SW-IPMOM-1709 DISTINCTIVE FEATURES Illuminated or non-illuminated Tactile feedback Wide variety of configurations Flat round actuator for optional marking Sealed to IP67 and IP69K ENVIRONMENTAL SPECIFICATIONS
More information9000 SERIES SUBMINIATURE MOMENTARY PUSHBUTTON SWITCHES Overview
A 9000 SERIES Overview 9 SERIES Number of poles 3 Single pole Electrical functions 2 Normally closed (NC) 3 Normally open (NO) Terminals, case and bushing Case height 8 (.314) 2 Straight terminals - threaded
More information8000 series. Momentary or alternate action pushbutton switches DISTINCTIVE FEATURES ELECTRICAL SPECIFICATIONS GENERAL SPECIFICATIONS MATERIALS
SW-8000-808 DISTINCTIVE FEATURES Momentary or alternate Bushing Ø 6.35 (/4) and Ø.9 (5/3) UL approved ELECTRICAL SPECIFICATIS Max. current/voltage rating with resistive load : - silver contacts : 4 A 30
More informationIP series. Pushbutton switches for harsh environments bushing Ø 12 mm latching DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS
SW-IPLATCH-802 DISTINCTIVE FEATURES Latching action Illuminated or non-illuminated Compact Flat round actuator for optional marking Sealed to IP67 ENVIRONMENTAL SPECIFICATIONS Front panel sealing : IP67
More informationSeries AV. Pushbutton Switches NUT O-RING HOW TO ORDER
Pushbutton Switches SPECIFICATIS: BUSHING: 22mm. CTACT RATING: 2A @ 48VDC or 125VAC. ELECTRICAL LIFE: 10,000cycles at full load. CTACT RESISTANCE: 10m-ohms max. initial @2-4VDC. INSULATI RESISTANCE: 1,000M-ohms
More informationSealed to IP67 Dia. 12 mm or 16 mm bushing Momentary or latching Illuminated or non-illuminated Custom options Comprehensive range
I range Sealed pushbutton switches Sealed to IP67 Dia. 12 mm or 16 mm bushing Momentary or latching Illuminated or non-illuminated Custom options Comprehensive range I range Sealed pushbutton switches
More informationAPEM LPI series Front or rear mounting Illuminated or non-illuminated Flexibility of marking Meeting the requirements of EN81-70 Ø 35 mm actuator
APEM LPI series Front or rear mounting Illuminated or non-illuminated Flexibility of marking Meeting the requirements of EN81-70 Ø 35 mm actuator Distinctive features and applications Common features Large
More informationAPEM. LPI series. Tactile pushbutton switches with large actuator. Ø 35 mm actuator
APEM LPI series Front or rear mounting Illuminated or non-illuminated Flexibility of marking Meeting the requirements of EN81-70 Ø 35 mm actuator Distinctive features and applications Common features
More information2600 SERIES ILLUMINATED AND NON-ILLUMINATED ROCKER SWITCHES Overview
Overview 6 SERIES Electrical functions Frame type 1 ON - OFF 4 ON ON ON MOM - ON 6 ON - ON 7 MOM OFF MOM 8 ON OFF MOM 9 ON OFF ON double pole only LH LP Plain With protection guard Number of poles Special
More informationFP series Fully illuminated pushbutton switches - bushing Ø 30 mm - momentary or latching
Fully illuminated pushbutton switches bushing Ø 30 mm momentary or latching Distinctive features and specifications Full actuator or symbol illumination UG1410AR3 Snapin and threaded bushing models Large
More informationCIT SWITCHTM ANT SPECIFICATIONS
Wide variety of applications from consumer electronics to commercial Standard epoxy sealed terminations Gold contacts available for low power applications Available support brackets for greater stability
More informationFP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching
Fully illuminated pushbutton switches bushing Ø 24 mm momentary or latching Distinctive features and specifications Threaded bushing UG1410AR2 Full actuator or symbol illumination Large but lightweight
More informationSecurity Switches. Anti Vandal, Pushbutton. Specifications. Specifications S76 S77. Features.748 (19mm) bushing diameter
Anti Vandal, Pushbutton S76.287 (7.3) c: Screw (Assembled).098 (2.5) Typ.142 (3.6) Type Circuitry Action Actuator g 54 377 SPST NO OFF (ON) Stainless Steel, Flat S76b 54 378 SPST NO OFF (ON) Stainless
More information5000 SERIES TOGGLE SWITCHES Distinctive features B
5000 SERES TOGGLE SWTCHES Distinctive features THE WDEST RANGE N MNATURE SWTCHES 7 7 actuators including toggles, paddle levers and locking levers in different lengths. 5 5 contact materials from dry circuit
More informationVarious rocker colours. Illuminated or non-illuminated ELECTRICAL SPECIFICATIONS
00 series istinctive features and specifications Three rocker shapes : plain, Vshaped or concave Various rocker colours Frame with protection guard on 00LP models Illuminated or nonilluminated UL, CSA,
More information600H AND 600NH SERIES TOGGLE SWITCHES - HIGH AMPERAGE Overview
600H AND 600NH SERES TOGGLE SWTCHES - HGH AMPERAGE Overview 6 SERES Number of poles Electrical functions Actuator and terminals Single pole Double pole 5 For pole, see 600 series. ON - OFF 5 MOM - ON 6
More informationFully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching
istinctive features and specifications Full actuator or symbol illumination UG1410R1 Suited for integrated designs Large but lightweight Sealed to IP69K Pad printed or laser etched symbols Pad printing
More informationAttractive rugged rocker switch
istinctive features Attractive rugged rocker switch UG0AR Removable actuator Easy to stock Easy to customize Uptodate rocker design Smooth curves Wide choice of colours and symbols Laser etched symbols
More informationA1-A01-A02-A03 series
A1-A01-A02-A03 series Industrial controls Distinctive features The A01 and A02 series offer ranges of : - pushbutton switches, illuminated or not - indicators - 2 or 3 position keylock switches - 2 or
More informationPushbutton switches & indicators. Panel Sealed to IP65. Push on tab terminals 6A 250VAC AGENCY APPROVALS
Distinctive features and specifications Panel Sealed to IP65 Single pole to four pole changeover Custom engraving or film legends options Push on tab terminals 6A 250VAC A01_AX1607USR1 ELECTRICAL SPECIFICATIONS
More informationAPEM. K range. Power rocker switches and indicators. Unique rocker design
APEM K range Power rocker switches and indicators Wide range Laser etched symbols Illuminated or nonilluminated Optionally sealed to IP8 Unique rocker design K range Power rocker switches and indicators
More informationIHS series Hall effect pushbutton switches - bushing Ø 12 mm - momentary
IHS series Hall effect pushbutton switches - bushing Ø 12 mm - momentary Distinctive features and specifications UG1410A Momentary pushbutton (NO) 5 million cycles Low behind-panel depth Standard and high
More information600H and 600NH series Toggle switches - high amperage
600H and 600NH series Toggle switches - high amperage Distinctive features and specifications UG1410 Construction Terminal and contact support are manufactured from a single piece of metal. The contacts
More informationANT. Materials. Features. Miniature Toggle
Specificationscations RoHS Compliant ANT Electrical Ratings Electrical Life Contact Resistance 5A @ 0VAC, 8VDC A @ 50VAC See Contact Options 50,000 cycles typical
More informationS and SF series Washable miniature toggle switches
S and SF series Washable miniature toggle switches Distinctive features and specifications Sealed Secure assembly of the two case parts Internally sealed bushing Epoxy sealed terminals Process compatible
More informationA1-A01-A02-A03 series Industrial controls
A-A0-A0-A0 series Industrial controls Distinctive features The A0 and A0 series offer ranges of : - pushbutton switches, illuminated or not - indicators - or position keylock switches - or position rotary
More informationSealed toggle switches
Distinctive features and specifications Completely sealed switching chamber Three types of terminals UL approved ELECTRICL SPECIFICTIONS Max. current/voltage rating with load and electrical life at full
More informationANR SPECIFICATIONS. MATERIALS RoHS COMPLIANT - E222871
Wide variety of applications from consumer electronics to commercial Standard epoxy sealed terminations Gold contacts available for low power applications Available support brackets for greater stability
More informationSeries. Robust and attractive.
Series 82 Robust and attractive. www.eao.com Series 82 Robust and attractive. With Series 82, EAO offers the optimal pushbutton for vandal-resistant, stylish HMI controls used in harsh industrial environments,
More informationPLK & PLR SERIES Professional keylock or rotary switches
ISO OO AFAQ N /77c PLK & PLR SERIES Professional keylock or rotary switches NEW RANGE Miniature & subminiature to positions to poles PLK - PLR SERIES PROFESSIONAL KEYLOCK OR ROTARY SWITCHES Distinctive
More information600H - 600NH UL CSA NF-VDE UL 1054 CSA 22-2 EN
SW-600H-600NH-80 PNEL SWTCHES DSTNCTVE FETURES Robust mechanism High current/voltage rating nsulated or metal lever UL, CS and NF-VDE (EN 6058-) approved ELECTRCL SPECFCTS Max. current/voltage ratings
More informationSwitches. SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY 115VAC, 28VDC)
SWITCH SELECTION GUIDE Toggle Switches SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY (Resistive @ 115VAC, 28VDC) T1 2 or 3 Position, Momentary, 8A MIL-PRF-83731 15/32" or 1/4" dia.
More informationPower rocker switches
Distinctive features and specifications Protected rocker Illuminated or nonilluminated VDE (EN 08) approved Sealed to IP ELETRIL SPEIFITIONS urrrent/voltage rating : functions (ONOFF) and (ONON) : VD,
More information3500 SERIES HIGH PERFORMANCE TOGGLE SWITCHES - ENVIRONMENTALLY SEALED Distinctive features
HGH PERFORMNCE TOGGLE SWTCHES - ENVRONMENTLLY SELED Distinctive features Completely sealed switches withstanding 0,1 bar pressure Front face and cover-to-case silicone seal Moulded-in terminal inserts
More informationPushbutton switches & indicators. Panel Sealed to IP65. Push on tab terminals 6A 250VAC AGENCY APPROVALS
Distinctive features and specifications A01_AX1607US Panel Sealed to IP65 Single pole to four pole changeover Custom engraving or film legends options Push on tab terminals 6A 250VAC PANEL CUT OUT ELECTRICAL
More informationSWITCHES. Other switch types include conventional, push-button and toggle switches.
Switches Manufactured from Stainless Steel, Bulgin s extensive range of vandal resistant security switches are designed with a high resistance to wear and tear, corrosion and harsh use in potentially hostile
More informationPower rocker switches with protection guard
Distinctive features and specifications Protected against accidental actuation SWKH709 Wide choice of colors Laser etched or pad printed symbols Illuminated or nonilluminated Sealed to IP9K ELECTRICAL
More informationIndustrial controls. Section G
Industrial controls Section A1 A01 A02 A03 Distinctive features and specifications 3 Engraved aluminium flush mounting pushbuttons & indicators - Panel cut-out Ø 22 (.866) 5 Pushbutton, rotary lever, keylock
More informationMiniature Stainless Steel Vandal Resistant
Miniature Vandal Resistant Prominent Button / Flush Profile Prominent and Flush Profile 2A, 36 dc (Front of Panel Only) Specification /3 /1 Operating Temp Range: 0.6Nm 0.6Nm PA Copper, Gold Plated PA Copper,
More informationSERIES 100 SWITCHES TOGGLE SWITCHES - MINIATURE. Phone: Fax: SPECIFICATIONS MATERIALS
TACT SERIES 100 - MINIATURE SPECIFICATIONS Contact Rating: Life Expectancy: Contact Resistance: Insulation Resistance: Dielectric Strength: See contact material options 40,000 make-and-break cycles at
More informationCapacitive Switches
Capacitive Switches www.capacitive-switch.com About Capacitive Switches The new CP series technology senses the touch of a finger and creates an electrical charge to activate the switches An auto-calibration
More informationCapacitive Switches
Capacitive Switches www.capacitive-switch.com langir About Capacitive Switches The new CP series technology senses the touch of a finger and creates an electrical charge to activate the switches An auto-calibration
More informationDistinctive Characteristics
Distinctive Characteristics Full face or spot illumination with incandescent lamps or multi-element LEDs, with or without resistors. Short Body Pushbuttons Series YB Choice of super bright LEDs in white,
More information8500 Series Subminiature Pushbutton Switches
Subminiature Switches Features/Benefits Pre-travel or over-travel models available Ratings up to 3 AMPS Reliable contact design RoHS compliant Typical Applications Detection Telecommunications and networking
More informationA1-A01-A02-A03 series Industrial controls
A-A0-A0-A0 series Industrial controls Distinctive features The A0 and A0 series offer ranges of : - pushbutton switches, illuminated or not - indicators - or position keylock switches - or position rotary
More informationIHS series Hall effect pushbutton switches - bushing Ø 12 mm - momentary Overview IHS SERIES Actuator shapes Electrical function Operating force Termi
IHS series Hall effect pushbutton switches - bushing Ø 12 mm - momentary Distinctive features and specifications Momentary pushbutton (NO) 5 million cycles Low behind-panel depth Standard and high actuator
More informationE Series Sealed Miniature Toggle Switches
Sealed Miniature Switches eatures/benefits Sealed against solder and cleaning process contaminants UL 94V-0 Nylon case and bushing Multi-positions ESD protection available RoHS compliant models available
More informationELECTRO-MECHANICAL MINIATURE SEALED. Long life Solder or PC terminals PanelsealedtoIP67
PUSHBUTTON SWITCHES ELECTRO-MECHANICAL MINIATURE SEALED SERIES 48EM: ACTUAL SIZE FLEX-TECH MINIATURE SEALED PUSHBUTTON SWITCHES This rugged multi-option sealed pushbutton series offers the utmost in choices
More informationProduct Range. Rocker & Paddle Switches. Rocker & Paddle Switches. Rocker & Paddle Switches
Product Range for Panel Mounting: F, TRD and Gemini Series for PCB Mounting: Gemini Series Main features: Sealed or unsealed versions Various switch functions Gold or silver contacts LED illumination available
More informationC&K E Series Sealed Miniature Toggle Switches
Sealed Miniature Switches eatures/benefits Sealed against solder and cleaning process contaminants UL 94V-0 Nylon case and bushing Multi-positions ESD protection available Typical Applications Telecommunications
More informationSwitches. Introduction
Introduction Switches Manufactured from, Bulgin s extensive range of vandal resistant security switches are designed with a high resistance to wear and tear, corrosion and harsh use in potentially hostile
More information7000 Series Miniature Toggle Switches
Miniature Switches eatures/benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy terminal-seal compatible with bottom wash cleaning RoHS complaint models available
More informationKSB & KSF Series Low-profile Tact Switch
KS & KSF Series Low-profile Tact Switch Features/enefits Low profile Protected against flux KS without top sealing KSF with top sealing RoHS compliant and compatible Typical Applications Low profile keyboards
More informationonlinecomponents.com
eatures/benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy terminal-seal compatible with bottom wash cleaning RoHS complaint models available Typical Applications
More information7000 Series Miniature Toggle Switches
Miniature Switches eatures/benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy terminal-seal compatible with bottom wash cleaning RoHS complaint models available
More informationAnti vandal switch.
Anti vandal switch www.langir.com Anti-vandal series comparison Cutout Diameter / Depth Functions available type Actuator options Dot illumination Ano diz e d Stainless s Gold plated brass Nickel plated
More informationQ19 series. Ø19 mm panel mount LED indicators DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS GENERAL SPECIFICATIONS MATERIALS MOUNTING
IND-Q19-17-07 LED INDICATORS DISTINCTIVE FEATURES 10 mm colored diffused epoxy lens or 10 mm water clear super bright LEDs Prominent and flush bezel styles (2.8 x 0.8) solder lug/faston terminals, pins
More informationSwitches- and Indicators
Switches- and Indicators Contents Description... 3 Product Assembly... 4 Mounting instruction... 6 Devices raised mounting... 7 Devices flush mounting... 9 Accessories... 11 Technical Data... 25 Drawings...
More informationHMI Components. Series. Indicator Illuminated pushbutton Mushroom-head pushbutton Key lock switch
Edition 10/2016 HMI Components Series Characteristics The compact Series is especially suited for: Flush design The large rectangular design (24x36mm) features a large illuminated area. Functions The Series
More informationSeries 300. Miniature Rocker & Paddle Switches
Series 00 SPECIFICATIS: CTACT RATING: Refer to "Contact Material Options" for more info. ELECTRICAL LIFE: 0,000 make-and-break cycles at full load. CTACT RESISTANCE: 0m max. inital @ -VDC. 00mA for both
More informationRoHS. Specifications. Part Number Configurator
Applications / Markets Audio / Visual Security Devices Industrial Controls Specifications Electrical Rating: 2A, 48VDC Electrical Life: 50,000 Cycles Contact Resistance: 50mΩ Max. Insulation Resistance:
More informationAttractive rugged rocker switch
istinctive features Attractive rugged rocker switch UG0AR Removable actuator Easy to stock Easy to customize Uptodate rocker design Smooth curves Wide choice of colours and symbols Laser etched symbols
More informationSwitches. Introduction
Introduction Switches Manufactured from, Bulgin s extensive range of vandal resistant security switches are designed with a high resistance to wear and tear, corrosion and harsh use in potentially hostile
More informationMINIATURE SWITCHES. Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action)
Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action) MINIATURE SWITCHES PS SERIES 5 AMP. (S.P.) 1 AMP (D.P.) 0.4 VA DIRECT PANEL MOUNT Basic P/N Terminal Type Poles Cap
More informationAPEM COMPONENTS LIMITED
APEM COMPONENTS LIMITED Designed and manufactured in the UK Illuminated pushbuttons and indicators, Keylock, Lever and Emergency Stop Switches APEM designs and manufactures three product lines: miniature
More informationC&K DA Series Miniature Single Pole Rocker Switches
Features/Benefits Typical Applications Nice actuator styling with Small appliances multiple options Computers and peripherals Guards to prevent accidental Medical instrumentation actuation Momentary and
More informationGeneral_technical_data Series
Emergency-stop Switching system The double-break switching system can be supplied for the following switching functions: 1 Normally closed, 2 Normally closed, 1 Normally closed + 1 Normally open. The Normally
More informationC&K 7000 Series Miniature Toggle Switches
Miniature Switches eatures/benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy sealed terminals prevent contamination during soldering Typical Applications Telecommunications
More informationMINIATURE SWITCHES. Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action)
Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action) MINIATURE SWITCHES PS SERIES 5 AMP. (S.P.) 1 AMP (D.P.) 0.4 VA DIRECT PANEL MOUNT ONE POLE TWO POLE Basic P/N Terminal
More informationDistinctive Characteristics
Distinctive Characteristics Subminiature size saves space on PC boards. Specifically developed for logic-level applications. ntistatic superstructure, consisting of the carbon impregnated bushing and the
More informationMini USB and USB 2.0-IP67 Connector System
Mini USB and USB 2.0-IP67 Connector System Section 12 Mini USB and USB 2.0-IP67 Connector System CONEC has added the Mini-USB connector. This Mini-USB IP67 receptacle and plug family, feature a bayonet
More informationDistinctive Characteristics
Distinctive Characteristics Various cap styles and colors to meet differing application needs. Bright, full face illumination to distinctively indicate status. Rear panel threaded mounting or snap-in mounter
More informationC&K E Series Sealed Miniature Toggle Switches
Features/Benefits Sealed against solder and cleaning process contaminants UL 94V-0 Nylon case and bushing Multi-positions ESD protection available RoHS compliant models available Typical Applications Telecommunications
More informationSMT T SERIES SURFACE MOUNT TINY SWITCHES Distinctive features
Distinctive features ENTIRELY DESIGNED FOR SURFCE MOUNT Surface mount devices (SMD) are subjected to more stringent constraints of temperature, solderability and space savings than through-hole components.
More informationA02 SERIES ILLUMINATED OR NON-ILLUMINATED PUSHBUTTON SWITCHES Panel cut-out Ø22 or 29.5 x 21.5
ILLUMINATED OR NON-ILLUMINATED PUSHBUTTON SWITCHES Panel cut-out Ø22 or 29.5 x 21.5 A pushbutton assembly requires: screen + lamp (if illuminated) + operator + one or two switchblocks To order these elements,
More informationDistinctive Characteristics
Distinctive Characteristics Full face or spot illumination with incandescent lamps or multi-element LEDs, with or without resistors. Choice of super bright LEDs in white, green, and blue as well as bright
More informationAvailable in a wide range of colours.
Prevent dust, sand and water from getting into switches. On toggle versions, also prevent ice from blocking lever action Compatible with frontal sealing options (K and X408). Available in a wide range
More informationToggles Product Selection Guide
s Product Selection Guide s Series 7000 Military E ET T GT 9000 Switch Type Miniature Miniature Miniature Subminiature Subminiature Ultraminiature Power Poles/Throws,, 3PDT, 4PDT,,,, 3PDT SPST,, SPST,,
More informationROTARY SWITCHES. Quality Features: LIGHTED ROTARY UP TO 3 POSITIONS WITH 3 OPTIONAL, INDEPENDENT LED LIGHT POSITIONS, 1.45 X.
SWITCH R2 UP TO 3 POSITIONS WITH 3 OPTIONAL, INDEPENDENT LED LIGHT POSITIONS, 1.45 X.83 PANEL CUTOUT Used in the heavy equipment, marine, process control and instrumentation markets the R2 rotary switch
More information1000 Series Miniature Slide Switches
Miniature Switches Features/Benefits Variety of actuators and terminations Panel mount tabs available Epoxy terminal seal compatible with bottom-wash cleaning RoHS compliant Typical Applications Test &
More informationQ16 series. Ø16 mm panel mount LED indicators DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS GENERAL SPECIFICATIONS MATERIALS MOUNTING
IND-Q16-17-07 LED INDICATORS DISTINCTIVE FEATURES Secret until lit polycarbonate decals or custom engraving 10 mm colored diffused epoxy lens or 10 mm water clear super bright LEDs (2.8 x 0.8) solder lug/faston
More informationSPECIFICATIONS: MATERIALS: If your preferred product configuration is not shown, please contact our sales representative for custom design.
SPECIFICATIS: CTACT RATING: Refer to "Contact Material Options" for more info. ELECTRICAL LIFE: 50,000 make-and-break cycles at full load. CTACT RESISTANCE: 0m max. initial @2-4VDC 00mA for both silver
More information