Vintage Westinghouse panelboards

Transcription

1 Supersedes February 9 PRL1-LX PRL1 / PRL2 PRL CDP, HCDP FDP Contents Description Page Procedure for identifying renewal parts Distributor ordering instructions PRL PRL PRL PRL1-LX, PRL-LX CDP, HCDP Breaker cross-reference FDP Trim locks Trim clamps Sumter aftermarket services

2 Procedure for identifying renewal parts 1. Identify the type of panelboard (PRL1, PRL2, PRL, PRL1-LX, PRL-LX, CPD, FDP) from the data found on the nameplate. Critical information includes: Type of panelboard Ampere rating of the main Ampere rating of the neutral Voltage Type of service (phase/number of wires) General order number 2. Refer to the listing below and turn to the proper section in this renewal parts data to identify standard parts and components. Description Page PRL1 and PRL PRL PRL1-LX, PRL-LX CDP, HCDP Breaker cross-reference Series C/Energy Sentinel FDP Trim locks Trim clamps This book identifies those replacement parts most frequently ordered and which are readily available from stock. These parts can be ordered by style or catalog number to speed up processing and delivery. 4. In the event the nameplate is missing, it may still be possible to identify the panel type by the location of the neutral bar. Figure 1 below shows the position of the neutral in the panelboard. Box width may also be used to help identify the panelboard type. Standard width for PRL1, PRL2 and PRL is inches (508.0 mm). CDP, FDP standard widths are 0.00, 8.00, 42.00, and inches (762.0, 9.2, 66.8, and mm). CAUTION! HAZARDOUS VOLTAGE WILL CAUSE SEVERE INJURY OR DEATH. TURN OFF POWER SUPPLY TO EQUIPMENT BEFORE WORKING ON IT. Distributor ordering instructions 1. Specify the part by catalog number 2. Refer to PL E for pricing information. Discount Symbol CE9 applies. Enter the order on Vista, location Q49 or SUM Note: For CDP retrofit kits shown on page 12, you must enter the catalog number, list price, standard multiplier and location Q49 or SUM. 4. When ordering a new circuit breaker to add to a CDP panelboard, the following options are available: Take the required breaker from your stock (or order from W4) and order the connector kit (pages 14 and 18) from the Sumter Plant or Select the correct breaker retrofit kit (page 12) which includes the breaker and connector kit in one package, one shipment and one invoice from the Sumter Plant 5. Selling policy applies 6. If additional support is required, contact the Sumter Plant Aftermarket Center at A complete listing of available services is listed on page 20 Neutral Gutter Pow-R-Line 1,2 Main Gutter Pow-R-Line Gutter CDP, FDP Figure 1. Panelboard neutral locations 2

3 Renewal Parts RP E PRL1 and PRL2 Table 1. Replacement connectors Panel type Catalog number PRL1 KPRL1BAB PRL2 KPRL2GHB PRL1 without trim Nameplate Ground bar Deadfront cover Neutral bar Box PRL1 and PRL2 Trim Replacement connectors for PRL1 and PRL2 Replacement connectors for PRL1 and PRL2 PRL2 with trim Each kit contains two sets of A, B, and C phase connectors, phase isolators, hardware and instructions for mounting up to 12 poles. Silver-plated copper connectors are suitable for use with copper or aluminum bus. Maximum amperes connected to any one connector cannot exceed 140A. Replacement boxes and trims for PRL1 and PRL2 Standard box and trim sizes are shown in Table 2. For other sizes, contact your local Satellite. For Type 12/R enclosures, refer to page 8. Trim mounting may be either surface or flush. Flush trims overlap the box by 0.75-inch (19.1 mm) on all sides. Denote on order by using either S or F in the catalog number. Table 2. Replacement boxes and trims Box dimensions in inches (mm) Type 1 Catalog number Height Width Depth Box Trim (5.4) (609.6) (685.8) 0.00 (762.0).00 (88.2) 6.00 (914.4) 9.00 (990.6) (66.8) (114.0) (1219.2) (1295.4) (171.6) (1447.8) (1524.0) 6.00 (1.2) (1676.4) (1752.6) (1828.8) (1905.0) (1981.2) (2057.4) (21.6) (2209.8) (2286.0) (508.0) 5.75 (146.1) YS2021 YS2024 YS2027 YS200 YS20 YS206 YS209 YS2042 YS2045 YS2048 YS2051 YS2054 YS2057 YS2060 YS206 YS2066 YS2069 YS2072 YS2075 YS2078 YS2081 YS2084 YS2087 YS2090 LT2021S/F LT2024S/F LT2027S/F LT200S/F LT20S/F LT206S/F LT209S/F LT2042S/F LT2045S/F LT2048S/F LT2051S/F LT2054S/F LT2057S/F LT2060S/F LT206S/F LT2066S/F LT2069S/F LT2072S/F LT2075S/F LT2078S/F LT2081S/F LT2084S/F LT2087S/F LT2090S/F

4 PRL1 and PRL2 0A neutral bar Branch section deadfront covers PRL1 PRL2 0A neutral bar Table. 0A neutral bar Description Style number A Boxes 0.00 inches (762.0 mm) and above 5158C0G02 B Boxes less than 0.00 inches (762.0 mm) high 5158C0G01 225A neutral bar Branch section deadfront covers Blank covers 225A neutral bar Table A neutral bar Description Style number A Boxes 0.00 inches (762.0 mm) and above 5158C0G04 B Boxes less than 0.00 inches (762.0 mm) high 5158C0G0 Blank covers Table 4. Blank covers Blank covers height in inches (mm) Style number A (81.0) 456B99H05 B.00 (76.2) 456B99H01 C 6.00 (152.4) 456B5H01 4

5 Renewal Parts RP E Standard ground bar Table /A neutral bar Description Style number 400/A neutral bar 5158C04G01 Isolated ground bar Standard ground bar Table 6. Standard ground bar Description Style number A Boxes 0.00 inches (762.0 mm) and above 5158C05G02 B Boxes less than 0.00 inches (762.0 mm) high 5158C05G01 400/A neutral bar Isolated ground bar Table 8. Isolated ground bar Description Style number A Boxes 0.00 inches (762.0 mm) and above 5158C05G06 B Boxes less than 0.00 inches (762.0 mm) high 5158C05G05 Table 9. PRL1, PRL2 branch section deadfront covers Maximum number of circuits Cover height in inches (mm) Cover style number PRL1 PRL (254.0) 1.00 (0.2) (406.4) 5156CH CH CH0 5156C09H C09H C09H0 400/A neutral bar (482.6) (558.8) (65.0) 5156CH CH CH C09H C09H C09H (711.2) 1.00 (787.4) 4.00 (86.6) 5156CH CH CH C09H C09H C09H09 5

6 PRL Table. Standard ground bar Description Style number A Boxes 0.00 inches (762.0 mm) and above 5158C05G02 B Boxes less than 0.00 inches (762.0 mm) high 5158C05G01 Nameplate Replacement boxes and trims for PRL Ground bar Filler plate Chassis Standard boxes and trim sizes are shown in Table 11. For other sizes, contact your local Satellite. For Type 12/R enclosures, refer to page 8. Trim mounting may be either surface or flush. Denote on the order by using either S or F in the catalog number. Flush trims overlap the box by 0.75-inch (19.1 mm) on all sides. Table 11. Replacement boxes and trims Box dimensions in inches (mm) Type 1 Box Trim Catalog number Height Width Depth Box Trim Standard ground bar PRL 0.00 (762.0) 6.00 (914.4) (66.8) (1219.2) (171.6) (1524.0) (1676.4) (508.0) 5.75 (146.1) YS200 YS206 YS2042 YS2048 YS2054 YS2060 YS2066 LTT200S/F LTT206S/F LTT2042S/F LTT2048S/F LTT2054S/F LTT2060S/F LTT2066S/F (1828.8) (1981.2) (21.6) (2286.0) YS2072 YS2078 YS2084 YS2090 LTT2072S/F LTT2078S/F LTT2084S/F LTT2090S/F Standard ground bar 6

7 Renewal Parts RP E PRL Replacement connectors for EHD, FDB, FD, HFD, and FDC breakers (240, 480, V) Kit contains A, B and C phase connectors, hardware and instructions to twin mount two -pole above listed frame breakers. Maximum amperes per breaker not to exceed 150A, and maximum amperes connected to any one connector not to exceed A. (50 150As.) Table 1. Replacement connectors for ED, EDH, and EDC breakers Replacement connectors for breakers ED, EDH, and EDC Catalog number KPRLED Replacement connectors for CA, CAH, and HCA breakers Kit contains A, B, and C phase connectors, hardware, cover and instructions to mount one 2- or -pole CA frame breaker. Replacement connectors for EHD, FDB, FD, HFD and FDC breakers Table 12. Replacement connectors for EHD, FDB, FD, HFD, and FDC breakers Replacement connectors for breakers EHD, FDB, FD, HFD, and FDC Catalog number KPRLFD Replacement connectors for ED, EDH, and EDC breakers Kit contains A, B, and C phase connectors, hardware cover and instructions to mount one -pole above breaker frame. (240V maximum.) Replacement connectors for CA, CAH, and HCA breakers Table 14. Replacement connectors for CA, CAH, and HCA breakers Replacement connectors for breakers CA, CAH, and HCA Catalog number KPRLCA Note: The PRL connector kits will fit the following : WEB, WCA, WEHB, WFB, and HWFB. Space for BAB frame breaker 225A neutral Replacement connectors for ED, EDH, and EDC breakers PRL1 subchassis EHD, ED frame breaker is single mount only Space for EHD frame breaker CA frame breaker Space for CA frame breaker 225 MLO PRL interior 7

8 PRL1, special trims and enclosures Ventilated trim Required on PRL1 and PRL2, A panels only. Order by adding the letter V to the standard trim catalog number. ADD percent TO STANDARD TRIM LIST PRICE. Example: LT2072S becomes LTV2072S. Refer to page for the standard trim catalog numbers. Fastrim Ventilated trim Door-in-door trim Piano hinge on the right side of the trim provides access to the wiring gutters without requiring removal of the trim. Order by adding the letters DD to the standard trim catalog number. ADD 20 percent TO STANDARD TRIM LIST PRICE. Example: LT2072S becomes LTDD2072S. Refer to pages and 5 for standard trim catalog numbers. Type 12/R enclosures Door-in-door trim Fastrim Type 12/R enclosures Used when concealed trim mounting hardware is required for PRL1, PRL2, and PRL. Flush trim utilizes Style Number 414A80G01 trim clamps. Surface trim utilizes Style Number 8712C7H01 trim clamps. Trim clamps are included and shipped with the trim. Order by adding the letter F to the standard trim catalog number. ADD 20 percent TO STANDARD TRIM LIST PRICE. Example: LT2072S becomes LTF2072S. Refer to pages and 5 for standard trim catalog numbers. The complete enclosure consists of a box and trim. The enclosure meets code requirements for both Type 12 (dust-tight) and Type R (rainproof) standards. Features include a laser cut trim with rounded corners, concealed hinges, and a T-handle lock. Gasketing is provided around the trim door. The gasketed box is made of code gauge steel with dripshield and is painted ANSI-61. Table 15. Type 12/R enclosures for PRL1, Box dimensions in inches (mm) Catalog number Height Width Depth Box PRL1, 2 trim PRL trim (609.6) 6.00 (914.4) (1219.2) (1524.0) (1828.8) (1981.2) (508.0) 6.00 (152.4) GWPB2024 GWPB206 GWPB2048 GWPB2060 GWPB2072 GWPB2078 LWPT2024 LWPT206 LWPT2048 LWPT2060 LWPT2072 LWPT2078 LWT206 LWT2048 LWT2060 LWT2072 LWT2078 8

9 Renewal Parts RP E Column-type panels PRL1-LX replacement boxes and trims Standard box includes box ends at top and bottom Box for trough is supplied with bottom box end only Contact the Sumter Plant Aftermarket Center for availability and application information Table 16. Column-type panels Box dimensions in inches (mm) Catalog number Height Width Depth Standard box Box for trough (66.8) (171.6) (1676.4) (1981.2) 8.6 (219.2) 5.00 (127.0) 114D99G 114D99G12 114D99G14 114D99G16 114D99G26 114D99G28 114D99G0 114D99G2 Surface trim 6724D78G 6724D78G D78G D78G16 PRL-LX replacement boxes and trims Standard box includes box ends at top and bottom Box for trough is supplied with bottom box end only Design is for top feed application only Contact the Sumter Plant Aftermarket Center for availability and application information Table 17. PRL-LX replacement boxes and trims Box dimensions in inches (mm) Catalog number Height Width Depth Standard box Main lug only (top feed) (5.1) (1244.6) (1454.2).50 (166.7) 7.75 (187.) (2082.8) Main breaker (top feed) (114.5) (1524.0) (17.6) (144.1) (2152.7) 9.00 (262.2) 8.6 (219.2) 5.75 (146.1) 6726D69G D69G D69G0 6726D69G D69G D69G (219.2) 5.75 (146.1) 6726D69G1 6726D69G D69G D69G D69G D69G18 Box for trough 6726D69G D69G D69G D69G 6726D69G D69G D69G D69G D69G D69G D69G2 6726D69G24 Surface trim 6726D70G D70G D70G0 6726D70G D70G D70G D70G D70G D70G D70G 6726D70G D70G12 9

10 CDP/HCDP Chassis rail Chassis bus Breaker mounting bracket Copper connectors Original F-frame breaker Filler plate Breaker mounting bracket Upgraded series C breaker Filler cover Filler cover mounting bracket Nameplate CDP/HCDP panelboard

11 Renewal Parts RP E Branch circuit breaker selection Step 1: Select the correct breaker. When selecting a breaker, you need to know the following: Amperage System voltage Available short circuit rating Number of poles Size and number of wires per phase Step 2: Use the chart on page 14 to determine the space required. Step : Create the Retrofit Kit catalog number by following the instructions on page 12. Step 4: Determine if extra filler covers are required. Additional filler covers may be necessary to fill the unused space. Refer to page 14 for this information. Note: If the CDP panelboard has a subchassis lighting panel, contact the Sumter Plant Aftermarket Center for breaker selection. Table 18. Electrical characteristics of branch circuit breakers Circuit breaker type EHD ED EDH EDC FDB FD HFD FDC CA CAH HCA JD, JDB HJD JDC DK KD, KDB HKD KDC Continuous ampere rating Number of poles Vac UL listed interrupting capacitieska symmetrical amperes AC rating volts DC rating volts LCL LD HLD LDC MDL HMDL ND HND NDC Fused circuit breakers with LFB current limiters FDB, LFB , TRI-PAC integrally fused, current limiting circuit breakers FB-P LA-P NB-P DC ratings apply to substantially non-inductive circuits. Not recommended for motor loads. DC ratings not available with electronic trip. 0K based on NEMA test procedure

12 CDP CDP breaker retrofit kits A retrofit kit includes one breaker and all the associated parts required for mounting on a CDP panel chassis. See Table 19 below. Table 19. CDP breaker retrofit kits Frame ampere rating Breaker frame 0 EHD EHD FDB FDB FD FD HFD HFD FDC FDC FCL FB-P 225 FDB FD HFD FDC ED EDH EDC 250 JD JD HJD HJD JDC JDC 400 KD HKD KDC LCL LA-P LD HLD LDC 800 MDL HMDL HND 1 ND HND NDC Trip ampere range Mounting type Single Single Single Single Single Single Space required Inches (mm) 4.1 (4.9) X 4.1 (4.9) X 4.1 (4.9) X 5.50 (19.7) 8.25 (209.6) 8.25 (209.6) X space 4X 6X 6X 8.25 (209.6) 6X 8.25 (209.6) 6X 8.25 (209.6) 6X How to create a retrofit kit catalog number Use KCDP prefix and add the catalog number of the specific breaker as shown in Table 20. mounting indicates that only one set of connectors is required to mount two breakers (of similar frames) opposite one another. A RETROFIT KIT INCLUDES ONE BREAKER ONLY, FOR EITHER SINGLE OR TWIN MOUNTED APPLICATIONS. If a second breaker is required for a twin mounting application, it must be specified as a separate item. Example: The retrofit kit catalog number for a -pole, 400A KD breaker is: Table 20. Catalog numbering system Designates CDP connector kit KCDP KD 400 Breaker frame CDP retrofit kit Each kit includes one breaker, copper connectors, mounting brackets, covers, hardware and instructions. CDP retrofit kit Number of poles 2 = 2-pole = -pole Ampere rating 12

13 Renewal Parts RP E Breaker cross-reference chart Use the chart below to cross-reference older industrial type Westinghouse breakers with Series CT breakers. The Series C breakers shown on the right side of the chart use the same X space as the older breaker on the left, eliminating the need for any filler covers when retrofitting a CDP panel. By using the retrofit kit catalog number, you can order the breaker, as well as the corresponding CDP connector kit in one easy step. Note: If the original space was already provided with connectors and hardware to mount the older breakers, then the Series C frames shown here will also fit in that same provision. (The Series C K family of breakers requires an adapter kit called TAD when mounting a KD frame breaker onto existing LB frame connectors. This adapter kit is included in orders for either KD retrofit kits or connector kits, but may also be purchased separately for use with existing LB connectors.) Table 21. Breaker cross-reference chart Existing breaker Breaker frame EB EHB FB HFB KA HKA KB HKB JA JB DA LA HLA LB LBB HLB LC HLC MA HMA MC NB HNB NC HNC Continuous ampere rating Order Series C retrofit kit Breaker frame EHD EHD FDB FD KD HKD JD JD KDB JDB DK LD LD KD KDB KD LD LD MDL MDL MDL ND ND ND ND Retrofit kit catalog number KCDPEHD KCDPEHD KCDPFDB KCDPFD KCDPKD KCDPHKD KCDPJD KCDPJD KCDPKDB KCDPJDB KCDPDK KCDPLD KCDPLD KCDPKD KCDPKDB KCDPKD KCDPLD KCDPLD KCDPMDL KCDPMDL KCDPMDL KCDPND KCDPND KCDPND KCDPND 1

14 CDP CDP breaker connector kits A connector kit consists of copper connectors, mounting brackets, covers, hardware, and instructions for mounting breaker(s) on a CDP chassis. See below. If breaker is also required, see retrofit kits shown on page 12. Connector kit Each kit includes copper connectors, mounting brackets, covers, hardware, and instructions. Hardware kit Each kit includes mounting bracket(s), filler plates and mounting hardware ONLY. Use the appropriate connector kit catalog number and add an H to designate hardware only. Example: KCDPFD0H Hardware kit Table 22. CDP Breaker frames EHD, FDB, FD, HFD, FDC FD, FDB, HFD, FDC, ED, EDH, EDC FB-P, FCL CA, CAH, HCA JD, JDB, HJD, JDC Number of poles Connector kit Mounting type Space required Inches (mm) X space Connector kit catalog numbers 4.1 (4.9) X KCDPFB0 KCDPED225 KCDPFBP KCDPCA KCDPKB DK, KD, KDB, HKD, KDC 5.50 (19.7) 4X KCDPLB LA-P LD, HLD, LDC LCL MDL, HMDL ND, HND NB-P Single Single Single Single 8.25 (209.6) 6X KCDPLA400 KCDPLA KCDPLCL KCDPMC KCDPNC KCDPNBP CDP filler covers Filler covers are available in any increment of 1X 1.8 inches (5.1 mm). Catalog number is: KCDP_ X. Fill in the blank with the size. Included are cover, mounting brackets, and hardware. CDP filler covers 0A maximum. Connector kits are not rated for 0 percent breakers. 14

15 Renewal Parts RP E Energy submetering for existing CDP The IQ Energy Sentinel is a submetering device that mounts directly on a Series C circuit breaker and can be retrofitted into a CDP panelboard. It monitors both power and energy from 15 to 400A, with an overall accuracy of 99 percent. This high system accuracy is achieved by use of the Cutler-Hammer SURE Plus Chip, which is a sophisticated microprocessor. All that is necessary to complete an IQ Energy Sentinel installation is to insert it into the load side of a breaker; feed the load conductors through it; connect a neutral wire; and run the shielded twisted pair wire for communications. The IQ Energy Sentinel has a nonvolatile memory, is powered by the circuit breaker, and can be applied on -phase, four-wire or 1-phase, three-wire systems. The space-saving design characteristics of the IQ Energy Sentinels means they can be quickly and easily retrofitted onto Series C circuit breakers in existing equipment with no additional space required. Additionally, IQ Energy Sentinels can be installed when upgrading to Series C from older breakers that are physically interchangeable with no additional space requirements. Power and energy information from IQ Energy Sentinels can be communicated to a personal computer, a panel-mounted central energy display (CED), or even existing building management or distribution control systems. Series C breakers with energy sentinel Series C breakers with energy sentinel Retrofit capabilities With the advent of this new technology, we can offer the capability to retrofit existing CDP. This is accomplished by providing a complete system package including: Series C breaker retrofit kit Energy Sentinel All necessary wiring diagrams and mounting instructions Start-up assistance Communications capabilities with one of the following: IQ Central Energy Display Custom Billing Software Package IMPACC/PowerNet CDP chassis with energy sentinel 15

16 FDP Nameplate Extension wings Extension wings Copper connectors Chassis rail Chassis bus Filler cover FDP panelboard 16

17 Renewal Parts RP E FDP Branch FDPW and FDPB Switch selection Step 1: Once you know the amperage and system voltage, choose the retrofit kit catalog number from Table 2. Step 2: Check for space requirements from Table 2. Step : Determine if extra filler covers are required. Additional filler covers may be necessary to fill the unused space. Retrofit kit Each kit includes one switch, copper connectors, covers, hardware and instructions. FDPW and FDPB retrofit kits A retrofit kit includes the switch and all the associated parts required for mounting on a FDP panel chassis. Switches through A are designed for use with rejection type fuses. For other fuse applications, contact the Sumter Plant Aftermarket Center. Switches rated 800 and 1A are designed for use with Class L fuses. Fuses are not included. Table 2. P retrofit kits Space required Switch ampere Catalog number Inches (mm) X space rating 240V V 5.50 (19.7) 4X KFDPWT211R KFDPWT222R KFDPWT2R KFDPWT611R KFDPWT622R 6.88 (174.8) 5X 0 0 KFDPWT6R 8.25 (209.6) 12.8 (14.5) 15.1 (84.) 15.1 (84.) 20.6 (524.0) 6X 9X 11X 11X 15X KFDPBS24R KFDPW25R KFDPW26R KFDPW67 KFDPW68 KFDPBS64R KFDPWR KFDPW66R KFDPW67 KFDPW68 Retrofit kit FDP filler covers Filler covers are available in any increment of 1X 1.8 inches (5.1 mm). Catalog number is: KFDP_ X. Fill in the blank with the size. Included are cover, mounting brackets and hardware. Switch connector and retrofit kits FDPW or FDPB switch connector kits and retrofit kits to be installed in vintage Westinghouse FDP and switchboards. Vertical bus bars must on.50 inch (88.9 mm) center-line phase to phase. See Figure 2. Note: If bus bar spacing is 4.25 inches (8.0 mm), these switches will not fit and no parts are available. Vertical bus bar 1.8" TYP..50".50" FDP filler cover MTG. rails 19.50" Figure 2. Switch connector and retrofit kits Note: Dimensions shown apply to CDP and FDP chasis. 17

18 FDP FDPW and FDPB connector kits Each kit includes copper connectors, extension wings (when required), hardware and instructions to mount one FDPW or FDPB switch on a FDP panel chassis. Connector kit Each kit includes copper connectors, mounting brackets, covers, hardware, and instructions. Table 24. FDP Space required Inches (mm) X space Switch ampere rating 5.50 (19.7) 4X Catalog number -pole FDPW and FDPB 240V FDPWT211R FDPWT222R FDPWT2R V FDPWT611R FDPWT622R Connector kit KFDP4XT 6.88 (174.8) 5X 0 0 FDPWT6R KFDP5XT 8.25 (209.6) 12.8 (14.5) 15.1 (84.) 15.1 (84.) 20.6 (524.0) 6X 9X 11X 11X 15X FDPBS24R FDPW25R FDPW26R FDPW67 FDPW68 FDPBS64R FDPWR FDPW66R FDPW67 FDPW68 KFDPB6X-2 KFDPW9X-4 KFDPW11X-6 KFDPW11X-8 KFDPW15X-12 Connector kit Picture frame To permit installation of circuit breakers in a FDP panel, a picture frame is required. Add 2X to the breaker size for transition. Contact the Sumter Plant for technical assistance and pricing at Picture frame 18

19 Renewal Parts RP E Panelboard trim locks Note: Dimensions in inches (mm). Replacement panelboard trim clamps.00 (76.2).00 (76.2) 1.8 (5.1) 1.8 (5.1) 2.50 (6.5) K C62H No Longer Available 4.56 (115.8) 5.1 (10.).6 (92.2) 414A80G (26.9) (57.2) (1.8) 114C247G01 457B16G C81G01 Overall length of 2.50 inches (6.5 mm) Used on CDP, FDP, and NQB Table 25. Panelboard trim locks Description For use on left-handed door (hinged on the left side). For use on right-handed door (hinged on the right side). T handle lockat one time used on all panels over inches ( mm) in height. Also used on outdoor (NR) panels. Used on lighting and small power panels as standard. Replacement lock uses WEM- key. Used on lighting and small panels as standard. This is the present-day lock used on standard PRL1, 2, and s. WEM 2 key. Catalog/style number K C62H C247G01 457B16G C81G01 Contact the Sumter Plant Aftermarket Center for prices and details at A11G02 Overall length of.1 inches (79.5 mm) Used on BB and PRL1, These trim clamps are used to mount FASTRIMS. This type of trim used to be supplied as standard on all panels, and is still available today when concealed trim mounting hardware is specified. They come in bags of six. Please note that some larger panels may require more than one bag. 19

20 Sumter aftermarket services All the parts and kits shown in this Renewal Parts data will come from the Sumter Plant Aftermarket Center (order entry location Q49 or SUM). To extend the life of your existing equipment, the Sumter Aftermarket group will: Provide all new components Manufacture per original specifications Follow UL procedures Provide full Cutler-Hammer warranty Services offered include: Parts and kits for CDP and FDP Retrofit kits for WF and WRP distribution sections Connector kits for WF and WRP distribution sections Emergency service WARNING! HAZARDOUS VOLTAGE WILL CAUSE SEVERE INJURY OR DEATH. TURN OFF POWER SUPPLY TO EQUIPMENT BEFORE WORKING ON IT. NEMA is the registered trademark and service mark of the National Electrical Manufacturers Association. UL is a federally registered trademark of Underwriters Laboratories Inc. Additional services Since virtually all are supplied to meet specific customer requirements, other parts not listed in this publication might occasionally be needed. Price and availability for parts not shown here may be obtained by contacting the Sumter Plant Aftermarket Center ( ) and providing a complete description of the part, along with the data on the panelboard nameplate. Should you experience difficulty in determining what replacement parts are needed, contact the Sumter Aftermarket Center, who can provide help to: Identify and recommend replacement parts Verify the correct connector kits which should be ordered for each circuit breaker or fusible switch Provide a recommended spare parts list Eaton Corporation Electrical Group 00 Cherrington Parkway Moon Township, PA 158 United States 877-ETN-CARE ( ) Eaton.com 9 Eaton Corporation All Rights Reserved Printed in USA Publication No. RP E / Z8499 April 9 PowerChain Management is a registered trademark of Eaton Corporation. All other trademarks are property of their respective owners.