RCS1000 Data Sheet. RCS1000 Series Controllable Circuit Breaker Panel

Transcription

1 RCS000 Series Controllable Circuit Breaker Panel RCS000 Data Sheet Overview The RCS000 Series Controllable Circuit Breaker Panels combines the benefi ts of traditional relay based load control and the benefi ts of circuit protection into a single panel assembly. This solution substantially reduces the installation time and the equipment foot-print over a separately mounted standard panelboard and relay panel. RCS000 Series Features Meets or exceeds NEC0-0 Ships within weeks Single point load termination, no need for interconnect wiring Factory mounted or remote mounted controller Low voltage controller electronics are isolated from high voltage Network ready for TRIATEK Lighting s Web-based BASnet LightView or integration to most Building Automation Systems (BAS) No limitation on the placement of remote-control circuit breakers within a panelboard Controller can be mounted up to 50 feet from remote-control circuit breakers Up to 4 remote-control circuit breakers per panelboard Mix standard breakers and remote-control breakers in the same panel Up to 60 remote-control circuit breakers per controller Optional LEXP-RCS on-board expansion for additional programmable inputs Optional Digi-Touch Control board (on-board expansion) for a Digi-Touch Network RCS000 Lower total installed cost* VS. Standard Circuit Breaker Panel Relay Panel Interconnect wiring Higher total installed cost* *Total installed cost = material + labor RCS000 with RCS-FM (Factory Mounted Controller) The panelboard section can be provided with a Main Lug or Main Breaker. All branch circuit breakers shall be installed per the Ordering Chart (see page 6) prior to shipment. The controller, RCS-FM, shall be factory mounted to the panelboard at the end opposite the Main feed (top feed is pictured). The control harness between the controller and each remote-control circuit breaker shall be factory wired. RCS000 with RCS-FM RCS-FM Benefits Ready to install, no fi eld wiring between controller and remote-control circuit breakers Single point of load termination RCS000 with RCS-RM (Remote Mounted Controller) The panelboard section can be provided with a Main Lug or Main Breaker. All branch circuit breakers will be installed per the Ordering Chart (see page 6) prior to shipment. The controller, RCS-RM, is shipped separately for fi eld mounting up to 50 feet / 5.5 meters from any remote-control circuit breaker. The control harness between the controller and each remote-control circuit breaker shall be provided by the installing contractor per TRIATEK Lighting s specifi cations. Crimping tool and connector kit can be ordered from TRIATEK Lighting. RCS000 with RCS-RM* For added fl exibility, the RCS-FM can be used to remotely control circuit breakers in other manufacturers panelboard enclosures, making it a great choice for retrofi t applications. Contact your factory representative for more details. RCS-RM Benefits Great for retrofi t applications Reduced installation over relay panels Controller can be mounted up to 50 feet / 5.5 meters from any remote-control circuit breaker Single point of load termination /8/005 *Parts displayed. Trim not shown Page of 6 TRIATEK Lighting 05 Cobb Place Blvd. Suite 00 Kennesaw, GA

2 RCS000 Data Sheet Specifications Electrical Controller Power Standard Inputs Optional Inputs Input types Output (Max) Breakers Ratings Panelboard Ratings Certifications Panelboard/Enclosure Circuit Breakers Controller / System Installation Environmental Operating Temperature Operating Humidity 0/77VAC, 40VA, ± 0%, 60 Hz (Dual Primary), or 47 VAC, 40VA, ± 0%, 60 Hz 4 programmable ( wire) or programmable ( wire), analog ( wire) for LS5 Photocell programmable ( wire) or 6 programmable ( wire), Requires LEXP-RCS added to panel Programmable for wire momentary, wire maintained, wire momentary, and Linked On; Field confi gurable jumper for dry contact or 4VDC signaling, one jumper for every group of 8 inputs 60 remote-control circuit breakers Fully rated 4K 77/480 or 65K 0/08 (For Series Rating contact factory) 0/08Y P4W up to A MLO or MB; 77/480Y P4W up to A MLO or MB UL 67/UL 50 UL 489 UL 96, New York City Approved #7908, CSA, CEC Approved Meets or exceeds National Electric Code 0º to 5º F 0% - 95% RH, Non-condensing Ordering Instructions for RCS000 with RCS-FM Step : Select Interior RCS - - SYSTEM VOLTAGE (A) - ø, 4 WIRE, 77/480V (B) - ø, 4 WIRE, 0/08V MAIN DEVICE TYPE L (5A MLO) L4 (A MLO) M (5A MB & BELOW) M4 (50-A MB) MOUNT ST - SURFACE TOP FED SB - SURFACE BOTTOM FED FT* - FLUSH TOP FED FB* - FLUSH BOTTOM FED CIRCUIT CAPACITY TRIP RATING RCSB-L-000-4ST *RCSFK - Flush Mount Kit (Can be ordered for all RCS000 models). Includes fl ush mount controller cover and fl ush mounting brackets. Mounts to the RCS-FM Controller. Flush Mount Cover Mounting Brackets = ø, 4 wire, 0/08V, 5A Main Lug Only, 4 circuit interior for top feed, surface mount application RCSFK Step : Select Controller Controller RCS-FM - Includes controller, controller enclosure, controller cover, and mounting hardware. Factory mounted as shown. Mounting Hardware RCS-FM factory mounted to panelboard enclosure /8/005 Page of 6 TRIATEK Lighting 05 Cobb Place Blvd. Suite 00 Kennesaw, GA

3 RCS000 Data Sheet Step : Select Circuit Breakers Note: Use charts on page 6 to select breaker types and locations in the panelboard. RCB00 RCB00 B00 B050 Remote-Control Circuit Breakers Standard Circuit Breakers Step 4: Select Options Switch Input s LEXP-RCS - Factory mounted Expansion Board Digital Device Network Controller DDN-L - Factory mounted to the RCS Controller. Required when using DDN-SW switches LEXP-RCS DDN-L Module Ordering Instructions for RCS000 with RCS-RM Step : Select Interior RCS - - SYSTEM VOLTAGE (A) - ø, 4 WIRE, 77/480V (B) - ø, 4 WIRE, 0/08V MAIN DEVICE TYPE L (5A MLO) L4 (A MLO) M (5A MB & BELOW) M4 (50-A MB) MOUNT ST - SURFACE TOP FED SB - SURFACE BOTTOM FED FT*- FLUSH TOP FED FB* - FLUSH BOTTOM FED CIRCUIT CAPACITY TRIP RATING RCSB-L-000-4ST *RCSFK - Flush Mount Kit (Can be ordered for all RCS000 models). Includes fl ush mount controller cover and fl ush mounting brackets. Mounts to the RCS000 Controller. Flush Mount Cover Mounting Brackets = ø, 4 wire, 0/08V, 5A Main Lug Only, 4 circuit interior for top feed, surface mount application /8/005 Page of 6 TRIATEK Lighting 05 Cobb Place Blvd. Suite 00 Kennesaw, GA

4 RCS000 Data Sheet Step : Select Enclosure Enclosure size depends on interior selected in Step. Use the Enclosure Selection Chart to select the correct enclosure. Enclosures* RCS-E48-48" High, enclosure only - NEMA RCS-E7-7" High, enclosure only - NEMA Enclosure Selection Chart MB/MLO 8 Circuit 0 Circuit 4 Circuit 0-5A RCS-E48 RCS-E48 RCS-E48 50-A RCS-E7 RCS-E7 RCS-E7 *The enclosures ordered here are shipped ahead of the interior. The interior will arrive in its enclosure as it is the preferred protection method during shipping. RCS-E48 Step : Select Controller Controller RCS-RM* - Includes controller, controller enclosure, and controller cover RCS-RM (cover not shown) *Note: Circuit breaker control wiring and mounting hardware are supplied by others. Each remote-control breaker requires a wire connection (0 AWG stranded 600V insulation). It is recommended that each RCS-RM is ordered with () RCSCK and that () RCSCT be ordered for every (0) panels. The connector kit (RCSCK) and one crimping tool (RCSCT) can be ordered from TRIATEK Lighting (For more information refer to RCS000 Installation Guide). Required Tools and Kits RCSCK - 0 connectors ( pin) RCSCT - Wire crimping tool RCSCK connector RCSCT Step 4: Select Circuit Breakers Use charts on page 6 to select breaker types and locations in the panelboard. RCB00 RCB00 B00 B050 Step 5: Select Options Remote-Control Circuit Breakers Standard Circuit Breakers Switch Input s LEXP-RCS - Factory mounted Digi-Touch Control Board Factory mounted to the RCS Controller. Required when using Digi-Touch Addressable / Networkable switches LEXP-RCS DDN-L Module /8/005 Page 4 of 6 TRIATEK Lighting 05 Cobb Place Blvd. Suite 00 Kennesaw, GA

5 RCS000 Data Sheet Dimensions RCS000 with RCS-FM RCS000 with RCS-RM Enclosure Heights (Inches) based on Circuit Capacity and Main Breaker / Main Lug Only Amperage MB/MLO 8 Circuit 0 Circuit 4 Circuit 0-5A A ¼" 8" Note: Circuit breaker panel enclosure and controller enclosure depth = 5 ¾" 8" 0 ¼" 0 ¼" Panel Layout 4 Remote-Control Circuit Breakers shown 4 Circuit Copper Interior Bus shown with deadfront cover Ground Bar Neutral Bar Controller Mounting Hardware LEXP-RCS DDN-L Module Circuit Breaker Remote- Control Wiring Removable Backplane RCS Controller Controller Power Supply System Diagram Main line voltage (top feed) Branch circuit wiring Example RCS000 with RCS-FM Application Applies to all breaker panels in the diagram. RS-485 Network to BASnet LightView or Building Automation System Example RCS000 with RCS-RM Application RS-485 Network to BASnet LightView or Building Automation System Up to 56 switch inputs Up to 56 switch inputs /8/005 Circuit breaker panel with 0 remote-control and standard circuit breakers Controller electronics (low voltage electronics are isolated from high voltage wires). Controls up to 60 remote-control circuit breakers Circuit breaker control wiring up to 50 feet TRIATEK Lighting 05 Cobb Place Blvd. Suite 00 Kennesaw, GA Page 5 of 6

6 RCS000 Data Sheet Circuit Breaker Ordering Chart Circuit Breaker Ordering Chart R/S Breaker Circuit Circuit Breaker R/S To complete the Circuit Breaker Ordering Chart, follow the example below. In this example, Circuit is a remote-controlled, 0A, pole breaker. Circuits and 5 are a remote-controlled, 0A, pole breaker. Circuit, 4 and 6 are a standard, 50A, pole breaker. of Poles Amps Rating Remote-Control Circuit Breakers Interrupt Rating (AIC) & Catalog Volts AC (50/60 Hz) Y/77 Catalog RCB05 RCB00 RCB00 RCB05 RCB00 RCB00 Standard Circuit Breakers B05 B00 B05 B00 B05 B040 B050 B060 B070 B080 B090 B00 B05 B00 B05 B00 B05 B040 B050 B060 B070 B080 B090 B00 B05 B00 B05 B00 B05 B040 B050 B060 B070 B080 B090 B00 Terminal & Branch Type Term. Type Box Box Wire Type AWG Wire # Range Main Lugs R/S Breaker Circuit Circuit Breaker R/S R 0 50 S R Amp Rating 5 Interrupt Rating (AIC) 40V AC 480Y/77V AC Main Breakers Catalog L000 L0 Draw diagonal line across number of boxes that correspond to the number of poles Amperes of Poles ,000 5,000 5,000 5,000 M00 M5 M450 M4 R = Remote-control circuit breakers S = Standard circuit breakers /8/005 Page 6 of 6 TRIATEK Lighting 05 Cobb Place Blvd. Suite 00 Kennesaw, GA