speed hydraulic motors. Permission granted to reproduce for educational use only. Contrast the operation of fixed- and variable-

Transcription

1 Chapter 9 Actuators Workhorses of the System 1

2 Objectives Describe the construction and operation of basic hydraulic cylinders, limited-rotation actuators, and motors. Compare the design and operation of various types of hydraulic cylinders. Select appropriate cylinder design options available for mounting hydraulic cylinders and reducing hydraulic shock. Compare the design and operation of various types of hydraulic motors. Goodheart-Willcox Co., Inc. 3 Objectives Contrast the operation of fixed- and variable- speed hydraulic motors. Describe the construction and operation of a basic hydrostatic transmission. Size hydraulic cylinders and motors to correctly meet system force and speed requirements. Interpret manufacturer specifications for hydraulic cylinders. Goodheart-Willcox Co., Inc. 4 2

3 Hydraulic Cylinders Actuators are the components used in a hydraulic system to provide power to a required work location Cylinders are the hydraulic system components that convert fluid pressure and flow into linear mechanical force and movement Goodheart-Willcox Co., Inc. 5 Hydraulic Cylinders A basic cylinder consists of: Piston Piston rod Barrel Goodheart-Willcox Co., Inc. 6 3

4 Hydraulic Cylinders Parts of a typical cylinder Goodheart-Willcox Co., Inc. 7 Hydraulic Cylinders The piston forms sealed, variable-volume chambers in the cylinder System fluid forced into the chambers drives the piston and rod assembly Linear movement is produced Goodheart-Willcox Co., Inc. 8 4

5 Hydraulic Cylinders Seals prevent leakage between: Piston and cylinder barrel Piston rod and head Barrel and its endpieces Wiper seal, or scraper, prevents dirt and water from entering the cylinder during rod retraction Goodheart-Willcox Co., Inc. 9 Hydraulic Cylinders Various seals are used in a cylinder Goodheart-Willcox Co., Inc. 10 5

6 Hydraulic Cylinders Rod wipers prevent contamination ti from entering on rod retraction IMI Norgren, Inc. Goodheart-Willcox Co., Inc. 11 Hydraulic Cylinders Cylinders are typically classified by operating principle i or by construction ti type Single-acting or double-acting Tie rod, mill, threaded end, or one piece Goodheart-Willcox Co., Inc. 12 6

7 Hydraulic Cylinders Single- and double-acting cylinders Single-acting Double-acting Goodheart-Willcox Co., Inc. 13 Hydraulic Cylinders Single-acting cylinders exert force either on extension or retraction ti They require an outside force to complete the second motion Goodheart-Willcox Co., Inc. 14 7

8 Hydraulic Cylinders Double-acting cylinders generate force during both extension and retraction ti Directional control valve alternately directs fluid to opposite sides of the piston Force output varies between extension and retraction Goodheart-Willcox Co., Inc. 15 Hydraulic Cylinders Effective piston area is reduced on retraction due to the rod cross section Goodheart-Willcox Co., Inc. 16 8

9 Hydraulic Cylinders Volume is reduced on retraction Goodheart-Willcox Co., Inc. 17 Hydraulic Cylinders External tie rod bolts are used to secure the ends on the tie-rod cylinder design Commonly found on heavy industrial machines External tie rods increase chance of damage and promote accumulation of dirt Goodheart-Willcox Co., Inc. 18 9

10 Hydraulic Cylinders Tie-rod cylinder Goodheart-Willcox Co., Inc. 19 Hydraulic Cylinders Mill cylinders Yates Industries, Inc. Goodheart-Willcox Co., Inc

11 Hydraulic Cylinders Threaded-end cylinder Bailey International Corporation Goodheart-Willcox Co., Inc. 21 Hydraulic Cylinders One-piece cylinder has the cylinder barrel welded d to the ends Produces a compact actuator Cost effective to manufacture Cannot be serviced (throwaway) Goodheart-Willcox Co., Inc

12 Hydraulic Cylinders Hydraulic ram is commonly used in handtdjacks operated Rod is basically the same diameter as the inside of the cylinder barrel Large-diameter rod is more rigid under load, but cylinder can generate force in only one direction Goodheart-Willcox Co., Inc. 23 Hydraulic Cylinders Typical hand-operated jack Goodheart-Willcox Co., Inc

13 Hydraulic Cylinders Telescoping cylinders are available for applications requiring i long extension distances Rod is made up of several tubes of varying size nested inside of the barrel Each tube extends, producing a rod longer than the cylinder barrel Typical example is the actuator that raises the box on a dump truck Goodheart-Willcox Co., Inc. 25 Hydraulic Cylinders Telescoping cylinders Star Hydraulics, Inc. Goodheart-Willcox Co., Inc

14 Hydraulic Cylinders Cylinders often use hydraulic cushions Provide a controlled approach to the end of the stroke Reduces the shock of the impact as the piston contacts the cylinder head Goodheart-Willcox Co., Inc. 27 Hydraulic Cylinders Cylinder cushioning device Goodheart-Willcox Co., Inc

15 Hydraulic Cylinders A variety of mounting configurations are used to attach the cylinder body and rod end to machinery Fixed centerline Fixed noncenterline Pivoting centerline Expected cylinder loading is the major factor in the selection of the mounting style Goodheart-Willcox Co., Inc. 29 Hydraulic Cylinders Head-end flange mount Goodheart-Willcox Co., Inc

16 Hydraulic Cylinders Fixed-noncenterline mount Goodheart-Willcox Co., Inc. 31 Hydraulic Cylinders Pivoting-centerline, clevis mount Goodheart-Willcox Co., Inc

17 Hydraulic Cylinders Pivoting-centerline, trunnion mount Goodheart-Willcox Co., Inc. 33 Hydraulic Cylinders The force generated by a cylinder is calculated by multiplying l i the effective area of the piston by the system pressure Goodheart-Willcox Co., Inc

18 Hydraulic Cylinders Effective cylinder piston area Goodheart-Willcox Co., Inc. 35 Hydraulic Cylinders Force generated during the extension of a double-acting cylinder with a single-endedended rod is calculated as: Ef = Sp Pa where: Ef = extension force Sp = system pressure Pa = piston area (Calculations require consistent units of measure in these formulas) Goodheart-Willcox Co., Inc

19 Hydraulic Cylinders Force generated during the retraction of a double-acting cylinder with a single-ended ddrod is calculated as: Rf = Sp (Pa Ra) where: Rf = retraction force Sp = system pressure Pa = piston area Ra = rod area Goodheart-Willcox Co., Inc. 37 Hydraulic Cylinders Speed at which the cylinder extends or retracts is determined dby: Physical volume per inch of cylinder piston travel Amount of fluid entering the cylinder Effective area of the piston is used to calculate the volume of the cylinder per inch of piston travel Goodheart-Willcox Co., Inc

20 Hydraulic Cylinders Extension speed of a double-acting cylinder with a single-ended ddrod dis calculated ltdas: Es = Fr (Cg Pa) where: Es = extension speed Fr = flow delivery rate Cg = cubic inches in one gallon Pa = piston area Goodheart-Willcox Co., Inc. 39 Hydraulic Cylinders Calculate retraction speed of a double-acting cylinder with single-ended ddrod as: Rs = Fr [Cg (Pa Ra)] where: Rs = retraction speed Fr = flow delivery rate Cg = cubic inches in one gallon Pa = piston area Ra = rod area Goodheart-Willcox Co., Inc

21 Hydraulic Cylinders Flow rate to produce a desired extension or retraction ti speed dis calculated ltdas: Fr = (Ea Cs) Cg where: Fr = system flow rate Ea = effective piston area Cs = cylinder speed Cg = cubic inches in one gallon Goodheart-Willcox Co., Inc. 41 Hydraulic Cylinders Hydraulic cylinder manufacturers provide detailed d specifications concerning: Construction Physical size Load capacity Goodheart-Willcox Co., Inc

22 Hydraulic Cylinders This information includes basic factors such as: Bore Stroke Pressure rating Other details, such as service rating, rod end configurations, and dimensions Goodheart-Willcox Co., Inc. 43 Hydraulic Cylinders Typical manufacturer s catalog page Bailey International Corporation Goodheart-Willcox Co., Inc

23 Limited-Rotation Hydraulic Actuators Limited-rotation devices are actuators with an output tshaft hftthtt that typically applies torque through approximately 360 of rotation Models are available that are limited to less than one revolution, while others may produce several revolutions Goodheart-Willcox Co., Inc. 45 Limited-Rotation Hydraulic Actuators Most common designs of limited-rotation actuators t are: Rack-and-pinion Vane Helical piston and rod Goodheart-Willcox Co., Inc

24 Limited-Rotation Hydraulic Actuators Rack-and-pinion limited rotation actuator IMI Norgren, Inc. Goodheart-Willcox Co., Inc. 47 Limited-Rotation Hydraulic Actuators Vane limited-rotation actuator Goodheart-Willcox Co., Inc

25 Limited-Rotation Hydraulic Actuators Helical piston and rod limited-rotation actuator Goodheart-Willcox Co., Inc. 49 Limited-Rotation Hydraulic Actuators Limited-rotation actuators are used to perform a number of ffunctions in a variety it of fid industrial til situations Indexing devices on machine tools Clamping of workpieces Operation of large valves Goodheart-Willcox Co., Inc

26 Limited-Rotation Hydraulic Actuators Limited-rotation actuators are used in this robotic arm IMI Norgren, Inc. Goodheart-Willcox Co., Inc. 51 Hydraulic Motors Hydraulic motors are called rotary actuators They convert fluid pressure and flow into torque and rotational movement Goodheart-Willcox Co., Inc

27 Hydraulic Motors Typical hydraulic motor application Goodheart-Willcox Co., Inc. 53 Hydraulic Motors All basic hydraulic motors consist of three component groups: Housing Rotating internal parts Power output shaft Goodheart-Willcox Co., Inc

28 Hydraulic Motors Parts of a typical hydraulic motor Goodheart-Willcox Co., Inc. 55 Hydraulic Motors System fluid enters the housing and applies pressure to the rotating ti internal parts This, in turn, moves the power output shaft and applies torque to rotate a load Goodheart-Willcox Co., Inc

29 Hydraulic Motors Primary parts that produce the rotating motion in most hydraulic motors are either: Gears Vanes Pistons Goodheart-Willcox Co., Inc. 57 Hydraulic Motors Four requirements of a motor Goodheart-Willcox Co., Inc

30 Hydraulic Motors Displacement of a hydraulic motor indicates the volume of fluid needed d to turn the output t shaft one revolution Fixed displacement Variable displacement Goodheart-Willcox Co., Inc. 59 Hydraulic Motors In a fixed-displacement motor: Internal geometry cannot be changed Same volume needed per output shaft revolution Goodheart-Willcox Co., Inc

31 Hydraulic Motors In a variable-displacement motor: Internal geometry can be changed Displacement per shaft revolution can be adjusted Motor can operate at variable speeds with a constant input flow Goodheart-Willcox Co., Inc. 61 Hydraulic Motors Hydraulic motors may be classified by the type of fload applied dto the bearings of fthe output t shaft Unbalanced indicates the output shaft is loaded from one side, side loading the shaft bearings Balanced indicates the bearing load is balanced by use of two inlet ports arranged opposite of each other and two outlet ports similarly arranged Goodheart-Willcox Co., Inc

32 Hydraulic Motors The external gear hydraulic motor is the most common and simplest of fthe basic motor types Fixed displacement Unbalanced load on the bearings Goodheart-Willcox Co., Inc. 63 Hydraulic Motors The most common internal gear motor has a gerotor design Courtesy of Eaton Fluid Power Training Goodheart-Willcox Co., Inc

33 Hydraulic Motors The specially shaped gear teeth of the gerotor form variable-volume l chambers that tallow system fluid flow and pressure to turn the motor output shaft Gerotor motors are fixed-displacement units operating with an unbalanced bearing load Goodheart-Willcox Co., Inc. 65 Hydraulic Motors An orbiting gerotor motor is a variation of the basic gerotor design Uses a fixed outer gerotor gear with internal teeth and an inner gear with external teeth Center point of the inner gear orbits around the center point of the fixed gear with internal teeth Motor operates at a slower speed, but has a higher torque output Goodheart-Willcox Co., Inc

34 Hydraulic Motors Orbiting gerotor motor Courtesy of Eaton Fluid Power Training Goodheart-Willcox Co., Inc. 67 Hydraulic Motors Basic vane motor has a slotted rotor located off center in a circular chamber and fitted with movable vanes Space between the vanes creates a number of variable-sized chambers Forcing fluid into the small-size chambers causes the volume of the chambers to increase, turning the motor shaft Basic vane motor is fixed displacement with an unbalanced bearing load Goodheart-Willcox Co., Inc

35 Hydraulic Motors Basic vane motor Goodheart-Willcox Co., Inc. 69 Hydraulic Motors Balanced vane motors evenly distribute the load on the bearings Achieved by operating the rotor and vanes in a slightly oblong chamber Allows two inlet ports and two outlets ports to be used in the motor Placing ports opposite each other balances bearing loading Goodheart-Willcox Co., Inc

36 Hydraulic Motors A basic, balanced vane motor Goodheart-Willcox Co., Inc. 71 Hydraulic Motors Vane motors are available as either fixed or variable ibl displacement The variable-displacement feature allows an operator to change the speed of a motor without changing the system flow rate Goodheart-Willcox Co., Inc

37 Hydraulic Motors In variable-displacement designs, the chamber in which hthe rotor and vanes operate is contained in a moveable ring When the center point of the rotor and ring are concentric, the displacement is zero Moving the ring so the center points are not concentric increases the motor displacement and changes motor speed Goodheart-Willcox Co., Inc. 73 Hydraulic Motors Piston motors are available having either fixed or variable ibl displacements In variable-displacement designs, the length of the piston stroke is changed to vary the volume of fluid needed to rotate the motor one revolution Goodheart-Willcox Co., Inc

38 Hydraulic Motors Two basic classifications of piston motors are axial ilpiston it and radial dilpiston it An axial piston motor has pistons with centerlines parallel to the axis of the output shaft A radial piston motor has pistons with centerlines perpendicular to the axis of the output shaft Goodheart-Willcox Co., Inc. 75 Hydraulic Motors Axial piston motor The Oilgear Company Goodheart-Willcox Co., Inc

39 Hydraulic Motors Axial piston motors are available in two configurations: Inline Bent axis Goodheart-Willcox Co., Inc. 77 Hydraulic Motors In an inline piston motor: Centerline of the barrel is concentric with the centerline of the power output shaft A swash plate transmits force from the pistons to the shaft Goodheart-Willcox Co., Inc

40 Hydraulic Motors Inline piston motor The Oilgear Company Goodheart-Willcox Co., Inc. 79 Hydraulic Motors In a bent-axis piston motor: Centerline of the barrel is at an angle to the centerline of the output shaft A universal joint and other fittings are used to transmit force between the barrel and the output shaft Goodheart-Willcox Co., Inc

41 Hydraulic Motors Bent-axis piston motor Courtesy of Eaton Fluid Power Training Goodheart-Willcox Co., Inc. 81 Hydraulic Motors A number of alternate motor designs are used in specialized dhydraulic applications Screw motor designs for quiet, continuous operation Special piston-motor designs allowing the direct mounting and drive of wheels for off-road, heavytransport vehicles Goodheart-Willcox Co., Inc

42 Hydraulic Motors Hydraulic motors may be incorporated into circuits it using series or parallel lconnections Series circuits: total system pressure is determined by adding the loads placed on each unit Parallel circuits: each motor receives full system pressure; loads must be matched or equal flow supplied to each motor if constant speed is desired from each unit Goodheart-Willcox Co., Inc. 83 Motors in series Hydraulic Motors Goodheart-Willcox Co., Inc

43 Hydraulic Motors Motors in parallel Goodheart-Willcox Co., Inc. 85 Hydraulic Motors Motors in parallel with flow control Goodheart-Willcox Co., Inc

44 Hydraulic Motors Braking circuits are used to slow hydraulic motors to a stop Inertia of a heavy rotating load can continue to turn the motor shaft Braking occurs when fluid discharged from the motor outlet port is forced to pass through an adjustable pressure control valve before returning to the reservoir Goodheart-Willcox Co., Inc. 87 Braking circuit Hydraulic Motors Goodheart-Willcox Co., Inc

45 Hydraulic Motors An open-loop hydraulic motor system uses a layout ttypical of a basic hydraulic system Pump moves fluid from a reservoir, through a directional control valve, to the motor Fluid is then returned from the motor to the reservoir through the same control valve Goodheart-Willcox Co., Inc. 89 Hydraulic Motors Closed-loop hydraulic motor systems continuously circulate fluid between the pump and the motor without returning it to a system reservoir These systems use a replenishment circuit to replace fluid lost through leakage Goodheart-Willcox Co., Inc

46 Hydraulic Motors Replenishment circuit Goodheart-Willcox Co., Inc. 91 Hydrostatic Drives Hydrostatic drive systems consist of the basic components typically found in other hydraulic motor circuits MDMA Equipment Menomonie Goodheart-Willcox Co., Inc

47 Hydrostatic Drives Hydrostatic drives provide effective transmission i of power and allow easy adjustment and control of: Output shaft speed Torque Horsepower Direction of rotation Goodheart-Willcox Co., Inc. 93 Hydrostatic Drives When compared to conventional transmissions, hydrostatic ti drives: Have a high power output to size ratio May be stalled under full load with no internal damage Accurately maintain speed under varying load conditions Provide an almost infinite number of input/output speed ratios Goodheart-Willcox Co., Inc

48 Hydrostatic Drives Hydrostatic drives may be open or closed circuits it Open circuit has the layout of a basic hydraulic motor circuit Closed circuit has the outlet of the pump directly connected to the inlet of the motor and the outlet of the motor directly connected to the inlet of the pump Goodheart-Willcox Co., Inc. 95 Hydrostatic Drives Open circuit design Goodheart-Willcox Co., Inc

49 Hydrostatic Drives Closed circuit design Sauer-Danfoss, Ames, IA Goodheart-Willcox Co., Inc. 97 Hydrostatic Drives Four combinations of pump/motor arrangements can be used Fixed-displacement pump and motor Fixed-displacement pump and variabledisplacement motor Variable-displacement pump p and fixeddisplacement motor Variable-displacement pump and motor Goodheart-Willcox Co., Inc

50 Hydrostatic Drives Fixed-displacement pump and motor: Maximum horsepower, torque, and output shaft speed are fixed Pump and motor have fixed displacement, so these characteristics cannot be changed Goodheart-Willcox Co., Inc. 99 Hydrostatic Drives Fixed-displacement pump and variable- displacement motor: Maximum horsepower is fixed Torque and speed are variable Due to use of a relief valve, efficiency is lowered Output shaft rotation may be reversed if the pump is reversible Goodheart-Willcox Co., Inc

51 Hydrostatic Drives Variable-displacement pump and fixed- displacement motor: Torque output is fixed Horsepower and output shaft speed are variable Output shaft rotation may be reversed if pump is reversible Goodheart-Willcox Co., Inc. 101 Hydrostatic Drives Variable-displacement pump and motor: Horsepower, torque, output shaft speed are variable Output shaft direction is reversible Most versatile of the four pump/motor combinations Goodheart-Willcox Co., Inc

52 Hydrostatic Drives Hydrostatic drives are typically considered hydrostatic ti transmissions i when both the pump and motor have variable displacement This combination allows manual or automatic control of torque, speed, and power output Goodheart-Willcox Co., Inc. 103 Hydrostatic Drives Two different general techniques are used in the construction of hydrostatic transmissions Integral Nonintegral Goodheart-Willcox Co., Inc

53 Hydrostatic Drives Integral construction combines all of the transmission i parts into a single housing Nonintegral construction involves separate pump, motor, and accessories connected by hoses or tube assemblies Goodheart-Willcox Co., Inc. 105 Review Question A(n) cylinder can exert force during both ththe extension and retraction ti strokes. double-acting Goodheart-Willcox Co., Inc

54 Review Question A(n) is the system component that converts fluid pressure and dflow into linear force and movement. hydraulic cylinder Goodheart-Willcox Co., Inc. 107 Review Question List the three basic configurations used to mount cylinders to equipment. A. Fixed centerline, B. fixed non-centerline, and C. pivoting centerline. Goodheart-Willcox Co., Inc

55 Review Question The three conceptual component groups that make up any hydraulic motor are: A. Rotor, vanes, and eccentric. B. Housing, rotating internal parts, and power output shaft. C. Housing, reciprocating internal parts, and power input shaft. D. Rotating internal parts, power input shaft, and power output shaft. B. Housing, rotating internal parts, and power output shaft. Goodheart-Willcox Co., Inc. 109 Review Question To vary the displacement of a vane motor, a movable is used to change the size of the pumping chambers. cam ring Goodheart-Willcox Co., Inc

56 Review Question List the four possible pump/motor arrangements that t may be used with a hydrostatic ti system. A. Both pump and motor have fixed displacements, B. pump has a fixed displacement and the motor a variable displacement, C. pump has a variable displacement and the motor a fixed displacement, and D. both pump and motor have variable displacement. Goodheart-Willcox Co., Inc. 111 Review Question During retraction, what is the effective area of the piston of a double-acting cylinder? The cross-sectional area of the piston minus the cross-sectional area of the rod. Goodheart-Willcox Co., Inc

57 Review Question A cylinder that has externally mounted metal rods holding the ends on the barrel is called a(n) cylinder. tie-rod Goodheart-Willcox Co., Inc. 113 Glossary Barrel The component containing the cylinders of an axial piston hydraulic pump. Clevis mount A cylinder rod and cap mounting configuration involving a C-shaped casting and a mounting gpin that allows the cylinder to pivot during extension and retraction. Goodheart-Willcox Co., Inc

58 Glossary Closed circuit A hydraulic circuit design in which pump output is returned directly to the pump inlet after passing through a hydraulic motor. The design is commonly used with hydrostatic drive systems. Goodheart-Willcox Co., Inc. 115 Glossary Cushioning A design feature in fluid power cylinders that t reduces fluid flow near the end of the extension or retraction stroke to decelerate piston movement, which avoids both noise and component damage. Double-acting cylinder Cylinders that may be powered both on the extension and retraction strokes. Goodheart-Willcox Co., Inc

59 Glossary Effective piston area The area of a piston that contributes to the force generated by system pressure. For example, the effective area of a cylinder piston during retraction is the area of the piston minus the cross-sectional area of the piston rod. Goodheart-Willcox Co., Inc. 117 Glossary Fixed-centerline mount A cylinder-mounting design in which the load carried by the cylinder rod and piston is supported at the centerline of the cylinder barrel, which is fixed to a machine member. Goodheart-Willcox Co., Inc

60 Glossary Head The height of a column of water or other liquid necessary to develop a stated pressure. Hydrostatic drive A fluid power drive system using a hydraulic pump and motor to transmit the power of a prime mover to the input of a machine. Available in either openor closed-circuit designs. Goodheart-Willcox Co., Inc. 119 Glossary Limited-rotation actuator An actuator t design that tprimarily il produces rotational movement of one revolution or less. Various designs are available using a rack and pinion, vane, or helical shaft. Mill cylinder A hydraulic cylinder constructed of heavy steel for use in industries such as foundries and steel mills. Goodheart-Willcox Co., Inc

61 Glossary Open circuit A hydraulic circuit that uses the layout of a basic hydraulic motor circuit with a directional control valve to control motor direction and a reservoir to hold surplus fluid. Goodheart-Willcox Co., Inc. 121 Glossary Orbiting gerotor motor A variation of the gerotor motor that uses the internal-toothed gear of the gerotor set as a fixed gear. The external-toothed gear orbits following the internal-toothed gear. This produces higher torque/lower speed output. Goodheart-Willcox Co., Inc

62 Glossary Parallel circuit An electrical or fluid power circuit that simultaneously provides multiple paths for the current or fluid to follow as it moves through a circuit. Goodheart-Willcox Co., Inc. 123 Glossary Pivoting-centerline mount A clevis or trunnion mounting that allows the cylinder to follow an arc as it powers a machine member. The load remains concentrated on the centerline of the cylinder. Goodheart-Willcox Co., Inc

63 Glossary Replenishment circuit A circuit used with closed-loop hydraulic systems that provides makeup fluid to replace any fluid lost from leakage during system operation. Series circuit An electrical or fluid power circuit that provides only one path for the current or fluid to follow as it moves through the circuit. Goodheart-Willcox Co., Inc. 125 Glossary Single-acting cylinder A cylinder design that exerts force only on extension or retraction and depends on some outside force to complete the second movement. Goodheart-Willcox Co., Inc

64 Glossary Telescoping cylinder A linear actuator constructed of several nested tubes that can extend a distance equal to several times the actuator s retracted length. Threaded-end cylinder A linear actuator design in which the cap and head are attached to the barrel of the cylinder by threads. Goodheart-Willcox Co., Inc. 127 Glossary Tie-rod cylinder A linear actuator design in which the cap and head components are secured to the barrel of the cylinder by external tie rods that run between those components. Goodheart-Willcox Co., Inc

65 Glossary Trunnion mount A cylinder mounting method that places fittings on the sides of cylinders, allowing the cylinder to pivot as it extends and retracts to move a machine member. Goodheart-Willcox Co., Inc