Chassis Hardware Kit: B D. Right Top Bracket. Top Bracket Qty: 1. Qty: 1. Qty: 2 13/16" 9/16" 25/64" 1" Hex. OPlastic Spacers. Qty: 4 0.

Transcription

1 0.437" 5/32" ex 0.437" 5/32" ex 0.132" 1/2" 1/4"-20 Thread 0.132" 1/2" 1/4"-20 Thread 0.25" 0.25" Assembly Instructions: Manual, Dual User Workstation Chassis LOS3-B-M21-XX-XX-XX-X Parts Included: A Line of Sight Dual User Manual Chassis MVESA Mount P S #10 10 mm Monitor MVESA Mount P S #10 Zinc Washer 10 mm Monitor Zinc Washer T Cable T Cable N ¼"-20 N ¼"-20 Chassis ardware it: B Left D 5/16"-18 ⅜-16 Top Bracket Serrated Flange Nut x 1" Flange ead Cap s ½" Allen, Button ead Qty: 2 Q 16 mm Monitor Clips Qty: 3 U Cable U Cable G Lid Ties Qty: 5 ½" Allen, Button ead Qty: 2 Q 16 mm Monitor Clips Qty: 3 Ties Qty: 5 CAUTION: Manual Lift models are spring loaded and require extra care until a monitor has been installed. Follow all warnings and cautions. C Right Top Bracket Stop Qty: 2 13/16" Monitor Mount & Wiring ardware it, Manual: 9/16" V L ⅜" O 25/64" 1" Plastic Spacers R OPlastic Spacers R #10-¾" 25 mm Monitor Monitor Mount & Wiring ardware it, Manual: ex 3/8"-16 Thread Phillips Pan ead s Qty: 30 Glides 0.375" Wire Loom, 1" 2' 25 mm Monitor CAUTION Wire Loom,! 1" 2' V MISE Qty: EN 1GARDE! Product is spring loaded and Ne may faites open pas with fonctionner extreme sans force des contrepoids when screw is removed. MISE pourraient EN survenir. GARDE! Foot it I J Right E Worksurface Left Foot Foot Worksurface & Monitor Bay Lid F Monitor Bay Lids Qty: 2 Optional, Sold Separately Ganging Brackets, Filler Channels, Back to Back End Panels, Power System Components, CPU olders Ne faites pas fonctionner sans des contrepoids pourraient survenir. PUS ERE TO RAISE OR LOWER TE MONITOR Caution: Spring loaded mechanism. Exercise caution when cycling up or down! Verify That You ave All The Tools Needed For The Assembly You will need the following tools: Drill/driver or Phillips screwdriver with #2 tip 5/32" Allen wrench ½" Open ended wrench 9/16" Open ended wrench Ne faites pas fonctionner sans des contrepoids pourraient survenir. 1 of 8 Line of Sight (800) los.workriteergo.com or Ne faites pas fonctionner sans des contrepoids pourraient survenir.

2 1 Remove Front and Rear Panels, Set Power Cord Aside 1.1 Remove the Front and Rear Panels from the Chassis (A) by turning the Panel Locks a quarter turn towards the center of the panel (inward), then pivot the panels Panel Lock forward to remove. Rear Panels A If you have Locking Panels, unlock using the included key. 1.2 eep the protective tape around panels and on frame until assembly is complete to protect finish. Front Panels Protective 1.2 tape Removable Panel Locking Panel 2 Attach Top Brackets Attach the Left Top Bracket (B) and Right Top Bracket (C) to Chassis (A) with the four 5/16"-18 Locknuts (D). Threaded studs on the brackets insert through holes in the Chassis and are held in place with the Locknuts. B D Threaded Studs C ardware at actual size D 5/16"-18 Serrated Flange Nut D Under Top Bracket 3 Attach Lid Stops to Worksurface Note: Build Assembly in a large, clean area on carpeting or moving blankets to prevent damaging Worksurface and Lid. 3.1 Place Worksurface (E) and Monitor Bay Lid (F) upside down on floor. Slide Monitor Bay Lid (F) into cutout in Worksurface (E). E G F G F 3.2 Attach both Lid Stops (G) with eight #10-¾" Phillips Pan ead s (). ardware at actual size #10-¾" Phillips Pan ead s 2 of 8 Line of Sight (800) los.workriteergo.com

3 4 Flip Chassis Upside Down Onto Worksurface 4.1 Place the Worksurface and Monitor Bay Lid upside down on the floor and slide the Monitor Bay Lid into the cutout in the Worksurface. Monitor Bay inge 4.2 Flip the Chassis assembly upside-down onto the bottom of Worksurface Use at least two people to flip over and position the Chassis. 4.3 Align Chassis assembly so holes in Top Brackets line up with pre-drilled holes in Worksurface and holes in Monitor Bay inges line up with predrilled holes in Monitor Bay Lid. 4.1 Monitor Bay Lid Worksurface 5 Mount Chassis Assembly to Worksurface & Monitor Bay Lid 5.1 With Chassis Assembly correctly positioned on Worksurface, attach Chassis Assembly to Worksurface with eight #10-¾" Phillips ead s (), four screws per Top Bracket (B & C). 5.2 Note: Chassis models over 48" have a Center Support which requires two #10-¾" Phillips ead s () into the Center Support. 5.3 Attach Monitor Bay Lid to both Monitor Lid inges with two #10- ¾" Phillips ead s () per hinge at the forward location. You will finish installing the hinges in Step 10 when workcenter is right side up and you can more easily access the two other hinge screw holes. Note: Monitor Bay Lid will have approximately.2" of clearance around the cutout in the Worksurface when properly installed. B ardware at actual size #10-¾" Phillips Pan ead s Two screws per hinge at forward locations (4 hinges) C Center Support Lid Stay Attach to Worksurface Attach to Monitor Bay Lids 5.4 Attach the Lid Stay to the Monitor Bay Lid with two #10-¾" Phillips Pan ead s (). 3 of 8 Line of Sight (800) los.workriteergo.com

4 6 Attach Feet and Glides Attach Left Foot (I) and Right Foot (J) from the inside, bottom of Chassis using four ⅜-16 1¼" Flat ead Socket Cap s (). Note that the Left Foot will be on the right and vice versa with the Chassis is upside down. L J I in the four Glides (L) into the feet approximately half way. You will level the Workcenter once it has been flipped right side up. 6.1 ardware at actual size ⅜-16 x 1" Flange ead Cap 7 Flip Workcenter Flip over the assembled Workcenter with at least two people. ng loaded and may open with extreme force when screw is removed. ssort et peut s ouvrir avec un force extrème lorsque cette vis est enterèe. està cargado con resortes y puede abrise con extrema fuerza cuando 8 Remove Safety ng loaded and may open with extreme force when screw is removed. ssort et peut s ouvrir avec un force extrème lorsque cette vis est enterèe. Remove the Safety from the top of the Monitor Lift with a #2 està cargado con resortes y puede abrise con extrema fuerza cuando Phillips screwdriver. Remove, but retain the screw in case you need to ship the Workcenter without a monitor in the future. CAUTION: The Monitor Lift is spring loaded! Removing the Safety ATENCIÓN! unlocks the mechanism allowing the Monitor Lift to raise. ON! unterbalance nd/or damage ARDE! ontrepoids des dommages Ne faites pas fonctionner sans des contrepoids pourraient survenir. ION! uados en su lugar. Top of Monitor Lift 4 of 8 Under Workcenter Line of Sight (800) los.workriteergo.com

5 9 Raise Monitor Lift 9.1 Lift both Lids fully open. 9.2 Press down on "PUS ERE" label on top of the Manual Lifts. Spring loaded mechanism! Take care during the first time Monitor Arm is activated. With no monitors in the Monitor Mount, the mechanism is FULLY LOADED and will spring up with maximum force. 9.1 Monitor Bay Lid andle Monitor Lift PUS ERE TO RAISE OR LOWER TE MONITOR Caution: Spring loaded mechanism. Exercise caution when cycling up or down! 10 Complete Monitor Bay Lid Attachment Finish attaching Monitor Bay Lid to both Monitor Lid inges with two remaining #10-¾" Phillips ead s () per hinge. Previously installed in Step 5.2 Monitor Lift ardware at actual size #10-¾" Phillips Pan ead s 9.2 Note: Monitor Bay Lid will have approximately.2" of clearance around the cutout in the Worksurface when properly installed. You may need to loosen the inge s to adjust and re-tighten. 5 of 8 Line of Sight (800) los.workriteergo.com

6 11 Mount VESA Compatible Monitor to Monitor Lift Note: You will need to mount the monitors in order to determine the correct installation height and counterbalance weight. Remove the monitor from the factory mount if necessary, and retain the screws that came with the monitor for Step Attach VESA Plate (M) to the back of your VESA compatible Monitor with Spacers (O), s (P, Q,R) and Washers (S) or use the screws that came with your monitor. Always use the shortest screws possible, so you do not damage your monitor Attach the VESA Bracket Monitor Assembly as high as possible on the Monitor Lift using two ¼"-20 ½" Button ead s (N) and the 5/32" Allen wrench. 5/32" Allen wrench 11.3 Repeat for second monitor. ardware at actual size N N ¼"-20 ½" Button ead 11.2 VESA compatible monitor 11.2 P Q or R M P 10 mm Monitor s Q 16 mm Monitor s Attach VESA Bracket Monitor Assembly R 25 mm Monitor s Important Note: It is strongly recommended to use the mounting screws provided by the monitor manufacturer if possible. If longer screws are required, use the shortest screws possible to avoid damage to the monitor. 12 Set Counterbalance Weight Note: You will need to establish an equilibrium between the weight of the monitor with Ballast Plates and the lifting force of the Monitor Lift. Ballast Plates are best reached from under the worksurface. Remove the Wing Nut. With the monitor installed, remove ballast plates until the monitor fully raises when the Monitor Lift is engaged. Replace the Wing Nut to secure in place. Repeat for second monitor. Wing Nut Ballast Plate Under Worksurface 6 of 8 Line of Sight (800) los.workriteergo.com

7 13 Install Power Distribution Options for Your Configuration With the Workcenter built, you will now need to add your power options for your specific configuration. Follow the instructions that came with the Power System Options to complete your configuration. If you did not purchase the Power Track or Power Bar, skip to Step Install Optional Accessories for Your Configuration With the monitors and power components installed, you will now need to add your optional accessories like Worksurface Grommets, Remote Controls and CPU olders. Follow the instructions with the Optional Accessories to complete this step. 15 Install Technology for Your Configuration With all Line of Sight components installed, you will now need to install all the technology components to complete your system. Install all computers, peripherals like keyboards and mice, and network cabling to complete your installation according to the manufacturers specifications and your specific application. 16 Manage Cabling T With monitors and technology installed, you'll want to start considering all the cabling requirements. Note: It is critical that no wires interfere with the travel of the Monitor Lift. Use Cable Clips (T) for single wires (mouse & keyboard) and Cable Ties (U) for multiple wires to fasten all cabling securely out of the way of all moving Monitor Lift components. Use the Wire Loom (V) to manage all user cables routing from the keyboard tray to the CPU. This may include keyboard, mouse, monitor and data cables. U Monitor Lift eyboard tray cable access V To CPU 17 Remove Protective Tape & Replace Front and Rear Panels 17.1 Remove the protective tape on the Panels and Chassis 17.2 Remove 17.2 Reattach your front and rear panels. You now have a complete Workcenter. Finish building all Workcenters before proceeding to final room assembly Remove Front & Rear Panels 7 of 8 Chassis Line of Sight (800) los.workriteergo.com

8 18 Assemble Final Room Configuration & Connect to Power Source With all individual Workcenter Built and electrical installed, arrange Workcenters according to your final room configuration. You will need at least two people to move a Workcenter. Adjust the Glides (L) on the bottom of the Feet to assure each Workcenter is level and stable in its final location. Note: It is critical that you follow all warnings and cautions when you get to final assembly. Consult the instructions that came with your electrical components and follow all cautions and warnings carefully! Configurations with shared power must conform to code and include use of Ganging Brackets for Side to Side configurations or Back to Back Filler Plates for Back to Back configurations. Final assembly will include testing of electrical components and functioning of all Monitor Lifts. Cleaning Instructions Laminate Worksurfaces: For everyday cleaning, wipe the surface with a damp cloth or sponge. Use a spray cleaning agent sparingly if necessary (suggested spray cleaning agents are indicated below). Do not pour water directly onto the worksurface. Wipe completely dry with a soft rag using a straight line motion. Worksurfaces may need occasional dusting. To keep the surface in ideal condition, use a non-oily furniture spray. Difficult stains such as coffee can be removed using a mild cleaning detergent and a soft bristled (non-metallic) brush. Do not scrub surfaces with too much force, otherwise the surface could lose its finish. Stubborn stains that resist any of the above cleaning methods may require the use of undiluted household bleach. Apply a very small amount of bleach (approximately ¼-capful) to the stain and let stand no longer than two minutes. Rinse thoroughly with warm water and wipe dry. WARNING: Prolonged exposure of the laminate surface with bleach will cause discoloration. Ensure to always rinse laminate surfaces after cleaning. Even a small amount of cleaning residue can result in permanent discolorations. Recommended Laminate Worksurface cleaning agents: Non-abrasive spray cleaning agents: Dawn, Fantastik, Windex, Lysol Furniture spray: Pledge Stain removers: Lestoil, Clorox Painted steel parts: Clean surfaces regularly with damp cloth If necessary, use a spray cleaning agent (e.g. Fantastik) sparingly. Wipe completely dry with a soft rag using a straight line motion. Lightly brush both vertical and horizontal surfaces to prevent dust build-up Polished chrome feet: The feet can be polished when they become dull with Aluminum polish (e.g. Flitz or Mothers Mag Polish) with special attention to keep polish from painted surfaces. Follow manufacturers instructions for best results. 8 of 8 Line of Sight (800) los.workriteergo.com # Rev A