CL6NX +Cutter (KITTING MANUAL)

Size: px

Start display at page:

Download "CL6NX +Cutter (KITTING MANUAL)"

Bernadette Marshall
5 years ago
Views:

1 原本 BARCODE PRINTER CL6NX +Cutter (KITTING MANUAL) WWCL9500: Cutter kit 5/Jan/205 Production Engineer Dept SATO TECHNOLOGY CO.,LTD APPROVED CHECKED INCHARGE 間下白濱横山 PE-E70Z02 E70Z02

2 Revision History Model : CUTTER KIT Kitting (CL6NX) Rev Date E.O No. Description Revised Page(s) APR CHK PIC - 5/Jan/205 - 初版発行

3 CUTTER UNIT RELAY PCB + CUTTER-CABLE SCREW (M3x6mm): 2pcs SCREW (M3x8mm): 4pcs FRONT PANEL (CT) SCREW (M4x0mm)-Black: 2pcs

<Preparation tool and Caution> Phillips screwdriver +No.

Remove () screw, and take-out (2) and (3). 3.

Relay-PCB Slide Relay-PCB Pull Option-cable Disuse

(2) PAN SCREW SW+WL (MD340428): 2pcs FRONT COVER BOTTOM

Fix (4) Relay-PCB by (6) screw (5) CUTTER CABLE 5.

into Center-frame s slot (4) RELAY-PCB Cable set position

4 <Preparation tool and Caution> Phillips screwdriver +No.2 Please turn OFF the power before assembling the cutter. <Assembly procedure>. Open the open-cover, and Open the Head 2. Remove () screw, and take-out (2) and (3). 3. Connect (0) Option-cable and (5) Cutter-cable to (4) Relay-PCB Slide Relay-PCB Pull Option-cable Disuse Cutter-cable (3) Reuse FRONT COVER BOTTOM (LH) Disuse () (2) PAN SCREW SW+WL (MD340428): 2pcs FRONT COVER BOTTOM (0) OPTION CABLE * This is Printer side item 4. Fix (4) Relay-PCB by (6) screw (5) CUTTER CABLE 5. Attach (7) Front-cover, while passing thru Cutter-cable into Center-frame s slot (4) RELAY-PCB Cable set position (6) PAN SCREW SW+WS (MD ): 2pcs Torque : 3.5~4.5 Kg cm 6. Connect (5) Cutter-cable to PCB (of Cutter-unit) Reuse (7) FROTN COVER UNDER (LH)

7. Attach (8) Cutter-unit to printer, fix it by (9) screw. Torque : 7.0~8.

While opening the Cutter-open-lever, attach (0) Front-panel (CT), and fix it by

Power (8) CUTTER UNIT () PAN SCREW SW+WL (MD340028): 2pcs (0) FRONT PANEL (CT)

0 Kg cm <Check and adjust after assembly Cutter-kit> <Preparation> () Set Label

(3) Power ON the printer (press Power key). (4) Press Soft-L.

5 7. Attach (8) Cutter-unit to printer, fix it by (9) screw. Torque : 7.0~8.0 Kg cm (9) PAN CREW SW+WL (MD ): 4pcs 8. While opening the Cutter-open-lever, attach (0) Front-panel (CT), and fix it by () screw. Power (8) CUTTER UNIT () PAN SCREW SW+WL (MD340028): 2pcs (0) FRONT PANEL (CT) Soft-L Soft-R Torque : 4.0~6.0 Kg cm <Check and adjust after assembly Cutter-kit> <Preparation> () Set Label and Ribbon to printer. (2) Close the Head. (3) Power ON the printer (press Power key). (4) Press Soft-L. (5) Press Soft-R,display the Offline. // Enter Navigation <Check contents>. Check Cutter-Open-Error () After opening the Cutter-open-lever, confirm that LCD-display is Cutter-open-Error message. (2) After checking, close and lock the Cutter-open-lever. Cutter-open-Error Open Open Cutter-open-lever

2. Adjust of Cut-position In Offline, press the [Soft-R] key Printer loads one

OK NG Soft-L Soft-R (A) Label loading direction (B) Back Enter // If NG (cutting on

<Adjust method of Offset > Navigation () Press //, change Online Offline (2) Press

Settings-menu: Printing Tools Press Enter key (4) Select Test Print, press Enter

Offset value Reduce ( ) (B); Increase ( ) (7) After setting, By press Soft-R key,

When Label-pitch is less than 00mm, Press // x3 times, press the [Soft-R] key.

6 2. Adjust of Cut-position In Offline, press the [Soft-R] key Printer loads one sheet label (blank), and cuts it. Power Confirm that cutting is on label gap. OK NG Soft-L Soft-R (A) Label loading direction (B) Back Enter // If NG (cutting on label), adjust the Offset value. <Adjust method of Offset > Navigation () Press //, change Online Offline (2) Press Enter key, display the Settings (3) Press or key several times Change Settings-menu: Printing Tools Press Enter key (4) Select Test Print, press Enter (5) Select Factory, press Enter (6) Select Offset, Set Offset value In case of (A); Offset value Reduce ( ) (B); Increase ( ) (7) After setting, By press Soft-R key, printer is issued Test-printing. When Label-pitch is less than 00mm, Press // x3 times, press the [Soft-R] key. Confirm the cutting position is OK or NG. If it was NG, please perform (6)~(7) again. Then If printing-position needs to adjust, please set it by Pitch value. Cutting position adjust Printing position adjust Test-print

(Bottom-Front) ~with Cutter model Cushion

(Bottom-Front) +CT model Remove the Cushion

7 <Packing method>. Remove Small-piece from Cushion (Bottom-Front) ~with Cutter model Cushion (Top Front -L) Cushion (Top Rear) Cushion (Top Front -R) Cushion (Bottom-Rear) () CUSHION (BOTTOM-FRONT ) Modify the Cushion (Bottom-Front) +CT model Remove the Cushion piece from Cushion (Bottom-Front) * This small piece is not use for +CT model, please throw away it.

Susunan packing item seperti gambarajah di bawah.

Q046294xx 9 CARTON SPACER Q046290xx 8 CUSHION (T-R) 7 Q046289xx

Q046288xx CUSHION (T-F- RH) 2 Q046428xx CARTON SPACER(FR) 5

SIDE 3 Q04629xx CUSHION (B-F) PRINTER FRONT SIDE Q046287xx

Cushion (T-F-LH) Cushion (T-R) Carton Spacer (tape tidak

8 Susunan packing item seperti gambarajah di bawah. Pastikan taping bawah carton case bentuk H. Q046294xx 9 CARTON SPACER Q046290xx 8 CUSHION (T-R) 7 Q046289xx CUSHION (T-F- LH) PACKING TAPE TOP : H PASTE BOTTOM : H PASTE 6 Q046288xx CUSHION (T-F- RH) 2 Q046428xx CARTON SPACER(FR) 5 Q046292xx CUSHION (B-R) PRINTER FRONT SIDE SLIT PRINTER REAR SIDE 3 Q04629xx CUSHION (B-F) PRINTER FRONT SIDE Q046287xx CARTON CASE (PRINT) Carton spacer(fr) SLIT hole Direction Cushion (T-F-LH) Cushion (T-R) Carton Spacer (tape tidak kelihatan) PRINTER front side PRINTER FRONT SIDE Parts No Parts No Cushion (B-F) MODIFIED Cushion (B-R) Cushion (T-F-RH)

CL6NX +Dispenser (KITTING MANUAL)

原本 BARCODE PRINTER CL6NX +Dispenser (KITTING MANUAL) WWCL9500: Dispenser kit WWCL95300: Dispenser kit + Rewind 5/Jan/05 Production Engineer Dept SATO TECHNOLOGY CO.,LTD APPROVED CHECKED INCHARGE 間下 05..5