WARNING. This shows the detail that could lead to death or severe injury if ignored or through misuse the product.

Size: px

Start display at page:

Download "WARNING. This shows the detail that could lead to death or severe injury if ignored or through misuse the product."

Juniper Joseph Day
5 years ago
Views:

1 OWNER S MANUAL

2 WARNING Please read this manual thoroughly for proper use and store it for later use when needed. The Company will not be responsible for any damage due to misuse of the product. This manual has been prepared to allow you to use the product correctly and safely by means of illustrations to prevent any harm by other persons or other property. Below are definitions of the symbols used. Please carefully understand the meanings before reading the instruction manual. This shows the detail that could lead to death or severe injury if ignored or through misuse the product. In case of error, such as no sound or picture, foreign objects inside, smoke or strange smells, stop using the product immediately and contact your dealer. This could cause accident, fire and electric shock. Do not operate or watch while driving. Stop the vehicle in a safe location before operation. Failure to do so may result in an accident. Do not disassemble or modify the product. It could cause accident, fire or electric shock. Keep all cords and wires from interference with driving operation. Binding with Handle, Transmission Lever or Break Paddle could cause accident or system breakdown. Keep small objects such as batteries, screws out of the reach of children.if swallowed, consult a doctor immediately. Rear seat passenger should fasten the seat belt to prevent accidents due to quick take off or urgent breaking. These could cause accident or injury. Use the correct ampere rating when replacing fuses. Failure to do so may result in fire or electric shock. Do not wipe with oil, alcohol, benzene or thinner and do not use it with hair spray or pesticides. Please wipe off any stains immediately. It may be the cause of cracks, electric shock or fire. Only used in cars with 12-volt DC negative ground. (Check with your dealer if you are unsure.) Failure could result in a fire. Before installation, disconnect the battery from negative ground to prevent injury from electric shock or other injury. This shows the detail that could lead to death or severe injury if ignored or through misuse the product. Please correctly install as described in this manual. Failure to do so may result in fire or an accident. Use the correct ampere rating when replacing fuses. Failure to do so may result in fire or electric shock. Please avoid lines between objects or edges. It may cause electric shock or fire due to short circuit. Please do not connect the power from other sources by stripping cable insulation. This may cause fire or electric shock. Do not close or block the ventilation grill. This could cause fire or crash the system Do not install in locations that obstruct the driving operation such as front view, handles, gear lever or place that could harm passengers. This may lead to accidents and injuries. Use only specified options and install firmly. Failure to do so may result in fire or an accident. Note : Due to continuous product improvement, specifications are subject to change without notice.

3 Do not install in a wet or dusty place, or area of high humidity. Failure to observe this may result in electric shock. Insert with the correct battery polarity. When inserting the batteries, be sure that proper polarity (+ and -) are as instructed. Rupture and chemical leakage from the battery may cause fire or personal injury. Specific knowledge and experience are needed for installation and wiring. Please contact your dealer. Please use only in the vehicle. Failure to do so may result in electric shock or injury. Do not place hands, fingers or foreign objects in gaps. Doing so may result in personal injuryor damage to the product. Cautions on Usage (Common) Do not use mobile phone or other wireless device close to this unit. This could cause noise or system malfunction. It is recommended to use mobile phones or wireless devices at a distance from the unit. Remote Starter and Car Security could also cause system malfunction. Do not use excessive force. This product is assembled carefully and with high precision parts. Please gently install the device to maintain original performance from the first time of use. Do use only for domestic use. This product is only available for domestic use. Unavailable for foreign use. Do not use at extreme temperatures. In cases where the temperature in the cabin is extremely high (parking below sunlight) or extremely cold (parking in winter), please wait until the temperature becomes normal level before using the device. Monitor Care Use soft fabric to clean the monitor when dirty. In case of severe dirt, use a soft cloth soaked with neutral detergent to clean the monitor. Do not place cloths soaked with water or neutral detergent on the unit. This could cause the unit to breakdown due to humidity emerging inside the unit. Since the back of the monitor is made from soft material, do not wipe or rub it with hard materials. Do not wipe or rub the surface of monitor with hard things due to it being easily scratched. Fuse replacement When you are replacing the fuse, please refer to the prescribed fuse holder amperage. If the fuse is dropped, please carefully check all the electrical connection parts to ensure they are not shorted. Moreover, please check the voltage of the vehicle to ensure whether it is normal or not. FOR SAFE USE

4 CONTENTS Warning Cautions on Use (Common)... 3 Overhead Monitor Remote Control Turning Power ON / OFF... 6 Monitor Remote Control... 6 Dome Light Operation Turning Dome Light ON / OFF... 7 Visual EQ Setting... 8 Picture Setting Display Mode Setting... 9 System Setting Rear Vision Operation DVD, ipod, CD/MP3/WMA/ACC and Other Operation Introduction Accessories Installation of Bracket Installation of Silicone spacer Monitor Installation Dome Light wire Diagram Basic Connection Diagram Example of System Upgrades Troubleshooting Remote Control Battery Replacement Specification

6 MENU MENU RTN RTN MODE MONITOR MODE SLICE SWITCH ENTER ENTER MUTE MUTE SETUP POWER SETUP POWER

9 SETTING Brightness: Adjust brightness of the screen. Setting range : MIN (-16) ~MAX (+16) (Factory setting : Flat 0) Color : Adjust color level of the screen. Setting range : MIN (-16) ~MAX (+16) (Factory setting : Flat 0) Tint : Adjust tint of the screen. Setting range : MIN (-16) ~MAX (+16) (Factory setting : Flat 0) Contrast : Adjust contrast of the screen. Setting range : MIN (-16) ~MAX (+16) (Factory setting : Flat 0) Shapness : Adjust sharpness of the screen.. Setting range : MIN (-16) ~MAX (+16) (Factory setting : Flat 0) Display Mode Setting Display mode can be adjusted to Wide, Cinema, Zoom, and Normal modes. 1. Press SETUP to finish adjustment. Setting menu will show on screen. 2. Press to select "Display Mode" and then press Enter. Setting Setting Picture Setting Picture Screen Setting Mode Display System Mode Setting 1 System System Setting Setting 1 2 System All Reset Setting 2 All Reset Return wide Wide 3. Press for change Display Mode. SETTING Return : Return to the previous screen. Picture Setting Reset : Reset Picture Setting to default value. Run : Run to reset. Return : Return to the previous screen. Wide : Normal image are extended uniformly in the horizontal direction and displayed over the entire screen. Note The Picture Setting will not be reset while exiting setting screen without pressing ENTER. Cinema : Normal images are expanded in the horizontal and vertical directions. The top and bottom of the image are cut off. This mode is suited for 16:9 cinema size.

12 MENU REMOTE CONTROL OPERATION Remote Control Operation Rear Vision Operation Note When you are working with rear vision, please switch to [Monitor] position for slide switch. SlLICE SWITCH Switch the Monitor AV (Change to the monitor side) BACK MODE MONITOR SlLICE SWITCH ENTER POWER SETUP Rear vision power ON/OFF Call to screen setting and finishing. ENTER Select items for all settings. MUTE SETUP SETUP ENTER Enter in the selected item at every settings. Power POWER Lighting a white LED room lamp. The dome light switch will activate when using [DOOR] mode only.

13 REMOTE CONTROL OPERATION Remote Control Operation DVD, ipod, CD/MP3/WMA/AAC, and Other Operations. SlLICE SWITCH Switch the Monitor AV (Switch to AV side) BACK BACK MENU ENTER MODE MONITOR MENU MODE SlLICE SWITCH MODE MENU BACK Switch the AV mode of Alpine Navigation System Call to DVD disk menu Return to top of menu on DVD chapter selection. (Can not be used with some discs) Previous chapter / Cueing track Long press : Rewind REMOTE CONTROL OPERATION ENTER MUTE SETUP Pause / Replay Auto memory when you press and hold Power MUTE Next chapter / track Long press : Fast forward ENTER Enter the selected item, such as DVD Chapter Select item, such as DVD Chapter MUTE Mute sound AV mode of Alpine Navigation

14 MENU ENTER MUTE INSTALLATION & CONNECTION Installation & connection ACCESSORIES Introduction 10.2 Inch WVGA LCD Monitor Remote Control RUE-3200E BACK MODE Please read this manual on pages 2-3 thoroughly for proper installation and connection. The company is not responsible for any trouble due to ignore the instruction(s) in this manual. Please complete the installation work while noting the following: SETUP Power MONITOR Work that requires a long time. Please take the time to work in places where it is bright The installation varies depending on the model, grade, age, type of the car. Please obtain information about installation from the sales dealer. The memory data of the vehicle will be erased when you take off the negative terminal of the battery. Please confirm with the vehicle information, and install it. DIN cable (5m) Dome Light cord (3m) Cushion (DIN cable for joint part ) Cushion (Dome light cord for joint part) In some models of the car (such as foreign cars), trouble(s) of the electric equipment system may be caused when you disconnecting the negative terminal of the battery, please contact the dealer. Make connections with the appropriate length. After checking the location to the installation of the monitor. Please install with caution while checking this document or the label on the code. PIN connection code (1m) Double-sided tape Please mount it using the manual of the product to be combined. If you have any questions, please contact retailers information center. Screw (M4 16) Rubber cap Battery: CR2025 (for remote control) Manual OWNER S MANUAL TMX-R3200SE Silicon spacer

15 INSTALLATION & CONNECTION Installation of Bracket Caution The installation requires expertise and experience. Please contact your dealer. Installation of Silicone Spacer Please complete the installation work while noting the following to the installation instructions of our rear vision mounting kit. Please attached double-stick tape (8pcs) on the edge of the rear side of monitor, then attached the silicone spacer later. Caution Do not use electric scre driver It is difficult to control the torque of electric screw driver. It will not only cause damage to screw holes but the vehicles damages also. Double-sided tape (8pcs) Installation of Mounting Bracket Removing the dome light for installation. Utilize the screw hole to the dome light to attach the bracket For vehicle that the dome light is attached with a clip, please find a seperate speed nut. Monitor (rear side) INSTALLATION & CONNECTION Monitor Caution It might not be possible to tighten the screw for vehicle with a gap between the interior roof panel and the dome light panel that secure the dome light. In such case, please use additional spacer to tighten the screw firmly. Spacer Dome light panel Caution Silicone spacer For prevent the scratch when install the silicone spacer, please proceed on spread colth. Interior roof panel Screw Mounting bracket Caution Please firmly tighten the screw. The monitor could fail down if it s not sufficiently tightenly Be careful with the screw size. The monitor could fail down if you use the screw that is smaller than the screw hole. Caution Be careful with the screw length. Using the screw that is longer than the space between the hole and roof top could damage the vehicle.

18 INSTALLATION & CONNECTION Basic Connection Diagram brown DIN cable Align and and connect the cable. It is the TMX-R3200SE dedicated connector. Please never be connected to other products. ACC Power supply cord (red) Connect to accessory power cord of vehicle The hybrid system installed on a vehicle and idling stop function-equipped vehicle, please remove the power from the ACC stable voltage power supply for audio. Ground (black) Connect this cord to the vehicle bode. Firmly fix it to the metal part. REMOCON OUT (brown) Remote Control Signal output. This is a remote control output cord. Connect to the input of Alpine Product Remote AUX-IN 1 (yellow) Teminal for input video signal from media player.to suit the mark. REMOCON IN (brown) ACC Power supply cord red Teminal for input video signal from media player.to suit the mark. Fuse (7.5A) Caution To prevent noise caused by vibration while driving, wrap connector with cushion (for DIN cable connectors) Ground black REMOCON OUT brown AUX-IN 1 yellow Cushion Remove a peeling paper from the cushion, and warp the connectors.

WARNING WARNING WARNING CAUTION

WARNING WARNING WARNING CAUTION English Quick start guide Symbol Identification This manual uses symbols and icons to indicate safety precautions and concerns during the installation procedure. Be sure to carefully read and understand