6. Easy for maintenance & drivers replacement. Detachable in 1 minute. Part No. Power Luminous Input Voltage PF CRI Diffuser Certificate

Size: px

Start display at page:

Download "6. Easy for maintenance & drivers replacement. Detachable in 1 minute. Part No. Power Luminous Input Voltage PF CRI Diffuser Certificate"

Myrtle Scott
6 years ago
Views:

Features 1.70% energy saving compared with fluorescent lamps. 2. Super brightness SMD2835 LEDs with LM80 report. 3.Soft and uniform light.no glare & no flickering Wide beam angle@ 160 4.

2 Features 1.70% energy saving compared with fluorescent lamps. 2. Super brightness SMD2835 LEDs with LM80 report. 3.Soft and uniform light.no glare & no flickering Wide beam Premium & optical PC cover. Flame retardant rating V0. 5. Excellent heat dissipation, temperature of P-N junction 25 ambient temperature. 6. Easy for maintenance & drivers replacement. Detachable in 1 minute. Lighting Parameters Electrical / Optical Characteristics at TA=30 Size Part No. Power Luminous Input Voltage PF CRI Diffuser Certificate 2FT 4FT T8-10W-60-AHC T8-18W-120-AHC 10W 18W 1000LM 1800LM AC V PF>0.9 AC V PF>0.9 Ra>80 Frost/Clear UL&cUL(E362179) DLC listed Ra>80 Frost/Clear UL&cUL(E362179) DLC listed 5FT T8-22W-150-AHC 22W 2200LM AC V PF>0.9 Ra>80 Frost/Clear UL&cUL(E362179) Notes:Tolerance of measurement of luminous intensity±5%. Dimension Notes:All dimension units are millimeter,and all dimension tolerance is ±1mm unless otherwise noted.

3 Optical properties T8-10W-60-AHC Light Distribution Curve T8-10W-60-AHC illuminance T8-18W-120-AHC Light Distribution Curve T8-18W-120-AHC illuminance

T8-22W-150-AHC Light Distribution Curve T8-22W-150-AHC iiluminance Temperature test 100.0 temperature 10.

4 T8-22W-150-AHC Light Distribution Curve T8-22W-150-AHC iiluminance Temperature test temperature 10.0 Lamp beads pin welding spot Aluminum PCB Aluminum shell Ambient temperature :00: :00:00 Ambient temperature Lamp beads pin Aluminum PCB welding spot Aluminum shell

5 Installation INSTALLATION OR ASSEMBLY INSTRUCTIONS Installation steps: Step 1:Turn off the power to the light fixture at the main service panel or the circuit breaker panel before installation. Step 2:Open the diffuser (if any) and fluorescent tubes. Please dispose the fluorescent lamp tubes properly as they contain mercury. Minimum lamp-to-lamp spacing:10cm Step 3:Open the wiring cover to expose the fluorescent lamp ballast. Check the wires of the light fixture before installation of the LED retrofit kit. If the light fixture is providing with magnetic ballast and starter, disconnect and rewiring the wires at the point as shown in the following figures (see Figure 1 to Figure 3). Cut the wires connected to the ballast and starter, and Lampholders as shown. [X] Remove the ballast and starter. Rewiring the wires from Lampholder A to L and N of the supply circuit by wire nuts/connectors (Not provided with the package). Insulated or capped all unused conductors with wire connectors. If the light fixture is providing with electronic ballast, disconnect and rewiring the wires at the point as shown in the following figures (see Figure 4 to Figure 6).

6 Cut the wires connected to the ballast and Lampholders as shown. [X] Remove the ballast and starter. Rewiring the wires from Lampholder A to L and N of the supply circuit by wire nuts/connectors (Not provided with the package). Insulated or capped all unused conductors with wire connectors. Step 4:Both line and neutral power are required to be connected to the same Lampholder as shown in Figure 3 and Figure 6. Check the wire connectors carefully which shall not be loosened. Be sure that the splices or connections should be insulated reliably, and they should be in the enclosed splice compartment. Step 5 Close the wiring cover. Step 6: Identify one side of the Lampholder which connected to the supply circuit as the live end and marked as LIVE END or L/N for future reference (See Figure 7). Install the LED Lamp Tube to light fixture matching the power side (the side marked with AC ) of the lamp to the LIVE END side of the light fixture. Close the diffuser. This LED Retrofit kit is intended for use with maximum 3 lamps in light fixture with or without diffuser. Step 7:Turn on the light fixture. If the light fixture is not working, turn off the power at the main service/circuit breaker panel and check the wiring connections. Step 8:After modification completed, attach the relamping label which provided with the LED retrofit kit package to the light fixture. The label shall be readily visible by the user during replamping and after installation. For light fixture with maximum 3 lamps, simply connect all the black leads (ungrounded leads) from each Lampholders to the line side (L) of the supply circuit and connect all white leads (grounded leads) from each Lampholders to the neutral side (N) of the supply circuit. See Figure 8 and Figure 9 for 2 lamps and 3 lamps connection in details, respectively.

7 Packing Information Part No. Package dimension N.W. G.W. T8-10W-60-AHC 630X160X190mm, 20pcs/carton 0.14kg/PCS 3.4 kg/ctn T8-18W-120-AHC 1230X160X190mm, 20pcs/carton 0.26kg/PCS 6.5kg/CTN T8-22W-150-AHC 1530X160X190mm, 20pcs/carton 0.31kg/PCS 8.2 kg/ctn

Application 5 Quality warranty 1 2 3 4 5 5 years warranty from the shipping date.

TORSHARE will bare all cost of maintains if the customer can help us to repair locally.

TORSHARE don't have the responsibility to compensate for damage occurred during the transit. Notes 1.

8 Application 5 Quality warranty years warranty from the shipping date. TORSHARE will replace all the failed products due to TORSHARE design/production quality central/material during the warranty period. TORSHARE will bare all cost of maintains if the customer can help us to repair locally. TORSHARE don't have the responsibility to compensate for any incorrect installation or artificial damage. TORSHARE don't have the responsibility to compensate for damage occurred during the transit. Notes 1. The complete installation must be handled by an electrical expert; 2. Please cut off the power when abnormal led lamp found; 3. Lightning protection measure need to be taken on the input terminal, making sure the voltage stable; 4. The led lamp works under the dry and clear environment; 5. Do not disassemble by yourselves, In order to avoid electric shock.

Iconic LED, LLC. "All in one T8" Compatible with or without ballast. WorkswithSingleEndandDoubleEnd

Iconic LED, LLC. All in one T8 Compatible with or without ballast. WorkswithSingleEndandDoubleEnd Iconic ED, ISTED "All in one T8" ompatible with or without ballast. WorkswithSingleEndandDoubleEnd PRODUT SPEIFIATIO DESRIPTIO: ED T8 TUBE SERIES PRODUT MODE: WHD-T8-0WB, WHD-T8-8WB, WHD-T8-WB BASI PARAMETERS