Iconic LED, LLC. "All in one T8" Compatible with or without ballast. WorkswithSingleEndandDoubleEnd

Transcription

1 Iconic ED, ISTED "All in one T8" ompatible with or without ballast. WorkswithSingleEndandDoubleEnd PRODUT SPEIFIATIO DESRIPTIO: ED T8 TUBE SERIES PRODUT MODE: WHD-T8-0WB, WHD-T8-8WB, WHD-T8-WB BASI PARAMETERS Model o. Product ame WHD-T8-0WB WHD-T8-8WB ED T8 TUBE Dimension (mm) 590* 6mm 98* 6mm ED hip SMD 85 Power 0W±W 8W±W ED hip Quantity 8 PS 96 PS Power Factor Power Efficiency ight Efficiency % 0lm/ W % 0lm/ W Input Voltage Frequency 00~ 77V 50/ 60Hz umen Output 00lm±0% 980lm±0% T(K) RI Beam Angle uminous Flux Maintenance ife Span Starting Time Working Humidity Storage Temperature et Weight ( g) ertification 000K-5000K <% after 000 Hours 50,000 Hours.0 Second (@ 0V) 0% ~ 90% -5 ~ U & D Iconic ED, 806 W Pinhook Rd., afayette, A Office: Fax:

2 c Iconic ED, ISTED Application Range: The ED T8 Series is widely used in the following occasions and places, such as shops, bars, marketplaces, restaurants, museums, exhibition halls, signs, storehouse, in-door lighting and atmosphere creation. Features and Benefits Build-in wide voltage driver 90~5V Easy Installation ompatible with electronic and magnetic ballast, don t need to remove any ballast ompatible with current ballasts, no rewiring Better transparencies & high output luminous flux. Wide beam angle (80 Degrees) Instant on/off and no flicking ompatibility ist WHD ED T8 lamps and the compatible ballasts shown on the chart have been tested internally by the manufacturer only and not the ballast manufacturer. WHD has been continually testing our ED lamps on various popular ballasts. We will continue to update this list as additional models are to be tested. If the ballast does not appear on this list, it does not necessarily mean the model is not compatible with the WHD ED T8 lamps. It may just be that the model has not been tested yet. Please contact WHD about ballasts that are not shown on this list. Iconic ED, 806 W Pinhook Rd., afayette, A Office: Fax:

3 Iconic ED, ISTED ISTAATIO OR ASSEMBY ISTRUTIOS Installation steps: Step :Turn off the power to the light fixture at the main service panel or the circuit breaker panel before installation. Step :Open the diffuser (if any) and fluorescent tubes. Please dispose the fluorescent lamp tubes properly as they contain mercury. ampholder Minimum lamp-to-lamp-spacing: 0cm amp-to-lamp spacing is 0 cm Step :Open the wiring cover to expose the fluorescent lamp ballast. heck the wires of the light fixture before installation of the ED retrofit kit. If the light fixture is providing with magnetic ballast and starter, disconnect and rewiring the wires at the point as shown in the following figures (see Figure to Figure ). ampholder A ampholder B Figure : Before retrofit ut the wires connected to the ballast and starter, and ampholders as shown. [X] Remove the ballast and starter. ampholder A ampholder B Figure : Under retrofit Rewiring the wires from ampholder A to and of the supply circuit by wire nuts/connectors (ot provided with the package). Insulated or capped all unused conductors with wire connectors. ampholder A ampholder B Figure : After retrofit Iconic ED, 806 W Pinhook Rd., afayette, A Office: Fax:

4 Iconic ED, ISTED ampholder A ampholder B If the light fixture is providing with electronic ballast, disconnect and rewiring the wires at the point as shown in the following figures (see Figure to Figure 6). Electronic Figure : Before retrofit ampholder A ampholder B ut the wires connected to the ballast and ampholders as shown. [X] Remove the ballast and starter. Electronic Figure 5: Under retrofit ampholder A ampholder B Rewiring the wires from ampholder A to and of the supply circuit by wire nuts/connectors (ot provided with the package). Insulated or capped all unused conductors with wire connectors. Electronic Figure 6: After Retrofit Step : Both line and neutral power are required to be connected to the same ampholder as shown in Figure and Figure 6. heck the wire connectors carefully which shall not be loosened. Be sure that the splices or connections should be insulated reliably, and they should be in the enclosed splice compartment. Step 5: lose the wiring cover. Step 6: Identify one side of the ampholder which connected to the supply circuit as the live end and marked as IVE ED or / for future reference (See Figure 7 OR 7A). Install the ED amp Tube to light fixture matching the power side (the side marked with ) of the lamp to the IVE ED side of the light fixture. lose the diffuser. This ED Retrofit kit is intended for use with maximum lamps in light fixture with or without diffuser V ED TUBE OR 00-77V ED TUBE IVE ED Figure 7A IVE ED Figure 7 Step 7:Turn on the light fixture. If the light fixture is not working, turn off the power at the main service/circuit breaker panel and check the wiring connections. Step 8:After modification completed, attach the relamping label which provided with the ED retrofit kit package to the light fixture. The label shall be readily visible by the user during replamping and after installation. Iconic ED, 806 W Pinhook Rd., afayette, A Office: Fax:

5 ISTED ISTAATIO ISTRUTIO comparable installation. Switch off the electricity. Detach the conventional lamp from the fitting by turning it 90. Remove the conventional lamp. Insert the ED Tube into the lamp fitting 5. Secure it in position by turning the ED Tube Switch on electricity ED TUBE ompatible mode Electronic ED TUBE Iconic ED, ompatib le mode Single End and Double End installation. Turn off the power to the light fixture at the breaker panel before installation.. Open the diffuser from the light fixture.. Remove the fluorescent tubes. Please dispose of these items properly as they contain mercury. ED TUBE ED TUBE Magnetic ED TUBE ED TUBE ED TUBE ED TUBE Iconic ED, 806 W Pinhook Rd., afayette, A Office: Fax:

6 Iconic ED, ISTED 6PS 6ayer Packing quantity: 6PS H W arton S iz e : 8." X W 7.87" X H 7.87" or 0 X W 00 X H 00 mm (WHD-T8-8WB).8" X W 7.87" X H 7.87" or 60 X W 00 X H 00 mm (WHD-T8-0WB) Iconic ED, 806 W Pinhook Rd., afayette, A Office: Fax: