Main Brackets. Bagwell Brackets. 2 Footrest. Brackets

Transcription

1 rear flip seat star cart classic installation instructions included: Footrest 2 Bagwell 2 Main Seat Frame HD Bracket Seat Back SupportBracket 2 Arm Rests 2 Struts 2 Footrest 2 Lean Back tools needed: (not supplied) Bagwell Power Drill 1 mm wrench 1mm socket Phillips head screwdriver #3 Main 2 Lean Back Seat Back Support Bracket Lean Back Seat Bottom 2 Armrests Seat Frame 2 Footrest HD Bracket Footrest Struts Madjax recommends professional installation. If you choose to not have this product installed by a professional, we highly recommend that you exercise caution, care, and patience when installing this product. 1 Remove factory canopy and retain hardware. remove 2 Remove basket by removing hardware located inside motor compartment. Retain factory hardware.

2 3 Remove motor cover for easy access to install main bracket. Attach main bracket as shown on both sides using hardware from Pack 1 or retained hardware from Step 2. Remove factory hardware and drill out holes with a 1/2 drill bit. Attach bagwell brackets using hardware from Pack 1. 4 Attach seat frame to brackets using hardware from Pack 2. 6 Attach seat frame to bagwell brackets using hardware Pack 2.

3 IMPORTANT: Do not tighten hardware until step 14 is complete. Attach seat back support and ar mrests to seat frame using hardware from Pack 3. 8 Use rubber spacers from Pack 3 between seat back support and armrest as shown. 9 Attach armrest to rear portion of seat frame using counter sink phillips head hardware from Pack Attach new rear struts to seat back support using hardware from Pack 4. Attach canopy hardware retained from step 1.

4 11 (A) Attach footrest to bagwell bracket using remaining hardware from Pack 4. A B (B) Attach footrest brackets to footrest and armrest using remaining hardware from Pack Attach lean back brackets to seat back using hardware form Pack. Attach front seat back using retained hardware from step Attach seat back to seat back support using hardware from Pack 4. Tighten all hardware.

5 Place HD bracket on flip seat as shown. Align bracket holes to the flip seat mounting holes Make sure the thickest part of the seat bottom points towards the footrest. Center seat bottom from left to right on flip frame. Press cushion firmly against HD bracket and seat frame. Using provided hardware tighten the seat bottom to seat frame as shown. Hardware Pack GENESIS10 REAR FLIP SEAT FOR STAR CART WARRANTY PARTS EXPLODED VIEW DIAGRAM Pack 1: 4 8mm x 2mm hex head bolts 4 8mm flat washers 2 10mm x 3mm hex head bolts 4 10mm flat washers 2 10mm lock nuts Pack 2: 4 10mm x 2mm hex head bolts 8 10mm flat washers 4 10mm lock nuts Pack 3: 4 10mm x 0mm hex head bolts 2 10mm x 40mm #3 countersunk bolts 10 10mm flat washers 6 10mm lock nuts 2 Rubber spacers Pack 4: 6 10 x 0mm hex head bolts 2 10mm x 4 mm hex head bolts 2 10 x 2mm hex head bolts 20 10mm flat washers 10 10mm lock nuts Pack : 4 6mm x 2mm hex head bolts 4 6mm lock washers 4 6mm flat washers Pack 6: 8 8mm x 3mm #3 countersunk bolts INSTALLATION COMPLETE visit for installation videos *E-Z-GO, E-Z-Go TXT, E-Z-Go FREEDOM TXT, E-Z-Go CUSHMAN and E-Z-Go RXV are registered trademarks of Textron Innovations, Inc. Club Car, Club Car Precedent, and Club Car DS are registered trademarks of Ingersoll Rand, Inc. Yamaha, Yamaha Drive, G-14, G-16, G-19, and G-22 are registered trademarks of Yamaha Golf-Car Company. Any reference to Club Car, E-Z-Go, or Yamaha or their associated trademarks, word marks, and products are only for purposes of identifying golf carts with which this Madjax product is compatible. Madjax products are aftermarket parts and are not original equipment parts. Madjax is not connected to, affiliated with, sponsored by, or endorsed by either Textron Innovations, Inc., Ingersoll Rand, Inc., Yamaha Golf Cart Company, or any of their parent or subsidiary companies GENESIS10 REAR FLIP SEAT FOR STAR CART (01-023) ITEM PART NO. DESCRIPTION QTY ITEM NO. PART NO. NO. DESCRIPTION QTY 1 W Lean Back Cushion-Almond 1 11 W Frame Bracket (Pass) 1 Seat 2 W Seat Cushion-Almond 1 3 W Flip Poly Board 1 4 W Main Frame w/ New Poly Board 1 W Arm Rest 2 6 W01-8- Horizontal Frame Bracket 1 W Bagwell Bracket 2 8 W Foot Plate 1 9 W Foot Plate Bracket (Pass) 1 10 W Foot Plate Bracket (Driver) W Seat Frame Bracket (Driver) 1 W Lean Back Bracket 2 14 W Rear Strut (Pass) 1 1 W Rear Strut (Driver) 1 16 W Hardware Pack 1 Date Issued: 2/2/1