INSTRUCTIONS 360 Y-DROP

Transcription

1 INSTRUCTIONS 60 Y-DROP JOHN DEERE Y-DROP REGISTRATION Please visit productregistration.60yieldcenter.com to complete the product registration for your 60 Y-DROP so we can better support our products from day one and ensure you have the latest upgrades, warranty parts and technical support. Thank you! 60YIELDCENTER.COM V -..06

2 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The 60 Y-DROP unit should be precisely centered on the machine, as this is critical to the assembly of the system to the sprayer and for mounting the system to your sprayer boom. There are, however, many boom variations among all sprayer models. Your sprayer may not be identical to the model in the following steps of the guide, and the pictures may not exactly reflect your model. While these steps will help you install most of your 60 Y-DROP system, you may need to custom-fit some components with your particular boom. RECOMMENDED TOOLS Ratchet wrench with /" and 9/6" deep well sockets /8" -point socket /" and 9/6" combination wrenches # Phillips screwdriver (for the shield installation) TORQUE VALUES Refer to these torque values when tightening all fasteners 5/6" stainless U-bolt 5 ft/lbs 5/6" stainless Set screw 5 ft/lbs /8" carbon U-bolt 5 ft/lbs 5/6" carbon U-bolt 0 ft/lbs 5/6" carbon Stop bolt 0 ft/lbs QUESTIONS Call our Product Support team at

3 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 I. ESTABLISH DROP LOCATIONS Figures and Step Locate the center of the machine and identify the location of all the drops. On the sprayer boom, mark where each riser mount will be located. This will ensure that the extension tubes will not interfere with the riser mounts. Figure Figure Step Starting at the wing fold pivot pin on the primary boom, measure and mark points at 69", ", 0", 67" and 0" (all measurements are ±5"). Repeat for the other primary boom. Figure 0" 67" 0" " 69" Figure 60YIELDCENTER.COM

4 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 II. INSTALL PRIMARY BOOM SPRAYER MOUNT PACKAGE Figure Step Step With the thread pointing down, install square U-bolt () on the top of the OEM primary boom. Bag AG Install bracket assembly () and flange lock nut (). Hardware Kit D Repeat Steps and for the other OEM mount bracket. Figure Step Install extension tube (). Repeat Steps - for the remaining mounting positions on the primary booms. Figure 5 Step Install boom bracket () onto extension tube (). Figure 5 60YIELDCENTER.COM

5 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 III. INSTALL CENTER SECTION EXTENSION TUBE Figures 6 and 7 Step Install " top plate () and 8" top plate () using the supplied hardware. Step Install bracket assemblies (). Step Install extension tube (). Step Install drop tube (5) onto the extention Figure 6 Step 5 tube () and install bolt assembly (6). Hardware Kit B Install stainless steel set screw and jam 6 nut assembly. Step 6 Install stop bolt at the rear of the extention tube. Hardware Kit D 5 Repeat Steps -6 for the other center section extension tube assembly. Figure 7 60YIELDCENTER.COM 5

6 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 IV. INSTALL 60 Y-DROP BOOM Figure 8 Step Assemble 5' boom sections () utilizing 8" boom connectors () and the supplied hardware. Hardware Bag CC Step Step Repeat Step as needed in order to assemble the entire 60 Y-DROP boom. Set the 60 Y-DROP boom assembly onto boom bracket (). Figure 8 Repeat Steps - for the remaining boom assemblies. CAUTION: The 60 Y-DROP boom assembly may weigh up to 50 lbs. (68 kg). Exercise caution and enlist help for this process. Figure 9 Step In order to span the full length of the center section 60 Y-DROP boom, you will need to cut and drill one of the 5' boom sections to '. Mount this ' section between two full 5' boom sections. Drill a 7/6" through hole centered " from the outside edge. Figures 0 and Step 5 Install square U-bolt (), the 5/6" extra thick washers, and the 5/6" nuts over the 60 Y-DROP boom (). Hardware Kit A Figure 9 Figure 0 Step 6 Step 7 Install stop bolt () at the both the front and the rear of the extension tube. Repeat for remaining stop bolts. Hardware Kit B Install stainless steel set screw and jam nut assembly (). See Figure for detail. Repeat for the remaining mount assemblies on the primary boom. Figure 60YIELDCENTER.COM 6

7 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 VI. INSTALL BREAKAWAY ASSEMBLY - ONE PIECE Figure Step Install breakaway assembly - one piece () using the square U-bolts () and the extra thick washer and Nylock nut. Repeat for the remaining breakaway assemblies - one piece. Hardware Kit C Figure Figure may show more or fewer mounts than your installation. The alignment and quantity of the mounts will depend on your row spacing. Figure Figure Step Install riser tube assembly () into the breakaway assembly - one piece (). Step Install pin (). Repeat Steps and for the remaining riser tube assemblies. NOTE: Included in most sprayer mount packages are standard riser mounts to be used when primary booms are folded and in transport mode. These standard riser mounts should be mounted in locations that allow you to relocate the drops away from potential tire interference. See "Install Riser Mounts Without Breakaway Assemblies" section on next page for more instructions. Figure Figure 60YIELDCENTER.COM 7

8 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 V. INSTALL RISER MOUNTS WITHOUT BREAKAWAY ASSEMBLIES (OPTIONAL) Figure 5 Step Install riser mount () using the square U-bolts () and the extra thick washer and nylock nut. Repeat for the remaining riser mounts. Hardware Kit C Figure 6 Figure 6 may show more or fewer riser mounts than your installation. The alignment and quantity of the riser mounts will depend on your row spacing. Figure 5 Figure 7 Step Install riser tube assembly () into the riser mount (). Step Install pin (). Repeat Steps and for the remaining riser tube assemblies. Figure 6 Figure 7 60YIELDCENTER.COM 8

9 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 VI. INSTALL SHIELDS AND RISER HOSES Figure 8 Step Install shield () onto riser tube (). Figure 9 Step Install base unit () onto riser tube (). Figure 0 Step Figure Step Assemble drag hoses () to 60 Y-DROP base and secure with hose clamps (). Note the orientation of the drag hose clamps. The tails should point inward. Figure 8 Figure 9 Figure 0 Figure 60YIELDCENTER.COM 9

10 INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 VI. INSTALL SHIELDS AND RISER HOSES (continued) Figure CAUTION: Do NOT use a drill or impact driver for Steps 5 and 6. Step 5 Install two ½" screws (). Figure Step 6 Install two ¾" screws (). Step 7 Figure Step 8 Figure Step 9 Install rubber washer () into the Y. Install riser hose assembly () into the Y. Route riser hose assembly () as shown in Figure. Step 0 Install the riser hose assembly to the OEM nozzle body. Figure Step Use equally spaced plastic ties to secure the riser hose assembly. Repeat Steps - for the remaining 60 Y-DROP Shields. Figure INSTALLATION COMPLETE. 60YIELDCENTER.COM All other trademarks are the property of 60 Yield Center, its affiliates and/or its licensors Yield Center. All rights reserved.